GLS85LS1032B-M-I-1S-ED100 - Greenliant

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

Features

 Industry Standard Serial ATA (SATA) Host Interface

- SATA 1.5 Gb/s or SATA 3.0 Gb/s 1)

- ATA/ATAPI-8 compliant

- Supports 48-bit address feature set

 Performance

- Sequential data read -

Up to 110 MByte/sec*

- Sequential data write -

Up to 60 MByte/sec*

* measured using 128 KByte transfer size

 Power Management

- 3.3V and 1.2Vpower supply

- Host SATA interface power management

- Immediate disabling of unused circuitry

without host intervention

 Power Specifications 2)

- Active mode:

820mW typical (GLS85LS1064B)

565mW typical (GLS85LS1032B)

440mW typical (GLS85LS1016B)

360mW typical (GLS85LS1008B)

360mW typical (GLS85LS1004A)

360mW typical (GLS85LS1002A)

- Idle / Standby mode: 210mW typical

- Sleep mode: 70mW typical

 Expanded Data Protection

- Added data security through user-selectable

protection zones

 Integrated Voltage Detector

- Detects supply voltage fluctuations and

generates reset during power-up and power-

down to prevent inadvertent writes

 Supports SMART Commands

 20-Byte Serial Number

- Factory pre-programmed 10-Byte unique ID

- User-programmable 10-Byte ID

 Robust Built-in ECC

 NAND Configuration

- 2 bits per cell (MLC)

 Temperature Range

- Commercial: 0°C to 70°C

- Industrial: -40°C to 85°C

 FBGA package

- 14.0 mm x 24.0 mm x 1.95 mm, 145-ball,

1.0 mm ball pitch, FZJE

 All Devices are RoHS Compliant

1) Current product revision supports SATA Revision 1.x with

host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s).

SATA 3.0 Gb/s refers to SATA Revision 2.x and will be

supported by our planned future product revisions.

2) For management of the Sleep Mode, refer to “SATA

NANDrive Application Design Guide.”

Product Description

The GLS85LS1002A / 1004A / 1008B / 1016B /

1032B / 1064B Industrial Temperature and

Commercial Temperature SATA NANDrive™ devices

(referred to as “SATA NANDrive” in this datasheet)

are fully integrated solid state drives. They combine

an advanced Greenliant NAND controller and 2, 4, 8,

16, 32 or 64 GByte of NAND flash in a multi-chip

package. These products are ideal for embedded and

portable applications that require smaller form factor

and more reliable data storage.

SATA-interface solid state mass storage technology is

widely used in portable and industrial computers, set-

top boxes, multi-functional printers, point-of-sales

terminals, video and audio recorders, medical

instruments and car infotainment systems.

SATA NANDrive is a single device, solid state drive

(SSD) that provides the functionality and compatibility

of a complete SATA hard disk drive (HDD) in a 14 mm

x 24 mm BGA package for easy, space saving

mounting to a system motherboard. These products

surpass traditional storage in their small size, security,

reliability, ruggedness and low power consumption.

The integrated NAND flash controller with built-in

advanced NAND management firmware

communicates with the host through the standard

SATA protocol. It does not require any additional or

proprietary software such as the Flash File System

(FFS) and Memory Technology Driver (MTD).

SATA NANDrive is pre-programmed with a 10-Byte

unique serial ID and has the option of programming

an additional 10-Byte serial ID for even greater

system security.

SATA NANDrive’s advanced NAND management

technology enhances data reliability and security,

improves endurance and accurately estimates the

remaining life of the NAND flash devices. This

innovative technology combines robust NAND

controller hardware error correction capabilities with

advanced wear-leveling algorithms and bad block

management to significantly extend the life of the

product.

SATA NANDrive devices are offered in a 145-ball

BGA, 1 mm ball pitch package.

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

1.0 GENERAL DESCRIPTION

Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete

NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram.

1.1 Optimized SATA NANDrive

The heart of SATA NANDrive is the SATA NAND flash

memory controller which translates standard SATA

signals into flash media data and control signals. The

following components contribute to SATA NANDrive’s

operation.

