CS5345 104 dB, 24-Bit, 192 kHz Stereo Audio ADC A/D Features General Description Multi-Bit Delta Sigma Modulator The CS5345 integrates an analog multiplexer, programmable gain amplifier, and stereo audio analog-to-digital converter. The CS5345 performs stereo analog-to-digital (A/D) conversion of up to 24-bit serial values at sample rates up to 192 kHz. 104 dB Dynamic Range -95 dB THD+N Stereo 6:1 Input Multiplexer Programmable Gain Amplifier (PGA) - 12 dB Gain, 0.5 dB Step Size - Zero Crossing, Click-Free Transitions Stereo Microphone Inputs - +32 dB Gain Stage - Low-Noise Bias Supply Up to 192 kHz Sampling Rates Selectable Serial Audio Interface Formats - Left-Justified up to 24-bit - IS up to 24-bit High-Pass Filter or DC Offset Calibration System Features Power-Down Mode +3.3 V to +5 V Analog Power Supply, Nominal +3.3 V to +5 V Digital Power Supply, Nominal Direct Interface with 1.8 V to 5 V Logic Levels Pin-Compatible with CS4245 http://www.cirrus.com Register Configuration PCM Serial Interface Serial Audio Output Level Translator Reset Level Translator Interrupt Overflow The output of the PGA is followed by an advanced 5thorder, multi-bit delta sigma modulator and digital filtering/decimation. Sampled data is transmitted by the serial audio interface at rates from 4 kHz to 192 kHz in either Slave or Master Mode. Integrated level translators allow easy interfacing between the CS5345 and other devices operating over a wide range of logic levels. The CS5345 is available in a 48-pin LQFP package in Commercial (-10 to +70 C) and Automotive (-40 to +105 C) grade. The CDB5345 Customer Demonstration board is also available for device evaluation and implementation suggestions. Please refer to "Ordering Information" on page 41 for complete details. 3.3 V to 5 V 1.8 V to 5 V IC/SPI Control Data A 6:1 stereo input multiplexer is included for selecting between line-level and microphone-level inputs. The microphone input path includes a +32 dB gain stage and a low-noise bias voltage supply. The PGA is available for line or microphone inputs and provides gain/attenuation of 12 dB in 0.5 dB steps. High Pass Filter High Pass Filter Low-Latency Anti-Alias Filter Low-Latency Anti-Alias Filter 3.3 V to 5 V Left PGA Output Right PGA Output Internal Voltage Reference Stereo Input 1 Stereo Input 2 Stereo Input 3 Multibit Oversampling ADC PGA Multibit Oversampling ADC PGA Copyright (c) Cirrus Logic, Inc. 2007 (All Rights Reserved) MUX +32 dB Stereo Input 4 / Mic Input 1 & 2 +32 dB Stereo Input 5 Stereo Input 6 AUGUST '07 DS658F2 CS5345 TABLE OF CONTENTS 1. PIN DESCRIPTIONS ......................................................................................................................... 5 2. CHARACTERISTICS AND SPECIFICATIONS ...................................................................................... 7 SPECIFIED OPERATING CONDITIONS ............................................................................................. 7 ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 7 ADC ANALOG CHARACTERISTICS ................................................................................................... 8 ADC ANALOG CHARACTERISTICS ................................................................................................. 10 ADC DIGITAL FILTER CHARACTERISTICS ..................................................................................... 11 PGAOUT ANALOG CHARACTERISTICS .......................................................................................... 12 PGAOUT ANALOG CHARACTERISTICS .......................................................................................... 13 PGAOUT ANALOG CHARACTERISTICS .......................................................................................... 14 DC ELECTRICAL CHARACTERISTICS ............................................................................................. 15 DIGITAL INTERFACE CHARACTERISTICS ...................................................................................... 16 SWITCHING CHARACTERISTICS - SERIAL AUDIO PORT ............................................................. 17 SWITCHING CHARACTERISTICS - CONTROL PORT - IC FORMAT ............................................ 20 SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT ........................................... 21 3. TYPICAL CONNECTION DIAGRAM ................................................................................................... 22 4. APPLICATIONS ................................................................................................................................... 23 4.1 Recommended Power-Up Sequence ............................................................................................. 23 4.2 System Clocking ............................................................................................................................. 23 4.2.1 Master Clock ......................................................................................................................... 23 4.2.2 Master Mode ......................................................................................................................... 24 4.2.3 Slave Mode ........................................................................................................................... 24 4.3 High-Pass Filter and DC Offset Calibration .................................................................................... 24 4.4 Analog Input Multiplexer, PGA, and Mic Gain ................................................................................ 25 4.5 Input Connections ........................................................................................................................... 25 4.6 PGA Auxiliary Analog Output ......................................................................................................... 25 4.7 Control Port Description and Timing ............................................................................................... 26 4.7.1 SPI Mode ............................................................................................................................... 26 4.7.2 IC Mode ................................................................................................................................ 26 4.8 Interrupts and Overflow .................................................................................................................. 28 4.9 Reset .............................................................................................................................................. 28 4.10 Synchronization of Multiple Devices ............................................................................................. 28 4.11 Grounding and Power Supply Decoupling .................................................................................... 28 5. REGISTER QUICK REFERENCE ........................................................................................................ 30 6. REGISTER DESCRIPTION .................................................................................................................. 31 6.1 Chip ID - Register 01h .................................................................................................................... 31 6.2 Power Control - Address 02h ......................................................................................................... 31 6.2.1 Freeze (Bit 7) ......................................................................................................................... 31 6.2.2 Power-Down MIC (Bit 3) ........................................................................................................ 31 6.2.3 Power-Down ADC (Bit 2) ....................................................................................................... 31 6.2.4 Power-Down Device (Bit 0) ................................................................................................... 31 6.3 ADC Control - Address 04h ............................................................................................................ 32 6.3.1 Functional Mode (Bits 7:6) .................................................................................................... 32 6.3.2 Digital Interface Format (Bit 4) .............................................................................................. 32 6.3.3 Mute (Bit 2) ............................................................................................................................ 32 6.3.4 High-Pass Filter Freeze (Bit 1) .............................................................................................. 32 6.3.5 Master / Slave Mode (Bit 0) ................................................................................................... 