Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model
P
D
2
4
2
5
N
5050
S
2
Rev C
Ultra Low Profile 0404 Power Divider
50Ω to 50Ω
Description
The PD2425N5050S2 is a low profile 1mm square, sub-miniature Wilkinson power
divider in an easy to use surface mount package. The PD2425N5050S2 is ideal for
high volume manufacturing and delivers higher performances than traditional printed
and lumped element solutions. The PD2425N5050S2 is matched to 50Ω and has a
height profile of 0.6 mm with an LGA interface which is ideal for high level
integrations in module level solutions in the following markets: WiMAX (2.3 - 2.7
GHz), 802.11b, g & n, 2.4 GHz ISM band, Bluetooth (LE), Bluetooth and ZigBee.
The PD2425N5050S2 does not include the resistive element and therefore, requires
an external resistor for operation. The PD2425N5050S2 is available on tape and
reel for high volume manufacturing pick and place.
Detailed Electrical Specifications:
Specifications subject to change without notice.
ROOM (25°
°°
°C)
Parameter Min. Typ. Max Unit
Frequency 2400 2500 MHz
Input Port Impedance 50 Ω
Output Port Impedance 50 Ω
Return Loss 21 27 dB
Insertion Loss* 0.39 0.46 dB
Amplitude Balance 0.01 0.35 dB
Phase Balance 0.5 1.3 Degrees
Isolation (Output Ports) 20 23 dB
Power Handling 0.5 Watts
Features:
• 2400-2500 MHz
• 23 dB Isolation (output ports)
• Good Return Loss
• 0.6 mm Height Profile
• 50Ω Input / 50Ω Outputs
• Low Insertion Loss
• Surface Mountable
• Tape & Reel
• Non-conductive Surface
• RoHS Compliant
• External Resistor Required
• Halogen Free Operating Temperature -55 +85 ºC
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
.23
.23
1.04
±.10
1.04
±.10
.62
±.05
.33
.33
.50
.50
3x .25
3x .25
1
2
43
Bottom View (Far-side)Side ViewTop View (Near-side)
Mechanical Outline
Dimensions are in Millimeters
Tolerances are Non-Cumulative
Input
GND
4
3
Designation
Pin
1
2
Output 1
Output 2
3x .27
3x .27
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model
P
D
2
4
2
5
N
5050
S
2
Rev C
Outline Drawing
Typical Broadband Performance: 500 MHz. to 8.0 GHz.
Isolation
Return Loss Insertion Loss
Amplitude Balance Phase Balance
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model
P
D
2
4
2
5
N
5050
S
2
Rev C
Typical Performance: 2200 MHz. to 2900 MHz.
Return Loss
Amplitude Balance
Isolation
Phase Balance
Insertion Loss
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model
P
D
2
4
2
5
N
5050
S
2
Rev C
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and
ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances. In addition, since the PD2425S5050S2 is a Wilkinson power divider, an
external 0201 100Ω resistor must be mounted in locations R1 as shown in the Figure below.
Pad Footprint w/ 0201 Resistor Locations
Dimensions are in Millimeters
Mounting Footprint
Plated thru
hole to
ground
Solder Resist
Footprint Pad (s)
Circuit Pattern
3x Transmission
Line .50
3x .29 SQ.
.36 SQ.
2x .21
.50
.21
0201
Resistor
3x .29
.13
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model
P
D
2
4
2
5
N
5050
S
2
Rev C
Packaging and Ordering Information
Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information
.
4.00
Ø1.50
1.21
.70
.18
4.00
1.21
2.00
8.00
3.50
1.75
