ADXL343BCCZ-RL7 - Analog Devices

3-Axis, ±2 g/±4 g/±8 g/±16 g

Digital MEMS Accelerometer

Data Sheet

ADXL343

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700 www.analog.com

FEATURES

Multipurpose accelerometer with 10- to 13-bit resolution for

use in a wide variety of applications

Digital output accessible via SPI (3- and 4-wire) and I2C

Built-in motion detection features make tap, double-tap,

activity, inactivity, and free-fall detection trivial

User-adjustable thresholds

Interrupts independently mappable to two interrupt pins

Low power operation down to 23 µA and embedded FIFO for

reducing overall system power

Wide supply voltage range: 2.0 V to 3.6 V

I/O voltage 1.7 V to VS

Wide operating temperature range (−40°C to +85°C)

10,000 g shock survival

Small, thin, Pb free, RoHS compliant 3 mm × 5 mm × 1 mm

LGA package

APPLICATIONS

Handsets

Gaming and pointing devices

Hard disk drive (HDD) protection

GENERAL DESCRIPTION

The ADXL343 is a versatile 3-axis, digital-output, low g MEMS

accelerometer. Selectable measurement range and bandwidth, and

configurable, built-in motion detection make it suitable for sensing

acceleration in a wide variety of applications. Robustness to

10,000 g of shock and a wide temperature range (−40°C to +85°C)

enable use of the accelerometer even in harsh environments.

The ADXL343 measures acceleration with high resolution (13-bit)

measurement at up to ±16 g. Digital output data is formatted as

16-bit twos complement and is accessible through either an SPI

(3- or 4-wire) or I2C digital interface. The ADXL343 can

measure the static acceleration of gravity in tilt-sensing appli-

cations, as well as dynamic acceleration resulting from motion

or shock. Its high resolution (3.9 mg/LSB) enables measurement

of inclination changes less than 1.0°.

Several special sensing functions are provided. Activity and

inactivity sensing detect the presence or lack of motion. Tap

sensing detects single and double taps in any direction. Free-fall

sensing detects if the device is falling. These functions can be

mapped individually to either of two interrupt output pins.

An integrated memory management system with a 32-level first in,

first out (FIFO) buffer can be used to store data to minimize host

processor activity and lower overall system power consumption.

The ADXL343 is supplied in a small, thin, 3 mm × 5 mm × 1 mm,

14-terminal, plastic package.

FUNCTIONAL BLOCK DIAGRAM

3-AXIS

SENSOR

SENSE

ELECTRONICS DIGITAL

FILTER

ADXL343

POWER

MANAGEMENT

CONTROL

AND

INTERRUPT

LOGIC

SERIAL I/O

INT1

VSVDD I/O

INT2

SDA/SDI/SDIO

SDO/ALT

ADDRESS

SCL/SCLK

GND

ADC

32 LEVEL

FIFO

10627-001

Figure 1.

ADXL343 Data Sheet

Rev. 0 | Page 2 of 36

TABLE OF CONTENTS

Features .............................................................................................. 1

Applications ....................................................................................... 1

General Description ......................................................................... 1

Functional Block Diagram .............................................................. 1

Revision History ............................................................................... 2

Specifications ..................................................................................... 3

Absolute Maximum Ratings ............................................................ 5

Thermal Resistance ...................................................................... 5

Package Information .................................................................... 5

ESD Caution .................................................................................. 5

Pin Configuration and Function Descriptions ............................. 6

Typical Performance Characteristics ............................................. 7

Theory of Operation ...................................................................... 11

Power Sequencing ...................................................................... 11

Power Savings.............................................................................. 12

Serial Communications ................................................................. 13

SPI ................................................................................................. 13

I2C ................................................................................................. 16

Interrupts ..................................................................................... 18

FIFO ............................................................................................. 19

Self-Test ....................................................................................... 20

Applications Information .............................................................. 26

Power Supply Decoupling ......................................................... 26

Mechanical Considerations for Mounting .............................. 26

Tap Detection .............................................................................. 26

Threshold .................................................................................... 27

Link Mode ................................................................................... 27

Sleep Mode vs. Low Power Mode............................................. 28

Offset Calibration ....................................................................... 28

Using Self-Test ............................................................................ 29

Data Formatting of Upper Data Rates ..................................... 30

Noise Performance ..................................................................... 31

Operation at Voltages Other Than 2.5 V ................................ 31

Offset Performance at Lowest Data Rates ............................... 32

Axes of Acceleration Sensitivity ............................................... 33

Layout and Design Recommendations ................................... 34

Outline Dimensions ....................................................................... 35

Ordering Guide .......................................................................... 35

REVISION HISTORY

4/12—Revision 0: Initial Version

Data Sheet ADXL343

Rev. 0 | Page 3 of 36

SPECIFICATIONS

TA = 25°C, VS = 2.5 V, V DD I/O = 1.8 V, acceleration = 0 g, CS = 10 µF tantalum, CI/O = 0.1 µF, output data rate (ODR) = 800 Hz, unless

otherwise noted. All minimum and maximum specifications are guaranteed. Typical specifications are not guaranteed.

Table 1.

Parameter Test Conditions/Comments Min Typ 1 Max Unit

SENSOR INPUT Each axis

Measurement Range User selectable ±2, ±4, ±8, ±16 g

Nonlinearity Percentage of full scale ±0.5 %

Inter-Axis Alignment Error ±0.1 Degrees

Cross-Axis Sensitivity2 ±1 %

OUTPUT RESOLUTION Each axis

All g Ranges 10-bit resolution 10 Bits

±2 g Range Full resolution 10 Bits

±4

Range

Full resolution

Bits

±8 g Range Full resolution 12 Bits

±16 g Range Full resolution 13 Bits

SENSITIVITY Each axis

Sensitivity at XOUT, YOUT, ZOUT All g ranges, full resolution 256 LSB/g

±2 g, 10-bit resolution 256 LSB/g

±4 g, 10-bit resolution 128 LSB/g

±8 g, 10-bit resolution 64 LSB/g

±16 g, 10-bit resolution 32 LSB/g

Sensitivity Deviation from Ideal

All g ranges

±1.0

Scale Factor at XOUT, YOUT, ZOUT All g ranges, full resolution 3.9 mg/LSB

±2 g, 10-bit resolution 3.9 mg/LSB

±4 g, 10-bit resolution 7.8 mg/LSB

±8 g, 10-bit resolution 15.6 mg/LSB

±16 g, 10-bit resolution

31.2

mg/LSB

Sensitivity Change Due to Temperature

±0.01

%/°C

0 g OFFSET Each axis

0 g Output Deviation from Ideal, X-, Y-, Z-Axes ±35 mg

0 g Offset vs. Temperature for X-, Y-, Z-Axes ±0.8 mg/°C

NOISE

X-, Y-, Z-Axes ODR = 100 Hz for ±2 g, 10-bit resolution

or all g-ranges, full resolution

1.1 LSB rms

OUTPUT DATA RATE AND BANDWIDTH User selectable

Output Data Rate (ODR)3, 4, 5 0.1 3200 Hz

SELF-TEST6

Output Change in X-Axis 0.20 2.10 g

Output Change in Y-Axis −2.10 −0.20 g

Output Change in Z-Axis

0.30

3.40

POWER SUPPLY

Operating Voltage Range (VS) 2.0 2.5 3.6 V

Interface Voltage Range (V

DD I/O

)

1.7

1.8

Supply Current ODR ≥ 100 Hz 140 µA

ODR < 10 Hz 30 µA

Standby Mode Leakage Current 0.1 µA

Turn-On and Wake-Up Time7 ODR = 3200 Hz 1.4 ms

ADXL343 Data Sheet

Rev. 0 | Page 4 of 36

Parameter Test Conditions/Comments Min Typ 1 Max Unit

TEMPERATURE

Operating Temperature Range −40 +85 °C

WEIGHT

Device Weight 30 mg

1 The typical specifications shown are for at least 68% of the population of parts and are based on the worst case of mean ±1 σ, except for 0 g output and sensitivity,

which represents the target value. For 0 g offset and sensitivity, the deviation from the ideal describes the worst case of mean ±1 σ.

2 Cross-axis sensitivity is defined as coupling between any two axes.

3 Bandwidth is the −3 dB frequency and is half the output data rate, bandwidth = ODR/2.

4 The output format for the 3200 Hz and 1600 Hz ODRs is different than the output format for the remaining ODRs. This difference is described in the Data Formatting of

Upper Data Rates section.

5 Output data rates below 6.25 Hz exhibit additional offset shift with increased temperature, depending on selected output data rate. Refer to the Offset Performance at

Lowest Data Rates section for details.

6 Self-test change is defined as the output (g) when the SELF_TEST bit = 1 (in the DATA_FORMAT register, Address 0x31) minus the output (g) when the SELF_TEST bit =

0. Due to device filtering, the output reaches its final value after 4 × τ when enabling or disabling self-test, where τ = 1/(data rate). The part must be in normal power

operation (LOW_POWER bit = 0 in the BW_RATE register, Address 0x2C) for self-test to operate correctly.

7 Turn-on and wake-up times are determined by the user-defined bandwidth. At a 100 Hz data rate, the turn-on and wake-up times are each approximately 11.1 ms. For

other data rates, the turn-on and wake-up times are each approximately τ + 1.1 in milliseconds, where τ = 1/(data rate).

Data Sheet ADXL343

Rev. 0 | Page 5 of 36

ABSOLUTE MAXIMUM RATINGS

Table 2.

Parameter Rating

Acceleration

Any Axis, Unpowered

10,000

Any Axis, Powered 10,000 g

VS −0.3 V to +3.9 V

VDD I/O −0.3 V to +3.9 V

Digital Pins −0.3 V to VDD I/O + 0.3 V or 3.9 V,

whichever is less

All Other Pins

−0.3 V to +3.9 V

Output Short-Circuit Duration

(Any Pin to Ground)

Indefinite

Temperature Range

Powered −40°C to +105°C

Storage −40°C to +105°C

Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress

rating only; functional operation of the device at these or any

other conditions above those indicated in the operational

section of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect

device reliability.

THERMAL RESISTANCE

Table 3. Package Characteristics

Package Type θJA θJC Device Weight

14-Terminal LGA 150°C/W 85°C/W 30 mg

PACKAGE INFORMATION

The information in Figure 2 and Table 4 provide details about

the package branding for the ADXL343. For a complete listing

of product availability, see the Ordering Guide section.

3 4 3 B

# y w w

v v v v

C N T Y

10627-102

Figure 2. Product Information on Package (Top View)

Table 4. Package Branding Information

Branding Key Field Description

343B

Part identifier for the ADXL343

# RoHS-compliant designation

yww Date code

vvvv Factory lot code

CNTY Country of origin

ESD CAUTION

ADXL343 Data Sheet

Rev. 0 | Page 6 of 36

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

SDA/SDI/SDIO

SDO /ALT ADDRES S

RESERVED

INT2

INT1

VDD I/O

GND

RESERVED

GND

4+x

+y +z

SCL/SCLK

ADXL343

TOP VI EW

(No t t o Scal e)

10627-002

NOTES

1. NC = NO I NTERNAL CO NNE CTI ON.

Figure 3. Pin Configuration (Top View)

Table 5. Pin Function Descriptions

Pin No. Mnemonic Description

1 VDD I/O Digital Interface Supply Voltage.

2 GND This pin must be connected to ground.

3 RESERVED Reserved. This pin must be connected to VS or left open.

4 GND This pin must be connected to ground.

5 GND This pin must be connected to ground.

Supply Voltage.

Chip Select.

8 INT1 Interrupt 1 Output.

9 INT2 Interrupt 2 Output.

10 NC Not Internally Connected.

11 RESERVED Reserved. This pin must be connected to ground or left open.

12 SDO/ALT ADDRESS Serial Data Output (SPI 4-Wire)/Alternate I2C Address Select (I2C).

SDA/SDI/SDIO

Serial Data (I

C)/Serial Data Input (SPI 4-Wire)/Serial Data Input and Output (SPI 3-Wire).

