© Semiconductor Components Industries, LLC, 2011
June, 2018 − Rev. 5 1Publication Order Number:
NCS2250/D
NCS2250, NCV2250,
NCS2252, NCV2252
Comparator, High Speed,
50 ns, Low Voltage,
Rail-to-Rail
The NCS2250 and NCS2252 low voltage comparators feature fast
response time and rail−to−rail input and output. The extended
common mode input voltage range allows input signals 200 mV above
and below the rails, allowing voltage detection at ground or the supply.
A propagation delay of 50 ns with a 100 mV overdrive makes this
comparator suitable for applications requiring faster response times.
These single channel devices are available with a complementary
push−pull output in the NCS2250 or with an open drain output in the
NCS2252. Both options are offered in TSOP−5 (SOT23−5) and
SC−88A (SC70−5) packages. Automotive qualified devices are also
available, denoted by the NCV prefix.
Features
•Propagation Delay: 50 ns with 100 mV Overdrive
•Rail−to−rail Input: VSS − 200 mV to VDD + 200 mV
•Supply Voltage: 1.8 V to 5.5 V
•Supply Current: 150 μA Typical at 5 V Supply
•Available with Push−pull or Open Drain Output
•Packages: TSOP−5 (SOT23−5) and SC−88A (SC70−5)
•NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
•These Devices are Pb−free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
•Voltage Threshold Detector
•Zero−crossing Detectors
•High−speed Sampling Circuits
•Logic Level Shifting / Translation
•Clock and Data Signal Restoration
End Products
•Automotive
•Lighting
•Smartphones, cell phones
•Portable and battery−powered systems
•Power supplies
www.onsemi.com
TSOP−5
(SOT23−5)
CASE 483
See detailed ordering and shipping information on page 2 o
f
this data sheet.
ORDERING INFORMATION
MARKING DIAGRAMS
SCALE 2:1
1
5
SCALE 2:1
SC−88A
(SC70−5)
CASE 419A−02
XX MG
G
XX = Specific Device Code
A = Assembly Location
Y = Year
W = Work Week
M = Date Code
G= Pb−Free Package
(Note: Microdot may be in either location)
1
5
XX AYWG
G
PIN DIAGRAM
1
2
34
5
OUT
VSS
IN+ IN−
TSOP−5 (SOT23−5) and
SC−88A (SC70−5) pinout
VDD
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
2
Table 1. ORDERING INFORMATION
Automotive Output Device (Note 1) Package Marking Shipping †
No Push−Pull NCS2250SQ2T2G SC−88A (SC70−5) 5C 3000 / Tape & Reel
NCS2250SN2T1G TSOP−5 (SOT23−5) 5A 3000 / Tape & Reel
Open Drain NCS2252SQ2T2G SC−88A (SC70−5) 5F 3000 / Tape & Reel
NCS2252SN2T1G TSOP−5 (SOT23−5) 5D 3000 / Tape & Reel
Yes Push−Pull NCV2250SQ2T2G SC−88A (SC70−5) 5C 3000 / Tape & Reel
NCV2250SN2T1G TSOP−5 (SOT23−5) 5A 3000 / Tape & Reel
Open Drain NCV2252SQ2T2G SC−88A (SC70−5) 5F 3000 / Tape & Reel
NCV2252SN2T1G TSOP−5 (SOT23−5) 5D 3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
1. Contact local sales office for more information.
Table 2. PIN DESCRIPTION
Name Type Description
VDD Power Positive supply pin. Connect to positive rail. A bypass capacitor of at least 0.1 μF is
recommended as close as possible to the VDD pin
VSS Power Negative supply pin. Connect to ground or negative rail. If not connected to ground,
a bypass capacitor of at least 0.1 μF is recommended as close as possible to the VSS pin
OUT Output Output pin. NCS2250 has a complementary push−pull output stage. NCS2252 has an open
drain output stage which requires an external pull−up resistor
IN− Input Inverting input
IN+ Input Non−inverting input
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
3
Table 3. ABSOLUTE MAXIMUM RATINGS (Note 2)
Rating Symbol Value Units
Supply Voltage Range (VDD − VSS) VS0 to 6 V
Input Voltage Range VIN VSS − 0.3 to VDD + 0.3 V
Output Voltage Range VOVSS − 0.3 to VDD + 0.3 V
Output Short Circuit Current (Note 3) ISC Continuous mA
Maximum Junction Temperature (Note 4) TJ(max) +150 °C
Storage Temperature Range Tstg −65 to +150 °C
ESD Capability (Note 5)
Human Body Model
Machine Model HBM
MM 2000
50
V
Latch−up Current (Note 6) ILU 100 mA
Moisture Sensitivity Level (Note 7) MSL Level 1
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be af fected.
2. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
3. Applies to both single−supply and split−supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±50 mA over long term may adversely affect
reliability.
4. See APPLICATION INFORMATION for Safe Operating Area.
5. This device series incorporates ESD protection and is tested by the following methods:
− ESD Human Body Model tested per JEDEC standard JESD22−A114 (AEC−Q100−002)
− ESD Machine Model tested per JEDEC standard JESD22−A115 (AEC−Q100−003)
6. Latch−up Current per JEDEC standard JESD78.
7. Moisture Sensitivity Level tested per IPC/JEDEC standard J−ST−020A.
Table 4. THERMAL INFORMATION
Parameter Symbol Package Single Layer Board
(Note 8) Units
Junction−to−Ambient
Thermal Resistance qJA TSOP−5 (SOT23−5) 150 °C/W
SC−88A (SC70−5) 162
8. Values based on a single layer 1S standard PCB with 1.0 oz copper and a 50 mm2 copper area.
Table 5. OPERATING RANGES (Note 9)
Parameter Symbol Min Max Units
Power Supply Voltage VS1.8 5.5 V
Input Common Mode Voltage Range VCM VSS – 0.2 VDD + 0.2 V
Ambient Temperature TA−40 125 °C
9. See APPLICATION INFORMATION for Safe Operating Area.
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
4
Table 6. ELECTRICAL CHARACTERISTICS AT 5 V SUPPLY
Typical values are referenced to TA = 25°C, VDD = 5 V, VSS = 0 V, VCM = mid−supply, CL = 50 pF, unless otherwise noted. NCS2252 is
connected to RPULL−UP = 10 kΩ to VDD, unless otherwise noted. Boldface numbers apply from TA = −40°C to 125°C (Notes 10, 11)
Parameter Test Conditions Symbol Min Typ Max Units
SUPPLY CHARACTERISTICS
Quiescent Supply Current No load IDD 150 200 μA
250
Power Supply Rejection Ratio PSRR 88 dB
62.5
INPUT CHARACTERISTICS
Input Offset Voltage VOS 0.5 6 mV
6
Input Bias Current (Note 11) IIB 20 pA
1000
Input Offset Current (Note 11) IOS 20 pA
1000
Common Mode Rejection Ratio CMRR 81 dB
59
Input Capacitance CIN 3.8 pF
OUTPUT CHARACTERISTICS
Output Voltage High NCS2250, IOUT = 4 mA VOH VDD – 0.1 V
VDD – 0.3
Output Voltage Low IOUT = 4 mA VOL VSS + 0.09 V
VSS + 0.3
Output Current Capability NCS2250, Sourcing IO48 mA
Sinking 52
Output Leakage Current NCS2252, VS = 5.5 V ILEAK 1 nA
Output Rise Time NCS2250, 10% to 90%, VOD = 100 mV trise 4 ns
Output Fall Time NCS2250, 90% to 10%, VOD = 100 mV tfall 4ns
NCS2252, 90% to 10%, VOD = 100 mV 5.5
Propagation Delay (Note 11) NCS2250 VOD = 100 mV tpLH, tpHL 50 64 ns
VOD = 50 mV 60
VOD = 20 mV 90
NCS2252
(Note 12) VOD = 100 mV tpHL 50 64 ns
VOD = 50 mV 60
VOD = 20 mV 90
Propagation Delay Skew
(NCS2250) VOD = 100 mV, CL = 50 pF tSKEW 6ns
VOD = 50 mV, CL = 50 pF 2
VOD = 20 mV, CL = 50 pF 1
10.Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
11.Performance guaranteed over the indicated operating temperature range by design and/or characterization.
12.Typical values are provided for NCS2252 output high−to−low propagation delay. NCS2252 is an open drain comparator. Output low−to−high
propagation delay is a function of the RC time constant, which is dependent on the pull−up resistor.
