PRELIMINARY
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice
1 of 10
www.qorvo.com
8 Pad 1.8 mm x 1.4 mm x 0.73 mm SMT Package
Product Overview
The QPQ1030 is a compact, high-performance duplexe
r
module designed to provide the low insertion loss and
high OOB attenuation required for true co-banding.
The QPQ1030 is manufactured using Qorvo’s high
performance NoDrift™ Bulk Acoustic Wave (BAW)
technology yielding a duplexer that satisfies stringent OOB
attenuation requirements over temperature extremes.
The QPQ1030 uses Qorvo’s unique Wafer-Level-
Packaging (WLP) techniques to achieve a compact
1.8 mm x 1.4 mm x 0.73 mm package that is lead free and
RoHS complaint.
The QPQ1030 is part of Qorvo’s extensive portfolio of RF
BAW and SAW filters
Key Features
Compact Form-Factor: 1.8 x 1.4 mm
Insertion Loss – Enabling True Co-Banding
- Tx Band, 2305 – 2318 MHz: 1.7dB Typ.
- Rx Band, 2347 – 2360 MHz: 1.9dB Typ.
Best In Class Close OOB Attenuation Over Temperature
High ISM Band Rejection
Single-Ended (SE) 50 Ohm Receive & Transmit Ports
RoHS Compliant, Pb-Free
Applications
UE Terminals
Smart Grid
IoT applications
Functional Block Diagram
Top View
Pin Configuration
Pin # Label
1 Receive
3 Transmit
6 Antenna
2, 4, 5, 7, 8 GND
Backside Center Pad 2 GND
*See application section for details on optimal grounding.
Ordering Information
Part No. Description
QPQ1030 2500 pieces on a 7” reel (standard)
QPQ1030-EVB Evaluation Board
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 2 of 10 www.qorvo.com
Absolute Maximum Ratings
Parameter Rating
Storage Temperature −40 to +85 °C
RF Input Power (CW, 50 Ω,Temp. = 25 °C) TBD dBm
RF Input Power (Instantaneous) TBD dBm
Exceeding any one or a combination of the Absolute Maximum
Rating conditions may cause permanent damage to the device.
Extended application of Absolute Maximum Rating conditions to
the device may reduce device reliability.
Life Test
Conditions Rating
+29 dBm, +50 °C, CW power applied to pin 1 TBD Hrs
Recommended Operating Conditions
Parameter Min Typ. Max Units
TCASE −20 +90 °C
The duplexer will function over the recommended range without
degradation in reliability or permanent change in performance.
Electrical Specifications – Antenna to Transmit
Parameter Conditions (1,2) Min Typ (3) Max Units
Insertion Loss 2305 – 2318 MHz - 1.7 3.6 dB
Amplitude Ripple 2305 – 2318 MHz - 0.2 1.8 dB
Group Delay 2300 – 2318 MHz - 31 40 ns
VSWR (in/out) 2305 – 2318 MHz - 1.3:1 2:1 -
ANT Impedance - 50||5.1nH(5) - Ohms
TX Impedance - 50 - Ohms
Attenuation (4)
1225 – 1250 MHz 40 44 -
dB
1559 – 1563 MHz 40 44 -
1565.42 – 1573.374 MHz 40 44 -
1573.3 – 1577.466 MHz 40 44 -
1577.466 – 1585.42 MHz 40 44 -
1597.5515 – 1605.886 MHz 40 44 -
2200 – 2288 MHz 10(6) 18 -
2288 – 2292 MHz 713 -
2292 – 2296 MHz 38 -
2320 – 2324 MHz 2 3 -
2324 – 2328 MHz 3 7 -
2328 – 2332 MHz 6.5 10 -
2332 – 2350 MHz 10(6) 19 -
2347 – 2360 MHz 46 53 -
2400 – 2485 MHz 40 48 -
4610 – 4630 MHz 35 40 -
4900 – 5950 MHz 20 24 -
6915 – 6945 MHz 30 35 -
Notes:
