Prelimanary W541L20X Data Sheet 4-BIT MICROCONTROLLER Table of Contents1. GENERAL DESCRIPTION .............................................................................................................. 2 2. FEATURES ...................................................................................................................................... 2 3. BLOCK DIAGRAM ........................................................................................................................... 4 4. PIN CONFIGURATIONS.................................................................................................................. 5 5. PIN DESCRIPTION.......................................................................................................................... 6 6. ELECTRICAL CHARACTERISTICS................................................................................................ 7 6.1 Absolute Maximum Ratings ................................................................................................... 7 6.2 DC Characteristics ................................................................................................................. 7 6.3 AC Characteristics ................................................................................................................. 8 7. APPLICATION CIRCUIT.................................................................................................................. 9 8. PACKAGE DIMENSIONS .............................................................................................................. 10 9. 8.1 18-Lead PDIP-300mil........................................................................................................... 10 8.2 20-Lead PDIP ...................................................................................................................... 11 8.3 28-Lead PDIP Skinny........................................................................................................... 12 8.4 20-Lead SOP-300mil ........................................................................................................... 13 8.5 28-Lead SOP-300mil ........................................................................................................... 14 REVISION HISTORY ..................................................................................................................... 15 Publication Release Date: April 14, 2005 -1Revision A5 W541L20X 1. GENERAL DESCRIPTION The W541L20X is a high-performance 4-bit microcontroller (C) that operates on very low current. The device contains a 4-bit ALU, two 8-bit timers, a divider, a serial port, and five 4-bit I/O ports (including 3 output ports for LED driving). There are also seven interrupt sources and 8-level subroutine nesting for interrupt applications. The W541L20X has two power reduction modes, hold mode and stop mode, which help to minimize power dissipation. The W541L20X is suitable for remote controllers, toy controllers, keyboard controllers, speech synthesis LSI controllers, and other products. 