CHEMTRONICS TDS # 1603 Technical Data Sheet Electro-Wash PR PRODUCT DESCRIPTION Electro-Wash PR is a fast drying, one step degreasing agent and cleaner that is safe for most plastics. Engineered with very low surface tension, this high pressure aerosol formulation flushes areas clean and evaporates instantly leaving no residue. Removes oxides, dust, dirt, and grease Penetrates hard to reach areas Evaporates quickly Leaves no residues Has low odor Noncorrosive Contains no CFCs, HCFCs or 1,1,1 Trichloroethane Contains no Chlorinated Solvents TYPICAL APPLICATIONS Electro-Wash PR removes grease, oils and other soils from: Printed Circuit Boards Relays and Contacts Fuse Boxes TVs / VCRs Solder Paste Screens Timers Wire Harnesses Plastic Housings TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES Boiling Point 141F Initial Dielectric Strength 24 Kv Flash Point (TCC) -20.0F Appearance Clear Colorless Liquid Odor Solubility in Water Mild Negligible Specific Gravity (water = 1@68F) 0.67 Evaporation Rate (butyl acetate=1) <1 Surface Tension (dynes/cm @21.6C) 18.3 Kauri-Butanol (KB) Number Shelflife 50 5 years COMPATIBILITY Electro-Wash PR is generally compatible with most materials used in printed circuit board fabrication, except acrylics, ABS resins, polycarbonates and polystyrenes. As with any cleaning agent solvent/component compatibility must be determined on a noncritical area prior to use. Material ABS Buna-N EPDM Graphite HDPE LDPE Lexan Neoprene Noryl Nylon 66 Cross-Linked PE Polypropylene Polystyrene PVC Silicone Rubber Teflon Viton Compatibility Non-Compatible Fair Fair Excellent Excellent Good Fair Fair Poor Excellent Excellent Excellent Non-Compatible Excellent Poor Excellent Fair COMPETITIVE ASSESSMENT Milligrams of Lithium Greased Removed Per 7 Second Spray 1,000 _ _ 800 _ 823 _ 600 _ _ 400 _ _ 200 _ 67% Better Cleaning 493 299 0 Chemtronics Electro-Wash PR Tech Spray Blue Shower MicroCare 2004 USAGE INSTRUCTIONS For commercial use only. Read MSDS carefully prior to use. Spray 4 to 6 inches from surface to clean. Wash parts from top to bottom, allowing the liquid to flush away dirt and dissolved grease. For precise application use attached extension tube. Flammable Do Not near sources or ignition or energized equipment. AVAILABILITY ES1603 10 oz. Aerosol TECHNICAL & APPLICATION ASSISTANCE Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401. ENVIRONMENTAL IMPACT DATA ENVIRONMENTAL IMPACT DATA CFC HCFC CL Solv. 0.0% 0.0% 0.0% VOC HFC ODP 91.0% 0.0% 0.00 CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown are the content by weight. Ozone depletion potential (ODP) is determined in accordance with the Montreal Protocol and U.S. Clean Air Act of 1990. The ODP of this product is 0.10. It is the sum of the ODP of the substances that may contribute to the depletion of stratospheric ozone, based upon the weight of each substance in the product's formulation. NOTE: This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it. MANUFACTURED BY: ITW CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 1-770-424-4888 REV. C (03/01) DISTRIBUTED BY: