TPS92560MR16BSTEVM - Texas Instruments

User's Guide

SLVU822–December 2012

User's Guide for TPS92560MR16BSTEVM

This user’s guide describes the characteristics, operation and use of the TPS92560MR16BSTEVM

evaluation module. This EVM contains Texas Instruments' TPS92560 configured as a boost LED driver

solution for MR16 applications. This EVM can deliver up to 12-W output power with a typical 12-VAC

(50Hz/60Hz) power source. The EVM is ideal for typical MR16 or AR111 applications that require high

compatibility to different power sources. This user's guide includes EVM specifications, recommended test

setup, test results, bill of materials, and a schematic diagram.

Contents

1 Applications .................................................................................................................. 2

2 TPS92560MR16BSTEVM Electrical Performance Specifications .................................................... 2

3 Schematic and Bill of Materials ........................................................................................... 3

4 Connector Descriptions .................................................................................................... 4

4.1 Output Connections ................................................................................................ 4

4.2 Input Connections .................................................................................................. 5

5 PCB Cutouts ................................................................................................................. 5

6 Test Requirements and Setup ............................................................................................ 6

6.1 Hardware Requirements .......................................................................................... 6

6.2 Hardware Setup .................................................................................................... 6

6.3 Typical Waveforms ................................................................................................ 7

7 TPS92560MR16BSTEVM Assembly Drawings and Layout ........................................................... 9

List of Figures

1 TPS92560MR16BSTEVM Schematic.................................................................................... 3

2 TPS92560MR16BSTEVM Input and Output Terminals................................................................ 4

3 Removing Outer Frame of the TPS92560MR16BSTEVM............................................................. 5

4 Connection Diagram of the TPS92560MR16BSTEVM ................................................................ 6

5 Waveforms of Powering the TPS92560MR16BSTEVM with an Electronic Transformer.......................... 7

6 Waveforms of Powering the TPS92560MR16BSTEVM with 12 VAC at 50 Hz ...................................... 8

7 Waveforms of Powering the TPS92560MR16BSTEVM with 12 VDC ................................................ 8

8 TPS92560MR16BSTEVM Top View ..................................................................................... 9

9 TPS92560MR16BSTEVM Bottom View ................................................................................. 9

List of Tables

1 TPS92560MR16BSTEVM Electrical Performance Specifications.................................................... 2

2 Bill of Materials ............................................................................................................. 4

3 Hardware Requirements ................................................................................................... 6

SLVU822–December 2012 User's Guide for TPS92560MR16BSTEVM

Applications

www.ti.com

1 Applications

5- to 10-W MR16 or AR111 LED lamps

2 TPS92560MR16BSTEVM Electrical Performance Specifications

Table 1 provides a summary of the electrical performance specifications of the EVM. All specifications are

given for an ambient temperature of 25°C.

