SPEC NO: DSAG0234 REV NO: V.12A DATE: JAN/04/2016 PAGE: 1 OF 5
APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000334
SURFACE MOUNT DISPLAY
Part Number: ACDC03-41SRWA-F01
Super Bright Red
Features
z0.3 inch digit height.
zLow current operation.
zExcellent character appearance.
zMechanically rugged.
zPackage :300pcs / reel.
zGray face, white segment.
zMoisture sensitivity level : level 2a.
zRoHS compliant.
Description
The Super Bright Red source color devices are made with
Gallium Aluminum Arsenide Red Light Emitting Diode.
Package Dimensions& Intern al Circuit Diagram
Notes:
1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted.
2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
3.The gap between the reflector and PCB shall not exceed 0.25mm.
SPEC NO: DSAG0234 REV NO: V.12A DATE: JAN/04/2016 PAGE: 2 OF 5
APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000334
Selection Guide
Note:
1. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25° C
Electrical / Optical Characteristics at TA=25°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Emitting Color (Material) Lens Type
Iv (ucd) [1]
@ 10mA Description
Min. Typ.
ACDC03-41SRWA-F01 Super Bright Red (GaAlAs) White Diffused
5600 9800
*1400 *2600
Common Cathode, Rt.
Hand Decimal.
Symbol Parameter Emitting Color Typ. Max. Units Test Conditions
λpeak Peak Wavelength Super Bright Red 655 nm IF=10mA
λD [1] Dominant Wavelength Super Bright Red 640 nm IF=10mA
Δλ1/2 Spectral Line Half-width Super Bright Red 20 nm IF=10mA
C Capacitance Super Bright Red 45 pF VF=0V;f=1MHz
VF [2] Forward Voltage Super Bright Red 1.8 2.5 V IF=10mA
IR Reverse Current Super Bright Red 10 uA VR=5V
Parameter Values Units
Power dissipation 75 mW
DC Forward Current 30 mA
Peak Forward Current [1] 155 mA
Reverse Voltage 5 V
Operating / Storage Temperature -40°C To +85°C
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
SPEC NO: DSAG0234 REV NO: V.12A DATE: JAN/04/2016 PAGE: 3 OF 5
APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000334
Super Bright Red ACDC03-41SRWA-F01
SPEC NO: DSAG0234 REV NO: V.12A DATE: JAN/04/2016 PAGE: 4 OF 5
APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000334
ACDC03-41SRWA-F01
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.15) Reel Dimension
Tape Specifications
(Units : mm)
SPEC NO: DSAG0234 REV NO: V.12A DATE: JAN/04/2016 PAGE: 5 OF 5
APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000334
PACKING & LABEL SPECIFICATIONS ACDC03-41SRWA-F01
Terms and conditions for the usage of this doc ument
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