32 6.4 MCLK Frequency - Address 05h .................................................................................................... 33 6.4.1 Master Clock Dividers (Bits 6:4) ............................................................................................ 33 6.5 PGAOut Control - Address 06h ...................................................................................................... 33 6.5.1 PGAOut Source Select (Bit 6) ............................................................................................... 33 6.6 Channel B PGA Control - Address 07h .......................................................................................... 33 2 DS658F2 CS5345 6.6.1 Channel B PGA Gain (Bits 5:0) ............................................................................................. 33 6.7 Channel A PGA Control - Address 08h .......................................................................................... 34 6.7.1 Channel A PGA Gain (Bits 5:0) ............................................................................................. 34 6.8 ADC Input Control - Address 09h ................................................................................................... 34 6.8.1 PGA Soft Ramp or Zero Cross Enable (Bits 4:3) .................................................................. 34 6.8.2 Analog Input Selection (Bits 2:0) ........................................................................................... 35 6.9 Active Level Control - Address 0Ch ................................................................................................ 35 6.9.1 Active High/Low (Bit 0) .......................................................................................................... 35 6.10 Interrupt Status - Address 0Dh ..................................................................................................... 35 6.10.1 Clock Error (Bit 3) ................................................................................................................ 36 6.10.2 Overflow (Bit 1) .................................................................................................................... 36 6.10.3 Underflow (Bit 0) .................................................................................................................. 36 6.11 Interrupt Mask - Address 0Eh ....................................................................................................... 36 6.12 Interrupt Mode MSB - Address 0Fh .............................................................................................. 36 6.13 Interrupt Mode LSB - Address 10h ............................................................................................... 36 7. PARAMETER DEFINITIONS ................................................................................................................ 37 8. FILTER PLOTS .................................................................................................................................. 38 9. PACKAGE DIMENSIONS .................................................................................................................... 40 10. THERMAL CHARACTERISTICS AND SPECIFICATIONS ............................................................. 40 11. ORDERING INFORMATION ........................................................................................................ 41 12. REVISION HISTORY .......................................................................................................................... 41 LIST OF FIGURES Figure 1.Master Mode Serial Audio Port Timing ....................................................................................... 18 Figure 2.Slave Mode Serial Audio Port Timing ......................................................................................... 18 Figure 3.Format 0, Left-Justified up to 24-Bit Data ................................................................................... 19 Figure 4.Format 1, IS up to 24-Bit Data ................................................................................................... 19 Figure 5.Control Port Timing - IC Format ................................................................................................. 20 Figure 6.Control Port Timing - SPI Format ................................................................................................ 21 Figure 7.Typical Connection Diagram ....................................................................................................... 22 Figure 8.Master Mode Clocking ................................................................................................................ 24 Figure 9.Analog Input Architecture ............................................................................................................ 25 Figure 10.Control Port Timing in SPI Mode .............................................................................................. 26 Figure 11.Control Port Timing, IC Write ................................................................................................... 27 Figure 12.Control Port Timing, IC Read ................................................................................................... 27 Figure 13.Single-Speed Stopband Rejection ............................................................................................ 38 Figure 14.Single-Speed Stopband Rejection ............................................................................................ 38 Figure 15.Single-Speed Transition Band (Detail) ...................................................................................... 38 Figure 16.Single-Speed Passband Ripple ................................................................................................ 38 Figure 17.Double-Speed Stopband Rejection ........................................................................................... 38 Figure 18.Double-Speed Stopband Rejection ........................................................................................... 38 Figure 19.Double-Speed Transition Band (Detail) .................................................................................... 39 Figure 20.Double-Speed Passband Ripple ............................................................................................... 39 Figure 21.Quad-Speed Stopband Rejection ............................................................................................. 39 Figure 22.Quad-Speed Stopband Rejection ............................................................................................. 39 Figure 23.Quad-Speed Transition Band (Detail) ....................................................................................... 39 Figure 24.Quad-Speed Passband Ripple ................................................................................................. 39 LIST OF TABLES Table 1. Speed Modes .............................................................................................................................. 23 Table 2. Common Clock Frequencies ....................................................................................................... 23 Table 3. Slave Mode Serial Bit Clock Ratios ............................................................................................. 24 Table 4. Device Revision .......................................................................................................................... 31 DS658F2 3 CS5345 Table 5. Freeze-able Bits .......................................................................................................................... 31 Table 6. Functional Mode Selection .......................................................................................................... 32 Table 7. Digital Interface Formats ............................................................................................................. 32 Table 8. MCLK Frequency ........................................................................................................................ 33 Table 9. PGAOut Source Selection ........................................................................................................... 33 Table 10. Example Gain and Attenuation Settings ................................................................................... 34 Table 11. PGA Soft Cross or Zero Cross Mode Selection ........................................................................ 35 Table 12. Analog Input Multiplexer Selection ............................................................................................ 