14 SCL/SCLK Serial Communications Clock. SCL is the clock for I2C, and SCLK is the clock for SPI.

Data Sheet ADXL343

Rev. 0 | Page 7 of 36

TYPICAL PERFORMANCE CHARACTERISTICS

–150 –100 –50 050 100 150

ZERO g OFFSET (mg)

PERCENT OF PO PULATION (%)

10627-206

Figure 4. Zero g Offset at 25°C, VS = 2.5 V, All Axes

–150 –100 –50 050 100 150

ZERO g OFFSET (mg)

PERCENT OF PO PULATION (%)

10627-209

Figure 5. Zero g Offset at 25°C, VS = 3.3 V, All Axes

–2.0 –1.5 –1.0 –0.5 00.5 1.0 1.5 2.0

ZERO g OFFSET T EMPERATURE COEFFICIENT (mg/°C)

PERCENT OF PO PULATION (%)

10627-210

Figure 6. Zero g Offset Temperature Coefficient, VS = 2.5 V, All Axes

–150

–100

–50

100

150

–40 –20 020 40 60 80 100

TEMPERAT URE ( °C)

OUTPUT (mg)

N = 16

AVDD = DV DD = 2.5V

10627-213

Figure 7. X-Axis Zero g Offset vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V

–150

–100

–50

100

150

–40 –20 020 40 60 80 100

TEMPERAT URE ( °C)

OUTPUT (mg)

N = 16

AVDD = DV DD = 2.5V

10627-214

Figure 8. Y-Axis Zero g Offset vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V

–150

–100

–50

100

150

–40 –20 020 40 60 80 100

TEMPERAT URE ( °C)

OUTPUT (mg)

N = 16

AVDD = DV DD = 2.5V

10627-215

Figure 9. Z-Axis Zero g Offset vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V

ADXL343 Data Sheet

Rev. 0 | Page 8 of 36

230 234 238 242 246 250 254 258 262 266 270 274 278 282

SENSITIVITY (LSB/g)

PERCENT OF PO PULATION (%)

10627-218

Figure 10. Sensitivity at 25°C, VS = 2.5 V, Full Resolution, All Axes

–0.02 –0.01 00.01 0.02

SENSITIVITY TEMPERATURE COEFFICIENT (%/°C)

PERCENT OF PO PULATION (%)

10627-219

Figure 11. Sensitivity Temperature Coefficient, VS = 2.5 V, All Axes

100 110 120 130 140 150 160 170 180 190 200

CURRENT CONSUMP TI ON (µ A)

PERCENT OF PO PULATION (%)

10627-231

Figure 12. Current Consumption at 25°C, 100 Hz Output Data Rate, VS = 2.5 V

020 40 60 80 100 120

TEMPERAT URE ( °C)

230

235

240

245

250

255

260

265

270

275

280

SENSITIVITY (LSB/g)

–40 –20

10627-222

Figure 13. X-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V, Full Resolution

230

235

240

245

250

255

260

265

270

275

280

TEMPERAT URE ( °C)

SENSITIVITY (LSB/g)

020 40 60 80 100 120

–40 –20

10627-223

Figure 14. Y-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V, Full Resolution

230

235

240

245

250

255

260

265

270

275

280

TEMPERAT URE ( °C)

SENSITIVITY (LSB/g)

020 40 60 80 100 120

–40 –20

10627-224

Figure 15. Z-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 2.5 V, Full Resolution

Data Sheet ADXL343

Rev. 0 | Page 9 of 36

TEMPERAT URE ( °C)

230

235

240

245

250

255

260

265

270

275

280

SENSITIVITY (LSB/g)

020 40 60 80 100 120

–40 –20

10627-225

Figure 16. X-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 3.3 V, Full Resolution

020 40 60 80 100 120

TEMPERAT URE ( °C)

230

235

240

245

250

255

260

265

270

275

280

SENSITIVITY (LSB/g)

–40 –20

10627-226

Figure 17. Y-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 3.3 V, Full Resolution

020 40 60 80 100 120

TEMPERAT URE ( °C)

230

235

240

245

250

255

260

265

270

275

280

SENSITIVITY (LSB/g)

–40 –20

10627-227

Figure 18. Z-Axis Sensitivity vs. Temperature—

Eight Parts Soldered to PCB, VS = 3.3 V, Full Resolution

0.2 0.5 0.8 1.1 1.4 1.7 2.0

SELF-T EST RESPONSE (g)

PERCENT OF PO PULATION (%)

10627-228

Figure 19. X-Axis Self-Test Response at 25°C, VS = 2.5 V

–0.2 –0.5 –0.8 –1.1 –1.4 –1.7 –2.0

SELF-T EST RESPONSE (g)

PERCENT OF PO PULATION (%)

10627-229

Figure 20. Y-Axis Self-Test Response at 25°C, VS = 2.5 V

0.3 0.9 1.5 2.1 2.7 3.3

SELF-T EST RESPONSE (g)

PERCENT OF PO PULATION (%)

10627-230

Figure 21. Z-Axis Self-Test Response at 25°C, VS = 2.5 V

ADXL343 Data Sheet

Rev. 0 | Page 10 of 36

100

120

140

160

1.60 3.12 6.25 12.50 25 50 100 200 400 800 1600 3200

OUTPUT DATA RATE (Hz)

CURRENT CONSUMP TI ON (µ A)

10627-232

Figure 22. Current Consumption vs. Output Data Rate at 25°C—10 Parts,

VS = 2.5 V

100

150

200

2.0 2.4 2.8 3.2 3.6

SUPPLY VOLTAGE (V)

SUPPLY CURRENT (µA)

10627-233

Figure 23. Supply Current vs. Supply Voltage, VS at 25°C

Data Sheet ADXL343

Rev. 0 | Page 11 of 36

THEORY OF OPERATION

The ADXL343 is a complete 3-axis acceleration measurement

system with a selectable measurement range of ±2 g, ±4 g, ±8 g,

or ±16 g. It measures both dynamic acceleration resulting from

motion or shock and static acceleration, such as gravity, that

allows the device to be used as a tilt sensor.

The sensor is a polysilicon surface-micromachined structure

built on top of a silicon wafer. Polysilicon springs suspend the

structure over the surface of the wafer and provide a resistance

against forces due to applied acceleration.

Deflection of the structure is measured using differential capacitors

that consist of independent fixed plates and plates attached to the

moving mass. Acceleration deflects the proof mass and unbalances

the differential capacitor, resulting in a sensor output whose ampli-

tude is proportional to acceleration. Phase-sensitive demodulation

is used to determine the magnitude and polarity of the acceleration.

POWER SEQUENCING

Power can be applied to VS or VDD I/O in any sequence without

damaging the ADXL343. All possible power-on modes are

summarized in Table 6. The interface voltage level is set with

the interface supply voltage, VDD I/O, which must be present to

ensure that the ADXL343 does not create a conflict on the

communication bus. For single-supply operation, VDD I/O can be

the same as the main supply, VS. In a dual-supply application,

however, VDD I/O can differ from VS to accommodate the desired

interface voltage, as long as VS is greater than or equal to VDD I/O.

After VS is applied, the device enters standby mode, where power

consumption is minimized and the device waits for VDD I/O to be

applied and for the command to enter measurement mode to be

received. (This command can be initiated by setting the measure

bit (Bit D3) in the POWER_CTL register (Address 0x2D).) In

addition, while the device is in standby mode, any register can be

written to or read from to configure the part. It is recommended

to configure the device in standby mode and then to enable

measurement mode. Clearing the measure bit returns the

device to the standby mode.

Table 6. Power Sequencing

Condition VS VDD I/O Description

Power Off Off Off The device is completely off, but there is a potential for a communication bus conflict.

Bus Disabled On Off The device is on in standby mode, but communication is unavailable and creates a conflict on

the communication bus. The duration of this state should be minimized during power-up to

prevent a conflict.

Bus Enabled Off On No functions are available, but the device does not create a conflict on the communication bus.

Standby or Measurement On On At power-up, the device is in standby mode, awaiting a command to enter measurement

mode, and all sensor functions are off. After the device is instructed to enter measurement

mode, all sensor functions are available.

ADXL343 Data Sheet

Rev. 0 | Page 12 of 36

POWER SAVINGS

Power Modes

The ADXL343 automatically modulates its power consumption

in proportion to its output data rate, as outlined in Table 7. If

additional power savings is desired, a lower power mode is

available. In this mode, the internal sampling rate is reduced,

allowing for power savings in the 12.5 Hz to 400 Hz data rate

range at the expense of slightly greater noise. To enter low power

mode, set the LOW_POWER bit (Bit 4) in the BW_RATE register

(Address 0x2C). The current consumption in low power mode

is shown in Table 8 for cases where there is an advantage to

using low power mode. Use of low power mode for a data rate

not shown in Table 8 does not provide any advantage over the same

data rate in normal power mode. Therefore, it is recommended

that only data rates shown in Table 8 are used in low power mode.

The current consumption values shown in Table 7 and Table 8

are for a VS of 2.5 V.

Table 7. Typical Current Consumption vs. Data Rate

(TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Output Data

Rate (Hz) Bandwidth (Hz) Rate Code IDD (µA)

3200 1600 1111 140

1600

800

1110

800 400 1101 140

400 200 1100 140

200 100 1011 140

100 50 1010 140

50 25 1001 90

25 12.5 1000 60

12.5 6.25 0111 50

6.25 3.13 0110 45

3.13 1.56 0101 40

1.56 0.78 0100 34

0.78 0.39 0011 23

0.39 0.20 0010 23

0.20 0.10 0001 23

0.10 0.05 0000 23

Table 8. Typical Current Consumption vs. Data Rate,

Low Power Mode (TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Output Data

Rate (Hz) Bandwidth (Hz) Rate Code IDD (µA)

400

200

1100

200 100 1011 60

100 50 1010 50

50 25 1001 45

25 12.5 1000 40

12.5 6.25 0111 34

Auto Sleep Mode

Additional power can be saved if theADXL343 automatically

switches to sleep mode during periods of inactivity. To enable

this feature, set the THRESH_INACT register (Address 0x25)

and the TIME_INACT register (Address 0x26) each to a value

that signifies inactivity (the appropriate value depends on the

application), and then set the AUTO_SLEEP bit (Bit D4) and the

link bit (Bit D5) in the POWER_CTL register (Address 0x2D).

Current consumption at the sub-12.5 Hz data rates that are

used in this mode is typically 23 µA for a VS of 2.5 V.

Standby Mode

For even lower power operation, standby mode can be used. In

standby mode, current consumption is reduced to 0.1 µA (typical).

In this mode, no measurements are made. Standby mode is

entered by clearing the measure bit (Bit D3) in the POWER_CTL

preserves the contents of FIFO.

Data Sheet ADXL343

Rev. 0 | Page 13 of 36

SERIAL COMMUNICATIONS

I2C and SPI digital communications are available. In both cases,

the ADXL343 operates as a slave. I2C mode is enabled if the CS

pin is tied high to VDD I/O. The CS pin should always be tied high

to VDD I/O or be driven by an external controller because there is

no default mode if the CS pin is left unconnected. Therefore, not

taking these precautions may result in an inability to communicate

with the part. In SPI mode, the CS pin is controlled by the bus

master. In both SPI and I2C modes of operation, data transmitted

from the ADXL343 to the master device should be ignored

during writes to the ADXL343.

SPI

For SPI, either 3- or 4-wire configuration is possible, as shown in

the connection diagrams in Figure 24 and Figure 25. Clearing the

SPI bit (Bit D6) in the DATA_FORMAT register (Address 0x31)

selects 4-wire mode, whereas setting the SPI bit selects 3-wire

mode. The maximum SPI clock speed is 5 MHz with 100 pF

maximum loading, and the timing scheme follows clock polarity

(CPOL) = 1 and clock phase (CPHA) = 1. If power is applied to

the ADXL343 before the clock polarity and phase of the host

processor are configured, the CS pin should be brought high

before changing the clock polarity and phase. When using 3-wire

SPI, it is recommended that the SDO pin be either pulled up to

VDD I/O or pulled down to GND via a 10 kΩ resistor.

