SMA6J5.0A-Q - BOURNS - Product.Network

Features

n Surface Mount SMA package

n Standoff Voltage: 5 to 130 volts

n Power Dissipation: 600 watts

n RoHS compliant*

n AEC-Q101 compliant**

Applications

n Protection of power buses

n Protection of I/O interfaces

n Overvoltage transient protection

n Telecom, computer, industrial and

consumer electronics applications

Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted)

SMA6J-Q Transient Voltage Suppressor Diode Series

*RoHS Directive 2015/863, Mar 31, 2015 and Annex.

**”Q” part number sufﬁx indicates AEC-Q101 compliance.

Speciﬁcations are subject to change without notice.

Users should verify actual device performance in their speciﬁc applications.

The products described herein and this document are subject to speciﬁc legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

Parameter Symbol Value Unit

Minimum Peak Pulse Power Dissipation (TP = 1 ms) (Note 1,2) PPK 600 Watts

Peak Forward Surge Current

8.3 ms Single Half Sine Wave Superimposed on Rated Load

(JEDEC Method) (Note 3)

IFSM 40 Amps

Operating Temperature Range TJ-55 to +150 °C

Storage Temperature Range TSTG -55 to +150 °C

1. Non-repetitive current pulse, per Pulse Waveform graph and derated above TA = 25 °C per Pulse Derating Curve.

2. Mounted on 5.0 mm2 (0.03 mm thick) copper pads to each terminal.

3. 8.3 ms Single Half-Sine Wave duty cycle = 4 pulses maximum per minute (unidirectional units only).

General Information

Bourns offers Transient Voltage Suppressor Diodes for surge and ESD protection applications, in compact chip package DO-214AC (SMA)

size format. The Transient Voltage Suppressor series offers a choice of Working Peak Reverse Voltage from 5 V up to 130 V. Typical fast

response times are less than 1.0 picosecond from 0 V to Breakdown Voltage.

Bourns® Chip Diodes are easy to handle with standard pick and place equipment and the at conguration minimizes roll away.

WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Asia-Pacic: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com

EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com

The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com

www.bourns.com

*RoHS COMPLIANT

*RoHS &

**AEC-Q101 COMPLIANT

*RoHS COMPLIANT

AEC APPROVED (Select Models)

LEAD FREE

*RoHS COMPLIANT

VERSIONS

AVAILABLE

LEAD FREE

VERSIONS ARE

RoHS COMPLIANT*

AUTOMOTIVE

GRADE

Speciﬁcations are subject to change without notice.

Users should verify actual device performance in their speciﬁc applications.

The products described herein and this document are subject to speciﬁc legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

SMA6J-Q Transient Voltage Suppressor Diode Series

Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted) - Continued

Unidirectional Device Bidirectional Device Breakdown Voltage

VBR (Volts)

Working

Peak

Reverse

Voltage

Maximum

Reverse

Leakage

@ VRWM

Maximum

Reverse

Voltage

@ IRSM

Maximum

Reverse

Surge

Current

Part No. Marking Part No. Marking Min. Max. @ IT (mA) VRWM (V) IR (μA) VRSM (V) IRSM (A)

