Supertex inc. HV2201 Low Charge Injection, 8-Channel, Enhanced, High Voltage Analog Switch Features General Description HVCMOS technology for high performance 8 Channels of high voltage analog switch 3.3 or 5.0V CMOS input logic level 20MHz data shift clock frequency Very low quiescent power dissipation (-10A) Low parasitic capacitance DC to 50MHz analog signal frequency -60dB typical off-isolation at 5.0MHz CMOS logic circuitry for low power Excellent noise immunity Cascadable serial data register with latches Flexible operating supply voltages The Supertex HV2201 is a low charge injection, 8-channel, high voltage analog switch integrated circuit (IC). The device can be used in applications requiring high voltage switching controlled by low voltage control signals, such as medical ultrasound imaging, piezoelectric transducer drivers, and printers. The HV2201 is an enhanced version of the HV20220. Input data is shifted into an 8-bit shift register that can then be retained in an 8-bit latch. To reduce any possible clock feedthrough noise, the latch enable bar should be left high until all bits are clocked in. Data is clocked in during the rising edge of the clock. Using HVCMOS technology, this device combines high voltage bilateral DMOS switches and low power CMOS logic to provide efficient control of high voltage analog signals. Applications Medical ultrasound imaging NDT metal flaw detection Piezoelectric transducer drivers Inkjet printer heads Optical MEMS modules The device is suitable for various combinations of high voltage supplies, e.g., VPP/VNN: +40V/-160V, +100V/-100V, and +160V/40V. Block Diagram Latches CLK DIN 8-Bit Shift Register Level Shifters Output Switches D LE CL SW0 D LE CL SW1 D LE CL SW2 D LE CL SW6 D LE CL SW7 DOUT VDD GND Supertex inc. LE CLR VNN VPP 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com HV2201 Ordering Information Package Options 48-Lead LQFP Device 28-Lead PLCC 7.00x7.00mm body 1.60mm height (max) 0.50mm pitch .453x.453in body .180in height (max) .050in pitch HV2201FG-G HV2201PJ-G HV2201 -G indicates the part is RoHS compliant (Green) Pin Configuration Absolute Maximum Ratings Parameter 1 Value VDD logic supply -0.5V to +7.0V VPP - VNN differential supply 220V VPP positive supply -0.5V to VNN+200V VNN negative supply 48-Lead LQFP (FG) +0.5V to -200V Logic input voltage (top view) -0.5V to VDD +0.3V Analog signal range 4 Storage temperature 26 3.0A -65C to 150C Power dissipation: 48-Lead LQFP 28-Lead PLCC 1.0W 1.2W Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. 28-Lead PLCC (PJ) (top view) Product Marking Top Marking YYWW Operating Conditions HV2 2 0 1 FG LLLLLLLLL Parameter Value Bottom Marking VDD Logic power supply voltage 3.0V to 5.5V VPP Positive high voltage supply 40V to VNN +200V VNN Negative high voltage supply VIH High level input voltage 0.9VDD to VDD VIL Low-level input voltage 0V to 0.1VDD Top Marking VSIG Analog signal voltage peak-to-peak VNN +10V to VPP -10V YYWW AAA TA 1 28 VNN to VPP Peak analog signal current/channel Sym 48 Operating free air temperature -40V to -160V 0OC to 70OC Notes: 1. Power up/down sequence is arbtrary except GND must be powered-up first and powered-down last. 2. VSIG must be VNN VSIG VPP or floating during power up/down transition. 