Rev.1.00, Aug.20.2004, page 1 of 14
BCR12PM-12L
Triac
Medium Power Use
REJ03G0305-0100
Rev.1.00
Aug.20.2004
Features
• IT (RMS) : 12 A
• VDRM : 600 V
• IFGTI, IRGTI, IRGTⅢ : 30 mA (20 mA)Note5
• Viso : 2000 V
• Insulated Type
• Planar Passivation Type
• UL Recognized : Yello w Card No. E223904
File No. E80271
Outline
2
1
3
TO-220F
2
1
3
1. T
1
Terminal
2. T
2
Terminal
3. Gate Terminal
Applications
Switching mode power supply, light dimmer, electronic flasher unit, hair drier, control of household equipment such as
TV sets, stereo systems, refrigerator, washing machine, infrared kotatsu, carpet, solenoid driver, small motor control,
solid state relay, copying machine, electric tool, electric heater control, and other general controlling devices
Maximum Ratings
Voltage class
Parameter Symbol 12 Unit
Repetitive peak off-state voltageNote1 VDRM 600 V
Non-repetitive peak off-state voltageNote1 VDSM 720 V
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 2 of 14
Parameter Symbol Ratings Unit Conditions
RMS on-state current IT (RMS) 12 A Commercial frequency, sine full wave
360° conduction, Tc = 74°C
Surge on-state current ITSM 120 A 60Hz sinewave 1 full cycle, peak valu e,
non-repetitive
I2t for fusing I2t60A
2s Value corresponding to 1 cycle of half
wave 60Hz, surge on-state current
Peak gate power dissipation PGM 5W
Average gate power dissipation PG (AV) 0.5 W
Peak gate voltage VGM 10 V
Peak gate current IGM 2A
Junction temperature Tj – 40 to +125 °C
Storage temperature Tstg – 40 to +125 °C
Mass — 2.0 g Typical value
Isolation voltage Viso 2000 V Ta = 25°C, AC 1 minute,
T1·T2·G terminal to case
Notes: 1. Gate open.
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Test conditions
Repetitive peak off-state current IDRM — — 2.0 mA Tj = 125°C, VDRM applied
On-state voltage VTM — — 1.6 V Tc = 25°C, ITM = 20 A,
Instantaneous measurement
ΙVFGTΙ——1.5V
ΙΙ VRGTΙ——1.5V
Gate trigger voltageNote2
ΙΙΙ VRGTΙΙΙ ——1.5V
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
ΙIFGTΙ——30
Note5 mA
ΙΙ IRGTΙ——30
Note5 mA
Gate trigger currentNote2
ΙΙΙ IRGTΙΙΙ ——30
Note5 mA
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
Gate non-trigger voltage VGD 0.2 — — V Tj = 125°C, VD = 1/2 VDRM
Thermal resistance Rth (j-c) ——3.5°C/W Junction to caseNote3
Critical-rate of rise of off-state
commutating voltageNote4 (dv/dt)c 10 — — V/µs Tj = 125°C
Notes: 2. Measurement using the gate trigger characteristics measurement circuit.
3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W.
4. Test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below.
5. High sensitivit y (IGT ≤ 20 mA) is also available. (IGT item: 1)
Test conditions Commutating voltage and curr ent waveforms
(inductive load)
1. Junction temperature
Tj = 125°C
2. Rate of decay of on-state commutating current
(di/dt)c = – 6.0 A/ms
3. Peak off-state voltage
VD = 400 V
Supply Voltage
Time
Time
Time
Main Current
Main Voltage
(di/dt)c
V
D
(dv/dt)c
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 3 of 14
Performance Curves
Maximum On-State Characteristics
On-State Voltage (V)
On-State Current (A)
Rated Surge On-State Current
Conduction Time (Cycles at 60Hz)
Surge On-State Current (A)
Gate Characteristics (I, II and III)
Gate Current (mA)
Gate Voltage (V)
Gate Trigger Voltage vs.
Junction Temperature
Junction Temperature (°C)
Gate Trigger Voltage (Tj = t°C)
Gate Trigger Voltage (Tj = 25°C)
×
100 (%)
Gate Trigger Current vs.
