Series RF312/RF332 DPDT Non-Latching Electromechanical Relay Signal Integrity up to 12Gbps HIGH REPEATABILITY, DC-8 GHz TO-5 RELAYS DPDT SERIES RELAY TYPE RF312 Repeatable, RF relay RF332 Sensitive Repeatable, RF relay DESCRIPTION CONSTRUCTION FEATURES The ultra miniature RF312 is designed to improve upon the RF300/RF303 relay's high frequency performance. The RF312/RF332 offers monotonic insertion loss to 8 GHz. This improvement in RF insertion loss over the frequency range, makes these relays highly suitable for use in attenuator and other RF circuits. The sensitive RF332 relay has a high resistance coil, thus requiring extremely low operating power (200 mW typical). The advantages of reduced heat dissipation and power supply demands are a plus. The RF312/RF332 features: The following unique construction features and manufacturing techniques provide excellent resistance to environmental extremes and overall high reliability. * Uni-frame motor design provides high magnetic efficiency and mechanical rigidity. * Minimum mass components and welded construction provide maximum resistance to shock and vibration. * Advanced cleaning techniques provide maximum assurance of internal cleanliness. * Gold-plated precious metal alloy contacts ensure reliable switching. * Hermetically sealed. * Solder-Dipped Leads, (RoHS compliant solder option available) * High repeatability. * Broader bandwidth. * Metal enclosure for EMI shielding. * Ground pin option to improve case grounding. * High isolation between control and signal paths. * Highly resistant to ESD. ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Temperature (Ambient) Storage -65C to +125C Operating -55C to +85C Vibration (General Note I) 10 g's to 500 Hz Shock (General Note I) 30 g's, 6ms half sine Enclosure Hermetically sealed Weight 0.09 oz. (2.55g) max. (c) 2011 TELEDYNE RELAYS INTERNAL CONSTRUCTION UNI-FRAME UPPER STATIONARY CONTACT ARMATURE (800) 284-7007 * www.teledynerelays.com MOVING CONTACT LOWER STATIONARY CONTACT RF312/RF332 Page 1 RF312/RF332\092011\Q3 Series RF312/RF332 DPDT Non-Latching Electromechanical Relay Signal Integrity up to 12Gbps, SERIES RF312/RF332 TYPICAL RF CHARACTERISTICS (See RF Notes) Isolation Across Contacts (RF Note 4) Isolation Pole to Pole (RF Note 5) 0 0 -10 Pole-Pole Isolation (dB) -10 Isolation (dB) -20 -30 -40 -30 -40 -50 De-Energized -60 Normally Open -50 -20 Energized Normally CLosed -70 -60 -80 0 1000 2000 3000 4000 5000 6000 7000 8000 0 1000 2000 3000 Frequency (MHz) Insertion Loss (RF Note 6) 5000 6000 7000 8000 VSWR (RF Note 6) 0 5 -0.5 4.5 -1 Normally CLosed 4 Normally Open -1.5 3.5 -2 VSWR Insertion Loss (dB) 4000 Frequency (MHz) -2.5 -3 3 2.5 -3.5 2 Normally Closed -4 Normally Open 1.5 -4.5 1 -5 0 1000 2000 3000 4000 5000 6000 7000 0 8000 1000 2000 3000 4000 5000 6000 7000 8000 Frequency (MHz) Frequency (MHz) RF312/RF332 Time Response (RF Note 6) 1.1 0.9 90% Volt 0.7 37ps reference 0.5 62.3ps propagation delay time 0.3 51.3ps pulse rise time 10% 0.1 -0.1 -100 0 100 200 300 400 500 600 700 800 900 Time (ps) RF NOTES a. Fixture: .031" copper clad, reinforced PTFE, RT/duroid(R) 6002 with SMA connectors. (RT/duroid(R) is a registered trademark of Rogers Corporation.) b. Room ambient temperature. c. Terminals not tested were terminated with 50-ohm load. d. Contact signal level: -10 dBm. e. No. of test samples: 4. Data presented herein represents typical characteristics and is not intended for use as specification limits. Data is per pole, except for pole-to-pole data. Data is the average from readings taken on all open contacts. Data is the average from readings taken on poles with coil energized and de-energized. Data is the average from readings taken on all closed contacts. Test fixture effect de-embedded from frequency and time response data. 1. Test conditions: 2. 