35 4 DS658F2 CS5345 TSTI NC NC NC SDOUT SCLK LRCK MCLK DGND VD INT OVFL 1. PIN DESCRIPTIONS 48 47 46 45 44 43 42 41 40 39 38 37 SDA/CDOUT 1 36 VLS SCL/CCLK 2 35 TSTO AD0/CS 3 34 NC AD1/CDIN 4 33 NC VLC 5 32 AGND RESET 6 31 AGND AIN3A 7 30 VA AIN3B 8 29 PGAOUTB AIN2A 9 28 PGAOUTA AIN2B 10 27 AIN6B AIN1A 11 26 AIN6A AIN1B 12 25 MICBIAS CS5345 AIN5B AIN5A AIN4B/MICIN2 AIN4A/MICIN1 TSTO FILT+ TSTO VQ AFILTB AFILTA VA AGND 13 14 15 16 17 18 19 20 21 22 23 24 Pin Name # Pin Description SDA/CDOUT 1 Serial Control Data (Input/Output) - SDA is a data I/O in IC(R) Mode. CDOUT is the output data line for the control port interface in SPITM Mode. SCL/CCLK 2 Serial Control Port Clock (Input) - Serial clock for the serial control port. AD0/CS 3 Address Bit 0 (IC) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in IC Mode; CS is the chip-select signal for SPI format. AD1/CDIN 4 Address Bit 1 (IC) / Serial Control Data Input (SPI) (Input) - AD1 is a chip address pin in IC Mode; CDIN is the input data line for the control port interface in SPI Mode. VLC 5 Control Port Power (Input) - Determines the required signal level for the control port interface. Refer to the Recommended Operating Conditions for appropriate voltages. RESET 6 Reset (Input) - The device enters a low-power mode when this pin is driven low. AIN3A AIN3B 7 8 Stereo Analog Input 3 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. AIN2A AIN2B 9 10 Stereo Analog Input 2 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. DS658F2 5 CS5345 AIN1A AIN1B 11 12 Stereo Analog Input 1 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. AGND 13 Analog Ground (Input) - Ground reference for the internal analog section. VA 14 Analog Power (Input) - Positive power for the internal analog section. AFILTA 15 Antialias Filter Connection (Output) - Antialias filter connection for the channel A ADC input. AFILTB 16 Antialias Filter Connection (Output) - Antialias filter connection for the channel B ADC input. VQ 17 Quiescent Voltage (Output) - Filter connection for the internal quiescent reference voltage. TSTO 18 Test Pin (Output) - This pin must be left unconnected. FILT+ 19 Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. TSTO 20 Test Pin - This pin must be left unconnected. AIN4A/MICIN1 AIN4B/MICIN2 21 22 Stereo Analog Input 4 / Microphone Input 1 & 2 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. AIN5A AIN5B 23 24 Stereo Analog Input 5 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. MICBIAS 25 Microphone Bias Supply (Output) - Low-noise bias supply for external microphone. Electrical characteristics are specified in the DC Electrical Characteristics specification table. AIN6A AIN6B 26 27 Stereo Analog Input 6 (Input) - The full-scale level is specified in the ADC Analog Characteristics specification table. PGAOUTA PGAOUTB 28 29 PGA Analog Audio Output (Output) - Either an analog output from the PGA block or high impedance. See "PGAOut Source Select (Bit 6)" on page 33. VA 30 Analog Power (Input) - Positive power for the internal analog section. AGND 31 32 Analog Ground (Input) - Ground reference for the internal analog section. NC 33 34 No Connect - These pins are not connected internally and should be tied to ground to minimize any potential coupling effects. TSTO 35 Test Pin (Output) - This pin must be left unconnected. VLS 36 Serial Audio Interface Power (Input) - Determines the required signal level for the serial audio interface. Refer to the Recommended Operating Conditions for appropriate voltages. TSTI 37 Test Pin (Input) - This pin must be connected to ground. NC 38, 39, 40 No Connect - These pins are not connected internally and should be tied to ground to minimize any potential coupling effects. SDOUT 41 Serial Audio Data Output (Output) - Output for two's complement serial audio data. SCLK 42 Serial Clock (Input/Output) - Serial clock for the serial audio interface. LRCK 43 Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the serial audio data line. MCLK 44 Master Clock (Input) - Clock source for the ADC's delta-sigma modulators. DGND 45 Digital Ground (Input) - Ground reference for the internal digital section. VD 46 Digital Power (Input) - Positive power for the internal digital section. INT 47 Interrupt (Output) - Indicates an interrupt condition has occurred. OVFL 48 Overflow (Output) - Indicates an ADC overflow condition is present. 6 DS658F2 CS5345 2. CHARACTERISTICS AND SPECIFICATIONS SPECIFIED OPERATING CONDITIONS AGND = DGND = 0 V; All voltages with respect to ground. Parameters Symbol Min Nom Max Units Analog Digital Logic - Serial Port Logic - Control Port Ambient Operating Temperature (Power Applied) Commercial Automotive VA VD VLS VLC TA TA 3.13 3.13 1.71 1.71 -10 -40 5.0 3.3 3.3 3.3 - 5.25 (Note 1) 5.25 5.25 +70 +105 V V V V C C DC Power Supplies: Notes: 1. Maximum of VA+0.25 V or 5.25 V, whichever is less. ABSOLUTE MAXIMUM RATINGS AGND = DGND = 0 V All voltages with respect to ground. (Note 2) Parameter DC Power Supplies: Input Current Analog Digital Logic - Serial Port Logic - Control Port (Note 3) Analog Input Voltage Symbol Min Max Units VA VD VLS VLC Iin -0.3 -0.3 -0.3 -0.3 +6.0 +6.0 +6.0 +6.0 V V V V - 10 mA VINA AGND-0.3 VA+0.3 V VIND-S VIND-C -0.3 -0.3 VLS+0.3 VLC+0.3 V V Ambient Operating Temperature (Power Applied) TA -50 +125 C Storage Temperature Tstg -65 +150 C Digital Input Voltage Logic - Serial Port Logic - Control Port 2. Operation beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. 3. Any pin except supplies. Transient currents of up to 100 mA on the analog input pins will not cause SCR latch-up. DS658F2 7 CS5345 ADC ANALOG CHARACTERISTICS Test conditions (unless otherwise specified): AGND = DGND = 0 V; VA = 3.13 V to 5.25 V; VD = 3.13 V to 5.25 V or VA + 0.25 V, whichever is less; VLS = VLC = 1.71 V to 5.25 V; TA = -10 to +70 C for Commercial or -40 to +85 C for Automotive; Input test signal: 1 kHz sine wave; measurement bandwidth is 10 Hz to 20 kHz; Fs = 48/96/192 kHz.; All connections as shown in Figure 7 on page 22. Line-Level Inputs Commercial Grade Parameter Symbol Dynamic Performance for VA = 4.75 V to 5.25 V Automotive Grade Min Typ Max Min Typ Max Unit 98 95 - 104 101 98 - 96 93 - 104 101 98 - dB dB dB 92 89 - 98 95 92 - 90 87 - 98 95 92 - dB dB dB - -95 -81 -41 -92 -89 - - -95 -81 -41 -92 -87 - dB dB dB dB - -92 -75 -35 -89 -86 - - -92 -75 -35 -89 -84 - dB dB dB dB 93 90 - 101 98 95 - 91 88 - 101 98 95 - dB dB dB 89 86 - 95 92 89 - 87 84 - 95 92 89 - dB dB dB - -92 -78 -38 -84 -86 - - -92 -78 -38 -84 -84 - dB dB dB dB - -89 -72 -32 -81 -83 - - -89 -72 -32 -81 -81 - dB dB dB dB Dynamic Range (Note 6) (Note 6) PGA Setting: -12 dB to +6 dB A-weighted unweighted 40 kHz bandwidth unweighted PGA Setting: +12 dB Gain A-weighted unweighted 40 kHz bandwidth unweighted Total Harmonic Distortion + Noise (Note 5) PGA Setting: -12 dB to +6 dB -1 dB -20 dB -60 dB (Note 6) 40 kHz bandwidth -1 dB THD+N PGA Setting: +12 dB Gain -1 dB -20 dB -60 dB (Note 6) 40 kHz bandwidth -1 dB Dynamic Performance for VA = 3.13 V to 3.46 V Dynamic Range (Note 6) (Note 6) PGA Setting: -12 dB to +6 dB A-weighted unweighted 40 kHz bandwidth unweighted PGA Setting: +12 dB Gain A-weighted unweighted 40 kHz bandwidth unweighted Total Harmonic Distortion + Noise (Note 5) PGA Setting: -12 dB to +6 dB -1 dB -20 dB -60 dB (Note 6) 40 kHz bandwidth -1 dB THD+N PGA Setting: +12 dB Gain -1 dB -20 dB -60 dB (Note 6) 40 kHz bandwidth -1 dB 8 DS658F2 CS5345 Line-Level Inputs Commercial Grade Parameter Symbol Interchannel Isolation Automotive Grade Min Typ Max Min Typ Max Unit - 90 - - 90 - dB - 100 - 10 - - 100 - 10 - % ppm/C DC Accuracy Gain Error Gain Drift Line-Level Input Characteristics Full-scale Input Voltage Input Impedance (Note 4) Maximum Interchannel Input Impedance Mismatch 0.51*VA 0.57*VA 0.63*VA 0.51*VA 0.57*VA 0.63*VA 6.12 6.8 7.48 5.44 6.8 8.16 - 5 - - 5 - Vpp k % Line-Level and Microphone-Level Inputs Commercial Grade Parameter Symbol Automotive Grade Min Typ Max Min Typ Max Unit - 0.1 - - 0.1 - dB - 0.5 - 0.4 - 0.5 - 0.4 dB dB DC Accuracy Interchannel Gain Mismatch Programmable Gain Characteristics Gain Step Size Absolute Gain Step Error 4. Valid for the selected input pair. DS658F2 9 CS5345 ADC ANALOG CHARACTERISTICS (Continued) Microphone-Level Inputs Commercial Grade Parameter Symbol Dynamic Performance for VA = 4.75 V to 5.25 V Automotive Grade Min Typ Max Min Typ Max Unit 77 74 83 80 - 75 72 83 80 - dB dB 65 62 71 68 - 63 60 71 68 - dB dB - -80 -60 -20 -74 - - -80 -60 -20 -72 - dB dB dB - -68 - - -68 - dB 77 74 83 80 - 75 72 83 80 - dB dB 65 62 71 68 - 63 60 71 68 - dB dB - -80 -60 -20 -74 - - -80 -60 -20 -72 - dB dB dB - -68 80 - - -68 80 - dB dB - 300 5 - - 300 5 - % ppm/C Dynamic Range PGA Setting: -12 dB to 0 dB A-weighted unweighted PGA Setting: +12 dB A-weighted unweighted Total Harmonic Distortion + Noise (Note 5) PGA Setting: -12 dB to 0 dB -1 dB -20 dB THD+N -60 dB PGA Setting: +12 dB -1 dB Dynamic Performance for VA = 3.13 V to 3.46 V Dynamic Range PGA Setting: -12 dB to 0 dB A-weighted unweighted PGA Setting: +12 dB A-weighted unweighted Total Harmonic Distortion + Noise (Note 5) PGA Setting: -12 dB to 0 dB -1 dB -20 dB THD+N -60 dB PGA Setting: +12 dB -1 dB Interchannel Isolation DC Accuracy Gain Error Gain Drift Microphone-Level Input Characteristics Full-scale Input Voltage Input Impedance (Note 7) 0.013*VA 0.017*VA 0.021*VA 0.013*VA 0.017*VA 0.021*VA 60 60 - Vpp k 5. Referred to the typical line-level full-scale input voltage 6. Valid for Double- and Quad-Speed Modes only. 7. Valid when the microphone-level inputs are selected. 10 DS658F2 CS5345 ADC DIGITAL FILTER CHARACTERISTICS Parameter (Notes 8, 10) Symbol Min Typ Max Unit 0 - 0.4896 Fs - - 0.035 dB 0.5688 - - Fs 70 - - dB - 12/Fs - s 0 - 0.4896 Fs - - 0.025 dB Single-Speed Mode Passband (-0.1 dB) Passband Ripple Stopband Stopband Attenuation Total Group Delay (Fs = Output Sample Rate) tgd Double-Speed Mode Passband (-0.1 dB) Passband Ripple Stopband Stopband Attenuation Total Group Delay (Fs = Output Sample Rate) tgd 0.5604 - - Fs 69 - - dB - 9/Fs - s 0 - 0.2604 Fs - - 0.025 dB Quad-Speed Mode Passband (-0.1 dB) Passband Ripple Stopband Stopband Attenuation Total Group Delay (Fs = Output Sample Rate) tgd 0.5000 - - Fs 60 - - dB - 5/Fs - s - 1 20 - Hz Hz - 10 - Deg - 0 dB High-Pass Filter Characteristics Frequency Response Phase Deviation -3.0 dB -0.13 dB (Note 9) @ 20 Hz (Note 9) Passband Ripple Filter Settling Time - 105/Fs s 8. Filter response is guaranteed by design. 9. Response shown is for Fs = 48 kHz. 10. Response is clock-dependent and will scale with Fs. Note that the response plots (Figures 13 to 24) are normalized to Fs and can be de-normalized by multiplying the X-axis scale by Fs. DS658F2 11 CS5345 PGAOUT ANALOG CHARACTERISTICS Test conditions (unless otherwise specified): AGND = DGND = 0 V; VA = 3.13 V to 5.25 V; VD = 3.13 V to 5.25 V or VA + 0.25 V, whichever is less; VLS = VLC = 1.71 V to 5.25 V; TA = -10 to +70 C for Commercial or -40 to +85 C for Automotive; Input test signal: 1 kHz sine wave; Measurement bandwidth: 10 Hz to 20 kHz; Fs = 48/96/192 kHz; Synchronous mode; All connections as shown in Figure 7 on page 22. VA = 4.75 V to 5.25 V Commercial Grade Parameter Symbol Min Typ Dynamic Performance with PGA Line-Level Input Selected Automotive Grade Max Min Typ Max Unit Dynamic Range PGA Setting: -12 dB to +6 dB A-weighted unweighted PGA Setting: +12 dB Gain A-weighted unweighted Total Harmonic Distortion + Noise (Note 11) PGA Setting: -12 dB to +6 dB -1 dB -20 dB -60 dB THD+N PGA Setting: +12 dB Gain -1 dB -20 dB -60 dB 98 95 104 101 - 96 93 104 101 - dB dB 92 89 98 95 - 90 87 98 95 - dB dB - -80 -81 -41 -74 - - -80 -81 -41 -72 - dB dB dB - -80 -75 -35 -74 - - -80 -75 -35 -72 - dB dB dB 77 74 83 80 - 75 72 83 80 - dB dB 65 62 71 68 - 63 60 71 68 - dB dB - -74 -60 -20 -68 - - -74 -60 -20 -66 - dB dB dB - -68 - - -68 - dB Dynamic Performance with PGA Mic-Level Input Selected Dynamic Range PGA Setting: -12 dB to 0 dB A-weighted unweighted PGA Setting: +12 dB A-weighted unweighted Total Harmonic Distortion + Noise (Note 11) PGA Setting: -12 dB to 0 dB -1 dB -20 dB THD+N -60 dB PGA Setting: +12 dB -1 dB 11. Referred to the typical Line-Level Full-Scale Input Voltage. 12 DS658F2 CS5345 PGAOUT ANALOG CHARACTERISTICS (Continued) VA = 3.13 V to 3.46 V Commercial Grade Parameter Symbol Min Typ Dynamic Performance with PGA Line-Level Input Selected Automotive Grade Max Min Typ Max Unit Dynamic Range PGA Setting: -12 dB to +6 dB A-weighted unweighted PGA Setting: +12 dB Gain A-weighted unweighted Total Harmonic Distortion + Noise (Note 11) PGA Setting: -12 dB to +6 dB -1 dB -20 dB -60 dB THD+N PGA Setting: +12 dB Gain -1 dB -20 dB -60 dB 93 90 101 98 - 91 88 101 98 - dB dB 89 86 95 92 - 87 84 95 92 - dB dB - -80 -78 -38 -74 - - -80 -78 -38 -72 - dB dB dB - -80 -72 -32 -74 - - -80 -72 -32 -72 - dB dB dB 77 74 83 80 - 75 72 83 80 - dB dB 65 62 71 68 - 63 60 71 68 - dB dB - -74 -60 -20 -68 - - -74 -60 -20 -66 - dB dB dB - -68 - - -68 - dB Dynamic Performance with PGA Mic Level-Input Selected Dynamic Range PGA Setting: -12 dB to 0 dB A-weighted unweighted PGA Setting: +12 dB A-weighted unweighted Total Harmonic Distortion + Noise (Note 11) PGA Setting: -12 dB to 0 dB -1 dB -20 dB THD+N -60 dB PGA Setting: +12 dB -1 dB DS658F2 13 CS5345 PGAOUT ANALOG CHARACTERISTICS (Continued) VA = 3.13 V to 5.25 V Parameter Symbol DC Accuracy with PGA Line Level Input Selected Interchannel Gain Mismatch Gain Error Gain Drift Commercial Grade Automotive Grade Min Typ Max Min Typ Max Unit - 0.1 5 100 - - 0.1 5 100 - dB % ppm/C - 0.3 5 300 - - 0.3 5 300 - dB % ppm/C -0.1dB 100 - 180 - 180 - +0.1dB 1 20 dB deg A k pF DC Accuracy with PGA Mic Level Input Selected Interchannel Gain Mismatch Gain Error Gain Drift Analog Output Frequency Response 10 Hz to 20 kHz Analog In to Analog Out Phase Shift DC Current draw from a PGAOUT pin AC-Load Resistance Load Capacitance (Note 12) IOUT RL CL +0.1dB -0.1dB 1 100 20 - 12. Guaranteed by design. 14 DS658F2 CS5345 DC ELECTRICAL CHARACTERISTICS AGND = DGND = 0 V, all voltages with respect to ground. MCLK=12.288 MHz; Fs=48 kHz; Master Mode. Parameter Symbol Min Typ Max Unit V V V V IA IA ID ID - 41 37 39 23 50 45 47 28 mA mA mA mA VA = 5 V VLS, VLC, VD=5 V IA ID - 0.50 0.54 - mA mA Power Consumption (Normal Operation) VA, VD, VLS, VLC = 5 V (Power-Down Mode) VA, VD, VLS, VLC = 3.3 V VA, VD, VLS, VLC = 5 V - - 400 198 4.2 485 241 - mW mW mW PSRR - 55 - dB VQ - 0.5 x VA - VDC IQ - - 1 A ZQ - 23 - k Power Supply Current (Normal Operation) VA = 5 VA = 3.3 VD, VLS, VLC = 5 VD, VLS, VLC = 3.3 Power Supply Current (Power-Down Mode) (Note 13) Power Supply Rejection Ratio (1 kHz) (Note 14) VQ Characteristics Quiescent Voltage DC Current from VQ VQ Output Impedance FILT+ Nominal Voltage Microphone Bias Voltage Current from MICBIAS (Note 15) FILT+ - VA - VDC MICBIAS - 0.8 x VA - VDC IMB - - 2 mA 13. Power-Down Mode is defines as RESET = Low with all clock and data lines held static and no analog input. 14. Valid with the recommended capacitor values on FILT+ and VQ as shown in the Typical Connection Diagram. 15. Guaranteed by design. The DC current draw represents the allowed current draw due to typical leakage through the electrolytic de-coupling capacitors. DS658F2 15 CS5345 DIGITAL INTERFACE CHARACTERISTICS Test conditions (unless otherwise specified): AGND = DGND = 0 V; VLS = VLC = 1.71 V to 5.25 V. Parameters (Note 16) Symbol Min Typ Max Units VIH VIH VIH VIH VIL VIL VOH VOH VOL VOL Iin 0.8xVLS 0.8xVLC 0.7xVLS 0.7xVLC VLS-1.0 VLC-1.0 - - 0.2xVLS 0.2xVLC 0.4 0.4 10 1 V V V V V V V V V V A pF - - s High-Level Input Voltage VL = 1.71 V VL > 2.0 V Low-Level Input Voltage High-Level Output Voltage at Io = 2 mA Low-Level Output Voltage at Io = 2 mA Input Leakage Current Input Capacitance Minimum OVFL Active Time Serial Port Control Port Serial Port Control Port Serial Port Control Port Serial Port Control Port Serial Port Control Port (Note 17) 6 10 ----------------LRCK 16. Serial Port signals include: MCLK, SCLK, LRCK, SDOUT. Control Port signals include: SCL/CCLK, SDA/CDOUT, AD0/CS, AD1/CDIN, RESET, INT, OVFL. 17. Guaranteed by design. 16 DS658F2 CS5345 SWITCHING CHARACTERISTICS - SERIAL AUDIO PORT Logic `0' = DGND = AGND = 0 V; Logic `1' = VL, CL = 20 pF. (Note 18) Parameter Sample Rate Single-Speed Mode Double-Speed Mode Quad-Speed Mode Symbol Min Typ Max Unit Fs Fs Fs 4 50 100 - 50 100 200 kHz kHz kHz fmclk tclkhl 1.024 8 - 51.200 - MHz ns tslr tsdo -10 0 50 50 - 10 36 % % ns ns 40 50 60 % - - ns - - ns MCLK Specifications MCLK Frequency MCLK Input Pulse Width High/Low Master Mode LRCK Duty Cycle SCLK Duty Cycle SCLK falling to LRCK edge SCLK falling to SDOUT valid Slave Mode LRCK Duty Cycle SCLK Period 9 Single-Speed Mode tsclkw 10 --------------------( 128 )Fs Double-Speed Mode tsclkw 10 -----------------( 64 )Fs Quad-Speed Mode tsclkw 10 -----------------( 64 )Fs - - ns tsclkh tsclkl tslr tsdo 30 48 -10 0 - 10 36 ns ns ns ns 9 9 SCLK Pulse Width High SCLK Pulse Width Low SCLK falling to LRCK edge SCLK falling to SDOUT valid 18. See Figure 1 and Figure 2 on page 18. DS658F2 17 CS5345 LRCK Output t slr SCLK Output t sdo SDOUT Figure 1. Master Mode Serial Audio Port Timing LRCK Input t slr t sclkh t sclkl SCLK Input t sdo t sclkw SDOUT Figure 2. Slave Mode Serial Audio Port Timing 18 DS658F2 CS5345 Channel B - Right Channel A - Left LRCK SCLK SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB Figure 3. Format 0, Left-Justified up to 24-Bit Data Channel A - Left LRCK Channel B - Right SCLK SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB Figure 4. Format 1, IS up to 24-Bit Data DS658F2 19 CS5345 SWITCHING CHARACTERISTICS - CONTROL PORT - IC FORMAT Inputs: Logic 0 = DGND = AGND = 0 V, Logic 1 = VLC, CL = 30 pF. Parameter Symbol Min Max Unit SCL Clock Frequency fscl - 100 kHz RESET Rising Edge to Start tirs 500 - ns Bus Free Time Between Transmissions tbuf 4.7 - s Start Condition Hold Time (prior to first clock pulse) thdst 4.0 - s Clock Low time tlow 4.7 - s Clock High Time thigh 4.0 - s tsust 4.7 - s thdd 0 - s tsud 250 - ns - 1 s Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling (Note 19) SDA Setup time to SCL Rising Rise Time of SCL and SDA (Note 20) trc, trd Fall Time SCL and SDA (Note 20) tfc, tfd - 300 ns Setup Time for Stop Condition tsusp 4.7 - s Acknowledge Delay from SCL Falling tack 300 1000 ns 19. Data must be held for sufficient time to bridge the transition time, tfc, of SCL. 20. Guaranteed by design. RST t irs Stop R e p e ate d Sta rt Sta rt t rd t fd Stop SDA t buf t t hdst t high t fc hdst t susp SCL t lo w t hdd t sud t ack t sust t rc Figure 5. Control Port Timing - IC Format 20 DS658F2 CS5345 SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT Inputs: Logic 0 = DGND = AGND = 0 V, Logic 1 = VLC, CL = 30 pF. Parameter Symbol Min Max Units CCLK Clock Frequency fsck - 6.0 MHz RESET Rising Edge to CS Falling tsrs 500 - ns CS High Time Between Transmissions tcsh 1.0 - s CS Falling to CCLK Edge tcss 20 - ns CCLK Low Time tscl 66 - ns CCLK High Time tsch 66 - ns CDIN to CCLK Rising Setup Time tdsu 40 - ns CCLK Rising to DATA Hold Time tdh 15 - ns CCLK Falling to CDOUT Stable (Note 21) tpd - 50 ns Rise Time of CDOUT tr1 - 25 ns Fall Time of CDOUT tf1 - 25 ns Rise Time of CCLK and CDIN (Note 22) tr2 - 100 ns Fall Time of CCLK and CDIN (Note 22) tf2 - 100 ns 21. Data must be held for sufficient time to bridge the transition time of CCLK. 22. For fsck <1 MHz. t srs RST CS t scl t css t sch t csh CCLK t r2 t f2 CDIN t dsu t dh t pd CDOUT Figure 6. Control Port Timing - SPI Format DS658F2 21 CS5345 3. TYPICAL CONNECTION DIAGRAM +3.3V to +5V 10 F 0.1 F 0.1 F VA VD +1.8V to +5V 0.1 F 0.1 F +3.3V to +5V 10 F VA 3.3 F PGAOUTA VLS 3.3 F PGAOUTB MCLK SCLK Digital Audio Capture AIN1A LRCK 1800 pF * SDOUT AIN1B INT OVFL CS5345 AIN2A SCL/CCLK AIN2B SDA/CDOUT AIN3A AD1/CDIN AD0/CS 2 k 2 k See Note 1 AIN3B VLC AIN4A/MICIN1 0.1 F AIN4B/MICIN2 AIN5A NC NC NC NC NC Note 1: Resistors are required for IC control port operation Note 2 The value of RL is dictated by the microphone carteridge. AIN5B AIN6A TSTI TSTO TSTO TSTO AIN6B * 1800 pF * RESET MicroController +1.8V to +5V 1800 pF 1800 pF * 1800 pF * 1800 pF * 1800 pF * 1800 pF * 1800 pF * 1800 pF * 1800 pF * 1800 pF * 10 F 0.1 F 47 F AGND AGND 0.1 F DGND 10 F 100 k 100 Right Analog Input 1 Left Analog Input 2 10 F 100 100 k 10 F 100 k 100 Right Analog Input 2 Left Analog Input 3 10 F 100 100 k 10 F 100 k 100 Right Analog Input 3 Left Analog Input 4 10 F 100 100 k 10 F 100 k 100 Right Analog Input 4 Left Analog Input 5 10 F 100 100 k 10 F 100 k 100 Right Analog Input 5 Left Analog Input 6 10 F 100 100 k 10 F 100 k 47 F * AFILTA AFILTB AGND 100 k 100 Right Analog Input 6 See Note 2 MICBIAS VQ FILT+ Left Analog Input 1 10 F 100 RL * 2.2nF 2.2nF * Capacitors must be C0G or equivalent Figure 7. Typical Connection Diagram 22 DS658F2 CS5345 4. APPLICATIONS 4.1 Recommended Power-Up Sequence 1. Hold RESET low until the power supply,MCLK, and LRCK are stable. In this state, the Control Port is reset to its default settings. 2. Bring RESET high. The device will remain in a low power state with the PDN bit set by default. The control port will be accessible. 3. The desired register settings can be loaded while the PDN bit remains set. 4. Clear the PDN bit to initiate the power-up sequence. 4.2 System Clocking The CS5345 will operate at sampling frequencies from 4 kHz to 200 kHz. This range is divided into three speed modes as shown in Table 1. Mode Sampling Frequency Single-Speed 4-50 kHz Double-Speed 50-100 kHz Quad-Speed 100-200 kHz Table 1. Speed Modes 4.2.1 Master Clock MCLK/LRCK must maintain an integer ratio as shown in Table 2. The LRCK frequency is equal to Fs, the frequency at which audio samples for each channel are clocked out of the device. The FM bits (See "Functional Mode (Bits 7:6)" on page 32.) and the MCLK Freq bits (See "MCLK Frequency - Address 05h" on page 33.) configure the device to generate the proper clocks in Master Mode and receive the proper clocks in Slave Mode. Table 2 illustrates several standard audio sample rates and the required MCLK and LRCK frequencies. LRCK (kHz) MCLK (MHz) 64x 96x 128x 192x 256x 384x 512x 768x 1024x 32 - - - - 8.1920 12.2880 16.3840 24.5760 32.7680 44.1 - - - - 11.2896 16.9344 22.5792 33.8680 45.1584 48 - - - - 12.2880 18.4320 24.5760 36.8640 49.1520 64 - - 8.1920 12.2880 16.3840 24.5760 32.7680 - - 88.2 - - 11.2896 16.9344 22.5792 33.8680 45.1584 - - 96 - - 12.2880 18.4320 24.5760 36.8640 49.1520 - - 128 8.1920 12.2880 16.3840 24.5760 32.7680 - - - - 176.4 11.2896 16.9344 22.5792 33.8680 45.1584 - - - - 192 12.2880 18.4320 24.5760 36.8640 49.1520 - - - Mode QSM DSM SSM Table 2. Common Clock Frequencies DS658F2 23 CS5345 4.2.2 Master Mode As a clock master, LRCK and SCLK will operate as outputs. LRCK and SCLK are internally derived from MCLK with LRCK equal to Fs and SCLK equal to 64 x Fs as shown in Figure 8. MCLK Freq Bits MCLK /1 000 /1.5 001 /2 010 /3 011 /4 100 /256 00 /128 01 /64 10 LRCK FM Bits /4 00 /2 01 /1 10 SCLK Figure 8. Master Mode Clocking 4.2.3 Slave Mode In Slave Mode, SCLK and LRCK operate as inputs. The Left/Right clock signal must be equal to the sample rate, Fs, and must be synchronously derived from the supplied master clock, MCLK. The serial bit clock, SCLK, must be synchronously derived from the master clock, MCLK, and be equal to 128x, 64x, 48x or 32x Fs, depending on the desired speed mode. Refer to Table 3 for required clock ratios. SCLK/LRCK Ratio Single-Speed Double-Speed Quad-Speed 32x, 48x, 64x, 128x 32x, 48x, 64x 32x, 48x, 64x Table 3. Slave Mode Serial Bit Clock Ratios 4.3 High-Pass Filter and DC Offset Calibration When using operational amplifiers in the input circuitry driving the CS5345, a small DC offset may be driven into the A/D converter. The CS5345 includes a high-pass filter after the decimator to remove any DC offset which could result in recording a DC level, possibly yielding clicks when switching between devices in a multichannel system. The high-pass filter continuously subtracts a measure of the DC offset from the output of the decimation filter. If the HPFFreeze bit (See "High-Pass Filter Freeze (Bit 1)" on page 32.) is set during normal operation, the current value of the DC offset for the each channel is frozen and this DC offset will continue to be subtracted from the conversion result. This feature makes it possible to perform a system DC offset calibration by: 1. Running the CS5345 with the high-pass filter enabled until the filter settles. See the Digital Filter Characteristics section for filter settling time. 2. Disabling the high-pass filter and freezing the stored DC offset. A system calibration performed in this way will eliminate offsets anywhere in the signal path between the calibration point and the CS5345. 24 DS658F2 CS5345 4.4 Analog Input Multiplexer, PGA, and Mic Gain The CS5345 contains a stereo 6-to-1 analog input multiplexer followed by a programmable gain amplifier (PGA). The input multiplexer can select one of six possible stereo analog input sources and route it to the PGA. Analog inputs 4A and 4B are able to insert a +32 dB gain stage before the input multiplexer, allowing them to be used for microphone-level signals without the need for any external gain. The PGA stage provides 12 dB of gain or attenuation in 0.5 dB steps. Figure 9 shows the architecture of the input multiplexer, PGA, and microphone gain stages. AIN1A AIN2A AIN3A AIN4A/MICIN1 MUX PGA Out to ADC Channel A +32 dB AIN5A AIN6A Channel A PGA Gain Bits Analog Input Selection Bits AIN1B AIN2B Channel B PGA Gain Bits AIN3B AIN4B/MICIN2 MUX PGA Out to ADC Channel B +32 dB AIN5B AIN6B Figure 9. Analog Input Architecture The ""Analog Input Selection (Bits 2:0)" on page 35" outlines the bit settings necessary to control the input multiplexer and mic gain. "Channel B PGA Control - Address 07h" on page 33 and "Channel A PGA Control - Address 08h" on page 34 outline the register settings necessary to control the PGA. By default, linelevel input 1 is selected, and the PGA is set to 0 dB. 4.5 Input Connections The analog modulator samples the input at 6.144 MHz (MCLK=12.288 MHz). The digital filter will reject signals within the stopband of the filter. However, there is no rejection for input signals which are (n x 6.144 MHz) the digital passband frequency, where n=0,1,2,... Refer to the Typical Connection Diagram for the recommended analog input circuit that will attenuate noise energy at 6.144 MHz. The use of capacitors which have a large voltage coefficient (such as general-purpose ceramics) must be avoided since these can degrade signal linearity. Any unused analog input pairs should be left unconnected. 