Table 1. TPS92560MR16BSTEVM Electrical Performance Specifications

Parameter Notes and Conditions Min Typ Max Unit

Input Characteristics

VIN-DC DC input voltage After proper system startup 3 18 V

VIN-AC AC input voltage (50Hz / 60Hz) After proper system startup 6 14 V

Generic Electronic transformer RMS AC voltage 12 V

VIN-ELEC-XFR for MR16/AR111 applications

IIN Input current Regulated input current 500 mA

Output Characteristics

nLED Number of LED LEDs connect in series as a load 6 pieces

VLED LED forward voltage Total forward voltage of the LED string 20 V

Systems Characteristics

fSW Switching frequency Typical switching frequency at VIN = 12 VDC 1.6 MHz

2User's Guide for TPS92560MR16BSTEVM SLVU822–December 2012

Submit Documentation Feedback

GATE

SRC

VCC

SEN

GND

AC1

PGND

AC2

ADJ

TPS92560

R3 C4

D2 D3

To Power

Source

D4 D5

N/A N/A

CMSH3-40MA CMSH3-40MA

CMSH3-40MA

CDRH5D28NP-150NC

15µH

SI2328DS

1µF

0.33Ω 47nF

1µF

330µF

25V

392kΩ

3.92kΩ 1µF

AC1

AC2

To LED

LED+

LED-

575-8

www.ti.com

Schematic and Bill of Materials

3 Schematic and Bill of Materials

Figure 1. TPS92560MR16BSTEVM Schematic

SLVU822–December 2012 User's Guide for TPS92560MR16BSTEVM

Connector Descriptions

www.ti.com

Table 2. Bill of Materials

Designator Value Description Size Part Number MFR

Simple LED Driver for MR16 and AR111 10L mini SOIC Texas

U1 TPS92560 TPS92560

Applications w/exp. pad Instruments

C1 4.7μF Capacitor, Ceramic, 4.7μF, 25V, +/-10%, X5R 0805 GRM21BR61E475KA12L MuRata

C2 1μF Capacitor, Ceramic, 1μF, 50V, +/-10%, X7R 0805 GRM21BR71H105KA12L MuRata

C3, C4 1μF Capacitor, Ceramic, 1μF, 16V, +/-10%, X7R 0603 GRM188R71C105KA12D MuRata

C6 0.047μF Capacitor, Ceramic, 0.047μF, 50V, +/-10%, X7R 0603 GRM188R71H473KA61D MuRata

11.5mm x 8mm

C7 330μF Capacitor, AL, 330μF, 25V, +/-20%, TH ECA-1EHG331 Panasonic

dia.

D1,D2,D3 40V, 3A Diode, Schottky SMA CMSH3-40MA Central Semi.

L1 15μH Inductor, Shielded Drum Core, Ferrite, SMD 6 x 6 x 3mm CDRH5D28NP-150NC Sumida

Q1 100V, 1.15A MOSFET, N-CH, 100V, 1.15A SOT23 SI2328DS Vishay Siliconix

R1 105ΩResistor, 105Ω, 1%, 0.125W 0805 CRCW0805105RFKEA Vishay-Dale

R2 392kΩResistor, 392kΩ, 1%, 0.1W 0603 RC0603FR-07392KL Yageo America

R3 3.92kΩResistor, 3.92kΩ, 1%, 0.1W 0603 RC0603FR-073K92L Yageo America

R4 0.33ΩResistor, 0.33Ω, 1%, 0.125W 0805 ERJ-6RQFR33V Panasonic

C5 No connection 0603

D4, D5 No connection SMA

J1, J2, J3, J4 Jumper Wire, 300mil spacing, Orange 300mil spacing 923345-03-C 3M

AC1, AC2, Standard Banana Jack 8.9mm dia. 575-8 Keystone

LED+, LED–

H5, H6, H7, H8 Nylon Standoff Hex, 0.5"L 1902C Keystone

B&F Fastener

H1, H2, H3, H4 Nylon Screw M3 NY PMS 440 0025 PH Supply

4 Connector Descriptions

Figure 2 shows the input and output connectors for this EVM.

Figure 2. TPS92560MR16BSTEVM Input and Output Terminals

4.1 Output Connections

The output terminals of the EVM are described in Section 4.1.1 and Section 4.1.2.

4User's Guide for TPS92560MR16BSTEVM SLVU822–December 2012

Submit Documentation Feedback

CUT

Bend

LED+ LED-

AC2AC1

www.ti.com

PCB Cutouts

4.1.1 LED+

The LED+ is the positive output terminal of the EVM (banana jack) to the anode of the LED string.

4.1.2 LED–

The LED– is the negative output terminal of the EVM (banana jack) to the cathode of the LED string.

4.2 Input Connections

The input terminals of the EVM are described in Section 4.2.1 and Section 4.2.2.

4.2.1 AC1

AC1 is the AC voltage input terminal to the input power source. Differential to the AC2 terminal, the EVM

accepts a DC voltage, AC voltage or an electronic transformer as its input power source.

4.2.2 AC2

AC2 is the AC voltage input terminal to the input power source. Differential to the AC1 terminal, the EVM

accepts a DC voltage, AC voltage or an electronic transformer as its input power source.

