H2F-DC-AC200/220/240 - Omron

24-hour/Weekly Time Switch H2F

Up to 96 ON/OFF Cycles from DIN-sized

(72 x 72 mm) Timer

Easy setting with color-coded programming tabs.

Choose 24-hour or 1-week models with either

SPST-NO or SPDT control outputs.

Minute dial assures accurate settings.

Models with memory protection available.

Control outputs can be manually turned ON/OFF.

Designed for surface, flush, or track mounting.

Ordering Information

Mounting

method

Control output

24-hour operation

1-week operation

Synchronous motor

Quartz motor (with

memory protection)

Quartz motor (with

memory protection)

Flush SPST-NO H2F-D H2F-DM H2F-WM

SPDT H2F-DC H2F-DMC H2F-WMC

Surface/track SPST-NO H2F-DF H2F-DMF H2F-WMF

SPDT H2F-DFC H2F-DMFC H2F-WMFC

Accessories (Order Separately)

Extra

programming tabs

1 pair for each ON/OFF (see note)

Y92S-21

Rechargeable Battery

Y92S-22

Note:

24-hour type is supplied with three pairs of programming tabs.

1-week type is supplied with seven pairs of programming tabs.

Specifications

Time Ranges

Operation

period

Minimum division Minimum set time

Maximum set time

24-hour

15 min 30 min

23 hrs 45 min

1-week

1 hr

2 hrs

166 hrs

ON/OFF Cycle

Operation

period

24-hour 1-week

Maximum cycles

96 84

Ratings

Rated

supply voltage

Synchronous motor: 100/1

10/120 V

AC, 200/220/240 V

AC (50/60 Hz) (see note)

Quartz motor: 100 to 240 V

AC (50/60 Hz)

Operating voltage range

85% to 1

10% of rated supply voltage

Power consumption

Synchronous motor: 3 V

A max.

Quartz motor: 1 V

A max. at 100 to 120 V

AC, 4 V

A max. at 200 to 240 V

Control outputs

15 A at 250 V

AC, resistive load, SPST-NO, SPDT

Note:

Refer to

Precautions

H2F H2F

Characteristics

Item 24-hour

operation 1-week operation

Synchronous motor

Quartz motor

Accuracy of operating time (see note 1)

3 min max.

30 min max.

Influence of voltage

30 min max.

Influence of temperature

30 min max.

Setting error (see note 2)

3 min max.

30 min max.

Cyclic error

3 min max.

30 min max.

Memory protection against power

failure ---

180 hrs min. (see note 3)

Insulation resistance

100 M

Ω

min. (at 500 VDC)

Dielectric strength

2,000 V

AC, 50/60 Hz for 1 min (between current-carrying terminals and

non-current-carrying metal parts)

1,000 V

AC, 50/60 Hz for 1 min (between non-continuous contacts)

ibration resistance

Destruction:

16.7 Hz, 4-mm double amplitude

Malfunction:

10 to 55 Hz, 0.5-mm double amplitude

Shock resistance

Destruction:

1,000 m/s

(approx. 100G)

Malfunction:

200 m/s

(approx. 20G)

Ambient temperature

Operating: –10

C to 55

°C

Ambient humidity

Operating: 35% to 85%

Life expectancy

2 years min. (approx. 10,000 operations min.)

Approved standards

UL (File No. E52800), CSA (File No. LR22310)

Weight

Flush mounting: approx. 150 g

Surface mounting: approx. 200 g

Note: 1.

Accuracy of operating time of when the timer is ON or when the timer is OFF

2. Dif

ference between the set and actual operation time with the pointer set to the present time.

When the timer is used for the first time after energization of 72 hrs.

H2F H2F

Dimensions

Note:

All units are in millimeters unless otherwise indicated.

Mounting Dimensions

Surface Mounting: H2F-DF/-DMF/-WMF

Track Mounting: H2F-DFC/-DMFC/-WMFC

Mounting

Holes

Two, M3 holes

M3.5

Screw size

M3 x 45

(included)

Flush Mounting: H2F-D/-DM/-WM/-DC/-DMC/-WMC

Panel Cutout

Recommended panel thickness: 3.2 mm

Note: The

mounting adapter and

screws

are included.

65.5

H2F H2F

Installation

Connections

Synchronous Motor Model

(SPST-NO Output)

H2F-D

(SPDT Output)

H2F-DC

H2F-DF H2F-DFC

Quartz Motor Model

(SPST-NO Output)

H2F-DM/H2F-WM

(SPDT Output)

H2F-DMC/WMC

H2F-DMF/H2F-WMF H2F-DMFC/WMFC

Note: Connect

an independent power source to the load.

H2F H2F

Precautions

Flush Mounting

1. To

mount the adapter to the panel cutout, first deform the adapter

by pushing it on the two opposing corners (as indicated by ar-

rows

A. Then

push part B into the cutout (i.e., toward the back of

the

panel).

Panel

Adapter

2. After

the adapter is mounted, insert the timer as shown in the fig

ure below. Secure the timer by tightening the two mounting

screws (M3 x 45) included as accessories.

3. If

the lead wires have been connected to the timer from the

front

the panel before the timer is mounted in the panel, engage the

timer to part A of the adapter and push it in the direction of B.

Then

tighten the two screws as described in 2.

Panel

Lead wire

Time Setting

set the time, turn the center knob clockwise to the correct time.

Turning

counterclockwise or turning it with your fingers hooked on

the

setting bracket may cause a malfunction.

Set

the hour to the arrow on the upper left corner of the front panel

and

the minute, to the arrow on the center knob.

Use

the gold setting tabs to set

the ON time and the silver ones to set

the

OFF time. Position the thick leg of the tab toward the outside of

the

dial and insert the tab securely into the groove on the dial.

Three pairs pairs of setting tabs are attached.

Store

the

spare tabs in the compartment at the lower right corner of

the

front panel.

H2F H2F

Manual Switch

SPST-NO Output

A 3-position selector switch, located at the lower left corner of the

front panel, determines output operation. In the OFF position, the

control

output is forcibly turned OFF regardless of the setting of the

programming tabs. Set to the AUTO position, the output is turned

and OFF according to the settings of the programing tabs. In the

position, the output is forcibly turned ON regardless

of the set

ting

of the programming tabs.

SPDT Output

When

the manual switch

at the lower left corner of the front is set to

the OFF position, both load 1 (connected across terminals 4 and 5)

and

load 2 (across 5 and 6) are turned OFF

When

it is set to the AUT

O position, the output is turned ON and OFF

according

to the setting of the programming tabs.

When

the manual switch is set to the ON position,

load 1 (connected

across terminals 4 and 5) is turned ON and load 2 (across

and 6) is

turned OFF.

Output Indicator

The

output indicator at the upper

left corner of the front panel shows

the

status of the output when the manual switch is set to the AUT

position.

In addition, the output can be manually turned ON or OFF by rotat

ing

the knob clockwise (in the arrow direction). The knob

will not turn

counterclockwise.

Note on H2F-D, -DF Series (synchronous motor versions)

Before

using

the timer

, select the appropriate frequency of your area

the frequency selector switch provided on

the upper part of the

rear panel.

Upper part of rear panel

(cycles per second)

H2F-jM Series (Quartz Motor Models)

Battery

Remove

the battery cover on the rear panel of the H2F

, load the pro

vided

Battery into the battery box, then turn ON the H2F

. Be sure to

load the Battery before using the

H2F

. If the Battery is not loaded,

the power indicator will flash and the H2F will not work properly

Press down.

Battery cover

Slide out

sure to load the Battery with the correct polarity

. The polarity is

indicated in the battery box. After loading the Battery, be sure to

place

the cover on the battery box.

Battery

The

Battery is fully charged before shipment. The Battery may

lose

its

charge while the Battery is stored. Therefore, there is a backup

function

that is guaranteed for 180 hours on condition

that the Bat

tery

loaded into the H2F and charged continuously for 72 hours. If

the Battery has no charge, the H2F may not operate immediately

after it is turned ON. In that case, continue providing power to the

H2F

for three or more minutes before setting the time.

the H2F is turned ON and OFF frequently

, the Battery

life will be

greatly

reduced. Use the H2F with a continuous supply of power

The Battery has a life of approximately three years. If three years

have passed

since the Battery was loaded, replace the Battery as

soon as possible with a AAAA-size NiCd rechargeable battery

the H2F is idle over a long time, unload the Battery from the H2F

and

store the Battery separately in order

to prevent the Battery from

being

overly discharged.

H2F H2F

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

convert millimeters into inches, multiply by 0.03937. T

o convert grams into ounces, multiply by 0.03527.

Cat. No. L013-E1-3A In the interest of product improvement, specifications are subject to change without notice.

Printed

in Japan

1298-0.5C (0696)

OMRON Corporation

Supervisory Control Devices Division

28th Fl., Crystal T

ower Bldg.,

1-2-27, Shiromi, Chuo-ku,

Osaka 540-6028 Japan

Phone: (81)6-949-6035 Fax: (81)6-949-6069