VOFFSET 600V or 1200V max.
IO+/- 200 mA / 420 mA
VOUT 10 - 20V or 12 - 20V
ton/off (typ.) 750/700 ns
Deadtime (typ.) 250 ns
Product Summary
3-PHASE BRIDGE DRIVER
IR2133/IR2135(J&S) & (PbF)
IR2233/IR2235(J&S) & (PbF)
Data Sheet No. PD60107 revX
www.irf.com 1
Features
••
••
• Floating channel designed for bootstrap operation
Fully operational to +600V or+1200V
Tolerant to negative transient voltage
dV/dt immune
••
••
• Gate drive supply range from 10V/12V to 20V DC and
up to 25V for transient
••
••
• Undervoltage lockout for all channels
••
••
• Over-current shut down turns off all six drivers
••
••
• Independent 3 half-bridge drivers
••
••
• Matched propagation delay for all channels
••
••
• 2.5V logic compatible
••
••
• Outputs out of phase with inputs
••
••
• All parts are also available LEAD-FREE
Description
The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed
power MOSFET and IGBT driver with three independent high side and
low side referenced output channels for 3-phase applications. Propri-
etary HVIC technology enables ruggedized monolithic construction.
Logic inputs are compatible with CMOS or LSTTL outputs, down to
2.5V logic. An independent operational amplifier provides an analog
feedback of bridge current via an external current sense resistor. A
current trip function which terminates all six outputs can also be de-
rived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to
indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The
output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are
matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or
IGBTs in the high side configuration which operates up to 600 volts or 1200 volts.
up to 600V or 1200V
Typical Connection
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only.
Please refer to our Application Notes and DesignTips for proper circuit board layout.
Packages
28-Lead SOIC
44-Lead PLCC w/o 12 leads
28-Lead PDIP
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
2www.irf.com
Absolute Maximum Ratings
Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All volt-
age parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation
ratings are measured under board mounted and still air conditions.
Recommended Operating Conditions
The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the
recommended conditions. All voltage parameters are absolute voltages referenced to COM. The VS offset rating is
tested with all supplies biased at 15V differential.
Note 1: Logic operational for VS of COM - 5V to COM + 600V/1200V. Logic state held for VS of COM -5V to COM -VBS. (Please refer to the Design Tip
DT97-3 for more details).
Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode.
Symbol Definition Min. Max. Units
VB1,2,3 High side floating supply voltage (IR2133/IR2135) -0.3 625
(IR2233/IR2235) -0.3 1225
VS1,2,3 High side floating supply offset voltage VB1,2,3 - 25 VB1,2,3 + 0.3
VHO1,2,3 High side floating output voltage VS1,2,3 - 0.3 VB1,2,3 + 0.3
VCC Fixed supply voltage -0.3 25
VSS Logic ground VCC - 25 VCC + 0.3
VLO1,2,3 Low side output voltage -0.3 VCC + 0.3
VIN Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) VSS - 0.3 (VSS + 15) or
(VCC + 0.3)
whichever is
lower
VIN,AMP Op amp input voltage (CA+ & CA-) VSS - 0.3 VCC + 0.3
VOUT,AMP Op amp output voltage (CAO) VSS - 0.3 VCC + 0.3
VFLT FAULT output voltage VSS - 0.3 VCC + 0.3
dVS/dt Allowable offset supply voltage transient — 50
PDPackage power dissipation @ TA ≤ 25ºC (28 Lead PDIP) — 1.5
(28 Lead SOIC) — 1.6
(44 lead PLCC) — 2.0
RthJA Thermal resistance, junction to ambient (28 Lead PDIP) — 83
(28 Lead SOIC) — 78
(44 lead PLCC) — 63
TJJunction temperature — 125
TSStorage temperature -55 150
TLLead temperature (soldering, 10 seconds — 300
ºC
W
VB1,2,3 High side floating supply voltage VS1,2,3 + 10/12 VS1,2,3 + 20
VS1,2,3 High side floating supply offset voltage (IR2133/IR2135) Note 1 600
(IR2233/IR2235) Note 1 1200
VHO1,2,3 High side floating output voltage VS1,2,3 VB1,2,3
VCC Fixed supply voltage 10 or 12 20
VSS Low side driver return -5 5
VLO1,2,3 Low side output voltage 0 VCC
VIN Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) VSS VSS + 5
VIN,AMP Op amp input voltage (CA+ & CA-) VSS VSS + 5
VOUT,AMP Op amp output voltage (CAO) VSS VSS + 5
VFLT FAULT output voltage VSS VCC
V
Symbol Parameter Definition Min. Max. Units
V/ns
V
ºC/W
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 3
Static Electrical Characteristics
VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. All static parameters other than IO and VO
are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are
referenced to COM and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3.