Junction Temperature
Junction Temperature (°C)
Gate Trigger Current (Tj = t°C)
Gate Trigger Current (Tj = 25°C)
× 100 (%)
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
Conduction Time (Cycles at 60Hz)
Transient Thermal Impedance (°C/W)
10
0
2510
1
80
40
37 10
2
425
37
4
120
160
200
60
20
100
140
180
0
3.80.6 1.4 2.2 3.01.0 1.8 2.6 3.4
10
2
7
5
3
2
10
1
7
5
3
2
10
0
7
5
3
2
10
–1
2310
–1
5710
0
23 5710
1
23 5710
2
3.5
3.0
2.5
2.0
1.5
1.0
0.5
4.0
0
2310
2
5710
3
23 5
10
0
2310
1
5710
2
23 5710
3
23 5710
4
10
2
7
5
3
2
10
1
7
5
3
2
7
5
3
2
10
–1
10
1
10
3
7
5
3
2
–60 –20 20
10
2
7
5
3
2
60 100 140
4
4
–40 0 40 80 120
10
1
10
3
7
5
3
2
–60 –20 20
10
2
7
5
3
2
60 100 140
4
4
–40 0 40 80 120
Tj = 25°C
Tj = 125°C
V
GD
= 0.2V
I
FGT I
, I
RGT III
I
RGT I
V
GT
= 1.5V
V
GM
= 10V
P
GM
= 5W
I
GM
= 2A
P
G(AV)
=
0.5W
Typical Example
I
RGT I
, I
RGT III
I
FGT I
Typical Example
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 4 of 14
Maximum Transient Thermal Impedance
Characteristics (Junction to ambient)
Transient Thermal Impedance (°C/W)
Conduction Time (Cycles at 60Hz)
On-State Power Dissipation (W)
RMS On-State Current (A)
Maximum On-State Power Dissipation
RMS On-State Current (A)
Case Temperature (°C)
Allowable Case Temperature vs.
RMS On-State Current
RMS On-State Current (A)
Allowable Ambient Temperature vs.
RMS On-State Current
Ambient Temperature (°C)
RMS On-State Current (A)
Ambient Temperature (°C)
Allowable Ambient Temperature vs.
RMS On-State Current
Junction Temperature (°C)
Repetitive Peak Off-State Current (Tj = t°C)
Repetitive Peak Off-State Current (Tj = 25°C) × 100 (%)
Repetitive Peak Off-State Current vs.
Junction Temperature
10
3
10
–1
10
3
10
4
10
2
7
5
3
2
10
0
7
5
3
2
10
1
7
5
3
2
7
5
3
2
10
1
23 57 23 57
10
2
10
5
23 57 23 57
16
12
6
4
2
14
10
8
016
024 86 10121
4
14040–40–60 –20 0 20 60 80 100120
10
5
7
5
3
2
10
4
7
5
3
2
10
3
7
5
3
2
10
2
160
120
100
60
20
016
02 6 10 14
40
80
140
4812
160
120
100
60
20
04.0
00.5 1.5 2.5 3.5
40
80
140
1.0 2.0 3.0
160
120
100
60
20
016
02 6 10 14
40
80
140
4812
No Fins
360° Conduction
Resistive,
inductive loads
Curves apply regardless
of conduction angle
All fins are black painted
aluminum and greased
Curves apply
regardless of
conduction angle
Resistive,
inductive loads
Natural convection
120 × 120 × t2.3
100 × 100 × t2.3
60 × 60 × t2.3
Typical Example
Natural convection
No Fins
Curves apply regardless
of conduction angle
Resistive, inductive loads
360° Conduction
Resistive,
inductive loads
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 5 of 14
Holding Current vs.
Junction Temperature
Junction Temperature (°C)
Holding Current (Tj = t°C)
Holding Current (Tj = 25°C) × 100 (%)
Latching Current (mA)
Latching Current vs.