PROCESSOR

MOSI

MISO

SCLK

ADXL343

SDIO

SDO

SCLK

10627-004

Figure 24. 3-Wire SPI Connection Diagram

PROCESSOR

MOSI

MISO

SCLK

ADXL343

SDI

SDO

SCLK

10627-003

Figure 25. 4-Wire SPI Connection Diagram

CS is the serial port enable line and is controlled by the SPI

master. This line must go low at the start of a transmission and

high at the end of a transmission, as shown in Figure 27. SCLK

is the serial port clock and is supplied by the SPI master. SCLK

should idle high during a period of no transmission. SDI and

SDO are the serial data input and output, respectively. Data is

updated on the falling edge of SCLK and should be sampled on

the rising edge of SCLK.

To read or write multiple bytes in a single transmission, the

multiple-byte bit, located after the R/W bit in the first byte transfer

(MB in Figure 27 to Figure 29), must be set. After the register

addressing and the first byte of data, each subsequent set of

clock pulses (eight clock pulses) causes the ADXL343 to point

to the next register for a read or write. This shifting continues

until the clock pulses cease and CS is deasserted. To perform reads or

writes on different, nonsequential registers, CS must be deasserted

between transmissions and the new register must be addressed

separately.

The timing diagram for 3-wire SPI reads or writes is shown

in Figure 29. The 4-wire equivalents for SPI writes and reads

are shown in Figure 27 and Figure 28, respectively. For correct

operation of the part, the logic thresholds and timing parameters

in Table 9 and Table 10 must be met at all times.

Use of the 3200 Hz and 1600 Hz output data rates is only

recommended with SPI communication rates greater than or

equal to 2 MHz. The 800 Hz output data rate is recommended

only for communication speeds greater than or equal to 400 kHz,

and the remaining data rates scale proportionally. For example,

the minimum recommended communication speed for a 200 Hz

output data rate is 100 kHz. Operation at an output data rate

above the recommended maximum may result in undesirable

effects on the acceleration data, including missing samples or

additional noise.

Preventing Bus Traffic Errors

The ADXL343 CS pin is used both for initiating SPI transac-

tions and for enabling I2C mode. When the ADXL343 is used on

a SPI bus with multiple devices, its CS pin is held high while the

master communicates with the other devices. There may be

conditions where a SPI command transmitted to another device

looks like a valid I2C command. In this case, the ADXL343

interprets this as an attempt to communicate in I2C mode, and

may interfere with other bus traffic. Unless bus traffic can be

adequately controlled to assure such a condition never occurs,

it is recommended to add a logic gate in front of the SDI pin

as shown in Figure 26. This OR gate holds the SDA line high

when CS is high to prevent SPI bus traffic at the ADXL343

from appearing as an I2C start command. Note that this

recommendation applies only in cases where the ADXL343

is used on a SPI bus with multiple devices.

PROCESSOR

MOSI

MISO

SCLK

ADXL343

SDIO

SDO

SCLK

10627-104

Figure 26. Recommended SPI Connection Diagram when Using Multiple SPI

Devices on a Single Bus

ADXL343 Data Sheet

Rev. 0 | Page 14 of 36

DELAY

SETUP

HOLD

SDO

X X X

WMB A5 A0 D7 D0

X X X

ADDRESS BITS DATA BITS

SCLK

QUIET

DIS

CS,DIS

SCLK

SDI

SDO

10627-017

Figure 27. SPI 4-Wire Write

X X X

R MB A5 A0

D7 D0

ADDRESS BITS

DATA BITS

DIS

SCLK

SDI

SDO

QUIET

CS,DIS

SDO

SETUP

HOLD

DELAY

SCLK

10627-018

Figure 28. SPI 4-Wire Read

tDELAY

tSETUP tHOLD tSDO

R/W MB A5 A0 D7 D0

ADDRESS BITS DATA BITS

tSCLK tMtStQUIET tCS,DIS

SCLK

SDIO

SDO

NOTES

tSDO

IS ONLY P RE S E NT DURI NG READS .

10627-019

Figure 29. SPI 3-Wire Read/Write

Data Sheet ADXL343

Rev. 0 | Page 15 of 36

Table 9. SPI Digital Input/Output

Limit1

Parameter Test Conditions Min Max Unit

Digital Input

Low Level Input Voltage (VIL) 0.3 × VDD I/O V

High Level Input Voltage (VIH) 0.7 × VDD I/O V

Low Level Input Current (IIL) VIN = VDD I/O 0.1 µA

High Level Input Current (IIH) VIN = 0 V −0.1 µA

Digital Output

Low Level Output Voltage (VOL) IOL = 10 mA 0.2 × VDD I/O V

High Level Output Voltage (VOH) IOH = −4 mA 0.8 × VDD I/O V

Low Level Output Current (IOL) VOL = VOL, max 10 mA

High Level Output Current (IOH) VOH = VOH, min −4 mA

Pin Capacitance fIN = 1 MHz, VIN = 2.5 V 8 pF

1 Limits based on characterization results, not production tested.

Table 10. SPI Timing (TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)1

Limit2, 3

Parameter

Min

Max

Unit

Description

fSCLK 5 MHz SPI clock frequency

tSCLK 200 ns 1/(SPI clock frequency) mark-space ratio for the SCLK input is 40/60 to 60/40

tDELAY 5 ns CS falling edge to SCLK falling edge

tQUIET 5 ns SCLK rising edge to CS rising edge

tDIS 10 ns CS rising edge to SDO disabled

tCS,DIS 150 ns CS deassertion between SPI communications

tS 0.3 × tSCLK ns SCLK low pulse width (space)

tM 0.3 × tSCLK ns SCLK high pulse width (mark)

tSETUP 5 ns SDI valid before SCLK rising edge

HOLD

SDI valid after SCLK rising edge

tSDO 40 ns SCLK falling edge to SDO/SDIO output transition

tR4 20 ns SDO/SDIO output high to output low transition

tF4 20 ns SDO/SDIO output low to output high transition

1 The CS, SCLK, SDI, and SDO pins are not internally pulled up or down; they must be driven for proper operation.

2 Limits based on characterization results, characterized with fSCLK = 5 MHz and bus load capacitance of 100 pF; not production tested.

3 The timing values are measured corresponding to the input thresholds (VIL and VIH) given in Table 9.

4 Output rise and fall times measured with capacitive load of 150 pF.

ADXL343 Data Sheet

Rev. 0 | Page 16 of 36

I2C

With CS tied high to VDD I/O, the ADXL343 is in I2C mode,

requiring a simple 2-wire connection, as shown in Figure 30.

The ADXL343 conforms to the UM10204 I2C-Bus Specification

and User Manual, Rev. 03—19 June 2007, available from NXP

Semiconductor. It supports standard (100 kHz) and fast (400 kHz)

data transfer modes if the bus parameters given in Table 11

and Table 12 are met. Single- or multiple-byte reads/writes are

supported, as shown in Figure 31. With the ALT ADDRESS pin

high, the 7-bit I2C address for the device is 0x1D, followed by

the R/W bit. This translates to 0x3A for a write and 0x3B for a

read. An alternate I2C address of 0x53 (followed by the R/W bit)

can be chosen by grounding the ALT ADDRESS pin (Pin 12).

This translates to 0xA6 for a write and 0xA7 for a read.

There are no internal pull-up or pull-down resistors for any

unused pins; therefore, there is no known state or default state

for the CS or ALT ADDRESS pin if left floating or unconnected.

It is required that the CS pin be connected to VDD I/O and that

the ALT ADDRESS pin be connected to either VDD I/O or GND

when using I2C.

Due to communication speed limitations, the maximum output

data rate when using 400 kHz I2C is 800 Hz and scales linearly

with a change in the I2C communication speed. For example,

using I2C at 100 kHz limits the maximum ODR to 200 Hz.

Operation at an output data rate above the recommended maxi-

mum may result in undesirable effect on the acceleration data,

including missing samples or additional noise.

PROCESSOR

D IN/OUT

D OUT

VDD I/O

ADXL343

SDA

ALT ADDRESS

SCL

10627-008

Figure 30. I2C Connection Diagram (Address 0x53)

If other devices are connected to the same I2C bus, the nominal

operating voltage level of these other devices cannot exceed VDD I/O

by more than 0.3 V. External pull-up resistors, RP, are necessary for

proper I2C operation. Refer to the UM10204 I2C-Bus Specification

and User Manual, Rev. 03—19 June 2007, when selecting pull-up

resistor values to ensure proper operation.

Table 11. I2C Digital Input/Output

Limit1

Parameter Test Conditions Min Max Unit

Digital Input

Low Level Input Voltage (VIL) 0.3 × VDD I/O V

High Level Input Voltage (VIH) 0.7 × VDD I/O V

Low Level Input Current (IIL) VIN = VDD I/O 0.1 µA

High Level Input Current (IIH) VIN = 0 V −0.1 µA

Digital Output

Low Level Output Voltage (VOL) VDD I/O < 2 V, IOL = 3 mA 0.2 × VDD I/O V

VDD I/O ≥ 2 V, IOL = 3 mA 400 mV

Low Level Output Current (IOL) VOL = VOL, max 3 mA

Pin Capacitance fIN = 1 MHz, VIN = 2.5 V 8 pF

1 Limits based on characterization results; not production tested.

MASTER START SLAVE ADDRESS + WRI TE REGISTER ADDRESS

SLAVE ACK ACK ACK

MASTER START SLAVE ADDRESS + WRI TE REGISTER ADDRESS

SLAVE ACK ACK ACK ACK

MASTER START SLAVE ADDRESS + WRI TE REGISTER ADDRESS STOP

SLAVE ACK ACK

MASTER START

START

SLAVE ADDRESS + WRI T E REG ISTER ADDRESS NACK STOP

SLAVE ACK ACK DATA

STOP

ACK

SINGLE-BYTE WRI TE

MULTI PLE-BYTE WRI TE

DATA

MULTIPLE-BYTE READ

SLAVE ADDRESS + READ

ACK

DATA

STOP

NACK

ACK

SINGLE-BYTE READ

10627-033

1THIS START IS EITHER A RESTART OR A STOP FOLLOWED BY A START.

NOTES

1. THE SHADE D ARE AS RE P RE S E NT W HE N THE DE V ICE IS L ISTENING .

Figure 31. I2C Device Addressing

Data Sheet ADXL343

Rev. 0 | Page 17 of 36

Table 12. I2C Timing (TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Limit1, 2

Parameter Min Max Unit Description

fSCL 400 kHz SCL clock frequency

t1 2.5 µs SCL cycle time

t2 0.6 µs tHIGH, SCL high time

t3 1.3 µs tLOW, SCL low time

t4 0.6 µs tHD, STA, start/repeated start condition hold time

t5 100 ns tSU, DAT, data setup time

t63, 4, 5, 6 0 0.9 µs tHD, DAT , data hold time

t7 0.6 µs tSU, STA, setup time for repeated start

t8 0.6 µs tSU, STO, stop condition setup time

t9 1.3 µs tBUF, bus-free time between a stop condition and a start condition

t10 300 ns tR, rise time of both SCL and SDA when receiving

0 ns tR, rise time of both SCL and SDA when receiving or transmitting

300

, fall time of SDA when receiving

250

, fall time of both SCL and SDA when transmitting

Cb 400 pF Capacitive load for each bus line

1 Limits based on characterization results, with fSCL = 400 kHz and a 3 mA sink current; not production tested.

2 All values referred to the VIH and the VIL levels given in Table 11.

3 t6 is the data hold time that is measured from the falling edge of SCL. It applies to data in transmission and acknowledge.

4 A transmitting device must internally provide an output hold time of at least 300 ns for the SDA signal (with respect to VIH(min) of the SCL signal) to bridge the

undefined region of the falling edge of SCL.

5 The maximum t6 value must be met only if the device does not stretch the low period (t3) of the SCL signal.

6 The maximum value for t6 is a function of the clock low time (t3), the clock rise time (t10), and the minimum data setup time (t5(min)). This value is calculated as

t6(max) = t3 − t10 − t5(min).

SDA

SCL

t3t10 t11 t4

t4t6t2t5t7t1t8

START

CONDITION REPEATED

START

CONDITION

STOP

CONDITION

10627-034

Figure 32. I2C Timing Diagram

ADXL343 Data Sheet

Rev. 0 | Page 18 of 36

INTERRUPTS

The ADXL343 provides two output pins for driving interrupts:

INT1 and INT2. Both interrupt pins are push-pull, low impedance

pins with output specifications shown in Table 13. The default

configuration of the interrupt pins is active high. This can be

changed to active low by setting the INT_INVERT bit in the

DATA_FORMAT (Address 0x31) register. All functions can

be used simultaneously, with the only limiting feature being

that some functions may need to share interrupt pins.

