AR0833 AR0833 1/3.2Inch 8 Mp CMOS Digital Image Sensor Table 1. KEY PERFORMANCE PARAMETERS Parameter Typical Value www.onsemi.com Array Format 3264 x 2448 Primary Modes Full Resolution: 4:3 - 8 Mp at 30 fps 16:9 - 6 Mp at 30 fps 16:9 - 1080p HD at 30 fps Pixel Size 1.4 m Back Side Illuminated (BSI) Optical Format 1/3.2-inch Die Size 6.86 mm x 6.44 mm (Area: 44.17 mm2) Input Clock Frequency 6-27 MHz Interface MIPI CSI-2 (2-, 3-, 4-lane Modes Supported.) 800 Mbps Max MIPI Clock Speed per Lane. Subsampling Modes X - Bin2, Sum2 Skip: 2x, 4x CLCC48 10 y 10 CASE 848AJ ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. Y - Sum2, Skip: 2x, 4x, 8x Output Data Depth 10 bits Raw or 8/6-bit DPCM Analog Gain 1x, 2x, 3x, 4x, 6x, 8x High Quality Bayer Scalar Adjustable Scaling Up to 1/6x scaling Temperature Sensor 10-bit, Single Instance on Chip, Controlled by Two-wire Serial I/F VCM AF Driver 8-bit Resolution With Slew Rate Control 3-D Support Frame Rate and Exposure Synchronization Supply Voltage Features (Continued) * Data Interfaces: Two-, Three-, and Four-lane * Analog 2.5-3.1 V (2.8 V Nominal) Digital 1.14-1.3 V (1.2 V Nominal) Pixel 2.5-3.1 V (2.8 V Nominal) OTPM Read 1.7-1.9 V (1.8 V Nominal) * * * I/O 1.7-1.9 V (1.8 V Nominal) or 2.5-3.1 V (2.8 V Nominal) * * MIPI 1.14-1.3 V (1.2 V Nominal) Power Consumption 340 mW at 30 fps, 8 Mp Responsivity 0.6 V/lux-sec SNRMAX 36 dB Dynamic Range 64 dB Operating Temperature Range (at Junction) -TJ -30C to +70C * * Features * High-speed Sensor Supporting 8 Mp (4:3) 30 fps Still Images and * * Full HD 1080p30 Video 1.4 Pixel with ON Semiconductor A-PixHSTM Technology Providing Best-in-class Low-light Performance. Optional On-chip high-quality Bayer Scaler to Resize Image to Desired Size (c) Semiconductor Components Industries, LLC, 2011 June, 2018 - Rev. 11 1 * * Serial Mobile Industry Processor Interface (MIPI) Bit-depth Compression Available for MIPI Interface: 10-8 and 10-6 to Enable Lower Bandwidth Receivers for Full Frame Rate Applications On-chip Temperature Sensor On-die phase-locked Loop (PLL) Oscillator 5.6 Kb One-time Programmable Memory (OTPM) for Storing Module Information On-chip 8-bit VCM Driver 3D Synchronization Controls to Enable Stereo Video Capture Interlaced Multi-exposure Readout Enabling High Dynamic Range (HDR) Still and Video Applications Programmable Controls: Gain, Horizontal and Vertical Blanking, Auto Black Level Offset Correction, Frame Size/rate, Exposure, Left-right and Top-bottom Image Reversal, Window Size, and Panning Support for External Mechanical Shutter Support for External LED or Xenon Flash Applications * Smart phones * PC cameras * Tablets Publication Order Number: AR0833/D AR0833 Table 2. MODES OF OPERATION AND POWER CONSUMPTION AT 100% FOV Active Readout Window (Col y Row) Sensor Output Resolution (Col y Row) Mode FPS Power Consumption [mW] (Note 5) Full Resolution 4:3 - 8 Mp (Note 1) 3264 x 2448 3264 x 2448 Full mode 30 340 Full Resolution 16:9 - 6 Mp (Note 1) 3264 x 1836 3265 x 1836 Full mode 30 323 VGA (Note 2) 3264 x 2448 640 x 480 Scaling 30 293 VGA (Note 3) 3264 x 2448 640 x 480 Bin2 + Scaling 30 270 VGA 3264 x 2448 640 x 480 Bin2 + Scaling 60 293 1080p (Note 2) 3264 x 1836 1920 x 1080 Scaling 30 216 1080p + EIS (Note 2, 4) 3264 x 1836 2304 x 1296 Scaling 30 216 720p (Note 2) 3264 x 1836 1280 x 720 Scaling 30 216 720p (Note 2) 3264 x 1836 1280 x 720 Bin2 + Scaling 60 295 720p + EIS (Note 2) 3264 x 1836 1536 x 864 Scaling 30 216 WVGA (Note 2) 3264 x 1836 8546 x 480 Scaling 30 256 WVGA (Note 2) 3265 x 1836 856 x 480 Bin2 + Scaling 60 293 Mode SNAPSHOT MODE 4:3 VIDEO MODE 16:9 VIDEO MODE 1. 2. 3. 4. 5. 732 Mbps/lane MIPI data transfer rate Scaled image using internal High Quality Bayer Scaler Low power preview Electronic Image Stabilization Values measured at T = 25C and nominal voltages ORDERING INFORMATION Table 3. AVAILABLE PART NUMBERS Part Number AR0833CS3C12SUAA0-DP Product Description 8 MP 1/3 CIS Orderable Product Attribute Description Dry Pack with Protective Film shutter lag snapshot mode. It is programmable through a simple two-wire serial interface and has very low power consumption. The AR0833 digital image sensor features ON Semiconductor's breakthrough low-noise 1.4 m pixel CMOS imaging technology that achieves near-CCD image quality (based on signal-to-noise ratio and low-light sensitivity) while maintaining the inherent size, cost, and integration advantages of CMOS. The AR0833 sensor can generate full resolution image at up to 30 frames per second (fps). An on-chip analog-to-digital converter (ADC) generates a 10-bit value for each pixel. See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at www.onsemi.com. GENERAL DESCRIPTION The ON Semiconductor AR0833 is a 1/3.2-inch BSI (back side illuminated) CMOS active-pixel digital image sensor with a pixel array of 3264 (H) x 2448 (V) (3280 (H) x 2464 (V) including border pixels). It incorporates sophisticated on-chip camera functions such as mirroring, column and row skip modes, and context switching for zero www.onsemi.com 2 AR0833 FUNCTIONAL OVERVIEW In order to meet higher frame rates in AR0833 sensor, the architecture has been re-designed. The analog core has a column parallel architecture with 4 data paths. Digital block has been re-architected to have 4 data paths. The chip is targeted to meet SMIA 85 module size. As a result, the final die size is 6.86 mm x 6.44 mm (singulated) which would fit in the intended module with two-sided pad frame. Figure 1 shows the block diagram of the AR0833. DVDD_1V2_ PHY Gain Control MIPI FIFO&Optional Compression Two-wire Serial Interface SCLK VCM Control VCM GPI[3:2] GPIO[1:0] XSHUTDOWN External Clock Timing Control Scaler Register Control AR0833 PLL MIPI Serial Data Output [3:0] SDATA 10-bit Temperature Sensor ADC Digital Gain Gain Test Pattern Generator Row Driver VDD_IO, DVDD_1V8, DVDD_1V2 Pixel Array Image Output Digital Processing Data Calibration Imaging Sensor Core VAA, VAA_PIX Figure 1. Top Level Block Diagram The core of the sensor is an 8 Mp active-pixel array. The timing and control circuitry sequences through the rows of the array, resetting and then reading each row in turn. In the time interval between resetting a row and reading that row, the pixels in the row integrate incident light. The exposure is controlled by varying the time interval between reset and readout. Once a row has been read, the data from the columns is sequenced through an analog signal chain (providing gain), and then through an ADC. The output from the ADC is a 10-bit value for each pixel in the array. The ADC output passes through a digital processing signal chain (which provides further data path corrections and applies digital gain). The pixel array contains optically active and light-shielded ("dark") pixels. The dark pixels are used to provide data for on-chip offset-correction algorithms ("black level" control). The sensor contains a set of control and status registers that can be used to control many aspects of the sensor behavior including the frame size, exposure, and gain setting. These registers can be accessed through a two-wire serial interface. The output from the sensor is a Bayer pattern; alternate rows are a sequence of either green and red pixels or blue and green pixels. The offset and gain stages of the analog signal chain provide per-color control of the pixel data. A flash output signal is provided to allow an external xenon or LED light source to synchronize with the sensor exposure time. Additional I/O signals support the provision of an external mechanical shutter. Pixel Array The sensor core uses a Bayer color pattern, as shown in Figure 2. The even-numbered rows contain green and red pixels; odd-numbered rows contain blue and green pixels. Even-numbered columns contain red and green pixels; odd-numbered columns contain blue and green pixels. ... Column Readout Direction Black Pixels Row Readout Direction First Pixel (Col. 0, Row 60) ... R Gr R Gr R Gb B Gb B Gb R Gr R Gr R Gb B Gb B Gb NOTE: By default the mirror bit is set, so the read-out direction is from left to right. Figure 2. Pixel Color Pattern Detail (Top Right Corner) www.onsemi.com 3 AR0833 TYPICAL CONNECTIONS The chip supports MIPI output protocol. MIPI can be configured in 4-, 3- or 2-lanes. There are no parallel data output ports. 1.5 kW2, 3 1.5 kW2 2.8 V or 1.8 V VDD_IO (IO) Two-wire Serial Interface 1.8 V 1.2 V DVDD_1V8 (OTPM Read)6 2.8 V VAA4 (Analog) DVDD_1V2 (Digital)7 VAA4 (Pixel) DVDD1V2_PHY (MIPI)7 SCLK DATA_P SDATA DATA_N EXTCLK (6-27 MHz) DATA2_P DATA2_N General Purpose Input/Output 1.2 V GPIO[1:0] DATA3_P DATA3_N GPI[3:2] To MIPI Port DATA4_N DATA4_P XSHUTDOWN CLK_P AGND VCM ISINK VCM GND DGND GND_IO TEST8 CLK_N GNDPHY ATEST8 VPP5 (OTPM Write) (Only Connected while Programming OTPM) VCM 1 2.8 V 0.1 mF 0.01 mF 1.2 V DVDD_1V8 VDD_IO 0.1 mF 1.0 mF 1.0 mF 0.1 mF 0.1 mF Notes: 1. All power supplies should be adequately decoupled; recommended cap values are: - 2.8 V: 1.0 mF, 0.1 mF, and then 0.01 mF - 1.2 V: 1 mF and then 0.1 mF - 1.8 V: 0.1 mF 2. Resistor value 1.5 kW is recommended, but may be greater for slower two-wire speed. 3. This pull-up resistor is not required if the controller drives a valid logic level on SCLK at all times. 4. VAA and VAA_PIX can be tied together. However, for noise immunity it is recommended to have them separate (i.e. two sets of 2.8 V decoupling caps). 5. VPP, 6-7 V, is used for programming OTPM. This pad is left unconnected if OTPM is not being programmed. 6. VDD_1V8 can be combined with VDD_IO, if VDD_IO = 1.8 V. 7. VDD_1V2 and VDD1_1V2_PHY can be tied together. 8. ATEST1 can be left floating. 9. TEST pin must be tied to DGND. 10. DVDD_1V8 is the OTPM read voltage (must always be provided). Figure 3. Typical Application Circuit - MIPI Connection www.onsemi.com 4 AR0833 SIGNAL DESCRIPTIONS AR0833 has 67 pads placed in a two sided pad frame. It has only serial outputs. The part may be configured as MIPI with different bit depths. The pad description is tabulated in Table 4: Table 4. PAD DESCRIPTIONS Pad Name Pad Type Description SENSOR CONTROL EXTCLK Input Master clock input; PLL input clock. 