REV. 6/3/05 DATE REV ECN APP'D. BY 4-21-03 | Al 6007 RGC BOTTOM SURFACE OF JACK (PCB SURFACE) N=18-05 | A2 7588 TRM ( .708 [17.98] ) ( .148 [3.76] ) }-_ .635 [16.13] MAX.-} TO HIGHEST POINT OF BEAM | i \ i \ Ze | \ po [8 [16.66] ~| \__ (4) Roto [0.25] [ 7 A L _) = MAX. _ < N a = s | =, 3 5 For) Do wo eS = a a +H a STEWART % eS = * PATENTED ~ m x 3 i oO J | wt a _ Z | - om 7 L Yj 1 he | 000 [0.00] Y i | | Top OF PCB CG ( .083 [2.12] ) a __1 SUGGESTED PANEL OPENING TO BOTTOM | 275 [6.99] MAX. TO HIGHEST T OF OPENING _ nas__e| POINT OF BEAM 040 [1.02] (2)--] | K- J+ 545 [13.84] NOTES: 1. CONNECTOR MATERIALS: HOUSING: THERMOPLASTIC UL94 V-0 > CONTACTS/SHIELD: COPPER ALLOY = SHIELD PLATING: NICKEL OR TIN 2 CONTACT PLATING: SELECTIVE GOLD IN CONTACT AREA . = 00 [2.54](3) SEE CHART FOR PART NUMBER 2 ie 050 [1.27] (7) ee 2. FOR PRODUCT SPECIFICATIONS SEE PRO2201. = = : 4 w& > A | 050 [1.27] e 2 3, TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS. 2 i = 4, THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE = ft Qe & ( NW 9.035 [0.89] +.003 [0.08] (8) | 8 USER THE ABILITY TO HAVE REASONABLE JACK /PANEL 3 = 006 [0.15] PIN #1 & > CLEARANCES, YET MAINTAIN GROUNDING CAPABILITY. ; 3 6 & THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION = 6.065 [1.65] +.003 [0.08] (2) BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF Ze i) ot LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. * j* gt + & 006 [0.15] 2, 4, 6, 8 a te On By. tf 50 MICRO-INCHES [1.27um]| | SS6488SAPG4BA-50 | 125 [3:8] (2) 8 Jno TI ALT Ms 128 [3.25] oc 30 MICRO-INCHES [0.76um | SS6488SAPG4-BA _ 006 [0.15] .080 [2.03] I x R 450 [11.43 CONTACT PLATING j =, 610 [15.49] PART NUMBER f ee IN MATING AREA 1 r 8 P.C.B. RECOMMENDED HOLE LAYOUT \ 1 nm SEEN FROM COMPONENT SIDE THIRD ANGLE PROJECTION [t ALL CENTERLINE DIMENSIONS ARE. BASIC. Bel Stewart ( Onnector { 11118 Susquehanna Trail South i] 0 Glen Rock, PA 17327-9199 (717) 235-7512 Fax: (717) 235-7954 http: //www.stewartconnector.com TITLE: UN Eee EIGHT CONTACT, EIGHT POSITION, SHIELDED JACK i] 0 CHANGE WITHOUT NOTICE ENHANCED SHIELD DIMENSIONS: INCHES [METRIC] | THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON [RN SY: car | PATE) 4 _ nz UNLESS OTHERWSE SPECIFIED ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF L J TOLERANCES ARE +.005 [0.13] | BEL STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, | APPD BY: RCC DATE 3-10-03 \=/ \=/ ANGLES ARE + 1 COPIED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN SHEET NO. CONSENT OF BEL STEWART CONNECTOR. THE SUBJECT | DWG NO. REV. 1 OF 1 MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. C1T640146 A2 2 | AutoCAD