VIH Logic “0” Input Voltage (OUT = LO) 2.2 — —
VIL Logic “1” Input Voltage (OUT = HI) — — 0.8
VFCLR,IH Logic “0” Fault Clear Input Voltage 2.2 — —
VFCLR,IL Logic “1” Fault Clear Input Voltage — — 0.8
VSD,TH+SD Input Positive Going Threshold 1.6 1.9 2.2
VSD,TH-SD Input Negative Going Threshold 1.4 1.7 2.0
VIT,TH+IITRIP Input Positive Going Threshold 470 570 670
VIT,TH-IITRIP Input Negative Going Threshold 360 460 560
VOH High Level Output Voltage, VBIAS - VO— — 100 VIN = 0V, IO = 0A
VOL Low Level Output Voltage, VO— — 100 VIN = 5V, IO = 0A
ILK Offset Supply Leakage Current (IR2133/IR2135) — — 50 VB1,2,3=VS1,2,3 = 600V
(IR2233/IR2235) — — 50 VB1,2,3=VS1,2,3 = 1200V
IQBS Quiescent VBS Supply Current — 50 100 VIN = 0V or 5V
IQCC Quiescent VCC Supply Current — 4 8 mA VIN = 0V or 5V
IIN+Logic “1” Input Bias Current (OUT = HI) — 200 350 VIN = 0V
IIN-Logic “0” Input Bias Current (OUT = LO) — 100 250 VIN = 5V
ISD+“High” Shutdown Bias Current — 30 100 SD = 5V
ISD-“Low” Shutdown Bias Current — — 100 nA SD = 0V
IITRIP+“High” IITRIP Bias Current — 30 100 µA IITRIP = 5V
IITRIP-“Low” IITRIP Bias Current — — 100 nA IITRIP = 0V
Symbol
V
µA
Dynamic Electrical Characteristics
VBIAS (VCC, VBS1,2,3) = 15V, VS1,2,3 = VSS, TA = 25oC and CL = 1000 pF unless otherwise specified.
Definition Min. Typ. Max. Units Test Conditions
ton Turn-on propagation delay 500 750 1000
toff Turn-off propagation delay 450 700 950
trTurn-on rise time — 90 150
tfTurn-off fall time — 40 70
tsd SD to output shutdown propagation delay 500 750 1000 VIN,VSD = 0 & 5V
titrip ITRIP to output shutdown propagation delay 600 850 1100 VIN,VITRIP = 0 & 5V
tbl ITRIP blanking time — 400 — ITRIP = 1V
tflt ITRIP to FAULT propagation delay 400 650 900 VIN,VITRIP = 0 & 5V
tfil,in Input filter time (HIN, LIN and SD) — 310 — VIN = 0 & 5V
tfltclr FLT-CLR to FAULT clear time 600 850 1100 VIN,VITRIP = 0 & 5V
DT Deadtime, LS turn-off to HS turn-on & 100 250 400 VIN = 0 & 5V
HS turn-off to LS turn-on
SR+ Amplifier slew rate (positive) 5 10 —
SR- Amplifier slew rate (negative) 2 2.5 —
Symbol
V/µs
ns
VIN = 0 & 5V
VS1,2,3 = 0 to 600V
or 1200V
Definition Min. Typ. Max. Units Test Conditions
NOTE: For high side PWM, HIN pulse width must be ≥ 1µ sec
mV
µA
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
4www.irf.com
Static Electrical Characteristics — Continued
VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. All static parameters other than IO and VO
are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are
referenced to COM and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3.
µA
Symbol
PW ≤ 10 µs
Parameter Definition Min. Typ. Max. Units Test Conditions
IFLTCLR+ “High” Fault Clear Input Bias Current — 200 350 FLT-CLR = 0V
IFLTCLR- “Low” Fault Clear Input Bias Current — 100 250 FLT-CLR = 5V
VBSUV+VBS Supply Undervoltage Positive Going Threshold
(for IR2133/IR2233) 7.6 8.6 9.6
(for IR2135/IR2235) 9.2 10.4 11.6
VBSUV-VBS Supply Undervoltage Negative Going Threshold
(for IR2133/IR2233) 7.2 8.2 9.2
(for IR2135/IR2235) 8.3 9.4 10.5
VBSUVH VBS Supply Undervoltage Lockout Hysteresis
(for IR2133/IR2233) — 0.4 —
(for IR2135/IR2235) — 1 —
VCCUV+VCC Supply Undervoltage Positive Going Threshold
(for IR2133/IR2233) 7.6 8.6 9.6
(for IR2135/IR2235) 9.2 10.4 11.6
VCCUV-VCC Supply Undervoltage Negative Going Threshold
(for IR2133/IR2233) 7.2 8.2 9.2
(for IR2135/IR2235) 8.3 9.4 10.5