3. Rise and fall times of power supplies VDD, VPP, and VNN should not be less than 1.0msec. CCCCCCCC AAA YY = Year Sealed WW = Week Sealed L = Lot Number C = Country of Origin* A = Assembler ID* = "Green" Packaging *May be part of top marking Package may or may not include the following marks: Si or 48-Lead LQFP (FG) HV2201PJ LLLLLLLLLL Bottom Marking CCCCCCCCCCC YY = Year Sealed WW = Week Sealed L = Lot Number A = Assembler ID C = Country of Origin* = "Green" Packaging *May be part of top marking Package may or may not include the following marks: Si or 28-Lead PLCC (PJ) Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 2 HV2201 DC Electrical Characteristics (Over operating conditions unless otherwise specified ) Sym RONS 0OC Parameter Small signal switch on-resistance +25OC +70OC Units Conditions Min Max Min Typ Max Min Max - 30 - 26 38 - 48 ISIG = 5.0mA - 25 - 22 27 - 32 ISIG = 200mA - 25 - 22 27 - 30 - 18 - 18 24 - 27 - 23 - 20 25 - 30 ISIG = 5.0mA - 22 - 16 25 - 27 ISIG = 200mA ISIG = 5.0mA ISIG = 200mA VPP = +40V VNN = -160V VPP = +100V VNN = -100V VPP = +160V VNN = -40V RONS Small signal switch on-resistance matching - 20 - 5.0 20 - 20 % ISIG = 5.0mA, VPP = +100V, VNN = - 100V RONL Large signal switch on-resistance - - - 15 - - - VSIG = VPP -10V, ISIG = 1.0A ISOL Switch off leakage per switch - 5.0 - 1.0 10 - 15 A VSIG = VPP -10V, VNN +10V DC offset switch off - 300 - 100 300 - 300 mV DC offset switch on - 500 - 100 500 - 500 mV IPPQ Quiescent VPP supply current - - - 10 50 - - A All switches off INNQ Quiescent VNN supply current - - - -10 -50 - - A All switches off IPPQ Quiescent VPP supply current - - - 10 50 - - A All switches on, ISW = 5.0mA INNQ Quiescent VNN supply current - - - -10 -50 - - A All switches on, ISW = 5.0mA ISW Switch output peak current - 3.0 - 3.0 2.0 - 2.0 A VSIG duty cycly < 0.1% fSW Output switching frequency - - - - 50 - - kHz - 4.0 - - 5.0 - 5.5 - 3.5 - - 3.5 - 3.5 - 3.5 - - 3.5 - 4.0 VPP = +160V VNN = -40V - 4.5 - - 5.0 - 5.5 VPP = +40V VNN = -160V - 3.5 - - 3.5 - 3.5 - 3.5 - - 3.5 - 4.0 VOS IPP INN Average VPP supply current Average VNN supply curent 100k load Duty cycle = 50% VPP = +40V VNN = -160V mA mA VPP = +100V VNN = -100V VPP = +100V VNN = -100V VPP = +160V VNN = -40V All output switches are turning on and off at 50kHz with no load All output switches are turning on and off at 50kHz with no load IDD Average VDD supply current - 4.0 - - 4.0 - 4.0 mA fCLK = 5MHz, VDD = 5.0V IDDQ Quiescent VDD supply current - 10 - - 10 - 10 A All logic inputs are static ISOR Data out source current 0.45 - 0.45 0.70 - 0.40 - mA VOUT = VDD -0.7V ISINK Data out sink current 0.45 - 0.45 0.70 - 0.40 - mA VOUT = 0.7V CIN Logic input capacitance - 10 - - 10 - 10 pF --- Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 3 HV2201 AC Electrical Characteristics (Over recommended operating conditions: VDD = 5.0V, tR = tF 5ns, 50% duty cycle, CLOAD = 20pF, unless