1.1.1 Microcontroller Unit (MCU)

The MCU translates SATA commands into data and

control signals required for flash media operation.

1.1.2 Internal Direct Memory Access (DMA)

SATA NANDrive uses internal DMA allowing instant

data transfer from/to buffer to/from flash media. This

implementation eliminates microcontroller overhead

associated with the traditional, firmware-based

approach, thereby increasing the data transfer rate.

1.1.3 Power Management Unit (PMU)

The PMU controls the power consumption of SATA

NANDrive. The PMU dramatically reduces the power

consumption of SATA NANDrive by putting the part of

the circuitry that is not in operation into sleep mode. 3)

The Flash File System handles inadvertent power

interrupts and has auto-recovery capability to ensure

SATA NANDrive firmware integrity. For regular power

management, the host must send a

STANDBY_IMMEDIATE (E0h), IDLE_IMMEDIATE

(E1h), STANDBY (E2h) or IDLE (E3h) command and

wait for command ready before powering down SATA

NANDrive.

3) For management of the Sleep Mode, refer to “SATA

NANDrive Application Design Guide.”

1.1.4 Embedded Flash File System

The embedded flash file system is an integral part of

SATA NANDrive. It contains MCU firmware that

performs the following tasks:

1. Translates host side signals into flash media

writes and reads

2. Provides flash media wear leveling to spread the

flash writes across all memory address space to

increase the longevity of flash media

3. Keeps track of data file structures

4. Manages system security for the selected

protection zones

1.1.5 Error Correction Code (ECC)

High performance is achieved through optimized

hardware error detection and correction.

1.1.6 Serial Communication Interface (SCI)

The Serial Communication Interface (SCI) is designed

for error reporting. During the product development

stage, it is recommended to provide the SCI port on

the PCB to aid in design validation.

1.1.7 Multi-tasking Interface

The multi-tasking interface enables fast, sequential

write performance by allowing concurrent Read,

Program and Erase operations to multiple flash media.

1.2 SMT Reflow Consideration

The SATA NANDrive family utilizes standard NAND

flash for data storage. Because the high temperature

in a surface-mount soldering reflow process may alter

the content on NAND flash, it is recommended to

program SATA NANDrive after the reflow process.

1.3 Advanced NAND Management

SATA NANDrive’s integrated controller uses

advanced wear-leveling algorithms to substantially

increase the longevity of NAND flash media. Wear

caused by data writes is evenly distributed in all or

select blocks in the device that prevents “hot spots” in

locations that are programmed and erased extensively.

This effective wear-leveling technique results in

optimized device endurance, enhanced data retention

and higher reliability required by long-life applications.

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

2.0 FUNCTIONAL BLOCKS

Figure 2-1: SATA NANDrive Block Diagram

Flash Media I/F

NAND I/F

NAND

Chips

NAND

Chips

NAND

Chips

Embedded Flash

File System

MCU

SATA I/F

Internal

DMA

SCI

PMU

Memory

Channel I/F

NAND Controller

ECC

SRAM Buffer

SATA ll

HOST I/F

3.0/1.5 Gbps

Memory

Channel I/F

ECC

NAND

Chips

NAND

Flash

SATA NANDrive

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

3.0 PRODUCT ORDERING INFORMATION

GLS 85 LS 1 0xxB - M - C - FZJE - NDxxx

XX XX X XXXX - X - X - XXXX - XXXXX

Ordering Code 4)

NDxxx = NANDrive Revision

EDxxx = Evaluation Board Revision

Environmental Attribute

E = non-Pb solder (RoHS Compliant)

Package Modifier

ZJ = 145-ball positions

Package Type

F = FBGA

Operation Temperature

I = Industrial: -40°C to +85°C

C = Commercial: 0°C to +70°C

NAND Configuration

M = 2 bits per cell

Generation / Product Configuration

A = First generation

B = Second generation

Capacity

002 = 2 GByte

004 = 4 GByte

008 = 8 GByte

016 = 16 GByte

032 = 32 GByte

064 = 64 GByte

MByte or GByte Designator

0 = MByte

1 = GByte

Interface

S = SATA

Voltage

L = 3.3V

Product Series

85 = NANDrive

4) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC

(custom specification) which is required by the end-customer to be marked on the device.

