LTC2152-14/ LTC2151-14/LTC2150-14 14-Bit 250Msps/ 210Msps/170Msps ADCs Features n n n n n n n n n n n n Description 70dB SNR 90dB SFDR Low Power: 356mW/338mW/313mW Total Single 1.8V Supply DDR LVDS Outputs Easy-to-Drive 1.5VP-P Input Range 1.25GHz Full Power Bandwidth S/H Optional Clock Duty Cycle Stabilizer Low Power Sleep and Nap Modes Serial SPI Port for Configuration Pin Compatible 12-Bit Versions 40-Pin (6mm x 6mm) QFN Package The LTC(R)2152-14/LTC2151-14/LTC2150-14 are 250Msps/ 210Msps/170Msps 14-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. They are perfect for demanding communications applications with AC performance that includes 70dB SNR and 90dB spurious free dynamic range (SFDR). The 1.25GHz input bandwidth allows the ADC to undersample high frequencies with good performance. The latency is only five clock cycles. DC specs include 0.85LSB INL (typ), 0.25LSB DNL (typ) and no missing codes over temperature. The transition noise is 1.82LSBRMS. Applications n n n n n n The digital outputs are double-data rate (DDR) LVDS. The ENC+ and ENC- inputs can be driven differentially with a sine wave, PECL, LVDS, TTL, or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles. Communications Cellular Basestations Software Defined Radios Medical Imaging High Definition Video Testing and Measurement Instruments L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application LTC2152-14: 32K Point FFT, fIN = 15MHz, -1dBFS, 250Msps VDD 0 OVDD CLOCK S/H CORRECTION LOGIC OUTPUT DRIVERS D12_13 * * * D0_1 OGND CLOCK/DUTY CYCLE CONTROL -20 DDR LVDS AMPLITUDE (dBFS) ANALOG INPUT 14-BIT PIPELINED ADC -40 -60 -80 -100 21521014 TA01a -120 0 20 40 60 80 100 FREQUENCY (MHz) 120 21521014 TA01b 21521014f 1 LTC2152-14/ LTC2151-14/LTC2150-14 Absolute Maximum Ratings Pin Configuration (Notes 1, 2) D10_11- D10_11+ D12_13- D12_13+ GND SDO SDI SCK CS PAR/SER TOP VIEW 40 39 38 37 36 35 34 33 32 31 VDD 1 30 OVDD VDD 2 29 D8_9+ GND 3 28 D8_9- AIN+ 4 27 CLKOUT+ AIN- 5 26 CLKOUT - GND 41 GND 6 25 D6_7+ SENSE 7 24 D6_7- VREF 8 23 D4_5+ VCM 9 22 D4_5- GND 10 21 OGND OVDD D2_3+ D2_3- D0_1+ D0_1- OF + OF - GND ENC- 11 12 13 14 15 16 17 18 19 20 ENC+ Supply Voltage VDD, OVDD................................................. -0.3V to 2V Analog Input Voltage AIN+, AIN -, PAR/SER, SENSE (Note 3)......................... -0.3V to (VDD + 0.2V) Digital Input Voltage ENC+, ENC- (Note 3)................. -0.3V to (VDD + 0.3V) CS, SDI, SCK (Note 4)............................ -0.3V to 3.9V SDO (Note 4).............................................. -0.3V to 3.9V Digital Output Voltage................. -0.3V to (OVDD + 0.3V) Operating Temperature Range LTC2152C, LTC2151C, LTC2150C.............. 0C to 70C LTC2152I, LTC2151I, LTC2150I............. -40C to 85C Storage Temperature Range................... -65C to 150C UJ PACKAGE 40-LEAD (6mm x 6mm) PLASTIC QFN TJMAX = 150C, JA = 34.1C/W EXPOSED PAD (PIN 41) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2152CUJ-14#PBF LTC2152CUJ-14#TRPBF LTC2152UJ-14 40-Lead (6mm x 6mm) Plastic QFN 0C to 70C LTC2152IUJ-14#PBF LTC2152IUJ-14#TRPBF LTC2152UJ-14 40-Lead (6mm x 6mm) Plastic QFN -40C to 85C LTC2151CUJ-14#PBF LTC2151CUJ-14#TRPBF LTC2151UJ-14 40-Lead (6mm x 6mm) Plastic QFN 0C to 70C LTC2151IUJ-14#PBF LTC2151IUJ-14#TRPBF LTC2151UJ-14 40-Lead (6mm x 6mm) Plastic QFN -40C to 85C LTC2150CUJ-14#PBF LTC2150CUJ-14#TRPBF LTC2150UJ-14 40-Lead (6mm x 6mm) Plastic QFN 0C to 70C LTC2150IUJ-14#PBF LTC2150IUJ-14#TRPBF LTC2150UJ-14 40-Lead (6mm x 6mm) Plastic QFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 21521014f 2 LTC2152-14/ LTC2151-14/LTC2150-14 Converter Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) PARAMETER CONDITIONS MIN Resolution (No Missing Codes) l LTC2152-14 TYP MAX MIN 14 LTC2151-14 TYP MAX LTC2150-14 MIN TYP MAX 14 UNITS 14 Bits Integral Linearity Error Differential Analog Input (Note 6) l -5.5 0.85 5.5 -5.1 1 5.1 -5.1 1 5.1 LSB Differential Linearity Error Differential Analog Input l -0.9 0.25 0.9 -0.9 0.25 0.9 -0.9 0.25 0.9 LSB Offset Error (Note 7) l -13 5 13 -13 5 13 -13 3 13 mV Gain Error External Reference l -4 1 3 -4 1 3 -4 1 3 %FS Offset Drift 20 20 20 V/C Full-Scale Drift Internal Reference External Reference 30 10 30 10 30 10 ppm/C ppm/C Transition Noise External Reference 1.82 1.82 1.82 LSBRMS Analog Input The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER VIN Analog Input Range (AIN+ - AIN-) CONDITIONS MIN TYP MAX UNITS 1.7V < VDD < 1.9V l 1.5 VIN(CM) Analog Input Common Mode (AIN+ + AIN-)/2 VP-P Differential Analog Input (Note 8) l VCM - 20mV VCM VCM + 20mV V VSENSE External Reference Mode External Reference Mode l 1.200 1.250 1.300 V IIN1 Analog Input Leakage Current 0 < AIN+, AIN- < VDD No Encode l -1 1 A IIN2 SENSE Input Leakage Current 1.2V < SENSE < 1.3V l -1 1 A IIN3 PAR/SER Input Leakage Current 0 < PAR/SER < VDD l -1 1 A tAP Sample-and-Hold Acquisition Delay Time 1 tJITTER Sample-and-Hold Acquisition Delay Jitter 0.15 CMRR Analog Input Common Mode Rejection Ratio BW-3B Full-Power Bandwidth ns psRMS 75 dB 1250 MHz Dynamic Accuracy The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. AIN = -1dBFS. (Note 5) SYMBOL PARAMETER CONDITIONS SNR Signal-to-Noise Ratio 15MHz Input 70MHz Input 140MHz Input SFDR Spurious Free Dynamic Range 15MHz Input 2nd or 3rd Harmonic 70MHz Input 140MHz Input Spurious Free Dynamic Range 15MHz Input 4th Harmonic or Higher 70MHz Input 140MHz Input S/(N+D) Cross Talk Signal-to-Noise Plus Distortion Ratio 15MHz Input 70MHz Input 140MHz Input Cross-Talk Between Channels Up to 315MHz Input MIN l l l l LTC2152-14 TYP MAX 67.3 70 69.7 69.3 72 90 85 82 81 95 95 85 66.7 69.9 69.4 68.8 -95 MIN LTC2151-14 TYP MAX 67.4 70 69.8 69.4 75 90 85 82 82 95 95 88 66.8 69.9 69.4 68.8 -95 LTC2150-14 MIN TYP MAX UNITS 67.5 70 69.8 69.5 dBFS dBFS dBFS 76 90 85 83 dBFS dBFS dBFS 83 98 95 88 dBFS dBFS dBFS 66.9 69.9 69.4 68.8 dBFS dBFS dBFS -95 dB 21521014f 3 LTC2152-14/ LTC2151-14/LTC2150-14 Internal Reference Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) PARAMETER CONDITIONS VCM Output Voltage IOUT = 0 MIN TYP MAX 0.439 * VDD - 18mV 0.439 * VDD 0.439 * VDD + 18mV VCM Output Temperature Drift UNITS V 37 VCM Output Resistance -1mA < IOUT < 1mA VREF Output Voltage IOUT = 0 ppm/C 4 1.225 1.250 VREF Output Temperature Drift 1.275 