MCP2150 Developer's Board User's Guide (c) 2009 Microchip Technology Inc. DS51869A Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS51869A-page 2 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Table of Contents Preface ........................................................................................................................... 5 Introduction............................................................................................................ 5 Document Layout .................................................................................................. 6 Conventions Used in this Guide ............................................................................ 7 Recommended Reading........................................................................................ 8 The Microchip Web Site ........................................................................................ 8 Customer Support ................................................................................................. 8 Document Revision History ................................................................................... 9 Chapter 1. Product Overview 1.1 Introduction And Highlights .......................................................................... 11 1.2 What is the MCP2150 Developer's Board? .................................................. 11 1.3 MCP2150 Developer's Board Features ........................................................ 12 1.4 PC Requirements ......................................................................................... 17 1.5 What the MCP2150 Developer's Board Kit includes .................................... 17 Chapter 2. Installation and Operation 2.1 Introduction ................................................................................................... 19 2.2 The Demo System ........................................................................................ 20 2.3 MCP2150DM Demos ................................................................................... 21 Appendix A. Schematic and Layouts A.1 Introduction .................................................................................................. 35 A.2 Board - Schematic - Page 1 ......................................................................... 36 A.3 Board - Schematic - Page 2 ......................................................................... 37 A.4 Board - Top Silk and Pads ........................................................................ 38 A.5 Board - Top Layer ...................................................................................... 39 A.6 Board - Top Layer with Silk and Pads ....................................................... 40 A.7 Board - Bottom Layer ................................................................................ 41 A.8 Board - Power Layer ................................................................................... 42 A.9 Board - Ground Layer ............................................................................... 43 Appendix B. Bill Of Materials (BOM) Appendix C. Board Testing C.1 What is Tested ............................................................................................. 49 C.2 What is NOT Tested .................................................................................... 50 Appendix D. Configuring the HyperTerminal(R) Program D.1 Configuring the Hyperterminal(R) Program .................................................... 51 (c) 2009 Microchip Technology Inc. DS51869A-page 3 MCP2150 Developer's Board User's Guide Appendix E. Continuously Transmitted Data Table E.1 Data Table for Demo #2 ............................................................................... 61 Appendix F. Programming the MCP2150DM Worldwide Sales and Service .....................................................................................64 DS51869A-page 4 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Preface NOTICE TO CUSTOMERS All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available. Documents are identified with a "DS" number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is "DSXXXXXA", where "XXXXX" is the document number and "A" is the revision level of the document. For the most up-to-date information on development tools, see the MPLAB(R) IDE on-line help. Select the Help menu, and then Topics to open a list of available on-line help files. INTRODUCTION This chapter contains general information that will be useful to know before using the MCP2150 Developer's Board. Items discussed in this chapter include: * * * * * * Document Layout Conventions Used in this Guide Recommended Reading The Microchip Web Site Customer Support Document Revision History (c) 2009 Microchip Technology Inc. DS51869A-page 5 MCP2150 Developer's Board User's Guide DOCUMENT LAYOUT This document describes how to use the MCP2150 Developer's Board. The manual layout is as follows: * Chapter 1. "Product Overview" - Important information about the MCP2150 Developer's Board. * Chapter 2. "Installation and Operation" - Includes instructions on how to get started with this user's guide and a description of the user's guide. * Appendix A. "Schematic and Layouts" - Shows the schematic and layout diagrams for the MCP2150 Developer's Board. * Appendix B. "Bill Of Materials (BOM)" - Lists the parts used to build the MCP2150 Developer's Board. * Appendix C. "Board Testing" - Discusses what is and is not tested on the MCP2150 Developer's Board. * Appendix D. "Configuring the HyperTerminal(R) Program" - Gives aid in the configuration of the HyperTerminal application. * Appendix E. "Continuously Transmitted Data Table" - Shows the data table that the MCP2150 Developer's Board transmits. * Appendix F. "Programming the MCP2150DM" - Gives information to assist in the programming of the MCP2150 Developer's Board. DS51869A-page 6 (c) 2009 Microchip Technology Inc. Preface CONVENTIONS USED IN THIS GUIDE This manual uses the following documentation conventions: DOCUMENTATION CONVENTIONS Description Arial font: Italic characters Represents Examples Referenced books Emphasized text A window A dialog A menu selection A field name in a window or dialog A menu path MPLAB(R) IDE User's Guide ...is the only compiler... the Output window the Settings dialog select Enable Programmer "Save project before build" A dialog button A tab A number in verilog format, where N is the total number of digits, R is the radix and n is a digit. A key on the keyboard Click OK Click the Power tab 4`b0010, 2`hF1 Italic Courier New Sample source code Filenames File paths Keywords Command-line options Bit values Constants A variable argument Square brackets [ ] Optional arguments Curly brackets and pipe character: { | } Ellipses... Choice of mutually exclusive arguments; an OR selection Replaces repeated text #define START autoexec.bat c:\mcc18\h _asm, _endasm, static -Opa+, -Opa0, 1 0xFF, `A' file.o, where file can be any valid filename mcc18 [options] file [options] errorlevel {0|1} Initial caps Quotes Underlined, italic text with right angle bracket Bold characters N`Rnnnn Text in angle brackets < > Courier New font: Plain Courier New Represents