Chip tantalum capacitors Datasheet TC series P case Features 1) Small package, large capacitance chip tantalum capacitor. 2) Low impedance capacitors. 3) Screening by thermal shock. Dimensions Unit(mm) Anode mark L Dimensions Size L 2.00.2 W1 1.250.20 W2 0.90.2 H MAX.1.20 S 0.450.30 W1 H W2 S S - + Part No. Explanation T C P 1 A Series name TC Case code P2012-12(0805)size Rated voltage Code 0E 0G 0J Rated voltage(V) 2.5 4 6.3 1A 1B 1C 1D 1E 1V 10 13 16 20 25 35 www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. 1 0 5 M 8 R Nominal capacitance Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. Capacitance tolerance M20% Taping 8Real width8mm RPositive electrode on the side opposite to sprocket hole 1/7 2019.05.08 - Rev.002 Datasheet TC series P case Rated table Capacitance Rated voltage(V.DC) (F) 4 6.3 1.0 (105) 2.2 (225) 10 16 P P P P P P P P P P P 20 25 35 P 3.3 (335) 4.7 (475) 10 (106) 15 (156) 22 (226) 33 (336) 47 (476) 100 (107) Remark) Case size codes ( P ) in the above show products line-up. Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : A voltage code is shown as below table. (3) Capacitance : A capacitance code is shown as below table. Voltage Code e g j A C D E V Rated DC Voltage (V) 2.5 4 6.3 10 16 20 25 35 Capacitance Code N S A E J N S a Nominal Capacitance (F) 0.33 0.47 1.0 1.5 2.2 3.3 4.7 10 Capacitance Code e j n s a e j n Nominal Capacitance (F) 15 22 33 47 100 150 220 330 Visual typical example voltage code and capacitance code are variable with parts number. [TC series P case] EX. A (1) A (2) AA (1) voltage code (2) capacitance code www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. manufacture code 2/7 2019.05.08 - Rev.002 TC series P case Datasheet Characteristics Item Test condition Performance Operating temperature -55+125 Maximum operating +85 (Based on JIS C 5101-1JIS C 5101-3) Voltage reduction when temperature exceeds +85 temperature with no voltage derating. Rated voltage(V.DC) Refer to " Standard list ". at 85 Category voltage(V.DC) Refer to " Standard list ". at 125 Surge voltage(V.DC) Refer to " Standard list ". at 85 DC leakage current Shall be satisfied the value on " Standard list ". As per 4.9 JIS C 5101-1-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1min. Capacitance tolerance Tangent of loss angle Shall be satisfied allowance range. As per 4.7 JIS C 5101-1 20% As per 4.5.2 JIS C 5101-3 Shall be satisfied the value on " Standard list ". (Df,tan) Measuring frequency : 120+12Hz Measuring voltage : 0.5Vrms+1.5V.DC Measuring circuit : DC equivalent series circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Impedance Shall be satisfied the value on " Standard list ". Measuring frequency : 120+12Hz Measuring voltage : 0.5Vrms+1.5V.DC Measuring circuit : DC equivalent series circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Resistance App- to soldering arance heat L.C. C/C DF Temperature cycle arance L.C. : 120+12Hz Measuring voltage : 0.5Vrms+1.5V.DC Measuring circuit : DC equivalent series circuit There should be no significant abnormality. As per 4.14 JIS C 5101-1 The indications should be clear. As per 4.6 JIS C 5101-3 Less than 200% of initial limit. Dip in the solder bath. Within 20% of initial limit. Less than 200% of initial limit. Solder temp. : 26010 Duration : 50.5s Repetition :1 After the specimens, leave it at room temperature (tan) App- Measuring frequency for over 24h and then measure the sample. There should be no significant abnormality. As per 4.16 JIS C 5101-1 The indications should be clear. As per 4.10 JIS C 5101-3 Less than 200% of initial limit. Repetition : 5cycles (1cycle:steps1~4)Without discontinuation C/C Within 20% of initial limit. Temp. DF Less than 200% of initial limit. (tan) Time 1 -553 303min 2 Room temp. 3min or less 3 1252 303min 4 Room temp. 3min or less After the specimens, leave it at room temperature for over 24h and then measure the sample. www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. 3/7 2019.05.08 - Rev.002 TC series P case Datasheet Item Moisture resistance Test condition Performance Apparance L.C. (Based on JIS C 5101-1JIS C 5101-3) There should be no significant abnormality. As per 4.22 JIS C 5101-1 The indications should be clear. As per 4.12 JIS C 5101-3 Less than 200% of initial limit. After leaving the sample under such atmospheric Within 20% of initial limit. 