GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc -5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Features RoHS Compliant Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 Compliant to REACH Directive (EC) No 1907/2006 Delivers up to 3A output current High efficiency - 94% at 3.3V full load (VIN = 5.0V) Small size and low profile: 20.3 mm x 11.4 mm x 7.27 mm (0.80 in x 0.45 in x 0.286 in) Low output ripple and noise High Reliability: Calculated MTBF = 11.9M hours at 25oC Full-load Applications Constant switching frequency (300 kHz) Output voltage programmable from 0.75 Vdc to 3.63Vdc via external resistor Distributed power architectures Intermediate bus voltage applications Line Regulation: 0.4% (typical) Telecommunications equipment Load Regulation: 0.4% (typical) Servers and storage applications Temperature Regulation: 0.4 % (typical) Networking equipment Remote On/Off Enterprise Networks Output overcurrent protection (non-latching) Latest generation IC's (DSP, FPGA, ASIC) and Microprocessor powered applications Wide operating temperature range (-40C to 85C) ANSI/UL* 62368-1 and CAN/ CSA C22.2 No. 62368-1 Recognized, DIN VDE 0868-1/A11:2017 (EN623681:2014/A11:2017) ISO** 9001 and ISO 14001 certified manufacturing facilities Description Austin MiniLynxTM SMT (surface mount technology) power modules are non-isolated dc-dc converters that can deliver up to 3A of output current with full load efficiency of 94.0% at 3.3V output. These modules provide a precisely regulated output voltage programmable via an external resistor from 0.75Vdc to 3.63Vdc over a wide range of input voltage (VIN = 2.4 - 5.5Vdc). Their open-frame construction and small footprint enable designers to develop cost- and space-efficient solutions. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards February 16, 2021 (c)2015 General Electric Company. All rights reserved. GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Device Symbol Min Max Unit All VIN -0.3 5.8 Vdc All TA -40 85 C All Tstg -55 125 C Continuous Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit 2.4 5.5 Vdc 3.0 Adc Operating Input Voltage VO,set VIN - 0.5V VIN Maximum Input Current All IIN,max VO,set = 0.75Vdc IIN,No load 10 mA VO,set = 3.3Vdc IIN,No load 17 mA All IIN,stand-by 0.6 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 35 mAp-p Input Ripple Rejection (120Hz) All 30 dB (VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc) Input No Load Current (VIN = 5.0Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.0Vdc, module disabled) 0.04 A2s CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data sheet for further information. February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 2 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -2.0 VO, set +2.0 % VO, set All VO, set -3% +3% % VO, set All VO 0.7525 3.63 Vdc (VIN=IN, min, IO=IO, max, TA=25C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All 0.4 % VO, set Load (IO=IO, min to IO, max) All 0.4 % VO, set Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set RMS (5Hz to 20MHz bandwidth) All 10 15 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All 25 50 mVpk-pk Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1F ceramic//10Ftantalum capacitors) External Capacitance ESR 1 m All CO, max 1000 F ESR 10 m All CO, max 5000 F Output Current All Io 0 3 Adc Output Current Limit Inception (Hiccup Mode ) All IO, lim 220 % Io All IO, s/c 2 Adc 81.5 % VIN= VIN, nom, TA=25C VO,set = 0.75Vdc VO, set = 1.2Vdc 87.0 % IO=IO, max , VO= VO,set VO,set = 1.5Vdc 89.0 % VO,set = 1.8Vdc 90.0 % VO,set = 2.5Vdc 93.0 % (VO= 90% of VO, set) Output Short-Circuit Current (VO250mV) ( Hiccup Mode ) Efficiency VO,set = 3.3Vdc All fsw 300 kHz All Vpk 250 mV Settling Time (Vo<10% peak deviation) All ts 50 s (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 100% to 50%of Io,max: 1F ceramic// 10 F tantalum Peak Deviation All Vpk 250 mV Settling Time (Vo<10% peak deviation) All ts 50 s Switching Frequency 