Interrupts are enabled by setting the appropriate bit in the

INT_ENABLE register (Address 0x2E) and are mapped to

either the INT1 or INT2 pin based on the contents

of the INT_MAP register (Address 0x2F). When initially

configuring the interrupt pins, it is recommended that the

functions and interrupt mapping be done before enabling the

interrupts. When changing the configuration of an interrupt, it

is recommended that the interrupt be disabled first, by clearing

the bit corresponding to that function in the INT_ENABLE

the interrupt again. Configuration of the functions while the

interrupts are disabled helps to prevent the accidental generation

of an interrupt before desired.

The interrupt functions are latched and cleared by either reading the

data registers (Address 0x32 to Address 0x37) until the interrupt

condition is no longer valid for the data-related interrupts or by

reading the INT_SOURCE register (Address 0x30) for the

remaining interrupts. This section describes the interrupts

that can be set in the INT_ENABLE register and monitored

in the INT_SOURCE register.

DATA_READY

The DATA_READY bit is set when new data is available and is

cleared when no new data is available.

SINGLE_TAP

The SINGLE_TAP bit is set when a single acceleration event

that is greater than the value in the THRESH_TAP register

(Address 0x1D) occurs for less time than is specified in the

DUR register (Address 0x21).

DOUBLE_TAP

The DOUBLE_TAP bit is set when two acceleration events

that are greater than the value in the THRESH_TAP register

(Address 0x1D) occur for less time than is specified in the DUR

time specified by the latent register (Address 0x22) but within

the time specified in the window register (Address 0x23). See

the Tap Detection section for more details.

Activity

The activity bit is set when acceleration greater than the value stored

in the THRESH_ACT register (Address 0x24) is experienced on

any participating axis, set by the ACT_INACT_CTL register

(Address 0x27).

Inactivity

The inactivity bit is set when acceleration of less than the

value stored in the THRESH_INACT register (Address 0x25) is

experienced for more time than is specified in the TIME_INACT

ACT_INACT_CTL register (Address 0x27). The maximum value

for TIME_INACT is 255 sec.

FREE_FALL

The FREE_FALL bit is set when acceleration of less than the

value stored in the THRESH_FF register (Address 0x28) is

experienced for more time than is specified in the TIME_FF

interrupt differs from the inactivity interrupt as follows: all axes

always participate and are logically AND’ed, the timer period is

much smaller (1.28 sec maximum), and the mode of operation is

always dc-coupled.

Watermark

The watermark bit is set when the number of samples in FIFO

equals the value stored in the samples bits (Register FIFO_CTL,

Address 0x38). The watermark bit is cleared automatically when

FIFO is read, and the content returns to a value below the value

stored in the samples bits.

Table 13. Interrupt Pin Digital Output

Limit1

Parameter Test Conditions Min Max Unit

Digital Output

Low Level Output Voltage (V

)

= 300 µA

0.2 × V

DD I/O

High Level Output Voltage (V

)

= −150 µA

0.8 × V

DD I/O

Low Level Output Current (I

)

= V

OL, max

300

µA

High Level Output Current (I

)

= V

OH, min

−150

µA

Pin Capacitance

= 1 MHz, V

= 2.5 V

Rise/Fall Time

Rise Time (t

LOAD

= 150 pF

210

Fall Time (tF)3 CLOAD = 150 pF 150 ns

1 Limits based on characterization results, not production tested.

2 Rise time is measured as the transition time from VOL, max to VOH, min of the interrupt pin.

3 Fall time is measured as the transition time from VOH, min to VOL, max of the interrupt pin.

Data Sheet ADXL343

Rev. 0 | Page 19 of 36

Overrun

The overrun bit is set when new data replaces unread data.

The precise operation of the overrun function depends on the

FIFO mode. In bypass mode, the overrun bit is set when new data

replaces unread data in the DATAX, DATAY, and DATAZ registers

(Address 0x32 to Address 0x37). In all other modes, the overrun bit

is set when FIFO is filled. The overrun bit is automatically cleared

when the contents of FIFO are read.

FIFO

The ADXL343 contains an embedded memory management

system with a 32-level FIFO memory buffer that can be used to

minimize host processor burden. This buffer has four modes:

bypass, FIFO, stream, and trigger (see Table 22). Each mode is

selected by the settings of the FIFO_MODE bits (Bits[D7:D6])

in the FIFO_CTL register (Address 0x38).

If use of the FIFO is not desired, the FIFO should be placed in

bypass mode.

Bypass Mode

In bypass mode, FIFO is not operational and, therefore,

remains empty.

FIFO Mode

In FIFO mode, data from measurements of the x-, y-, and z-axes

are stored in FIFO. When the number of samples in FIFO equals

the level specified in the samples bits of the FIFO_CTL register

(Address 0x38), the watermark interrupt is set. FIFO continues

accumulating samples until it is full (32 samples from measurements

of the x-, y-, and z-axes) and then stops collecting data. After FIFO

stops collecting data, the device continues to operate; therefore,

features such as tap detection can be used after FIFO is full. The

watermark interrupt continues to occur until the number of

samples in FIFO is less than the value stored in the samples bits

of the FIFO_CTL register.

Stream Mode

In stream mode, data from measurements of the x-, y-, and z-

axes are stored in FIFO. When the number of samples in FIFO

equals the level specified in the samples bits of the FIFO_CTL

continues accumulating samples and holds the latest 32 samples

from measurements of the x-, y-, and z-axes, discarding older

data as new data arrives. The watermark interrupt continues

occurring until the number of samples in FIFO is less than the

value stored in the samples bits of the FIFO_CTL register.

Trigger Mode

In trigger mode, FIFO accumulates samples, holding the latest

32 samples from measurements of the x-, y-, and z-axes. After

a trigger event occurs and an interrupt is sent to the INT1 or

INT2 pin (determined by the trigger bit in the FIFO_CTL register),

FIFO keeps the last n samples (where n is the value specified by

the samples bits in the FIFO_CTL register) and then operates in

FIFO mode, collecting new samples only when FIFO is not full.

A delay of at least 5 µs should be present between the trigger event

occurring and the start of reading data from the FIFO to allow

the FIFO to discard and retain the necessary samples. Additional

trigger events cannot be recognized until the trigger mode is

reset. To reset the trigger mode, set the device to bypass mode

and then set the device back to trigger mode. Note that the FIFO

data should be read first because placing the device into bypass

mode clears FIFO.

Retrieving Data from FIFO

The FIFO data is read through the DATAX, DATAY, and DATAZ

registers (Address 0x32 to Address 0x37). When the FIFO is in

FIFO, stream, or trigger mode, reads to the DATAX, DATAY,

and DATAZ registers read data stored in the FIFO. Each time

data is read from the FIFO, the oldest x-, y-, and z-axes data are

placed into the DATAX, DATAY, and DATAZ registers.

If a single-byte read operation is performed, the remaining

bytes of data for the current FIFO sample are lost. Therefore, all

axes of interest should be read in a burst (or multiple-byte) read

operation. To ensure that the FIFO has completely popped (that

is, that new data has completely moved into the DATAX, DATAY,

and DATAZ registers), there must be at least 5 µs between the

end of reading the data registers and the start of a new read of

the FIFO or a read of the FIFO_STATUS register (Address 0x39).

The end of reading a data register is signified by the transition

from Register 0x37 to Register 0x38 or by the CS pin going high.

For SPI operation at 1.6 MHz or less, the register addressing

portion of the transmission is a sufficient delay to ensure that

the FIFO has completely popped. For SPI operation greater than

1.6 MHz, it is necessary to deassert the CS pin to ensure a total

delay of 5 µs; otherwise, the delay is not sufficient. The total delay

necessary for 5 MHz operation is at most 3.4 µs. This is not a

concern when using I2C mode because the communication rate is

low enough to ensure a sufficient delay between FIFO reads.

ADXL343 Data Sheet

Rev. 0 | Page 20 of 36

SELF-TEST

The ADXL343 incorporates a self-test feature that effectively

tests its mechanical and electronic systems simultaneously.

When the self-test function is enabled (via the SELF_TEST bit

in the DATA_FORMAT register, Address 0x31), an electrostatic

force is exerted on the mechanical sensor. This electrostatic force

moves the mechanical sensing element in the same manner as

acceleration, and it is additive to the acceleration experienced

by the device. This added electrostatic force results in an output

change in the x-, y-, and z-axes. Because the electrostatic force

is proportional to VS2, the output change varies with VS. This

effect is shown in Figure 33. The scale factors shown in Table 14

can be used to adjust the expected self-test output limits for

different supply voltages, VS. The self-test feature of the

ADXL343 also exhibits a bimodal behavior. However, the limits

shown in Table 1 and Table 15 to Table 18 are valid for both

potential self-test values due to bimodality. Use of the self-test

feature at data rates less than 100 Hz or at 1600 Hz may yield

values outside these limits. Therefore, the part must be in normal

power operation (LOW_POWER bit = 0 in BW_RATE register,

Address 0x2C) and be placed into a data rate of 100 Hz through

800 Hz or 3200 Hz for the self-test function to operate correctly.

–6

–4

–2

2.0 2.5 3.3 3.6

VS (V)

SELF-TEST SHIFT LIMIT (g)

X HIGH

X LOW

Y HIGH

Y LOW

Z HIGH

Z LOW

10627-242

Figure 33. Self-Test Output Change Limits vs. Supply Voltage

Table 14. Self-Test Output Scale Factors for Different Supply

Voltages, VS

Supply Voltage, VS (V) X-Axis, Y-Axis Z-Axis

2.00 0.64 0.8

2.50 1.00 1.00

3.30 1.77 1.47

3.60

2.11

1.69

Table 15. Self-Test Output in LSB for ±2 g, 10-Bit or Full

Resolution (TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Axis Min Max Unit

X 50 540 LSB

Y −540 −50 LSB

Z 75 875 LSB

Table 16. Self-Test Output in LSB for ±4 g, 10-Bit Resolution

(TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Axis Min Max Unit

270

LSB

Y −270 −25 LSB

Z 38 438 LSB

Table 17. Self-Test Output in LSB for ±8 g, 10-Bit Resolution

(TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Axis Min Max Unit

X 12 135 LSB

Y −135 −12 LSB

Z 19 219 LSB

Table 18. Self-Test Output in LSB for ±16 g, 10-Bit Resolution

(TA = 25°C, VS = 2.5 V, VDD I/O = 1.8 V)

Axis Min Max Unit

X 6 67 LSB

Y −67 −6 LSB

Z 10 110 LSB

Data Sheet ADXL343

Rev. 0 | Page 21 of 36

Table 19.

Address

Hex Dec Name Type Reset Value Description

0x00 0 DEVID R 11100101 Device ID

0x01 to 0x1C 1 to 28 Reserved Reserved; do not access

0x1D

THRESH_TAP

00000000

Tap threshold

0x1E 30 OFSX R/W 00000000 X-axis offset

0x1F 31 OFSY R/W 00000000 Y-axis offset

0x20 32 OFSZ R/W 00000000 Z-axis offset

0x21 33 DUR R/W 00000000 Tap duration

0x22 34 Latent R/W 00000000 Tap latency

0x23

Window

00000000

Tap window

0x24 36 THRESH_ACT R/W 00000000 Activity threshold

0x25 37 THRESH_INACT R/W 00000000 Inactivity threshold

0x26 38 TIME_INACT R/W 00000000 Inactivity time

0x27 39 ACT_INACT_CTL R/W 00000000 Axis enable control for activity and inactivity detection

0x28

THRESH_FF

00000000

Free-fall threshold

0x29 41 TIME_FF R/W 00000000 Free-fall time

0x2A 42 TAP_AXES R/W 00000000 Axis control for single tap/double tap

0x2B 43 ACT_TAP_STATUS R 00000000 Source of single tap/double tap

0x2C 44 BW_RATE R/W 00001010 Data rate and power mode control

0x2D 45 POWER_CTL R/W 00000000 Power-saving features control

0x2E

INT_ENABLE

00000000

Interrupt enable control

0x2F 47 INT_MAP R/W 00000000 Interrupt mapping control

0x30 48 INT_SOURCE R 00000010 Source of interrupts

0x31 49 DATA_FORMAT R/W 00000000 Data format control

0x32 50 DATAX0 R 00000000 X-Axis Data 0

0x33 51 DATAX1 R 00000000 X-Axis Data 1

0x34 52 DATAY0 R 00000000 Y-Axis Data 0

0x35 53 DATAY1 R 00000000 Y-Axis Data 1

0x36 54 DATAZ0 R 00000000 Z-Axis Data 0

0x37 55 DATAZ1 R 00000000 Z-Axis Data 1

0x38 56 FIFO_CTL R/W 00000000 FIFO control

0x39

FIFO_STATUS

00000000

FIFO status

ADXL343 Data Sheet

Rev. 0 | Page 22 of 36

D7 D6 D5 D4 D3 D2 D1 D0

1 1 1 0 0 1 0 1

The DEVID register holds a fixed device ID code of 0xE5 (345 octal).