4.6 PGA Auxiliary Analog Output The CS5345 includes an auxiliary analog output through the PGAOUT pins. These pins can be configured to output the analog input to the ADC as selected by the input MUX and gained or attenuated with the PGA, or alternatively, they may be set to high-impedance. See the ""PGAOut Source Select (Bit 6)" on page 33" for information on configuring the PGA auxiliary analog output. The PGA auxiliary analog output can source very little current. As current from the PGAOUT pins increases, distortion will increase. For this reason, a high-input impedance buffer must be used on the PGAOUT pins to achieve full performance. Refer to the table in "PGAOUT Analog Characteristics" on page 12 for acceptable loading conditions. DS658F2 25 CS5345 4.7 Control Port Description and Timing The control port is used to access the registers, allowing the CS5345 to be configured for the desired operational modes and formats. The operation of the control port may be completely asynchronous with respect to the audio sample rates. However, to avoid potential interference problems, the control port pins should remain static if no operation is required. The control port has two modes: SPI and IC, with the CS5345 acting as a slave device. SPI Mode is selected if there is a high-to-low transition on the AD0/CS pin, after the RESET pin has been brought high. IC Mode is selected by connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently selecting the desired AD0 bit address state. 4.7.1 SPI Mode In SPI Mode, CS is the CS5345 chip-select signal; CCLK is the control port bit clock (input into the CS5345 from the microcontroller); CDIN is the input data line from the microcontroller; CDOUT is the output data line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling edge. Figure 10 shows the operation of the control port in SPI Mode. To write to a register, bring CS low. The first seven bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indicator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP), which is set to the address of the register that is to be updated. The next eight bits are the data that will be placed into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z state. It may be externally pulled high or low with a 47 k resistor, if desired. To read a register, the MAP has to be set to the correct address by executing a partial write cycle which finishes (CS high) immediately after the MAP byte. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W) high. The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave the high-impedance state). For both read and write cycles, the memory address pointer will automatically increment following each data byte in order to facilitate block reads and writes of successive registers. CS CC LK C H IP ADDRESS 1001111 C D IN MAP MSB R/W C H IP ADDRESS DATA b y te 1 LSB 1001111 R/W b y te n High Impedance CDOUT MSB LSB MSB LSB MAP = Memory Address Pointer, 8 bits, MSB first Figure 10. Control Port Timing in SPI Mode 4.7.2 IC Mode In IC Mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL. There is no CS pin. Pins AD0 and AD1 form the two least-significant bits of the chip address and should 26 DS658F2 CS5345 be connected through a resistor to VLC or DGND as desired. The state of the pins is sensed while the CS5345 is being reset. The signal timings for a read and write cycle are shown in Figure 11 and Figure 12. A Start condition is defined as a falling transition of SDA while the clock is high. A Stop condition is a rising transition while the clock is high. All other transitions of SDA occur while the clock is low. The first byte sent to the CS5345 after a Start condition consists of a 7-bit chip address field and a R/W bit (high for a read, low for a write). The upper 5 bits of the 7-bit address field are fixed at 10011. To communicate with a CS5345, the chip address field, which is the first byte sent to the CS5345, should match 10011 followed by the settings of the AD1 and AD0. The eighth bit of the address is the R/W bit. If the operation is a write, the next byte is the Memory Address Pointer (MAP) which selects the register to be read or written. If the operation is a read, the contents of the register pointed to by the MAP will be output. Following each data byte, the memory address pointer will automatically increment to facilitate block reads and writes of successive registers. Each byte is separated by an acknowledge bit. The ACK bit is output from the CS5345 after each input byte is read, and is input to the CS5345 from the microcontroller after each transmitted byte. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 24 25 26 27 28 SCL CHIP ADDRESS (WRITE) 1 SDA 0 0 1 MAP BYTE 1 AD1 AD0 0 6 6 5 4 3 2 1 0 7 ACK 6 ACK 1 DATA +n DATA +1 DATA 0 7 6 1 0 7 6 1 0 ACK ACK STOP START Figure 11. Control Port Timing, IC Write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCL CHIP ADDRESS (WRITE) SDA 1 0 0 1 STOP MAP BYTE 7 1 AD1 AD0 0 6 5 4 3 ACK 2 1 CHIP ADDRESS (READ) 1 0 0 0 1 ACK START DATA 1 AD1 AD0 1 START 7 ACK DATA +1 0 7 ACK 0 DATA + n 7 0 NO ACK STOP Figure 12. Control Port Timing, IC Read Since the read operation cannot set the MAP, an aborted write operation is used as a preamble. As shown in Figure 12, the write operation is aborted after the acknowledge for the MAP byte by sending a stop condition. The following pseudocode illustrates an aborted write operation followed by a read operation. Send start condition. Send 10011xx0 (chip address & write operation). Receive acknowledge bit. Send MAP byte. Receive acknowledge bit. Send stop condition, aborting write. Send start condition. Send 10011xx1(chip address & read operation). Receive acknowledge bit. DS658F2 27 CS5345 Receive byte, contents of selected register. Send acknowledge bit. Send stop condition. 4.8 Interrupts and Overflow The CS5345 has a comprehensive interrupt capability. The INT output pin is intended to drive the interrupt input pin on the host microcontroller. The INT pin may function as either an active high CMOS driver or an active low open-drain driver (see "Active High/Low (Bit 0)" on page 35). When configured as active low open-drain, the INT pin has no active pull-up transistor, allowing it to be used for wired-OR hook-ups with multiple peripherals connected to the microcontroller interrupt input pin. In this configuration, an external pull-up resistor must be placed on the INT pin for proper operation. Many conditions can cause an interrupt, as listed in the interrupt status register descriptions (see "Interrupt Status - Address 0Dh" on page 35). Each source may be masked off through mask register bits. In addition, each source may be set to rising edge, falling edge, or level-sensitive. Combined with the option of levelsensitive or edge-sensitive modes within the microcontroller, many different configurations are possible, depending on the needs of the equipment designer. The CS5345 also has a dedicated overflow output. The OVFL pin functions as active low open drain and has no active pull-up transistor, thereby requiring an external pull-up resistor. The OVFL pin outputs an OR of the ADCOverflow and ADCUnderflow conditions available in the Interrupt Status register; however, these conditions do not need to be unmasked for proper operation of the OVFL pin. 4.9 Reset When RESET is low, the CS5345 enters a low-power mode and all internal states are reset, including the control port and registers, the outputs are muted. When RESET is high, the control port becomes operational, and the desired settings should be loaded into the control registers. Writing a 0 to the PDN bit in the Power Control register will then cause the part to leave the low-power state and begin operation. The delta-sigma modulators settle in a matter of microseconds after the analog section is powered, either through the application of power or by setting the RESET pin high. However, the voltage reference will take much longer to reach a final value due to the presence of external capacitance on the FILT+ pin. During this voltage reference ramp delay, SDOUT will be automatically muted. It is recommended that RESET be activated if the analog or digital supplies drop below the recommended operating condition to prevent power-glitch-related issues. 