412-59586-G - POWER-ONE - Product.Network

Multiple Output Model Selection

–

130W Continuous Output Power

MODEL OUTPUT ADJUSTMENT OUTPUT PEAK CURRENT LINE LOAD TYPICAL RIPPLE & INITIAL SETTING

VOLTAGE RANGE CURRENT (NOTE 1) REGULATION REGULATION NOISE %p-p (NOTE 2) ACCURACY

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.1V to 5.2V

MAP130-4000 +12V 11.5V to 12.5V 5A 10A 0.5% 2% 1% 11.75V to 12.0V

-5V Fixed 1A 1A 0.5% 2% 1% -4.8V to -5.2V

-12V Fixed 1A 1A 0.5% 2% 1% -11.6V to -12.4V

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.1V to 5.2V

MAP130-4001 +24V 23.0V to 25.0V 3.5A 5A 0.5% 2% 1% 23.9V to 24.1V

-12V Fixed 1A 1A 0.5% 2% 1% -11.6V to -12.4V

+12V Fixed 1A 1A 0.5% 2% 1% -11.6V to -12.4V

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.1V to 5.2V

MAP130-4002 +12V 11.5V to 12.5V 5A 10A 0.5% 2% 1% 11.9V to 12.1V

-12V Fixed 1A 1A 0.5% 2% 1% -11.6V to -12.4V

+12V Fixed 1A 1A 0.5% 2% 1% 11.6V to 12.4V

MAP130 AC-DC Series Data Sheet

MCD10115 Rev. 1.3, 05-Feb-10 Page 1 of 4 www.power-one.com

Features

• RoHS lead-solder-exemption compliant

• Automatic 115/230 input voltage selection

• All outputs fully regulated

• Remote sense, overvoltage protection, and

overtemperature protection

• Power Fail signal included

• Greater than 100,000 Hour MTBF

• U-Channel chassis: 8.50" x 4.50" x 2.00"

(215.9mm x 114.3mm x 50.8mm)

• Optional cover

• Metric and SAE mounting inserts

Single Output Model Selection

MODEL OUTPUT ADJUSTMENT CONTINUOUS PEAK LINE LOAD TYPICAL RIPPLE & INITIAL SETTING

VOLTAGE RANGE CURRENT CURRENT (NOTE 3) REGULATION REGULATION NOISE %p-p (NOTE 1) ACCURACY

MAP130-1005 5V 4.75V to 5.50V 26A 30A 0.2% 1% 1% 5.1V to 5.2V

MAP130-1012 12V/15V 11.4V to 15.75V 12A/10A (Note 2) 13.8A/11A 0.2% 1% 1% 12.0V to 12.2V

MAP130-1024 24V/28V 22.5V to 30.0V 6.2A/5.4A (Note 2) 6.8A/5.9A 0.2% 1% 1% 23.9V to 24.1V

NOTES: 1) Typical peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.

2) MAP130-1012 output currents are expressed as 12V/15V operation. MAP130-1024 output currents are expressed as 24V/28V operation.

3) Peak load for 60 seconds or less are acceptable, 10% duty cycle, maximum.

Power-One’s MAP130 Series of single and multiple output power supplies provide fully-regulated outputs with high

peak current capabilities in a comp act 4.50" x 8.50" x 2.00" U-channel chassis. Other standard features include autos-

elect AC input, EMI level B filtering, power fail, thermal shutdown (with warning), remote sense, and metric and SAE

mounting inserts.

This convection-cooled series is designed for use in commercial and industrial environments in temperatures up to

50 °C. All products are approved to the latest international regulatory standards and display the CE Mark.

Description

Model numbers highlighted in yellow or shaded are not recommended for new designs.

Multiple Output Model Selection (Cont.)