code supplied by user (c) 2009 Microchip Technology Inc. File>Save Press <Enter>, <F1> var_name [, var_name...] void main (void) { ... } DS51869A-page 7 MCP2150 Developer's Board User's Guide RECOMMENDED READING This user's guide describes how to use MCP2150 Developer's Board. Other useful documents are listed below. The following Microchip documents are available and recommended as supplemental reference resources. * MCP2150 Data Sheet, "IrDA Standard Protocol Stack Controller Supporting DTE Applications", DS21655 * MCP2155 Data Sheet, "IrDA Standard Protocol Stack Controller Supporting DCE Applications", DS21690 This data sheet provides detailed information regarding the MCP2150 product family. You can also find important information in the following Microchip documents: * AN941 - "Programming Windows XP(R) for Embedded IR Applications", DS00941. * AN926 - "Programming the Pocket PC OS for Embedded IR Applications", DS00926 * AN927 - "Data Throughput and the MCP215X", DS00927. * AN923 - "Using the MCP2120 Developer's Board for IR Sniffing", DS00923. * AN888 - "Programming the Palm OSTM for Embedded IR Applications", DS00888. * AN858 - "Interfacing the MCP215X to a Host Controller", DS00858. THE MICROCHIP WEB SITE Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com. DS51869A-page 8 (c) 2009 Microchip Technology Inc. Preface DOCUMENT REVISION HISTORY Revision A (October 2009) * Initial Release of this Document. (c) 2009 Microchip Technology Inc. DS51869A-page 9 MCP2150 Developer's Board User's Guide NOTES: DS51869A-page 10 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Chapter 1. Product Overview 1.1 INTRODUCTION AND HIGHLIGHTS This chapter provides an overview of the MCP2150 Developer's Boards' features, the system configurations that can be used in and the system requirements for the tutorials. Items discussed in this chapter are: * * * * 1.2 What is the MCP2150 Developer's Board? MCP2150 Developer's Board Features PC Requirements What the MCP2150 Developer's Board Kit includes WHAT IS THE MCP2150 DEVELOPER'S BOARD? The MCP2150 Developer's Board allows for the easy demonstration and development of IrDA applications. The board can be powered via USB or the power test points (VDD and GND). When using the power test points, if JP2 is shorted, the voltage must not exceed the PIC18F65J50 voltage specification. The Host interface can be connected to the UART driver device for communication over the DB-9 connector (for IrDA to UART operation), connected to the PIC18F65J50 for stand alone operation, or connected to the PIC18F65J50 with the PIC18F65J50 connected to the UART driver device (for pass-through operation). The USB interface signals are fully connected to the PIC18F65J50, so programs can be created where the PIC18F65J50 can communicate to the USB Host and to the MCP2150. This would allow the board to be used as an IrDA to USB converter. (c) 2009 Microchip Technology Inc. DS51869A-page 11 MCP2150 Developer's Board User's Guide 1.3 MCP2150 DEVELOPER'S BOARD FEATURES The MCP2150 Developer's Board has five functional blocks. These are: * * * * * Power Host Microcontroller MCP2150 Optical Transceiver circuitry RS-232 circuitry/interface The MCP2150 Developer's Board power can come from either the USB connection or the power test points. The USB power is regulated to 3.3V, due to requirements from the PIC18F65J50. To allow the other circuitry to operate at higher voltages, the MCP2150 Developer's Board has two power planes. One for the PIC18F65J50 circuitry and the other for the MCP2150/Optical Transceiver/RS-3238 Driver circuitry. An LED is used to indicate when power is applied to the MCP2150/Optical Transceiver/RS-232 Driver circuitry. A jumper (JP2) is used to tie the two power planes together. The MCP2150 uses a standard 11.0592 MHz crystal as the device clock. The Host Controller can be programmed via the ICSP interface with user developed programs. CAUTION The PIC18F65J50 has a maximum operational voltage of 3.6V. If the MCP2150 Developer's Board is powered by the VDD and GND Test Points, then care must be taken to ensure that the PIC18F65J50 is not over voltaged. The PIC18F65J50 can be isolated from the MCP2150's power plane by removing the jumper shunt on jumpers JP1 and JP2. The MCP2150DM has the MCP2150 device mounted on the PCB (TSSOP package). There is a DIP footprint (requires the TSSOP package to be removed) which allows the MCP2150 to be easily updated if a device revision occurs. The board supports up to four optical transceivers circuit implementations. Two implementation share the same general circuit layout. Only one optical transceiver circuit is installed at the time of manufacture. The others are for user implementation and evaluation. Jumpers are used to select the optical transceiver that is used by the system. A MAX3238 compatible level-shifting IC has all the necessary hardware to support connection of a RS-232 host through the DB-9 connector. The port can be connected to a PC using a straight-through cable. Refer to the MCP2150 Data Sheet (DS21655) for more information on the Host Interface signals. NOTICE Due to the flexibility of the interface between the MCP2150 and the PIC18F65J50, the board has limited support for the MCP2155 device. This board's firmware does not support the MCP2155. To better understand the MCP2155's Host Interface operation, please refer to the MCP215X/40 Data Logger Demo Board (MCP215XDM) firmware. DS51869A-page 12 (c) 2009 Microchip Technology Inc. Product Overview The MCP2150 Developer's Board, as shown in Figure 1-1, has the following hardware features: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Mini USB connector (for powering the board). On Board +3.3V regulator for powering PIC18F65J50. Hooks for an external regulated DC supply. Jumper to Isolate PIC18F65J50 power signal from rest of board power. This allows the board to operate at voltages higher than 3.3V. DB-9 connector and associated hardware for direct connection to MCP2150 UART (DB-9 interface requires RS-232 signal levels). Fourteen-pin header connection to Host UART interface. Fourteen 1x3 pin jumpers for routing of the UART signals between the MCP2150, PIC18F65J50, and MAX3238 devices. MCP2150 BAUD1:BAUD0 state jumpers. Green power-on indicator LED. Implemented IR transceiver circuit (two optional optical transceiver circuits implemented but not populated). Reset switch for PIC18F65J50 device. ICSP Header for PIC18F65J50. Jumper option for PIC18F65J50 program selection. PIC18F65J50 crystal. MCP2150 crystal socket. Carrier Detect (CD) indicator LED. MCP2150 SOIC and DIP Footprints (SOIC package is default installation. To install the DIP package requires the removal of the SOIC package). Note: (c) 2009 Microchip Technology Inc. A schematic of the MCP2150 Developer's Board is shown in Section A.2 "Board - Schematic - Page 1" DS51869A-page 13 MCP2150 Developer's Board User's Guide FIGURE 1-1: MCP2150 DEVELOPER'S BOARD HARDWARE 14 11 12 2 13 BOARD EDGE 1 7 4 5 9 DS51869A-page 14 3 15 6 17 8 16 10 (c) 2009 Microchip Technology Inc. Product Overview 1.3.1 Selecting Power Source, and Optical Transceiver Interface Jumper Descriptions Figure 1-2 shows the jumpers used to control the power