4.10 Synchronization of Multiple Devices In systems where multiple ADCs are required, care must be taken to achieve simultaneous sampling. To ensure synchronous sampling, the master clocks and left/right clocks must be the same for all of the CS5345s in the system. If only one master clock source is needed, one solution is to place one CS5345 in Master Mode, and slave all of the other CS5345s to the one master. If multiple master clock sources are needed, a possible solution would be to supply all clocks from the same external source and time the CS5345 reset with the inactive edge of master clock. This will ensure that all converters begin sampling on the same clock edge. 4.11 Grounding and Power Supply Decoupling As with any high-resolution converter, the CS5345 requires careful attention to power supply and grounding arrangements if its potential performance is to be realized. Figure 7 shows the recommended power arrangements, with VA connected to a clean supply. VD, which powers the digital filter, may be run from the 28 DS658F2 CS5345 system logic supply (VLS or VLC) or may be powered from the analog supply (VA) via a resistor. In this case, no additional devices should be powered from VD. Power supply decoupling capacitors should be as near to the CS5345 as possible, with the low value ceramic capacitor being the nearest. All signals, especially clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted coupling into the modulators. The FILT+ and VQ decoupling capacitors, particularly the 0.1 F, must be positioned to minimize the electrical path from FILT+ and AGND. The CS5345 evaluation board demonstrates the optimum layout and power supply arrangements. To minimize digital noise, connect the CS5345 digital outputs only to CMOS inputs. DS658F2 29 CS5345 5. REGISTER QUICK REFERENCE This table shows the register names and their associated default values. Addr Function 01h Chip ID 02h Power Control 7 6 5 4 3 2 1 0 PART3 PART2 PART1 PART0 REV3 REV2 REV1 REV0 1 1 1 0 0 0 0 1 Reserved PDN_MIC PDN_ADC Reserved PDN 0 0 0 0 1 Reserved Reserved Reserved Reserved Reserved Freeze 0 03h Reserved Reserved Reserved 0 0 Reserved Reserved Reserved 0 0 0 0 1 0 0 0 FM1 FM0 Reserved DIF Reserved Mute HPFFreeze M/S 0 0 0 0 0 0 0 0 Reserved MCLK Freq2 MCLK Freq1 MCLK Freq0 Reserved Reserved Reserved Reserved 0 0 0 0 0 0 0 0 06h PGAOut Control Reserved PGAOut Reserved Reserved Reserved Reserved Reserved Reserved 0 1 07h PGA Ch B Gain Control Reserved Reserved 08h PGA Ch A Gain Control Reserved Reserved 04h ADC Control 05h MCLK Frequency 0 0 09h Analog Input Control 0 0 0 0 0 0 0 0 Gain5 Gain4 Gain3 Gain2 Gain1 Gain0 0 0 0 0 0 0 Gain5 Gain4 Gain3 Gain2 Gain1 Gain0 0 0 0 0 0 0 PGASoft PGAZero Sel2 Sel1 Sel0 1 1 0 0 1 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 0 0 0 0Ah - Reserved 0Bh Reserved Reserved Reserved 0Ch Active Level Control Reserved Reserved Reserved 0 1 0 1 0 0 0Dh Interrupt Status Reserved Reserved Reserved 0 0 0 0Eh Interrupt Mask Reserved Reserved Reserved 0Fh Interrupt Mode MSB Reserved Reserved Reserved 0 0 10h Interrupt Mode LSB 0 0 0 Reserved Reserved Reserved 0 30 0 0 0 0 0 0 0 0 Reserved Reserved Reserved Reserved Active_H/L 0 0 0 0 0 Reserved ClkErr Reserved Ovfl Undrfl 0 0 0 0 0 Reserved ClkErrM Reserved OvflM UndrflM 0 0 0 0 0 Reserved ClkErr1 Reserved Ovfl1 Undrfl1 0 0 0 0 0 Reserved ClkErr0 Reserved Ovfl0 Undrfl0 0 0 0 0 0 DS658F2 CS5345 6. REGISTER DESCRIPTION 6.1 Chip ID - Register 01h 7 PART3 6 PART2 5 PART1 4 PART0 3 REV3 2 REV2 1 REV1 0 REV0 Function: This register is Read-Only. Bits 7 through 4 are the part number ID, which is 1110b (0Eh), and the remaining bits (3 through 0) indicate the device revision as shown in Table 4 below. REV[2:0] Revision 001 A 010 B, C0 011 C1 Table 4. Device Revision 6.2 Power Control - Address 02h 7 Freeze 6.2.1 6 Reserved 5 Reserved 4 Reserved 3 PDN_MIC 2 PDN_ADC 1 Reserved 0 PDN Freeze (Bit 7) Function: This function allows modifications to be made to certain control port bits without the changes taking effect until the Freeze bit is disabled. To make multiple changes to these bits take effect simultaneously, set the Freeze bit, make all changes, then clear the Freeze bit. The bits affected by the Freeze function are listed in Table 5. Name Register Bit(s) Mute 04h 2 Gain[5:0] 07h 5:0 Gain[5:0] 08h 5:0 Table 5. Freeze-able Bits 6.2.2 Power-Down MIC (Bit 3) Function: The microphone preamplifier block will enter a low-power state whenever this bit is set. 6.2.3 Power-Down ADC (Bit 2) Function: The ADC pair will remain in a reset state whenever this bit is set. 6.2.4 Power-Down Device (Bit 0) Function: The device will enter a low-power state whenever this bit is set. The power-down bit is set by default and must be cleared before normal operation can occur. The contents of the control registers are retained when the device is in power-down. DS658F2 31 CS5345 6.3 ADC Control - Address 04h 7 6 5 4 3 2 1 0 FM1 FM0 Reserved DIF Reserved Mute HPFFreeze M/S 6.3.1 Functional Mode (Bits 7:6) Function: Selects the required range of sample rates. FM1 FM0 0 0 Single-Speed Mode: 4 to 50 kHz sample rates Mode 0 1 Double-Speed Mode: 50 to 100 kHz sample rates 1 0 Quad-Speed Mode: 100 to 200 kHz sample rates 1 1 Reserved Table 6. Functional Mode Selection 6.3.2 Digital Interface Format (Bit 4) Function: The required relationship between LRCK, SCLK and SDOUT is defined by the Digital Interface Format bit. The options are detailed in Table 7 and may be seen in Figure 3 and Figure 4. DIF Description Format Figure 0 Left-Justified, up to 24-bit data (default) 0 3 1 IS, up to 24-bit data 1 4 Table 7. Digital Interface Formats 6.3.3 Mute (Bit 2) Function: When this bit is set, the serial audio output of the both channels is muted. 6.3.4 High-Pass Filter Freeze (Bit 1) Function: When this bit is set, the internal high-pass filter is disabled.The current DC offset value will be frozen and continue to be subtracted from the conversion result. See "High-Pass Filter and DC Offset Calibration" on page 24. 6.3.5 Master / Slave Mode (Bit 0) Function: This bit selects either master or slave operation for the serial audio port. Setting this bit selects Master Mode, while clearing this bit selects Slave Mode. 32 DS658F2 CS5345 6.4 MCLK Frequency - Address 05h 7 Reserved 6.4.1 6 MCLK Freq2 5 MCLK Freq1 4 MCLK Freq0 3 2 1 0 Reserved Reserved Reserved Reserved Master Clock Dividers (Bits 6:4) Function: Sets the frequency of the supplied MCLK signal. See Table 8 for the appropriate settings. MCLK Divider MCLK Freq2 MCLK Freq1 MCLK Freq0 /1 0 0 0 / 1.5 0 0 1 /2 0 1 0 /3 0 1 1 /4 1 0 0 Reserved 1 0 1 Reserved 1 1 x Table 8. MCLK Frequency 6.5 PGAOut Control - Address 06h 7 6 5 4 3 2 1 0 Reserved PGAOut Reserved Reserved Reserved Reserved Reserved Reserved 6.5.1 PGAOut Source Select (Bit 6) Function: This bit is used to configure the PGAOut pins to be either high impedance or PGA outputs. Refer to Table 9. PGAOut PGAOutA & PGAOutB 0 High Impedance 1 PGA Output Table 9. PGAOut Source Selection 6.6 Channel B PGA Control - Address 07h 7 Reserved 6.6.1 6 Reserved 5 Gain5 4 Gain4 3 Gain3 2 Gain2 1 Gain1 0 Gain0 Channel B PGA Gain (Bits 5:0) Function: See "Channel A PGA Gain (Bits 5:0)" on page 34. DS658F2 33 CS5345 6.7 Channel A PGA Control - Address 08h 7 Reserved 6.7.1 6 Reserved 5 Gain5 4 Gain4 3 Gain3 2 Gain2 1 Gain1 0 Gain0 Channel A PGA Gain (Bits 5:0) Function: Sets the gain or attenuation for the ADC input PGA stage. The gain may be adjusted from -12 dB to +12 dB in 0.5 dB steps. The gain bits are in two's complement with the Gain0 bit set for a 0.5 dB step. Register settings outside of the 12 dB range are reserved and must not be used. See Table 10 for example settings. Gain[5:0] Setting 101000 -12 dB 000000 0 dB 011000 +12 dB Table 10. Example Gain and Attenuation Settings 6.8 ADC Input Control - Address 09h 7 Reserved 6.8.1 6 Reserved 5 Reserved 4 PGASoft 3 PGAZero 2 Sel2 1 Sel1 0 Sel0 PGA Soft Ramp or Zero Cross Enable (Bits 4:3) Function: Soft Ramp Enable Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally ramping, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock periods. See Table 11. Zero Cross Enable Zero Cross Enable dictates that signal-level changes, either by attenuation changes or muting, will occur on a signal zero crossing to minimize audible artifacts. The requested level change will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel. See Table 11. Soft Ramp and Zero Cross Enable Soft Ramp and Zero Cross Enable dictate that signal-level changes, either by attenuation changes or muting, will occur in 1/8 dB steps and be implemented on a signal zero crossing. The 1/8 dB level change will occur after a time-out period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel. See Table 11. 