MCC SMAJ4728 THRU SMAJ4764 omponents 20736 Marilla Street Chatsworth !"# $ % !"# Features l Silicon For surface mount application (flat handing surface for 1 Watt Accurate placement) l 3.3 thru 100 Volt Voltage Range l High Surge Current Rating l Higher Voltages Available l Available on Tape and Reel Zener Diodes Mechanical Data l DO-214AC (SMAJ) (High Profile) CASE: JEDEC DO-214AC molded plastic body over passivated chip l Terminals solderable per MIL-STD-750, Method 2026 l Polarity is indicated by cathode band. l Maximum temperature for soldering: 260 C for 10 seconds. l For surface mount applications with flame retardent epoxy H Cathode Band o J Meeting UL94V-0 Maximum Ratings @ 25oC Unless Otherwise Specified Peak Surge IS See Table 1 Current Maximum VF 1.2V (Note: 1) Forward Voltage Steady State P(AV) 1.0W (Note: 2,3) Power Dissipation Operation And Storage Temperature TJ , TSTG -55o C to +150o C A E C D F B G DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 NOTE * SUGGESTED SOLDER PAD LAYOUT NOTES: 0.090" 1. Forward Current @ 200mA. 2. Mounted on 4.0mm copper pads to each terminal. 3. Lead temperature at 100 C or less. Derate linearly 2 o o 0.085" o above 100 C to zero power at 150 C. 0.070" Revision: 3 www.mccsemi.com 2003/04/30 MCC SMAJ4728 thru SMAJ4764 Electrical Characteristics @ 25oC Unless Otherwise Specified MCC PART NUMBER SMAJ4728 SMAJ4729 SMAJ4730 SMAJ4731 SMAJ4732 SMAJ4733 SMAJ4734 SMAJ4735 SMAJ4736 SMAJ4737 SMAJ4738 SMAJ4739 SMAJ4740 SMAJ4741 SMAJ4742 SMAJ4743 SMAJ4744 SMAJ4745 SMAJ4746 SMAJ4747 SMAJ4748 SMAJ4749 SMAJ4750 SMAJ4751 SMAJ4752 SMAJ4753 SMAJ4754 SMAJ4755 SMAJ4756 SMAJ4757 SMAJ4758 SMAJ4759 SMAJ4760 SMAJ4761 SMAJ4762 SMAJ4763 SMAJ4764 MAXIMUM REGULATOR MAXIMUM MAXIMUM MAXIMUM CURRENT TEST DYNAMIC REVERSE TEST KNEE ZENER Izm IMPEDANCE VOLTAGE CURRENT IMPEDANCE CURRENT VOLTAGE Ta=50oC Vr Ir @ Vr Zzt @ Izt Izt Zzk @ Izk Vz TEST CURRENT Izk MAXIMUM SURGE CURRENT Is VOLTS mA OHMS uA VOLTS mA OHMS MA mA 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 76 69 64 58 53 49 45 41 37 34 31 28 25 23 21 19 17 15.5 14 12.5 11.5 10.5 9.5 8.5 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.7 3.3 3.0 2.8 2.5 10 10 9 9 8 7 5 2 3.5 4.0 4.5 5.0 7 8 9 10 14 16 20 22 23 25 35 40 45 50 60 70 80 95 110 125 150 175 200 250 350 100 100 50 10 10 10 10 10 10 10 10 10 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 1 1 1 1 1 1 2 3 4 5 6 7 7.6 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8 38.8 42.6 47.1 51.7 56.0 62.2 69.2 76.0 276 252 234 217 193 178 162 146 133 121 110 100 91 83 76 69 61 57 50 45 41 38 34 30 27 25 23 22 19 18 16 14 13 12 11 10 9 400 400 400 400 500 550 600 700 700 700 700 700 700 700 700 700 700 700 750 750 750 750 750 1000 1000 1000 1000 1500 1500 1500 2000 2000 2000 2000 3000 3000 3000 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.5 0.5 0.5 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 1380 1260 1190 1070 970 890 810 730 660 605 550 500 454 414 380 344 304 285 250 225 205 190 170 150 135 125 115 110 95 90 80 70 65 60 55 50 45 NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage. No suffix signifies A 10% tolerance, C signifies 2%, and D signifies 1% tolerance. NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to 10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure a sharp knee on the breakdown curve and eliminate unstable units. NOTE 3 The reverse surge current is measured at 25oC ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second duration superimposed on Izt NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current. Revision: 3 www.mccsemi.com 2003/04/30 SMAJ4728 thru SMAJ4764 Ratings and Characteristic Curves (T A MCC = 25C unless otherwise noted) SMAJ4728... SMAJ4764 Revision: 3 www.mccsemi.com 2003/04/30