VCCUVH VCC Supply Undervoltage Lockout Hysteresis
(for IR2133/IR2233) — 0.4 —
(for IR2135/IR2235) — 1 —
Ron,FLT FAULT- Low On Resistance — 70 100 Ω
IO+Output High Short Circuit Pulsed Current 200 250 — VOUT = 0V, VIN = 0V
IO-Output Low Short Circuit Pulsed Current 420 500 — VOUT = 15V, VIN = 5V
VOS Amplifier Input Offset Voltage — 0 30 mV CA+=0.2V, CA-=CAO
IIN,AMP Amplifier Input Bias Current — — 4 nA CA+ = CA- = 2.5V
CMRR Amplifier Common Mode Rejection Ratio 50 70 — CA+ = 0.1V & 5V, CA- = CAO
PSRR Amplifier Power Supply Rejection Ratio 50 70 — CA+=0.2V, CA-=CAO
VOH,Amp Amplifier High Level Output Voltage 5 5.2 5.4 V CA+ = 1V, CA- = 0V
VOL,Amp Amplifier Low Level Output Voltage — — 20 mV CA+ = 0V, CA- = 1V
ISRC,Amp Amplifier Output Source Current 4 7 — CA+ = 1V, CA- = 0V, CAO = 4V
ISNK,Amp Amplifier Output Sink Current 0.5 1 — CA+ = 0V, CA- = 1V, CAO = 2V
IO+,Amp Amplifier Output High Short Circuit Current — 10 — CA+ = 5V, CA- = 0V, CAO = 0V
IO-,Amp Amplifier Output Low Short Circuit Current — 4 — CA+ = 0V, CA- = 5V, CAO = 5V
mA
VCC = 10V & 20V
dB
mA
PW ≤ 10 µs
V
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 5
Functional Block Diagram
Lead Definitions
Symbol Lead Description
HIN1,2,3 Logic inputs for high side gate driver outputs (HO1,2,3), out of phase.
LIN1,2,3 Logic inputs for low side gate driver outputs (LO1,2,3), out of phase.
FAULT Indicates over-current or undervoltage lockout (low side) has occurred, negative logic.
VCC Logic and low side fixed supply.
ITRIP Input for over-current shut down.
FLT-CLR Logic input for fault clear, negative logic.
SD Logic input for shut down.
CAO Output of current amplifier.
CA- Negative input of current amplifier.
CA+ Positive input of current amplifier.
VSS Logic ground.
COM Low side return.
VB1,2,3 High side floating supplies.
HO1,2,3 High side gate drive outputs.
VS1,2,3 High side floating supply returns.
LO1,2,3 Low side gate drive outputs
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
6www.irf.com
Lead Assignments
ITRIP
FLT-CLR
CAO
CA-
CA+
SD
VSS
COM
LO3
LO2
LO1
VS3
HO3
VB3
FAULT
LIN3
LIN2
LIN1
HIN3
HIN2
HIN1
VCC
VB1
HO1
VS1
VB2
HO2
VS2
ITRIP
FLT-CLR
CAO
CA-
CA+
SD
VSS
COM
LO3
LO2
LO1
VS3
HO3
VB3
FAULT
LIN3
LIN2
LIN1
HIN3
HIN2
HIN1
VCC
VB1
HO1
VS1
VB2
HO2
VS2
28 Lead DIP 44 Lead PLCC w/o 12 Leads 28 Lead SOIC (Wide Body)
IR2133
IR2135
IR2133J
IR2135J
IR2233J
IR2235J
IR2133S
IR2135S
IR2233S
IR2235S
Part Number
Figure 1. Input/Output Timing Diagram
SD
ITRIP
HIN
1,2,3
LIN
1,2,3
HO1
,
2
,
3
LO1
,
2
,
3
FLT-CLR
FAULT
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 7
FLT-CLR
tflt
Any Output
50%
50%
ITRIP
FAULT
tfltclr
titrip
50%
50%
50%
Figure 4. Overcurrent Shutdown Waveform
HI
N
50% 50%
DT
50% 50%
LIN
DT
HO
LO
Figure 3. Deadtime Waveform Definitions
HIN
LIN
tr
ton tf
toff
HO
LO
50% 50%
90% 90%
10% 10%
Figure 2. Switching Time Waveform Definitions
U
tin,fil tin,fil
on on on off
offoff
high
low
HIN/LIN
HO/LO
Figure 4.5. Input Filter Function Figure 5. Shutdown Waveform Definitions
SD
tsd
HO
LO
50%
90%
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
8www.irf.com
Min.
Typ.
M ax.
0
300
600
900
1200
1500
-50-25 0 255075100125
Temperature (oC)
Turn-on Delay Time (ns
)
Figure 6A. Turn-On Time vs. Temperature
Min.
Typ.
M ax.
0
300
600
900
1200
1500
10 12.5 15 17.5 20
Supply Voltage (V)
Turn-on Delay Time (ns
)
Figure 6B. Turn-On Time vs. Voltage
Max.
Typ.
Min.