source, and the optical transceiver used. Jumper JP2 connects to the boards two power planes. The MCP2150 Developer's Board has a power plane for the PIC18F65J50 and the related circuitry, and a second power plane for all other circuitry. Removing the jumper allows the MCP2150 portion to operate through the full voltage range of the MCP2150 (2.0V to 5.5V). When JP2 is connected, then the maximum voltage is restricted to the maximum voltage of the PIC18F65J50 device (3.6V). See Figure A.8 for the power plane layout. When JP2 is open, then the PIC18F65J50 must be isolated from the MCP2150. This is done with the JMP1:JMP14 jumpers as well as the R26, R27, R28, and R29 resistors. Jumpers JP1C1 and JP2C1 are used to connect the default installed optical transceiver to the MCP2150's RXPD and TXIR pins. There are footprints for two other optical transceiver implementations. If either of those implementations are installed, then the jumpers may be switched to the desired optical transceiver. FIGURE 1-2: MCP2150 SELECTING SOURCES BOARD EDGE This jumper isolates the PIC19's VDD from the MCP2150 VDD plane (see Section A.8 "Board - Power Layer") These two jumpers select the optical transceiver logic. Both jumpers should connect the same pin positions. JP2 JP1x1 and JP2x1 VDD's planes are connected Optical Transceiver connected to MCP2150 IR Interface VDD's planes are isolated Optical Transceiver not connected to MCP2150 IR Interface (c) 2009 Microchip Technology Inc. DS51869A-page 15 MCP2150 Developer's Board User's Guide 1.3.2 Host UART Interface Connection Jumper Descriptions Figure 1-3 shows the five jumpers used to control the connection of the MCP2150's Host UART signals. FIGURE 1-3: MCP2150 HOST UART INTERFACE CONNECTION BOARD EDGE These fourteen jumpers connect the MCP2150's Host UART Signals to either the PIC18F65J50 or the DB-9 connector (after the UART Driver device) MCP2150 Host Interface Baud Rate select Signals JP3:JP1 JMP1:JMP7 / JMP8:JMP14 Host Interface operates at 115,200 Baud Host Interface operates at 57,600 Baud Host UART Signals connected to PIC18F65J50 Host Interface operates at 19,200 Baud Host Interface operates at 9,600 Baud Note: Host UART Signals connected to UART Driver (DB-9) DS51869A-page 16 The PIC can also drive these signals. The supplied firmware uses PIC I/O to drive these signals based on the state of the RD5:4 pins. (c) 2009 Microchip Technology Inc. Product Overview 1.4 PC REQUIREMENTS The PC used has three main requirements. These are: 1. 2. 3. 4. Standard serial port. USB port (to power the MCP2150 Developer's Board). Terminal emulation program. IrDA standard driver installed, which treats the IR port as a virtual serial port. A non-legacy-free Intel(R) compatible model with Windows Operating System (OS) would meet these requirements. The Windows(R) OS includes a terminal emulation program called Hyperterminal. Section Appendix D. "Configuring the HyperTerminal(R) Program" shows instructions to configure HyperTerminal and demonstrate the developer's boards. 1.5 WHAT THE MCP2150 DEVELOPER'S BOARD KIT INCLUDES This MCP2150 Developer's Board kit includes: * MCP2150 Developer's Board, 102-00265 * Important Information Sheet NOTICE The Kits no longer ship with CD-ROMs. Any other material is available for download from the Developments Boards product page. This material can include such items as: * * * * User's Guide Firmware GUI programs Schematic Capture and PCB Layout files (c) 2009 Microchip Technology Inc. DS51869A-page 17 MCP2150 Developer's Board User's Guide NOTES: DS51869A-page 18 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Chapter 2. Installation and Operation 2.1 INTRODUCTION To demonstrate the operation of the MCP2150 Developer's Board (Secondary Device) a Primary Device is required. The Primary Device can be a PC with an IR port (integrated IR port or IR Dongle). The MCP2150 Developer's Board default firmware program has four different programs that are selected by the state of the RD7:6 pins. These demonstration programs have the following operation: * * * * Demo #1 Operation - Direct IR / UART (DB-9) Mode Demo #2 Operation - Data Streaming Mode Demo #3 Operation - Echo Data Mode Demo #4 Operation - IR / UART (DB-9) Pass Through PIC Mode Each demonstration program's operation will be described in the Demo section. The component layout floor plan of the MCP2150 Developer's Board (MCP2150DM) PCB is shown in Figure 1-1 while Table 2-1 shows the hardware requirements to demonstrate the MCP2150 Developer's Board. TABLE 2-1: DEMO SYSTEM HARDWARE REQUIREMENTS Qty 1 Hardware PC with: (1) a) IR port or PC with USB/Serial port and USB/Serial port to IR Dongle (1) b) One USB port to power the MCP2150 Developer's Board and c) one serial port to communicate to the MCP2150 Developer's Board. Purpose As a Primary Device, this device will initiate communication to the MCP2150 Developer's Board. The PC's USB port will also power the MCP2150 Developer's Board. Also: The PC's UART port will "talk" with the MCP2150's UART interface, while the PC's IR port will "talk" with the MCP2150's IR interface. The PC will run two instances of HyperTerminal, one connected to the PC's serial port (UART) and the other connected to the PC's IR port. 1 Serial Cable To connect the PC serial ports to the MCP2150 Developer's Board serial port. 1 USB Cable To power the MCP2150 Developer's Board from the PC's USB port. -- MCP2150 Developer's Board This is the demonstration unit Note 1: This can be done with one PC, but depending on the features of the selected PC, a second PC may be required due to number of serial ports available (see Figure 2-1). To keep the board cost low, only a portion of the MCP2150 Developer's Board is tested. This test covers the major portions of the system. The portions that are not tested are shown in Appendix C. "Board Testing". (c) 2009 Microchip Technology Inc. DS51869A-page 19 MCP2150 Developer's Board User's Guide 2.2 THE DEMO SYSTEM The demo system setup requires a Primary Device and a MCP2150 Developer's Board (Secondary Device). The Primary Device is a PC with an IR port (integrated IR port or IR Dongle). The Secondary Device is the embedded system, which is the MCP2150 Developer's Board. The MCP2150 Developer's Board can be powered by one of two sources: * The USB sourced power * The Power supply test points For the demo descriptions, the board will be powered via USB, so, a PC with a UART and USB port is required. The USB voltage is regulated to 3.3V, due to the PIC18 device's voltage operating range. This developer board either communicates between the DB-9 interface and the IR interface or acts as an embedded system and communicates between the IR interface and the PIC microcontroller. 