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
5
Table 7. ELECTRICAL CHARACTERISTICS AT 1.8 V SUPPLY
Typical values are referenced to TA = 25°C, VDD = 1.8 V, VSS = 0 V, VCM = mid−supply, CL = 50 pF, unless otherwise noted. NCS2252 is
connected to RPULL−UP = 10 kΩ to VDD, unless otherwise noted. Boldface numbers apply from TA = −40°C to 125°C (Notes 13, 14)
Parameter Test Conditions Symbol Min Typ Max Units
SUPPLY CHARACTERISTICS
Quiescent Supply Current No load IDD 145 200 μA
250
Power Supply Rejection Ratio PSRR 82 dB
62.5
INPUT CHARACTERISTICS
Input Offset Voltage VOS 0.5 6 mV
6
Input Bias Current (Note 14) IIB 20 pA
1000
Input Offset Current (Note 14) IOS 20 pA
1000
Common Mode Rejection Ratio CMRR 76 dB
55
Input Capacitance CIN 4.4 pF
OUTPUT CHARACTERISTICS
Output Voltage High NCS2250, IOUT = 4 mA VOH VDD – 0.14 V
VDD – 0.3
Output Voltage Low IOUT = 4 mA VOL VSS + 0.12 V
VSS + 0.3
Output Current Capability NCS2250, Sourcing IO25 mA
Sinking 42
Output Leakage Current NCS2252, VS = 5.5 V ILEAK 1 nA
Output Rise Time NCS2250, 10% to 90%, VOD = 100 mV trise 7 ns
Output Fall Time NCS2250, 90% to 10%, VOD = 100 mV tfall 6ns
NCS2252, 90% to 10%, VOD = 100 mV 7
Propagation Delay (Note 14) NCS2250 VOD = 100 mV tpLH, tpHL 56 68 ns
VOD = 50 mV 71
VOD = 20 mV 106
NCS2252
(Note 15) VOD = 100 mV tpHL 56 68 ns
VOD = 50 mV 71
VOD = 20 mV 106
Propagation Delay Skew
(NCS2250) VOD = 100 mV, CL = 50 pF tSKEW 5ns
VOD = 50 mV, CL = 50 pF 2
VOD = 20 mV, CL = 50 pF 1
13.Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
14.Performance guaranteed over the indicated operating temperature range by design and/or characterization.
15.Typical values are provided for NCS2252 output high−to−low propagation delay. NCS2252 is an open drain comparator.
Output low−to−high propagation delay is a function of the RC time constant, which is dependent on the pull−up resistor.
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
6
GRAPHS
Typical performance at TA = 25°C, unless otherwise noted.
Figure 1. Transient Response at 5 V Supply
with Varying Input Overdrive Voltages Figure 2. Transient Response at 5 V Supply
with Varying Input Overdrive Voltages
Figure 3. Transient Response at 1.8 V Supply
with Varying Input Overdrive Voltages Figure 4. Transient Response at 1.8 V Supply
with Varying Input Overdrive Voltages
Figure 5. Output High−to−Low Propagation Delay
vs. Input Overdrive Voltage Figure 6. Output Low−to−High Propagation Delay
vs. Input Overdrive Voltage
−5
−4
−3
−2
−1
0
1
2
3
4
5
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
−25 0 25 50 75 100 125 150 175 200
Output (V)
Input (V)
Time (ns)
Input
20 mV
50 mV
100 mV
VS = 5 V
CL = 50 pF
INPUT
OUTPUT
−5
−4
−3
−2
−1
0
1
2
3
4
5
−25 0 25 50 75 100 125 150 175 200
Output (V)
Input (V)
Time (ns)
Input
20 mV
50 mV
100 mV
VS = 5 V
CL = 50 pF
INPUT
OUTPUT
−1.5
−1.0
−0.5
0.0
0.5
1.0
1.5
−0.3
−0.2
−0.1
0
0.1
0.2
0.3
−25 0 25 50 75 100 125 150 175 200
Output (V)
Input (V)
Time (ns)
Input
20 mV
50 mV
100 mV
VS = 1.8 V
CL = 50 pF
INPUT
OUTPUT −1.5
−1.0
−0.5
0.0
0.5
1.0
1.5
−0.15
−0.1
−0.05
0
0.05
0.1
0.15
−25 0 25 50 75 100 125 150 175 200
Output (V)
Input (V)
Time (ns)
Input
20 mV
50 mV
100 mV
INPUT OUTPUT
0
20
40
60
80
100
120
140
160
020406080100
Propagation Delay (ns)
Input Overdrive Voltage (mV)
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
Output low−to−high
CL = 50 pF
0
20
40
60
80
100
120
140
160
020406080100
Propagation Dleay (ns)
Input Overdrive Voltage (mV)
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
Output high−to−low
CL = 50 pF
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
NCS2250
VS = 1.8 V
CL = 50 pF
NCS2250
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
7
GRAPHS (continued)
Typical performance at TA = 25°C, unless otherwise noted.
Figure 7. Output High−to−Low Propagation Delay
vs. Load Capacitance Figure 8. Output Low−to−High Propagation Delay
vs. Load Capacitance
−20
−15
−10
−5
0
5
10
15
20
−0.2 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
Input Current (pA)
Common Mode Voltage (V)
IIB+
IIB−
Vs = 1.8 V
T = 25°C
−20
−15
−10
−5
0
5
10
15
20
−0.2 0.4 1 1.6 2.2 2.8 3.4 4 4.6 5.2
Input Current (pA)
Common Mode Voltage (V)
IIB+
IIB−
Vs = 5 V
Figure 9. Input Current vs. Common Mode
Voltage at 1.8 V Supply Figure 10. Input Current vs. Common Mode
Voltage at 5 V Supply
50
60
70
80
90
100
110
120
130
140
10 20 30 40 50 60 70 80 90 100
Propagation Delay (ns)
Load Capacitance (pF)
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
50
60
70
80
90
100
110
120
130
140
10 20 30 40 50 60 70 80 90 100
Propagation dleay (ns)
Load Capacitance (pF)
Vs = 1.8 V
Vs = 3 V
Vs = 5 V
Output low−to−high
20 mV overdrive
Figure 11. Input Current vs. Temperature
at 1.8 V Supply Figure 12. Input Current vs. Temperature
at 5 V Supply
T = 25°C
−50
−25
0
25
50
75
100
125
150
175
200
225
−50 −25 0 25 50 75 100 125
Input Current (pA)
IIB−
IIB+
IOS
Vs = 1.8 V
−50
−25
0
25
50
75
100
125
150
175
200
225
−50 −25 0 25 50 75 100 125
Input Current (pA)
IIB−
IIB+
IOS
Vs = 5 V
Temperature (°C) Temperature (°C)
Output high−to−low
20 mV overdrive NCS2250
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
8
GRAPHS (continued)
Typical performance at TA = 25°C, unless otherwise noted.
Figure 13. Output Voltage High (Relative to VDD)
vs. Output Current Figure 14. Output Voltage Low (Relative to VSS)
vs. Output Current
0
01020304050
Output Current (mA)
Vs = 5 V
Vs = 1.8 V
Figure 15. Output Current Capability vs. Temperature Figure 16. Supply Current vs. Temperature
−60
−40
−20
0
20
40
60
80
−50 −25 0 25 50 75 100 125
Output Current Capability (mA)
Vs = 1.8 V
Vs = 5 V
Vs = 1.8 V
Vs = 5 V
SOURCING (NCS2250)
SINKING
100
110
120
130
140
150
160
170
180
−50 −25 0 25 50 75 100 125
Supply Current (μA)
Vs = 1.8 V
Vs = 5 V
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0 5 10 15 20 25 30 35 40
VDD−VOH (V)
Output Current (mA)
Vs = 5 V
Vs = 1.8 V
VOL−VSS (V)
Temperature (°C) Temperature (°C)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
NCS2250
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
9
APPLICATION INFORMATION
Input Stage
The NCS2250 and NCS2252 have rail−to−rail inputs. The
input common mode voltage range of these comparators
extend 200 mV beyond the rails, allowing voltage sensing
at ground or at the supply voltage.
Output Stage
The NCS2250 has a complementary, push−pull output
stage. When the output transitions between high and low
states, a low resistance path is created between the positive
and negative supply rails, temporarily increasing the supply
current during the transition.
The NCS2252 has an open−drain output stage. This
allows the output to be connected through a pull−up resistor
to another supply voltage for applications where level
translation or level shifting is needed. The output resistor
can be connected to voltages below VDD or up to VDD + 0.3
V. Since the NCS2252 relies on an external pull−up resistor
to provide sourcing current, the timing of the output
low−to−high transition is determined by the RC time
constant of the pull−up resistor and the load capacitance.