The THRESH_TAP register is eight bits and holds the threshold

value for tap interrupts. The data format is unsigned, therefore,

the magnitude of the tap event is compared with the value

in THRESH_TAP for normal tap detection. The scale factor is

62.5 mg/LSB (that is, 0xFF = 16 g). A value of 0 may result in

undesirable behavior if single tap/double tap interrupts are

enabled.

OFSY, OFSZ (Read/Write)

The OFSX, OFSY, and OFSZ registers are each eight bits and

offer user-set offset adjustments in twos complement format

with a scale factor of 15.6 mg/LSB (that is, 0x7F = 2 g). The

value stored in the offset registers is automatically added to the

acceleration data, and the resulting value is stored in the output

data registers. For additional information regarding offset

calibration and the use of the offset registers, refer to the Offset

Calibration section.

The DUR register is eight bits and contains an unsigned time

value representing the maximum time that an event must be

above the THRESH_TAP threshold to qualify as a tap event. The

scale factor is 625 µs/LSB. A value of 0 disables the single tap/

double tap functions.

The latent register is eight bits and contains an unsigned time

value representing the wait time from the detection of a tap

event to the start of the time window (defined by the window

The scale factor is 1.25 ms/LSB. A value of 0 disables the double tap

function.

The window register is eight bits and contains an unsigned time

value representing the amount of time after the expiration of the

latency time (determined by the latent register) during which a

second valid tap can begin. The scale factor is 1.25 ms/LSB. A

value of 0 disables the double tap function.

The THRESH_ACT register is eight bits and holds the threshold

value for detecting activity. The data format is unsigned,

therefore, the magnitude of the activity event is compared

with the value in the THRESH_ACT register. The scale factor

is 62.5 mg/LSB. A value of 0 may result in undesirable behavior

if the activity interrupt is enabled.

The THRESH_INACT register is eight bits and holds the threshold

value for detecting inactivity. The data format is unsigned,

therefore, the magnitude of the inactivity event is compared

with the value in the THRESH_INACT register. The scale factor

is 62.5 mg/LSB. A value of 0 may result in undesirable behavior

if the inactivity interrupt is enabled.

The TIME_INACT register is eight bits and contains an unsigned

time value representing the amount of time that acceleration

must be less than the value in the THRESH_INACT register for

inactivity to be declared. The scale factor is 1 sec/LSB. Unlike

the other interrupt functions, which use unfiltered data (see the

Threshold section), the inactivity function uses filtered output

data. At least one output sample must be generated for the

inactivity interrupt to be triggered. This results in the function

appearing unresponsive if the TIME_INACT register is set to a

value less than the time constant of the output data rate. A value

of 0 results in an interrupt when the output data is less than the

value in the THRESH_INACT register.

ACT ac/dc ACT_X enable ACT_Y enable ACT_Z enable

D3 D2 D1 D0

INACT ac/dc INACT_X enable INACT_Y enable INACT_Z enable

ACT AC/DC and INACT AC/DC Bits

A setting of 0 selects dc-coupled operation, and a setting of 1

enables ac-coupled operation. In dc-coupled operation, the

current acceleration magnitude is compared directly with

THRESH_ACT and THRESH_INACT to determine whether

activity or inactivity is detected.

In ac-coupled operation for activity detection, the acceleration

value at the start of activity detection is taken as a reference

value. New samples of acceleration are then compared to this

reference value, and if the magnitude of the difference exceeds

the THRESH_ACT value, the device triggers an activity interrupt.

Similarly, in ac-coupled operation for inactivity detection, a

reference value is used for comparison and is updated whenever

the device exceeds the inactivity threshold. After the reference

value is selected, the device compares the magnitude of the

difference between the reference value and the current acceleration

with THRESH_INACT. If the difference is less than the value in

THRESH_INACT for the time in TIME_INACT, the device is

considered inactive and the inactivity interrupt is triggered.

Data Sheet ADXL343

Rev. 0 | Page 23 of 36

ACT_x Enable Bits and INACT_x Enable Bits

A setting of 1 enables x-, y-, or z-axis participation in detecting

activity or inactivity. A setting of 0 excludes the selected axis from

participation. If all axes are excluded, the function is disabled.

For activity detection, all participating axes are logically OR’ed,

causing the activity function to trigger when any of the partici-

pating axes exceeds the threshold. For inactivity detection, all

participating axes are logically AND’ed, causing the inactivity

function to trigger only if all participating axes are below the

threshold for the specified time.

The THRESH_FF register is eight bits and holds the threshold

value, in unsigned format, for free-fall detection. The acceleration on

all axes is compared with the value in THRESH_FF to determine if

a free-fall event occurred. The scale factor is 62.5 mg/LSB. Note

that a value of 0 mg may result in undesirable behavior if the free-

fall interrupt is enabled. Values between 300 mg and 600 mg

(0x05 to 0x09) are recommended.

The TIME_FF register is eight bits and stores an unsigned time

value representing the minimum time that the value of all axes

must be less than THRESH_FF to generate a free-fall interrupt.

The scale factor is 5 ms/LSB. A value of 0 may result in undesirable

behavior if the free-fall interrupt is enabled. Values between 100 ms

and 350 ms (0x14 to 0x46) are recommended.

D7 D6 D5 D4 D3 D2 D1 D0

Suppress

TAP_X

enable

TAP_Y

enable

TAP_Z

enable

Suppress Bit

Setting the suppress bit suppresses double tap detection if

acceleration greater than the value in THRESH_TAP is present

between taps. See the Tap Detection section for more details.

TAP_x Enable Bits

A setting of 1 in the TAP_X enable, TAP_Y enable, or TAP_Z

enable bit enables x-, y-, or z-axis participation in tap detection.

A setting of 0 excludes the selected axis from participation in

tap detection.

D7 D6 D5 D4 D3 D2 D1 D0

0 ACT_X

source

ACT_Y

source

ACT_Z

source

Asleep TAP_X

source

TAP_Y

source

TAP_Z

source

ACT_x Source and TAP_x Source Bits

These bits indicate the first axis involved in a tap or activity

event. A setting of 1 corresponds to involvement in the event,

and a setting of 0 corresponds to no involvement. When new

data is available, these bits are not cleared but are overwritten by

the new data. The ACT_TAP_STATUS register should be read

before clearing the interrupt. Disabling an axis from participation

clears the corresponding source bit when the next activity or

single tap/double tap event occurs.

Asleep Bit

A setting of 1 in the asleep bit indicates that the part is

asleep, and a setting of 0 indicates that the part is not asleep.

This bit toggles only if the device is configured for auto sleep.

See the AUTO_SLEEP Bit section for more information on

autosleep mode.

D7 D6 D5 D4 D3 D2 D1 D0

LOW_POWER

Rate

LOW_POWER Bit

A setting of 0 in the LOW_POWER bit selects normal operation,

and a setting of 1 selects reduced power operation, which has

somewhat higher noise (see the Power Modes section for details).

Rate Bits

These bits select the device bandwidth and output data rate (see

Table 7 and Table 8 for details). The default value is 0x0A, which

translates to a 100 Hz output data rate. An output data rate should

be selected that is appropriate for the communication protocol

and frequency selected. Selecting too high of an output data rate with

a low communication speed results in samples being discarded.

D7 D6 D5 D4 D3 D2 D1 D0

0 0 Link AUTO_SLEEP Measure Sleep Wakeup

Link Bit

A setting of 1 in the link bit with both the activity and inactivity

functions enabled delays the start of the activity function until

inactivity is detected. After activity is detected, inactivity detection

begins, preventing the detection of activity. This bit serially links

the activity and inactivity functions. When this bit is set to 0,

the inactivity and activity functions are concurrent. Additional

information can be found in the Link Mode section.

When clearing the link bit, it is recommended that the part be

placed into standby mode and then set back to measurement

mode with a subsequent write. This is done to ensure that the

device is properly biased if sleep mode is manually disabled;

otherwise, the first few samples of data after the link bit is cleared

may have additional noise, especially if the device was asleep

when the bit was cleared.

AUTO_SLEEP Bit

If the link bit is set, a setting of 1 in the AUTO_SLEEP bit enables

the auto-sleep functionality. In this mode, the ADXL343 auto-

matically switches to sleep mode if the inactivity function is

enabled and inactivity is detected (that is, when acceleration is

below the THRESH_INACT value for at least the time indicated

by TIME_INACT). If activity is also enabled, the ADXL343

automatically wakes up from sleep after detecting activity and

returns to operation at the output data rate set in the BW_RATE

switching to sleep mode. See the description of the Sleep Bit in

this section for more information on sleep mode.

ADXL343 Data Sheet

Rev. 0 | Page 24 of 36

If the link bit is not set, the AUTO_SLEEP feature is disabled

and setting the AUTO_SLEEP bit does not have an impact on

device operation. Refer to the Link Bit section or the Link Mode

section for more information on utilization of the link feature.

When clearing the AUTO_SLEEP bit, it is recommended that the

part be placed into standby mode and then set back to measure-

ment mode with a subsequent write. This is done to ensure that

the device is properly biased if sleep mode is manually disabled;

otherwise, the first few samples of data after the AUTO_SLEEP

bit is cleared may have additional noise, especially if the device

was asleep when the bit was cleared.

Measure Bit

A setting of 0 in the measure bit places the part into standby mode,

and a setting of 1 places the part into measurement mode. The

ADXL343 powers up in standby mode with minimum power

consumption.

Sleep Bit

A setting of 0 in the sleep bit puts the part into the normal mode

of operation, and a setting of 1 places the part into sleep mode.

Sleep mode suppresses DATA_READY, stops transmission of data

to FIFO, and switches the sampling rate to one specified by the

wakeup bits. In sleep mode, only the activity function can be used.

When the DATA_READY interrupt is suppressed, the output

data registers (Register 0x32 to Register 0x37) are still updated

at the sampling rate set by the wakeup bits (D1:D0).

When clearing the sleep bit, it is recommended that the part be

placed into standby mode and then set back to measurement

mode with a subsequent write. This is done to ensure that the

device is properly biased if sleep mode is manually disabled;

otherwise, the first few samples of data after the sleep bit is

cleared may have additional noise, especially if the device was

asleep when the bit was cleared.

Wakeup Bits

These bits control the frequency of readings in sleep mode as

described in Table 20.

Table 20. Frequency of Readings in Sleep Mode

Setting

D1 D0 Frequency (Hz)

0 0 8

0 1 4

1 1 1

D7 D6 D5 D4

DATA_READY SINGLE_TAP DOUBLE_TAP Activity

D3 D2 D1 D0

Inactivity FREE_FALL Watermark Overrun

Setting bits in this register to a value of 1 enables their respective

functions to generate interrupts, whereas a value of 0 prevents

the functions from generating interrupts. The DATA_READY,

watermark, and overrun bits enable only the interrupt output;

the functions are always enabled. It is recommended that interrupts

be configured before enabling their outputs.

D7 D6 D5 D4

DATA_READY SINGLE_TAP DOUBLE_TAP Activity

D3 D2 D1 D0

Inactivity FREE_FALL Watermark Overrun

Any bits set to 0 in this register send their respective interrupts to

the INT1 pin, whereas bits set to 1 send their respective interrupts

to the INT2 pin. All selected interrupts for a given pin are OR’ed.