V 30 VREF Output Resistance -400A < IOUT < 1mA VREF Line Regulation 1.7V < VDD < 1.9V ppm/C 7 0.6 mV/V Power Requirements The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER CONDITIONS MIN VDD Analog Supply Voltage (Note 9) l 1.7 OVDD Output Supply Voltage LVDS Mode (Note 9) l 1.7 IVDD Analog Supply Current IOVDD Digital Supply Current PDISS Power Dissipation LTC2152-14 TYP MAX 1.8 MIN 1.9 1.7 1.7 LTC2151-14 TYP MAX 1.8 LTC2150-14 MIN TYP MAX 1.9 1.7 1.7 1.8 UNITS 1.9 V 1.8 1.9 1.8 1.9 1.8 1.9 V l 169 186 160 176 147 162 mA 1.75mA LVDS Mode 3.5mA LVDS Mode l 29 49 34.5 54.5 28 48 33.5 54 27 47 32.5 52 mA mA 1.75mA LVDS Mode 3.5mA LVDS Mode l 356 392 397 433 338 374 377 414 313 349 350 385 mW mW PSLEEP Nap Mode Power Clocked at fS(MAX) 105 98 93 mW PNAP Sleep Mode Power Clocked at fS(MAX) <2 <2 <2 mW Digital Inputs And Outputs The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 1 1.9 V 1.5 V V 1.9 V ENCODE INPUTS (ENC+, ENC-) VID Differential Input Voltage (Note 8) l 0.2 VICM Common Mode Input Voltage Internally Set Externally Set (Note 8) l 1.1 l 0.2 1.2 VIN Input Voltage Range ENC+, ENC- to GND RIN Input Resistance (See Figure 2) 10 k CIN Input Capacitance (Note 8) 2 pF DIGITAL INPUTS (CS, SDI, SCK) VIH High Level Input Voltage VDD = 1.8V l VIL Low Level Input Voltage VDD = 1.8V l IIN Input Current VIN = 0V to 1.8V l CIN Input Capacitance (Note 8) 1.3 V -10 0.6 V 10 A 3 pF SDO OUTPUT (Open-Drain Output. Requires 2k Pull-Up Resistor if SDO Is Used) ROL Logic Low Output Resistance to GND VDD = 1.8V, SDO = 0V IOH Logic High Output Leakage Current SDO = 0V to 3.6V COUT Output Capacitance (Note 8) 200 l -10 10 4 A pF 21521014f 4 LTC2152-14/ LTC2151-14/LTC2150-14 DIGITAL INPUTS AND OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER DIGITAL DATA OUTPUTS CONDITIONS VOD Differential Output Voltage VOS Common Mode Output Voltage RTERM On-Chip Termination Resistance 100 Differential Load, 3.5mA Mode 100 Differential Load, 1.75mA Mode 100 Differential Load, 3.5mA Mode 100 Differential Load, 1.75mA Mode Termination Enabled, OVDD = 1.8V l l l l MIN TYP MAX UNITS 247 125 1.125 1.125 350 175 1.250 1.250 100 454 250 1.375 1.375 mV mV V V Timing Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL fS tL PARAMETER Sampling Frequency ENC Low Time (Note 8) tH ENC High Time (Note 8) SYMBOL PARAMETER DIGITAL DATA OUTPUTS CONDITIONS (Note 9) Duty Cycle Stabilizer Off Duty Cycle Stabilizer On Duty Cycle Stabilizer Off Duty Cycle Stabilizer On l l l l l MIN 10 1.9 1.5 1.9 1.5 LTC2152-14 TYP MAX 250 2 50 2 50 2 50 2 50 MIN 10 2.26 1.5 2.26 1.5 CONDITIONS LTC2151-14 TYP MAX 210 2.38 50 2.38 50 2.38 50 2.38 50 LTC2150-14 MIN TYP MAX 10 170 2.79 2.94 50 1.5 2.94 50 2.79 2.94 50 1.5 2.94 50 MIN TYP MAX 2.3 UNITS MHz ns ns ns ns UNITS tD ENC to Data Delay CL = 5pF (Note 8) l 1.7 2 tC ENC to CLKOUT Delay CL = 5pF (Note 8) l 1.3 1.6 2 ns tSKEW DATA to CLKOUT Skew tD - tC (Note 8) l 0.3 0.4 0.55 ns Pipeline Latency 5 5 ns Cycles SPI Port Timing (Note 8) tSCK SCK Period tS CS to SCK Set-Up Time tH Write Mode, CSDO = 20pF Readback Mode RPULLUP = 2k, CSDO = 20pF l 40 250 5 ns ns ns SCK to CS Hold Time l 5 ns tDS SDI Set-Up Time l 5 ns tDH SDI Hold Time l 5 ns tDO SCK Falling to SDO Valid Readback Mode RPULLUP = 2k, CSDO = 20pF Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to GND with GND and OGND shorted (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: When these pin voltages are taken below GND they will be clamped by internal diodes. When these pin voltages are taken above VDD they will not be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND without latchup. l 125 ns Note 5: VDD = OVDD = 1.8V, fSAMPLE = 250MHz (LTC2152), 210MHz (LTC2151), or 170MHz (LTC2150), LVDS outputs, differential ENC+/ENC- = 2VP-P sine wave, input range = 1.5VP-P with differential drive, unless otherwise noted. Note 6: Integral nonlinearity is defined as the deviation of a code from a best fit straight line to the transfer curve. The deviation is measured from the center of the quantization band. Note 7: Offset error is the offset voltage measured from -0.5LSB when the output code flickers between 00 0000 0000 0000 and 11 1111 1111 1111 in 2's complement output mode. Note 8: Guaranteed by design, not subject to test. Note 9: Recommended operating conditions. 21521014f 5 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2152-14: Integral Nonlinearity (INL) LTC2152-14: Differential Nonlinearity (DNL) LTC2152-14: 32K Point FFT, fIN = 15MHz, -1dBFS, 250Msps 2.0 0 0.4 1.5 -20 0.5 0 -0.5 -1.0 0 -0.2 -40 -60 -80 -100 -1.5 -2.0 0.2 AMPLITUDE (dBFS) DNL ERROR (LSB) INL ERROR (LSB) 1.0 -0.4 0 4096 8192 12288 OUTPUT CODE 0 16383 4096 8192 12288 OUTPUT CODE 16383 -120 0 40 60 80 100 FREQUENCY (MHz) 20 120 21521014 G02 21521014 G01 21521014 G03 LTC2152-14: 32K Point FFT, fIN = 122MHz, -1dBFS, 250Msps LTC2152-14: 32K Point FFT, fIN = 171MHz, -1dBFS, 250Msps 0 0 -20 -20 -20 -40 -60 -80 -40 -60 -80 -100 -100 -120 AMPLITUDE (dBFS) 0 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2152-14: 32K Point FFT, fIN = 70MHz, -1dBFS, 250Msps 0 20 40 60 80 100 FREQUENCY (MHz) 120 -120 0 20 40 60 80 100 FREQUENCY (MHz) -80 120 -120 0 40 60 80 100 FREQUENCY (MHz) 20 21521014 G05 LTC2152-14: 32K Point FFT, fIN = 229MHz, -1dBFS, 250Msps 0 0 -20 -20 -40 -60 -80 -100 120 21521014 G06 LTC2152-14: 32K Point FFT, fIN = 381MHz, -1dBFS, 250Msps AMPLITUDE (dBFS) AMPLITUDE (dBFS) -60 -100 21521014 G04 -120 -40 -40 -60 -80 -100 0 20 40 60 80 100 FREQUENCY (MHz) 120 21521014 G07 -120 0 20 40 60 80 100 FREQUENCY (MHz) 120 21521014 G08 21521014f 6 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2152-14: 32K Point FFT, fIN = 907MHz, -1dBFS, 250Msps LTC2152-14: 32K Point FFT, fIN = 571MHz, -1dBFS, 250MHz 0 0 -20 -20 -20 -40 -60 -80 -40 -60 -80 -100 -100 -120 AMPLITUDE (dBFS) 0 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2152-14: 32K Point FFT, fIN = 421MHz, -1dBFS, 250MHz 0 20 -120 40 60 80 100 120 INPUT FREQUENCY (MHz) 21521014 G09 LTC2152-14: 32K Point 2-Tone FFT, fIN = 70.5MHz and 69.5MHz, 250Msps -40 -60 -80 -100 0 20 100 120 40 60 80 INPUT FREQUENCY (MHz) 21521014 G10 -120 -20 4000 50 3500 45 IOVDD (mA) -60 2000 1500 -80 20 0 8196 40 60 80 100 120 INPUT FREQUENCY (MHz) 21521014 G12 8200 8208 8204 OUTPUT CODE 8212 LVDS CURRENT 1.75mA 