2.2.1 The PIC18F65J50 Firmware The PIC18F65J50 firmware program looks at the state of the RD7:4 pins to determine the board's operation (program and Host UART baud rate). The configuration of the JMP14:JMP1 jumpers determines how the UART signals are connected between the MCP2150, PIC and the MAX3238 compatible driver. The programs have the following operations: * Data is directly passed from the IR interface to the MAX3238 device * Data is passed from the IR interface to the MAX3238 device after passing through the PIC microcontroller * Once a data byte has been received by the PIC, the PIC continuously streams a data table * The PIC echoes whatever character it receives, after changing the case (upper to lower, and lower to upper) 2.2.2 The PC with IR Port A PC with IR Port can be configured to operate as the Primary Device. The PC will need to run an appropriate application program to communicate with the Secondary Device. For a PC with IR port, this program will be HyperTerminal. The IRCOMM2K driver may need to be installed so that HyperTerminal can communicate to the IR port as if it was a serial port. When installing IRCOMM2K, select COM7 as the desired port. Configuring the HyperTerminal program on the PC is shown in D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)". The PC will run a second instance of HyperTerminal when running Demo #1 and Demo #4. This instance of HyperTerminal will communicate to the PC's serial port which will be connected to the MCP2150DM's serial port. This allows the transmitted data (from the IR port) to be seen on the serial port (and vice versa). Configuring the HyperTerminal program on the PC is shown in D.1.3 "HyperTerminal Configuration for the Secondary Device". Note: DS51869A-page 20 HyperTerminal should be disabled before establishing a connection between the PC and the MCP2150 Developer's Board. Make sure that any other programs (e.g., HotSync(R)) connected to the IR ports are disabled. (c) 2009 Microchip Technology Inc. Installation and Operation 2.3 MCP2150DM DEMOS A description of the demos, including step-by-step instructions are shown in this section. 2.3.1 Demo #1 Operation - Direct IR / UART (DB-9) Mode In Demo #1, the MCP2150 Developer's Board will communicate directly to the PC (or IrDA to serial interface Dongle) data received on the DB-9 port. This demo shows the MCP2150 converting data between the IR port and the Host UART port. The Primary Device's IR packet is decoded and any data is extracted and Transmitted on the Host UART interface. Data received on the Host UART interface is formatted into the IR data packet and transmitted to the Primary device. Figure 2-1 shows the system setup, while Figure 2-2 shows the jumper configuration for the MCP2150 board. Lastly, Table 2-2 shows the steps for Demo #1 operation. Note: Figure 2-3 shows an alternate jumper configuration where the MCP2150DM is powered via the VDD and GND test points (requires that JP2 shunt be removed). Table 2.3.2 does not document this configuration, but due to its similarities should be easy for the user to implement. DEMO #1 SYSTEM BLOCK DIAGRAM(1) FIGURE 2-1: HyperTerminal Program Window A (to IrDA Dongle) (1) (2) HyperTerminal Program Window B (Com 1) (2) Monitor Com 1 PC System #1 (1) Serial (UART or USB) to IrDA Dongle Note 1: (3) System #2 MCP2150 Developer's Board The PC may be a Notebook with an Integrated IR port. This operates as the Primary Device. 2: Serial cable. Connects Secondary Device to PC. 3: USB cable (for power only). Hyperterminal to Serial Port Settings The com port settings should be configured as: * * * * * 115,200 Baud 8-bits No Parity One Stop Hardware Flow Control (c) 2009 Microchip Technology Inc. DS51869A-page 21 MCP2150 Developer's Board User's Guide FIGURE 2-2: DEMO #1 CONFIGURATION - DIRECT TO UART (DB-9) MODE BOARD EDGE DB-9 Connector Note: DS51869A-page 22 IR Transceivers Data Flow This is the board configuration shipped to customers. (c) 2009 Microchip Technology Inc. Installation and Operation FIGURE 2-3: DEMO #1 ALTERNATE POWER CONFIGURATION BOARD EDGE GND Jumper Shunt Removed VDD DB-9 Connector (c) 2009 Microchip Technology Inc. Data Flow IR Transceivers DS51869A-page 23 MCP2150 Developer's Board User's Guide TABLE 2-2: DEMO #1 STEPS Step Action Result 1 Place the Primary Device's IR port and the MCP2150 Developer's Board on a flat surface about 25 cm (10 inches) apart, and with the IR ports facing each other. -- 2 On the MCP2150 Developer's Board: Ensure that the jumpers are configured as in Figure 2-2. -- 3 On the MCP2150 Developer's Board: On the MCP2150 Developer's Board: Apply power to the unit via the USB connector. The PIC The green power LED (D1) will turn on. reset switch (S1) may be depressed and released to ensure that the PIC had a good reset. 4 Connect PC's Serial Port to the DB-9 connector of the MCP2150 Developer's Board. -- 5 On the PC: Wait for the PC to make a sound and the system tray shows an IR Icon. Placing the mouse over the Icon will show the MCP2150 Device ID (currently "Generic IrDA"). -- 6 On the PC: Open the HyperTerminal program window for the Primary Device (such as COM 7). Ensure that the window indicates that the HyperTerminal program is connected. On the MCP2150 Developer's Board: -- Note: 7 See D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)" On the PC: The system tray Icon will change from a single IR Icon to two IR Icons facing each other. An IR Link is now established. On the PC: -- Open a second instance of HyperTerminal program window attached to the PC's Serial Port (such as COM 2) to connect to the MCP2150 Developer's Board. Ensure that the window indicates that the HyperTerminal program is connected. Note: See D.1.3 "HyperTerminal Configuration for the Secondary Device" 8 On the PC: In one of the HyperTerminal program windows (such as the Primary Device's window), type some characters. On the PC: In the other HyperTerminal program windows (the Serial Port window), those characters appear. 9 On the PC: In the other HyperTerminal program windows (Serial Port window), type some characters. On the PC: In the other HyperTerminal program windows (the Primary Device's window), those characters appear. 10 On the PC: In either HyperTerminal program windows, select the Transfer pull-down menu and then the Send Text File ... option. Navigate to the folder that contains the Transmit File.Txt file and select it. Then, click Open. On the PC: In the selected HyperTerminal program window, the displayed data is transmitted, being received and displayed by the other HyperTerminal program window. 11 On the PC: Make this file transfer transmitting from the other HyperTerminal program window. On the PC: In the selected HyperTerminal program window, the displayed data is transmitted, being received and displayed by the other HyperTerminal program window. 