6 MHz-27 MHz This is a SMIA-compliant pad GPIO0 Input/Output General Input and one Output function include: a. (Default Output) Flash b. (Input) all options in GPI2 High-Z before XSHUTDOWN going high; default value is `0' after all three voltages in place and XSHUTDOWN being high After reset, this pad is not powered down since its default use is as Flash pin If not used, can be left floating GPIO1 Input/Output General Input and 2 Output functions include: a. (Default Output) Shutter b. (Output) 3-D daisy chain communication output c. (Input) all options in GPI2 High-Z before XSHUTDOWN going high; default value is `0' after all three voltages in place and XSHUTDOWN being high After reset, this pad is not powered-down since its default use is as Shutter pin If not used, can be left floating GPI2 Input General Input; After reset, these pads are powered down by default; this means that it is not necessary to bond to these pads. Functions include: a. SADDR, switch to the second two-wire serial interface device address (see "Slave Address/Data Direction Byte") b. Trigger signal for Slave Mode c. Standby If not used, can be left floating GPI3 Input General Input; After reset, these pads are powered-down by default; this means that it is not necessary to bond to these pads. Functions include: a. 3-D daisy chain communication input b. All options in GPI2 If not used, can be left floating TWO-WIRE SERIAL INTERFACE SCLK Input SDATA I/O Serial clock for access to control and status registers Serial data for reads from and writes to control and status registers SERIAL OUTPUT DATA[4:1]P Output Differential serial data (positive). DATA[4:1]N Output Differential serial data (negative) CLK_P Output Differential serial clock/strobe (positive) CLK_N Output Differential serial clock/strobe (negative) XSHUTDOWN Input Asynchronous active LOW reset. When asserted, data output stops and all internal registers are restored to their factory default settings. This pin will turn off the digital power domain and is the lowest power state of the sensor VCM DRIVER VCM_ISINK Input/Output VCM Driver current sink output. If not used, it could be left floating VCM_GND Input/Output Ground connection to VCM Driver. If not used, needs to be connected to ground (DGND). This ground must be separate from the other grounds Input/Output High-voltage pin for programming OTPM, present on sensors with that capability. This pin can be left floating during normal operation POWER VPP www.onsemi.com 5 AR0833 Table 4. PAD DESCRIPTIONS (continued) Pad Name Pad Type Description Supply Power supply. The domains are specified in the next table. The brackets indicate the number of individual pins POWER (continued) VAA[7:1], VAA_PIX[2:1], AGND[9:1], VDD_IO_[4:1], GND_IO, DGND_[6:1], DVDD_1V2_[9:1], DVDD_1V2_PHY_[2:1], GNDPHY_[2:1], DVDD_1V8 There are standard GPI and GPIO pads, two each. Chip can also be communicated to through the two-wire serial interface. The chip has three unique power supply requirements: 1.2 V, 1.8 V, and 2.8 V. These are further divided and in all there are seven power domains and five independent ground domains from the ESD perspective. Table 5. INDEPENDENT POWER AND GROUND DOMAINS Pad Name Power Supply DGND (GNDPHY, GND_IO) 0V Digital VCM_GND 0V VCM Driver AGND 0V Analog VAA 2.8 V Analog/VCM Driver/OTPM VAA_PIX 2.8 V Pixel/Analog DVDD_1V2 1.2 V Digital VDD_IO 1.8 V/2.8 V DVDD_1V2_PHY 1.2 V MIPI DVDD_1V8 1.8 V OTPM Description GROUNDS POWER www.onsemi.com 6 IO AR0833 SYSTEM STATES The system states of the AR0833 are represented as a state diagram in Figure 4 and described in subsequent sections. The sensor's operation is broken down into three separate states: hardware standby, software standby, and streaming. The transition between these states might take a certain amount of clock cycles as outlined in Figure 4 and Figure 5. Power Supplies Turned Off (Asynchronous from Any State) Powered OFF XSHUTDOWN = 0 Powered On Hardware Standby EXTCLK Cycles XSHUTDOWN = 1 Internal Initialization Two-wire Serial Interface Write: software_reset = 1 Timeout Software Standby Two-wire Serial Interface Write: mode_select = 1 PLL Not Locked PLL Lock Streaming Frame in Progress PLL Locked Streaming Wait for Frame End Two-wire Serial Interface Write: mode_select = 0 Figure 4. System States www.onsemi.com 7 AR0833 SENSOR INITIALIZATION The power sequence is governed by controlled vs controlling behavior of a power supply and the inrush current (i.e., current that exists when not all power supplies are present). Power-Up Sequence AR0833 has three voltage supplies divided into several domains. The three voltages are 1.2 V, 1.8 V, and 2.8 V. For proper operation of the chip, a power-up sequence is recommended as shown in Figure 5. Table 6. INRUSH CONSIDERATION XSHUTDOWN 1.2 V 1.8 V (VDD_IO) 2.8 V x Present Absent Absent Not Supported x Absent Present Absent Supported Comment x Absent Absent Present Supported x Present Present Absent Supported x Present Absent Present Not Supported x Absent Present Present Supported 0 Present Present Present Powered Down State 1 Present Present Present Powered Up State is controlled by 1.2 V signals. The dedicated 1.8 V domain is used only for OTPM read function, so can turn on along with 1.8 V supply. Due to the above considerations, the suggested power-on sequence is as shown in Figure 5: Since VDD_IO supply controls the XSHUTDOWN, it should be turned on first. The sequence of powering up the other two domains is not too critical. While turning on 2.8 V supply before 1.2 V supply shouldn't be an issue as shown in Table 1, it is still not recommended since the 2.8 V domain VDD_IO, VDD_1V8 VDD_1V2, VDD_1V2_PHY VAA, VAA_PIX t0 t1 t2 EXTCLK t3 XSHUTDOWN t4 Hard Reset Internal Init t5 Soft Standby PLL Lock SDATA SCLK First Serial Write Figure 5. Recommended Power-Up Sequence www.onsemi.com 8 Streaming AR0833 Table 7. POWER-UP SEQUENCE Symbol Definition Minimum Typical Maximum Unit - - 500 ms DVDD_1V8 to DVDD_1V2/DVDD_1V2_PHY 0.2 - 500 ms SDVDD_1V2/DVDD_1V2_PHY to VAA/VAA_PIX 0.2 - 500 ms t0 VDD_IO to DVDD_1V8 t1 t2 t3 Active Hard Reset t4 Internal Initialization t5 PLL Lock Time 1 - 500 ms 2400 - - EXTCLKs 1 - 5 ms Power-Down Sequence 3. After XSHUTDOWN is LOW disable the 2.8 V/1.8 V supply. 4. After the 2.8 V/1.8 V supply is LOW disable the 1.2 V supply. 5. After the 1.2 V supply is LOW disable the VDD_IO supply. The recommended power-down sequence for the AR0833 is shown in Figure 6. The three power supply domains (1.2 V, 1.8 V, and 2.8 V) must have the separation specified below. 1. Disable streaming if output is active by setting standby R0x301a[2] = 0. 2. After disabling the internal clock EXTCLK, disable XSHUTDOWN. t1 VAA, VAA_PIX t2 VDD_1V8 VDD_1V2, VDD_1V2_PHY t3 VDD_IO EXTCLK t0 XSHUTDOWN Streaming Focal Planes Deactivation Soft Standby Hard Reset Turn Off Power Supplies SDATA SCLK Figure 6. Recommended Power-Down Sequence Table 8. POWER-DOWN SEQUENCE Symbol Definition Minimum Typical Maximum Unit t0 EXTCLK to XSHUTDOWN 100 - - ms t1 XSHUTDOWN to Supply 2.8 V/1.8 V 200 - - ms t2 Supply 2.8 V/1.8 V to Supply 1.2 V 0 200 - ms t3 Supply 1.2 V to VDD_IO 200 - - ms www.onsemi.com 9 AR0833 Hard Standby and Hard Reset 2. The soft standby state is reached after the current row or frame, depending on configuration, has ended. 3. Assert XSHUTDOWN (active LOW) to reset the sensor. 4. The sensor remains in hard standby state if XSHUTDOWN remains in the logic "0" state. The hard standby state is reached by the assertion of the XSHUTDOWN pad (hard reset). Register values are not retained by this action, and will be returned to their default values once hard reset is completed. The minimum power consumption is achieved by the hard standby state. The details of the sequence are described below and shown in Figure 7. 1. Disable streaming if output is active by setting mode_select 0x301A[2] = 0. EXTCLK New Row/Frame mode_select R0x0100 Logic "1" Logic "0" XSHUTDOWN Streaming Soft Standby Hard Standby Hard Reset Figure 7. Hard Standby and Hard Reset Soft Standby and Soft Reset Soft Reset 1. Follow the soft standby sequence list above. 2. Set software_reset = 1 (R0x3021) to start the internal initialization sequence. 3. After 2400 EXTCLKs (tentative), the internal initialization sequence is completed and the current state returns to soft standby automatically. The AR0833 can reduce power consumption by switching to the soft standby state when the output is not needed. Register values are retained in the soft standby state. The details of the sequence are described below and shown in Figure 8. Soft Standby 1. Disable streaming if output is active by setting mode_select 0x301A[2] = 0. 2. The soft standby state is reached after the current row or frame, depending on configuration, has ended. EXTCLK Next Row/Frame mode_select R0x0100 software_reset R0x0103 Logic "1" Logic "0" Logic "1" Logic "0" Logic "0" 2400 480 EXTCLKs Streaming Soft Standby Soft Reset Figure 8. Soft Standby and Soft Reset www.onsemi.com 10 Soft Standby AR0833 TWO-WIRE SERIAL REGISTER INTERFACE A two-wire serial interface bus enables read/write access to control and status registers within the AR0833. The two-wire serial interface is fully compatible with the I2C standard. The interface protocol uses a master/slave model in which a master controls one or more slave devices. The sensor acts as a slave device. The master generates a clock (SCLK) that is an input to the sensor and is used to synchronize transfers. Data is transferred between the master and the slave on a bidirectional signal (SDATA). SDATA is pulled up to VDD off-chip by a 1.5 k resistor. Either the slave or master device can drive SDATA LOW-the interface protocol determines which device is allowed to drive SDATA at any given time. The protocols described in the two-wire serial interface specification allow the slave device to drive SCLK LOW; the AR0833 uses SCLK as an input only and therefore never drives it LOW. The electrical and timing specifications are further detailed on "Two-Wire Serial Register Interface". Slave Address/Data Direction Byte Bits [7:1] of this byte represent the device slave address and bit [0] indicates the data transfer direction. A "0" in bit [0] indicates a WRITE, and a "1" indicates a READ. The default slave addresses used by the AR0833 for the MIPI configured sensor are 0x6C (write address) and 0x6D (read address) in accordance with the MIPI specification. Alternate slave addresses of 0x6E(write address) and 0x6F(read address) can be selected by enabling and asserting the SADDR signal through the GPI pad. The alternate slave addresses can also be programmed through R0x31FC. Message Byte Message bytes are used for sending register addresses and register write data to the slave device and for retrieving register read data. Acknowledge Bit Each 8-bit data transfer is followed by an acknowledge bit or a no-acknowledge bit in the SCLK clock period following the data transfer. The transmitter (which is the master when writing, or the slave when reading) releases SDATA. The receiver indicates an acknowledge bit by driving SDATA LOW. Protocol Data transfers on the two-wire serial interface bus are performed by a sequence of low-level protocol elements: 1. a (repeated) start condition 2. a slave address/data direction byte 3. an (a no) acknowledge bit 4. a message byte 5. a stop condition No-Acknowledge Bit The no-acknowledge bit is generated when the receiver does not drive SDATA LOW during the SCLK clock period following a data transfer. A no-acknowledge bit is used to terminate a read sequence. The bus is idle when both SCLK and SDATA are HIGH. Control of the bus is initiated with a start condition, and the bus is released with a stop condition. Only the master can generate the start and stop conditions. Typical Sequence A typical READ or WRITE sequence begins by the master generating a start condition on the bus. After the start condition, the master sends the 8-bit slave address/data direction byte. The last bit indicates whether the request is for a read or a write, where a "0" indicates a write and a "1" indicates a read. If the address matches the address of the slave device, the slave device acknowledges receipt of the address by generating an acknowledge bit on the bus. If the request was a WRITE, the master then transfers the 16-bit register address to which the WRITE should take place. This transfer takes place as two 8-bit sequences and the slave sends an acknowledge bit after each