–

130W Continuous Output Power

MODEL OUTPUT ADJUSTMENT OUTPUT PEAK CURRENT LINE LOAD TYPICAL RIPPLE & INITIAL SETTING

VOLTAGE RANGE CURRENT (NOTE 1) REGULATION REGULATION NOISE %p-p (NOTE 2) ACCURACY

+5V 4.75V to 5.50V 20A 30A 1% 1% 1% 5.1V to 5.2V

MAP130-4003 +15V 14.0V to 16.0V 4A 8A 1% 2% 1% 15.0V to 15.1V

-5V Fixed 1A 1A 2% 2% 1% -4.8V to -5.2V

-15V Fixed 1A 1A 2% 2% 1% -14.7V to -15.3V

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.15V to 5.2V

MAP130-4004 +24V 23.0V to 25.0V 3.5A 5A 0.5% 2% 1% 23.9V to 24.1V

-15V Fixed 1A 1A 0.5% 2% 1% -14.5V to -15.5V

+15V Fixed 1A 1A 0.5% 2% 1% 14.5V to 15.5V

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.1V to 5.25V

MAP130-4010 +12V 11.5V to 12.8V 5A 10A 0.5% 2% 1% 11.75V to 12.0V

-5V Fixed 1A 1A 0.5% 2% 1% -4.8V to -5.2V

-12V Fixed 3A 3A 0.5% 2% 1% -11.6V to -12.4V

+5V 4.75V to 5.50V 20A 30A 0.2% 1% 1% 5.1V to 5.25V

MAP130-4020 +12V 11.5V to 12.8V 5A 10A 0.5% 2% 1% 11.75V to 12.0V

-12V Fixed 1A 1A 0.5% 2% 1% -11.6V to -12.4V

-5V Fixed 3A 3A 0.5% 2% 1% -4.8V to -5.2V

NOTES: 1) Peak loads up to 165 Watts, (total of all outputs), for 60 seconds or less are acceptable, (10% duty cycle max.).

2) Maximum peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.

MAP130 AC-DC Series Data Sheet

MCD10115 Rev. 1.3, 05-Feb-10 Page 2 of 4 www.power-one.com

Input Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Input Voltage- AC Auto-ranging. Low Range 90 115 132 VAC

High Range 175 230 264

Input Frequency AC Input. 47 63 Hz

Brown out Protection Lowest AC input voltage that regulation is maintained with full rated loads. 90 VAC

Hold-up Time Nominal AC input voltage (115 VAC). 130W load: 40 mS

Input Current 90 VAC, 130W load. 3.3 ARMS

Input Protection Non-user serviceable internally located AC input line fuse.

Inrush Surge Current Internally limited by thermistor. Vin = 264 VAC (one cycle). 25° C. 38 APK

Operating Frequency Switching frequency of main transformer (variable). Range: 16 120 kHz

Output Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Efficiency Full Load, 115VAC. Varies with distribution of loads among outputs. 71 80 %

Minimum Loads MAP130-1012. 1.25

MAP130-1024. 0.63 Amps

MAP130-1005 and all multiple output models, main channel only. 3.00

Ripple and Noise Full load, 20MHz bandwidth. See Model Selection Chart

Output Power Continuous output power, all multiple output models. 130 Watts

Peak output power (60s maximum, 10% duty cycle), all multiple output models. 165

Overshoot /Undershoot Output voltage overshoot/undershoot at turn-on / turn-off 1 %

Regulation Varies by output, Total regulation includes: line changes from 90-132 VAC See Model Selection Chart

or 175-264, changes in load starting at 20% load and changing to 100% load.

Transient Response Recovery time to within 1% of initial set point due to a 50-100% load change, 500 µS

4% max. deviation. (Main output only on multi-output units)

Turn-on Delay Time required for initial output voltage stabilization. 2 Sec

Turn-on Rise Time Time required for output voltage to rise from 10% to 90%. 20 mS

Model numbers highlighted in yellow or shaded are not recommended for new designs.

MAP130 AC-DC Series Data Sheet

MCD10115 Rev. 1.3, 05-Feb-10 Page 3 of 4 www.power-one.com

Interface Signals and Internal Protection

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Overvoltage Protection Provided on single output units and only MAP130-1012 17.0 22.0

the main output of multiple output units. MAP130-1024 32.0 37.0 VDC

MAP130-4004 6.2 7.4

All other models. 5.5 6.8

Overcurrent Protection All models have inherent short circuit protection. Units will automatically restart at the removal of the fault.

Remote Sense Total voltage compensation for main output cable losses. 250 mV

Logic LO (denotes power fail detected). 0.7 V

Power Fail Warning Logic HI with internal pull-up to output. 10 k⍀

(Note 1) Power Fail trip point, maximum load, decreasing line. 86 94 VAC

Time before regulation dropout, at full load, due to loss of input power. 5 mS

Overtemperature Warning Warning prior to system shutdown due to excessive internal temperatures. 20 mS

(Note 2) Shifts Power Fail signal to a logic LO state.

NOTES: 1) Power Fail not available on MAP130-1012 and MAP130-1024.

2) MAP130-1012 and MAP130-1024 have overtemperature protection, but do not have the warning feature.

Safety, Regulatory, and EMI Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Agency Approvals UL1950.

CSA 22.2 No. 234/950. Approved

EN60950 (TÜV).

Dielectric Withstand Voltage Input to Output, 1 second. 2600 VDC

Electromagnetic FCC CFR title 47 Part 15 Sub-Part B - Conducted B

Interference, EN55022 / CISPR 22 Conducted B Class

EN55022 / CISPR 22 Radiated (Note 1) B

ESD Susceptibility Per EN61000-4-2, level 4 8 kV

Radiated Susceptibility Per EN61000-4-3, level 3 10 V/M

EFT/Burst Per EN61000-4-4, level 3 (Note 2) ±2 kV

Input Transient Protection Per EN61000-4-5 class 3 Line to Line 1 kV

Line to Ground 2

Insulation Resistance Input to output 7 M⍀

Leakage Current Per EN60950 (264 VAC) 700 µA

NOTES: 1) MAP130-1005 meets Class A, radiated.

2) MAP130-1005, MAP130-4003, and MAP130-4010, meet level 2, ±1kV.

Environmental Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Altitude Operating 10K Feet

Non-Operating 40K

Operating Temperature At 100% load: 0 50 °C

Derate linearly above 50°C by 2.5% per °C At 50% load: 70 °C

Storage Temperature -40 85 °C

Temperature Coefficient 0°C to 70°C (after 15 minute warm-up period) ±0.02 ±0.05 %/°C

Relative Humidity Non-Condensing 5 95 %RH

Shock Operating, peak acceleration 20 GPK

Vibration Random vibration, 10Hz to 2kHz, 3 axis 6 GRMS

Options

DESCRIPTION NOTES DIMENSIONS

Cover Add ‘C’ suffix to model number or order part number 412-59586-G separately.

For convection cooled applications with covers, derate output power as follows: 8.50" x 4.50" x 2.40"

Derate all multiple output models and MAP130-1005 to 120 watts. (215.9mm x 114.3mm x 61.0mm)

Derate MAP130-1012 and MAP130-1024 to 140 watts.

MAP130 AC-DC Series Data Sheet

MCD10115 Rev. 1.3, 05-Feb-10 Page 4 of 4 www.power-one.com

OVERALL SIZE: 8.50" x 4.50" x 2.00" (215.9mm x 114.3mm x 50.8mm)

WEIGHT: 2.5 lb (1.13 kg)

NUCLEAR AND MEDICALAPPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components

in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective

divisional president of Power-One, Inc.

TECHNICAL REVISIONS - The appearance of product s, including safety agency certifications pictured on labels, may change depending on the date

manufactured. Specifications are subject to change without notice.

INPUT & OUTPUT CONNECTIONS: 6-32 SCREW WIRE CLAMPS ON 0.312" (7.9mm) CENTERS,

0.045" (1.1mm) SQUARE PINS ON 0.156" (3.96mm) CENTERS;

MATES WITH MOLEX SERIES 2139, 6442, & 41695

POWER FAIL CONNECTIONS, J2: 0.035" (0.89mm) SQUARE PINS ON 0.100" (2.54mm) CENTERS;

MATES WITH MOLEX SERIES 2695 & 6471

CHASSIS: 0.090" (2.286mm) ALUMINUM ALLOY WITH CLEAR FINISH