12 Continue steps 8, 9 10, or 11 for as long as desired. -- DS51869A-page 24 (c) 2009 Microchip Technology Inc. Installation and Operation 2.3.2 Demo #2 Operation - Data Streaming Mode In Demo #2, the MCP2150 Developer's Board (MCP2150DM) will communicate via the IR interface to the PC. The MCP2150DM is the Secondary Device, and will continuously stream a data table to the Primary Device (PC). This shows the data throughput from the embedded system to the Primary Device. This throughput will vary depending on the characteristics of the Primary Device. Figure 2-4 shows the system setup for this test, while Figure 2-5 shows the jumper configuration for the MCP2150 board. Lastly, Table 2-3 shows the steps for Demo #2 operation. Note: Figure 2-6 shows an alternate jumper configuration where the MCP2150DM is powered via the VDD and GND test points (requires that JP2 shunt be removed). Table 2-6 does not document this configuration but, due to its similarities, should be easy for the user to implement. DEMO #2 SYSTEM BLOCK DIAGRAM (1) FIGURE 2-4: HyperTerminal Program Window A (to IrDA Dongle) (1) (2) Monitor PC System #1 (1) Serial (UART or USB) to IrDA Dongle Note 1: 2: System #2 MCP2150 Developer's Board The PC may be a Notebook with an Integrated IR port. This operates as the Primary Device. USB cable (for power only). (c) 2009 Microchip Technology Inc. DS51869A-page 25 MCP2150 Developer's Board User's Guide FIGURE 2-5: DEMO #2 CONFIGURATION - DATA STREAMING MODE BOARD EDGE PIC18F65J50 Da ta ow Fl IR Transceivers DS51869A-page 26 (c) 2009 Microchip Technology Inc. Installation and Operation FIGURE 2-6: DEMO #2 ALTERNATE POWER CONFIGURATION BOARD EDGE PIC18F65J50 GND VDD Jumper Shunts Removed Da ta ow Fl IR Transceivers (c) 2009 Microchip Technology Inc. DS51869A-page 27 MCP2150 Developer's Board User's Guide TABLE 2-3: Step DEMO #2 STEPS - DATA STREAMING MODE Action Result 1 Place the Primary Device's IR port and the MCP2150 -- Developer's Board on a flat surface about 25 cm (10 inches) apart, and with the IR ports facing each other. 1 On the MCP2150 Developer's Board: Ensure that the jumpers are configured as in Figure 2-5. -- 2 On the MCP2150 Developer's Board: Apply power to the unit via the USB connector. The PIC reset switch (S1) may be depressed and released to ensure that the PIC had a good reset. On the MCP2150 Developer's Board: The green power LED (D1) will turn on. 3 On the PC: Open the HyperTerminal program window for the Primary Device (such as COM 7). Ensure that the window indicates that the HyperTerminal program is connected. On the MCP2150 Developer's Board: -- Note: 4 5 See D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)" On the PC: The system tray Icon will change from a single IR Icon to two IR Icons facing each other. An IR Link is now established. On the PC: In the HyperTerminal program window, type any character. On the MCP2150 Developer's Board: -- On the PC: Disconnect the HyperTerminal program window. On the PC: HyperTerminal program window no longer receives data. DS51869A-page 28 On the PC: Then, a continuous stream of a 250 Byte table will be received from the embedded system in the HyperTerminal window (See for Appendix E. "Continuously Transmitted Data Table") (c) 2009 Microchip Technology Inc. Installation and Operation 2.3.3 Demo #3 Operation - Echo Data Mode In Demo #3, the MCP2150 Developer's Board (MCP2150DM) will communicate via the IR interface to the PC. The MCP2150DM is the Secondary Device, and will echo the received data (after changing the case) to the Primary Device (PC). This shows the command/response of an application system. Figure 2-7 shows the system setup for this test, while Figure 2-8 shows the jumper configuration for the MCP2150 board. Lastly, Table 2-4 shows the steps for Demo #2 operation. DEMO #3 SYSTEM BLOCK DIAGRAM (1) FIGURE 2-7: HyperTerminal Program Window A (to IrDA Dongle) (1) (2) Monitor PC System #1 (1) Serial (UART or USB) to IrDA Dongle Note 1: 2: System #2 MCP2150 Developer's Board The PC may be a Notebook with an Integrated IR port. This operates as the Primary Device. USB cable (for power only). (c) 2009 Microchip Technology Inc. DS51869A-page 29 MCP2150 Developer's Board User's Guide FIGURE 2-8: DEMO #3 CONFIGURATION - ECHO DATA MODE BOARD EDGE PIC18F65J50 Da ta ow Fl IR Transceivers DS51869A-page 30 (c) 2009 Microchip Technology Inc. Installation and Operation TABLE 2-4: DEMO #3 STEPS - ECHO DATA MODE Step Action Result 1 Place the Primary Device's IR port and the MCP2150 Developer's Board on a flat surface about 25 cm (10 inches) apart, and with the IR ports facing each other. -- 2 On the MCP2150 Developer's Board #1: Ensure that the jumpers are configured as in Figure 2-5. Jumpers shown in green are not required and can be left open. -- 3 On the MCP2150 Developer's Boards: Apply power to the unit via the USB connector. On the MCP2150 Developer's Board: The green power LED (D1) will turn on. 4 On the PC: Open the HyperTerminal program window for the Primary Device (such as COM 7). Ensure that the window indicates that the HyperTerminal program is connected. On the MCP2150 Developer's Board: -- Note: See D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)" On the PC: The system tray Icon will change from a single IR Icon to two IR Icons facing each other. An IR Link is now established. 5 On the PC: On the PC: In the HyperTerminal program window, type some alpha The HyperTerminal program window will display characters, such as "kLwtGh". each character and its switched case version. So, "kLwtGh" will show "kKLlwWtTGghH". 6 Continue typing any alpha characters (upper or lower case) The alpha character typed and its opposite case will be displayed (such as "aA", "Aa", "Bb", ...) 7 On the PC: Disconnect the HyperTerminal program window. On the PC: HyperTerminal program window no longer receives data. (c) 2009 Microchip Technology Inc. DS51869A-page 31 MCP2150 Developer's Board User's Guide 2.3.4 Demo #4 Operation - IR / UART (DB-9) Pass Through PIC Mode In Demo #4, the MCP2150 Developer's Board will communicate to the PC (or IrDA to serial interface Dongle) data received on the DB-9 port. This demo shows the MCP2150 converting data between the IR port and the Host UART port. The Primary Device's IR packet is decoded and any data is extracted and transmitted on the Host UART interface. Data received on the Host UART interface is formatted into the IR data packet and transmitted to the Primary device. Figure 2-9 shows the system setup for this test, while Figure 2-10 shows the jumper configuration for the MCP2150 board. Lastly, Table 2-5 shows the steps for Demo #4 operation. DEMO #4 SYSTEM BLOCK DIAGRAM(1) FIGURE 2-9: HyperTerminal Program Window A (to IrDA Dongle) (1) (2) HyperTerminal Program Window B (Com 1) (2) Monitor Com 1 PC System #1 (1) Serial (UART or USB) to IrDA Dongle Note 1: (3) System #2 MCP2150 Developer's Board The PC may be a Notebook with an Integrated IR port. This operates as the Primary Device. 2: Serial cable. Connects Secondary Device to PC. 3: USB cable (for power only). Hyperterminal to Serial Port Settings The com port settings should be configured as: * * * * * DS51869A-page 32 115,200 Baud 8-bits No Parity One Stop Hardware Flow Control (c) 2009 Microchip Technology Inc. Installation and Operation FIGURE 2-10: DEMO #4 CONFIGURATION - PASS THROUGH PIC MODE BOARD EDGE PIC18F65J50 RX1 ta Da TX1 ow RX2 Fl (c) 2009 Microchip Technology Inc. ta DB-9 Connector Da Fl ow TX2 IR Transceivers DS51869A-page 33 MCP2150 Developer's Board User's Guide TABLE 2-5: DEMO #4 STEPS - PASS THROUGH PIC MODE Step Action Result 1 Place the Primary Device's IR port and the MCP2150 Developer's Board on a flat surface about 25 cm (10 inches) apart, and with the IR ports facing each other. -- 2 On the MCP2150 Developer's Board: Ensure that the jumpers are configured as in Figure 2-10. -- 3 On the MCP2150 Developer's Board: On the MCP2150 Developer's Board: Apply power to the unit via the USB connector. The PIC The green power LED (D1) will turn on. reset switch (S1) may be depressed and released to ensure that the PIC had a good reset. 