D7 D6 D5 D4

DATA_READY SINGLE_TAP DOUBLE_TAP Activity

D3 D2 D1 D0

Inactivity FREE_FALL Watermark Overrun

Bits set to 1 in this register indicate that their respective functions

have triggered an event, whereas a value of 0 indicates that the

corresponding event has not occurred. The DATA_READY,

watermark, and overrun bits are always set if the corresponding

events occur, regardless of the INT_ENABLE register settings,

and are cleared by reading data from the DATAX, DATAY, and

DATAZ registers. The DATA_READY and watermark bits may

require multiple reads, as indicated in the FIFO mode descriptions

in the FIFO section. Other bits, and the corresponding interrupts,

are cleared by reading the INT_SOURCE register.

D7 D6 D5 D4 D3 D2 D1 D0

SELF_TEST SPI INT_INVERT 0 FULL_RES Justify Range

The DATA_FORMAT register controls the presentation of data

to Register 0x32 through Register 0x37. All data, except that for

the ±16 g range, must be clipped to avoid rollover.

SELF_TEST Bit

A setting of 1 in the SELF_TEST bit applies a self-test force to

the sensor, causing a shift in the output data. A value of 0 disables

the self-test force.

SPI Bit

A value of 1 in the SPI bit sets the device to 3-wire SPI mode,

and a value of 0 sets the device to 4-wire SPI mode.

Data Sheet ADXL343

Rev. 0 | Page 25 of 36

INT_INVERT Bit

A value of 0 in the INT_INVERT bit sets the interrupts to active

high, and a value of 1 sets the interrupts to active low.

FULL_RES Bit

When this bit is set to a value of 1, the device is in full resolution

mode, where the output resolution increases with the g range

set by the range bits to maintain a 4 mg/LSB scale factor. When

the FULL_RES bit is set to 0, the device is in 10-bit mode, and

the range bits determine the maximum g range and scale factor.

Justify Bit

A setting of 1 in the justify bit selects left-justified (MSB) mode,

and a setting of 0 selects right-justified mode with sign extension.

Range Bits

These bits set the g range as described in Table 21.

Table 21. g Range Setting

Setting

D1 D0 g Range

0 0 ±2 g

0 1 ±4 g

±8

1 1 ±16 g

DATAY0, DATAY1, DATAZ0, DATAZ1 (Read Only)

These six bytes (Register 0x32 to Register 0x37) are eight bits

each and hold the output data for each axis. Register 0x32 and

and Register 0x37 hold the output data for the z-axis. The output

data is twos complement, with DATAx0 as the least significant

byte and DATAx1 as the most significant byte, where x represent X,

Y, or Z. The DATA_FORMAT register (Address 0x31) controls

the format of the data. It is recommended that a multiple-byte

read of all registers be performed to prevent a change in data

between reads of sequential registers.

D7 D6 D5 D4 D3 D2 D1 D0

FIFO_MODE

Trigger

Samples

FIFO_MODE Bits

These bits set the FIFO mode, as described in Table 22.

Table 22. FIFO Modes

Setting

D7 D6 Mode Function

0 0 Bypass FIFO is bypassed.

0 1 FIFO FIFO collects up to 32 values and then

stops collecting data, collecting new data

only when FIFO is not full.

Stream

FIFO holds the last 32 data values. When

FIFO is full, the oldest data is overwritten

with newer data.

1 1 Trigger When triggered by the trigger bit, FIFO

holds the last data samples before the

trigger event and then continues to collect

data until full. New data is collected only

when FIFO is not full.

Trigger Bit

A value of 0 in the trigger bit links the trigger event of trigger mode

to INT1, and a value of 1 links the trigger event to INT2.

Samples Bits

The function of these bits depends on the FIFO mode selected

(see Table 23). Entering a value of 0 in the samples bits immedi-

ately sets the watermark status bit in the INT_SOURCE

operation may occur if a value of 0 is used for the samples bits

when trigger mode is used.

Table 23. Samples Bits Functions

FIFO Mode Samples Bits Function

Bypass None.

FIFO

Specifies how many FIFO entries are needed to

trigger a watermark interrupt.

Stream Specifies how many FIFO entries are needed to

trigger a watermark interrupt.

Trigger Specifies how many FIFO samples are retained in

the FIFO buffer before a trigger event.

0x39—FIFO_STATUS (Read Only)

D7 D6 D5 D4 D3 D2 D1 D0

FIFO_TRIG 0 Entries

FIFO_TRIG Bit

A 1 in the FIFO_TRIG bit corresponds to a trigger event occurring,

and a 0 means that a FIFO trigger event has not occurred.

Entries Bits

These bits report how many data values are stored in FIFO.

Access to collect the data from FIFO is provided through the

DATAX, DATAY, and DATAZ registers. FIFO reads must be

done in burst or multiple-byte mode because each FIFO level is

cleared after any read (single- or multiple-byte) of FIFO. FIFO

stores a maximum of 32 entries, which equates to a maximum

of 33 entries available at any given time because an additional

entry is available at the output filter of the device.

ADXL343 Data Sheet

Rev. 0 | Page 26 of 36

APPLICATIONS INFORMATION

POWER SUPPLY DECOUPLING

A 1 µF tantalum capacitor (CS) at VS and a 0.1 µF ceramic capacitor

(CI/O) at VDD I/O placed close to the ADXL343 supply pins is

recommended to adequately decouple the accelerometer from

noise on the power supply. If additional decoupling is necessary,

a resistor or ferrite bead, no larger than 100 Ω, in series with VS

may be helpful. Additionally, increasing the bypass capacitance

on VS to a 10 µF tantalum capacitor in parallel with a 0.1 µF

ceramic capacitor may also improve noise.

Care should be taken to ensure that the connection from the

ADXL343 ground to the power supply ground has low impedance

because noise transmitted through ground has an effect similar

to noise transmitted through VS. It is recommended that VS and

VDD I/O be separate supplies to minimize digital clocking noise

on the VS supply. If this is not possible, additional filtering of

the supplies, as previously mentioned, may be necessary.

ADXL343

GND

INT1

INT2 CS

SCL/SCLK

SDO /ALT ADDRES S

SDA/SDI/SDIO 3- OR 4-WIRE

SPI OR I

INTERFACE

DD I/O

INTERRUPT

CONTROL

10627-016

Figure 34. Application Diagram

MECHANICAL CONSIDERATIONS FOR MOUNTING

The ADXL343 should be mounted on the PCB in a location

close to a hard mounting point of the PCB to the case. Mounting

the ADXL343 at an unsupported PCB location, as shown in

Figure 35, may result in large, apparent measurement errors

due to undampened PCB vibration. Locating the accelerometer

near a hard mounting point ensures that any PCB vibration at

the accelerometer is above the accelerometer’s mechanical sensor

resonant frequency and, therefore, effectively invisible to the

accelerometer. Multiple mounting points close to the sensor

and/or a thicker PCB also help to reduce the effect of system

resonance on the performance of the sensor.

MOUNTING POINTS

PCB

ACCELEROMETERS

10627-036

Figure 35. Incorrectly Placed Accelerometers

TAP DETECTION

The tap interrupt function is capable of detecting either single

or double taps. The following parameters are shown in Figure 36

for a valid single and valid double tap event:

• The tap detection threshold is defined by the THRESH_TAP

• The maximum tap duration time is defined by the DUR

• The tap latency time is defined by the latent register

(Address 0x22) and is the waiting period from the end

of the first tap until the start of the time window, when a

second tap can be detected, which is determined by the

value in the window register (Address 0x23).

• The interval after the latency time (set by the latent register) is

defined by the window register. Although a second tap must

begin after the latency time has expired, it need not finish

before the end of the time defined by the window register.

FIRST TAP

TIME LIMIT FOR

TAP S ( DUR)

LATENCY

TIME

(LATENT)

TIME WINDOW FOR

SECOND TAP ( WI NDOW )

SECOND TAP

SINGLE TAP

INTERRUPT DOUBL E TAP

INTERRUPT

THRESHOLD

(THRESH_TAP)

HI BW

INTERRUPTS

10627-037

Figure 36. Tap Interrupt Function with Valid Single and Double Taps

If only the single tap function is in use, the single tap interrupt

is triggered when the acceleration goes below the threshold, as

long as DUR has not been exceeded. If both single and double

tap functions are in use, the single tap interrupt is triggered

when the double tap event has been either validated or

invalidated.

Data Sheet ADXL343

Rev. 0 | Page 27 of 36

Several events can occur to invalidate the second tap of a double

tap event. First, if the suppress bit in the TAP_AXES register

(Address 0x2A) is set, any acceleration spike above the threshold

during the latency time (set by the latent register) invalidates

the double tap detection, as shown in Figure 37.

INV ALIDATES DOUBL E TAP IF

SUPRESS BIT SET

TIME WINDOW FOR SECOND

TAP ( WINDOW )

LATENCY

TIME (LATENT)

TIME LIMIT

FOR TAPS

(DUR)

HI BW

10627-038

Figure 37. Double Tap Event Invalid Due to High g Event

When the Suppress Bit Is Set

A double tap event can also be invalidated if acceleration above

the threshold is detected at the start of the time window for the

second tap (set by the window register). This results in an invalid

double tap at the start of this window, as shown in Figure 38.

Additionally, a double tap event can be invalidated if an accel-

eration exceeds the time limit for taps (set by the DUR register),

resulting in an invalid double tap at the end of the DUR time

limit for the second tap event, also shown in Figure 38.

INV ALIDATES DOUBL E TAP

AT START OF WINDOW

TIME WINDOW FOR

SECOND TAP ( WI NDOW )

LATENCY

TIME

(LATENT)

INVALIDATES

DOUBLE T AP AT

END O F DUR

TIME LIMIT

FOR TAPS

(DUR)

TIME LIMIT

FOR TAPS

(DUR)

TIME LIMIT

FOR TAPS

(DUR)

HI BW

10627-039

Figure 38. Tap Interrupt Function with Invalid Double Taps

Single taps, double taps, or both can be detected by setting the

respective bits in the INT_ENABLE register (Address 0x2E).

Control over participation of each of the three axes in single tap/

double tap detection is exerted by setting the appropriate bits in

the TAP_AXES register (Address 0x2A). For the double tap

function to operate, both the latent and window registers must

be set to a nonzero value.

Every mechanical system has somewhat different single tap/

double tap responses based on the mechanical characteristics of

the system. Therefore, some experimentation with values for the

DUR, latent, window, and THRESH_TAP registers is required.

In general, a good starting point is to set the DUR register to a

value greater than 0x10 (10 ms), the latent register to a value greater

than 0x10 (20 ms), the window register to a value greater than

0x40 (80 ms), and the THRESH_TAP register to a value greater

than 0x30 (3 g). Setting a very low value in the latent, window, or

THRESH_TAP register may result in an unpredictable response

due to the accelerometer picking up echoes of the tap inputs.

After a tap interrupt has been received, the first axis to exceed

the THRESH_TAP level is reported in the ACT_TAP_STATUS

overwritten with new data.

THRESHOLD

The lower output data rates are achieved by decimating a common

sampling frequency inside the device. The activity, free-fall, and

single tap/double tap detection functions without improved tap

enabled are performed using undecimated data. Because the

bandwidth of the output data varies with the data rate and is

lower than the bandwidth of the undecimated data, the high

frequency and high g data that is used to determine activity,

free-fall, and single tap/double tap events may not be present

if the output of the accelerometer is examined. This may result

in functions triggering when acceleration data does not appear

to meet the conditions set by the user for the corresponding

function.

LINK MODE

The function of the link bit is to reduce the number of activity

interrupts that the processor must service by setting the device

to look for activity only after inactivity. For proper operation of

this feature, the processor must still respond to the activity and

inactivity interrupts by reading the INT_SOURCE register

(Address 0x30) and, therefore, clearing the interrupts. If an activity

interrupt is not cleared, the part cannot go into autosleep mode.

The asleep bit in the ACT_TAP_STATUS register (Address 0x2B)

indicates if the part is asleep.