34 DS658F2 CS5345 PGASoft 0 0 1 1 PGAZeroCross 0 1 0 1 Mode Changes to affect immediately Zero Cross enabled Soft Ramp enabled Soft Ramp and Zero Cross enabled (default) Table 11. PGA Soft Cross or Zero Cross Mode Selection 6.8.2 Analog Input Selection (Bits 2:0) Function: These bits are used to select the input source for the PGA and ADC. Please see Table 12. Sel2 Sel1 Sel0 PGA/ADC Input 0 0 0 Microphone-Level Inputs (+32 dB Gain Enabled) 0 0 1 Line-Level Input Pair 1 0 1 0 Line-Level Input Pair 2 0 1 1 Line-Level Input Pair 3 1 0 0 Line-Level Input Pair 4 1 0 1 Line-Level Input Pair 5 1 1 0 Line-Level Input Pair 6 1 1 1 Reserved Table 12. Analog Input Multiplexer Selection 6.9 Active Level Control - Address 0Ch 7 6 5 4 3 2 1 0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Active_H/L Active High/Low (Bit 0) 6.9.1 Function: When this bit is set, the INT pin functions as an active high CMOS driver. When this bit is cleared, the INT pin functions as an active low open drain driver and will require an external pull-up resistor for proper operation. 6.10 Interrupt Status - Address 0Dh 7 Reserved 6 Reserved 5 Reserved 4 Reserved 3 ClkErr 2 Reserved 1 Ovfl 0 Undrfl For all bits in this register, a `1' means the associated interrupt condition has occurred at least once since the register was last read. A `0' means the associated interrupt condition has NOT occurred since the last reading of the register. Status bits that are masked off in the associated mask register will always be `0' in this register. This register defaults to 00h. DS658F2 35 CS5345 6.10.1 Clock Error (Bit 3) Function: Indicates the occurrence of a clock error condition. 6.10.2 Overflow (Bit 1) Function: Indicates the occurrence of an ADC overflow condition. 6.10.3 Underflow (Bit 0) Function: Indicates the occurrence of an ADC underflow condition. 6.11 Interrupt Mask - Address 0Eh 7 Reserved 6 Reserved 5 Reserved 4 Reserved 3 ClkErrM 2 Reserved 1 OvflM 0 UndrflM Function: The bits of this register serve as a mask for the Status sources found in the register "Interrupt Status - Address 0Dh" on page 35. If a mask bit is set to 1, the error is unmasked, meaning that its occurrence will affect the INT pin and the status register. If a mask bit is set to 0, the error is masked, meaning that its occurrence will not affect the INT pin or the status register. The bit positions align with the corresponding bits in the Status register. 6.12 Interrupt Mode MSB - Address 0Fh 6.13 Interrupt Mode LSB - Address 10h 7 Reserved Reserved 6 Reserved Reserved 5 Reserved Reserved 4 Reserved Reserved 3 ClkErr1 ClkErr0 2 Reserved Reserved 1 Ovfl1 Ovfl0 0 Undrfl1 Undrfl0 Function: The two Interrupt Mode registers form a 2-bit code for each Interrupt Status register function. There are three ways to set the INT pin active in accordance with the interrupt condition. In the Rising-Edge Active Mode, the INT pin becomes active on the arrival of the interrupt condition. In the Falling-Edge Active Mode, the INT pin becomes active on the removal of the interrupt condition. In Level-Active Mode, the INT pin remains active during the interrupt condition. 00 - Rising edge active 01 - Falling edge active 10 - Level active 11 - Reserved 36 DS658F2 CS5345 7. PARAMETER DEFINITIONS Dynamic Range The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is added to resulting measurement to refer the measurement to full scale. This technique ensures that the distortion components are below the noise level and do not affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Expressed in decibels. Total Harmonic Distortion + Noise The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured at -1 and -20 dBFS as suggested in AES17-1991 Annex A. Frequency Response A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response at 1 kHz. Units in decibels. Interchannel Isolation A measure of crosstalk between the left and right channels. Measured for each channel at the converter's output with no signal to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch The gain difference between left and right channels. Units in decibels. Gain Drift The change in gain value with temperature. Units in ppm/C. DS658F2 37 CS5345 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 Amplitude (dB) Amplitude (dB) 8. FILTER PLOTS 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 0.40 0.42 0.44 Frequency (norm alized to Fs) 0 0.10 -1 0.08 -2 0.06 -3 0.04 -4 -5 -6 -7 0.58 0.60 0.00 -0.04 -0.06 -0.08 -0.10 0.46 0.47 0.48 0.49 0.5 0.51 0.52 0.53 0.54 0 0.55 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Figure 16. Single-Speed Passband Ripple Amplitude (dB) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 0.1 0.05 Frequency (norm alized to Fs) Figure 15. Single-Speed Transition Band (Detail) Amplitude (dB) 0.56 -0.02 -9 Frequency (norm alized to Fs) 0.9 Frequency (norm alized to Fs) Figure 17. Double-Speed Stopband Rejection 38 0.54 0.02 -8 0.0 0.52 Figure 14. Single-Speed Stopband Rejection Amplitude (dB) Amplitude (dB) Figure 13. Single-Speed Stopband Rejection -10 0.45 0.46 0.48 0.50 Frequency (norm alized to Fs) 1.0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 0.40 0.42 0.44 0.46 0.48 0.50 0.52 0.54 0.56 0.58 0.60 Frequency (norm alized to Fs) Figure 18. Double-Speed Stopband Rejection DS658F2 0 0.10 -1 0.08 -2 0.06 -3 0.04 Amplitude (dB) Amplitude (dB) CS5345 -4 -5 -6 -7 0.02 0.00 -0.02 -0.04 -8 -0.06 -9 -0.08 -10 0.46 0.47 0.48 0.49 0.50 0.51 -0.10 0.00 0.05 0.52 Frequency (norm alized to Fs) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 Figure 20. Double-Speed Passband Ripple Amplitude (dB) Amplitude (dB) Figure 19. Double-Speed Transition Band (Detail) 0.0 0.10 Frequency (norm alized to Fs) 0.9 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 1.0 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 Frequency (norm alized to Fs) Frequency (norm alized to Fs) Figure 21. Quad-Speed Stopband Rejection Figure 22. Quad-Speed Stopband Rejection 0 0.10 -1 0.08 -3 0.06 -4 0.04 Amplitude (dB) Amplitude (dB) -2 -5 -6 -7 -8 -0.04 -0.08 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 Frequency (norm alized to Fs) Figure 23. Quad-Speed Transition Band (Detail) DS658F2 0.00 -0.02 -0.06 -9 -10 0.10 0.02 -0.10 0.00 0.03 0.05 0.08 0.10 0.13 0.15 0.18 0.20 0.23 0.25 0.28 Frequency (norm alized to Fs) Figure 24. Quad-Speed Passband Ripple 39 CS5345 9. PACKAGE DIMENSIONS 48L LQFP PACKAGE DRAWING E E1 D D1 1 e B A A1 L DIM A A1 B D D1 E E1 e* L MIN --0.002 0.007 0.343 0.272 0.343 0.272 0.016 0.018 0.000 * Nominal pin pitch is 0.50 mm INCHES NOM MAX MIN 0.055 0.063 --0.004 0.006 0.05 0.009 0.011 0.17 0.354 0.366 8.70 0.28 0.280 6.90 0.354 0.366 8.70 0.28 0.280 6.90 0.020 0.024 0.40 0.24 0.030 0.45 4 7.000 0.00 *Controlling dimension is mm. MILLIMETERS NOM MAX 1.40 1.60 0.10 0.15 0.22 0.27 9.0 BSC 9.30 7.0 BSC 7.10 9.0 BSC 9.30 7.0 BSC 7.10 0.50 BSC 0.60 0.60 0.75 4 7.00 *JEDEC Designation: MS022 10.THERMAL CHARACTERISTICS AND SPECIFICATIONS Parameters Package Thermal Resistance (Note 1) Allowable Junction Temperature 48-LQFP Symbol Min Typ Max Units JA JC - 48 15 - 125 C/Watt C/Watt C 1. JA is specified according to JEDEC specifications for multi-layer PCBs. 40 DS658F2 CS5345 11.ORDERING INFORMATION Product CS5345 CS5345 CDB5345 Description 24-bit, 192 kHz Stereo Audio ADC 24-bit, 192 kHz Stereo Audio ADC Package Pb-Free 48-LQFP 48-LQFP CS5345 Evaluation Board Yes Grade Commercial Temp Range -10 to +70 C Yes Automotive -40 to +105 C No - - Container Order # Tray CS5345-CQZ Tape & Reel CS5345-CQZR Tray CS5345-DQZ Tape & Reel CS5345-DQZR - CDB5345 12.REVISION HISTORY Release F1 F2 Changes - Removed the MAP auto-increment functional description from the Control Port Description and Timing section beginning on page 26. - Added device revision information to the Chip ID - Register 01h description on page 31. - Added Automotive Grade - Changed MCLK to input only in the Pin Descriptions table on page 5. - Updated the ADC Analog Characteristics table on page 8. - Updated the PGAOUT Analog Characteristics table on page 12. - Updated the DC Electrical Characteristics table on page 15. - Updated the Digital Interface Characteristics table on page 16. - Updated the Switching Characteristics - Serial Audio Port table on page 17. - Updated the Switching Characteristics - Control Port - SPI Format table on page 21. - Updated the Typical Connection Diagram on page 22. - Switched Channel B PGA Control - Address 07h on page 33 and Channel A PGA Control - Address 08h on page 34. Contacting Cirrus Logic Support For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find the one nearest you, go to www.cirrus.com IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, the Cirrus Logic logo designs, and Popguard are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. IC is a registered trademark of Philips Semiconductor. SPI is a trademark of Motorola, Inc. DS658F2 41