4 Connect PC's Serial Port to the DB-9 connector of the MCP2150 Developer's Board. 5 On the PC: -- Wait for the PC to make a sound and the system tray to show an IR Icon. Placing the mouse over the Icon will show the MCP2150 Device ID (currently "Generic IrDA"). 6 On the PC: Open the HyperTerminal program window for the Primary Device (such as COM 7). Ensure that the window indicates that the HyperTerminal program is connected. Note: 7 See D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)" -- On the MCP2150 Developer's Board: -- On the PC: The system tray Icon will change from a single IR Icon to two IR Icons facing each other. An IR Link is now established. On the PC: -- Open a second instance of HyperTerminal program window attached to the PC's Serial Port (such as COM 2) to connect to the MCP2150 Developer's Board. Ensure that the window indicates that the HyperTerminal program is connected. Note: See D.1.3 "HyperTerminal Configuration for the Secondary Device" 8 On the PC: In one of the HyperTerminal program windows (such as the Primary Device's window), type some characters. On the PC: In the other HyperTerminal program windows (the Serial Port window), those characters appear. 9 On the PC: In the other HyperTerminal program windows (Serial Port window), type some characters. On the PC: In the other HyperTerminal program windows (the Primary Device's window), those characters appear. 10 On the PC: In either HyperTerminal program windows, select the Transfer pull-down menu and then the Send Text File ... option. Navigate to the folder that contains the Transmit File.Txt file and select it. Then click Open. On the PC: In the selected HyperTerminal program window the displayed data is transmitted and is received and displayed by the other HyperTerminal program window. 11 On the PC: Make this file transfer transmitting from the other HyperTerminal program window. On the PC: In the selected HyperTerminal program window, the displayed data is transmitted, being received and displayed by the other HyperTerminal program window. 12 Continue steps 8, 9 10, or 11 for as long as desired. -- DS51869A-page 34 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix A. Schematic and Layouts NOTICE TO CUSTOMERS All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some schematics and board layouts may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available. A.1 INTRODUCTION This appendix contains the following schematics and layouts for the MCP2150 Developer's Board: * * * * * * * Board - Schematic Board - Top Silk and Pads Board - Top Layer Board - Top Silk and Pads Top layer Board - Bottom Layer Board - VDD Layer Board - Ground Layer The layer order is shown in Figure A-1. FIGURE A-1: LAYER ORDER Top Layer Ground Layer Power Layer Bottom Layer (c) 2009 Microchip Technology Inc. DS51869A-page 35 TX RX RI DSR DTR CTS RTS CD DS51869A-page 36 TX RX RI DSR DTR CTS RTS CD 5 VSS 7 8 9 10 11 12 13 17 OSC2 OSC1/CLKI RXIR TXIR EN BAUD1 BAUD0 RESET 15 16 3 2 6 18 1 4 VDD 14 15 16 3 2 6 18 1 4 VDD 14 OSC2 OSC1/CLKI RXIR TXIR EN BAUD1 BAUD0 RESET M A.2 5 VSS 7 8 9 10 11 12 13 17 MCP2150 Developer's Board User's Guide BOARD - SCHEMATIC - PAGE 1 (c) 2009 Microchip Technology Inc. Schematic and Layouts BOARD - SCHEMATIC - PAGE 2 M A.3 (c) 2009 Microchip Technology Inc. DS51869A-page 37 MCP2150 Developer's Board User's Guide A.4 BOARD - TOP SILK AND PADS BOARD EDGE DS51869A-page 38 (c) 2009 Microchip Technology Inc. Schematic and Layouts A.5 BOARD - TOP LAYER (c) 2009 Microchip Technology Inc. DS51869A-page 39 MCP2150 Developer's Board User's Guide A.6 BOARD - TOP LAYER WITH SILK AND PADS BOARD EDGE DS51869A-page 40 (c) 2009 Microchip Technology Inc. Schematic and Layouts A.7 BOARD - BOTTOM LAYER (c) 2009 Microchip Technology Inc. DS51869A-page 41 MCP2150 Developer's Board User's Guide A.8 BOARD - POWER LAYER DS51869A-page 42 (c) 2009 Microchip Technology Inc. Schematic and Layouts A.9 BOARD - GROUND LAYER (c) 2009 Microchip Technology Inc. DS51869A-page 43 MCP2150 Developer's Board User's Guide NOTES: DS51869A-page 44 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix B. Bill Of Materials (BOM) NOTICE TO CUSTOMERS All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so the Bill Of Materials may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available. The MCP2150 Developer's Board allows the MCP2150 device to be evaluated. The board supports customers in the evaluation of three additional optical transceiver devices. This is done with component layout of these additional optical transceiver circuits. The customer would be required to install the desired circuit for testing. Table B-1 shows the components that are installed in the MCP2150 Developer's Board PCB, while Table B-2 shows the components that are NOT installed on the MCP2150 Developer's Board PCB. TABLE B-1: Qty 2 BILL OF MATERIALS (BOM) Reference C1,C2 Description CAP 1.0UF 16V CERAMIC X7R 0805 Manufacturer Kemet Panasonic(R) Part Number C0805C105K4RACTU 9 C3, C7, C11, CAP .1UF 25V CERAMIC X7R 0805 C13, C16, C17, C18, C19, C20 2 C21, C23 CAP .1UF 25V CERAMIC X7R 0603 Panasonic - ECG ECJ-1VB1E104K 4 C8, C9 CAP CERAMIC 22PF 50V NP0 0805 Kemet(R) Electronics Corp. C0805C220J5GACTU 2 C10, C12 CAPACITOR 4.7UF/10V TEH SER SMD Panasonic - ECG ECS-H1AX475R 1 C22 CAP 4.7UF 10V X53 0603 Panasonic - ECG C0603C475K8PACTU 2 D1, D2 LED GREEN CLEAR 0805 SMD LITE-ON(R) Semiconductor Corp. LTST-C170CKT 1 HD1 CONN HEADER.100 SINGL STR 12POS Sullins Connector Solutions PEC12SAAN 1 J1 CONN RECEPT MINI USB2.0 5POS Hirose Electronic Co. Ltd UX60-MB-5ST 1 J2 CONN HEADER.100 SINGL STR 6POS (Note 2) Sullins Connector Solutions PEC06SAAN 1 J3 CONN D-SUB RCPT R/A 9POS PCB AU Amphenol 6E17C-009S-AJ-120 Commercial Products - ECG ECJ-2VB1E104K Note 1: The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components. 2: This connector can be made by cutting a single .100 Single R/A 36POS into six pieces. (c) 2009 Microchip Technology Inc. DS51869A-page 45 MCP2150 Developer's Board User's Guide TABLE B-1: Qty BILL OF MATERIALS (BOM) (CONTINUED) Reference Description Manufacturer (R) Part Number (R) 14 JMP1, JMP2, CONN HEADER 3POS .100" STR TIN JMP3, JMP4, JMP5, JMP6, JMP7, JMP8, JMP9, JMP10, JMP11, JMP12, JMP13, JMP14 Molex /Waldom Electronics Corp 90120-0123 1 JMP6 CONN HEADER 16POS .100 VERT GOLD Molex/Waldom Electronics Corp. 10-89-1161 5 JP1, JP2, JP3 JP1C, JP2C CONN HEADER 2POS .100 VERT TIN Molex/Waldom Electronics Corp 22-03-2021 1 L1 INDUCTOR POWER 10UH 1008 TDK(R) Corporation NLV25T-100J-PF 1 PCB RoHS Compliant Bare PCB, MCP2150 Developer's Board Microchip Technology 104-00265 Inc. 1 Q1 300mA CMOS LDO Microchip Technology TC1108-3.3VDB Inc. 9 R2, R12, R13, RES 10K OHM 1/8W 5% 0805 SMD R14, R15, R16, R17, R18, R19 Panasonic - ECG ERJ-6GEYJ103V 4 R20, R21, R22, RES 10K OHM 1/10W 5% 0603 SMD R23 Panasonic - ECG ERJ-3GEYJ103V 1 R6 RES 0.0 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEY0R00V 1 R8 RES 47 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEYJ470V 2 R10, R11 RES 470 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEYJ471V 1 R25 RES 100 OHM 1/10W 5% 0603 SMD Panasonic - ECG ERJ-3GEYJ101V 4 R26, R27, R28,R29 RES 10K OHM 1/10W 5% 0603 SMD Panasonic - ECG ERJ-3GEYJ102V 1 S1 SWITCH LT TOUCH 6X3.5 100GF SMD Panasonic - ECG EVQ-PE104K 1 U2 64/80-Pin High-Performance, 1-Mbit Flash Microchip Technology PIC18F86J50-I/PT USB Microcontrollers Inc. 1 U5 Intelligent +3.0V to +5.5V RS-232 Transceiver SIPEX 1 U6 MCP111 Micropower Voltage Detector Microchip Technology MCP111-315E/TT Inc. 1 U11 MCP2150 SOIC-18 IrDA(R) Standard Protocol Stack Controller Microchip Technology MCP2150T-I/SO Inc. 1 U4 Infrared Transceivers SIR 115.2 kbits/s Vishay(R) Semiconductor TFDU4300-TR3 2 VDD, GND TEST POINT PC COMPACT SMT Keystone(R) Electronics 5016 1 Y1 CRYSTAL 14.7456 MHZ 20PF SMD CTS-Frequency Controls ECS-147.4-20-5P-TR 2 Y2 PIN RECPT .015/.025 DIA 0667 SER Mill-Max Manufacturing 0667-0-15-01-30-27-10-0 4 Bottom side on Each Corner BUMPON HEMISPHERE .44X.20 BLACK 3M SJ-5003 (BLACK) 17 Shunts for JP2, JP1C, JP2C, JMP1-JMP14 .100" Shorting Block with Handle JAMECO(R) VALUEPRO 2012JH-R SP3238EEY-L Note 1: The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components. 