94.0 % Dynamic Load Response (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 50% to 100% of Io,max; 1F ceramic// 10 F tantalum Peak Deviation February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 3 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit (dIo/dt=2.5A/s; V VIN = VIN, nom; TA=25C) Load Change from Io= 50% to 100% of Io,max; Co = 2x150 F polymer capacitors Peak Deviation All Vpk 60 mV Settling Time (Vo<10% peak deviation) All ts 100 s (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 100% to 50%of Io,max: Co = 2x150 F polymer capacitors Peak Deviation All Vpk 60 mV Settling Time (Vo<10% peak deviation) All ts 100 s Dynamic Load Response General Specifications Parameter Min Calculated MTBF (IO=IO, max, TA=25C) Weight February 16, 2021 Typ Max 11,965,153 2.8 (0.1) (c)2015 General Electric Company. All rights reserved. Unit Hours g (oz.) Page 4 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit Input High Voltage (Module ON) All VIH VIN, max V Input High Current All IIH 10 A Input Low Voltage (Module OFF) All VIL -0.2 0.3 V Input Low Current All IIL 0.2 1 mA Input High Voltage (Module OFF) All VIH 1.5 Input High Current All IIH Input Low Voltage (Module ON) All VIL Input low Current All IIL All Tdelay All All On/Off Signal interface Device code with Suffix "4" - Positive logic (On/Off is open collector/drain logic input; Signal referenced to GND - See feature description section) Device Code with no suffix - Negative Logic (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) VIN,max Vdc 0.2 1 mA 0.3 Vdc 10 A 3.9 msec Tdelay 3.9 msec Trise 4.2 8.5 msec 1 % VO, set 0.5 140 -0.2 Turn-On Delay and Rise Times (IO=IO, max , VIN = VIN, nom, TA = 25 oC, ) Case 1: On/Off input is set to Logic Low (Module ON) and then input power is applied (delay from instant at which VIN =VIN, min until Vo=10% of Vo,set) Case 2: Input power is applied for at least one second and then the On/Off input is set to logic Low (delay from instant at which Von/Off=0.3V until Vo=10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo,set to 90% of Vo, set) Output voltage overshoot - Startup IO= IO, max; VIN = 3.0 to 5.5Vdc, TA = 25 Remote Sense Range Overtemperature Protection oC All Tref C (See Thermal Consideration section) Input Undervoltage Lockout Turn-on Threshold All 2.2 V Turn-off Threshold All 2.0 V February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 5 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Characteristic Curves The following figures provide typical characteristics for the Austin MiniLynxTM SMT modules at 25C. 94 97 91 94 91 EFFICIENCY, (%) EFFICIENCY, (%) 88 85 82 79 VIN = 2.5V 76 VIN = 3.3V 73 88 85 82 VIN = 2.5V 79 VIN = 3.3V 76 VIN = 5.0V VIN = 5.0V 73 70 0 0.6 1.2 1.8 2.4 0 3 0.6 OUTPUT CURRENT, IO (A) 2.4 3 Figure 4. Converter Efficiency versus Output Current (Vout = 1.8Vdc). 94 98 91 95 88 92 EFFICIENCY, (%) EFFICIENCY, (%) 1.8 OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current (Vout = 0.75Vdc). 85 82 79 VIN = 2.5V 76 VIN = 3.3V 73 VIN = 5.0V 89 86 83 VIN = 3.3V 80 VIN = 4.0V 77 VIN = 5.0V 70 74 0 0.6 1.2 1.8 2.4 3 0 0.6 OUTPUT CURRENT, IO (A) 99 93 96 90 93 EFFICIENCY, (%) 87 84 VIN = 2.5V 78 VIN = 3.3V 75 VIN = 5.0V 0.6 1.2 1.8 3 2.4 90 87 84 VIN = 4.0V 81 VIN = 5.0V 78 3 75 0 0.6 OUTPUT CURRENT, IO (A) Figure 3. Converter Efficiency versus Output Current (Vout = 1.5Vdc). February 16, 2021 2.4 VIN = 5.5V 72 0 1.8 Figure 5. Converter Efficiency versus Output Current (Vout = 2.5Vdc). 