otherwise specified) Sym 0OC Parameter tSD Set up time before LE rises tWLE Time width of LE tDO Clock delay time to data out tWCL Time width of CL tSU Set up time data to clock tH Hold time data from clock +25OC +70OC Units Conditions Min Max Min Typ Max Min Max 25 - 25 - - 25 - 56 - - 56 - 56 - 12 - - 12 - 12 - - 120 - 95 140 - 167 - 58 - 40 69 - 85 55 - 55 - - 55 - 39 - 47 30 - 58 - 16 - 21 10 - 26 - 2 - 2 - - 2 - - - - 8 - - - - - - 20 - - - - 50 - 50 ns --- ns ns ns ns ns ns VDD = 3.0V VDD = 5.0V VDD = 3.0V VDD = 5.0V --VDD = 3.0V VDD = 5.0V VDD = 3.0 or 5.0V VDD = 3.0V fCLK Clock frequency tR, tF Clock rise and fall times - 50 tON Turn on time - 5.0 - - 5.0 - 5.0 s VSIG = VPP -10V, RLOAD = 10k tOFF Turn off time - 5.0 - - 5.0 - 5.0 s VSIG = VPP -10V, RLOAD = 10k - 20 - - 20 - 20 - 20 - - 20 - 20 - 20 - - 20 - 20 -30 - -30 -33 - -30 - -58 - -58 - - -58 - -60 - -60 -70 - -60 - dB f = 5.0MHz, 50 load - 300 - - 300 - 300 mA 300ns pulse width, 2.0% duty cycle CSG(OFF) Off capacitance SW to GND 5.0 17 5.0 12 17 5.0 17 pF 0V, f = 1.0MHz CSG(ON) 25 50 25 38 50 25 50 pF 0V, f = 1.0MHz +VSPK - - - - 150 - - -VSPK - - - - 150 - - - - - - 150 - - - - - - 150 - - +VSPK - - - - 150 - - -VSPK - - - - 150 - - - - - 820 - - - - - - 600 - - - - - - 350 - - - dv/dt Maximun VSIG slew rate KO Off isolation KCR Switch crosstalk IID +VSPK -VSPK QC Output switch isolation diode current On capacitance SW to GND Output voltage spike Charge injection Supertex inc. MHz --- VDD = 5.0V VPP = +40V, VNN = -160V V/ns VPP = +100V, VNN = -100V VPP = +160V, VNN = -40V dB f = 5.0MHz, 1.0k/15pF load f = 5.0MHz, 50 load VPP = +40V, VNN = -160V, RLOAD = 50 mV VPP = +100V, VNN = -100V, RLOAD = 50 VPP = +160V, VNN = -40V, RLOAD = 50 VPP = +40V, VNN = -160V, VSIG = 0V pC VPP = +100V, VNN = -100V, VSIG = 0V VPP = +160V, VNN = -40V, VSIG = 0V 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 4 HV2201 Truth Table D0 D1 D2 D3 D4 D5 D6 D7 LE CLR SW0 SW1 SW2 SW3 SW4 SW5 L L L Off H L L On L L L Off H L L On L L L Off H L L On L L L Off H L L On L L L Off H L L On L L L Off H L L On L L L Off H L L On L L L Off H L L On X X X X X X X X H L Hold Previous State X X X X X X X X X H All Switches Off SW6 SW7 Notes: 1. The eight switches operate independently. 2. Serial data is clocked in on the L to H transition of the CLK. 3. The switches go to a state retaining their present condition at the rising edge of LE. When LE is low the shift register data flow through the latch. 4. DOUT is high when data in the shift register 7 is high. 5. Shift register clocking has no effect on the switch states if LE is high. 6. The CLR clear input overrides all other inputs. Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 5 HV2201 Test Circuits VPP -10V ISOL VPP -10V RL VOUT VOUT Open 100k VPP VPP VDD VNN VNN GND 10k RL VPP VPP VDD VNN VNN GND 5V 5V VPP VPP VDD VNN VNN GND TON/TOFF Test Circuit DC Offset ON/OFF Switch OFF Leakage VIN = 10VP-P @5.0MHz 5V VIN = 10VP-P @5.0MHz VSIG IID VOUT RL VPP VNN VDD VPP 5V VPP GND VNN KO = 20Log VOUT VIN 50 VPP 5V VDD VNN VNN GND VPP VPP VDD VNN VNN GND KCR = 20Log OFF Isolation VOUT VIN Crosstalk Isolation Diode Current +VSPK VOUT VOUT VOUT -VSPK 1000pF RL VSIG 50 1k VPP VPP VDD VNN VNN GND 5V VPP VPP VDD VNN VNN GND 5V Q = 1000pF x VOUT Charge Injection Supertex inc. 50 NC VNN Output Voltage Spike 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 6 5V HV2201 Typical Waveforms DN DN+1 DATA DN-1 50% IN 50% 50% 50% LE tWLE tSD 50% CLOCK tSU 50% th tDO DATA 50% OUT tON tOFF VOUT OFF 90% (TYP) ON CLR LR 10% 50% tWCL Supertex inc. 50% 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 7 HV2201 Pin Configuration 48-Lead LQFP - (FG) Pin Configuration 28-Lead PLCC (PJ) Pin # Pin Name Pin # Pin Name Pin # Pin Name Pin # Pin Name 1 SW5 25 VNN 1 SW3 15 NC 2 NC 26 NC 2 SW3 16 DIN 3 SW4 27 NC 3 SW2 17 CLK 4 NC 28 GND 4 SW2 18 LE 5 SW4 29 VDD 5 SW1 19 CLR 6 NC 30 NC 6 SW1 20 DOUT 7 NC 31 NC 7 SW0 21 SW7 8 SW3 32 NC 8 SW0 22 SW7 9 NC 33 DIN 9 NC 23 SW6 10 SW3 34 CLK 10 VPP 24 SW6 11 NC 35 LE 11 NC 25 SW5 12 SW2 36 CLR 12 VNN 26 SW5 13 NC 37 DOUT 13 GND 27 SW4 14 SW2 38 NC 14 VDD 28 SW4 15 NC 39 SW7 16 SW1 40 NC 17 NC 41 SW7 18 SW1 42 NC 19 NC 43 SW6 20 SW0 44 NC 21 NC 45 SW6 22 SW0 46 NC 23 NC 47 SW5 24 VPP 48 NC Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 8 HV2201 48-Lead LQFP Package Outline (FG) 7.00x7.00mm body, 1.60mm height (max), 0.50mm pitch D D1 E E1 Note 1 (Index Area D1/4 x E1/4) 48 1 e b Top View L2 View B A A2 L Seating Plane L1 Side View A1 Gauge Plane Seating Plane View B Note: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. Symbol MIN Dimension NOM (mm) MAX A A1 A2 b D D1 E E1 1.40* 0.05 1.35 0.17 8.80* 6.80* 8.80* 6.80* - - 1.40 0.22 9.00 7.00 9.00 7.00 1.60 0.15 1.45 0.27 9.20* 7.20* 9.20* 7.20* e 0.50 BSC L 0.45 0.60 0.75 L1 1.00 REF JEDEC Registration MS-026, Variation BBC, Issue D, Jan. 2001. * This dimension is not specified in the JEDEC drawing. Drawings are not to scale. Supertex Doc. #: DSPD-48LQFPFG Version, D041309. Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 9 L2 0.25 BSC 0O 3.5O 7O HV2201 28-Lead PLCC Package Outline (PJ) .453x.453in. body, .180in. height (max), .050in. pitch .048/.042 x 45O D D1 1 4 26 28 .150 MAX .056/.042 x 45O Note 1 (Index Area) .075 MAX E1 E Note 2 .020max (3 Places) Top View Vertical Side View View A b1 A Base .020 MIN Plane A1 A2 Seating Plane e b Horizontal Side View R View A Notes: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. 2. Actual shape of this feature may vary. Symbol Dimension (inches) A A1 A2 b b1 D D1 E E1 MIN .165 .090 .062 .013 .026 .485 .450 .485 .450 NOM .172 .105 - - - .490 .453 .490 .453 MAX .180 .120 .083 .021 .032 .495 .456 .495 .456 e .050 BSC R .025 .035 .045 JEDEC Registration MS-018, Variation AB, Issue A, June, 1993. Drawings not to scale. Supertex Doc. #: DSPD-28PLCCPJ, Version B031111. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate "product liability indemnification insurance agreement." Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com) Supertex inc. (c)2011 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSFP-HV2201 B040811 10 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com