SMA6J5.0A-Q 6HEQ SMA6J5.0CA-Q 6TEQ 6.40 7.00 10 5.0 800 9.2 65.3

SMA6J6.0A-Q 6HGQ SMA6J6.0CA-Q 6TGQ 6.67 7.37 10 6.0 800 10.3 58.3

SMA6J6.5A-Q 6HKQ SMA6J6.5CA-Q 6TKQ 7.22 7.98 10 6.5 500 11.2 53.6

SMA6J7.0A-Q 6HMQ SMA6J7.0CA-Q 6TMQ 7.78 8.60 10 7.0 200 12.0 50.0

SMA6J7.5A-Q 6HPQ SMA6J7.5CA-Q 6TPQ 8.33 9.21 1.0 7.5 100 12.9 46.6

SMA6J8.0A-Q 6HRQ SMA6J8.0CA-Q 6TRQ 8.89 9.83 1.0 8.0 50 13.6 44.2

SMA6J8.5A-Q 6HTQ SMA6J8.5CA-Q 6TTQ 9.44 10.4 1.0 8.5 20 14.4 41.7

SMA6J9.0A-Q 6HVQ SMA6J9.0CA-Q 6TVQ 10.0 11.1 1.0 9.0 10 15.4 39.0

SMA6J10A-Q 6HXQ SMA6J10CA-Q 6TXQ 11.1 12.3 1.0 10 5 17.0 35.3

SMA6J11A-Q 6HZQ SMA6J11CA-Q 6TZQ 12.2 13.5 1.0 11 1.0 18.2 33.0

SMA6J12A-Q 6IEQ SMA6J12CA-Q 6UEQ 13.3 14.7 1.0 12 1.0 19.9 30.2

SMA6J13A-Q 6IGQ SMA6J13CA-Q 6UGQ 14.4 15.9 1.0 13 1.0 21.5 28.0

SMA6J14A-Q 6IKQ SMA6J14CA-Q 6UKQ 15.6 17.2 1.0 14 1.0 23.2 25.9

SMA6J15A-Q 6IMQ SMA6J15CA-Q 6UMQ 16.7 18.5 1.0 15 1.0 24.4 24.6

SMA6J16A-Q 6IPQ SMA6J16CA-Q 6UPQ 17.8 19.7 1.0 16 1.0 26.0 23.1

SMA6J17A-Q 6IRQ SMA6J17CA-Q 6URQ 18.9 20.9 1.0 17 1.0 27.6 21.8

SMA6J18A-Q 6ITQ SMA6J18CA-Q 6UTQ 20.0 22.1 1.0 18 1.0 29.2 20.6

SMA6J20A-Q 6IVQ SMA6J20CA-Q 6UVQ 22.2 24.5 1.0 20 1.0 32.4 18.6

SMA6J22A-Q 6IXQ SMA6J22CA-Q 6UXQ 24.4 26.9 1.0 22 1.0 35.5 16.9

SMA6J24A-Q 6IZQ SMA6J24CA-Q 6UZQ 26.7 29.5 1.0 24 1.0 38.9 15.5

SMA6J26A-Q 6JEQ SMA6J26CA-Q 6VEQ 28.9 31.9 1.0 26 1.0 42.1 14.3

SMA6J28A-Q 6JGQ SMA6J28CA-Q 6VGQ 31.1 34.4 1.0 28 1.0 45.4 13.3

SMA6J30A-Q 6JKQ SMA6J30CA-Q 6VKQ 33.3 36.8 1.0 30 1.0 48.4 12.4

SMA6J33A-Q 6JMQ SMA6J33CA-Q 6VMQ 36.7 40.6 1.0 33 1.0 53.3 11.3

SMA6J36A-Q 6JPQ SMA6J36CA-Q 6VPQ 40.0 44.2 1.0 36 1.0 58.1 10.4

SMA6J40A-Q 6JRQ SMA6J40CA-Q 6VRQ 44.4 49.1 1.0 40 1.0 64.5 9.3

SMA6J43A-Q 6JTQ SMA6J43CA-Q 6VTQ 47.8 52.8 1.0 43 1.0 69.4 8.7

SMA6J45A-Q 6JVQ SMA6J45CA-Q 6VVQ 50.0 55.3 1.0 45 1.0 72.7 8.3

SMA6J48A-Q 6JXQ SMA6J48CA-Q 6VXQ 53.3 58.9 1.0 48 1.0 77.4 7.8

SMA6J51A-Q 6JZQ SMA6J51CA-Q 6VZQ 56.7 62.7 1.0 51 1.0 82.4 7.3

SMA6J54A-Q 6KEQ SMA6J54CA-Q 6WEQ 60.0 66.3 1.0 54 1.0 87.1 6.9

SMA6J58A-Q 6KGQ SMA6J58CA-Q 6WGQ 64.4 71.2 1.0 58 1.0 93.6 6.5

SMA6J60A-Q 6KKQ SMA6J60CA-Q 6WKQ 66.7 73.7 1.0 60 1.0 96.8 6.2

SMA6J64A-Q 6KMQ SMA6J64CA-Q 6WMQ 71.1 78.6 1.0 64 1.0 103.0 5.9

SMA6J70A-Q 6KPQ SMA6J70CA-Q 6WPQ 77.8 86.0 1.0 70 1.0 113.0 5.3

SMA6J75A-Q 6KRQ SMA6J75CA-Q 6WRQ 83.3 92.1 1.0 75 1.0 121.0 5.0

SMA6J78A-Q 6KTQ SMA6J78CA-Q 6WTQ 86.7 95.8 1.0 78 1.0 126.0 4.8

SMA6J85A-Q 6KVQ SMA6J85CA-Q 6WVQ 94.4 104.0 1.0 85 1.0 137.0 4.4

SMA6J90A-Q 6KXQ SMA6J90CA-Q 6WXQ 100.0 111.0 1.0 90 1.0 146.0 4.1

SMA6J100A-Q 6KZQ 111.0 123.0 1.0 100 1.0 162.0 3.7

SMA6J110A-Q 6LEQ 122.0 135.0 1.0 110 1.0 177.0 3.4

SMA6J120A-Q 6LGQ 133.0 147.0 1.0 120 1.0 193.0 3.1

SMA6J130A-Q 6LKQ 144.0 159.0 1.0 130 1.0 209.0 2.9

Notes: 1. Sufx ‘A’ denotes a 5 % tolerance unidirectional device.