0
300
600
900
1200
1500
-50 -25 0 25 50 75 100 125
Temperature (oC)
Turn-Off Time (ns)
Figure 7A. Turn-Off Time vs. Temperature
Min.
Typ.
M ax.
0
300
600
900
1200
1500
2.5 3 3.5 4 4.5 5
Input Voltage (V)
Turn-on Delay Time (ns
)
Figure 6C. Turn-On Time vs. Input Voltage
Min.
Typ.
M ax.
0
300
600
900
1200
1500
10 12.5 15 17.5 20
Supply Voltage (V)
Turn-Off Time (ns)
Figure 7B. Turn-Off Time vs. Voltage
Typ.
Min.
M ax.
0
300
600
900
1200
1500
2.5 3 3.5 4 4.5 5
Input Voltage (V)
Turn-Off Time (ns)
Figure 7C. Turn-Off Time vs. Input
Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 9
M ax.
Typ.
0
50
100
150
200
250
-50 -25 0 25 50 75 100 125
Temperature (oC)
Turn-On Rise Time (ns
Fiure 8A. Turn-On Rise Time vs.Temperature
Typ.
M ax.
0
50
100
150
200
250
10 12.5 15 17.5 20
Supply Voltage (V)
Turn-On Rise Time (ns
Fiure 8B. Turn-On Rise Time vs.Voltage
Typ.
M ax.
0
30
60
90
120
150
-50 -25 0 25 50 75 100 125
Temperature (oC)
Turn-Off Fall Tim
e
Figure 9A. Turn-Off Fall Time vs. Temperature
Typ.
M ax.
0
30
60
90
120
150
10 12.5 15 17.5 20
Supply Voltage (V)
Turn-Off Fall Tim
e
Figure 9B. Turn-Off Fall Time vs. Voltage
Min.
Typ.
M ax.
0
300
600
900
1200
1500
-50-25 0 25 50 75100125
Temperature (oC)
SD to output SD Time (ns
)
Figure 10A. SD to Output shutdow n Time
vs. Te m perature
Min.
Typ.
M ax.
0
300
600
900
1200
1500
10 12.5 15 17.5 20
Supply Voltage (V)
SD to output SD Time (ns
)
Figure 10B. SD to Output shutdown Time
vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
10 www.irf.com
Min.
Typ.
M ax.
0
300
600
900
1200
1500
-50-25 0 25 50 75100125
Temperature (oC)
ITRIP to FAULT Time (n
s
_____
Figure 11A. ITRIP to FAULT Time
vs. Te m perature
Min.
Typ.
M ax.
0
300
600
900
1200
1500
10 12.5 15 17.5 20
Supply Voltage (V)
ITRIP to FAULT Time (n
s
_____
Figure 11B. ITRIP to FAULT Time
vs. Voltage
Min.
Typ.
M ax.
300
600
900
1200
1500
1800
-50 -25 0 25 50 75 100 125
Temperature (oC)
ITRIP to output SD Time (n
s
Figure 12A. ITRIP to output shutdow n Time
vs. Te m perature
Min.
Typ.
M ax.
300
600
900
1200
1500
1800
10 12.5 15 17.5 20
Supply Voltage (V)
ITRIP to output SD Time (n
s
Figure 12B. ITRIP to output shutdow n Time
vs. Voltage
Min.
Typ.
M ax.
300
600
900
1200
1500
1800
-50-25 0 25 50 75100125
Temperature (oC)
FLT-CLR to FAULT clear Time (n
s
________ ______
Figure 13A. FLT-CLR to FAULT clear Time
vs. Te m perature
Min.
Typ.
M ax.
300
600
900
1200
1500
1800
10 12.5 15 17.5 20
Supply Voltage (V)
FLT-CLR to FAULT clear Time (n
s
________ ______
Figure 13B. FLT-CLR to FAULT clear Time
vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 11
M ax.
Typ.
Min.
0
150
300
450
600
750
-50 -25 0 25 50 75 100 125
Temperature (oC)
Deadtime (ns)
Figure 14A. Deadtime vs. Temperature
Min.
Typ.
M ax.
0
150
300
450
600
750
10 12.5 15 17.5 20
Supply Voltage (V)
Deadtime (ns)
Figure 14B. Deadtime vs. Voltage
Min.
Typ.
0
4
8
12
16
20
-50 -25 0 25 50 75 100 125
Temperature (oC)
Amplifier slew rate (v/ µs)
Figure 15A. Amplifier slew rate (+)
vs. Temperature
Min.
Typ.
0
4
8
12
16
20
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier slew rate (v/ µs)
Figure 15B. Am plifier slew rate (+)
vs. Voltage
Min.
Typ.
0
1
2
3
4
5
-50-250 255075100125
Temperature (oC)
Amplifier slew rate (v/ µs)
Figure 16A. Amplifier slew rate (-)
vs. Temperature
Min.
Typ.
