Panel and Legend Mounts for LED Light Bars Technical Data HLMP-2598 HLMP-2599 HLMP-2898 HLMP-2899 Features Description * Firmly Mounts Light Bars in Panels * Holds Legends for Front Panel or PC Board Applications[1] * One Piece, Snap-in Assembly * Matte Black Bezel Design Enhances Panel Appearance * Four Sizes Available * May Be Installed in a Wide Range of Panel Thicknesses * Panel Hole Easily Punched or Milled This series of black plastic bezel mounts is designed to install Agilent Light Bars in instrument panels ranging in thickness from 1.52 mm (0.060 inch) to 3.18 mm (0.125 inch). A space has been provided for holding a 0.13 mm (0.005 inch) film legend over the light emitting surface of the light bar module. Selection Guide Panel and Legend Mount Part No. HLMP2598 2599 2898 2899 Corresponding Light Bar Module Part No. HLCPHLMPB100 2350, 2450, 2550 A100 2300, 2400, 2500 D100 2600, 2700, 2800 C100 2655, 2755, 2855 2950, 2965, 2980 E100 2620, 2720, 2820 F100 2635, 2735, 2835 G100 2670, 2770, 2870 H100 2685, 2785, 2885 Panel Hole Installation Dimensions[2] 7.62 mm (0.300 inch) x 22.86 mm (0.900 inch) 7.62 mm (0.300 inch) x 12.70 mm (0.500 inch) 12.70 mm (0.500 inch) x 12.70 mm (0.500 inch) Package Outline B A C 12.70 mm (0.500 inch) x 22.86 mm (0.900 inch) D Notes: 1. Application Note 1012 addresses legend fabrication options. 2. Allowed hole tolerance: +0.00 mm, -0.13 mm (+0.000 inch, -0.005 inch). Permitted radius: 1.60 mm (0.063 inch). 2 Package Dimensions Mounting Instructions 1. Mill[3] or punch a hole in the panel. Deburr, but do not chamfer, the edges of the hole. 2. Place the front of the mount against a solid, flat surface. A film legend with outside dimensions equal to the outside dimensions of the light bar may be placed in the mount or on the light bar light emitting surface. Press the light bar into the mount until the tabs snap over the back of the light bar[4]. When inserting the HLMP-2898, align the notched sides of the light bar with the mount sides which do not have the tabs. (See Figure 1.) 3. Applying even pressure to the top of the mount, press the entire assembly into the hole from the front of the panel[5]. (See Figure 2.) Note: For thinner panels, the mount may be pressed into the panel first, then the light bar may be pressed into the mount from the back side of the panel. Suggested Punch Sources Hole punches may be ordered from one of the following sources: Danly Machine Corporation Punchrite Division 15400 Brookpark Road Cleveland, OH 44135 (216) 267-1444 Notes: 3. A 3.18 mm (0.125 inch) diameter mill may be used. 4. Repetitve insertion of the light bar into mount may cause damage to the mount. 5. Repetitive insertion of the mount into the panel will degrade the retention force of the mount. Ring Division The Producto Machine Company Jamestown, NY 14701 (800) 828-2216 Porter Precision Products Company 12522 Lakeland Road Santa Fe Springs, CA 90670 (213) 946-1531 Di-Acro Division Houdaille Industries 800 Jefferson Street Lake City, MN 55041 (612) 345-4571 3 Installation Sketches Figure 1. Installation of a Light Bar into a Panel Mount. Figure 2. Installation of the Light Bar/Panel Mount Assembly into a Front Panel. www.semiconductor.agilent.com Data subject to change. Copyright (c) 1999 Agilent Technologies, Inc. November 30, 1999 Obsoletes 5953-0481E 5963-7038E