96 81 1.2 OUTPUT CURRENT, IO (A) Figure 2. Converter Efficiency versus Output Current (Vout = 1.2Vdc). EFFICIENCY, (%) 1.2 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 6. Converter Efficiency versus Output Current (Vout = 3.3Vdc). (c)2015 General Electric Company. All rights reserved. Page 6 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the Austin MiniLynxTM SMT modules at 25C. 3.5 1 0.5 0 3 4 INPUT VOLTAGE, VIN (V) VO (V) (10mV/div) OUTPUT VOLTAGE Figure 8. Typical Output Ripple and Noise (VIN = 5.0V dc, Vo = 0.75Vdc, Io=3A). TIME, t (1s/div) Figure 9. Typical Output Ripple and Noise (VIN = 5.0V dc, Vo = 3.3Vdc, Io=3A). February 16, 2021 OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (1s/div) TIME, t (20 s/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3Vdc). TIME, t (20 s/div) Figure 11. Transient Response to Dynamic Load Change from 100% to 50% of full load (Vo = 3.3 Vdc). OUTPUT CURRENT, OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE Figure 7. Input voltage vs. Input Current (Vout =2.5Vdc). 5 VO (V) (100mV/div) 2 IO (A) (2A/div) 1 VO (V) (20mV/div) 0 IO (A) (2A/div) 1.5 OUTPUT CURRENT, OUTPUT VOLTAGE Io=0A 2 IO (A) (2A/div) INPUT CURRENT, IIN (A) Io=1.5A 2.5 VO (V) (100mV/div) Io=3A 3 TIME, t (100s/div) Figure 12. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3 Vdc, Cext = 2x150 F Polymer Capacitors). (c)2015 General Electric Company. All rights reserved. Page 7 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Characteristic Curves (continued) VO (V) (0.5V/div) TIME, t (2ms/div) Figure 17 Typical Start-Up Using Remote On/Off with Prebias (VIN = 3.3Vdc, Vo = 1.8Vdc, Io = 1.0A, Vbias =1.0Vdc). OUTPUT CURRENT, VO (V) (1V/div) VOn/off(V) (2V/div) OUTPUT VOLTAGE Figure 14. Typical Start-Up Using Remote On/Off (VIN = 5.0Vdc, Vo = 3.3Vdc, Io = 3A). ON/OFF VOLTAGE INPUT VOLTAG OUTPUT VOLTAGE VO (V) (1V/div) (V) (2V/div) ON/OFF VOLTAGE TIME, t (2ms/div) TIME, t (2ms/div) TIME, t (10ms/div) Figure 15. Typical Start-Up Using Remote On/Off with Low- ESR external capacitors (7x150uF Polymer) (VIN = 5.0Vdc, Vo = 3.3Vdc, Io = 3A, Co = 1050F). February 16, 2021 Figure 16. Typical Start-Up with application of Vin (VIN = 5.0Vdc, Vo = 3.3Vdc, Io = 3A). OUTPUT VOLTAGE VO (V) (1V/div) VOn/off(V) (2V/div) ON/OFF VOLTAGE OUTPUT VOLTAGE Figure 13. Transient Response to Dynamic Load Change from 100% of 50% full load (Vo = 3.3Vdc, Cext = 2x150 F Polymer Capacitors). TIME, t (2ms/div) VOn/off(V) (2V/div) TIME, t (100s/div) IO (A) (5A/div) OUTPUT CURRENT, OUTPUTVOLTAGE VO (V) (20mV/div) IO (A) (2A/div) VIN The following figures provide typical characteristics for the Austin MiniLynxTM SMT modules at 25C. Figure 18. Output short circuit Current (VIN = 5.0Vdc, Vo = 0.75Vdc). (c)2015 General Electric Company. All rights reserved. Page 8 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Characteristic Curves (continued) 3.5 3.5 3 3 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) The following figures provide thermal derating curves for the Austin MiniLynxTM SMT modules. 2.5 2 1.5 1 0.5 0 LFM 2.5 2 1.5 1 0.5 0 LFM 0 0 20 30 40 50 60 70 80 20 90 30 AMBIENT TEMPERATURE, TA OC OUTPUT CURRENT, Io (A) Figure 19. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 5.0, Vo=3.3Vdc). 50 60 70 80 90 Figure 22. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 3.3dc, Vo=2.5 Vdc). 3.5 3.5 3 3 2.5 2.5 2 2 1.5 1.5 1 1 0.5 0.5 0 LFM 0 LFM 0 0 20 30 40 50 60 70 AMBIENT TEMPERATURE, TA 80 20 90 30 40 50 60 70 80 90 OC Figure 20. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 5.0Vdc, Vo=1.8 Vdc). OUTPUT CURRENT, Io (A) 40 AMBIENT TEMPERATURE, TA OC Figure 23. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 3.3dc, Vo=1.2 Vdc). 3.5 3.5 3 3 2.5 2.5 2 2 1.5 1.5 1 1 0.5 0.5 0 LFM 0 LFM 0 0 20 30 40 50 60 70 80 90 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA OC Figure 21. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 5.0Vdc, Vo=0.75 Vdc). Figure 24. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 3.3dc, Vo=0.75 Vdc). Test Configurations February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 9 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current CURRENT PROBE TO OSCILLOSCOPE LTEST BATTERY Input Filtering VIN(+) 1H The Austin MiniLynxTM SMT module should be connected to a low-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. CIN CS 1000F Electrolytic 2x100F Tantalum E.S.R.