1
2
3
4
5
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier slew rate (v/ µs)
Figure 16B. Amplifier slew rate (-)
vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
12 www.irf.com
Min.
1
2
3
4
5
6
-50 -25 0 25 50 75 100 125
Temperature (oC)
Logic "0" Input Voltage (V)
Figure 17A. Logic "0" Input Voltage (OUT=LO),
Fault Clear Voltage vs. Temperature
Min.
1
2
3
4
5
6
10 12.5 15 17.5 20
Supply Voltage (V)
Logic "0" Input Voltage (V)
Figure 17B. Logic "0" Input Voltage (OUT=LO),
Fault Clear Voltage vs. Voltage
M ax.
0
1
2
3
4
5
-50 -25 0 25 50 75 100 125
Temper atr e ( oC)
Logic "1" Input Voltage (V)
Figure 18A. Logic "1" Input (OUT=HI), Fault
Clear Input Voltage vs. Temperature
M ax.
0
1
2
3
4
5
10 12.5 15 17.5 20
Supply Voltage (V)
Logic "1" Input Voltage (V)
Figure 18B. Logic "1" Input (OUT=HI), Fault
Clear Input Voltage vs. Voltage
Min.
Typ.
M ax.
1.0
1.5
2.0
2.5
3.0
-50 -25 0 25 50 75 100 125
Temper atr e ( oC)
SD Input TH (+) (V
)
Figure 21A. SD Input TH(+) vs.
Temperature
Min.
Typ.
M ax.
1.0
1.5
2.0
2.5
3.0
10 12.5 15 17.5 20
Supply Voltage (V)
SD Input TH (+) (V
)
Figure 21B. SD Input TH(+) vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 13
Min.
Typ.
M ax.
1.0
1.5
2.0
2.5
3.0
-50 -25 0 25 50 75 100 125
Temper atr e ( oC)
SD Input TH (-) (V
)
Figure 22A. SD Input TH(-) vs. Temperature
Min.
Typ.
M ax.
1.0
1.5
2.0
2.5
3.0
10 12.5 15 17.5 20
Supply Voltage (V)
SD Input TH (-) (V
)
Figure 22B. SD Input TH(-) vs. Voltage
Min.
Typ.
M ax.
200
400
600
800
1000
-50-25 0 255075100125
Temperature (oC)
IITRIP Input TH (+) (mV
)
Figure 23A. IITRIP Input TH(+) vs. Temperature
Min.
Typ.
Max.
200
400
600
800
1000
10 12.5 15 17.5 20
Supply Voltage (V)
IITRIP Input TH (+) (mV
)
Figure 23B. IITRIP Input TH(+) vs. Voltage
Min.
Typ.
M ax.
100
300
500
700
900
-50 -25 0 25 50 75 100 125
Temperature (oC)
IITRIP Input TH (-) (mV
)
Figure 24A. IITRIP Input TH(-) vs.Temperature
Min.
Typ.
M ax.
100
300
500
700
900
10 12.5 15 17.5 20
Supply Voltage (V)
IITRIP Input TH (-) (mV
)
Figu r e 24B. IITRIP Input TH(-) vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
14 www.irf.com
M ax.
0.0
0.1
0.2
0.3
0.4
0.5
-50 -25 0 25 50 75 100 125
Temperature (oC)
High Level Output Voltage (V)
Figure 25A. High Level Output vs. Temperature
M ax.
0.0
0.1
0.2
0.3
0.4
0.5
10 12.5 15 17.5 20
Supply Voltage (V)
High Level Output Voltage (V)
Figure 25B. High Level Output vs. Voltage
M ax.
0
0.1
0.2
0.3
0.4
0.5
-50 -25 0 25 50 75 100 125
Temperature (oC)
Low Level Output Voltage (V)
Figure 26A. Low Level Output vs. Temperature
M ax.
0
0.1
0.2
0.3
0.4
0.5
10 12.5 15 17.5 20
Supply Voltage (V)
Low Level Output Voltage (V)
Figure 26B. Low Level Output vs. Voltage
M ax.
0
100
200
300
400
500
-50 -25 0 25 50 75 100 125
Temperature (oC)
Offset Supply Leakage Current (µA)
Figure 27A. Offset Supply Leakage
Current vs. Temperature
M ax.
0
100
200
300
400
500
0 100 200 300 400 500 600
Supply Voltage (v)
Offset Supply Leakage Current (µA)
Figure 27B. Offset Supply Leakage
Current vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 15
M ax.
Typ.
0
50
100
150
200
250
-50-250 255075100125
Temperature (oC)
V Supply Current (µΑ)
Figure 28A. VBS Supply Current
vs. Temperature
M ax.
Typ.
0
50
100
150
200
250
10 12.5 15 17.5 20
Supply Voltage (V)
V Supply Current (µΑ)
Figure 28B. VBS Supply Current
vs. Voltage
Typ.