sequence to indicate that the byte has been received. The master then transfers the data as an 8-bit sequence; the slave sends an acknowledge bit at the end of the sequence. The master stops writing by generating a (re)start or stop condition. If the request was a READ, the master sends the 8-bit write slave address/data direction byte and 16-bit register address, the same way as with a WRITE request. The master then generates a (re)start condition and the 8-bit read slave address/data direction byte, and clocks out the register data, eight bits at a time. The master generates an acknowledge bit after each 8-bit transfer. The slave's internal register address is automatically incremented after every 8 bits are transferred. The data transfer is stopped when the master sends a no-acknowledge bit. Start Condition A start condition is defined as a HIGH-to-LOW transition on SDATA while SCLK is HIGH. At the end of a transfer, the master can generate a start condition without previously generating a stop condition; this is known as a "repeated start" or "restart" condition. Stop Condition A stop condition is defined as a LOW-to-HIGH transition on SDATA while SCLK is HIGH. Data Transfer Data is transferred serially, 8 bits at a time, with the MSB transmitted first. Each byte of data is followed by an acknowledge bit or a no-acknowledge bit. This data transfer mechanism is used for the slave address/data direction byte and for message bytes. One data bit is transferred during each SCLK clock period. SDATA can change when SCLK is LOW and must be stable while SCLK is HIGH. www.onsemi.com 11 AR0833 Single READ from Random Location register data. The master terminates the READ by generating a no-acknowledge bit followed by a stop condition. Figure 9 shows how the internal register address maintained by the AR0833 is loaded and incremented as the sequence proceeds. This sequence (Figure 9) starts with a dummy WRITE to the 16-bit address that is to be used for the READ. The master terminates the WRITE by generating a restart condition. The master then sends the 8-bit read slave address/data direction byte and clocks out one byte of Previous Reg Address, N S Slave Address 0 A S = Start Condition P = Stop Condition Sr = Restart Condition A = Acknowledge A = No-acknowledge Reg Address[15:8] Reg Address, M Reg Address[7:0] A A Sr Slave Address 1 A M+1 Read Data A P Slave to Master Master to Slave Figure 9. Single READ from Random Location Single READ from Current Location master terminates the READ by generating a no-acknowledge bit followed by a stop condition. The figure shows two independent READ sequences. This sequence (Figure 10) performs a read using the current value of the AR0833 internal register address. The Previous Reg Address, N S Slave Address 1 A Reg Address, N+1 Read Data A P S Slave Address N+2 1 A Read Data A P Figure 10. Single READ from Current Location Sequential READ, Start from Random Location has been transferred, the master generates an acknowledge bit and continues to perform byte READs until "L" bytes have been read. This sequence (Figure 11) starts in the same way as the single READ from random location (Figure 9). Instead of generating a no-acknowledge bit after the first byte of data Previous Reg Address, N S Slave Address 0 A Reg Address[15:8] M+1 Read Data A Reg Address[7:0] M+2 A Read Data Reg Address, M M+3 A Sr Slave Address M+L-2 A Read Data 1 A M+L-1 A Read Data Figure 11. Sequential READ, Start from Random Location www.onsemi.com 12 M+1 Read Data M+L A P A AR0833 Sequential READ, Start from Current Location has been transferred, the master generates an acknowledge bit and continues to perform byte READs until "L" bytes have been read. This sequence (Figure 12) starts in the same way as the single READ from current location (Figure 10). Instead of generating a no-acknowledge bit after the first byte of data Previous Reg Address, N S Slave Address 1 A N+1 Read Data A N+2 Read Data A N+L-1 Read Data A N+L Read Data A P Figure 12. Sequential READ, Start from Current Location Single WRITE to Random Location then LOW bytes of the register address that is to be written. The master follows this with the byte of write data. The WRITE is terminated by the master generating a stop condition. This sequence (Figure 13) begins with the master generating a start condition. The slave address/data direction byte signals a WRITE and is followed by the HIGH Previous Reg Address, N S Slave Address 0 A Reg Address[15:8] Reg Address, M A A Reg Address[7:0] M+1 A A Write Data P Figure 13. Single WRITE to Random Location Sequential WRITE, Start at Random Location has been transferred, the master generates an acknowledge bit and continues to perform byte WRITEs until "L" bytes have been written. The WRITE is terminated by the master generating a stop condition. This sequence (Figure 14) starts in the same way as the single WRITE to random location (Figure 13). Instead of generating a no-acknowledge bit after the first byte of data Previous Reg Address, N S Slave Address 0 A M+1 Write Data Reg Address[15:8] A M+2 A Write Data Reg Address, M Reg Address[7:0] M+3 A Write Data M+L-2 A Write Data 13 A M+L-1 A Figure 14. Sequential WRITE, Start at Random Location www.onsemi.com M+1 Write Data M+L A A P AR0833 REGISTERS The AR0833 provides a 16-bit register address space accessed through a serial interface ("Two-Wire Serial Register Interface"). Each register location is 8 or 16 bits in size. The address space is divided into the five major regions shown in Table 9. The remainder of this section describes these registers in detail. Table 9. ADDRESS SPACE REGIONS Address Range Description 0x0000-0x0FFF Configuration registers (read-only and read-write dynamic registers) 0x1000-0x1FFF Parameter limit registers (read-only static registers) 0x2000-0x2FFF Image statistics registers (none currently defined) 0x3000-0x3FFF Manufacturer-specific registers (read-only and read-write dynamic registers) Register Notation Byte Ordering Registers that occupy more than one byte of address space are shown with the lowest address in the highest-order byte lane to match the byte-ordering on the data bus. For example, the chip_version_reg register is R0x0000-1. In the register table the default value is shown as 0x4B00. This means that a read from address 0x0000 would return 0x4B, and a read from address 0x0001 would return 0x00. When reading this register as two 8-bit transfers on the serial interface, the 0x4B will appear on the serial interface first, followed by the 0x00. The underlying mechanism for reading and writing registers provides byte write capability. However, it is convenient to consider some registers as multiple adjacent bytes. The AR0833 uses 8-bit, 16-bit, and 32-bit registers, all implemented as 1 or more bytes at naturally aligned, contiguous locations in the address space. In this document, registers are described either by address or by name. When registers are described by address, the size of the registers is explicit. For example, R0x3024 is a 2-bit register at address 0x3024, and R0x3000-1 is a 16-bit register at address 0x3000-0x3001. When registers are described by name, the size of the register is implicit. It is necessary to refer to the register table to determine that model_id is a 16-bit register. Address Alignment All register addresses are aligned naturally. Registers that occupy 2 bytes of address space are aligned to even 16-bit addresses, and registers that occupy 4 bytes of address space are aligned to 16-bit addresses that are an integer multiple of 4. Register Aliases A consequence of the internal architecture of the AR0833 is that some registers are decoded at multiple addresses. Some registers in "configuration space" are also decoded in "manufacturer-specific space." To provide unique names for all registers, the name of the register within manufacturer-specific register space has a trailing underscore. For example, R0x0202 is coarse_integration_time and R0x3012 is coarse_integration_time_. The effect of reading or writing a register through any of its aliases is identical. Bit Representation For clarity, 32-bit hex numbers are shown with an underscore between the upper and lower 16 bits. For example: 0x3000_01AB. Data Format Most registers represent an unsigned binary value or set of bit fields. For all other register formats, the format is stated explicitly at the start of the register description. The notation for these formats is shown in Table 10. Bit Fields Some registers provide control of several different pieces of related functionality, and this makes it necessary to refer to bit fields within registers. As an example of the notation used for this, the least significant 4 bits of the chip_version_reg register are referred to as chip_version_reg[3:0] or R0x0000-1[3:0]. Bit Field Aliases In addition to the register aliases described above, some register fields are aliased in multiple places. For example, R0x0100 (mode_select) has only one operational bit, R0x0100[0]. This bit is aliased to R0x301A-B[2]. The effect of reading or writing a bit field through any of its aliases is identical. www.onsemi.com 14 AR0833 Table 10. DATA FORMATS Name FIX16 Description Signed fixed-point, 16-bit number: two's complement number, 8 fractional bits. Examples: 0x0100 = 1.0 0x8000 = -128 0xFFFF = -0.0039065 UFIX16 Unsigned fixed-point, 16-bit number: 8.8 format. Examples: 0x0100 = 1.0 0x280 = 2.5 FLP32 Signed floating-point, 32-bit number: IEEE 754 format. Example: 0x4280_0000 = 64.0 Register Behavior behavior until the next frame start. However, the frame that would be read out at that frame start will have been integrated using the old row width, so reading it out using the new row width would result in a frame with an incorrect integration time. By default, bad frames are masked. If the masked bad frame option is enabled, both LV and FV are inhibited for these frames so that the vertical blanking time between frames is extended by the frame time. In the register tables, the "Bad Frame" column shows where changing a register or register field will cause a bad frame. This notation is used: * N - No. Changing the register value will not produce a bad frame. * Y - Yes. Changing the register value might produce a bad frame. * YM - Yes; but the bad frame will be masked out when mask_corrupted_frames (R0x301A[9]) is set to "1." Registers vary from "read-only," "read/write," and "read, write-1-to-clear." Double-Buffered Registers Some sensor settings cannot be changed during frame readout. For example, changing R0x3004-5 (x_addr_start) partway through frame readout would result in inconsistent row lengths within a frame. To avoid this, the AR0833 double-buffers many registers by implementing a "pending" and a "live" version. Reads and writes access the pending register. The live register controls the sensor operation. The value in the pending register is transferred to a live register at a fixed point in the frame timing, called frame start. Frame start is defined as the point at which the first dark row is read out internally to the sensor. In the register tables the "Frame Sync'd" column shows which registers or register fields are double-buffered in this way. Using grouped_parameter_hold Register grouped_parameter_hold (R0x301A[15]) can be used to inhibit transfers from the pending to the live registers. When the AR0833 is in streaming mode, this register should be written to "1" before making changes to any group of registers where a set of changes is required to take effect simultaneously. When this register is written to "0," all transfers from pending to live registers take place on the next frame start. An example of the consequences of failing to set this bit follows: * An external auto exposure algorithm might want to change both gain and integration time between two frames. If the next frame starts between these operations, it will have the new gain, but not the new integration time, which would return a frame with the wrong brightness that might lead to a feedback loop with the AE algorithm resulting in flickering. Changes to Integration Time If the integration time is changed while FV is asserted for frame n, the first frame output using the new integration time is frame (n + 2). The sequence is as follows: 1. During frame n, the new integration time is held in the pending register. 