2. FEATURES * Operating voltage: 1.2V to 1.8V * Single system clock - Oscillation frequency up to 1 MHz , Crystal or RC oscillator is selected by mask code option , - High-frequency (400 KHz to 1 MHz) or low-frequency (32.768 KHz) oscillation is selected by mask code option * Memory - 2048 x 16 bit program ROM (including 2K x 4 bit look-up table) - 128 x 4 bit data RAM (including 16 working registers) * 21 input/output pins - Input/output ports: 4 ports/16 pins - Serial input/output port: 1 port /4 pins (high sink current for LED driving) - MFP out pin: 1pin (MFP) - Do not be floating when it is as input or output open-drain (NMOS type). * Power-down mode - Hold function: no operation (except for oscillator) - Stop function: no operation (including oscillator) * Seven types of interrupts - Five internal interrupts (Divider 0, Timer 0, Timer 1, and Serial I/O) - Two external interrupts (Port RC and INT pin) * MFP output pin - Output is software selectable as modulating or nonmodulating frequency - Works as frequency output specified by Timer 1 * Built-in 14-bit clock frequency divider circuit -2- W541L20X * Two built-in 8-bit programmable countdown timers - Timer 0: One of two internal clock frequencies (FOSC/4 or FOSC/1024) can be selected - Timer 1: Offers auto-reload function, and one of two internal clock frequencies (FOSC or FOSC/64) can be selected, or falling edge of pin RC.0 can be selected (output through MFP pin) * Built-in 18/14-bit watchdog timer selectable for system reset * Powerful instruction set: 118 instructions * 8-level subroutine (include interrupt) nesting * One serial transmission/receiver port specified by software * Up to 4 S instruction cycle (with 1 MHz operating frequency) * Packaged in 18-pin, 20-pin, 28-pin PDIP and 20-pin, 28-pin SOP Publication Release Date: April 14, 2005 -3Revision A5 W541L20X 3. BLOCK DIAGRAM RAM (128*4) (look_up table ALU 2K*4) +1(+2) STACK (8 Levels) Timer 0 (8-bit) Watchdog Timer (4-bit) RA0 to 3 PORT RB RB0 to 3 PORT RC RC0 to 3 PORT RD RD0 to 3 ACC ROM (2048*16) PC PORT RA Central Control Unit IEF HEF PEF HCF EVF SEF PORT RT PSR0 PSR1 PSR2 PR MR0 PM0 . . . Timer 1 (8-bit) Serial I/O Modulation Frequency Pulse SEL MUX SEL RE0 to 3 MUX (RE0/DOUT, RE1/CLKO, RE2/DIN, RE3/CLKI) MFP VDD VSS Divider 0 (14-bit) Timing Generator INT RES XIN -4- XOUT W541L20X 4. PIN CONFIGURATIONS W541L202/L205 RA2 RA3 INT RES W541L201 RA2 RA3 INT RES VSS RB0 RB1 RB2 RB3 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 RA1 RA0 XIN XOUT VDD RC3 VSS RE0 RE1 RE2 RE3 RB0 RB1 RC2 RC1 RB2 RC0 NC 18-PDIP(300 mil) RB3 RA3 INT RES VSS VSS RB0 RB1 RB2 RB3 1 2 3 4 5 6 7 8 9 10 RA1 RA2 19 RA0 XIN RA3 14 13 12 11 20-PDIP(300 mil) RA1 11 12 13 14 18 17 16 15 RC2 RC1 RC0 RA0 XIN XOUT VDD RD3 RD2 RD1 RD0 RC3 MFP W541L204 20 18 17 16 15 28 27 26 25 24 23 22 21 20 19 28 SKINNY(300 mil), 28 SOP W541L203 RA2 1 2 3 4 5 6 7 8 9 10 XOUT VDD VDD RC3 RC2 RC1 RC0 INT RES VSS 1 2 3 4 5 VSS RB0 RB1 RB2 6 7 8 9 RB3 10 20 RA1 19 RA0 XIN 18 17 16 15 14 13 12 11 XOUT VDD VDD RC3 RC2 RC1 RC0 20 SOP Publication Release Date: April 14, 2005 -5Revision A5 W541L20X 5. PIN DESCRIPTION SYMBOL I/O FUNCTION XIN I Input pin for oscillator. Connected to crystal or resistor to generate system clock by code option. External 10~20pF capacitor uses to get accurate freq in crystal mode. XOUT O Output pin for oscillator. Connected to crystal or resistor to generate system clock by code option. 