M ax.
0
4
8
12
16
20
-50-25 0 25 50 75100125
Temperature (oC)
Vcc Supply Current (µA)
Figure 29A. Vcc Supply Current vs.
Temperature
M ax.
Typ.
0
4
8
12
16
20
10 12.5 15 17.5 20
Supply Voltage (V)
Vcc Supply Current (µA)
Figu r e 29B. Vcc Supply Current vs. Voltage
Typ.
M ax.
0
200
400
600
800
-50-25 0 25 50 75100125
Temperature (oC)
Logic "1" Input Current (
µA)
Figure 30A. Logic "1" Input Bais Current
vs. Temperature
M ax.
Typ.
0
200
400
600
800
10 12.5 15 17.5 20
Supply Voltage (V)
Logic "1" Input Current (
µA)
Figure 30B. Logic "1" Input Bais Current
vs. Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
16 www.irf.com
M ax.
Typ.
0
200
400
600
800
-50-25 0 25 50 75100125
Temperature (oC)
Logic "0" Input Current (
µA)
Figure 31A. Logic "0" Input Bais Current
vs. Temperature
Typ.
M ax.
0
200
400
600
800
10 12.5 15 17.5 20
Supply Voltage (V)
Logic "0" Input Current (
µA)
Figure 31B. Logic "0" Input Bais Current
vs. Supply Voltage
Typ.
M ax.
0
100
200
300
400
-50-25 0 255075100125
Temperature (oC)
"High" SD Bais Current (
µA)
Figure 32A. "High" Shutdow n Bais Current
vs. Temperature
Typ.
M ax.
0
100
200
300
400
10 12.5 15 17.5 20
Supply Voltage (V)
"High" SD Bais Current (
µA)
Figure 32B. "High" Shutdow n Bais Current
vs. Supply Voltage
M ax.
0
100
200
300
400
500
-50 -25 0 25 50 75 100 125
Temperature (oC)
"Low" SD Bais Current (nA)
Figure 33A. "Low" Shutdow n Bais Current
vs. Temperature
M ax.
0
100
200
300
400
500
10 12.5 15 17.5 20
Supply Voltage (V)
"Low" SD Bais Current (nA)
Figure 33B. "Low " Shutdown Bais Current
vs. Supply Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 17
Typ.
M ax.
0
100
200
300
400
-50 -25 0 25 50 75 100 125
Temperature (oC)
"High" I
ITRIP Bias Current (µA)
Figure 34A. "High" IITRIP Bais Current
vs. Temperature
Typ.
M ax.
0
100
200
300
400
10 12.5 15 17.5 20
Supply Voltage (V)
"High" I
ITRIP Bias Current (µA)
Figure 34B. "High" IITRIP Bais Current
vs. Supply Voltage
M ax.
0
100
200
300
400
500
-50-250 255075100125
Temperature (oC)
"Low" IITRIP Bais Current (nA)
Figure 35A. "Low" IITRIP Bais Current
vs. Temperature
M ax.
0
100
200
300
400
500
10 12.5 15 17.5 20
Supply Voltage (V)
"Low" IITRIP Bais Current (nA)
Figure 35B. "Low" IITRIP Bais Current
vs. Supply Voltage
Typ.
M ax.
0
200
400
600
800
-50-25 0 25 50 75100125
Temperature (oC)
"High" Fault Clear Input Current (
µA)
Figure 36A. "High" Fault Clear Input Bais Current
vs. Temperature
Typ.
M ax.
0
200
400
600
800
10 12.5 15 17.5 20
Supply Voltage (V)
"High" Fault Clear Input Current (
µA)
Figure 36B. "High" Fault Clear Input Bais Current
vs. Supply voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
18 www.irf.com
Typ.
M ax.
0
200
400
600
800
-50-25 0 25 50 75100125
Temperature (oC)
"Low" Fault Clear Input Current (
µA)
Figure 37A. "Low" Fault Clear Input Bais Current
vs. Temperature
Typ.
M ax.
0
200
400
600
800
10 12.5 15 17.5 20
Supply Voltage (V)
"Low" Fault Clear Input Current (
µA)
Figure 37B. "Low" Fault Clear Input Bais Current
vs. Supply Voltage
Min.
Typ.
M ax.
6
8
10
12
14
-50 -25 0 25 50 75 100 125
Temperature (oC)
VBS UV Th (+) (V)
Figure 38A. IR2135/IR2235 VBS Undervoltage
Threshold (+) vs. Temperature
Min.
Typ.
M ax.
6
8
9
11
12
-50 -25 0 25 50 75 100 125
Temperature (oC)
VBS UV Th (+) (V)
Figure 38B. IR2133/IR2233 VBS Undervoltage
Threshold (+) vs. Temperature
Min.
Typ.
M ax.