5 PCB Cutouts

The EVM can fit into the plastic compartment of a generic MR16 by removing the outer frame of the PCB

as indicated in the following figure:

Figure 3. Removing Outer Frame of the TPS92560MR16BSTEVM

SLVU822–December 2012 User's Guide for TPS92560MR16BSTEVM

TPS92560MR16BSTEVM

LED+ LED-

AC1 AC2

Voltage Source

(DC voltage / AC voltage / Electronic transformer)

Ammeter 1

Ammeter 2

Voltmeter 1

Voltmeter 2

LED string (6 serial LEDs)

TPS92560MR16BSTEVM

IIN

ILED

VLED

VIN

Test Requirements and Setup

www.ti.com

6 Test Requirements and Setup

6.1 Hardware Requirements

The EVM has different requirements on the power source depending on the type of power source being

used. The requirements are as listed in the following table:

Table 3. Hardware Requirements

Item Description Characteristics

Input Power Source

DC power source Generic DC power supply 0 VDC-18 VDC, 1.5 A

AC power source 12-VAC AC power supply (50/60Hz) 12 VAC nominal, 10 W

Magnetic transformer with 12-VAC output (50/60Hz)

Electronic transformer Generic electronic transformer for MR16/AR111 110 VAC/220 VAC nominal input

applications

Load

Serial LED string Power LED string of 6 serial LEDs 20-V nominal LED forward voltage

6.2 Hardware Setup

Figure 4. Connection Diagram of the TPS92560MR16BSTEVM

6User's Guide for TPS92560MR16BSTEVM SLVU822–December 2012

Submit Documentation Feedback

ILED

IIN

VIN

POUT

Efficiency PIN

= x 100%

VOUT x IOUT

POUT =

VIN x IIN

PIN =

www.ti.com

Test Requirements and Setup

• Connect an LED string of 6 six serial LEDs to the terminals LED+ and LED– of the EVM. An external

ammeter (Ammeter 2) can be used in series to the LED string as shown in Figure 4 to measure the

RMS LED current.

• Connect the power source (a 12-VDC power source, 12-VAC power source or electronic transformer) to

the terminals AC1 and AC2 of the EVM. An external ammeter (Ammeter 1) can be used in series to

the power source as shown in Figure 4 to measure the RMS input current. Do not make the connection

when the power source is turned on.

• A voltmeter (Voltmeter 2) can be connected across the LED+ and LED– terminals of the EVM to

measure the RMS forward voltage of the LED string.

• A voltmeter (Voltmeter 1) can be connected across the AC1 and AC2 terminals of the EVM to measure

the RMS input voltage of the EVM.

• Using the measured RMS input current, input voltage, output current and output voltage, the input

power, output power and efficiency are calculated using the following equations: (1)

(2)

(3)

6.3 Typical Waveforms

6 serial LEDs, TA= 25°C

ILED: 200 mA/DIV, IIN: 1 A/DIV, VIN: 20 V/DIV

Figure 5. Waveforms of Powering the TPS92560MR16BSTEVM with an Electronic Transformer

SLVU822–December 2012 User's Guide for TPS92560MR16BSTEVM

ILED

IIN

VIN

ILED

IIN

VIN

Test Requirements and Setup

www.ti.com

6 serial LEDs, TA= 25°C

ILED: 200 mA/DIV, IIN: 1 A/DIV, VIN: 20 V/DIV

Figure 6. Waveforms of Powering the TPS92560MR16BSTEVM with 12 VAC at 50 Hz

6 serial LEDs, TA= 25°C

ILED: 200 mA/DIV, IIN: 1 A/DIV, VIN: 10 V/DIV

Figure 7. Waveforms of Powering the TPS92560MR16BSTEVM with 12 VDC

8User's Guide for TPS92560MR16BSTEVM SLVU822–December 2012

Submit Documentation Feedback

www.ti.com

TPS92560MR16BSTEVM Assembly Drawings and Layout

7 TPS92560MR16BSTEVM Assembly Drawings and Layout

Figure 8. TPS92560MR16BSTEVM Top View

Figure 9. TPS92560MR16BSTEVM Bottom View

SLVU822–December 2012 User's Guide for TPS92560MR16BSTEVM

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO

BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH

ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This

notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety

programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and

therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal

Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer

use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will

be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and

power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local

laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this

radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory

authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SPACER

【【Important Notice for Users of this Product in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this