3. 4. 5. 6. 7. RF312/RF332 Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2011 TELEDYNE RELAYS RF312/RF332\092011\Q3 Series RF312/RF332 DPDT Non-Latching Electromechanical Relay Signal Integrity up to 12Gbps SERIES RF312/RF332 GENERAL ELECTRICAL SPECIFICATIONS (@25C) Contact Arrangement 2 Form C (DPDT) Rated Duty Continuous Contact Resistance 0.15 max. Contact Load Rating Resistive: 1Amp/28Vdc Low level: 10 to 50 A @ 10 to 50 mV Contact Life Ratings 10,000,000 cycles (typical) at low level Coil Operating Power RF312: 450 mW typical at nominal rated voltage RF332: 200 mW typical at nominal rated voltage Operate Time RF312: 4.0 mS max. RF332: 6.0 mS max. Release Time 3.0 mS max. Intercontact Capacitance 0.4 pf typical Insulation Resistance 1,000 M min. between mutually isolated terminals Dielectric Strength 350 Vrms (60 Hz) @ atmospheric pressure DETAILED ELECTRICAL SPECIFICATIONS (@25C) BASE PART NUMBERS (RF312) RF312-5 RF312-12 5.0 12.0 Coil Resistance (Ohms 20%) 50 390 Pick-up Voltage (Vdc max.) 3.6 9.0 RF332-5 RF332-12 Coil Voltage, Nominal (Vdc) 5.0 12.0 Coil Resistance (Ohms 20%) 100 850 Pick-up Voltage (Vdc max.) 3.6 9.0 Coil Voltage, Nominal (Vdc) BASE PART NUMBERS (RF332) Teledyne Part Numbering System for RF312/RF332 RF312 X - 5 / S R Relay Series Q = Solder-Coated Leads1 G = Gold-Plated Leads (RoHS Compliant) R = RoHS Compliant Solder2 S = 0.187" Leads No Suffix = 0.75" Leads Ground Pin Option (See Appendix A) Nominal Coil Voltage General Note: Parts ordered without suffix may be supplied with Solder-Coated or Gold-Plated leads 1 Parts ordered with Solder-Coated leads will have (Sn60/Pb40) 2 Parts ordered with RoHS Solder-Coated leads will have (Sn99.3/Cu0.7) (c) 2011 TELEDYNE RELAYS (800) 284-7007 * www.teledynerelays.com RF312/RF332 Page 3 RF312/RF332\092011\Q3 Series RF312/RF332 DPDT Non-Latching Electromechanical Relay Signal Integrity up to 12Gbps, SERIES RF312/RF332 OUTLINE DIMENSIONS .400 MAX [ 10.16 ] (RF332) 9 1 8 2 3 7 6 4 SCHEMATIC DIAGRAM NOTES: 1. DIMENSIONS ARE IN INCHES, METRIC EQUIVALENTS SHOWN IN [ ]. 2. POSTITIONS 5 AND 10 ARE FOR UNINSULATED CASE GROUND OPTIONS. 3. NO PROTRUSION BELOW BOTTOM OF HEADER WHEN GROUND PINS ARE INSTALLED 4. TO ORDER THE CASE GROUND OPTION, AFTER THE SERIES DESIGNATOR, ADD "Y" TO THE PART NUMBER FOR POSITION 5 OR "Z" TO THE PART NUMBER FOR POSITION 10. GENERAL NOTES I. Relays will exhibit no contact chatter in excess of 10 sec or transfer in excess of 1 sec. II. For reference only. Coil resistance not directly measureable at relay terminals due to internal series diode. RF312/RF332 Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2011 TELEDYNE RELAYS RF312/RF332\092011\Q3 Series RF312/RF332 DPDT Non-Latching Electromechanical Relay Signal Integrity up to 12Gbps SERIES RF312/RF332 TYPICAL SIGNAL INTEGRITY CHARACTERISTICS Normally Closed (Typ.) +130 mV 0V -130 mV 0 ps 40 ps 80 ps 120 ps 160 ps Eye Height Eye Width SNR JitterP-P 272.2 mV 92.62 ps 20.76 6.22 ps Normally Open (Typ.) +130 mV 0V -130 mV 0 ps 40 ps 80 ps 120 ps 160 ps Eye Height Eye Width SNR JitterP-P 238.4 mV 92.82 ps 12.85 7.11 ps PATTERN GENERATOR SETTINGS * * * * * 10 Gbps Random Pulse Pattern Generator 231 - 1 PRBS signal PRBS output of 300 mVP-P (nominal) RF PCB effect (negligible) not removed from measurement Data shown is typical of both poles (c) 2011 TELEDYNE RELAYS (800) 284-7007 * www.teledynerelays.com RF312/RF332 Page 5 RF312/RF332\092011\Q3