ADXL343 Data Sheet

Rev. 0 | Page 28 of 36

SLEEP MODE VS. LOW POWER MODE

In applications where a low data rate and low power consumption

is desired (at the expense of noise performance), it is recommended

that low power mode be used. The use of low power mode preserves

the functionality of the DATA_READY interrupt and FIFO for

postprocessing of the acceleration data. Sleep mode, while

offering a low data rate and power consumption, is not intended

for data acquisition.

However, when sleep mode is used in conjunction with the

AUTO_SLEEP mode and the link mode, the part can automatically

switch to a low power, low sampling rate mode when inactivity

is detected. To prevent the generation of redundant inactivity

interrupts, the inactivity interrupt is automatically disabled

and activity is enabled. When the ADXL343 is in sleep mode, the

host processor can also be placed into sleep mode or low power

mode to save significant system power. When activity is detected,

the accelerometer automatically switches back to the original

data rate of the application and provides an activity interrupt

that can be used to wake up the host processor. Similar to when

inactivity occurs, detection of activity events is disabled and

inactivity is enabled.

OFFSET CALIBRATION

Accelerometers are mechanical structures containing elements

that are free to move. These moving parts can be very sensitive

to mechanical stresses, much more so than solid-state electronics.

The 0 g bias or offset is an important accelerometer metric because

it defines the baseline for measuring acceleration. Additional

stresses can be applied during assembly of a system containing

an accelerometer. These stresses can come from, but are not

limited to, component soldering, board stress during mounting,

and application of any compounds on or over the component. If

calibration is deemed necessary, it is recommended that calibration

be performed after system assembly to compensate for these effects.

A simple method of calibration is to measure the offset while

assuming that the sensitivity of the ADXL343 is as specified in

Table 1. The offset can then be automatically accounted for by

using the built-in offset registers. This results in the data acquired

from the DATA registers already compensating for any offset.

In a no-turn or single-point calibration scheme, the part is oriented

such that one axis, typically the z-axis, is in the 1 g field of gravity

and the remaining axes, typically the x- and y-axis, are in a 0 g

field. The output is then measured by taking the average of a

series of samples. The number of samples averaged is a choice of

the system designer, but a recommended starting point is 0.1 sec

worth of data for data rates of 100 Hz or greater. This corresponds

to 10 samples at the 100 Hz data rate. For data rates less than

100 Hz, it is recommended that at least 10 samples be averaged

together. These values are stored as X0g, Y0g, and Z+1g for the 0 g

measurements on the x- and y-axis and the 1 g measurement on

the z-axis, respectively.

The values measured for X0g and Y0g correspond to the x- and y-axis

offset, and compensation is done by subtracting those values from

the output of the accelerometer to obtain the actual acceleration:

XACTUAL = XMEAS − X0g

YACTUAL = YMEAS − Y0g

Because the z-axis measurement was done in a +1 g field, a no-turn

or single-point calibration scheme assumes an ideal sensitivity,

SZ for the z-axis. This is subtracted from Z+1g to attain the z-axis

offset, which is then subtracted from future measured values to

obtain the actual value:

Z0g = Z+1g − SZ

ZACTUAL = ZMEAS − Z0g

The ADXL343 can automatically compensate the output for offset

by using the offset registers (Register 0x1E, Register 0x1F, and

value that is automatically added to all measured acceleration

values, and the result is then placed into the DATA registers.

Because the value placed in an offset register is additive, a negative

value is placed into the register to eliminate a positive offset and

vice versa for a negative offset. The register has a scale factor of

15.6 mg/LSB and is independent of the selected g-range.

As an example, assume that the ADXL343 is placed into full-

resolution mode with a sensitivity of typically 256 LSB/g. The

part is oriented such that the z-axis is in the field of gravity and

x-, y-, and z-axis outputs are measured as +10 LSB, −13 LSB,

and +9 LSB, respectively. Using the previous equations, X0g is

+10 LSB, Y0g is −13 LSB, and Z0g is +9 LSB. Each LSB of output

in full-resolution is 3.9 mg or one-quarter of an LSB of the

offset register. Because the offset register is additive, the 0 g

values are negated and rounded to the nearest LSB of the offset

XOFFSET = −Round(10/4) = −3 LSB

YOFFSET = −Round(−13/4) = 3 LSB

ZOFFSET = −Round(9/4) = −2 LSB

These values are programmed into the OFSX, OFSY, and OFXZ

registers, respectively, as 0xFD, 0x03, and 0xFE. As with all

registers in the ADXL343, the offset registers do not retain the

value written into them when power is removed from the part.

Power-cycling the ADXL343 returns the offset registers to their

default value of 0x00.

Because the no-turn or single-point calibration method assumes an

ideal sensitivity in the z-axis, any error in the sensitivity results in

offset error. For instance, if the actual sensitivity was 250 LSB/g

in the previous example, the offset would be 15 LSB, not 9 LSB.

To help minimize this error, an additional measurement point

can be used with the z-axis in a 0 g field and the 0 g measurement

can be used in the ZACTUAL equation.

Data Sheet ADXL343

Rev. 0 | Page 29 of 36

USING SELF-TEST

The self-test change is defined as the difference between the

acceleration output of an axis with self-test enabled and the

acceleration output of the same axis with self-test disabled (see

Endnote 4 of Table 1). This definition assumes that the sensor

does not move between these two measurements. If the sensor

moves, the additional shift, which is unrelated to self-test,

corrupts the test.

Proper configuration of the ADXL343 is also necessary for an

accurate self-test measurement. The part should be set with a

data rate of 100 Hz through 800 Hz, or 3200 Hz. This is done by

ensuring that a value of 0x0A through 0x0D, or 0x0F is written

into the rate bits (Bit D3 through Bit D0) in the BW_RATE

normal power operation by ensuring the LOW_POWER bit in

the BW_RATE register is cleared (LOW_POWER bit = 0) for

accurate self-test measurements. It is recommended that the

part be set to full-resolution, 16 g mode to ensure that there is

sufficient dynamic range for the entire self-test shift. This is done

by setting Bit D3 of the DATA_FORMAT register (Address 0x31)

and writing a value of 0x03 to the range bits (Bit D1 and Bit D0) of

the DATA_FORMAT register (Address 0x31). This results in a high

dynamic range for measurement and a 3.9 mg/LSB scale factor.

After the part is configured for accurate self-test measurement,

several samples of x-, y-, and z-axis acceleration data should be

retrieved from the sensor and averaged together. The number

of samples averaged is a choice of the system designer, but a

recommended starting point is 0.1 sec worth of data for data

rates of 100 Hz or greater. This corresponds to 10 samples at

the 100 Hz data rate. For data rates less than 100 Hz, it is

recommended that at least 10 samples be averaged together. The

averaged values should be stored and labeled appropriately as

the self-test disabled data, that is, XST_OFF, YST_OFF, and ZST_OFF.

Next, self-test should be enabled by setting Bit D7 (SELF_TEST) of

the DATA_FORMAT register (Address 0x31). The output needs

some time (about four samples) to settle after enabling self-test.

After allowing the output to settle, several samples of the x-, y-,

and z-axis acceleration data should be taken again and averaged. It

is recommended that the same number of samples be taken for

this average as was previously taken. These averaged values should

again be stored and labeled appropriately as the value with self-

test enabled, that is, XST_ON, YST_ON, and ZST_ON. Self-test can then be

disabled by clearing Bit D7 (SELF_TEST) of the DATA_FORMAT

With the stored values for self-test enabled and disabled, the

self-test change is as follows:

XST = XST_ON − XST_OFF

YST = YST_ON − YST_OFF

ZST = ZST_ON − ZST_OFF

Because the measured output for each axis is expressed in LSBs,

XST, YST, and ZST are also expressed in LSBs. These values can be

converted to g’s of acceleration by multiplying each value by the

3.9 mg/LSB scale factor, if configured for full-resolution mode.

Additionally, Table 15 through Table 18 correspond to the self-test

range converted to LSBs and can be compared with the measured

self-test change when operating at a VS of 2.5 V. For other voltages,

the minimum and maximum self-test output values should be

adjusted based on (multiplied by) the scale factors shown in

Table 14. If the part was placed into ±2 g, 10-bit or full-resolution

mode, the values listed in Table 15 should be used. Although

the fixed 10-bit mode or a range other than 16 g can be used, a

different set of values, as indicated in Table 16 through Table 18,

would need to be used. Using a range below 8 g may result in

insufficient dynamic range and should be considered when

selecting the range of operation for measuring self-test.

If the self-test change is within the valid range, the test is considered

successful. Generally, a part is considered to pass if the minimum

magnitude of change is achieved. However, a part that changes

by more than the maximum magnitude is not necessarily a failure.

Another effective method for using the self-test to verify accel-

erometer functionality is to toggle the self-test at a certain rate

and then perform an FFT on the output. The FFT should have a

corresponding tone at the frequency the self-test was toggled.

Using an FFT like this removes the dependency of the test on

supply voltage and on self-test magnitude, which can vary within

a rather wide range.

ADXL343 Data Sheet

Rev. 0 | Page 30 of 36

DATA FORMATTING OF UPPER DATA RATES

Formatting of output data at the 3200 Hz and 1600 Hz output

data rates changes depending on the mode of operation (full-

resolution or fixed 10-bit) and the selected output range.

When using the 3200 Hz or 1600 Hz output data rates in full-

resolution or ±2 g, 10-bit operation, the LSB of the output data-

word is always 0. When data is right justified, this corresponds

to Bit D0 of the DATAx0 register, as shown in Figure 39. When

data is left justified and the part is operating in ±2 g, 10-bit mode,

the LSB of the output data-word is Bit D6 of the DATAx0 register.

In full-resolution operation when data is left justified, the location

of the LSB changes according to the selected output range.

For a range of ±2 g, the LSB is Bit D6 of the DATAx0 register;

for ±4 g, Bit D5 of the DATAx0 register; for ±8 g, Bit D4 of the

DATAx0 register; and for ±16 g, Bit D3 of the DATAx0 register.

This is shown in Figure 40.

The use of 3200 Hz and 1600 Hz output data rates for fixed

10-bit operation in the ±4 g, ±8 g, and ±16 g output ranges

provides an LSB that is valid and that changes according to the

applied acceleration. Therefore, in these modes of operation,

Bit D0 is not always 0 when output data is right justified and

Bit D6 is not always 0 when output data is left justified.

Operation at any data rate of 800 Hz or lower also provides

a valid LSB in all ranges and modes that changes according

to the applied acceleration.

0D1D2D3D4D5D6D7

D0D1D2D3D4D5D6D7

DATAx1 RE GIS TER DATAx0 RE GIS TER

OUTPUT DATA-WO RD FO R

±16g, FULL-RESOLUTION MODE. OUTPUT DATA-WO RD FO R ALL

10-BI T MO DE S AND THE ± 2 g,

FULL-RESOLUTION MODE.

THE ±4 g AND ±8g FULL-RESOLUTION MODES HAVE THE SAME LSB LOCATION AS THE ±2g

AND ±16g FULL-RESOLUTION MODES, BUT THE MSB LOCATION CHANGES TO BIT D2 AND

BIT D3 OF T HE DATAX1 RE GI S TER F OR ±4gAND ±8g, RESPECTIVELY.

10627-145

Figure 39. Data Formatting of Full-Resolution and ±2 g, 10-Bit Modes of Operation When Output Data Is Right Justified

0D1D2D3D4D5D6D7

D0D1D2

D3D4D5D6D7

D0D1D2D3D4

D5D6D7

D0D1D2D3D4D5D6D7

DATAx1 RE GIS TER DATAx0 RE GIS TER

MSB FOR ALL MODES

OF OPERATION WHEN

LEFT JUSTIFIED.

LSB FOR ±2g, FULL-RESOLUTION

AND ±2g, 10- BIT M ODES .

LSB FOR ±4g, FULL-RESOLUTION MODE.

LSB FOR ±8g, FULL-RESOLUTION MODE.

LS B FOR ± 16g, FULL-RESOLUTION MODE.

FOR 3200Hz AND 1600Hz OUT P UT DAT A RATES , THE LSB IN T HE S E M ODES IS AL WAYS 0.

ADDITIONAL LY, ANY BITS TO THE RIG HT OF T HE LSB ARE ALW AY S 0 WHEN THE O UTPUT

DATA IS LEFT JUSTIFIED.