product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with

respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note

that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

http://www.tij.co.jp

【ご使用にあたっての注】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SPACER

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished

electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in

laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks

associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug

Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,

affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable

regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,

contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)

between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to

minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even

if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the

user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and

environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact

a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the

specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or

interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the

load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures

greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include

but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the

EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please

be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable

in electronic measurement and diagnostics normally found in development environments should use these EVMs.

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives

harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in

connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims

arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such

as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices

which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate

Assurance and Indemnity Agreement.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES

1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or

documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.

Acceptance of the EVM is expressly subject to the following terms and conditions.

1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility

evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not

finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For

clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions

set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software

1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,

or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production

system.

2Limited Warranty and Related Remedies/Disclaimers:

2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software

License Agreement.

2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM

to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment

by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any

way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or

instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as

mandated by government requirements. TI does not test all parameters of each EVM.

2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,

or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the

warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to

repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall

be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day

warranty period.

3Regulatory Notices:

3.1 United States

3.1.1 Notice applicable to EVMs not FCC-Approved:

This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit

to determine whether to incorporate such items in a finished product and software developers to write software applications for

use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless

all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause

harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is

designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of

an FCC license holder or must secure an experimental authorization under part 5 of this chapter.

3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:

CAUTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

FCC Interference Statement for Class A EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

SPACER

FCC Interference Statement for Class B EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

3.2 Canada

3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210

Concerning EVMs Including Radio Transmitters:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Concernant les EVMs avec appareils radio:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concerning EVMs Including Detachable Antennas:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types

listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.

Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le

présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le

manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne

non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de

l'émetteur

3.3 Japan

3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に

輸入される評価用キット、ボードについては、次のところをご覧ください。

http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page

3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified

by TI as conforming to Technical Regulations of Radio Law of Japan.

If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of

Japan to follow the instructions below with respect to EVMs:

1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal

Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for

Enforcement of Radio Law of Japan,

2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to

EVMs, or

3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan

with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note

that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.

SPACER

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】開発キットの中には技術基準適合証明を受けて

いないものがあります。技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの

措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用

いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。日本テキサス・イ

ンスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ

い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

SPACER

4EVM Use Restrictions and Warnings:

4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT

LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.

4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling

or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information

related to, for example, temperatures and voltages.

4.3 Safety-Related Warnings and Restrictions:

4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user

guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and

customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input

and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or

property damage. If there are questions concerning performance ratings and specifications, User should contact a TI

field representative prior to connecting interface electronics including input power and intended loads. Any loads applied

outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible

permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any

load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.

During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit

components may have elevated case temperatures. These components include but are not limited to linear regulators,

switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the

information in the associated documentation. When working with the EVM, please be aware that the EVM may become

very warm.

4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the

dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.

User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,

affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic

and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely

limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and

liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or

designees.

4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,

state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all

responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and

liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local

requirements.

5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate

as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as

accurate, complete, reliable, current, or error-free.

SPACER

6. Disclaimers:

6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE

DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY

THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.

6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND

CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY

OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD

PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY

INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF

THE EVM.

7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS

LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,

EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY

HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION

SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY

OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.

8. Limitations on Damages and Liability:

8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,

INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE

TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED

TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,

LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL

BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.

8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION

ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM

PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER

THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE

OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND

CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.

9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)

will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in

a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable

order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),

excluding any postage or packaging costs.

10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,

without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to

these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.

Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief

in any United States or foreign court.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

spacer

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

TPS92560MR16BSTEVM