6
8
10
12
14
-50 -25 0 25 50 75 100 125
Temperature (oC)
V UV TH (+) (V)
Figur e 39A. IR2135/IR2235 VBS Undervoltage
Threshold (-) vs. Temperature
Typ.
Min.
M ax.
6
8
9
11
12
-50 -25 0 25 50 75 100 125
Temperature (oC)
V UV TH (+) (V)
Figure 39B. IR2133/IR2233 VBS Undervoltage
Threshold (-) vs. Temperature
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 19
Min.
Typ.
M ax.
8
10
11
13
14
-50 -25 0 25 50 75 100 125
Temperature (oC)
Vcc UV TH (+) (V)
Figur e 40A. IR2135/IR2235 Vcc Undervoltage
Threshold (+) vs. Temperature
Typ.
M ax.
Min.
6
8
9
11
12
-50-25 0 25 50 75100125
Temperature (oC)
Vcc UV TH (+) (V)
Figure 40B. IR2133/IR2233 Vcc Undervoltage
Threshold (+) vs. Temperature
Typ.
Min.
M ax.
6
8
9
11
12
-50 -25 0 25 50 75 100 125
Temperature (oC)
Vcc UV TH (+) (V)
Figur e 41A. IR2135/IR2235 Vcc Undervoltage
Threshold (-) vs. Temperature
Typ.
Min.
M ax.
6
8
9
11
12
-50 -25 0 25 50 75 100 125
Temperature (oC)
Vcc UV TH (+) (V)
Figur e 41B. IR2133/IR2233 Vcc Undervoltage
Threshold (-) vs. Temperature
Typ.
M ax.
0
50
100
150
200
-50 -25 0 25 50 75 100 125
FAULT-Low On Resistance (
Ω)
Figure 42A. FAULT- Low On Resistance
vs. Temperature
Temperature (oC)
Typ.
M ax.
0
30
60
90
120
150
10 12.5 15 17.5 20
Supply Voltage (V)
FAULT-Low On Resistance (
Ω)
Figure 42B. FAULT- Low On Resistance
vs. Supply Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
20 www.irf.com
Min.
Typ.
0
100
200
300
400
500
-50 -25 0 25 50 75 100 125
Output Source Current (m
Α)
Figure 43A. Output Source Current
vs. Temperature
Temperature (oC)
Min.
Typ.
0
100
200
300
400
500
10 12.5 15 17.5 20
Output Source Current (m
Α)
Figure 43B. Output Source Current
vs. Supply Voltage
Supply voltage (V)
Min.
Typ.
0
200
400
600
800
1000
-50 -25 0 25 50 75 100 125
Temperature (oC)
Output Sink Current (m
Α)
Figure 44A. Ourput Sink Current
vs. Temperature
Min.
Typ.
0
200
400
600
800
1000
10 12.5 15 17.5 20
Supply Voltage (V)
Output Sink Current (m
Α)
Figure 44B. Ourput Sink Current
vs. Supply Voltage
M ax.
Typ.
-10
10
30
50
70
90
-50 -25 0 25 50 75 100 125
Temperature (oC)
Amplifier Input Offset Voltage (mV)
Figure 45A. Amplifier Input Offest Voltage
vs. Temperature
Typ.
M ax.
-10
10
30
50
70
90
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier Input Offset Voltage (mV)
Figure 45B. Amplifier Input Offest Voltage
vs. Supply Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 21
Min.
Typ.
0
30
60
90
120
150
-50 -25 0 25 50 75 100 125
Temperature (oC)
Amplifier CMRR (dB)
Figure 46A. Amplifier Common Mode Rejection
Ratio vs. Temperature
Min.
Typ.
0
30
60
90
120
150
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier CMRR (dB
)
Figure 46B. Amplifier Common Mode Rejection
Ratio vs. Supply Voltage
Min.
Typ.
0
25
50
75
100
125
-50 -25 0 25 50 75 100 125
Temperature (oC)
Amplifier PSRR (dB)
Figure 47A. Amplifier Pow er Supply Rejection
Ratio vs. Temperature
Min.
Typ.
0
25
50
75
100
125
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier PSRR (dB)
Figure 47B. Amplifier Power Supply Rejection
Ratio vs. Supply Voltage
Typ.
M ax.
Min.
4.5
4.8
5.1
5.4
5.7
6.0
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier V OH (V)
Figure 48. Amplifier High Level Output Voltage
vs. Supply Voltage
M ax.
0
10
20
30
40
50
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier V OL (V)
Figure 49. Amplifier Low Level Output Voltage
vs. Supply Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
22 www.irf.com
Min.
Typ.
0
3
6
9
12
15
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier ISRC(V)
Figure 50. Amplifier Output Source Current
vs. Supply Voltage
Min.
Typ.
0.0
0.5
1.0
1.5
2.0
2.5
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier ISNK(V)
Figure 51. Amplifier Output Sink Current
vs. Supply Voltage
Typ.
