FTR-K1 SERIES POWER RELAY 1 POLE - 5A Relay Type FTR-F2 Series n FEATURES High density mounting Saves space by 26% compared to FTR-H1 type. l High insulation Insulation distance between coil and contacts: 6mm Dielectric Strength: 4KV Surge Strength: 10KV l Flux proof type, RTII l Flammability 94V-0 l Cadmium free contact for eco-program l SAFETY STANDARDS UL, CSA, VDE, SEMKO approved UL/CSA TV-5 rating approved l RoHS Compliant Please see page 5 for more information l n PARTNUMBER INFORMATION [Example] FTR-F2 (a) A (b) K (c) 012 (d) T (e) (a) Relay type FTR-F2 : FTR-F2-Series (b) Contact configuration A : 1 form A (SPST-NO) K L : Standard type (530mW) : High sensitivity type (250mW) (c) Coil type / enclosure (d) Coil rated voltage 012 (e) Contact material T : 5.....48 VDC Coil rating table at page 3 : Silver tin oxide / TV-5 Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-F2AK012T Actual marking: F2AK012T 1 FTR-K1 SERIES FTR-F2 SERIES n SPECIFICATION Item Contact Data Life Timing Data Insulation F2 AK ( ) T F2 AL ( ) T 1 form A (SPST-NO) Construction Single Material Silver tin oxide (AgSnO2) Resistance (initial) Max. 100 m at 6 VDC, 1 A Contact rating 5A, 250VAC / 30VDC Max. carrying current 5A Max. switching voltage 400VAC / 300 VDC Max. switching power 1,250VA / 150A Min. switching load * 100 mA, 5 VDC Mechanical Min. 2 x 106 operations AC contact rating Min. 100 x 103 operations DC contact rating Min.100 x 103 operations Lamp load (TV-5) Min. 25 x 103 operations Rated power (at 20 C) 530mW 250mW Operate power (at 20 C) 260mW 160mW Operating temperature range -40 C to +70 C (no frost) Operate (at nominal voltage) Max. 15 ms Release (at nominal voltage) Max. 5 ms Resistance (initial) Min. 1,000M at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 4,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50s standard wave Clearance 6mm Creepage 6mm EN61810-1, VDE0435 Other Sensitive Configuration Electrical Coil Data Standard Vibration Resistance Shock Voltage 250V Pollution degree 2 Material group III a Category B / 250V Misoperation 10 to 55Hz double amplitude 1.5mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation Min. 200m/s (11 1ms) Endurance Min. 1,000m/s (6 1ms) Weight Approximately 12g Sealing Flux proof RTII * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-F2 SERIES n COIL RATING Standard Type (530mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Max. Coil Voltage (VDC) 005 5 47 3.5 0.25 8.5 006 6 68 4.2 0.3 10.2 009 9 155 6.3 0.45 15.3 012 12 270 8.4 0.6 20.4 018 18 610 12.6 0.9 30.6 024 24 1,110 16.8 1.2 40.8 048 48 4,400 33.6 2.4 81.6 Rated Power (mW) 530 Sensitive Type (250mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Max. Coil Voltage (VDC) 005 5 100 4 0.25 12.5 006 6 145 4.8 0.3 15 009 9 325 7.2 0.45 22.5 012 12 575 9.6 0.6 30 024 24 2,310 19.2 1.2 60 Rated Power (mW) 250 Note: All values in the tables are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63614 CSA C22.2 No. 14 LR 40304 VDE 0435, 0860 SEMKO 5A, 30 VDC/250VAC (resistive) 1/6 HP, 125VAC 1/2 HP, 250VAC TV-5, 120 VAC Pilot duty: C300 40014652 5A, 250VAC (cos 1) 2A, 250VAC (cos 0.4) 5A, 30VDC (0ms) EN 61058-1: 1992 and A1 EN 61095:1993 and A1+A11 250 VAC, 5 (1) or 5/80 40T70 Complies with CQC, NEMKO, DEMKO, FIMKO 3 FTR-K1 SERIES FTR-F2 SERIES n CHARACTERISTIC DATA n DIMENSIONS l Dimensions Unit: mm l Schematics l PC board mounting hole layout (BOTTOM VIEW) 4 FTR-K1 SERIES FTR-F2 SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 5 FTR-K1 SERIES FTR-F2 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2012 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. March 28, 2012 6