2. Sufx ‘CA’ denotes a 5 % tolerance bidirectional device.

3. For bidirectional devices with a VRWM of 10 volts or less, the IR limit is double.

3312 - 2 mm SMD Trimming Potentiometer

Speciﬁcations are subject to change without notice.

Users should verify actual device performance in their speciﬁc applications.

The products described herein and this document are subject to speciﬁc legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

SMA6J-Q Transient Voltage Suppressor Diode Series

Performance Graphs

100

050

25 75 100 175125 150

TA - Ambient Temperature (

Peak Pulse Power Derating in Percent of

Peak Power or Current

°C)

1.0

0.1

0.1 µs 1.0 µs 10 µs 10 ms

Td - Pulse Width (Seconds)

PPPM - Peak Pulse Power (kW)

100 µs 1.0 ms

5.0

(0.20)

5.0

(0.20)

x COPPER PAD AREAS

NON-REPETITIVE PULSE

WAVEFORM SHOWN IN

FIGURE 3 TA = 25 °C

100

150

0 1.0 2.0 3.0 4.0

t - Time (ms)

IPPM - Peak Pulse Current (% IRSM)

TA=25 °C

tr=10 µs

Peak value (IPPM)

Half value= IPPM

TJ = 25 °C

Pulse width (td)

is defined as the point

where the peak current

decays to 50 % of IPPM.

10/1000 µs waveform

as defined by R.E.A.

CJ - Junction Capacitance (pF)

10000

110 100 1000

VBR - Reverse Breakdown Voltage (V)

100

1000

TJ = 25 °C

f = 1.0 MHz

Vsig = 50 mVp-p

Unidirectional

@ VR

Bidirectional

@ VR

Bidirectional

v-0v

Unidirectional

v-0v

3.0

1.5

2.0

2.5

1.0

0.5

0.0

050

25 75 100 175125 150

TL - Lead Temperature (°C)

Steady State Power Dissipation (W)

IFSM - Peak Forward Surge Current (A)

110 100

Number of Cycles at 60 Hz

Unidirectional Only

Peak Pulse Power Rating Pulse Derating Curve

Pulse Waveform Typical Junction Capacitance

Steady State Power Derating Curve Maximum Non-repetitive Forward Surge Current

3312 - 2 mm SMD Trimming Potentiometer

Product Dimensions

Speciﬁcations are subject to change without notice.

Users should verify actual device performance in their speciﬁc applications.

The products described herein and this document are subject to speciﬁc legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

SMA6J-Q Transient Voltage Suppressor Diode Series

Recommended Footprint

Physical Specications

Case ...........................................Molded plastic per UL Class 94V-0

Polarity....................... Cathode band indicates unidirectional device

No cathode band indicates bidirectional device

DIMENSIONS: MM

(INCHES)

F D

(INCHES)

DIMENSIONS:

(INCHES)

DIMENSIONS:

Dimension SMA (DO-214AC)

A3.99 - 4.50

(0.157 - 0.177)

B2.54 - 2.79

(0.100 - 0.110)

C1.25 - 1.65

(0.049 - 0.065)

D0.15 - 0.31

(0.006 - 0.012)

E 4.93 - 5.28

(0.194 - 0.208)

F 0.203 MAX.

(0.008)

G 1.98 - 2.29

(0.078 - 0.090)

H 0.76 - 1.52

(0.030 - 0.060)

DIMENSIONS: MM

(INCHES)

Dimension SMA (DO-214AC)

A (Max.) 2.70

(0.106)

B (Min.) 2.10

(0.083)

C (Min.) 1.27

(0.050)

How to Order

SMA6J 5.0 CA - Q

Package

SMA6J = 600 W, SMA/DO-214AC

Working Peak Reverse Voltage

5.0 - 130 = 5.0 - 130 VRWM (Volts)

Sufx

A = 5 % Tolerance Unidirectional Device

CA = 5 % Tolerance Bidirectional Device

AEC-Q101 Sufx

Q = AEC-Q101 Compliant, 13-inch Reel

Typical Part Marking

YWW

XXXX

DATE CODE:

Y = LAST

DIGIT OF

YEAR

WW = WEEK

NUMBER

MANUFACTURER’S

TRADEMARK

DEVICE ID

Environmental Specications

Moisture Sensitivity Level ................................................................1

ESD Classication (HBM)............................................................. 3B

.......

....... ..............

P A

120 °

Index Hole

10 pitches (min.)

Direction of Feed

10 pitches (min.)

End

Trailer Device Leader

Start

CDDFN5-0504N - TVS/Steering Diode Array

Packaging Information

The product will be dispensed in tape and reel format (see diagram below).

Devices are packed as shown here in compliance with

EIA-481-C standard.

DIMENSIONS: MM

(INCHES)

REV. 10/20

Speciﬁcations are subject to change without notice.

Users should verify actual device performance in their speciﬁc applications.

The products described herein and this document are subject to speciﬁc legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

SMA6J-Q Transient Voltage Suppressor Diode Series

Item Symbol SMA (DO-214AC)

13-Inch Reel

Carrier Width A 2.90 ± 0.20

(0.114 ± 0.008)

Carrier Length B 5.50 ± 0.20

(0.217 ± 0.008)

Carrier Depth C 2.26 ± 0.20

(0.089 ± 0.008)

Sprocket Hole d 1.50 ± 0.10

(0.061 ± 0.004)

Reel Outside Diameter D 330

(12.992)

Reel Inner Diameter D1 50.0

(1.969) MIN.

Feed Hole Diameter D2 13.0 ± 0.20

(0.512 ± 0.008)

Sprocket Hole Position E 1.75 ± 0.10

(0.069 ± 0.004)

Punch Hole Position F 5.50 ± 0.05

(0.217 ± 0.002)

Punch Hole Pitch P 4.00 ± 0.10

(0.157 ± 0.004)

Sprocket Hole Pitch P0 4.00 ± 0.10

(0.157 ± 0.004)

Embossment Center P1 2.00 ± 0.05

(0.079 ± 0.002)

Overall Tape Thickness T 0.30 ± 0.10

(0.012 ± 0.004)

Tape Width W 12.00 ± 0.30

(0.472 ± 0.012)

Reel Width W118.4

(0.724) MAX.

Quantity per Reel -- 5,000

Legal Disclaimer Notice

This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and its

afliates (collectively, “Bourns”).

Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change

without notice. Users should check for and obtain the latest relevant information and verify that such information is current and

complete before placing orders for Bourns® products.

The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and

statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical

requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary

from the data sheet characteristics and parameters due to (i) the combination of the Bourns® product with other components

in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns®

product also can and do vary in different applications and actual performance may vary over time. Users should always verify

the actual performance of the Bourns® product in their specic devices and applications, and make their own independent

judgments regarding the amount of additional test margin to design into their device or application to compensate for

differences between laboratory and real world conditions.

Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry

standard (e.g., ISO/TS 16949) or a particular qualication (e.g., UL listed or recognized), Bourns is not responsible for any

failure of an individual Bourns® product to meet the requirements of such industry standard or particular qualication. Users of

Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to their

devices or applications.

Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining ap-

plications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or

environmental damage. Unless expressly and specically approved in writing by two authorized Bourns representatives on a

case-by-case basis, use of any Bourns® products in such unauthorized applications might not be safe and thus is at the user’s

sole risk. Life-critical applications include devices identied by the U.S. Food and Drug Administration as Class III devices and

generally equivalent classications outside of the United States.

Bourns expressly identies those Bourns® standard products that are suitable for use in automotive applications on such

products’ data sheets in the section entitled “Applications.” Unless expressly and specically approved in writing by two

authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive

application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns

expressly identies a sub-category of automotive application in the data sheet for its standard products (such as infotainment

or lighting), such identication means that Bourns has reviewed its standard product and has determined that if such Bourns®

standard product is considered for potential use in automotive applications, it should only be used in such sub-category of

automotive applications. Any reference to Bourns® standard product in the data sheet as compliant with the AEC-Q standard

or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application.

Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally

or any other generally equivalent governmental organization standard applicable to products designed or manufactured for

use in aircraft or space applications. Bourns expressly identies Bourns® standard products that are suitable for use in aircraft

or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specically

approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard

product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at the

user’s sole risk.

The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns and

the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns and the

user regarding the use and level of such testing, the above provisions applicable to Bourns® standard products shall also apply

to such Bourns® custom products.

Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the

design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use

Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions

apply to all uses and applications that violate national or international prohibitions, including embargos or international

regulations. Further, Bourns® products and Bourns technology and technical data may not under any circumstance be

exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without prior

authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible

to receive U.S. commodities, software, and technical data.

To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential,

incidental or indirect damages or lost revenues or lost prots, and (ii) any and all implied warranties, including implied warranties

of tness for particular purpose, non-infringement and merchantability.

For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplied Chinese

bilingual versions are available at:

Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies

PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf

C1753 05/17/18R