8216 15 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G14 LTC2152-14: SFDR vs Input Level, fIN = 70MHz, 1.5V Range, 250Msps 170 120 160 100 150 140 130 120 110 30 215210 G13 LTC2152-14: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS SFDR (dBc AND dBFS) 0 35 20 500 IVDD (mA) -120 LVDS CURRENT 3.5mA 25 1000 -100 40 60 80 100 120 INPUT FREQUENCY (MHz) 21521014 G11 40 2500 COUNT AMPLITUDE (dBFS) 3000 -40 20 LTC2152-14: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2152-14: Shorted Input Histogram 0 0 dBFS 80 dBc 60 40 20 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G15 0 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 0 21521014 G16 21521014f 7 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2152-14: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 250Msps LTC2152-14: SNR vs Input Level, fIN = 70MHz, 1.5V Range, 250Msps 70 90 dBFS 80 70 50 dBc SFDR (dBFS) SNR (dBc AND dBFS) 60 40 30 50 40 30 20 20 10 0 60 10 -60 -50 -40 -30 -20 AMPLITUDE (dBFS) -10 0 0 21521014 G17 21521014 G18 LTC2152-14: SNR vs Input Frequency, -1dBFS, 1.5V Range, 250Msps LTC2152-14: Frequency Response -0.5 75 -1.0 INPUT AMPLITUDE (dBFS) 70 SNR (dBFS) 65 60 55 50 45 40 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 -5.5 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21521014 G19 -6.0 100 1000 INPUT FREQUENCY (MHz) 21521014 G20 21521014f 8 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2151-14: Integral Nonlinearity INL LTC2151-14: Differential Nonlinearity DNL LTC2151-14: 32K Point FFT, fIN = 15MHz, -1dBFS, 210Msps 0 2.0 0.4 1.5 -20 0.5 0 -0.5 -1.0 0 4096 8192 12288 OUTPUT CODE 0 16383 4096 21521014 G21 LTC2151-14: 32K Point FFT, fIN = 71MHz, -1dBFS, 210Msps 0 8192 12288 OUTPUT CODE 16383 -80 -120 -40 -60 -80 40 60 80 FREQUENCY (MHz) 20 100 -60 -80 -40 -60 -80 -100 0 21521014 G24 20 40 60 80 FREQUENCY (MHz) -20 -20 AMPLITUDE (dBFS) 0 -40 -60 -80 -100 100 -120 0 20 21521014 G25 40 60 80 FREQUENCY (MHz) 100 21521014 G26 LTC2151-14: 32K Point FFT, fIN = 379MHz, -1dBFS, 210Msps 0 -120 100 21521014 G23 -20 -40 -120 40 60 80 FREQUENCY (MHz) 0 LTC2151-14: 32K Point FFT, fIN = 227MHz, -1dBFS, 210Msps AMPLITUDE (dBFS) 0 20 LTC2151-14: 32K Point FFT, fIN = 171MHz, -1dBFS, 210Msps LTC2151-14: 32K Point FFT, fIN = 101MHz, -1dBFS, 210Msps -100 -100 0 21521014 G22 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -60 -0.4 -20 -120 -0.2 AMPLITUDE (dBFS) 0 0 -40 -100 -1.5 -2.0 0.2 AMPLITUDE (dBFS) DNL ERROR (LSB) INL ERROR (LSB) 1.0 -40 -60 -80 -100 0 20 40 60 80 FREQUENCY (MHz) 100 21521014 G27 -120 0 20 40 60 80 FREQUENCY (MHz) 100 21521014 G28 21521014f 9 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 -40 -60 -80 -100 -120 0 0 -20 -20 AMPLITUDE (dBFS) 0 LTC2151-14: 32K Point FFT, fIN = 907MHz, -1dBFS, 210Msps LTC2151-14: 32K Point FFT, fIN = 571MHz, -1dBFS, 210Msps LTC2151-14: 32K Point FFT, fIN = 417MHz, -1dBFS, 210Msps -40 -60 -80 -100 0 20 40 60 80 FREQUENCY (MHz) -120 100 -60 -80 -100 0 20 21521014 G29 LTC2151-14: 32K Point 2-Tone FFT, fIN = 70.5MHz and 69.5MHz, 210Msps -40 40 60 80 FREQUENCY (MHz) 100 -120 -20 4000 50 3500 45 IOVDD (mA) -60 2000 1500 -80 -120 20 40 60 80 FREQUENCY (MHz) 0 8196 100 21521014 G32 8200 8208 8204 OUTPUT CODE 8212 LVDS CURRENT 1.75mA 8216 15 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G34 LTC2151-14: SFDR vs Input Level, fIN = 71MHz, 1.5V Range, 210Msps 170 120 160 SFDR (dBc AND dBFS) 100 150 IVDD (mA) 30 215210 G33 LTC2151-14: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS 140 130 120 110 35 20 500 0 21521014 G31 LVDS CURRENT 3.5mA 25 1000 -100 100 40 2500 COUNT AMPLITUDE (dBFS) 3000 -40 40 60 80 FREQUENCY (MHz) 20 LTC2151-14: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2151-14: Shorted Input Histogram 0 0 21521014 G30 dBFS 80 60 dBc 40 20 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G35 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 0 21521014 G36 21521014f 10 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2151-14: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 210Msps LTC2151-14: SNR vs Input Level, fIN = 71MHz, 1.5V Range, 210Msps 70 90 dBFS 80 70 50 dBc SFDR (dBFS) SNR (dBc AND dBFS) 60 40 30 50 40 30 20 20 10 0 60 10 -60 -50 -40 -30 -20 AMPLITUDE (dBFS) -10 0 0 21521014 G37 21521014 G38 LTC2151-14: SNR vs Input Frequency, -1dBFS, 1.5V Range, 210Msps LTC2151-14: Frequency Response -0.5 75 -1.0 70 INPUT AMPLITUDE (dBFS) -1.5 SNR (dBFS) 65 60 55 50 45 40 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 -5.5 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21521014 G39 -6.0 100 1000 INPUT FREQUENCY (MHz) 21521014 G40 21521014f 11 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2150-14: Differential Nonlinearity DNL LTC2150-14: Integral Nonlinearity INL 0 2.0 0.4 1.5 -20 0.5 0 -0.5 -1.0 0.2 AMPLITUDE (dBFS) DNL ERROR (LSB) INL ERROR (LSB) 1.0 0 -0.2 -40 -60 -80 -100 -1.5 -2.0 LTC2150-14: 32K Point FFT, fIN = 15MHz, -1dBFS, 170Msps -0.4 0 4096 8192 12288 OUTPUT CODE 0 0 16383 21521014 G41 4096 8192 12288 OUTPUT CODE LTC2150-14: 32K Point FFT, fIN = 70MHz, -1dBFS, 170Msps 0 -40 -60 -80 -100 -120 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21521014 G43 LTC2150-14: 32K Point FFT, fIN = 121MHz, -1dBFS, 170Msps -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 -120 0 10 20 21521014 G44 0 0 -20 -20 -40 -60 -80 -100 30 40 50 60 FREQUENCY (MHz) 70 80 21521014 G45 LTC2150-14: 32K Point FFT, fIN = 225MHz, -1dBFS, 170Msps AMPLITUDE (dBFS) AMPLITUDE (dBFS) 0 21521014 G42 -40 LTC2150-14: 32K Point FFT, fIN = 176MHz, -1dBFS, 170Msps -120 -120 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 16383 -40 -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21521014 G46 -120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21521014 G47 21521014f 12 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics 0 -60 -80 -100 0 -40 -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 -120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 0 10 20 21521014 G49 30 40 50 60 FREQUENCY (MHz) 70 80 21521014 G50 LTC2150-14: Shorted Input Histogram 0 AMPLITUDE (dBFS) -80 -80 -120 80 4000 3500 -20 -60 -60 LTC2150-14: 32K Point 2-Tone FFT, fIN = 70.5MHz and 69.5MHz, 170Msps LTC2150-14: 32K Point FFT, fIN = 907MHz, -1dBFS, 170Msps -40 -40 -100 21521014 G48 -20 AMPLITUDE (dBFS) -20 AMPLITUDE (dBFS) -40 -120 0 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 LTC2150-14: 32K Point FFT, fIN = 571MHz, -1dBFS, 170Msps LTC2150-14: 32K Point FFT, fIN = 420MHz, -1dBFS, 170Msps 3000 -40 2500 COUNT 0 LTC2150-14: 32K Point FFT, fIN = 380MHz, -1dBFS, 170Msps -60 2000 1500 -80 1000 -100 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 -120 500 0 10 21521014 G51 20 30 40 50 60 70 INPUT FREQUENCY (MHz) 80 0 8196 8200 21521014 G52 8208 8204 OUTPUT CODE 8212 8216 215210 G53 LTC2150-14: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2150-14: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS 50 160 LVDS CURRENT 3.5mA 45 150 40 140 35 30 IVDD (mA) 0 IOVDD (mA) -120 -100 LVDS CURRENT 1.75mA 25 120 20 15 130 110 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G54 0 50 100 150 200 SAMPLE RATE (Msps) 250 21521014 G55 21521014f 13 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Performance Characteristics LTC2150-14: SFDR vs Input Level, fIN = 70MHz, 1.5V Range, 170Msps 70 120 dBFS 80 dBc 40 20 70 50 dBc SFDR (dBFS) 80 60 90 dBFS 60 SNR (dBc AND dBFS) SFDR (dBc AND dBFS) 100 40 30 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 0 0 50 40 20 10 -60 21521014 G56 -50 -40 -30 -20 AMPLITUDE (dBFS) LTC2150-14: SNR vs Input Frequency, -1dBFS, 1.5V Range, 170Msps -10 0 21521014 G57 0 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21521014 G58 LTC2150-14: Frequency Response -0.5 75 -1.0 INPUT AMPLITUDE (-dBFS) 70 65 SNR (dBFS) 60 30 20 10 60 55 50 45 40 LTC2150-14: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 170Msps LTC2150-14: SNR vs Input Level, fIN = 70MHz, 1.5V Range, 170Msps -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 -5.5 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21521014 G59 -6.0 100 1000 INPUT FREQUENCY (MHz) 21521014 G60 21521014f 14 LTC2152-14/ LTC2151-14/LTC2150-14 Pin Functions VDD (Pins 1, 2): 1.8V Analog Power Supply. Bypass to ground with 0.1F ceramic capacitor. Pins 1, 2 can share a bypass capacitor. GND (Pins 3, 6, 10, 13, 35, Exposed Pad Pin 41): ADC Power Ground. The exposed pad must be soldered to the PCB ground. AIN+ (Pin 4): Positive Differential Analog Input. AIN- (Pin 5): Negative Differential Analog Input. SENSE (Pin 7): Reference Programming Pin. Connecting SENSE to VDD selects the internal reference and a 0.75V input range. An external reference between 1.2V and 1.3V applied to SENSE selects an input range of 0.6 x VSENSE. VREF (Pin 8): Reference Voltage Output. Bypass to ground with a 2.2F ceramic capacitor. Nominally 1.25V. VCM (Pin 9): Common Mode Bias Output; nominally equal to 0.439 * VDD. VCM should be used to bias the common mode of the analog inputs. Bypass to ground with a 0.1F ceramic capacitor. ENC+ (Pin 11): Encode Input. Conversion starts on the rising edge. ENC- (Pin 12): Encode Complement Input. Conversion starts on the falling edge. OVDD (Pins 20, 30): 1.8V Output Driver Supply. Bypass to ground with a 0.1F ceramic capacitor. OGND (Pin 21): LVDS Driver Ground. SDO (Pin 36): Serial Interface Data Output. In serial programming mode, (PAR/SER = 0V), SDO is the optional serial interface data output. Data on SDO is read back from the mode control registers and can be latched on the falling edge of SCK. SDO is an open-drain N-channel MOSFET output that requires an external 2k pull-up resistor from 1.8V to 3.3V. If readback from the mode control registers is not needed, the pull-up resistor is not necessary and SDO can be left unconnected. SDI (Pin 37): Serial Interface Data Input. In serial programming mode, (PAR/SER = 0V), SDI is the serial interface data input. Data on SDI is clocked into the mode control registers on the rising edge of SCK. In parallel programming mode (PAR/SER = VDD), SDI selects 3.5mA or 1.75mA LVDS output current (see Table 2). SCK (Pin 38): Serial Interface Clock Input. In serial programming mode, (PAR/SER = 0V), SCK is the serial interface clock input. In parallel programming mode (PAR/ SER = VDD), SCK controls the sleep mode (see Table 2). CS (Pin 39): Serial Interface Chip Select Input. In serial programming mode, (PAR/SER = 0V), CS is the serial interface chip select input. When CS is low, SCK is enabled for shifting data on SDI into the mode control registers. In parallel programming mode (PAR/SER = VDD), CS controls the clock duty cycle stabilizer (see Table 2). PAR/SER (Pin 40): Programming Mode Selection Pin. Connect to ground to enable the serial programming mode. CS, SCK, SDI and SDO become a serial interface that control the A/D operating modes. Connect to VDD to enable the parallel programming mode where CS, SCK and SDI become parallel logic inputs that control a reduced set of the A/D operating modes. PAR/SER should be connected directly to ground or the VDD of the part and not be driven by a logic signal. 21521014f 15 LTC2152-14/ LTC2151-14/LTC2150-14 Pin Functions CLKOUT -/CLKOUT+ (Pins 26/27): Data Output Clock. The digital outputs normally transition at the same time as the falling and rising edges of CLKOUT+. The phase of CLKOUT+ can also be delayed relative to the digital outputs by programming the mode control registers. LVDS Outputs (DDR LVDS) The following pins are differential LVDS outputs. The output current level is programmable. There is an optional internal 100 termination resistor between the pins of each LVDS output pair. OF-/OF+ (Pins 14/15): Over/Underflow Digital Output. OF+ is high when an overflow or underflow has occurred. This underflow is valid only when CLKOUT+ is low. In the second half clock cycle, the overflow is set to 0. D0_1-/D0_1+ to D12_13-/D12_13+ (Pins 16/17, 18/19, 22/23, 24/25, 28/29, 31/32, 33/34): Double-Data Rate Digital Outputs. Two data bits are multiplexed onto each differential output pair. The even data bits (D0, D2, D4, D6, D8, D10, D12) appear when CLKOUT+ is low. The odd data bits (D1, D3, D5, D7, D9, D11, D13) appear when CLKOUT+ is high. Functional Block Diagram VDD OVDD ANALOG INPUT 14-BIT PIPELINED ADC S/H VCM 0.1F CORRECTION LOGIC OUTPUT DRIVERS VCM BUFFER D12_13 * * * D0_1 DDR LVDS OGND BUFFER GND CLOCK CLOCK/DUTY CYCLE CONTROL CS SCK SDI SDO PAR/SER SPI VREF 2.2F 1.25V REFERENCE GND SENSE GND RANGE SELECT 21521014 F01 Figure 1. Functional Block Diagram 21521014f 16 LTC2152-14/ LTC2151-14/LTC2150-14 Timing