<0.1 Design Considerations @ 20C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 25. Input Reflected Ripple Current Test Setup. To minimize input voltage ripple, low-ESR polymer and ceramic capacitors are recommended at the input of the module. Figure 28 shows the input ripple voltage (mVp-p) for various outputs with 1x22F (TDK: C3225X5R0J226V) ceramic capacitor at the input of the module. Figure 29 shows the input ripple with 1x47F (TDK: C3225X5R0J476M) ceramic capacitor at full load. COPPER STRIP 160 3.3Vin VO (+) RESISTIVE LOAD . 10uF Input Ripple Voltage (mVp-p) 1uF 140 SCOPE COM GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 26. Output Ripple and Noise Test Setup. 5Vin 120 100 80 60 40 20 0 0 Rdistribution Rcontact Rcontact VIN(+) 0.5 1 VO 2 2.5 3 3.5 Output Voltage (Vdc) RLOAD VO VIN 1.5 Rdistribution Figure 28. Input ripple voltage for various outputs with 1x22 F ceramic capacitor at the input (full-load). 160 Rcontact Rcontact COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 27. Output Voltage and Efficiency Test Setup. VO. IO Efficiency = VIN. IIN x 100 % 3.3Vin Rdistribution COM 140 Input Ripple Voltage (mVp-p) Rdistribution 5Vin 120 100 80 60 40 20 0 0 0.5 1 1.5 2 2.5 3 3.5 Output Voltage (Vdc) Figure 29. Input ripple voltage for various outputs with 1x47 F ceramic capacitor at the input (full load). February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 10 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Design Considerations (continued) Safety Considerations Output Filtering For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL ANSI/UL62368-1 and CAN/CSA C22.2 No. 62368-1 Recognized, DIN VDE 0868-1/A11:2017 (EN62368-1:2014/A11:2017). MiniLynxTM The Austin SMT module is designed for low output ripple voltage and will meet the maximum output ripple specification with 1 F ceramic and 10 F tantalum capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. February 16, 2021 For the converter output to be considered meeting the Requirements of safety extra-low voltage (SELV) or ES1, the input must meet SELV/ES1 requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a fast-acting fuse with a maximum rating of 6A in the positive input lead. (c)2015 General Electric Company. All rights reserved. Page 11 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Feature Description VIN+ Remote On/Off The Austin MiniLynxTM SMT power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available in the Austin MiniLynxTM series modules. Positive Logic On/Off signal, device code suffix "4", turns the module ON during a logic High on the On/Off pin and turns the module OFF during a logic Low. Negative logic On/Off signal, no device code suffix, turns the module OFF during logic High on the On/Off pin and turns the module ON during logic Low. For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 30. The On/Off pin is an open collector/drain logic input signal (Von/Off) that is referenced to ground. During a logic-high (On/Off pin is pulled high internal to the module) when the transistor Q1 is in the Off state, the power module is ON. Maximum allowable leakage current of the transistor when Von/off = VIN,max is 10A. Applying a logic-low when the transistor Q1 is turnedOn, the power module is OFF. During this state VOn/Off must be less than 0.3V. When not using positive logic On/off pin, leave the pin unconnected or tie to VIN. VIN+ MODULE R2 ON/O FF + I ON/OFF I ON/OFF ON/O FF + VON/OFF PWM Ena ble R1 Q2 CSS Q1 R2 GND _ Figure 31. Circuit configuration for using negative logic On/OFF. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The typical average output current during hiccup is 2A. Input Undervoltage Lockout Q2 R1 VON/OFF PWM Ena ble R3 At input voltages below the input undervoltage lockout limit, module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Overtemperature Protection Q1 Q3 CSS R4 GND MODULE Rpull-up _ Figure 30. Circuit configuration for using positive logic On/OFF. For negative logic On/Off devices, the circuit configuration is shown is Figure 31. The On/Off pin is pulled high with an external pull-up resistor (typical Rpull-up = 5k, +/- 5%). When transistor Q1 is in the Off state, logic High is applied to the On/Off pin and the power module is Off. The minimum On/off voltage for logic High on the On/Off pin is 1.5Vdc. To turn the module ON, logic Low is applied to the On/Off pin by turning ON Q1. When not using the negative logic On/Off, leave the pin unconnected or tie to GND. To provide over temperature protection in a fault condition, the unit relies upon the thermal protection feature of the controller IC. The unit will shutdown if the thermal reference point Tref, exceeds 140oC (typical), but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restart after it cools down. Output Voltage Programming The output voltage of the Austin MiniLynxTM SMT can be programmed to any voltage from 0.75 Vdc to 3.63 Vdc by connecting a single resistor (shown as Rtrim in Figure 32) between the TRIM and GND pins of the module. Without an external resistor between TRIM pin and the ground, the output voltage of the module is 0.7525 Vdc. To calculate the value of the resistor Rtrim for a particular output voltage Vo, use the following equation: 21070 Rtrim = - 5110 Vo - 0 . 7525 Feature Descriptions (continued) Output Voltage Programming (continued) February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 12 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current For example, to program the output voltage of the Austin MiniLynxTM module to 1.8 Vdc, Rtrim is calculated is follows: Vo Rmargin-d own 21070 Rtrim = - 5110 1.8 - 0.7525 Aust in Ly nx or Lynx II Se ries Rtrim = 15.004k Q2 Trim V IN(+) V O(+) Rmargin-u p Rtrim ON/OFF LOAD TRIM Q1 R trim GND GND Figure 32. Circuit configuration to program output voltage using an external resistor. Figure 33. Circuit Configuration for margining Output voltage. Table 1 provides Rtrim values required for some common output voltages. Table 1 VO, set (V) Rtrim (K) 0.7525 Open 1.2 41.973 1.5 23.077 1.8 15.004 2.5 6.947 3.3 3.160 Using 1% tolerance trim resistor, set point tolerance of 2% is achieved as specified in the electrical specification. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, helps determine the required external trim resistor needed for a specific output voltage. Voltage Margining Output voltage margining can be implemented in the Austin MiniLynxTM modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the Output pin for margining-down. Figure 33 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local GE technical representative for additional details. February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 13 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. 25.4_ (1.0) Wind Tunnel PWBs Power Mod ule Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 35. Note that the airflow is parallel to the long axis of the module as shown in figure 34. The derating data applies to airflow in either direction of the module's long axis. 76.2_ (3.0) x 5.97_ (0.235) Air Flow Prob e Loc a tion for mea suring a irflow a nd a mb ient temp era ture Air flow Figure 35. Thermal Test Set-up. Tref Figure 34. Tref Temperature measurement location. The thermal reference point, Tref used in the specifications is shown in Figure 34. For reliable operation this temperature should not exceed 115oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note "Thermal Characterization Process For Open-Frame Board-Mounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 14 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) BOTTOM VIEW SIDE VIEW Co-planarity (max): 0.102 [0.004] February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 15 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) PIN 1 FUNCTION On/Off 2 VIN 3 GND 4 Trim 5 VOUT February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 16 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Packaging Details The Austin MiniLynxTM SMT version is supplied in