2: This connector can be made by cutting a single .100 Single R/A 36POS into six pieces. DS51869A-page 46 (c) 2009 Microchip Technology Inc. Bill Of Materials (BOM) TABLE B-2: Qty 0 0 TABLE OF CONTENTS (BOM) - PCB COMPONENTS NOT INSTALLED Reference C4 C5 Description Manufacturer Part Number CAP .47UF 16V CERAMIC X7R 080 Panasonic - ECG ECJ-2YB1C474K AP TANTALUM 6.8UF 16V 20% SMD Nichicon(R) F931C685MAA Corporation 0 C6 CAP 4.7UF 16V CERAMIC F 0805 Panasonic - ECG ECJ-2FF1C475Z 0 C7 CAP .1UF 25V CERAMIC X7R 0805 Panasonic - ECG ECJ-2VB1C104K 0 JP1A, JP1B, JP2A, JP2B CONN HEADER 2POS .100 VERT TIN Molex/Waldom Electronics Corp. 22-03-2021 0 R1 RES 2.2 OHM 1/8W 1% 0805 SMD Panasonic - ECG ERJ-6RQF2R2V 0 R3, R4, R5 RES 0.0 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEY0R00V 0 U1 IRDA MODULE 115.2KBPS 6-SMD LITE-ON Semiconductor Corp. HSDL-3000#007 0 U3 Infrared Transceivers SIR 115.2 kbits/s Vishay(R) TFDU4101-TR3 0 U9 IC SOCKET 18PIN MS TIN/TIN .300 Mill-Max Manufacturing Corp. 110-99-318-41-001000 Note 1: The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components. (c) 2009 Microchip Technology Inc. DS51869A-page 47 MCP2150 Developer's Board User's Guide NOTES: DS51869A-page 48 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix C. Board Testing The MCP2150 Developer's Board can be used in multiple configurations. Only a subset of these configurations were tested. TABLE C-1: MCP2150 DEVELOPER'S BOARD TESTED CONFIGURATIONS - DEMO # 1 MCP2150 UART Input Signals Program Power Select JP2 JMP1: JMP7 JMP8: JMP14 JMP16 Short 1-2 Short 2-3 All Open BAUD JP1: JP3 S IrDA Signals RXIR TXIR Comment JP1C JP2C O:O S S Data Pass Through Mode (IR to DB-9). Legend: O = Jumper is "Open" S = Jumper is "Shorted" 1-2 = Pin 1 is shorted to Pin 2 (of 3 pin header) 2-3 = Pin 2 is shorted to Pin 3 (of 3 pin header) TABLE C-2: MCP2150 DEVELOPER'S BOARD TESTED CONFIGURATIONS - DEMO # 4 MCP2150 UART Input Signals JMP1: JMP7 JMP8: JMP14 Short 2-3 Short 1-2 Program Select JMP16 Short RD6, All others Open Power JP2 BAUD JP1: JP3 S O:O IrDA Signals RXIR TXIR Comment JP1C JP2C S S Data Pass Through Mode (IR to PIC to DB-9). Legend: O = Jumper is "Open" S = Jumper is "Shorted" 1-2 = Pin 1 is shorted to Pin 2 (of 3 pin header) 2-3 = Pin 2 is shorted to Pin 3 (of 3 pin header) C.1 WHAT IS TESTED The following portions of the board are tested: * * * * * * * * * * * MCP2150 IrDA Standard Protocol Handler PIC18F65J50 microcontroller TFDU-4300 (U4) and circuitry (JP1C, JP2C) USB Power circuitry DB-9 Interface and circuitry MAX3238 compatible device) ICSP Header (J2) PIC microcontroller (PIC18F65J50) PIC16F65J50 crystal circuitry (14.7456 MHz) MCP2150 crystal circuitry (11. 0952 MHz) JMP1 - JMP14 (P1 - P2, P2 - P3) RD6 jumper (c) 2009 Microchip Technology Inc. DS51869A-page 49 MCP2150 Developer's Board User's Guide C.2 WHAT IS NOT TESTED The following portions of the board are NOT tested: * * * * * * * * DS51869A-page 50 TFDU-4101 (U3) and circuitry HSDL-3000 (U1) and circuitry Header HD1 JP1, JP2, JP3 PortD jumpers (except RD6) - on jumper JMP16 JP1A, JP2A, JP1B, JP2B USB Data Lines Switch S1 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix D. Configuring the HyperTerminal(R) Program D.1 CONFIGURING THE HyperTerminal(R) PROGRAM In running a demo, one may need two instances of the HyperTerminal program in operation. The instance for the Primary Device will always be used, while the instance for the Secondary Device will only be used for Test #1 and Test #4. The configuration of HyperTerminal is different between these two instances. D.1.1 HyperTerminal Configuration for the Primary Device This configuration connects the HyperTerminal window to the PC's IrDA Port (via a virtual Serial Port, for example COM 7), which then can communicate to the Secondary Device (via the MCP2150 Developer's Board IrDA interface). To use a Laptop PC with an IrDA standard port as the Primary device, the application program must connect to the IR port. Some standard Windows programs may not be able to connect directly to the IR port (OS specific). For a Windows(R) XP (or Windows 2000) system, a 3rd-party driver needs to be installed to "create" the "virtual port" that HyperTerminal needs to connect so that it allows to use the IR port for communications. This driver is called IrCOMM2K and is available at www.IRCOMM2K.de. Please evaluate this product before installing onto your system to ensure that it will meet your requirements. Microchip does not imply any suitability to your system requirements of any of these 3rd-party products. Please evaluate each product's specifications and requirements before installing onto your system. Once the IrCOMM2K driver is installed, it creates a "new" com port (such as COM7). This is a virtual serial port that the PC Terminal Emulation application program (such as HyperTerminal) can be connected to. To ensure that the PC is able to communicate to the PICDEMTM HPC Explorer Demo Board plus MCP2150 Developer's Board, the HyperTerminal program must be properly configured. This section describes the configuration that the HyperTerminal program should be in. Then, HyperTerminal needs to be configured. Refer to Section D.1.2 "Configuring HyperTerminal to connect to the IrDA Port (Virtual Port)". (c) 2009 Microchip Technology Inc. DS51869A-page 51 MCP2150 Developer's Board User's Guide D.1.2 Configuring HyperTerminal to connect to the IrDA Port (Virtual Port) 1. Start the HyperTerminal Emulation program (usually located under the Programs>Accessories>Communications directory). FIGURE D-1: CONNECTION DESCRIPTION WINDOW 2. In the Connection Description window, select the Cancel button. Then, the window in Figure D-2 will be the focus window. FIGURE D-2: DS51869A-page 52 HyperTerminal PROGRAM MAIN WINDOW (c) 2009 Microchip Technology Inc. Configuring the HyperTerminal(R) Program 3. If the HyperTerminal program window does not indicate that the window is "Disconnected", select Call>Disconnect. In the lower-left corner, the HyperTerminal program window will indicate "Disconnected". 