Diagrams Double-Data Rate Output Timing, All Outputs Are Differential LVDS N tAP N+3 N+2 N+1 tL tH ENC- ENC+ CLKOUT + CLKOUT - D0_1- D0_1+ D12_13- D12_13+ OF - OF + tC D0N-5 D1N-5 D0N-4 D1N-4 D0N-3 D1N-3 D12N-5 D13N-5 D12N-4 D13N-4 D12N-3 D13N-3 OFN-5 INVALID OFN-4 INVALID OFN-3 INVALID tD tSKEW 21521014 TD01 21521014f 17 LTC2152-14/ LTC2151-14/LTC2150-14 Timing Diagrams SPI Port Timing (Readback Mode) tDS tS tDH tSCK tH CS SCK tDO SDI SDO R/W A6 A5 A4 A3 A2 A1 A0 XX D7 HIGH IMPEDANCE XX D6 XX D5 XX D4 XX D3 XX D2 XX XX D1 D0 SPI Port Timing (Write Mode) CS SCK SDI SDO R/W HIGH IMPEDANCE A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 21521014 TD02 21521014f 18 LTC2152-14/ LTC2151-14/LTC2150-14 APPLICATIONS INFORMATION CONVERTER OPERATION INPUT DRIVE CIRCUITS The LTC2152-14/LTC2151-14/LTC2150-14 are 14-bit 250Msps/210Msps/170Msps A/D converters that are powered by a single 1.8V supply. The analog inputs must be driven differentially. The encode inputs should be driven differentially for optimal performance. The digital outputs are double-data rate LVDS. Additional features can be chosen by programming the mode control registers through a serial SPI port. Input Filtering ANALOG INPUT The analog input is a differential CMOS sample-and-hold circuit (Figure 2). It must be driven differentially around a common mode voltage set by the VCM output pin, which is nominally 0.8V. The inputs should swing from VCM - 0.375V to VCM + 0.375V. There should be a 180 phase difference between the inputs. If possible, there should be an RC lowpass filter right at the analog inputs. This lowpass filter isolates the drive circuitry from the A/D sample-and-hold switching, and also limits wide band noise from the drive circuitry. Figure 3 shows an example of an input RC filter. The RC component values should be chosen based on the application's input frequency. Transformer-Coupled Circuits Figure 3 shows the analog input being driven by an RF transformer with the common mode supplied through a pair of resistors via the VCM pin. At higher input frequencies a transmission line balun transformer (Figures 4 and 5) has better balance, resulting in lower A/D distortion. LTC2152-14 VDD AIN+ RON 20 5 10 2pF 0.1F 2pF IN VDD AIN- RON 20 5 VCM 0.1F T1 1:1 4.7 LTC2152-14 AIN+ 25 2pF 0.1F 4.7 25 2pF VDD 10pF AIN- T1: MACOM ETC1-1T 21521014 F03 Figure 3. Analog Input Circuit Using a Transformer. Recommended for Input Frequencies from 5MHz to 70MHz 1.2V 10k ENC+ 10 ENC- 0.1F T1 MABA 007159000000 IN 21521014 F02 Figure 2. Equivalent Input Circuit for Differential Input Clock T2 WBC1-1L 1:1 LTC2152-14 4.7 AIN+ 45 45 0.1F VCM 0.1F 0.1F 4.7 100 AIN- 21521014 F04 Figure 4. Recommended Front-End Circuit for Input Frequencies from 15MHz to 150MHz 21521014f 19 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information Amplifier Circuits VCM LTC2152-14 4.7 MABA 007159000000 IN Figure 6 shows the analog input being driven by a high speed differential amplifier. The output of the amplifier is AC-coupled to the A/D so the amplifier's output common mode voltage can be optimally set to minimize distortion. 0.1F 10 0.1F AIN+ 45 T1 0.1F 100 45 0.1F 4.7 AIN- 21521014 F05 Figure 5. Recommended Front-End Circuit for Input Frequencies from 150MHz Up to 900MHz 50 50 0.1F 0.1F 4.7 INPUT 0.1F 4.7 3pF Reference The LTC2152-14/LTC2151-14/LTC2150-14 has an internal 1.25V voltage reference. For a 1.5V input range with internal reference, connect SENSE to VDD. For a 1.5V input range with an external reference, apply a 1.25V reference voltage to SENSE (Figure 7). VCM LTC2152-14 3pF At very high frequencies an RF gain block will often have lower distortion than a differential amplifier. If the gain block is single-ended, then a transformer circuit (Figures 3 and 5) should convert the signal to differential before driving the A/D. The A/D cannot be driven single-ended. Encode Input The signal quality of the encode inputs strongly affects the A/D noise performance. The encode inputs should be treated as analog signals--do not route them next to digital traces on the circuit board. AIN+ AIN- 3pF 21521014 F06 Figure 6. Front-End Circuit Using a High Speed Differential Amplifier The encode inputs are internally biased to 1.2V through 10k equivalent resistance (Figure 8). If the common mode of the driver is within 1.1V to 1.5V, it is possible to drive LTC2152-14 1.25V 5 VREF 1.2V 2.2F SCALER/ BUFFER SENSE VDD ADC REFERENCE SENSE DETECTOR 10k ENC- 21521014 F07 Figure 7. Reference Circuit ENC+ 21521014 F08 Figure 8. Equivalent Encode Input Circuit 21521014f 20 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information the encode inputs directly. Otherwise, a transformer or coupling capacitors are needed (Figures 9 and 10). The maximum (peak) voltage of the input signal should never exceed VDD +0.1V or go below -0.1V. For applications where the sample rate needs to be changed quickly, the clock duty cycle stabilizer can be disabled. If the duty cycle stabilizer is disabled, care should be taken to make the sampling clock have a 50% (5%) duty cycle. Clock Duty Cycle Stabilizer DIGITAL OUTPUTS For good performance the encode signal should have a 50% (5%) duty cycle. If the optional clock duty cycle stabilizer circuit is enabled, the encode duty cycle can vary from 30% to 70% and the duty cycle stabilizer will maintain a constant 50% internal duty cycle. If the encode signal changes frequency or is turned off, the duty cycle stabilizer circuit requires one hundred clock cycles to lock onto the input clock. The duty cycle stabilizer is enabled via SPI Register A2 (see SPI Control Register) or by CS in parallel programming mode. The digital outputs are double-data rate LVDS signals. Two data bits are multiplexed and output on each differential output pair. There are seven LVDS output pairs (D0_1+/ D0_1- through D12_13-/D12_13+). Overflow (OF+/OF-) and the data output clock (CLKOUT+/CLKOUT-) each have an LVDS output pair. By default the outputs are standard LVDS levels: 3.5mA output current and a 1.25V output common mode voltage. LTC2152-14 VDD 1.2V 0.1F 10k 50 T1 100 0.1F 50 0.1F 21521014 F09 T1: MACOM ETC1-1-13 Figure 9. Sinusoidal Encode Drive LTC2152-14 VDD 1.2V 0.1F PECL OR LVDS INPUT ENC+ 10k 100 0.1F ENC- 21521014 F10 Figure 10. PECL or LVDS Encode Drive 21521014f 21 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information An external 100 differential termination resistor is required for each LVDS output pair. The termination resistors should be located as close as possible to the LVDS receiver. Overflow Bit The outputs are powered by OVDD and OGND, which are isolated from the A/D core power and ground. The overflow output bit (OF) outputs a logic high when the analog input is either overranged or underranged. The overflow bit has the same pipeline latency as the data bits. Programmable LVDS Output Current The OF is valid when CLKOUT+ is low. The default output driver current is 3.5mA. This current can be adjusted by serially programming mode control register A3 (see Table 3). Available current levels are 1.75mA, 2.1mA, 2.5mA, 3mA, 3.5mA, 4mA and 4.5mA. Optional LVDS Driver Internal Termination In most cases, using just an external 100 termination resistor will give excellent LVDS signal integrity. In addition, an optional internal 100 termination resistor can be enabled by serially programming mode control register A3. The internal termination helps absorb any reflections caused by imperfect termination at the receiver. When the internal termination is enabled, the output driver current is doubled to maintain the same output voltage swing. Phase Shifting the Output Clock To allow adequate set-up and hold time when latching the output data, the CLKOUT+ signal may need to be phase shifted relative to the data output bits. Most FPGAs have this feature; this is generally the best place to adjust the timing. Alternatively, the ADC can also phase shift the CLKOUT+/ CLKOUT- signals by serially programming mode control register A2. The output clock can be shifted by 0, 45, 90, or 135. To use the phase shifting feature, the clock duty cycle stabilizer must be turned on. Another control register bit can invert the polarity of CLKOUT+ and CLKOUT-, independently of the phase shift. The combination of these two features enables phase shifts of 45 up to 315 (Figure 11). ENC+ D0-D13, OF CLKOUT+ MODE CONTROL BITS PHASE SHIFT CLKINV CLKPHASE1 CLKPHASE0 0 0 0 0 45 0 0 1 90 0 1 0 135 0 1 1 180 1 0 0 225 1 0 1 270 1 1 0 315 1 1 1 21521014 F11 Figure 11. Phase Shifting CLKOUT 21521014f 22 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information DATA FORMAT CLKOUT Table 1 shows the relationship between the analog input voltage, the digital data output bits and the overflow bit. By default the output data format is offset binary. The 2's complement format can be selected by serially programming mode control register A4. OF OF D13 Table 1. Output Codes vs Input Voltage AIN+ - AIN- CLKOUT D13/D0 D12 (1.5V Range) OF D13-D0 (OFFSET BINARY) D13-D0 (2's COMPLEMENT) >0.75 V 1 11 1111 1111 1111 01 1111 1111 1111 +0.75V 0 11 1111 1111 1111 01 1111 1111 1111 +0.749908V 0 11 1111 1111 1110 01 1111 1111 1110 +0.0000915V 0 10 0000 0000 0001 00 0000 0000 0001 +0.000000V 0 10 0000 0000 0000 00 0000 0000 0000 -0.0000915V 0 01 1111 1111 1111 11 1111 1111 1111 -0.0001831V 0 01 1111 1111 1110 11 1111 1111 1110 -0.7499084V 0 00 0000 0000 0001 10 0000 0000 0001 -0.75V 0 00 0000 0000 0000 10 0000 0000 0000 < -0.75V 1 00 0000 0000 0000 10 0000 0000 0000 Digital Output Randomizer Interference from the A/D digital outputs is sometimes unavoidable. Digital interference may be from capacitive or inductive coupling or coupling through the ground plane. Even a tiny coupling factor can cause unwanted tones in the ADC output spectrum. By randomizing the digital output before it is transmitted off-chip, these unwanted tones can be randomized, which reduces the unwanted tone amplitude. The digital output is randomized by applying an exclusiveOR logic operation between the LSB and all other data output bits. To decode, the reverse operation is applied--an exclusive-OR operation is applied between the LSB and all other bits. The LSB, OF and CLKOUT outputs are not affected. The output randomizer is enabled by serially programming mode control register A4. D12/D0 * * * RANDOMIZER ON D1 D1/D0 D0 D0 21521014 F12 Figure 12. Functional Equivalent of Digital Output Randomizer PC BOARD CLKOUT FPGA OF D13/D0 LTC215X-14 D13 D12/D0 D1/D0 D0 * * * D12 D1 D0 21521014 F13 Figure 13. Unrandomizing for Randomized Digital Output Signal 21521014f 23 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information Alternate Bit Polarity Another feature that may reduce digital feedback on the circuit board is the alternate bit polarity mode. When this mode is enabled, all of the odd bits (D1, D3, D5, D7, D9, D11, D13) are inverted before the output buffers. The even bits (D0, D2, D4, D6, D8, D10, D12), OF and CLKOUT are not affected. This can reduce digital currents in the circuit board ground plane and reduce digital noise, particularly for very small analog input signals. The digital output is decoded at the receiver by inverting the odd bits (D1, D3, D5, D7, D9, D11, D13.) The alternate bit polarity mode is independent of the digital output randomizer--either both or neither function can be on at the same time. The alternate bit polarity mode is enabled by serially programming mode control register A4. Digital Output Test Patterns To allow in-circuit testing of the digital interface to the A/D, there are several test modes (activate by setting DTESTON) that force the A/D data outputs (OF, D13 to D0) to known values: All 1s: All outputs are 1 All 0s: All outputs are 0 Alternating: Outputs change from all 1s to all 0s on alternating samples Checkerboard: Outputs change from 101010101010101 to 010101010101010 on alternating samples. it is not designed for multiplexing the data bus between multiple converters. Sleep Modes The A/D may be placed in a power-down mode to conserve power. In sleep mode, the entire A/D converter is powered down, resulting in < 2mW power consumption. If the encode input signal is not disabled, the power consumption will be higher (up to 2mW at 250Msps). Sleep mode is enabled by mode control register A1 (serial programming mode), or by SCK (parallel programming mode). The amount of time required to recover from sleep mode depends on the size of the bypass capacitors on VREF . For the suggested values in Figure 1, the A/D will stabilize after 0.1ms + 2500 * tp where tp is the period of the sampling clock. Nap Mode In nap mode the A/D core is powered down while the internal reference circuits stay active, allowing faster wakeup. Recovering from nap mode requires at least 100 clock cycles. Wake-up time from nap mode is guaranteed only if the clock is kept running, otherwise power-down wake-up time conditions apply. Nap mode is enabled by power-down register A1 in the serial programming mode. DEVICE PROGRAMMING MODES The digital output test patterns are enabled by serially programming mode control register A4. When enabled, the test patterns override all other formatting modes: 2's complement, randomizer, alternate-bit polarity. The operating modes of the LTC215X-14 can be programmed by either a parallel interface or a simple serial interface. The serial interface has more flexibility and can program all available modes. The parallel interface is more limited and can only program some of the more commonly used modes. Output Disable Parallel Programming Mode The digital outputs may be disabled by serially programming mode control register A3. All digital outputs, including OF and CLKOUT, are disabled. The high impedance disabled state is intended for long periods of inactivity, To use the parallel programming mode, PAR/SER should be tied to VDD. The CS, SCK and SDI pins are binary logic inputs that set certain operating modes. These pins can be tied to VDD or ground, or driven by 1.8V, 2.5V, or 3.3V 21521014f 24 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information CMOS logic. Table 2 shows the modes set by CS, SCK and SDI. Table 2. Parallel Programming Mode Control Bits) PIN DESCRIPTION CS Clock Duty Cycle Stabilizer Control Bit 0 = Clock Duty Cycle Stabilizer Off 1 = Clock Duty Cycle Stabilizer On SCK Power-Down Control Bit 0 = Normal Operation Software Reset If serial programming is used, the mode control registers should be programmed as soon as possible after the power supplies turn on and are stable. The first serial command must be a software reset which will reset all register data bits to logic 0. To perform a software reset it is necessary to write 1 in register A0 (Bit D7). After the reset is complete, Bit D7 is automatically set back to zero. This register is WRITE-ONLY. 1 = Sleep Mode (entire ADC is powered down) SDI LVDS Current Selection Bit 0 = 3.5mA LVDS Current Mode 1 = 1.75mA LVDS Current Mode Serial Programming Mode To use the serial programming mode, PAR/SER should be tied to ground. The CS, SCK, SDI and SDO pins become a serial interface that program the A/D control registers. Data is written to a register with a 16-bit serial word. Data can also be read back from a register to verify its contents. Serial data transfer starts when CS is taken low. The data on the SDI pin is latched at the first sixteen rising edges of SCK. Any SCK rising edges after the first sixteen are ignored. The data transfer ends when CS is taken high again. The first bit of the 16-bit input word is the R/W bit. The next seven bits are the address of the register (A6:A0). The final eight bits are the register data (D7:D0). If the R/W bit is low, the serial data (D7:D0) will be written to the register set by the address bits (A6:A0). If the R/W bit is high, data in the register set by the address bits (A6:A0) will be read back on the SDO pin (see the Timing Diagrams). During a readback command the register is not updated and data on SDI is ignored. The SDO pin is an open-drain output that pulls to ground with a 200 impedance. If register data is read back through SDO, an external 2k pull-up resistor is required. If serial data is only written and readback is not needed, then SDO can be left floating and no pull-up resistor is needed. Table 3 shows a map of the mode control registers. GROUNDING AND BYPASSING The LTC215X-14 requires a printed circuit board with a clean unbroken ground plane in the first layer beneath the ADC. A multilayer board with an internal ground plane is recommended. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track or underneath the ADC. High quality ceramic bypass capacitors should be used at the VDD, OVDD, VCM and VREF pins. Bypass capacitors must be located as close to the pins as possible. Size 0402 ceramic capacitors are recommended. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. The analog inputs, encode signals and digital outputs should not be routed next to each other. Ground fill and grounded vias should be used as barriers to isolate these signals from each other. HEAT TRANSFER Most of the heat generated by the LTC215X-14 is transferred from the die through the bottom-side exposed pad and package leads onto the printed circuit board. For good electrical and thermal performance, the exposed pad must be soldered to a large grounded pad on the PC board. This pad should be connected to the internal ground planes by an array of vias. 21521014f 25 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information Table 3. Serial Programming Mode Register Map (PAR/SER = GND). An "X" indicates an unused bit. REGISTER A0: RESET REGISTER (ADDRESS 00h) WRITE-ONLY D7 D6 D5 D4 D3 D2 D1 D0 RESET X X X X X X X RESET Bit 7 Software Reset Bit 0 = Not Used 1 = Software Reset. All mode control registers are reset to 00h. After the Reset SPI Write Command is Complete, Bit D7 is Automatically Set Back to Zero. The Reset Register is Write Only. Bits 6-0 Unused bit. REGISTER A1: POWER-DOWN REGISTER (ADDRESS 01h) D7 D6 D5 D4 D3 D2 D1 D0 X X X X SLEEP NAP 0 0 Bits 7-4 Unused, these bits are read back as 0. Bit 3 SLEEP 0 = Normal Operation 1 = Power Down Entire ADC Bit 2 NAP 0 = Normal Mode 1 = Low Power Mode Bit 1-0 Must be set to 0. REGISTER A2: TIMING REGISTER (ADDRESS 02h) D7 D6 D5 D4 D3 D2 D1 D0 X X X X CLKINV CLKPHASE1 CLKPHASE0 DCS Bits 7-4 Unused, these bits are read back as 0. Bit 3 CLKINV Output Clock Invert Bit 0 = Normal CLKOUT Polarity (as shown in the Timing Diagrams) 1 = Inverted CLKOUT Polarity Bits 2-1 CLKPHASE1:CLKPHASE0 Output Clock Phase Delay Bits 00 = No CLKOUT Delay (as shown in the Timing Diagrams) 01 = CLKOUT+/CLKOUT- delayed by 45 (Clock Period * 1/8) 10 = CLKOUT+/CLKOUT- delayed by 90 (Clock Period * 1/4) 11 = CLKOUT+/CLKOUT- delayed by 135 (Clock Period * 3/8) Note: If the CLKOUT phase delay feature is used, the clock duty cycle stabilizer must also be turned on. Bit 0 DCS Clock Duty Cycle Stabilizer Bit 0 = Clock Duty Cycle Stabilizer Off 1 = Clock Duty Cycle Stabilizer On 21521014f 26 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information REGISTER A3: OUTPUT MODE REGISTER (ADDRESS 03h) D7 X D6 D5 D4 D3 D2 D1 D0 X X ILVDS2 ILVDS1 ILVDS0 TERMON OUTOFF Bits 7-5 Unused, these bits are read back as 0. Bits 4-2 ILVDS2:ILVDS0 LVDS Output Current Bits 000 = 3.5mA LVDS Output Driver Current 001 = 4.0mA LVDS Output Driver Current 010 = 4.5mA LVDS Output Driver Current 011 = Not Used 100 = 3.0mA LVDS Output Driver Current 101 = 2.5mA LVDS Output Driver Current 110 = 2.1mA LVDS Output Driver Current 111 = 1.75mA LVDS Output Driver Current Bit 1 TERMON LVDS Internal Termination Bit 0 = Internal Termination Off 1 = Internal Termination On. LVDS output driver current is 2x the current set by ILVDS2:ILVDS0 Bit 0 OUTOFF Digital Output Mode Control Bits 0 = LVDS DDR 1 = LVDS Tristate (High Impedance) REGISTER A4: DATA FORMAT REGISTER (ADDRESS 04h) D7 D6 D5 D4 D3 D2 D1 D0 OUTTEST2 OUTTEST1 OUTTEST0 ABP 0 DTESTON RAND TWOSCOMP Bits 7-5 OUTTEST2:OUTTEST0 Digital Output Test Pattern Bits 000 = All Digital Outputs = 0 001 = All Digital Outputs = 1 010 = Alternating Output Pattern. OF, D13-D0 alternate between 000 0000 0000 0000 and 111 1111 1111 1111 100 = Checkerboard Output Pattern. OF, D13-D0 alternate between 010 1010 1010 1010 and 101 0101 0101 0101 Bit 4 ABP Alternate Bit Polarity Mode Control Bit 0 = Alternate Bit Polarity Mode Off 1 = Alternate Bit Polarity Mode On Bit 3 Must be set to 0. Bit 2 DTESTON Enable digital patterns (Bits 7-5) 0 = Normal Mode 1 = Enable the Digital Output Test Patterns Bit 1 RAND Data Output Randomizer Mode Control Bit 0 = Data Output Randomizer Mode Off 1 = Data Output Randomizer Mode On Bit 0 TWOSCOMP Two's Complement Mode Control Bit 0 = Offset Binary Data Format 1 = Two's Complement Data Format 21521014f 27 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information 215210 F14 Silkscreen Top Inner Layer 1 GND 215210 F15 Inner Layer 2 215210 F16 Inner Layer 3 215210 F17 21521014f 28 LTC2152-14/ LTC2151-14/LTC2150-14 Applications Information 215210 F18 Inner Layer 4 215210 F19 Inner Layer 5 215210 F20 Bottom Layer 6 21521014f 29 LTC2152-14/ LTC2151-14/LTC2150-14 TYPICAL APPLICATIONS C11 47F 1210 L5 BEAD C12 0.1F C34 0.1F C35 0.1F SDO SDI SCK CS PAR/SER VDD D10_11- + D10_11+ C10 1F D12_13- REGULATED 1.8V VDD OVDD D12_13+ L4 BEAD 4 R16 100 5 SENSE 6 7 8 10 C16 2.2F 9 10 41 C21 0.1F D10_11+ 32 D10_11- 31 SDO 36 GND 35 D12_13+ 34 D12_13- 33 OVDD D8_9- + AINA CLKOUT+ AINA- CLKOUT - LTC2152-14 GND D6_7+ SENSE D6_7- VREF D4_5+ VCM D4_5- GND 30 + 29 D8_9 GND GND 0.1F OGND 28 27 26 25 24 23 22 21 OVDD D8_9+ D8_9- CLKOUT+ CLKOUT - D6_7+ D6_7 - D4_5+ D4_5- DD R19 10 3 VDD 19 D2_3+ 20 OV AINA R14 10 VDD 17 D0_1+ 18 D2_3- - 2 15 OF + 16 D0_1- AINA 1 13 GND 14 OF - + C13 2.2F 11 CLK+ 12 CLK- SENSE SCK 38 SDI 37 R9, 1k PAR/SER 40 CS 39 0.2F TP3 21521014 TA02 0.1F D2_3+ D2_3- D0_1+ D0_1 - OF + OF - 0.1F OVDD 0.1F 100 CLK+ CLK- 21521014f 30 LTC2152-14/ LTC2151-14/LTC2150-14 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UJ Package 40-Lead Plastic QFN (6mm x 6mm) (Reference LTC DWG # 05-08-1728 Rev O) 0.70 0.05 6.50 0.05 5.10 0.05 4.42 0.05 4.50 0.05 (4 SIDES) 4.42 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 6.00 0.10 (4 SIDES) 0.75 0.05 R = 0.10 TYP R = 0.115 TYP 39 40 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 4.50 REF (4-SIDES) 4.42 0.10 2 PIN 1 NOTCH R = 0.45 OR 0.35 45 CHAMFER 4.42 0.10 (UJ40) QFN REV O 0406 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING IS A JEDEC PACKAGE OUTLINE VARIATION OF (WJJD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD 21521014f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 31 LTC2152-14/ LTC2151-14/LTC2150-14 Typical Application LTC2152-14 32K Point FFT, fIN = 15MHz, -1dBFS, 250Msps 0 VDD OVDD CLOCK S/H 14-BIT PIPELINED ADC CORRECTION LOGIC D12_13 * * * D0_1 OUTPUT DRIVERS OGND CLOCK/DUTY CYCLE CONTROL DDR LVDS AMPLITUDE (dBFS) ANALOG INPUT -20 -40 -60 -80 -100 21521014 TA03a -120 0 20 40 60 80 100 FREQUENCY (MHz) 120 21521014 TA03b Related Parts PART NUMBER DESCRIPTION COMMENTS 16-Bit, 130Msps, 3.3V ADC, LVDS Outputs 1250mW, 77.7dB SNR, 100dB SFDR, 48-Pin QFN ADCs LTC2208 LTC2157-14/ LTC2156-14/ 14-Bit, 250Msps/210Msps/170Msps, LTC2155-14 1.8V Dual ADC, LVDS DDR Outputs 650mW/616mW/567mW 70dB SNR, 80dB SFDR, 9mm x 9mm 64-Pin QFN LTC2242-10/LTC2241-10/ LTC2241-10 10-Bit, 250Msps/210Msps/170Msps, 2.5V ADC, LVDS Outputs 740mW/585mW/445mW, 60.6dB SNR, 78dB SFDR, 64-Pin QFN LTC2242-12/LTC2241-12/ LTC2240-12 12-Bit, 250Msps/210Msps/170Msps, 2.5V ADC, LVDS Outputs 740mW/585mW/445mW, 65.5dB SNR, 80dB SFDR, 64-Pin QFN LTC2262-14 14-Bit, 150Msps 1.8V ADC, Ultralow Power 149mW, 72.8dB SNR, 88dB SFDR, DDR LVDS/DDR CMOS/CMOS Outputs, 6mm x 6mm QFN-36 LT5517 40MHz to 900MHz Direct Conversion Quadrature Demodulator High IIP3: 21dBm at 800MHz, Integrated LO Quadrature Generator LT5527 400MHz to 3.7GHz High Linearity Downconverting Mixer 24.5dBm IIP3 at 900MHz, 23.5dBm IIP3 at 3.5GHz, NF = 12.5dB, 50 Single-Ended RF and LO Ports LT5575 800MHz to 2.7GHz Direct Conversion Quadrature Demodulator High IIP3: 28dBm at 900MHz, Integrated LO Quadrature Generator, Integrated RF and LO Transformer LTC6409 10GHz GBW, 1.1nV/Hz Differential Amplifier/ ADC Driver 88dB SFDR at 100MHz, Input Range Includes Ground 52mA Supply Current 3mm x 2mm QFN Package LTC6412 800MHz, 31dB Range, Analog-Controlled Variable Gain Amplifier Continuously Adjustable Gain Control, 35dBm OIP3 at 240MHz, 10dB Noise Figure, 4mm x 4mm QFN-24 LTC6420-20 1.8GHz Dual Low Noise, Low Distortion Differential ADC Drivers for 300MHz IF Fixed Gain 10V/V, 1nV/Hz Total Input Noise, 80mA Supply Current per Amplifier, 3mm x 4mm QFN-20 LTM9002 14-Bit Dual Channel IF/Baseband Receiver Subsystem Integrated High Speed ADC, Passive Filters and Fixed Gain Differential Amplifiers LTM9003 12-Bit Digital Pre-Distortion Receiver Integrated 12-Bit ADC Down-Converter Mixer with 0.4GHz to 3.8GHz Input Frequency Range RF Mixers/Demodulators Amplifiers/Filters Receiver Subsystems 21521014f 32 Linear Technology Corporation LT 0811 * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2011