2. At the start of frame (n + 1), the new integration time is transferred to the live register. Integration for each row of frame (n + 1) has been completed using the old integration time. 3. The earliest time that a row can start integrating using the new integration time is immediately after that row has been read for frame (n + 1). The actual time that rows start integrating using the new integration time is dependent upon the new value of the integration time. 4. When frame (n + 2) is read out, it will have been integrated using the new integration time. Bad Frames A bad frame is a frame where all rows do not have the same integration time or where offsets to the pixel values have changed during the frame. Many changes to the sensor register settings can cause a bad frame. For example, when line_length_pck (R0x300C) is changed, the new register value does not affect sensor If the integration time is changed on successive frames, each value written will be applied for a single frame; the latency between writing a value and it affecting the frame readout remains at two frames. www.onsemi.com 15 AR0833 CLOCKING Default setup gives a physical 73.2 MHz internal clock for an external input clock of 24 MHz. The sensor contains a phase-locked loop (PLL) for timing generation and control. The PLL contains a prescaler to divide the input clock applied on EXTCLK, a VCO to multiply the prescaler output, and a set of dividers to generate the output clocks. The PLL structure is shown in Figure 15. Changes to Gain Settings Usually, when the gain settings are changed, the gain is updated on the next frame start. When the integration time and the gain are changed at the same time, the gain update is held off by one frame so that the first frame output with the new integration time also has the new gain applied. In this case, a new gain should not be set during the extra frame delay. There is an option to turn off the extra frame delay by setting extra_delay (R0x3018). row_speed (R0x3016[2:0]) PLL vt_pix_clk_div (R0x300) clk_pixel Divider vt_sys_clk_div (R0x302) PLL input clock pll_ip_clk_freq (4-24 MHz) External input clock ext_clk_freq_mhz EXTCLK vt sys clk Divider PLL internal VCO frequency vt pix clk Divider clk_pixel vt_pix_clk vt_sys_clk PLL Multiplier (m) Pre PLL Divider (n +1) pre_pll_clk_div (R0x304) op_sys_clk op sys clk Divider pll _multiplier (R0x306) op_sys_clk_div (R0x30A) op pix clk Divider op_pix_clk clk _op Divider clk_op op_pix_clk_div (R0x308) row_speed (R0x3016[10:8]) Figure 15. Clocking Configuration Figure 15 shows the different clocks and the names of the registers that contain or are used to control their values. The vt_pix_clk is divided by two to compensate for the fact that the design has 2 digital data paths. This divider should always remain turned on. AR0833 has 10-to-8 and 10-to-6 compression. The Framer IP packs two 6-bit pixels into one 12-bit data and sends it to Physical Layer. The Framer takes the action to divide word clock into half speed. The word clock should be divided by 6 from VCO at PLL in order to match Physical Layer considering one data having 12 bit-clocks. The usage of the output clocks is shown below: * clk_pixel (vt_pix_clk / row_speed[2:0]) is used by the sensor core to readout and control the timing of the pixel_clock_mhz + * * pixel array. The sensor core produces one 10-bit pixel each vt_pix_clk period. The line length (line_length_pck) is controlled in increments of the clk_pixel period. clk_op (op_pix_clk / row_speed[10:8]) is used to load parallel pixel data from the output FIFO (see Figure 40) to the serializer. The output FIFO generates one pixel each op_pix_clk period. op_sys_clk is used to generate the serial data stream on the output. The relationship between this clock frequency and the op_pix_clk frequency is dependent upon the output data format. The pixel frequency can be calculated in general as: ext_clk_freq_mhz pre_pll_clk_div vt_sys_clk_div 2 pll_multiplier vt_pix_clk_div row_speed[2:0] (eq. 1) The output clock frequency can be calculated as: clk_op_freq_mhz + ext_clk_freq_mhz pre_pll_clk_div op_sys_clk_div op_sys_clk_freq_mhz + pll_multiplier op_pix_clk_div ext_clk_freq_mhz pre_pll_clk_div www.onsemi.com 16 pll_multiplier op_sys_clk_div row_speed[10:8] (eq. 2) (eq. 3) AR0833 PLL Clocking When the AR0833 enters a soft standby state, almost all of the internal clocks are stopped. The only exception is that a small amount of logic is clocked so that the two-wire serial interface continues to respond to read and write requests. The PLL divisors should be programmed while the AR0833 is in the software standby state. After programming the divisors, it is necessary to wait for the VCO lock time before enabling the PLL. The PLL is enabled by entering the streaming state. An external timer will need to delay the entrance of the streaming mode by 1 millisecond so that the PLL can lock. The effect of programming the PLL divisors while the AR0833 is in the streaming state is undefined. FEATURES Interlaced HDR Readout The sensor enables HDR by outputting frames where even and odd row pairs within a single frame are captured at different integration times. This output is then matched with an algorithm designed to reconstruct this output into an HDR still image or video. The sensor HDR is controlled by two shutter pointers (Shutter pointer1, Shutter pointer2) that control the integration of the odd (Shutter pointer1) and even (Shutter pointer 2) row pairs. Clock Control The AR0833 uses an aggressive clock-gating methodology to reduce power consumption. The clocked logic is divided into a number of separate domains, each of which is only clocked when required. I-FRAME 1 Shutter Pointer 1 EXPOSURE I-FRAME 1 Tint 1 I-FRAME 2 Shutter Pointer 2 Sample Pointer EXPOSURE I-FRAME 1 Output Frame from Sensor Tint 2 Output I-FRAME 1 and 2 Figure 16. HDR Integration Time www.onsemi.com 17 AR0833 INTEGRATION TIME FOR INTERLACED HDR READOUT Tint1 (Integration Time 1) and Tint2 (Integration Time 2) The limits for the coarse integration time are defined by: coarse_integration_time_min v coarse_integration_time v (frame_length_lines * coarse_integration_time_max_margin) (eq. 4) coarse_integration_time2_min v coarse_integration_time2 v (frame_length_lines * coarse_integration_time2_max_margin) (eq. 5) The actual integration time is given by: integration_time + integration_time2 + coarse_integration_time line_length_pck 10 6 vt_pix_clk_freq_mhz coarse_integration_time2 line_length_pck vt_pix_clk_freq_mhz 10 6 (eq. 6) (eq. 7) Bayer Resampler If this limit is broken, the frame time will automatically be extended to (coarse_integration_time + coarse_ integration_time_max_margin) to accommodate the larger integration time. The ratio between even and odd rows is typically adjusted to 1x, 2x, 4x, and 8x. The imaging artifacts found from a 2 x 2 binning or summing will show image artifacts from aliasing. These can be corrected by resampling the sampled pixels in order to filter these artifacts. Figure 17 shows the pixel location resulting from 2 x 2 summing or binning located in the middle and the resulting pixel locations after the Bayer re-sampling function has been applied. Figure 17. Bayer Resampling designed to be used with modes configured with 2 x 2 binning or summing. The feature will not remove aliasing artifacts that are caused skipping pixels. The improvements from using the Bayer resampling feature can be seen in Figure 18. In this example, image edges seen on a diagonal have smoother edges when the Bayer re-sampling feature is applied. This feature is only 2 x 2 Binned - Before 2 x 2 Binned - After Resampling Figure 18. Results of Resampling www.onsemi.com 18 AR0833 To enable the Bayer resampling feature: 1. Set R0x400 = 2 // Enable the on-chip scalar. 2. Set R0x306E to 0x90B0 // Configure the on-chip scalar to resample Bayer data. NOTE: The image readout (rows and columns) has to have two extra rows and two extra columns when using the resample feature. To disable the Bayer resampling feature: 1. Set R0x400 = 0 // Disable the on-chip scalar. 2. Set R0x306E to 0x9080 // Configure the on-chip scalar to resample Bayer data. Image Array Readout 3264 x 2448 2 x 2 Binning Image Size Output 1632 x 1224 Resampling Resampled Image Output 1632 x 1224 Figure 19. Illustration of Resampling Operation One-Time Programmable Memory (OTPM) DVDD_1V2_PHY, and DVDD_1V8). VAA must be set to 2.8 V during the programming process. VPP must be initially floating. All other supplies must be at their nominal voltage. 2. Provide a 12-MHz EXTCLK clock input. 3. Set R0x301A = 0x18, to put sensor in the soft standby mode. 4. Set R0x3130 = 0xFF01 (Timing configuration) 5. Set R0x304C[15:8] = Record type (E.g. 0x30) 6. Set R0x304C[7:0] = Length of the record which is the number of OTPM data registers that are filled in. 7. Set R0x3054[9] = 0 to ensure that the error checking and correction is enabled. 8. Write data into all the OTPM data registers: R0x3800-R0x39FE. 9. Ramp up VPP to 6.5 V. 10. Set the otpm_control_auto_wr_start bit in the otpm_control register R0x304A[0] = 1, to initiate the auto program sequence. The sensor will now program the data into the OTPM. 11. Poll otpm_control_auto_wr_end (R0x304A [1]) to determine when the sensor is finished programming the word. 12. Verify that the otpm_control_auto_wr_ success(0x304A[2]) bit is set. 13. If the above bits are not set to 1, then examine otpm_status register R0x304E[9] to verify if the OTPM memory is full and 0x304E[10] to verify if OTPM memory is insufficient. 