Junction Temperature
Junction Temperature (°C)
Rate of Rise of Off-State Voltage (V/µs)
Breakover Voltage (dv/dt = xV/µs)
Breakover Voltage (dv/dt = 1V/µs) × 100 (%)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage
Breakover Voltage vs.
Junction Temperature
Junction Temperature (°C)
Breakover Voltage (Tj = t°C)
Breakover Voltage (Tj = 25°C) × 100 (%)
Commutation Characteristics
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Rate of Decay of On-State
Commutating Current (A/ms)
Gate Trigger Current (tw)
Gate Trigger Current (DC) × 100 (%)
Gate Current Pulse Width (µs)
Gate Trigger Current vs.
Gate Current Pulse Width
10
3
7
5
3
2
–60 –20 20
10
2
7
5
3
2
60 100 140
4
4
–40 0 40 80 120
10
1
160–40 0 40 80 120
10
3
7
5
3
2
10
2
7
5
3
2
10
1
7
5
3
2
10
0
160
100
80
40
20
014040–40–60 –20 0 20 60 80
140
100 120
60
120
10
1
10
3
7
5
3
2
10
0
23 5710
1
10
2
7
5
3
2
23 5710
2
4
4
4
4
2310
1
5710
2
23 5710
3
23 5710
4
120
0
20
40
60
80
100
140
160
10
1
2310
0
5710
1
23 5710
2
7
5
3
2
7
5
7
3
2
10
0
Typical Example
T2+, G+
T2–, G–Typical Example
T2+, G–
Typical Example
Distribution
Typical Example
Tj = 125°C
Typical Example
III Quadrant
I Quadrant
Typical Example
Main Voltage
Main CurrentI
T
(di/dt)c
τ
V
D
Time
Time
(dv/dt)c
Typical Example
Tj = 125°C
IT = 4A
τ = 500µs
VD = 200V
f = 3Hz
Minimum
Characteristics
Value
III Quadrant
I Quadrant
I
FGT I
I
RGT I
I
RGT III
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 6 of 14
Test Procedure I
Test Procedure III
Test Procedure II
Gate Trigger Characteristics Test Circuits
6Ω6Ω
6Ω
6V 6V
6V
330Ω330Ω
330Ω
A
V
A
V
A
V
BCR12PM-12L
Rev.1.00, Aug.20.2004, page 7 of 14
Package Dimensions
TO-220F
EIAJ Package Code JEDEC Code Mass (g) (reference value) Lead Material
2.0 Cu alloyConforms
Symbol Dimension in Millimeters
Min Typ Max
A
A
1
A
2
b
D
E
e
x
y
1
y
ZD
ZE
10.5 max
1.3 max
5.2
2.54 2.54
2.8
0.5 2.6
0.8
φ 3.2 ± 0.2
8.5
1.2
5.0
17
3.6
4.5
13.5 min
Note 1) The dimensional figures indicate representative values unless
otherwise the tolerance is specified.
Order Code
Lead form Standard p acking Quantity Standard order code Standard order
code example
Straight type Vinyl sack 100 Type name +A BCR12PM-12LA
Lead form Plastic Magazine (Tube) 50 Type name +A – Lead forming code BCR12PM-12LA-A8
Note : Please confirm the specification about the shipping in detai l.
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 8 of 14
BCR12PM-12L
Triac
Medium Power Use
(The product guaranteed maximum junction temperature of 150°C)
Features
• IT (RMS) : 12 A
• VDRM : 600 V
• IFGTI, IRGTI, IRGTⅢ : 30 mA (20 mA)Note5
• Viso : 2000 V
• Insulated Type
• Planar Passivation Type
Outline
2
1
3
TO-220F
2
1
3
1. T
1
Terminal
2. T
2
Terminal
3. Gate Terminal
Applications
Switching mode power supply, light dimmer, electronic flasher unit, hair drier, control of household equipment such as
TV sets, stereo systems, refrigerator, washing machine, infrared kotatsu, carpet, solenoid driver, small motor control,
solid state relay, copying machine, electric tool, electric heater control, and other general controlling devices
Warning
1. Refer to the recommended circuit values around the tria c before using.
2. Be sure to exchange the specification before using. Otherwise, general triacs with the maximum
junction temperature of 125°C will be supplied.
Maximum Ratings
Voltage class
Parameter Symbol 12 Unit
Repetitive peak off-state voltageNote1 VDRM 600 V
Non-repetitive peak off-state voltageNote1 VDSM 720 V
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 9 of 14
Parameter Symbol Ratings Unit Conditions
RMS on-state current IT (RMS) 12 A Commercial frequency, sine full wave
360° conduction, Tc = 99°C
Surge on-state current ITSM 120 A 60Hz sinewave 1 full cycle, peak value,
non-repetitive
I2t for fusing I2t60A
2sValue corresponding to 1 cycle of ha lf
wave 60Hz, surge on-state current
Peak gate power dissipation PGM 5W
Average gate power dissipation PG (AV) 0.5 W
Peak gate voltage VGM 10 V
Peak gate current IGM 2A
Junction temperature Tj – 40 to +150 °C
Storage temperature Tstg – 40 to +150 °C
Mass — 2.0 g Typical value
Isolation voltage Viso 2000 V Ta = 25°C, AC 1 minute,
T1·T2·G terminal to case
Notes: 1. Gate open.
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Test conditions
Repetitive peak off-state current IDRM — — 2.0 mA Tj = 150°C, VDRM applied
On-state voltage VTM ——1.6V
Tc = 25°C, ITM = 20 A,
Instantaneous measurement
ΙVFGTΙ——1.5V
ΙΙ VRGTΙ——1.5V
Gate trigger voltageNote2
ΙΙΙ VRGTΙΙΙ ——1.5V
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
ΙIFGTΙ——30
Note5 mA
ΙΙ IRGTΙ——30
Note5 mA
Gate trigger currentNote2
ΙΙΙ IRGTΙΙΙ ——30
Note5 mA
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
Gate non-trigger voltage VGD 0.2/0.1 — — V Tj = 125°C/150°C, VD = 1/2 VDRM
Thermal resistance Rth (j-c) ——3.5°C/W Junction to caseNote3
Critical-rate of rise of off-state
commutating voltageNote4 (dv/dt)c 10/1 — — V/µs Tj = 125°C/150°C
Notes: 2. Measurement using the gate trigger characteristics measurement circuit.
3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W.
4. Test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below.
5. High sensitivit y (IGT ≤ 20 mA) is also available. (IGT item: 1)
Test conditions Commutating voltage and curr ent waveforms
(inductive load)
1. Junction temperature
Tj = 125°C/150°C
2. Rate of decay of on-state commutating current
(di/dt)c = – 6.0 A/ms
3. Peak off-state voltage
VD = 400 V
Supply Voltage
Time
Time
Time
Main Current
Main Voltage
(di/dt)c
V
D
(dv/dt)c
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 10 of 14
Performance Curves
Maximum On-State Characteristics
On-State Voltage (V)
On-State Current (A)
Rated Surge On-State Current
Conduction Time (Cycles at 60Hz)
Surge On-State Current (A)
Gate Characteristics (I, II and III)
Gate Current (mA)
Gate Voltage (V)
Gate Trigger Voltage vs.
Junction Temperature
Junction Temperature (°C)
Gate Trigger Voltage (Tj = t°C)
Gate Trigger Voltage (Tj = 25°C)
×
100 (%)
Gate Trigger Current vs.