4. In the program menu, select File>Properties. The window in Figure D-3 is shown. FIGURE D-3: NEW CONNECTION PROPERTIES WINDOW 5. In the New Connection Properties window, on the Connect To tab, go to the "Connect Using" pull-down and select the desired COM port. For the Primary Device, this will be the virtual serial port created by the IrCOMM2K driver installation (such as COM7). For the connection to the Embedded System, this will be one of the standard COM ports (such as COM1, COM2, or COM3). (c) 2009 Microchip Technology Inc. DS51869A-page 53 MCP2150 Developer's Board User's Guide 6. Select the Configure button. This will open up the Port Settings window (Figure D-4). FIGURE D-4: HyperTerminal PROGRAM PROPERTIES CONFIGURATION WINDOW Primary Device Flow Control Secondary Device Flow Control 7. In the COMx (COM7) Properties window, configure the Port Setting for: - "Bits per second:" = 115200 - "Data Bits:" = 8 - "Parity:" = None - "Stop Bit:" = 1 - "Flow Control:" = None (for Primary Device) or "Flow Control:" = Hardware (for Secondary Device) The port settings would then be configured as shown in Figure D-4. 8. Select the OK button. The Figure D-3 window will be shown. 9. In the New Connection Properties window, select the Settings tab. The window will now look as shown in Figure D-5. Ensure that your settings match the settings shown. 10. Configure the New Connection Properties Settings. - Under the "Function, arrow and control keys act as" item, select the Terminal Keys radio button. - Under the "Backspace key sends" item, select the Ctrl+H radio button. - From the "Emulation" pull-down menu, select Auto-detect. - For "Telnet Terminal ID", enter ANSI. - For "Backscroll buffer lines", select 500 from the pull-down menu. 11. Press the ASCII Setup button. This will open the ASCII Setup window (Figure D-5). DS51869A-page 54 (c) 2009 Microchip Technology Inc. Configuring the HyperTerminal(R) Program 12. In the ASCII Sending area of the window: - Check "Send Line ends with line feeds". - Check "Echo typed characters locally". - Set the "Line Delay" and the "Character Delay" to `0' milliseconds. 13. In the ASCII Receiving area of the window: - Uncheck "Append line feeds to incoming line ends". - Uncheck "Force incoming data to 7-bit ASCII". - Check "Wrap lines that exceed terminal width". 14. Ensure that your settings match the settings shown. 15. Select the OK button. This closes the ASCII Setup window and returns focus to the New Connection Properties window. FIGURE D-5: NEW CONNECTION PROPERTIES - ASCII SETUP (c) 2009 Microchip Technology Inc. DS51869A-page 55 MCP2150 Developer's Board User's Guide 16. In the New Connection Properties window, select the Input Translation button. This will open the Host System Encoding Method window (Figure D-6). - In the "Host System Encoding Method" window, select Shift-JIS and click the OK button to close the window. 17. Then, click the OK button in the New Connection Properties window. 18. Now that all the settings are configured, in HyperTerminal's pull-down menu, select File>Save As. Select the name that you wish. You may wish to save each configuration with a name that you can remember (one for the Primary Device and the other for the Secondary Device). FIGURE D-6: DS51869A-page 56 NEW CONNECTION PROPERTIES - HOST SYSTEM ENCODING METHOD (c) 2009 Microchip Technology Inc. Configuring the HyperTerminal(R) Program D.1.3 HyperTerminal Configuration for the Secondary Device This configuration connects the HyperTerminal window to the selected PC's Serial Port (for example COM 2), which then can communicate to the Embedded System (via the MCP2150 Developer's Board DB-9 interface). Figure D-7 through Figure D-10 show the HyperTerminal configuration for the PC Serial Port connection to the MCP2150's DB-9 inteface. Figure D-7 shows the selected COM port to connect to and the configuration of that COM port (9600 baud, 8-bits, 1 stop bit, no parity, with hardware flow control). The COM port for your system may need to be different. 1. Clicking on the Settings tab displays the window shown in Figure D-8. FIGURE D-7: NEW CONNECTION PROPERTIES - PORT CONFIGURATION (c) 2009 Microchip Technology Inc. DS51869A-page 57 MCP2150 Developer's Board User's Guide FIGURE D-8: DS51869A-page 58 NEW CONNECTION PROPERTIES - PORT SETTINGS (c) 2009 Microchip Technology Inc. Configuring the HyperTerminal(R) Program 2. Clicking on the Input Translation button displays the window shown in Figure D-9, while clicking on the ASCII Setup button displays the window shown in Figure D-10. FIGURE D-9: NEW CONNECTION PROPERTIES - INPUT TRANSLATION (c) 2009 Microchip Technology Inc. DS51869A-page 59 MCP2150 Developer's Board User's Guide FIGURE D-10: DS51869A-page 60 NEW CONNECTION PROPERTIES - ASCII SETUP (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix E. Continuously Transmitted Data Table E.1 DATA TABLE FOR DEMO #2 Figure E-1 shows the data table that is streamed to the Primary Device after a data byte has been received. After the 250 bytes have been transmitted, the program returns to the top of the table. This table is streamed continuously until the IR link is closed. FIGURE E-1: "12345678", "2BCDEFGH", "32345678", "4bcdefgh", "52345678", "6BCDEFGH", "72345678", "8bcdefgh", "92345678", "ABCDEFGH", "B2345678", "Cbcdefgh", "D2345678", "EBCDEFGH", "F2345678", "1bcdefgh", "22345678", "3BCDEFGH", "42345678", "5bcdefgh", "62345678", "7BCDEFGH", "82345678", "9bcdefgh", "a2345678", NOTE: CONTINUOUSLY TRANSMITTED DATA TABLE 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0D, 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A 0x0A ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters Characters - 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 0x0D = Carriage Return, 0x0A = Line Feed (c) 2009 Microchip Technology Inc. DS51869A-page 61 MCP2150 Developer's Board User's Guide NOTES: DS51869A-page 62 (c) 2009 Microchip Technology Inc. MCP2150 DEVELOPER'S BOARD USER'S GUIDE Appendix F. Programming the MCP2150DM Note: The MCP2150DM is shipped with the default demonstration firmware programmed into the PIC18F65J50. The user may reprogram the PIC18F65J50 with their application firmware or the supplied demo firmware. The Programming will require the following items * * * * 1 PC USB port for programming 1 MPLAB ICD 2 module (with USB cable) 1 RJ-11 to ICSP Adapter (AC164110) CD with .HEX file to program into device (00265.HEX) Figure F-1 shows a high level block diagram for programming the MCP2150 Developer's Board. How to program is described in the appropriate MPLAB-IDE and MPLAB-ICD2 documentation. FIGURE F-1: PROGRAMMING BLOCK DIAGRAM MPLAB Program Window RJ-11 to ICSP Cable ICD 2 PC Monitor USB Cable 1 1 MCP2150 Developer's Board Side View SYSTEM HARDWARE REQUIREMENTS Qty Hardware Purpose 1 PC with one USB port To run MPLAB-IDE and communicate to the ICD or ICE hardware. 1 ICD2, ICD3, or Real ICE To program the MCP2150 Developer's Board PIC18F65J50 device. 1 RJ-11 to ICSP Adapter (AC164110) Converts RJ-11 connector of ICD 2 to pins to use for programming the PICkit interface on the MCP2150 Developer's Board. -- MCP2150 Developer's Board The board to program. (c) 2009 Microchip Technology Inc. DS51869A-page 63 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS51869A-page 64 (c) 2009 Microchip Technology Inc.