10627-146

Figure 40. Data Formatting of Full-Resolution and ±2 g, 10-Bit Modes of Operation When Output Data Is Left Justified

Data Sheet ADXL343

Rev. 0 | Page 31 of 36

NOISE PERFORMANCE

The specification of noise shown in Table 1 corresponds to

the typical noise performance of the ADXL343 in normal power

operation with an output data rate of 100 Hz (LOW_POWER bit

(D4) = 0, rate bits (D3:D0) = 0xA in the BW_RATE register,

Address 0x2C). For normal power operation at data rates below

100 Hz, the noise of the ADXL343 is equivalent to the noise at

100 Hz ODR in LSBs. For data rates greater than 100 Hz, the

noise increases roughly by a factor of √2 per doubling of the data

rate. For example, at 400 Hz ODR, the noise on the x- and y-axes

is typically less than 1.5 LSB rms, and the noise on the z-axis is

typically less than 2.2 LSB rms.

For low power operation (LOW_POWER bit (D4) = 1 in the

BW_RATE register, Address 0x2C), the noise of the ADXL343

is constant for all valid data rates shown in Table 8. This value is

typically less than 1.8 LSB rms for the x- and y-axes and typically

less than 2.6LSB rms for the z-axis.

The trend of noise performance for both normal power and low

power modes of operation of the ADXL343 is shown in Figure 41.

Figure 42 shows the typical Allan deviation for the ADXL343.

The 1/f corner of the device, as shown in this figure, is very low,

allowing absolute resolution of approximately 100 µg (assuming

that there is sufficient integration time). Figure 42 also shows

that the noise density is 290 µg/√Hz for the x-axis and y-axis

and 430 µg/√Hz for the z-axis.

Figure 43 shows the typical noise performance trend of the

ADXL343 over supply voltage. The performance is normalized

to the tested and specified supply voltage, VS = 2.5 V. In general,

noise decreases as supply voltage is increased. It should be noted, as

shown in Figure 41, that the noise on the z-axis is typically higher

than on the x-axis and y-axis; therefore, while they change roughly

the same in percentage over supply voltage, the magnitude of change

on the z-axis is greater than the magnitude of change on the

x-axis and y-axis.

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

3.13 6.25 12.50 25 50 100 200 400 800 1600 3200

OUTPUT DATA RATE (Hz)

OUTPUT NOI S E ( LSB rms)

X-AXIS, NORMAL POWER

X-AXIS, LO W PO W ER

Y-AXIS, NORMAL POWER

Y-AXIS, L O W PO W ER

Z-AXIS, NORMAL POWER

Z-AXIS, LOW POWER

10627-250

Figure 41. Noise vs. Output Data Rate for Normal and Low Power Modes,

Full-Resolution (256 LSB/g)

0.01

0.1 110 100 1k 10k

100

10k

AVE RAGI NG PERIO D, (s)

ALLAN DEVIATION (µg)

X-AXIS

Y-AXIS

Z-AXIS

10627-251

Figure 42. Root Allan Deviation

100

110

120

130

2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6

SUPPLY VOLTAGE, VS (V)

PERCENTAGE OF NORMALIZED NOISE (%)

X-AXIS

Y-AXIS

Z-AXIS

10627-252

Figure 43. Normalized Noise vs. Supply Voltage, VS

OPERATION AT VOLTAGES OTHER THAN 2.5 V

The ADXL343 is tested and specified at a supply voltage of

VS = 2.5 V; however, it can be powered with VS as high as 3.6 V

or as low as 2.0 V. Some performance parameters change as the

supply voltage changes: offset, sensitivity, noise, self-test, and

supply current.

Due to slight changes in the electrostatic forces as supply voltage

is varied, the offset and sensitivity change slightly. When operating

at a supply voltage of VS = 3.3 V, the x- and y-axis offset is typically

25 mg higher than at Vs = 2.5 V operation. The z-axis is typically

20 mg lower when operating at a supply voltage of 3.3 V than when

operating at VS = 2.5 V. Sensitivity on the x- and y-axes typically

shifts from a nominal 256 LSB/g (full-resolution or ±2 g, 10-bit

operation) at VS = 2.5 V operation to 265 LSB/g when operating

with a supply voltage of 3.3 V. The z-axis sensitivity is unaffected by

a change in supply voltage and is the same at VS = 3.3 V operation

as it is at VS = 2.5 V operation. Simple linear interpolation can be

used to determine typical shifts in offset and sensitivity at other

supply voltages.

ADXL343 Data Sheet

Rev. 0 | Page 32 of 36

Changes in noise performance, self-test response, and supply

current are discussed elsewhere throughout the data sheet. For

noise performance, the Noise Performance section should be

reviewed. The Using Self-Test section discusses both the

operation of self-test over voltage, a square relationship with

supply voltage, as well as the conversion of the self-test response

in g’s to LSBs. Finally, Figure 23 shows the impact of supply

voltage on typical current consumption at a 100 Hz output data

rate, with all other output data rates following the same trend.

OFFSET PERFORMANCE AT LOWEST DATA RATES

The ADXL343 offers a large number of output data rates and

bandwidths, designed for a large range of applications. However,

at the lowest data rates, described as those data rates below 6.25 Hz,

the offset performance over temperature can vary significantly

from the remaining data rates. Figure 44, Figure 45, and Figure 46

show the typical offset performance of the ADXL343 over

temperature for the data rates of 6.25 Hz and lower. All plots

are normalized to the offset at 100 Hz output data rate; therefore,

a nonzero value corresponds to additional offset shift due to

temperature for that data rate.

When using the lowest data rates, it is recommended that the

operating temperature range of the device be limited to provide

minimal offset shift across the operating temperature range.

Due to variability between parts, it is also recommended that

calibration over temperature be performed if any data rates

below 6.25 Hz are in use.

100

120

140

25 35 45 55 65 75 85

NORMALIZED OUTPUT (LSB)

TEMPERAT URE ( °C)

0.10Hz

0.20Hz

0.39Hz

0.78Hz

1.56Hz

3.13Hz

6.25Hz

10627-056

Figure 44. Typical X-Axis Output vs. Temperature at Lower Data Rates,

Normalized to 100 Hz Output Data Rate, VS = 2.5 V

100

120

140

25 35 45 55 65 75 85

NORMALIZED OUTPUT (LSB)

TEMPERAT URE ( °C)

0.10Hz

0.20Hz

0.39Hz

0.78Hz

1.56Hz

3.13Hz

6.25Hz

10627-057

Figure 45. Typical Y-Axis Output vs. Temperature at Lower Data Rates,

Normalized to 100 Hz Output Data Rate, VS = 2.5 V

–20

100

120

140

25 35 45 55 65 75 85

NORMALIZED OUTPUT (LSB)

TEMPERAT URE ( °C)

0.10Hz

0.20Hz

0.39Hz

0.78Hz

1.56Hz

3.13Hz

6.25Hz

10627-058

Figure 46. Typical Z-Axis Output vs. Temperature at Lower Data Rates,

Normalized to 100 Hz Output Data Rate, VS = 2.5 V

Data Sheet ADXL343

Rev. 0 | Page 33 of 36

AXES OF ACCELERATION SENSITIVITY

10627-021

Figure 47. Axes of Acceleration Sensitivity (Corresponding Output Voltage Increases When Accelerated Along the Sensitive Axis)

GRAVITY

OUT

= 1g

OUT

= 0g

OUT

= 0g

TOP

OUT

= –1g

OUT

= 0g

OUT

= 0g

TOP

OUT

= 0g

OUT

= 1g

OUT

= 0g

TOP

OUT

= 0g

OUT

= –1g

OUT

= 0g

TOP

OUT

= 0g

OUT

= 0g

OUT

= 1g

OUT

= 0g

OUT

= 0g

OUT

= –1g

10627-022

Figure 48. Output Response vs. Orientation to Gravity

ADXL343 Data Sheet

Rev. 0 | Page 34 of 36

LAYOUT AND DESIGN RECOMMENDATIONS

Figure 49 shows the recommended printed wiring board land pattern. Figure 50 and Table 24 provide details about the recommended

soldering profile.

3.3400

0.5500

0.2500

3.0500

0.2500

1.1450

5.3400

1.0500

10627-014

Figure 49. Recommended Printed Wiring Board Land Pattern (Dimensions shown in millimeters)

25°C TO P E AK

PREHEAT

CRITICAL ZONE

TO T

TEMPERATURE

TIME

RAMP-DOWN

RAMP-UP

SMIN

SMAX

10627-015

Figure 50. Recommended Soldering Profile

Table 24. Recommended Soldering Profile1, 2

Condition

Profile Feature Sn63/Pb37 Pb-Free

Average Ramp Rate from Liquid Temperature (TL) to Peak Temperature (TP) 3°C/sec maximum 3°C/sec maximum

Preheat

Minimum Temperature (TSMIN) 100°C 150°C

Maximum Temperature (TSMAX) 150°C 200°C

Time from TSMIN to TSMAX (tS) 60 sec to 120 sec 60 sec to 180 sec

TSMAX to TL Ramp-Up Rate 3°C/sec maximum 3°C/sec maximum

Liquid Temperature (TL) 183°C 217°C

Time Maintained Above TL (tL) 60 sec to 150 sec 60 sec to 150 sec

Peak Temperature (T

)

240 + 0/−5°C

260 + 0/−5°C

Time of Actual TP − 5°C (tP) 10 sec to 30 sec 20 sec to 40 sec

Ramp-Down Rate 6°C/sec maximum 6°C/sec maximum

Time 25°C to Peak Temperature 6 minutes maximum 8 minutes maximum

1 Based on JEDEC Standard J-STD-020D.1.

2 For best results, the soldering profile should be in accordance with the recommendations of the manufacturer of the solder paste used.

Data Sheet ADXL343

Rev. 0 | Page 35 of 36

OUTLINE DIMENSIONS

BOTTOM VIEW

TOP VIEW

END VIEW

SEATING

PLANE

1.00

0.95

0.85

5.00

BSC

3.00

BSC

PAD A1

CORNER

0.79

0.74

0.69

0.80

BSC

1.01

1.50

0.49

0.50

0.49 0.813 ×0.50

03-16-2010-A

Figure 51. 14-Terminal Land Grid Array [LGA]

(CC-14-1)

Solder Terminations Finish Is Au over Ni

Dimensions shown in millimeters

ORDERING GUIDE

Model1

Measurement

Range (g)

Specified

Voltage (V) Temperature Range Package Description

Package

Option

ADXL343BCCZ ±2, ±4, ±8, ±16 2.5 −40°C to +85°C 14-Terminal Land Grid Array [LGA] CC-14-1

ADXL343BCCZ-RL ±2, ±4, ±8, ±16 2.5 −40°C to +85°C 14-Terminal Land Grid Array [LGA] CC-14-1

ADXL343BCCZ-RL7 ±2, ±4, ±8, ±16 2.5 −40°C to +85°C 14-Terminal Land Grid Array [LGA] CC-14-1

EVAL-ADXL343Z Breakout Board

EVAL-ADXL343Z-DB Datalogger and Development Board

EVAL-ADXL343Z-M Analog Devices Inertial Sensor Evaluation

System, Includes ADXL343 Satellite

EVAL-ADXL343Z-S ADXL343 Satellite Only

1 Z = RoHS Compliant Part.

ADXL343 Data Sheet

Rev. 0 | Page 36 of 36

NOTES

I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).

Analog Devices offers specific products designated for automotive applications; please consult your local Analog Devices sales representative for details. Standard products sold by

Analog Devices are not designed, intended, or approved for use in life support, implantable medical devices, transportation, nuclear, safety, or other equipment where malfunction

of the product can reasonably be expected to result in personal injury, death, se

vere property damage, or severe environmental harm. Buyer uses or sells standard products for use

in the above critical applications at Buyer's own risk and Buyer agrees to defend, indemnify, and hold harmless Analog Devices from any and all damages, claims, suits, or expenses

resulting from such unintended use.

registered trademarks are the property of their respective owners.

D10627-0-4/12(0)

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

ADXL343BCCZ-RL7 EVAL-ADXL343Z-M ADXL343BCCZ EVAL-ADXL343Z ADXL343BCCZ-RL EVAL-ADXL343Z-

S EVAL-ADXL343Z-DB