20pF capacitor is built in internal for crystal mode. RA0-RA3 I/O Input/Output port. Input/output mode specified by port mode 1 register (PM1). When used as output port, can provide high sink current for driving LED. RB0-RB3 I/O Input/Output port. Input/output mode specified by port mode 2 register (PM2). When used as output port, can provide high sink current for driving LED. RC0-RC3 I/O Input/Output port. Input/output mode specified by port mode 4 register (PM4). Each pin has an independent interrupt capability in input mode. And build-in schmitt trigger RD0-RD3 I/O Input/Output port. Input/output mode specified by port mode 5 register (PM5). RE0/DOUT RE1/CLKO RE2/DIN RE3/CLKI I/O Special input/output port. This port can be configured by software to act as the output of internal port RT or the serial I/O port. When used as output port, can provide high sink current for driving LED. MFP O Output pin only. This pin can output modulating or nonmodulating frequency, or Timer 1 clock output specified by mode register 1 (MR1). INT I External interrupt pin with pull-high resistor. RES I System reset pin with pull-high resistor. VDD I Positive power supply (+). VSS I Negative power supply (-). -6- W541L20X 6. ELECTRICAL CHARACTERISTICS 6.1 Absolute Maximum Ratings PARAMETER RATING UNIT Supply Voltage to Ground Potential -0.3 to +7.0 V Applied Input/Output Voltage -0.3 to +7.0 V 120 mW 0 to +70 C -55 to +150 C Power Dissipation Ambient Operating Temperature Storage Temperature Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. 6.2 DC Characteristics (VDD-VSS = 1.5V, Fosc. = 32.768 KHz, Ta = 25 C; unless otherwise specified) PARAMETER SYM. CONDITIONS MIN. TYP. MAX. UNIT Op. Voltage (Crystal type) VDD1 High-frequncy Oscillation 1.35 - 1.8 V Op. Voltage (RC type) VDD2 High-frequncy Oscillation 1.2 - 1.8 V Op. Voltage (RC,Crystal) VDD3 Low-frequncy Oscillation 1.2 - 1.8 V Op. Current (Crystal type) IOP1 No load (Ext-V) - 4 12 A Op. Current (RC type) IOP2 No load (Ext-V) - 35 65 A Hold Current (Crystal type) IHM1 Hold mode No load (Ext-V) - 3 6 A Hold Current (RC type) IHM2 Hold mode No load (Ext-V) - 16 40 A Stop Current (Crystal type) ISM1 Stop mode No load (Ext-V) - 0.1 2 A Stop Current (RC type) ISM2 Stop mode No load (Ext-V) - 0.1 2 A Input Low Voltage VIL - VSS - Input High Voltage VIH - 0.7 VDD - VDD V MFP Output Low Voltage VML IOL = 0.9 mA - 0.1 0.3 V 0.3 VDD V Publication Release Date: April 14, 2005 -7Revision A5 W541L20X 6.2 DC Characteristics, continued PARAMETER SYM. CONDITIONS MIN. TYP. MAX. UNIT 1.2 1.4 - V MFP Output High Voltage VMH IOH = -0.75 mA Port RA, RB Output Low Voltage VABL IOL = 1.0 mA - 0.2 0.3 V Port RA, RB Output High Voltage VABH IOH = 0.5 mA 1.2 1.4 - V Port RC, RD Output Low Voltage VCDL IOL = 1.0 mA - 0.2 0.3 V Port RC, RD Output High Voltage VCDH IOH = -0.5 mA 1.2 1.4 - V Port RE Sink Current IEL VOL = 0.3V 2 - - mA Port RE Source Current IEH VOH = 1.2V 0.35 0.45 - mA 100 250 500 K 100 250 500 K 100 250 500 K INT Pull-up Resistor RINT DIN Pin Pull-up Resistor RDIN RES Pull-up Resistor RRES 6.3 RE.2 used as serial input pin - AC Characteristics (VDD-VSS = 1.5 V, Ta = 25 C; unless otherwise specified) PARAMETER SYM. CONDITIONS MIN. TYP. MAX. UNIT - - 1000 - 32.768 - - 4/FOSC - mS Instruction Cycle Time TI RC type Crystal type 1 (Option low speed type) One machine cycle Serial Port Data Ready Time TDR - 200 - - nS Serial Port Data Hold Time TDH - 200 - - nS Reset Active Width TRAW FOSC = 32.768 KHz 1 - - S Interrupt Active Width TIAW FOSC = 32.768 KHz 1 - - S Op. Frequency FOSC -8- KHz W541L20X 7. APPLICATION CIRCUIT Vcc VDD RA0 Output Signal RA3 Vcc