Junction Temperature
Junction Temperature (°C)
Gate Trigger Current (Tj = t°C)
Gate Trigger Current (Tj = 25°C)
× 100 (%)
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
Conduction Time (Cycles at 60Hz)
Transient Thermal Impedance (°C/W)
10
0
2510
1
80
40
37
10
2
4
25
37
4
120
160
200
60
20
100
140
180
0
0.5 1.5 2.5 3.51.0 2 3.0 4.0
10
2
7
5
3
2
10
1
7
5
3
2
10
0
7
5
2310
–1
5710
0
23 5710
1
23 5710
2
3.5
3.0
2.5
2.0
1.5
1.0
0.5
4.0
0
2310
2
5710
3
23 5
10
0
2310
1
5710
2
23 5710
3
23 5710
4
5
3
2
10
1
7
5
3
2
7
5
3
2
10
–1
10
1
10
3
7
5
3
2
10
2
7
5
3
2
4
4
10
1
10
3
7
5
3
2
–60 –20 20
10
2
7
5
3
2
60 100 140
4
4
–40 0 40 80 120 160
–60 –20 20 60 100 140–40 0 40 80 120 160
Tj = 25°C
Tj = 150°C
V
GM
= 10V
I
GM
= 2A
P
GM
= 5W
V
GT
= 1.5V
I
FGT I
, I
RGT III
I
RGT I
V
GD
= 0.1V
P
G(AV)
=
0.5W
I
RGT I
, I
RGT III
I
FGT I
Typical Example
Typical Example
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 11 of 14
Maximum Transient Thermal Impedance
Characteristics (Junction to ambient)
Transient Thermal Impedance (°C/W)
Conduction Time (Cycles at 60Hz)
On-State Power Dissipation (W)
RMS On-State Current (A)
Maximum On-State Power Dissipation
RMS On-State Current (A)
Case Temperature (°C)
Allowable Case Temperature vs.
RMS On-State Current
RMS On-State Current (A)
Allowable Ambient Temperature vs.
RMS On-State Current
Ambient Temperature (°C)
RMS On-State Current (A)
Ambient Temperature (°C)
Allowable Ambient Temperature vs.
RMS On-State Current
Junction Temperature (°C)
Repetitive Peak Off-State Current (Tj = t°C)
Repetitive Peak Off-State Current (Tj = 25°C) × 100 (%)
Repetitive Peak Off-State Current vs.
Junction Temperature
10
3
10
–1
10
3
10
4
10
2
7
5
3
2
10
0
7
5
3
2
10
1
7
5
3
2
7
5
3
2
10
1
23 57 23 57
10
2
10
5
23 57 23 57
16
12
6
4
2
14
10
8
016
024 86 101214
10
5
7
5
3
2
10
4
7
5
3
2
10
3
7
5
3
2
10
2
160
120
100
60
20
016
02 6 10 14
40
80
140
48
12
160
120
100
60
20
04.0
00.5 1.5 2.5 3.5
40
80
140
1.0 2.0 3.0
160
120
100
60
20
016
02 6 10 14
40
80
140
48
12
–60 –20 20 60 100 140–40 0 40 80 120 160
No Fins
Curves apply regardless
of conduction angle
360° Conduction
Resistive,
inductive loads
All fins are black painted
aluminum and greased
120 × 120 × t2.3
100 × 100 × t2.3
60 × 60 × t2.3
Curves apply
regardless of
conduction angle
Resistive,
inductive loads
Natural convection
360° Conduction
Resistive,
inductive loads
Natural convection
No Fins
Curves apply regardless
of conduction angle
Resistive, inductive loads
Typical Example
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 12 of 14
Rate of Rise of Off-State Voltage (V/µs)
Breakover Voltage (dv/dt = xV/µs)
Breakover Voltage (dv/dt = 1V/µs) × 100 (%)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj=125°C)
Rate of Rise of Off-State Voltage (V/µs)
Breakover Voltage (dv/dt = xV/µs)
Breakover Voltage (dv/dt = 1V/µs) × 100 (%)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj=150°C)
Breakover Voltage vs.
Junction Temperature
Junction Temperature (°C)
Breakover Voltage (Tj = t°C)
Breakover Voltage (Tj = 25°C) × 100 (%)
Commutation Characteristics (Tj=125°C)
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Rate of Decay of On-State
Commutating Current (A/ms)
Holding Current vs.
Junction Temperature
Junction Temperature (°C)
Holding Current (Tj = t°C)
Holding Current (Tj = 25°C) × 100 (%)
Latching Current (mA)
Latching Current vs.
Junction Temperature
Junction Temperature (°C)
10
3
7
5
3
2
10
2
7
5
3
2
4
4
10
1
160–40 0 40 80 120
10
3
7
5
3
2
10
2
7
5
3
2
10
1
7
5
3
2
10
0
–60 –20 20 60 100 140–40 0 40 80 120 160
160
100
80
40
20
0
140
60
120
2310
1
5710
2
23 5710
3
23 5710
4
120
0
20
40
60
80
100
140
160
10
2
2310
0
5710
1
23 5710
2
7
5
10
1
7
3
2
7
5
10
0
3
2
–60 –20 20 60 100 140–40 0 40 80 120 160
2310
1
5710
2
23 5710
3
23 5710
4
120
0
20
40
60
80
100
140
160
Typical Example
Typical Example
Distribution
T2+, G–
Typical Example
T2+, G+
T2–, G–Typical Example
Typical Example
Tj = 125°C
III Quadrant
I Quadrant
Main Voltage
Main CurrentI
T
(di/dt)c
τ
V
D
Time
Time
(dv/dt)c
I Quadrant
III Quadrant
Minimum
Characteristics
Value
Typical Example
Tj = 125°C
IT = 4A
τ = 500µs
VD = 200V
f = 3Hz
Typical Example
Tj = 150°C
III Quadrant
I Quadrant
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 13 of 14
C
1
= 0.1 to 0.47µF
R
1
= 47 to 100Ω
C
0
= 0.1µF
R
0
= 100Ω
Gate Trigger Characteristics Test Circuits Recommended Circuit Values Around The Triac
Test Procedure I
Test Procedure III
Test Procedure II
Commutation Characteristics (Tj=150°C)
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Rate of Decay of On-State
Commutating Current (A/ms)
Gate Trigger Current (tw)
Gate Trigger Current (DC) × 100 (%)
Gate Current Pulse Width (µs)
Gate Trigger Current vs.
Gate Current Pulse Width
10
1
10
3
7
5
3
2
10
0
23 5710
1
10
2
7
5
3
2
23 5710
2
4
4
44
10
2
2310
0
5710
1
23 5710
2
7
5
10
1
7
3
2
7
5
10
0
3
2
C
1
C
0
R
0
R
1
6Ω6Ω
6Ω
6V 6V
6V
330Ω330Ω
330Ω
A
V
A
V
A
V
Typical Example
Tj = 150°C
I
T
= 4A
τ = 500µs
V
D
= 200V
f = 3Hz
Main Voltage
Main CurrentI
T
(di/dt)c
τ
V
D
Time
Time
(dv/dt)c
I Quadrant
III Quadrant
Minimum
Characteristics
Value
Typical Example
IRGT III
IRGT I
IFGT I
Load
BCR12PM-12L (The product guaranteed maximum junction temperature o f 150°C)
Rev.1.00, Aug.20.2004, page 14 of 14
Package Dimensions
TO-220F
EIAJ Package Code JEDEC Code Mass (g) (reference value) Lead Material
2.0 Cu alloyConforms
Symbol Dimension in Millimeters
Min Typ Max
A
A
1
A
2
b
D
E
e
x
y
1
y
ZD
ZE
10.5 max
1.3 max
5.2
2.54 2.54
2.8
0.5 2.6
0.8
φ 3.2 ± 0.2
8.5
1.2
5.0
17
3.6
4.5
13.5 min
Note 1) The dimensional figures indicate representative values unless
otherwise the tolerance is specified.
Order Code
Lead form Standard packing Quantity Standard order code Standard order
code example
Straight type Vinyl sack 100 Type name +B BCR12PM-12LB
Lead form Plastic Magazine (Tube) 50 Type name +B – Lead forming code BCR12PM-12LB-A8
Note : Please confirm the specification about the shipping in detai l.
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
http://www.renesas.com
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501
Renesas Technology Europe Limited.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom
Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900
Renesas Technology Europe GmbH
Dornacher Str. 3, D-85622 Feldkirchen, Germany
Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11
Renesas Technology Hong Kong Ltd.
7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2375-6836
Renesas Technology Taiwan Co., Ltd.
FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
RENESAS SALES OFFICES
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .1.0