0
4
8
12
16
20
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier IO+ (V)
Figure 52. Amplifier Output High Short Circuit
Current vs. Supply Voltage
Typ.
0
4
8
12
16
20
10 12.5 15 17.5 20
Supply Voltage (V)
Amplifier IO- (V)
Figure 53. Amplifier Output Low Short Circuit
Current vs. Supply Voltage
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 23
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
Juntion Tem per ature (°C)
480
320V
160
0V
Figure 8. IR2133J Junction Temperature vs
Frequency Driving (IRGPC30KD2) Rgate = 5.1Ω @
Vcc = 15V
Frequency (Hz)
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
Juntion Tem per atur e (°C )
480V
320V
160V
0V
Figure 7. IR2133J Junction Temperature vs
Frequency Driving (IRGPC20KD2) Rgate = 5.1Ω @
Vcc = 15V
Frequency (Hz)
Figure 9. IR2133J Junction Temperature vs
Frequency Driving (IRGPC40KD2) Rgate = 5.1Ω @
Vcc = 15V
Frequency (Hz)
20
30
40
50
60
70
80
90
100
110
120
130
140
150
1E+2 1E+3 1E+4 1E+5
Junction Tem peratur e (°C)
480V
320V
160V
0V
Figure 10. IR2133J Junction Temperature vs
Frequency Driving (IRGPC50KD2) Rgate = 5.1Ω @
Vcc = 15V
Frequency (Hz)
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
Junction Tem peratur e (°C )
480V
320V
160V
0V
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
24 www.irf.com
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
Junction Tem perature (°C )
500V
300V
0V
900V
Figure 14. IR2233J Junction Temperature vs
Frequency Driving (IRG4ZH71KD) Rgate = 5Ω @
Vcc = 15V
Frequency (Hz)
Figure 13. IR2233J Junction Temperature vs
Frequency Driving (IRG4PH50KD) Rgate = 10Ω @
Vcc = 15V
Frequency (Hz)
Junction Tem perature (°C )
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
500V 300V
0V
900V
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
Junction Tem perature (°C )
900V
500
300V
0V
Figure 11. IR2233J Junction Temperature vs
Frequency Driving (IRG4PH30KD) Rgate = 20Ω @
Vcc = 15V
Frequency (Hz)
20
30
40
50
60
70
80
90
100
110
120
1E+2 1E+3 1E+4 1E+5
900V
300
500V
0V
Frequency (Hz)
Figure 12. IR2233J Junction Temperature vs
Frequency Driving (IRG4PH40KD) Rgate = 15Ω @
Vcc = 15V
1
1
1
Junction Tem per atur e (°C)
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 25
Package Dimensions
28-Lead PDIP (wide body) 01-6011
01-3024 02 (MS-011AB)
28-Lead SOIC (wide body) 01-6013
01-3040 02 (MS-013AE)
NOTES
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
26 www.irf.com
01-6009 00
01-3004 02(mod.) (MS-018AC)
44-Lead PLCC w/o 12 leads
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
www.irf.com 27
LEADFREE PART MARKING INFORMATION
ORDER INFORMATION
Basic Part (Non-Lead Free)
28-Lead PDIP IR2133 order IR2133 2
8-Lead SOIC IR2133S order IR2133S
28-Lead PDIP IR2135 order IR2135
28-Lead SOIC IR2135S order IR2135S
28-Lead PDIP IR2233 not available
28-Lead SOIC IR2233S order IR2233S
28-Lead PDIP IR2235 not available
28-Lead SOIC IR2235S order IR2235S
44-Lead PLCC IR2133J order IR2133J
44-Lead PLCC IR2135J order IR2135J
44-Lead PLCC IR2233J order IR2233J
44-Lead PLCC IR2235J order IR2235J
Leadfree Part
28-Lead PDIP IR2133 order IR2133PbF
28-Lead SOIC IR2133S order IR2133SPbF
28-Lead PDIP IR2135 order IR2135PbF
28-Lead SOIC IR2135S order IR2135SPbF
28-Lead PDIP IR2233 order IR2233PbF
28-Lead SOIC IR2233S order IR2233SPbF
28-Lead PDIP IR2235 order IR2235PbF
28-Lead SOIC IR2235S order IR2235SPbF
44-Lead PLCC IR2133J order IR2133JPbF
44-Lead PLCC IR2135J order IR2135JPbF
44-Lead PLCC IR2233J order IR2233JPbF
44-Lead PLCC IR2235J order IR2235JPbF
Lead Free Released
Non-Lead Free
Released
Part number
Date code
IRxxxxxx
YWW?
?XXXX
Pin 1
Identifier
IR logo
Lot Code
(Prod mode - 4 digit SPN code)
Assembly site code
Per SCOP 200-002
P
?MARKING CODE
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105
This product has been qualified per industrial level
Data and specifications subject to change without notice. 9/22/2005