14. Remove the high voltage (VPP) and float VPP pin. The AR0833 features 5.6 Kb of one-time programmable memory (OTPM) for storing shading correction coefficients, individual module, and customer-specific information. The user may program the data before shipping. OTPM can be accessed through two-wire serial interface. The AR0833 uses the auto mode for fast OTPM programming and read operations. To read out the OTPM, 1.8 V supply is required. As a result, a dedicated DVDD_1V8 pad has been implemented.During the programming process, a dedicated pin for high voltage needs to be provided to perform the anti-fusing operation. This voltage (VPP) would need to be 6.5 V. The completion of the programming process will be communicated by a register through the two-wire serial interface. If the VPP pin does not need to be bonded out as a pin on the module, it should be left floating inside the module. The programming of the OTPM requires the sensor to be fully powered and remain in software standby with its clock input applied. The information will be programmed through the use of the two-wire serial interface, and once the data is written to an internal register, the programming host machine will apply a high voltage to the programming pin, and send a program command to initiate the anti-fusing process. After the sensor has finished programming the OTPM, a status bit will be set to indicate the end of the programming cycle, and the host machine can poll the setting of the status bit through the two-wire serial interface. Only one programming cycle for the 16-bit word can be performed. Reading the OTPM data requires the sensor to be fully powered and operational with its clock input applied. The data can be read through a register from the two-wire serial interface. Reading the OTPM 1. Apply power to all the power rails of the sensor (VDD_IO, VAA, VAA_PIX, DVDD_1V2, DVDD_1V2_PHY, and DVDD_1V8) at their nominal voltage. 2. Set EXTCLK to normal operating frequency. 3. Perform proper reset sequence to the sensor. 4. Set R0x3134 = 0xCD95 (Timing Configuration) Programming and Verifying the OTPM The procedure for programming and verifying the AR0833 OTPM follows: 1. Apply power to all the power rails of the sensor (VDD_IO, VAA, VAA_PIX, DVDD_1V2, www.onsemi.com 19 AR0833 2. Global reset release (GRR) mode. his mode can be used to acquire a single image at the current resolution. In this mode, the end point of the pixel integration time is controlled by an external electromechanical shutter, and the AR0833 provides control signals to interface to that shutter. The operation of this mode is described in detail in "Global Reset Release (GRR)". 5. Set R0x304C[15:8] = Record Type (for example, 0x30) 6. Set R0x304C[7:0] = Length of the record which is the number of data registers to be read back. This could be set to 0 during OTPM auto read if length is unknown. 7. Set R0x3054 = 0x0400 8. Initiate the auto read sequence by setting the otpm_control_auto_read_start bit (R0x304A[4]) = 1. 9. Poll the otpm_control_auto_rd_end bit (R0x304A[5]) to determine when the sensor is finished reading the word(s). When this bit becomes 1, the otpm_control_auto_rd_success bit (R0x304A[6]) will indicate whether the memory was read successfully or not. 10. Data can now be read back from the otpm_data registers (R0x3800-R0x39FE). The benefit for the use of an external electromechanical shutter is that it eliminates the visual artifacts associated with ERS operation. Visual artifacts arise in ERS operation, particularly at low frame rates, because an ERS image effectively integrates each row of the pixel array at a different point in time. Window Control The sequencing of the pixel array is controlled by the x_addr_start, y_addr_start, x_addr_end, and y_addr_end registers. The output image size is controlled by the x_output_size and y_output_size registers. Image Acquisition Modes The AR0833 supports two image acquisition modes: 1. Electronic rolling shutter (ERS) mode. This is the normal mode of operation. When the AR0833 is streaming, it generates frames at a fixed rate, and each frame is integrated (exposed) using the ERS. When the ERS is in use, timing and control logic within the sensor sequences through the rows of the array, resetting and then reading each row in turn. In the time interval between resetting a row and subsequently reading that row, the pixels in the row integrate incident light. The integration (exposure) time is controlled by varying the time between row reset and row readout. For each row in a frame, the time between row reset and row readout is fixed, leading to a uniform integration time across the frame. When the integration time is changed (by using the two-wire serial interface to change register settings), the timing and control logic controls the transition from old to new integration time in such a way that the stream of output frames from the AR0833 switches cleanly from the old integration time to the new while only generating frames with uniform integration. See "Changes to Integration Time". Pixel Border The default settings of the sensor provide a 3264 (H) x 2448 (V) image. A border of up to 8 pixels (4 in binning) on each edge can be enabled by reprogramming the x_addr_start, y_addr_start, x_addr_end, y_addr_end, x_output_size, and y_output_size registers accordingly. These border pixels can be used but are disabled by default. Readout Modes Horizontal Mirror The horizontal_mirror bit in the image_orientation register is set by default. The result of this is that the order of pixel readout within a row is reversed, so that readout starts from x_addr_end and ends at x_addr_start. Figure 20 shows a sequence of 6 pixels being read out with horizontal_mirror = 0 and horizontal_mirror = 1. Changing horizontal_mirror causes the Bayer order of the output image to change; the new Bayer order is reflected in the value of the pixel_order register. LINE_VALID horizontal_mirror = 0 DOUT[9:0] horizontal_mirror = 1 DOUT[9:0] G0[9:0] R0[9:0] G1[9:0] R1[9:0] G2[9:0] R2[9:0] R2[9:0] G2[9:0] R1[9:0] G1[9:0] R0[9:0] G0[9:0] Figure 20. Effect of horizontal_mirror on Readout Order www.onsemi.com 20 AR0833 Vertical Flip When the vertical_flip bit is set in the image_orientation register, the order in which pixel rows are read out is reversed, so that row readout starts from y_addr_end and ends at y_addr_start. Figure 21 shows a sequence of 6 rows being read out with vertical_flip = 0 and vertical_flip = 1. Changing vertical_flip causes the Bayer order of the output image to change; the new Bayer order is reflected in the value of the pixel_order register. FRAME_VALID vertical_flip = 0 DOUT[9:0] Row0[9:0] Row1[9:0] Row2[9:0] Row3[9:0] Row4[9:0] Row5[9:0] vertical_flip = 1 DOUT[9:0] Row5[9:0] Row4[9:0] Row3[9:0] Row2[9:0] Row1[9:0] Row0[9:0] Figure 21. Effect of vertical_flip on Readout Order Subsampling The AR0833 supports subsampling to reduce the amount of data processed by the signal chains in the AR0833, thereby allowing the frame rate to be increased and power consumption reduced. Subsampling is enabled by setting x_odd_inc and/or y_odd_inc. Values of 1, 3, and 7 can be supported. Setting both of these variables to 3 reduces the amount of row and column data processed and is equivalent to the 2 x 2 skipping readout mode provided by the AR0833. Setting x_odd_inc = 3 and y_odd_inc = 3 results in a quarter reduction in output image size. Figure 22 shows a sequence of 8 columns being read out with x_odd_inc = 3 and y_odd_inc = 1. LINE_VALID x_odd_inc = 1 DOUT[9:0] G0[9:0] R0[9:0] G1[9:0] R1[9:0] G0[9:0] R0[9:0] G2[9:0] R2[9:0] G2[9:0] R2[9:0] G3[9:0] R3[9:0] LINE_VALID x_odd_inc = 3 DOUT[9:0] Figure 22. Effect of x_odd_inc = 3 on Readout Sequence A 1/16 reduction in resolution is achieved by setting both x_odd_inc and y_odd_inc to 7. This is equivalent to 4 x 4 skipping readout mode provided by the AR0833. Figure 23 shows a sequence of 16 columns being read out with x_odd_inc = 7 and y_odd_inc = 1. LINE_VALID x_odd_inc = 1 DOUT[9:0] G0[9:0] R0[9:0] G1[9:0] R1[9:0] G0[9:0] R0[9:0] G4[9:0] R4[9:0] G2[9:0] ... G7[9:0] R7[9:0] LINE_VALID x_odd_inc = 7 DOUT[9:0] Figure 23. Effect of x_odd_inc = 7 on Readout Sequence www.onsemi.com 21 AR0833 The effect of the different subsampling settings on the pixel array readout is shown in Figure 24 through Figure 26. Y incrementing X incrementing Y incrementing X incrementing Figure 24. Pixel Readout (No Subsampling) Figure 25. Skip2 Pixel Readout (x_odd_inc = 3, y_odd_inc = 3) Y incrementing X incrementing Figure 26. Skip4 Pixel Readout (x_odd_inc = 7, y_odd_inc = 7) www.onsemi.com 22 AR0833 * (x_addr_end - x_addr_start + x_odd_inc) should be a Programming Restrictions when Subsampling When subsampling is enabled and the sensor is switched back and forth between full resolution and subsampling, ON Semiconductor recommends that line_length_pck be kept constant between the two modes. This allows the same integration times to be used in each mode. When subsampling is enabled, it may be necessary to adjust the x_addr_start, x_addr_end, y_addr_start, and y_addr_end settings: the values for these registers are required to correspond with rows/columns that form part of the subsampling sequence. The adjustment should be made in accordance with these rules: x_skip_factor = (x_odd_inc + 1) / 2 y_skip_factor = (y_odd_inc + 1) / 2 * multiple of x_skip_factor x 4 (y_addr_end - y_addr_start + y_odd_inc) should be a multiple of y_skip_factor x 4 The number of columns/rows read out with subsampling can be found from the equation below: * columns/rows = (addr_end - addr_start + odd_inc) / skip_factor Table 11 shows the row or column address sequencing for normal and subsampled readout. In the 2X skip case, there are two possible subsampling sequences (because the subsampling sequence only reads half of the pixels) depending upon the alignment of the start address. Similarly, there will be four possible subsampling sequences in the 4X skip case (though only the first two are shown in Table 11). * x_addr_start should be a multiple of x_skip_factor x 4 Table 11. ROW ADDRESS SEQUENCING DURING SUBSAMPLING odd_inc = 1 (Normal) odd_inc = 3 (2y Skip) odd_inc = 7 (4y Skip) Start = 0 Start = 0 Start = 0 0 0 0 1 1 1 2 3 4 4 5 5 6 7 8 8 8 9 9 9 10 11 12 12 13 13 14 15 Binning The AR0833 supports 2 x 1 (column binning, also called x-binning). Binning has many of the same characteristics as skipping, but because it gathers image data from all pixels in the active window (rather than a subset of them), it achieves superior image quality and avoids the aliasing artifacts that can be a characteristic side effect of skipping. Binning is enabled by selecting the appropriate subsampling settings (in read_mode, the sub-register x_odd_inc = 3 and y_odd_inc = 1 for x-binning and setting the appropriate binning bit in read_mode R0x3040[11] = 1 for x_bin_enable). As with skipping, x_addr_end and y_addr_end may require adjustment when binning is enabled. It is the first of the two columns/rows binned together that should be the end column/row in binning, so the requirements to the end address are exactly the same as in skipping mode. The effect of the different binning is shown in Figure 27 below and Figure 28. Binning can also be enabled when the 4X subsampling mode is enabled (x_odd_inc = 7 and y_odd_inc = 1 for x-binning, x_odd_inc = 7 and y_odd_inc = 7 for 4X xy-binning). In this mode, however, not all pixels will be used so this is not a 4X binning implementation. An implementation providing a combination of skip2 and bin2 is used to achieve 4X subsampling with better image quality. The effect of this subsampling mode is shown in Figure 28. www.onsemi.com 23 AR0833 Y Incrementing X Incrementing Figure 27. Bin2 Pixel Readout (x_odd_inc = 3, y_odd_inc = 1, x_bin = 1) Y Incrementing X Incrementing Figure 28. Bin2 Pixel Readout (x_odd_inc = 3, y_odd_inc = 3, x_bin = 1) www.onsemi.com 24 AR0833 Binning address sequencing is a bit more complicated than during