tape & reel as standard. Modules are shipped in quantities of 400 modules per reel. All Dimensions are in millimeters and (in inches). Reel Dimensions Outside diameter: 330.2 mm (13.00) Inside diameter: 177.8 mm (7.00") Tape Width: February 16, 2021 44.0 mm (1.73") (c)2015 General Electric Company. All rights reserved. Page 17 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Surface Mount Information The Austin MiniLynxTM SMT modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and placing. The label meets all the requirements for surface mount processing, as well as safety standards and is able to withstand maximum reflow temperature. The label also carries product information such as product code, serial number and location of manufacture. REFLOW TEMP ( C) Pick and Place REFLOW TIME (S) Figure 36. Pick and Place Location. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Even so, these modules have a relatively large mass when compared to conventional SMT components. Variables such as nozzle size, tip style, vacuum pressure and pick & placement speed should be considered to optimize this process. The minimum recommended nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 8 mm max. MAX TEMP SOLDER ( C) Figure 37. Reflow Profile for Tin/Lead (Sn/Pb) process. Figure 38. Time Limit Curve Above 205oC Reflow for Tin Lead (Sn/Pb) process. Tin Lead Soldering The Austin MiniLynxTM SMT power modules are lead free modules and can be soldered either in a lead-free solder process or a conventional Tin/Lead (Sn/Pb) process. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. The Austin MiniLynxTM SMT power modules are lead free modules and can be soldered either in a lead-free solder process or a conventional Tin/Lead (Sn/Pb) process. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. February 16, 2021 (c)2015 General Electric Company. All rights reserved. Page 18 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Lead Free Soldering The -Z version Austin MiniLynx SMT modules are lead-free (Pb-free) and RoHS compliant and are both forward and backward compatible in a Pb-free and a SnPb soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure. 39. MSL Rating The Austin MiniLynxTM SMT modules have a MSL rating of 2a. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). 300 Per J-STD-020 Rev. C Peak Temp 260C 250 200 * Min. Time Above 235C 15 Seconds 150 Heating Zone 1C/Second Cooling Zone *Time Above 217C 60 Seconds 100 50 Storage and Handling The Austin MiniLynxTM modules have a MSL rating of 1. The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in JSTD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken February 16, 2021 until time of use. Once the original package is broken, the floor life of the product at conditions of 30C and 60% relative humidity varies according to the MSL rating (see JSTD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40 C, < 90% relative humidity. Reflow Temp (C) Surface Mount Information (continued) 0 Reflow Time (Seconds) Figure 39. Recommended linear reflow profile using Sn/Ag/Cu solder. (c)2015 General Electric Company. All rights reserved. Page 19 GE Data Sheet Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 2.4Vdc - 5.5Vdc input; 0.75Vdc to 3.63Vdc output; 3A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 2. Device Codes Device Code Input Voltage Range Output Voltage Output Current Efficiency 3.3V@ 3A On/Off Logic Connector Type Comcodes AXH003A0X-SRZ 2.4 - 5.5Vdc 0.75 - 3.63Vdc 3A 94.0 % Negative SMT CC109101301 AXH003A0X4-SRZ 2.4 - 5.5Vdc 0.75 - 3.63Vdc 3A 94.0 % Positive SMT 109100014 -Z refers to RoHS-compliant codes Contact Us For more information, call us at USA/Canada: +1 877 546 3243, or +1 972 244 9288 Asia-Pacific: +86-21-53899666 Europe, Middle-East and Africa: +49.89.878067-280 Go.ABB/Industrial GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. February 16, 2021 (c)2015 General Electric Company. All International rights reserved. Version 1_2