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

Valid Combinations

Valid product combinations are those that are in the mass production or will be in the mass production. Consult

your Greenliant sales representative to confirm availability of the valid combinations and to determine availability

of new product combinations.

Table 3-1: SATA NANDrive Product Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Package

2GB

Commercial (0°C to 70°C)

GLS85LS1002A-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1002A-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

4GB

Commercial (0°C to 70°C)

GLS85LS1004A-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1004A-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

8GB

Commercial (0°C to 70°C)

GLS85LS1008B-M-C-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1008B-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1008B-M-I-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1008B-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

16GB

Commercial (0°C to 70°C)

GLS85LS1016B-M-C-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1016B-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1016B-M-I-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1016B-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

32GB

Commercial (0°C to 70°C)

GLS85LS1032B-M-C-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1032B-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1032B-M-I-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1032B-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

64GB

Commercial (0°C to 70°C)

GLS85LS1064B-M-C-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1064B-M-C-FZJE-ND103

FZJE, 14x24x1.95mm

Industrial (-40°C to 85°C)

GLS85LS1064B-M-I-FZJE-ND102

FZJE, 14x24x1.95mm

GLS85LS1064B-M-I-FZJE-ND103

FZJE, 14x24x1.95mm

Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Industrial (-40°C to 85°C)

GLS85LS1002A-M-I-1S-ED103

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004A-M-I-1S-ED103

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008B-M-I-1S-ED102

Module with SATA connector

Industrial (-40°C to 85°C)

GLS85LS1008B-M-I-1S-ED103

Module with SATA connector

16GB

Industrial (-40°C to 85°C)

GLS85LS1016B-M-I-1S-ED102

Module with SATA connector

Industrial (-40°C to 85°C)

GLS85LS1016B-M-I-1S-ED103

Module with SATA connector

32GB

Industrial (-40°C to 85°C)

GLS85LS1032B-M-I-1S-ED102

Module with SATA connector

Industrial (-40°C to 85°C)

GLS85LS1032B-M-I-1S-ED103

Module with SATA connector

64GB

Industrial (-40°C to 85°C)

GLS85LS1064B-M-I-1S-ED102

Module with SATA connector

Industrial (-40°C to 85°C)

GLS85LS1064B-M-I-1S-ED103

Module with SATA connector

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

Table 3-3: SATA NANDrive miniSATA Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Industrial (-40°C to 85°C)

GLS85LS1002A-M-I-1MS-ED103

JEDEC MO-300

4GB

Industrial (-40°C to 85°C)

GLS85LS1004A-M-I-1MS-ED103

JEDEC MO-300

8GB

Industrial (-40°C to 85°C)

GLS85LS1008B-M-I-1MS-ED102

JEDEC MO-300

Industrial (-40°C to 85°C)

GLS85LS1008B-M-I-1MS-ED103

JEDEC MO-300

16GB

Industrial (-40°C to 85°C)

GLS85LS1016B-M-I-1MS-ED102

JEDEC MO-300

Industrial (-40°C to 85°C)

GLS85LS1016B-M-I-1MS-ED103

JEDEC MO-300

32GB

Industrial (-40°C to 85°C)

GLS85LS1032B-M-I-1MS-ED102

JEDEC MO-300

Industrial (-40°C to 85°C)

GLS85LS1032B-M-I-1MS-ED103

JEDEC MO-300

64GB

Industrial (-40°C to 85°C)

GLS85LS1064B-M-I-1MS-ED102

JEDEC MO-300

Industrial (-40°C to 85°C)

GLS85LS1064B-M-I-1MS-ED103

JEDEC MO-300

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

3.1 Package Diagram

TOP VIEW

11

10

9

8

7

6

5

4

3

2

1

A B C D E F G H J K L M N P R T U V W Y AA AB AC

24.0 ±0.1

BOTTOM VIEW

1

2

3

4

5

6

7

8

9

10

11

A B C D E F G H J K L M N P R T U V W Y AA AB AC

SIDE

VIEW

1mm

DETAIL

Note: All linear dimensions are in millimeters.

Untoleranced dimensions are nominal target values.

Coplanarity: 0.15 mm.

0.40 ±0.05 Ball opening size is 0.40 mm (± 0.05 mm).

1.80 ± 0.15

SEATING

PLANE

Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: FZJ

14.0

+/- 0.1

A1

CORNER

14.0

1.0

8.0

1.0

0.5 +/- 0.05

(145x)

0.15

3.0

Fact Sheet 03.001

May 2014

These specifications are subject to change without notice. 05/09/2014

GLS85LS1002A/1004A/1008B/1016B/1032B/1064B

Industrial / Commercial Temp SATA NANDrive™

Revision History

Revision

Description

Date

01.000

Initial release of Fact Sheet

April 5, 2012

01.001

Updated Section 1.2

April 26, 2012

01.002

Updated Ordering Information in Section 4.0

Updated IO type of SCICLK in Table 3-1

August 16, 2012

02.000

Updated Valid Combinations in Section 4.0

October 25, 2012

02.001

Updated Ordering Information in Section 4.0

November 21, 2012

02.002

Placed Valid Combinations into table format in Section 4.0

February 25, 2013

02.003

Removed Table 3-1

April 17, 2013

02.100

Removed Pin Assignments and Updated section numbering; Added

product revision CB2 (ordering code ND103 and ED103) in Section 3.0

August 21, 2013

03.000

Updated Power Specifications section on first page

Added GLS85LS1002A / GLS85LS1004A (rev. CB2)

October 16, 2013

03.001

Updated Section 1.1.3

May 09, 2014

Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant

Systems. All other trademarks and registered trademarks are the property of their respective owners.

Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable

capacity may be less.

Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant

Terms and Conditions of Sale.

www.greenliant.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Greenliant:

GLS85LS1008B-M-I-1MS-ED102 GLS85LS1008B-M-I-1S-ED102 GLS85LS1016B-M-I-1MS-ED102 GLS85LS1016B-

M-I-1S-ED102 GLS85LS1032B-M-I-1MS-ED102 GLS85LS1032B-M-I-1S-ED102 GLS85LS1064B-M-I-1MS-ED102

GLS85LS1064B-M-I-1S-ED102 GLS85LS1064B-M-C-FZJE-ND103 GLS85LS1032B-M-I-1S-ED103 GLS85LS1008B-

M-I-FZJE-ND103 GLS85LS1032B-M-I-FZJE-ND103 GLS85LS1002A-M-C-FZJE-ND103 GLS85LS1004A-M-I-1MS-

ED103 GLS85LS1064B-M-I-1S-ED103 GLS85LS1008B-M-C-FZJE-ND103 GLS85LS1008B-M-I-1S-ED103

GLS85LS1002A-M-I-FZJE-ND103 GLS85LS1064B-M-I-FZJE-ND103 GLS85LS1064B-M-I-1MS-ED103

GLS85LS1016B-M-I-1MS-ED103 GLS85LS1032B-M-I-1MS-ED103 GLS85LS1004A-M-C-FZJE-ND103

GLS85LS1002A-M-I-1MS-ED103 GLS85LS1008B-M-I-1MS-ED103 GLS85LS1016B-M-I-FZJE-ND103

GLS85LS1032B-M-C-FZJE-ND103 GLS85LS1004A-M-I-1S-ED103 GLS85LS1016B-M-I-1S-ED103 GLS85LS1016B-

M-C-FZJE-ND103 GLS85LS1002A-M-I-1S-ED103 GLS85LS1004A-M-I-FZJE-ND103 GLS85LS1064B-M-I-1S-ED100

GLS85LS1064B-M-C-1S-ED100 GLS85LS1064B-M-I-FZJE-ND100 GLS85LS1032B-M-I-1S-ED100 GLS85LS1032B-

M-I-FZJE-ND100 GLS85LS1032B-M-C-1S-ED100 GLS85LS1064B-M-I-1MS-ED100 GLS85LS1032B-M-I-1MS-ED100

GLS85LS1032B-M-C-FZJE-ND100 GLS85LS1064B-M-C-FZJE-ND100 GLS85LS1064B-M-C-1MS-ED100