1. Temperature Range for specified performance: −20 °C to +90 °C.
2. All specifications are based on the Qorvo schematic for the main reference design.
3. Typical values are an average of 20 pieces measured at a temperature of 25 °C.
4. Attenuation is referenced to ZER0 dB.
5. Matching value based on simulation results
6. Relative rejection to max insertion loss.
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 3 of 10 www.qorvo.com
Electrical Specifications – Receive Port
Parameter Conditions (1,2) Min Typ (3) Max Units
Insertion Loss 2347–2360 MHz - 1.9 3.8 dB
Amplitude Ripple 2347–2360 MHz - 0.2 1.9
Group Delay 2350–2360 MHz - 34 40 ns
VSWR (in/out) 2350–2360 MHz - 1.3:1 2:1 -
ANT Impedance - 50//5.1nH(5) - Ohms
RX Impedance - 50 - Ohms
Attenuation
699–716 MHz 40 45 -
dB
824–849 MHz 40 45 -
1710–1755 MHz 35 40 -
1850–1910 MHz 35 41 -
2305–2318 MHz 49 57 -
2327–2337 MHz 10 18 -
2336.2–2341.3 MHz 3 7 -
2400–6000 MHz 32 40 -
2400–2500 MHz 40 45 -
4900 – 5950 MHz 30 35 -
Notes:
1. Temperature Range for specified performance: −20 °C to +90 °C.
2. All specifications are based on the Qorvo schematic for the main reference design.
3. Typical values are an average of 20 pieces measured at a temperature of 25 °C.
4. Attenuation is referenced to ZER0 dB.
5. Matching value based on simulation results
Electrical Specifications – Transmit to Receive
Parameter Conditions (1,2) Min Typ (3) Max Units
Isolation
2305–2318 MHz 51 58 - dB
2347–2360 MHz 49 57 - dB
1574–1577 MHz 50 54 - dB
Notes:
1. Temperature Range for specified performance: −20 °C to +90 °C.
2. All specifications are based on the Qorvo schematic for the main reference design.
3. Typical values are an average of 20 pieces measured at a temperature of 25 °C.
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 4 of 10 www.qorvo.com
Transmit Performance Plots – Temp.=+25 C
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 5 of 10 www.qorvo.com
Receive Performance Plots – Temp.=+25 C
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 6 of 10 www.qorvo.com
Isolation Plots – Temp.=+25 C
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 7 of 10 www.qorvo.com
Schematic
3
1
6
2,4,5,7,8
ANT
Rx
Tx
5.1nH
Bill of Materials − EVB
Reference Des. Value Description Manuf. Part Number
U1 N/A WCS-Extended BAW Duplexer Qorvo QPQ1030
L1 5.1 nH Shunt Inductor at ANT pin 6 Murata LQP03TN5N1H02
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice
8 of 10
www.qorvo.com
Package Marking and Dimensions
Marking: Trace Code – XXXX
NOTES:
1. All dimensions are in millimeters. Angles are in degrees.
2. Except where noted, this part outline conforms to JEDEC standard MO-220, Issue E (Variation VGGC) for thermally enhanced
plastic very thin fine pitch quad flat no lead package (QFN).
3. Dimension and tolerance formats conform to ASME Y14.4M-1994.
XXXX
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice 9 of 10 www.qorvo.com
Tape and Reel Information
Standard T/R size = 2,500 units/reel. All dimensions are in millimeters
CAVITY (mm) DISTANCE BETWEEN
CENTERLINE (mm)
CARRIER
TAPE (mm)
COVER
TAPE (mm)
Length
(A0)
±0.05
Width
(B0)
±0.05
Depth
(K0)
±0.05
Pitch
(P1)
Length
direction
(P2)
Width
Direction
(F)
Width
(W)
Width
(W)
1.60 2.0 0.95 4.0 2.00 3.50 8.0 5.4
PRELIMINAR
Y
QPQ1030
WCS-Extended BAW Duplexer
Data Sheet Aug. 5, 2016 | Subject to change without notice
10 of 10
www.qorvo.com
Handling Precautions
Parameter Rating Standard
Caution!
ESD-Sensitive Device
ESD – Human Body Model (HBM) Class 1B ESDA / JEDEC JS-001-2012
ESD – Charged Device Model (CDM) Class C3 JEDEC JESD22-C101F
MSL – Moisture Sensitivity Level Level 3 IPC/JEDEC J-STD-020
Solderability
Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes.
Solder profiles available upon request.
Contact plating: Electrolytic Ni/Au
RoHS Compliance
This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU.
This product also has the following attributes:
Lead Free
Halogen Free (Chlorine, Bromine)
Antimony Free
TBBP-A (C
15
H
12
Br
4
0
2
) Free
PFOS Free
SVHC Free
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders fo
r
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS
DESCRIBED HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS
WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR
OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in
medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe
personal injury or death.
Copyright 2016 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