Hysteresis
When the inputs are near the same voltage, slight voltage
fluctuations due to noise can cause the output to oscillate
between high and low states. If noise−induced switching
behavior is observed at the output, hysteresis should be
added through an external resistor network. This is
particularly the case for NCS2250, as sustained output
oscillations causing increased supply current will result in
elevated junction temperature.
Hysteresis can be added to the circuit by adding one or two
external resistors depending on whether an inverting or
non−inverting configuration is needed. Figure 17 shows the
inverting configuration. In this configuration, the output
voltage adjusts the threshold at the IN+ pin.
Figure 17. Comparator with Hysteresis, Inverting Configuration
+
−
NCS2250
RF
R1
R2VIN
For the inverting configuration, the value of the
high−level input voltage which triggers the output to switch
from high to low is given by the following equation:
VIN_high +R1 RF
R1 RF)R1 R2)R2 RF VDD (eq. 1)
The value of the low−level input voltage which triggers
the output to switch from low to high is given by the
following equation:
VIN_low +R1 RF)R1 R2
R1 RF)R1 R2)R2 RF VDD (eq. 2)
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
10
Figure 18 shows the non−inverting configuration. For the
non−inverting configuration, the threshold Vth set by R1 and
R2 is fixed. The output adjusts the input signal on IN+.
Figure 18. Comparator with Hysteresis, Non−Inverting
Configuration
RF
R1
R2
VIN +
−
NCS2250
RIN
The value of the high−level input voltage which triggers
the output to switch from low to high is given by the
following equation:
VIN_high +Vth (RIN )RF)
RF(eq. 3)
The value of the low−level input voltage which triggers
the output to switch from high to low is given by the
following equation:
VIN_low +Vth (RIN )RF)*RIN VDD
RF(eq. 4)
Power dissipation
The absolute maximum junction temperature is 150°C.
The junction temperature can be calculated using the power
dissipation P, thermal resistance qJA, and ambient
temperature TA.
TJ+qJA P)TA(eq. 5)
Layout Techniques
High speed layout techniques are recommended for the
best performance.
Bypass capacitors of at least 0.1 mF must be placed as
close as possible to supply pins.
The traces on the input pins should be short to minimize
any noise on the high impedance inputs. In general, shorter
traces will reduce parasitic capacitance, inductance, and
resistance.
Identify and keep sensitive traces away from possible
noise sources such as clocks. Crosstalk can be reduced by
increasing the distance between traces. Do not let traces run
parallel for long distances. Take advantage of routing layers
to separate traces that would otherwise run parallel. Ground
or DC voltage supplies can be used to separate a sensitive
trace from a noise source.
Avoid floating nodes as these will pick up noise.
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
11
PACKAGE DIMENSIONS
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
DIM
A
MIN MAX MIN MAX
MILLIMETERS
1.80 2.200.071 0.087
INCHES
B1.15 1.350.045 0.053
C0.80 1.100.031 0.043
D0.10 0.300.004 0.012
G0.65 BSC0.026 BSC
H--- 0.10---0.004
J0.10 0.250.004 0.010
K0.10 0.300.004 0.012
N0.20 REF0.008 REF
S2.00 2.200.079 0.087
B0.2 (0.008) MM
12 3
45
A
G
S
D 5 PL
H
C
N
J
K
−B−
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
ǒmm
inchesǓ
SCALE 20:1
0.65
0.025
0.65
0.025
0.50
0.0197
0.40
0.0157
1.9
0.0748
SOLDER FOOTPRINT
NCS2250, NCV2250, NCS2252, NCV2252
www.onsemi.com
12
TSOP−5 / (SOT23−5)
CASE 483
ISSUE M
0.7
0.028
1.0
0.039
ǒmm
inchesǓ
SCALE 10:1
0.95
0.037
2.4
0.094
1.9
0.074
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
DIM MIN MAX
MILLIMETERS
A
B
C0.90 1.10
D0.25 0.50
G0.95 BSC
H0.01 0.10
J0.10 0.26
K0.20 0.60
M0 10
S2.50 3.00
123
54 S
AG
B
D
H
CJ
__
0.20
5X
CAB
T0.10
2X
2X T0.20
NOTE 5
CSEATING
PLANE
0.05
K
M
DETAIL Z
DETAIL Z
TOP VIEW
SIDE VIEW
A
B
END VIEW
1.35 1.65
2.85 3.15
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor ’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer ’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body . Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
NSC2250/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative
◊