subsampling only, because of the implementation of the binning itself. For a given column n, there is only one other column, n_bin, that can be binned with, because of physical limitations in the column readout circuitry. The possible address sequences are shown in Table 12. Table 12. COLUMN ADDRESS SEQUENCING DURING BINNING odd_inc = 1 (Normal) odd_inc = 3 (2y Bin) odd_inc = 7 (2y Skip + 2y Bin) x_addr_start = 0 x_addr_start = 0 x_addr_start = 0 0 0/2 0/4 1 1/3 1/5 2 3 4 4/6 5 5/7 6 7 8 8/10 8/12 9 9/11 9/13 10 11 12 12/14 13 13/15 14 15 There are no physical limitations on what can be binned together in the row direction. A given row n will always be binned with row n+2 in 2X subsampling mode and with row n+4 in 4X subsampling mode. Therefore, which rows get binned together depends upon the alignment of y_addr_start. The possible sequences are shown in Table 13. Table 13. ROW ADDRESS SEQUENCING DURING BINNING odd_inc = 1 (Normal) odd_inc = 3 (2y Bin) odd_inc = 7 (2y Skip + 2y Bin) y_addr_start = 0 y_addr_start = 0 y_addr_start = 0 0 0/2 0/4 1 1/3 1/5 2 3 4 4/6 5 5/7 6 7 8 8/10 8/12 9 9/11 9/13 10 11 12 12/14 13 13/15 14 15 www.onsemi.com 25 AR0833 4. XbinYsum R0x3040[11], x_bin_en: 1 R0x3040[13], row_sum: 1 R0x0382: x_odd_inc = 3 (xbin2) R0x0386: y_odd_inc = 3 (ysum2) 5. XsumYsum R0x3040[11], x_bin_en: 1 R0x3040[13], row_sum: 1 R0x3EE4[0], sreg_colamp_sum2: 1 (cannot write to this bit when streaming - have to write to entire register) R0x0382: x_odd_inc = 3 (xsum2) R0x0386: y_odd_inc = 3 (ysum2) Programming Restrictions When Binning and Summing Binning and summing require different sequencing of the pixel array and impose different timing limits on the operation of the sensor. As a result, when xy-subsampling is enabled, some of the programming limits declared in the parameter limit registers are no longer valid. In addition, the default values for some of the manufacturer-specific registers need to be reprogrammed. See "Minimum Frame Time" and "Minimum Row Time". Subsampling/Binning Options: 1. XskipYskip R0x3040[11], x_bin_en: 0 R0x3040[13], row_sum: 0 R0x0382: x_odd_inc = 3 (xskip2) or 7 (xskip4) R0x0386: y_odd_inc = 3 (yskip2), 7 (yskip4) or 15 (yskip8) 2. XbinYskip R0x3040[11], x_bin_en: 1 R0x3040[13], row_sum: 0 R0x0382: x_odd_inc = 3 (xbin2) R0x0386: y_odd_inc = 3 (yskip2), 7 (yskip4) or 15 (yskip8) 3. XskipYsum R0x3040[11], x_bin_en: 0 R0x3040[13], row_sum: 1 R0x0382: x_odd_inc = 3 (xskip2) or 7 (xskip4) R0x0386: y_odd_inc = 3 (ysum2) 2 y 2 Binning or Summing Binning, Skipping, and Summing Mode Summing, skipping, and binning can be combined in the modes listed in Table 14. Unlike binning mode where the values of adjacent same color pixels are averaged together, summing adds the pixel values together resulting in better sensor sensitivity. Summing is supposed to provide two times the sensitivity compared to the binning only mode. Table 14. AVAILABLE SKIP, BIN, AND SUM MODES IN THE AR0833 SENSOR Subsampling Method Horizontal Vertical Skipping 2x, 4x 2x, 4x, 8x Binning 2x Summing 2x X-binning 2x Summing Avg Sh Sv Avg Figure 29. Pixel Binning and Summing www.onsemi.com 26 Sv Sh AR0833 * m, which is adjustable with register R0x0404 * Legal values for m are 16 through 96, giving the user Scaler Scaling reduces the size of the output image while maintaining the same field-of-view. The input and output of the scaler is in Bayer format. When compared to skipping, scaling is advantageous as it avoids aliasing. The scaling factor, programmable in 1/16 steps, is used for horizontal and vertical scalers. The AR0833 sensor is capable of horizontal scaling and full (horizontal and vertical) scaling. The scale factor is determined by: * n, which is fixed at 16 minimum line_length_pck + the ability to scale from 1:1 (m = 16) to 1:6 (m = 96) Frame Rate Control The formulas for calculating the frame rate of the AR0833 are shown below. The line length is programmed directly in pixel clock periods through register line_length_pck. For a specific window size, the minimum line length can be found from Equation 8: x_addr_end * x_addr_start ) 1 subsampling factor Note that line_length_pck also needs to meet the minimum line length requirement set in register min_line_length_pck. The row time can either be limited by the time it takes to sample and reset the pixel array for each row, or by the time it takes to sample and read out a row. Values for min_line_blanking_pck are provided in "Minimum Row Time". minimum frame_length_lines + ) min_line_blanking_pck (eq. 8) The frame length is programmed directly in number of lines in the register frame_line_length. For a specific window size, the minimum frame length can be found in Equation 9: y_addr_end * y_addr_start ) 1 subsampling factor ) min_frame_blanking_lines (eq. 9) The frame rate can be calculated from these variables and the pixel clock speed as shown in Equation 10: frame rate + vt_pixel_clock_mhz line_length_pck 10 6 1 (eq. 10) frame_length_lines Minimum Frame Time If coarse_integration_time is set larger than frame_length_lines the frame size will be expanded to coarse_integration_time + 1. The minimum number of rows in the image is 1, so min_frame_length_lines will always equal (min_frame _blanking_lines + 1). Minimum Row Time Enough time must be given to the output FIFO so it can output all data at the set frequency within one row time. There are therefore two checks that must all be met when programming line_length_pck: * line_length_pck min_line_length_pck in Table 15 * The row time must allow the FIFO to output all data during each row. That is, line_length_pck (x_output_size x 2 + 0x005E) x "vt_pix_clk period" / "op_pix_clk period" Table 15. MINIMUM FRAME TIME AND BLANKING NUMBERS min_frame_blanking_lines 0x008F min_frame_length_lines 0x0A1F Integration Time The integration (exposure) time of the AR0833 is controlled by the coarse_integration_time register. The limits for the coarse integration time are defined by: coarse_integration_time_min v coarse_integration_time (eq. 11) The actual integration time is given by: integration_time + coarse_integration_time line_length_pck vt_pix_clk_freq_mhz 10 6 (eq. 12) It is required that: coarse_integration_time v (frame_length_lines * coarse_integration_time_max_margin) (eq. 13) In binning mode, frame_length_lines should be set larger than coarse_integration_time by at least 3 to avoid column imbalance artifact. If this limit is broken, the frame time will automatically be extended to (coarse_integration_time + coarse_integartion_ time_max_margin) to accommodate the larger integration time. www.onsemi.com 27 AR0833 Flash Timing Control Enabling the LED flash will cause one bad frame, where several of the rows only have the flash on for part of their integration time. This can be avoided either by first enabling mask bad frames (R0x301A[9] = 1) before the enabling the flash or by forcing a restart (R0x301A[1] = 1) immediately after enabling the flash; the first bad frame will then be masked out, as shown in Figure 31. Read-only bit flash[14] is set during frames that are correctly integrated; the state of this bit is shown in Figures 30 and Figure 31. The AR0833 supports both xenon and LED flash timing through the FLASH output signal. The timing of the FLASH signal with the default settings is shown in Figure 30 (xenon) and Figure 31 (LED). The flash and flash_count registers allow the timing of the flash to be changed. The flash can be programmed to fire only once, delayed by a few frames when asserted, and (for xenon flash) the flash duration can be programmed. FRAME_VALID Flash STROBE State of Triggered Bit (R0x3046-7[14]) Figure 30. Xenon Flash Enabled FRAME_VALID Flash STROBE State of Triggered Bit (R0x3046-7[14]) Flash Enabled during this Frame NOTE: Bad Frame is Masked Good Frame Good Frame Bad Frame is Masked Flash Disabled during this Frame An option to invert the flash output signal through R0x3046[7] is also available. Figure 31. LED Flash Enabled Global Reset Release (GRR) 4. All of the rows of the pixel array are taken out of reset simultaneously. All rows start to integrate incident light. The electromechanical shutter may be open or closed at this time. 5. If the electromechanical shutter has been closed, it is opened. 6. After the desired integration time (controlled internally or externally to the AR0833), the electromechanical shutter is closed. 7. A single output frame is generated by the sensor with the usual LV, FV, PIXCLK, and DOUT timing. As soon as the output frame has completed (FV negates), the electromechanical shutter may be opened again. 8. The sensor automatically resumes operation in ERS mode. Global reset release mode allows the integration time of the AR0833 to be controlled by an external electromechanical shutter. GRR mode is generally used in conjunction with ERS mode. The ERS mode is used to provide viewfinder information, the sensor is switched into GRR mode to capture a single frame, and the sensor is then returned to ERS mode to restore viewfinder operation. Overview of Global Reset Release Sequence The basic elements of the GRR sequence are: 1. By default, the sensor operates in ERS mode and the SHUTTER output signal is LOW. The electromechanical shutter must be open to allow light to fall on the pixel array. Integration time is controlled by the coarse_integration_time register. 2. A global reset sequence is triggered. 3. All of the rows of the pixel array are placed in reset. This sequence is shown in Figure 32. The following sections expand to show how the timing of this sequence is controlled. www.onsemi.com 28 AR0833 ERS Row Reset Integration Readout ERS Figure 32. Overview of Global Reset Sequence Entering and Leaving the Global Reset Sequence A global reset sequence can be triggered by a register write to R0x315E global_seq_trigger[0] (global trigger, to transition this bit from a 0 to a 1) or by a rising edge on a suitably-configured GPI input). When a global reset sequence is triggered, the sensor waits for the end of the current row. When LV negates for that row, FV is negated 6 PIXCLK periods later, potentially truncating the frame that was in progress. The global reset sequence completes with a frame readout. At the end of this readout phase, the sensor automatically resumes operation in ERS mode. The first frame integrated with ERS will be generated after a delay of approximately ((13 + coarse_integration_time) x line_length_pck). This sequence is shown in Figure 33. While operating in ERS mode, double-buffered registers ("Double-Buffered Registers") are updated at the start of each frame in the usual way. During the global reset sequence, double-buffered registers are updated just before the start of the readout phase. Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS Figure 33. Entering and Leaving a Global Reset Sequence pixel array to be set to the correct reset voltage level. The row reset phase takes a finite amount of time due to the capacitance of the pixel array and the capability of the internal voltage booster circuit that is used to generate the reset voltage level. As soon as the global_rst_end count has expired, all rows in the pixel array are taken out of reset simultaneously and the pixel array begins to integrate incident light. Programmable Settings The registers global_rst_end and global_read_start allow the duration of the row reset phase and the integration phase to be controlled, as shown in Figure 34. The duration of the readout phase is determined by the active image size. The recommended setting for global_rst_end is 0x3160 (for example, 512 s total reset time) with default vt_pix_clk. This allows sufficient time for all rows of the Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start Figure 34. Controlling the Reset and Integration Phases of the Global Reset Sequence point at which the shutter closes. Finally, the shutter opens again after the end of the readout phase. In shutter example 2, the shutter is open during the initial ERS sequence and closes sometime during the row reset phase. The shutter both opens and closes during the integration phase. The pixel array is integrating incident light for the part of the integration phase during which the shutter is open. As for the previous example, the shutter opens again after the end of the readout phase. Control of the Electromechanical Shutter Figure 35 shows two different ways in which a shutter can be controlled during the global reset sequence. In both cases, the maximum integration time is set by the difference between global_read_start and global_rst_end. In shutter example 1, the shutter is open during the initial ERS sequence and during the row reset phase. The shutter closes during the integration phase. The pixel array is integrating incident light from the start of the integration phase to the www.onsemi.com 29 AR0833 Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start Maximum Integration Time Actual Integration Time SHUTTER Example 1 Shutter Open (Physical) Shutter Closed Shutter Open Actual Integration Time SHUTTER Example 2 Shutter Open (Physical) Closed Shutter Open Shutter Closed Shutter Open Figure 35. Control of the Electromechanical Shutter The AR0833 provides a SHUTTER output signal to control (or help the host system control) the electromechanical shutter. The timing of the SHUTTER output is shown in Figure 36. SHUTTER is negated by default. The point at which it asserts is controlled by the programming of global_shutter_start. At the end of the global reset readout phase, SHUTTER negates approximately (2 x line_length_pck) after the negation of FV. This programming restriction must be met for correct operation: * global_read_start > global_shutter_start It is essential that the shutter remains closed during the entire row readout phase (that is, until FV has negated for the frame readout); otherwise, some rows of data will be corrupted (over-integrated). It is essential that the shutter closes before the end of the integration phase. If the row readout phase is allowed to start before the shutter closes, each row in turn will be integrated for one row-time longer than the previous row. After FV negates to signal the completion of the readout phase, there is a time delay of approximately (10 x line_length_pck) before the sensor starts to integrate light-sensitive rows for the next ERS frame. It is essential that the shutter be opened at some point in this time window; otherwise, the first ERS frame will not be uniformly integrated. Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start ~2 x line_length_pck global_shutter_start SHUTTER (Signal) Figure 36. Controlling the SHUTTER Output www.onsemi.com 30 AR0833 integration phase and will remain asserted for a time that is controlled by the value of the flash_count register. When flash_count is programmed for value N, (where N is 0-0x3FE) the resulting flash duration is given by N x 512 x (1/vt_pix_clk_freq_mhz), as shown in Figure 37. Using FLASH with Global Reset If R0x315E global_seq_trigger[2] = 1 (global flash enabled) when a global reset sequence is triggered, the FLASH output signal will be pulsed during the integration phase of the global reset sequence. The FLASH output will assert a fixed number of cycles after the start of the Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start ~2 x line_length_pck global_shutter_start SHUTTER (Fixed) flash_count FLASH Figure 37. Using FLASH with Global Reset When the flash_count = 0x3FF, the flash signal will be maximized and goes LOW when readout starts, as shown in Figure 38. This would be preferred if the latency in closing the shutter is longer than the latency for turning off the flash. This guarantees that the flash stays on while the shutter is open. Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start ~2 x line_length_pck global_shutter_start SHUTTER (Fixed) FLASH Figure 38. Extending FLASH Duration in Global Reset (Reference Readout Start) www.onsemi.com 31 AR0833 When the trigger is de-asserted to end integration, the integration phase is extended by a further time given by global_read_start - global_shutter_start. Usually this means that global_read_start should be set to global_shutter_start + 1. The operation of this mode is shown in Figure 39. The figure shows the global reset sequence being triggered by the GPI2 input, but it could be triggered by any of the GPI inputs or by the setting and subsequence clearing of the global_seq_trigger[0] under software control. The integration time of the GRR sequence is defined as: External Control of Integration Time If global_seq_trigger[1] = 1 (global bulb enabled) when a global reset sequence is triggered, the end of the integration phase is controlled by the level of trigger (global_seq_trigger[0] or the associated GPI input). This allows the integration time to be controlled directly by an input to the sensor. This operation corresponds to the shutter "B" setting on a traditional camera, where "B" originally stood for "Bulb" (the shutter setting used for synchronization with a magnesium foil flash bulb) and was later considered to stand for "Brief" (an exposure that was longer than the shutter could automatically accommodate). Integration Time + global_scale [global_read_start * global_shutter_start * global_rst_end] vt_pix_clk_freq_mhz (eq. 14) where: global_read_start + 2 16 global_shutter_start + 2 16 global_read_start2[7:0] ) global_read_start1[15:0] (eq. 15) global_shutter_start2[7:0] ) global_shutter_start1[15:0] (eq. 16) These programming restrictions must be met for correct operation of bulb exposures: * global_read_start > global_shutter_start * global_shutter_start > global_rst_end * global_shutter_start must be smaller than the exposure time (that is, this counter must expire before the trigger is de-asserted) The integration equation allows for 24-bit precision when calculating both the shutter and readout of the image. The global_rst_end has only 16-bit as the array reset function and requires a short amount of time. The integration time can also be scaled using global_scale. The variable can be set to 0-512, 1-2048, 2-128, and 3-32. Trigger Wait for End of Current Row ERS Row Reset Automatic at End of Frame Readout Integration Readout ERS global_rst_end global_read_start - global_shutter_start GPI2 Figure 39. Global Reset Bulb of the current output line). The SMIA data path limiter function (see Figure 40) attempts to extend (pad) all frames to the programmed value of y_output_size. If this padding is still in progress when the global reset readout phase starts, the SMIA data path will not detect the start of the frame correctly. Therefore, to use global reset with the serial data path, this timing scenario must be avoided. One possible way of doing this would be to synchronize (under software control) the assertion of trigger to an end-of-frame marker on the serial data stream. At the end of the readout phase of the global reset sequence, the sensor automatically resumes operation in ERS mode. Retriggering the Global Reset Sequence The trigger for the global reset sequence is edge-sensitive; the global reset sequence cannot be retriggered until the global trigger bit (in the R0x315E global_seq_trigger register) has been returned to "0," and the GPI (if any) associated with the trigger function has been negated. The earliest time that the global reset sequence can be retriggered is the point at which the SHUTTER output negates; this occurs approximately (2 x line_length_pck) after the negation of FV for the global reset readout phase. Using Global Reset with SMIA Data Path When a global reset sequence is triggered, it usually results in the frame in progress being truncated (at the end www.onsemi.com 32 AR0833 remain in streaming state until the global reset sequence (including frame readout) has completed, as shown in Figure 40. Global Reset and Soft Standby If the R0x301A[2] mode_select[stream] bit is cleared while a global reset sequence is in progress, the AR0833 will ERS Row Reset Integration Readout ERS R0x0100 mode_select[streaming] System Style Software Standby Streaming Figure 40. Entering Soft Standby During a Global Reset Sequence Slave Mode which is similar to the GRR Bulb mode. The major difference to our existing sensor is to start the GRR sequence after the end of the current frame instead of to start immediately in the next following row. Slave mode is to ensure having an ERS-GRR-ERS transition without a broken ERS frame before GRR. It requests to trigger/end the GRR sequence through the pin GRR TRIG ON Wait for VD, then Global Reset Sequence Starts Sensor Readout Sensor Readout Sensor Readout VD Sensor Starts to Read Out after VD is Inserted Figure 41. Slave Mode Transition www.onsemi.com 33 AR0833 GAIN AR0833 supports both analog and digital gain. be set by analog gain. Global gain register (R0x305E) sets the analog gain. Bits [1:0] set the colamp gain while bits [4:2] are reserved for ADC gain. While the 2-bit colamp gain provides up to 4x analog gain, only LSB (bit [2]) of ADC gain bits is utilized to support 2x ADC gain. Table 16 is the recommended gain setting: Analog Gain Analog gain is provided by colamp and ADC reference scaling (there is no ASC gain due to column parallel nature of architecture). Only global (not per-color) coarse gain can Table 16. RECOMMENDED ANALOG GAIN SETTING Colamp Gain Codes (R0x305E[1:0]) ADC Gain Codes (R0x305E[4:2]) Colamp Gain ADC Gain Total Gain 0 0 0 0 0 1 1 1 0 1 0 0 0 2 1 2 1 0 0 0 0 3 1 3 1 1 0 0 0 4 1 4 1 0 0 0 1 3 2 6 1 1 0 0 1 4 2 8 Digital Gain of 1/128. This sub-1x gain provides the fine gain control for the sensor. Digital gain provides both per-color and fine (sub 1x) gain. The analog and digital gains are multiplicative to give the total gain. Digital gain is set by setting bits R0x305E[15:5] to set global gain or by individually setting digital color gain R0x3056-C[15:5] where these 11 bits are designed in 4p7 format i.e. 4 MSB provide gain up to 15x in step of 1x while 7 LSB provide sub-1x gain with a step size Total Gain + (1 ) dec(R0x305D[1:0])) Total Gain Max. total gain required by design spec is 8x (analog) and 16x (digital) with min. step size of 1/8. The total gain equation can be formulated as: (1 ) R0x305E[2]) where X is 6, 8, A, C, for Gr, B, R and Gb, respectively. NOTE: ON Semiconductor recommends using the registers mentioned above for gain settings. Avoid R0x3028 to R0x3038 unless their mapping to above registers is well understood and taken into account. www.onsemi.com 34 dec(R0x305X[15:5]) 128 (eq. 17) AR0833 TEMPERATURE SENSOR A standalone PTAT based temperature sensor has been