RB0 RB1 RB2 RB3 Vcc RD0 RD1 RD2 RD3 RC0 RC1 RC2 RC3 Vcc INT RE0 RE1 RE2 RE3 RES XOUT Vcc or MFP XIN *1(option) VSS Note : *1 is for accuracy Publication Release Date: April 14, 2005 -9Revision A5 W541L20X 8. PACKAGE DIMENSIONS 8.1 18-Lead PDIP-300mil D 18 10 1 9 1 E E S c 1 2 A A A Base Plane Seating Plane L B e1 B1 Dimension in inches Symbol A A1 A2 B B1 c D E E1 e1 L eA S Min. Nom Max. Dimension in mm Min. Nom 0.010 Max. 4.45 0.175 0.25 0.125 0.130 0.135 3.18 3.30 3.43 0.016 0.018 0.022 0.41 0.46 0.56 0.058 0.060 0.064 1.47 1.52 1.63 0.008 0.010 0.014 0.20 0.25 0.36 0.900 0.910 22.86 23.11 7.87 0.290 0.300 0.310 7.37 7.62 0.245 0.250 0.255 6.22 6.35 6.48 0.090 0.100 0.110 2.29 2.54 2.79 0.120 0.130 0.140 3.05 3.30 3.56 15 0 0.375 8.51 9.02 9.53 0 0.335 0.355 0.055 - 10 - 15 1.40 eA W541L20X 8.2 20-Lead PDIP D 20 11 1 10 1 E E S c 1 2 AA A L Base Plane Seating Plane B e1 eA B1 Dimension in inches Symbol A A1 A2 B B1 c D E E1 e1 L Min. Max. Dimension in mm Min. Nom 0.010 Max. 4.45 0.175 0.25 0.125 0.130 0.135 3.18 3.30 3.43 0.016 0.018 0.022 0.41 0.46 0.56 0.058 0.060 0.064 1.47 1.52 1.63 0.008 0.010 0.014 0.20 0.25 0.36 1.026 1.040 20.06 26.42 7.87 0.290 0.300 0.310 7.37 7.62 0.245 0.250 0.255 6.22 6.35 6.48 0.090 0.100 0.110 2.29 2.54 2.79 0.120 0.130 0.140 3.05 3.30 3.56 15 0 0.375 8.51 9.02 9.53 0 eA 0.335 S Nom 0.355 0.075 15 1.91 Publication Release Date: April 14, 2005 - 11 Revision A5 W541L20X 8.3 28-Lead PDIP Skinny D 28 15 1 14 E1 E S c Base Plane A A2 A1 L Mounting Plane B e1 a B1 Dimension in Inches Symbol A A1 A2 B B1 c Min. Nom Max. Dimension in mm Min. Nom 0.010 Max. 4.45 0.175 0.25 0.125 0.130 0.135 3.18 3.30 3.43 0.016 0.018 0.022 0.41 0.46 0.56 0.058 0.060 0.064 1.47 1.52 1.63 0.010 0.014 0.20 1.388 1.400 0.008 D 0.25 0.36 35.26 35.56 E E1 e1 0.300 0.310 0.320 7.62 7.87 8.13 0.283 0.288 0.293 7.19 7.32 7.44 0.090 0.100 0.110 2.29 2.54 2.79 L 0.120 0.130 0.140 3.05 3.30 3.56 a 0 15 0 0.370 8.38 8.89 9.40 eA S 0.330 0.350 0.055 - 12 - 15 1.40 eA W541L20X 8.4 20-Lead SOP-300mil 11 20 c E HE L 10 1 D 0.25 O A Y SEATING PLANE e GAUGE PLANE A1 b Control demensions are in milmeters . Symbol A A1 b c E D e HE Y L q Dimension in mm Min. 2.35 0.10 0.33 0.23 Max. 2.65 0.30 0.51 0.32 7.40 7.60 13.00 12.60 1.27 BSC 10.65 10.00 0.10 0.40 1.27 0 8 Dimension in inches Min. 0.093 0.004 0.013 Max. 0.104 0.012 0.020 0.009 0.291 0.496 0.013 0.299 0.512 0.050 BSC 0.394 0.419 0.004 0.016 0.050 0 8 Publication Release Date: April 14, 2005 - 13 Revision A5 W541L20X 8.5 28-Lead SOP-300mil 15 28 c E HE L 14 1 D 0.25 O A Y SEATING PLANE e Control demensions are in milmeters . Symbol A A1 b c E D e HE Y L q Dimension in mm Min. 2.35 0.10 0.33 0.23 GAUGE PLANE A1 b Max. 2.65 0.30 0.51 0.32 7.40 7.60 17.70 18.10 1.27 BSC 10.65 10.00 0.10 0.40 1.27 0 8 Dimension in inches Min. Max. 0.093 0.104 0.012 0.004 0.013 0.020 0.009 0.013 0.291 0.299 0.697 0.713 0.050 BSC 0.394 0.419 0.004 0.016 0.050 0 8 - 14 - W541L20X 9. REVISION HISTORY VERSION DATE PAGE DESCRIPTION A2 - - Note : Recommend working voltage range for Hi freq all mode ( L series) A3 - - Note: RC is built-in schmitt trigger A4 June 3, 2003 - Note: Do not be floating when it is as input or output open-drain (NMOS type) A5 April 14, 2005 - Add Important Notice Important Notice Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. Publication Release Date: April 14, 2005 - 15 Revision A5