602 and 90~95%(Relative Humidity) , Less than 200% of initial limit. temperature for over 24h and then measure the condition that the temperature and humidity are C/C respectively ,for 50024h leave it at room DF (tan) Temperature sample. Temp : -55 As per 4.29 JIS C 5101-1 C/C Within 0/-15% of initial limit. tan Shall be satisfied the value on " Standard list ". L.C. - As per 4.13 JIS C 5101-3 Temp : +85 C/C Within +15/0% of initial limit. tan Shall be satisfied the value on " Standard list ". L.C. Less than 1000% of initial limit. Temp : +125 Surge voltage C/C Within +20/0% of initial limit. tan Shall be satisfied the value on " Standard list ". L.C. Less than 1250% of initial limit. App- There should be no significant abnormality. As per 4.26 JIS C 5101-1 The indications should be clear. As per 4.14 JIS C 5101-3 Less than 200% of initial limit. Apply the specified serge voltage via the serial Within 20% of initial limit. time in the atmospheric condition of 852. Less than 200% of initial limit. specimens, leave it at room temperature for over There should be no significant abnormality. As per 4.23 JIS C 5101-1 The indications should be clear. As per 4.15 JIS C 5101-3 Less than 200% of initial limit. After applying the rated voltage for 1000+72/0h arance L.C. resistance of 1k ever 50.5min for 305s each C/C Repeat this procedure 1,000 times. After the DF (tan) Loading at high temperature Apparance L.C. 24h and then measure the sample. without discontinuation via the serial resistance C/C Within 20% of initial limit. of 3or less at a temperature of 852 , leave the sample at room temperature/humidity for DF Less than 200% of initial limit. over 24h and measure the value. (tan) www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. 4/7 2019.05.08 - Rev.002 Datasheet TC series P case Item Test condition Performance Terminal Capa- strength citance App- (Based on JIS C 5101-1JIS C 5101-3) The measured value should be stable. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 There should be no significant abnormality. arance A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintains the Unit(mm) 20 50 F(Apply force) R230 1.0mm thickness=1.6mm 45 Adhesiveness The terminal should not come off. 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in he figure below for 101s after mounting the terminal on a circuit board. Products Apply force A circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 class 2 or higher grade. Resistance to solvents The indication should be clear. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 305s , at room temperature. Solder ability 3/4 or more surface area of the solder As per 4.15.2 JIS C 5101-1 coated terminal dipped in the soldering As per 4.7 JIS C 5101-3 bath should be covered with the new Dip speed : 252.5mm/s solder. Pre-treatment : Leave the sample on the boiling (accelerated aging) Solder temp : 2455 Duration : 30.5s Solder : M705 Flux : Rosin 25% IPA 75% Vibration Capa- Measure value should not fluctuate As per 4.17 JIS C 5101-1 citance during the measurement. Frequency App- There should be no significant abnormality. arance : 105510Hz/min. Amplitude : 1.5mm Time : 2h each in X,Y and Z directions. Mounting : The terminal is soldered on a print circuit board. www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. 5/7 2019.05.08 - Rev.002 TC series P case Datasheet Standard products list Part No Rated Category Surge voltage voltage voltage 85 105 85 Cap. Tole- Leakage rance current 120Hz tan 25 1WV 120Hz -55 1min (V) (V) (V) Impedance 25 100kHz 125 85 (F) (%) (A) (%) (%) (%) () 9.3 TCP0G106M8R 4 2.5 5 10 20 0.5 30 20 30 TCP0G226M8R 4 2.5 5 22 20 0.9 30 20 30 7.7 TCP0J225M8R 6.3 4 8 2.2 20 0.5 30 20 30 17.5 TCP0J475M8R 6.3 4 8 4.7 20 0.5 30 20 30 11.8 TCP0J106M8R 6.3 4 8 10 20 0.6 30 20 30 8.3 TCP0J226M8R 6.3 4 8 22 20 1.4 38 25 38 5.0 TCP1A105M8R 10 6.3 13 1.0 20 0.5 15 10 15 17.5 TCP1A225M8R 10 6.3 13 2.2 20 0.5 30 20 30 14.4 TCP1A475M8R 10 6.3 13 4.7 20 0.5 30 20 30 9.3 TCP1A106M8R 10 6.3 13 10 20 1.0 30 20 30 7.7 TCP1C105M8R 16 10 20 1.0 20 0.5 15 10 15 16.1 TCP1E105M8R 25 16 32 1.0 20 0.6 30 20 30 9.3 www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. 6/7 2019.05.08 - Rev.002 Datasheet TC series P case Packaging specifications Sprocket hole Do t1 E A F B W t2 Component is loaded. P1 P2 Pull-out direction PO Unit(mm) A B W E F P1 1.550.10 2.300.10 8.000.20 1.750.10 3.500.05 4.000.10 PO DO t1 t2 standard packaging quantity 4.000.10 1.550.05 0.250.05 1.320.10 3,000pcs P2 2.000.05 9.0+1.0/0 Reel dimensions Label www.rohm.com (c) 2019 ROHM Co.,Ltd.All rights reserved. Pull-out direction 180+0/-1.5 60+1.0/0 130.2 11.41.0 EIAJ ET-7200A 7/7 2019.05.08 - Rev.002 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet TCP0J226M8R - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS TCP0J226M8R TCP 3000 3000 Taping inquiry Yes