implemented. The block is controlled independent of sensor timing and all communication happens through the two-wire serial interface. INTERNAL VCM DRIVER The AR0833 utilizes an internal Voice Coil Motor (VCM) driver. The VCM functions are register-controlled through the serial interface. There are two output ports, VCM_ISINK and VCM_GND, which would connect directly to the AF actuator. Take precautions in the design of the power supply routing to provide a low impedance path for the ground connection. Appropriate filtering would also be required on the actuator supply. Typical values would be a 0.1 F and 10 F in parallel. VVCM VCM AR0833 10 mF VCM_ISINK VCM_GND DGND Figure 42. VCM Driver Typical Diagram Table 17. VCM DRIVER TYPICAL Characteristic Parameter Minimum Typical Maximum Unit VCM_OUT Voltage at VCM Current Sink 2.5 2.8 3.3 V WVCM Voltage at VCM Actuator 2.5 2.8 3.3 V INL Relative Accuracy - 1.5 4 LSB RES Resolution - 8 - bits DNL Differential Nonlinearity -1 - +1 LSB Output Current 90 100 110 mA Slew Rate (User Programmable) - - 13 mA/ms IVCM www.onsemi.com 35 AR0833 SPECTRAL CHARACTERISTICS 70 Red 60 Green Blue Quantum Efficiency (%) 50 40 30 20 10 0 350 400 450 500 550 Wavelength (nm) 600 650 700 750 Figure 43. Quantum Efficiency Image Height CRA vs. Image Height Plot 20 18 16 CRA (deg) 14 12 10 8 6 4 2 0 0 10 20 30 40 50 60 70 IMAGE HEIGHT (%) 80 90 Figure 44. Chief Ray Angle (CRA) vs. Image Height www.onsemi.com 36 100 110 CRA (%) (mm) 0 0 (deg) 0 5 0.143 0.77 10 0.286 1.55 15 0.428 2.33 20 0.571 3.11 25 0.714 3.87 30 0.857 4.62 35 1.000 5.36 40 1.142 6.07 45 1.285 6.77 50 1.428 7.43 55 1.571 8.06 60 1.714 8.66 65 1.856 9.22 70 1.999 9.73 75 2.142 10.19 80 2.285 10.59 85 2.428 10.93 90 2.570 11.18 95 2.713 11.34 100 2.856 11.40 AR0833 ELECTRICAL CHARACTERISTICS Table 18. Table 19 shows the timing specification for the two-wire serial interface. Two-Wire Serial Register Interface The electrical characteristics of the two-wire serial register interface (SCLK, SDATA) are shown in Figure 45 and III III III III III tF 70% 30% SDATA SCLK S EEE EEE EEE EEE EEE tSDV 70% 30% 30% 70% tACV 30% 70% 30% tSRTH 70% 30% tSDS tSDH 1st Clock 9th Clock tHIGH 70% NOTE: Sr EEIII EEIII EEIII EEIII EEIII tBUF 70% 30% 70% SDATA SCLK tR 70% 30% 70% tSRTS 70% 30% 9th Clock tLOW tSTPS 70% P S Read sequence: For an 8-bit READ, read waveforms start after WRITE command and register address are issued. Figure 45. Two-Wire Serial Bus Timing Parameters Table 18. TWO-WIRE SERIAL REGISTER INTERFACE ELECTRICAL CHARACTERISTICS (fEXTCLK = 25 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_IO = 1.8 V; VDD (Digital Core) = 1.2 V; VDD_PLL = 1.2 V; VDD_TX = 1.8 V; Output Load = 68.5 pF; TJ = 55C) Symbol Parameter Condition VIL Input LOW Voltage VIH Input HIGH Voltage IIN Input Leakage Current No Pull Up Resistor; VIN = VDD_IO or DGND VOL Output LOW Voltage At Specified 2 mA IOL Output LOW Current At Specified VOL 0.1 V CIN Input Pad Capacitance Load Capacitance CLOAD Min Typ Max Unit -0.5 - 0.3 x VDD_IO V 0.7 x VDD_IO - VDD_IO + 0.5 V 10 - 14 mA 0.11 - 0.3 V - - 6 mA - - 6 pF - - N/A pF Table 19. TWO-WIRE SERIAL INTERFACE TIMING SPECIFICATIONS (VDD = 1.7-1.9 V; VAA = 2.4 -3.1 V; Environment Temperature = -30C to 50C) Min Max Unit fSCLK SCLK Frequency Definition 100 400 kHz tHIGH SCLK High Period 0.6 - ms tLOW SCLK Low Period 1.3 - ms Symbol tSRTS START Setup Time 0.6 - ms tSRTH START Hold Time 0.6 - ms tSDS Data Setup Time 100 - ns tSDH Data Hold Time 0 - ms tSDV Data Valid Time - 0.9 ms tACV Data Valid Acknowledge Time - 0.9 ms tSTPS STOP Setup Time 0.6 - ms www.onsemi.com 37 AR0833 Table 19. TWO-WIRE SERIAL INTERFACE TIMING SPECIFICATIONS (continued) (VDD = 1.7-1.9 V; VAA = 2.4 -3.1 V; Environment Temperature = -30C to 50C) Symbol tBUF Definition Bus Free Time between STOP and START Min Max Unit 1.3 - ms tr SCLK and SDATA Rise Time - 300 ns tf SCLK and SDATA Fall Time - 300 ns EXTCLK If EXTCLK is AC-coupled to the AR0833 and the clock is stopped, the EXTCLK input to the AR0833 must be driven to ground or to VDD_IO. Failure to do this will result in excessive current consumption within the EXTCLK input receiver. The electrical characteristics of the EXTCLK input are shown in Table 20. The EXTCLK input supports an AC-coupled sine-wave input clock or a DC-coupled square-wave input clock. Table 20. ELECTRICAL CHARACTERISTICS (EXTCLK) (fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_IO = 1.8 V; DVDD_1V2 = 1.2 V, Output load = 68.5 pF; TJ = 55C) Symbol Parameter fEXTCLK1 Input Clock Frequency Condition Min Typ Max Unit PLL Enabled 6 24 27 MHz tR Input Clock Rise Slew Rate CLOAD < 20 pF - 2.883 - ns tF Input Clock Fall Slew Rate CLOAD < 20 pF - 2.687 - ns VIN_AC Input Clock Minimum Voltage Swing (AC Coupled) - 0.5 - - V (p-p) VIN_DC Input Clock Maximum Voltage Swing (DC Coupled) - - - VDD_IO + 0.5 V fCLKMAX(AC) Input Clock Signaling Frequency (Low Amplitude) VIN = VIN_AC (MIN) - - 25 MHz fCLKMAX(DC) Input Clock Signaling Frequency (Full Amplitude) VIN = VDD_IO - - 48 MHz Clock Duty Cycle - 45 50 55 % tJITTER Input Clock Jitter Cycle-to-Cycle - 545 600 ps tLOCK PLL VCO Lock Time - - 0.2 2 ms CIN Input Pad Capacitance - - 6 - pF IIH Input HIGH Leakage Current - 0 - 10 mA VIH Input HIGH Voltage 0.7 x VDD_IO - VDD_IO + 0.5 - V VIL Input LOW Voltage -0.5 - 0.3 x VDD_IO - V Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 38 AR0833 Serial Pixel Data Interface The electrical characteristics of the serial pixel data interface (CLK_P, CLK_N, DATA[4:1]_P, and DATA[4:1]_N) are shown in Table 21. Table 21. ELECTRICAL CHARACTERISTICS (SERIAL MIPI PIXEL DATA INTERFACE) Symbol VOD Parameter Min High speed transmit differential voltage 140 VCMTX High speed transmit static common-mode voltage 150 VOD VOD mismatch when output is Differential-1 or Differential-0 ZOS ZOS VCMTX(L,F) Typ 200 Max Unit 270 mV 250 mV <10 Single ended output impedance 40 50 mV 62.5 Single ended output impedance mismatch <14 % Common-level variation between 50-450 MHz <25 mV tR Rise time (20-80%) 150 350 380 ps tF Fall time (20-80%) 150 350 380 ps VOL LP Output LOW level VOH LP Output HIGH level 1.1 ZOLP Output impedance of low power parameter 140 TRLP 15-85% rise time TFLP 15-85% fall time v/dtsr -50 to 50 mV 1.3 V 25 ns 25 Slew rate (CLOAD = 20-70 pF) 30 ns mV/ns Control Interface The electrical characteristics of the control interface (RESET_BAR, TEST, GPIO0, GPIO1, GPI2, and GPI3) are shown in Table 22. Table 22. DC ELECTRICAL CHARACTERISTICS (CONTROL INTERFACE) (fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_IO = 1.8 V; DVDD_1V2 = 1.2 V, Output Load = 68.5 pF; TJ = 55C) Min Typ Max Unit VIH Input HIGH Voltage Parameter 0.7 x VDD_IO - VDD_IO + 0.5 V VIL Input LOW Voltage -0.5 - VDD_IO X 0.3 V IIN Input Leakage Current - - 10 A CIN Input Pad Capacitance - 6 - pF Symbol Condition No pull-up resistor; VIN = VDD_IO or DGND Operating Voltages VAA and VAA_PIX must be at the same potential for correct operation of the AR0833. Table 23. MAXIMUM VALUE RANGES (fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_IO = 1.8V; DVDD_1V2 = 1.2 V; Output Load = 68.5 pF; TJ = 70C; Mode = Full Resolution (3264 x 2488); Frame rate = 30 fps) Symbol Parameter Min Typ Max Unit 2.5 2.8 3.1 V Pixel Supply Voltage 2.5 2.8 3.1 V Digital Voltage 1.14 1.2 1.3 V DVDD_1V8 PHY Digital Voltage 1.7 1.8 1.9 V VDD_IO I/O Digital Voltage 1.7 1.8 1.9 V 2.5 2.8 3.1 V DVDD_1V2_PHY MIPI Supply 1.14 1.2 1.3 V VAA Analog Voltage VAA_PIX DVDD_1V2 Condition www.onsemi.com 39 AR0833 Table 23. MAXIMUM VALUE RANGES(continued) (fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_IO = 1.8V; DVDD_1V2 = 1.2 V; Output Load = 68.5 pF; TJ = 70C; Mode = Full Resolution (3264 x 2488); Frame rate = 30 fps) Symbol Parameter Min Typ Max Unit H/W Standby Current Consumption - - 30 A H/W Standby Power Consumption - - 84 W Output Driving Strength 10 - - mA Slew Rate - 0.7 - V/sec Programming voltage for OTPM (VPP) 6 6.5 7 V -30 - 70 C -40 - 85 C TOP Operating Temperature TSTG Storage Temperature Condition Measure at junction Typical Operating Current Consumption (MIPI) Table 24. TYPICAL OPERATING CURRENT CONSUMPTION (MIPI) (Nominal Voltages: fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; DVDD_1V8 = 1.8 V; VDD_IO = 1.8 V; DVDD_1V2 = 1.2 V High Voltages: fEXTCLK = 24 MHz; VAA = 3.1 V; VAA_PIX = 3.1 V; DVDD_1V8 = 1.9 V; VDD_IO = 1.9 V; DVDD_1V2 = 1.3 V; TJ = 25C) Symbol Parameter IAA Analog Supply Current IAA_PIX IDD_1V8 IDD_IO IDD_1V2 Pixel Supply Current OTPM Read Supply Current I/O Supply Current Digital Supply Current Condition Min Typ Max Unit Full resolution 4:3 - 30 fps - 55 75 mA Full resolution 16:9 - 30 fps - 55 75 mA 1080p, 30 fps - 43 75 mA 720p, 60 fps - 55 75 mA VGA, 60 fps - 55 75 mA Full resolution 4:3 - 30 fps - 14 18 mA Full resolution 16:9 - 30 fps - 14 18 mA 1080p, 30 fps - 8 18 mA 720p, 60 fps - 14 18 mA VGA, 60 fps - 14 18 mA Full resolution 4:3 - 30 fps - 5 10 mA Full resolution 16:9 - 30 fps - 5 10 mA 1080p, 30 fps - 6 10 mA 720p, 60 fps - 5 10 mA VGA, 60 fps - 5 10 mA Full resolution 4:3 - 30 fps - 0.02 0.03 mA Full resolution 16:9 - 30 fps - 0.02 0.03 mA 1080p, 30 fps - 0.03 0.03 mA 720p, 60 fps - 0.02 0.03 mA VGA, 60 fps - 0.02 0.03 mA Full resolution 4:3 - 30 fps - 105 130 mA Full resolution 16:9 - 30 fps - 93 115 mA 1080p, 30 fps - 53 110 mA 720p, 60 fps - 75 90 mA VGA, 60 fps - 75 90 mA www.onsemi.com 40 AR0833 Table 24. TYPICAL OPERATING CURRENT CONSUMPTION (MIPI) (continued) (Nominal Voltages: fEXTCLK = 24 MHz; VAA = 2.8 V; VAA_PIX = 2.8 V; DVDD_1V8 = 1.8 V; VDD_IO = 1.8 V; DVDD_1V2 = 1.2 V High Voltages: fEXTCLK = 24 MHz; VAA = 3.1 V; VAA_PIX = 3.1 V; DVDD_1V8 = 1.9 V; VDD_IO = 1.9 V; DVDD_1V2 = 1.3 V; TJ = 25C) Symbol PHY supply current Parameter Condition PHY Supply Current Min Typ Max Unit Full resolution 4:3 - 30 fps - 10 14 mA Full resolution 16:9 - 30 fps - 8 11 mA 1080p, 30 fps - 1 4 mA 720p, 60 fps - 3 3 mA VGA, 60 fps - 1 2 mA Absolute Maximum Ratings Table 25. ABSOLUTE MAX VOLTAGES Symbol Parameter Min Typ Max VDD_1V2 Digital/Analog Voltage -0.3 1.5 V DVDD_1V8 OTPM -0.3 2.1 V VDD_IO I/O Digital Voltage -0.3 3.5 V Condition VAA Analog Voltage -0.3 3.5 V VAA_PIX Pixel Supply Voltage -0.3 3.5 V DVDD_1V2_PHY MIPI Supply -0.3 1.5 V Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. * MIPI Alliance Standard for CSI-2 version 1.0 * MIPI Alliance Standard for D-PHY version 1.0 MIPI SPECIFICATION REFERENCE The sensor design and this documentation is based on the following MIPI Specifications: A-PixHS is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 41 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS CLCC48 10x10 CASE 848AJ ISSUE O DATE 30 DEC 2014 DOCUMENT NUMBER: STATUS: 98AON93121F ON SEMICONDUCTOR STANDARD REFERENCE: (c) Semiconductor Components Industries, LLC, 2002 October, DESCRIPTION: 2002 - Rev. 0 CLCC48 10X10 http://onsemi.com 1 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. Case Outline Number: PAGE 1 OFXXX 2 DOCUMENT NUMBER: 98AON93121F PAGE 2 OF 2 ISSUE REVISION DATE O RELEASED FOR PRODUCTION FROM APTINA POD# AR0833 TO ON SEMICONDUCTOR. REQ. BY D. TRUHITTE. 30 DEC 2014 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. (c) Semiconductor Components Industries, LLC, 2014 December, 2014 - Rev. O Case Outline Number: 848AJ ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative