Freescale Semiconductor Data Sheet: Technical Data Document Number: MPC5604P Rev. 8, 07/2012 MPC5604P 144 LQFP 20 mm x 20 mm 100 LQFP 14 mm x 14 mm Qorivva MPC5604P Microcontroller Data Sheet * * * * * * * * Up to 64 MHz, single issue, 32-bit CPU core complex (e200z0h) -- Compliant with Power Architecture embedded category -- Variable Length Encoding (VLE) Memory organization -- Up to 512 KB on-chip code flash memory with ECC and erase/program controller -- Optional 64 (4 x 16) KB on-chip data flash memory with ECC for EEPROM emulation -- Up to 40 KB on-chip SRAM with ECC Fail safe protection -- Programmable watchdog timer -- Non-maskable interrupt -- Fault collection unit Nexus L2+ interface Interrupts -- 16-channel eDMA controller -- 16 priority level controller General purpose I/Os individually programmable as input, output or special function 2 general purpose eTimer units -- 6 timers each with up/down count capabilities -- 16-bit resolution, cascadable counters -- Quadrature decode with rotation direction flag -- Double buffer input capture and output compare Communications interfaces -- 2 LINFlex channels (LIN 2.1) -- 4 DSPI channels with automatic chip select generation -- 1 FlexCAN interface (2.0B Active) with 32 message objects -- * * * * * * 1 safety port based on FlexCAN with 32 message objects and up to 7.5 Mbit/s capability; usable as second CAN when not used as safety port -- 1 FlexRayTM module (V2.1) with selectable dual or single channel support, 32 message objects and up to 10 Mbit/s Two 10-bit analog-to-digital converters (ADC) -- 2 x 15 input channels, 4 channels shared between the two ADCs -- Conversion time < 1 s including sampling time at full precision -- Programmable Cross Triggering Unit (CTU) -- 4 analog watchdogs with interrupt capability On-chip CAN/UART bootstrap loader with Boot Assist Module (BAM) 1 FlexPWM unit -- 8 complementary or independent outputs with ADC synchronization signals -- Polarity control, reload unit -- Integrated configurable dead time unit and inverter fault input pins -- 16-bit resolution, up to 2 x fCPU -- Lockable configuration Clock generation -- 4-40 MHz main oscillator -- 16 MHz internal RC oscillator -- Software controlled FMPLL capable of speeds as fast as 64 MHz Voltage supply -- 3.3 V or 5 V supply for I/Os and ADC -- On-chip single supply voltage regulator with external ballast transistor Operating temperature ranges: -40 to 125 C or -40 to 105 C Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products. (c) Freescale, Inc., 2008-2012. All rights reserved. Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.1 Document overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.3 Device comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.4 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.5 Feature details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.5.1 High performance e200z0 core processor. . . . . .7 1.5.2 Crossbar switch (XBAR) . . . . . . . . . . . . . . . . . . .8 1.5.3 Enhanced direct memory access (eDMA) . . . . . .8 1.5.4 Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.5.5 Static random access memory (SRAM). . . . . . . .9 1.5.6 Interrupt controller (INTC) . . . . . . . . . . . . . . . . . .9 1.5.7 System status and configuration module (SSCM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.5.8 System clocks and clock generation . . . . . . . . .10 1.5.9 Frequency-modulated phase-locked loop (FMPLL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.5.10 Main oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.5.11 Internal RC oscillator . . . . . . . . . . . . . . . . . . . . . 11 1.5.12 Periodic interrupt timer (PIT) . . . . . . . . . . . . . . . 11 1.5.13 System timer module (STM) . . . . . . . . . . . . . . . 11 1.5.14 Software watchdog timer (SWT) . . . . . . . . . . . . 11 1.5.15 Fault collection unit (FCU) . . . . . . . . . . . . . . . . .12 1.5.16 System integration unit - Lite (SIUL) . . . . . . . . .12 1.5.17 Boot and censorship . . . . . . . . . . . . . . . . . . . . .12 1.5.18 Error correction status module (ECSM). . . . . . .13 1.5.19 Peripheral bridge (PBRIDGE) . . . . . . . . . . . . . .13 1.5.20 Controller area network (FlexCAN) . . . . . . . . . .13 1.5.21 Safety port (FlexCAN) . . . . . . . . . . . . . . . . . . . .14 1.5.22 FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 1.5.23 Serial communication interface module (LINFlex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 1.5.24 Deserial serial peripheral interface (DSPI) . . . .15 1.5.25 Pulse width modulator (FlexPWM) . . . . . . . . . .16 1.5.26 eTimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 1.5.27 Analog-to-digital converter (ADC) module . . . . .17 1.5.28 Cross triggering unit (CTU) . . . . . . . . . . . . . . . .18 1.5.29 Nexus development interface (NDI). . . . . . . . . .18 1.5.30 Cyclic redundancy check (CRC) . . . . . . . . . . . .19 1.5.31 IEEE 1149.1 JTAG controller . . . . . . . . . . . . . . .19 1.5.32 On-chip voltage regulator (VREG). . . . . . . . . . .19 Package pinouts and signal descriptions . . . . . . . . . . . . . . . .20 2.1 Package pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 2.2.1 Power supply and reference voltage pins . . . . .21 2.2.2 System pins . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 2.2.3 Pin muxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Parameter classification . . . . . . . . . . . . . . . . . . . . . . . 3.3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . 3.4 Recommended operating conditions . . . . . . . . . . . . . . 3.5 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . 3.5.1 Package thermal characteristics . . . . . . . . . . . 3.5.2 General notes for specifications at maximum junction temperature . . . . . . . . . . . . . . . . . . . . 3.6 Electromagnetic interference (EMI) characteristics . . . 3.7 Electrostatic discharge (ESD) characteristics . . . . . . . 3.8 Power management electrical characteristics . . . . . . . 3.8.1 Voltage regulator electrical characteristics . . . . 3.8.2 Voltage monitor electrical characteristics . . . . . 3.9 Power up/down sequencing . . . . . . . . . . . . . . . . . . . . 3.10 DC electrical characteristics . . . . . . . . . . . . . . . . . . . . 3.10.1 NVUSRO register . . . . . . . . . . . . . . . . . . . . . . . 3.10.2 DC electrical characteristics (5 V) . . . . . . . . . . 3.10.3 DC electrical characteristics (3.3 V) . . . . . . . . . 3.10.4 Input DC electrical characteristics definition . . 3.10.5 I/O pad current specification. . . . . . . . . . . . . . . 3.11 Main oscillator electrical characteristics . . . . . . . . . . . 3.12 FMPLL electrical characteristics . . . . . . . . . . . . . . . . . 3.13 16 MHz RC oscillator electrical characteristics . . . . . . 3.14 Analog-to-digital converter (ADC) electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14.1 Input impedance and ADC accuracy . . . . . . . . 3.14.2 ADC conversion characteristics . . . . . . . . . . . . 3.15 Flash memory electrical characteristics. . . . . . . . . . . . 3.16 AC specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16.1 Pad AC specifications . . . . . . . . . . . . . . . . . . . 3.17 AC timing characteristics . . . . . . . . . . . . . . . . . . . . . . . 3.17.1 RESET pin characteristics . . . . . . . . . . . . . . . . 3.17.2 IEEE 1149.1 interface timing . . . . . . . . . . . . . . 3.17.3 Nexus timing . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17.4 External interrupt timing (IRQ pin) . . . . . . . . . . 3.17.5 DSPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . 4.1.1 144 LQFP mechanical outline drawing . . . . . . 4.1.2 100 LQFP mechanical outline drawing . . . . . . 5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix AAbbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 24 38 38 38 39 42 46 46 47 48 48 49 49 52 53 55 55 55 57 58 59 64 65 67 67 68 72 74 75 75 76 76 78 81 83 84 90 90 90 92 96 97 98 MPC5604P Microcontroller Data Sheet, Rev. 8 2 Freescale 1 Introduction 1.1 Document overview This document provides electrical specifications, pin assignments, and package diagrams for the MPC5603P/4P series of microcontroller units (MCUs). It also describes the device features and highlights important electrical and physical characteristics. For functional characteristics, refer to the device reference manual. 1.2 Description This 32-bit system-on-chip (SoC) automotive microcontroller family is the latest achievement in integrated automotive application controllers. It belongs to an expanding range of automotive-focused products designed to address chassis applications--specifically, electrical hydraulic power steering (EHPS) and electric power steering (EPS)--as well as airbag applications. This family is one of a series of next-generation integrated automotive microcontrollers based on the Power Architecture technology. The advanced and cost-efficient host processor core of this automotive controller family complies with the Power Architecture embedded category. It operates at speeds of up to 64 MHz and offers high performance processing optimized for low power consumption. It capitalizes on the available development infrastructure of current Power Architecture devices and is supported with software drivers, operating systems and configuration code to assist with users implementations. 1.3 Device comparison Table 1 provides a summary of different members of the MPC5604P family and their features to enable a comparison among the family members and an understanding of the range of functionality offered within this family. Table 1. MPC5604P device comparison Feature Code flash memory (with ECC) MPC5603P MPC5604P 384 KB 512 KB Data flash memory / EE option (with ECC) SRAM (with ECC) 64 KB (optional feature) 36 KB 40 KB Processor core 32-bit e200z0h Instruction set VLE (variable length encoding) CPU performance 0-64 MHz FMPLL (frequency-modulated phase-locked loop) module INTC (interrupt controller) channels PIT (periodic interrupt timer) 1 16 Optional feature FlexCAN (controller area network) Safety port 147 1 (includes four 32-bit timers) eDMA (enhanced direct memory access) channels FlexRay 2 22,3 Yes (via second FlexCAN module) FCU (fault collection unit) Yes CTU (cross triggering unit) Yes MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 3 Table 1. MPC5604P device comparison (continued) Feature MPC5603P eTimer MPC5604P 2 (16-bit, 6 channels) FlexPWM (pulse-width modulation) channels 8 (capturing on X-channels) 2 (10-bit, 15-channel4) ADC (analog-to-digital converter) LINFlex 2 DSPI (deserial serial peripheral interface) 4 CRC (cyclic redundancy check) unit Yes JTAG controller Yes Nexus port controller (NPC) Supply Yes (Level 2+) Digital power supply 3.3 V or 5 V single supply with external transistor Analog power supply 3.3 V or 5 V Internal RC oscillator 16 MHz External crystal oscillator Packages Temperature 4-40 MHz 100 LQFP 144 LQFP Standard ambient temperature -40 to 125 C 1 32 message buffers, selectable single or dual channel support Each FlexCAN module has 32 message buffers. 3 One FlexCAN module can act as a Safety Port with a bit rate as high as 7.5 Mbit/s. 4 Four channels shared between the two ADCs 2 1.4 Block diagram Figure 1 shows a top-level block diagram of the MPC5604P MCU. MPC5604P Microcontroller Data Sheet, Rev. 8 4 Freescale External ballast e200z0 Core 1.2 V regulator control 32-bit general purpose registers XOSC Integer execution unit 16 MHz RC oscillator FMPLL_0 (System) Special purpose registers Exception handler Instruction unit Variable length encoded instructions Branch prediction unit Load/store unit FMPLL_1 (FlexRay, MotCtrl) JTAG Nexus port controller Interrupt controller Nexus 2+ eDMA 16 channels Instruction 32-bit Master FlexRay Data 32-bit Master Master Crossbar switch (XBAR, AMBA 2.0 v6 AHB) ECSM SIUL BAM MC_ME MC_CGM MC_RGM SWT STM SRAM (with ECC) CRC Data Flash (with ECC) WKPU Code Flash (with ECC) Slave PIT Slave Slave FCU Safety port FlexCAN 2x LINFlex 4x DSPI 2x eTimer (6 ch) SSCM Channels 0-10 10-bit ADC_1 Shared channels 11-14 10-bit ADC_0 Channels 0-10 1.2 V Rail VREG CTU FlexPWM Peripheral bridge Legend: ADC BAM CRC CTU DSPI ECSM eDMA eTimer FCU Flash FlexCAN FlexPWM FMPLL INTC JTAG Analog-to-digital converter Boot assist module Cyclic redundancy check Cross triggering unit Deserial serial peripheral interface Error correction status module Enhanced direct memory access Enhanced timer Fault collection unit Flash memory Controller area network Flexible pulse width modulation Frequency-modulated phase-locked loop Interrupt controller JTAG controller LINFlex MC_CGM MC_ME MC_PCU MC_RGM PIT SIUL SRAM SSCM STM SWT WKPU XOSC XBAR Serial communication interface (LIN support) Clock generation module Mode entry module Power control unit Reset generation module Periodic interrupt timer System integration unit Lite Static random-access memory System status and configuration module System timer module Software watchdog timer Wakeup unit External oscillator Crossbar switch Figure 1. MPC5604P block diagram MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 5 Table 2. MPC5604P series block summary Block Function Analog-to-digital converter (ADC) Multi-channel, 10-bit analog-to-digital converter Boot assist module (BAM) Block of read-only memory containing VLE code which is executed according to the boot mode of the device Clock generation module (MC_CGM) Provides logic and control required for the generation of system and peripheral clocks Controller area network (FlexCAN) Supports the standard CAN communications protocol Cross triggering unit (CTU) Enables synchronization of ADC conversions with a timer event from the eMIOS or from the PIT Crossbar switch (XBAR) Supports simultaneous connections between two master ports and three slave ports; supports a 32-bit address bus width and a 32-bit data bus width Cyclic redundancy check (CRC) CRC checksum generator Deserial serial peripheral interface Provides a synchronous serial interface for communication with external devices (DSPI) Enhanced direct memory access (eDMA) Performs complex data transfers with minimal intervention from a host processor via "n" programmable channels Enhanced timer (eTimer) Provides enhanced programmable up/down modulo counting Error correction status module (ECSM) Provides a myriad of miscellaneous control functions for the device including program-visible information about configuration and revision levels, a reset status register, wakeup control for exiting sleep modes, and optional features such as information on memory errors reported by error-correcting codes External oscillator (XOSC) Provides an output clock used as input reference for FMPLL_0 or as reference clock for specific modules depending on system needs Fault collection unit (FCU) Provides functional safety to the device Flash memory Provides non-volatile storage for program code, constants and variables Frequency-modulated phase-locked loop (FMPLL) Generates high-speed system clocks and supports programmable frequency modulation Interrupt controller (INTC) Provides priority-based preemptive scheduling of interrupt requests JTAG controller Provides the means to test chip functionality and connectivity while remaining transparent to system logic when not in test mode LINFlex controller Manages a high number of LIN (Local Interconnect Network protocol) messages efficiently with minimum load on CPU Mode entry module (MC_ME) Provides a mechanism for controlling the device operational mode and mode transition sequences in all functional states; also manages the power control unit, reset generation module and clock generation module, and holds the configuration, control and status registers accessible for applications Periodic interrupt timer (PIT) Produces periodic interrupts and triggers Peripheral bridge (PBRIDGE) Interface between the system bus and on-chip peripherals Power control unit (MC_PCU) Reduces the overall power consumption by disconnecting parts of the device from the power supply via a power switching device; device components are grouped into sections called "power domains" which are controlled by the PCU MPC5604P Microcontroller Data Sheet, Rev. 8 6 Freescale Table 2. MPC5604P series block summary (continued) Block Function Pulse width modulator (FlexPWM) Contains four PWM submodules, each of which is capable of controlling a single half-bridge power stage and two fault input channels Reset generation module (MC_RGM) Centralizes reset sources and manages the device reset sequence of the device Static random-access memory (SRAM) Provides storage for program code, constants, and variables System integration unit lite (SIUL) Provides control over all the electrical pad controls and up 32 ports with 16 bits of bidirectional, general-purpose input and output signals and supports up to 32 external interrupts with trigger event configuration System status and configuration module (SSCM) Provides system configuration and status data (such as memory size and status, device mode and security status), device identification data, debug status port enable and selection, and bus and peripheral abort enable/disable System timer module (STM) Provides a set of output compare events to support AUTOSAR1 and operating system tasks System watchdog timer (SWT) Provides protection from runaway code Wakeup unit (WKPU) Supports up to 18 external sources that can generate interrupts or wakeup events, 1 of which can cause non-maskable interrupt requests or wakeup events 1 AUTOSAR: AUTomotive Open System ARchitecture (see http://www.autosar.org) 1.5 Feature details 1.5.1 High performance e200z0 core processor The e200z0 Power Architecture core provides the following features: * * * * * * * * * * * * * High performance e200z0 core processor for managing peripherals and interrupts Single issue 4-stage pipeline in-order execution 32-bit Power Architecture CPU Harvard architecture Variable length encoding (VLE), allowing mixed 16-bit and 32-bit instructions -- Results in smaller code size footprint -- Minimizes impact on performance Branch processing acceleration using lookahead instruction buffer Load/store unit -- 1 cycle load latency -- Misaligned access support -- No load-to-use pipeline bubbles Thirty-two 32-bit general purpose registers (GPRs) Separate instruction bus and load/store bus Harvard architecture Hardware vectored interrupt support Reservation instructions for implementing read-modify-write constructs Long cycle time instructions, except for guarded loads, do not increase interrupt latency Extensive system development support through Nexus debug port Non-maskable interrupt support MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 7 1.5.2 Crossbar switch (XBAR) The XBAR multi-port crossbar switch supports simultaneous connections between four master ports and three slave ports. The crossbar supports a 32-bit address bus width and a 32-bit data bus width. The crossbar allows for two concurrent transactions to occur from any master port to any slave port; but one of those transfers must be an instruction fetch from internal flash memory. If a slave port is simultaneously requested by more than one master port, arbitration logic will select the higher priority master and grant it ownership of the slave port. All other masters requesting that slave port will be stalled until the higher priority master completes its transactions. Requesting masters will be treated with equal priority and will be granted access to a slave port in round-robin fashion, based upon the ID of the last master to be granted access. The crossbar provides the following features: * * * * * 1.5.3 4 master ports: -- e200z0 core complex Instruction port -- e200z0 core complex Load/Store Data port -- eDMA -- FlexRay 3 slave ports: -- Flash memory (code flash and data flash) -- SRAM -- Peripheral bridge 32-bit internal address, 32-bit internal data paths Fixed Priority Arbitration based on Port Master Temporary dynamic priority elevation of masters Enhanced direct memory access (eDMA) The enhanced direct memory access (eDMA) controller is a second-generation module capable of performing complex data movements via 16 programmable channels, with minimal intervention from the host processor. The hardware micro architecture includes a DMA engine which performs source and destination address calculations, and the actual data movement operations, along with an SRAM-based memory containing the transfer control descriptors (TCD) for the channels. This implementation is utilized to minimize the overall block size. The eDMA module provides the following features: * * * * * * * * 1.5.4 16 channels support independent 8, 16 or 32-bit single value or block transfers Supports variable sized queues and circular queues Source and destination address registers are independently configured to either post-increment or to remain constant Each transfer is initiated by a peripheral, CPU, or eDMA channel request Each eDMA channel can optionally send an interrupt request to the CPU on completion of a single value or block transfer DMA transfers possible between system memories, DSPIs, ADC, FlexPWM, eTimer and CTU Programmable DMA channel multiplexer for assignment of any DMA source to any available DMA channel with as many as 30 request sources eDMA abort operation through software Flash memory The MPC5604P provides as much as 576 KB of programmable, non-volatile, flash memory. The non-volatile memory (NVM) can be used for instruction and/or data storage. The flash memory module interfaces the system bus to a dedicated flash memory MPC5604P Microcontroller Data Sheet, Rev. 8 8 Freescale array controller. It supports a 32-bit data bus width at the system bus port, and a 128-bit read data interface to flash memory. The module contains four 128-bit wide prefetch buffers. Prefetch buffer hits allow no-wait responses. Normal flash memory array accesses are registered and are forwarded to the system bus on the following cycle, incurring two wait-states. The flash memory module provides the following features: * * * * * * * * * * * * * * * As much as 576 KB flash memory -- 8 blocks (32 KB + 2x16 KB + 32 KB + 32 KB + 3x128 KB) code flash -- 4 blocks (16 KB + 16 KB + 16 KB + 16 KB) data flash -- Full Read While Write (RWW) capability between code and data flash Four 128-bit wide prefetch buffers to provide single cycle in-line accesses (prefetch buffers can be configured to prefetch code or data or both) Typical flash memory access time: 0 wait states for buffer hits, 2 wait states for page buffer miss at 64 MHz Hardware managed flash memory writes handled by 32-bit RISC Krypton engine Hardware and software configurable read and write access protections on a per-master basis Configurable access timing allowing use in a wide range of system frequencies Multiple-mapping support and mapping-based block access timing (up to 31 additional cycles) allowing use for emulation of other memory types. Software programmable block program/erase restriction control Erase of selected block(s) Read page sizes -- Code flash memory: 128 bits (4 words) -- Data flash memory: 32 bits (1 word) ECC with single-bit correction, double-bit detection for data integrity -- Code flash memory: 64-bit ECC -- Data flash memory: 64-bit ECC Embedded hardware program and erase algorithm Erase suspend, program suspend and erase-suspended program Censorship protection scheme to prevent flash memory content visibility Hardware support for EEPROM emulation 1.5.5 Static random access memory (SRAM) The MPC5604P SRAM module provides up to 40 KB of general-purpose memory. ECC handling is done on a 32-bit boundary and is completely software compatible with MPC55xx family devices with an e200z6 core and 64-bit wide ECC. The SRAM module provides the following features: * * * * Supports read/write accesses mapped to the SRAM from any master Up to 40 KB general purpose SRAM Supports byte (8-bit), half word (16-bit), and word (32-bit) writes for optimal use of memory Typical SRAM access time: 0 wait-state for reads and 32-bit writes; 1 wait state for 8- and 16-bit writes if back to back with a read to same memory block 1.5.6 Interrupt controller (INTC) The interrupt controller (INTC) provides priority-based preemptive scheduling of interrupt requests, suitable for statically scheduled hard real-time systems. The INTC handles 147 selectable-priority interrupt sources. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 9 For high priority interrupt requests, the time from the assertion of the interrupt request from the peripheral to when the processor is executing the interrupt service routine (ISR) has been minimized. The INTC provides a unique vector for each interrupt request source for quick determination of which ISR has to be executed. It also provides a wide number of priorities so that lower priority ISRs do not delay the execution of higher priority ISRs. To allow the appropriate priorities for each source of interrupt request, the priority of each interrupt request is software configurable. When multiple tasks share a resource, coherent accesses to that resource need to be supported. The INTC supports the priority ceiling protocol (PCP) for coherent accesses. By providing a modifiable priority mask, the priority can be raised temporarily so that all tasks which share the same resource can not preempt each other. The INTC provides the following features: * * * * * 1.5.7 Unique 9-bit vector for each separate interrupt source 8 software triggerable interrupt sources 16 priority levels with fixed hardware arbitration within priority levels for each interrupt source Ability to modify the ISR or task priority: modifying the priority can be used to implement the Priority Ceiling Protocol for accessing shared resources. 2 external high priority interrupts directly accessing the main core and I/O processor (IOP) critical interrupt mechanism System status and configuration module (SSCM) The system status and configuration module (SSCM) provides central device functionality. The SSCM includes these features: * * * 1.5.8 System configuration and status -- Memory sizes/status -- Device mode and security status -- Determine boot vector -- Search code flash for bootable sector -- DMA status Debug status port enable and selection Bus and peripheral abort enable/disable System clocks and clock generation The following list summarizes the system clock and clock generation on the MPC5604P: * * * * * * 1.5.9 Lock detect circuitry continuously monitors lock status Loss of clock (LOC) detection for PLL outputs Programmable output clock divider (1, 2, 4, 8) FlexPWM module and eTimer module can run on an independent clock source On-chip oscillator with automatic level control Internal 16 MHz RC oscillator for rapid start-up and safe mode: supports frequency trimming by user application Frequency-modulated phase-locked loop (FMPLL) The FMPLL allows the user to generate high speed system clocks from a 4-40 MHz input clock. Further, the FMPLL supports programmable frequency modulation of the system clock. The PLL multiplication factor, output clock divider ratio are all software configurable. The PLL has the following major features: * Input clock frequency: 4-40 MHz MPC5604P Microcontroller Data Sheet, Rev. 8 10 Freescale * * * * * * Maximum output frequency: 64 MHz Voltage controlled oscillator (VCO)--frequency 256-512 MHz Reduced frequency divider (RFD) for reduced frequency operation without forcing the PLL to relock Frequency-modulated PLL -- Modulation enabled/disabled through software -- Triangle wave modulation Programmable modulation depth (0.25% to 4% deviation from center frequency): programmable modulation frequency dependent on reference frequency Self-clocked mode (SCM) operation 1.5.10 Main oscillator The main oscillator provides these features: * * * Input frequency range: 4-40 MHz Crystal input mode or oscillator input mode PLL reference 1.5.11 Internal RC oscillator This device has an RC ladder phase-shift oscillator. The architecture uses constant current charging of a capacitor. The voltage at the capacitor is compared by the stable bandgap reference voltage. The RC oscillator provides these features: * * * * Nominal frequency 16 MHz 5% variation over voltage and temperature after process trim Clock output of the RC oscillator serves as system clock source in case loss of lock or loss of clock is detected by the PLL RC oscillator is used as the default system clock during startup 1.5.12 Periodic interrupt timer (PIT) The PIT module implements these features: * * * * 4 general purpose interrupt timers 32-bit counter resolution Clocked by system clock frequency Each channel can be used as trigger for a DMA request 1.5.13 System timer module (STM) The STM module implements these features: * * * * One 32-bit up counter with 8-bit prescaler Four 32-bit compare channels Independent interrupt source for each channel Counter can be stopped in debug mode 1.5.14 Software watchdog timer (SWT) The SWT has the following features: MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 11 * * * * * * * 32-bit time-out register to set the time-out period Programmable selection of system or oscillator clock for timer operation Programmable selection of window mode or regular servicing Programmable selection of reset or interrupt on an initial time-out Master access protection Hard and soft configuration lock bits Reset configuration inputs allow timer to be enabled out of reset 1.5.15 Fault collection unit (FCU) The FCU provides an independent fault reporting mechanism even if the CPU is malfunctioning. The FCU module has the following features: * * * * * FCU status register reporting the device status Continuous monitoring of critical fault signals User selection of critical signals from different fault sources inside the device Critical fault events trigger 2 external pins (user selected signal protocol) that can be used externally to reset the device and/or other circuitry (for example, safety relay or FlexRay transceiver) Faults are latched into a register 1.5.16 System integration unit - Lite (SIUL) The MPC5604P SIUL controls MCU pad configuration, external interrupt, general purpose I/O (GPIO), and internal peripheral multiplexing. The pad configuration block controls the static electrical characteristics of I/O pins. The GPIO block provides uniform and discrete input/output control of the I/O pins of the MCU. The SIU provides the following features: * * * * * * * Centralized general purpose input output (GPIO) control of as many as 80 input/output pins and 26 analog input-only pads (package dependent) All GPIO pins can be independently configured to support pull-up, pull down, or no pull Reading and writing to GPIO supported both as individual pins and 16-bit wide ports All peripheral pins (except ADC channels) can be alternatively configured as both general purpose input or output pins ADC channels support alternative configuration as general purpose inputs Direct readback of the pin value is supported on all pins through the SIUL Configurable digital input filter that can be applied to some general purpose input pins for noise elimination: as many as 4 internal functions can be multiplexed onto 1 pin 1.5.17 Boot and censorship Different booting modes are available in the MPC5604P: booting from internal flash memory and booting via a serial link. The default booting scheme uses the internal flash memory (an internal pull-down is used to select this mode). Optionally, the user can boot via FlexCAN or LINFlex (using the boot assist module software). A censorship scheme is provided to protect the content of the flash memory and offer increased security for the entire device. A password mechanism is designed to grant the legitimate user access to the non-volatile memory. MPC5604P Microcontroller Data Sheet, Rev. 8 12 Freescale 1.5.17.1 Boot assist module (BAM) The BAM is a block of read-only one-time programmed memory and is identical for all MPC560xP devices that are based on the e200z0h core. The BAM program is executed every time the device is powered on if the alternate boot mode has been selected by the user. The BAM provides the following features: * * Serial bootloading via FlexCAN or LINFlex Ability to accept a password via the used serial communication channel to grant the legitimate user access to the non-volatile memory 1.5.18 Error correction status module (ECSM) The ECSM provides a myriad of miscellaneous control functions regarding program-visible information about the platform configuration and revision levels, a reset status register, a software watchdog timer, wakeup control for exiting sleep modes, and information on platform memory errors reported by error-correcting codes and/or generic access error information for certain processor cores. The Error Correction Status Module supports a number of miscellaneous control functions for the platform. The ECSM includes these features: * * Registers for capturing information on platform memory errors if error-correcting codes (ECC) are implemented For test purposes, optional registers to specify the generation of double-bit memory errors are enabled on the MPC5604P. The sources of the ECC errors are: * * Flash memory SRAM 1.5.19 Peripheral bridge (PBRIDGE) The PBRIDGE implements the following features: * * * * * Duplicated periphery Master access privilege level per peripheral (per master: read access enable; write access enable) Write buffering for peripherals Checker applied on PBRIDGE output toward periphery Byte endianess swap capability 1.5.20 Controller area network (FlexCAN) The MPC5604P MCU contains one controller area network (FlexCAN) module. This module is a communication controller implementing the CAN protocol according to Bosch Specification version 2.0B. The CAN protocol was designed to be used primarily as a vehicle serial data bus, meeting the specific requirements of this field: real-time processing, reliable operation in the EMI environment of a vehicle, cost-effectiveness and required bandwidth. The FlexCAN module contains 32 message buffers. The FlexCAN module provides the following features: * Full implementation of the CAN protocol specification, version 2.0B -- Standard data and remote frames -- Extended data and remote frames -- Up to 8-bytes data length -- Programmable bit rate up to 1 Mbit/s MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 13 * * * * * * * * * * * * * * 32 message buffers of up to 8-bytes data length Each message buffer configurable as Rx or Tx, all supporting standard and extended messages Programmable loop-back mode supporting self-test operation 3 programmable mask registers Programmable transmit-first scheme: lowest ID or lowest buffer number Time stamp based on 16-bit free-running timer Global network time, synchronized by a specific message Maskable interrupts Independent of the transmission medium (an external transceiver is assumed) High immunity to EMI Short latency time due to an arbitration scheme for high-priority messages Transmit features -- Supports configuration of multiple mailboxes to form message queues of scalable depth -- Arbitration scheme according to message ID or message buffer number -- Internal arbitration to guarantee no inner or outer priority inversion -- Transmit abort procedure and notification Receive features -- Individual programmable filters for each mailbox -- 8 mailboxes configurable as a six-entry receive FIFO -- 8 programmable acceptance filters for receive FIFO Programmable clock source -- System clock -- Direct oscillator clock to avoid PLL jitter 1.5.21 Safety port (FlexCAN) The MPC5604P MCU has a second CAN controller synthesized to run at high bit rates to be used as a safety port. The CAN module of the safety port provides the following features: * * * * Identical to the FlexCAN module Bit rate as fast as 7.5 Mbit/s at 60 MHz CPU clock using direct connection between CAN modules (no physical transceiver required) 32 message buffers of up to 8 bytes data length Can be used as a second independent CAN module 1.5.22 FlexRay The FlexRay module provides the following features: * * * * * * * Full implementation of FlexRay Protocol Specification 2.1 32 configurable message buffers can be handled Dual channel or single channel mode of operation, each as fast as 10 Mbit/s data rate Message buffers configurable as Tx, Rx or RxFIFO Message buffer size configurable Message filtering for all message buffers based on FrameID, cycle count and message ID Programmable acceptance filters for RxFIFO message buffers MPC5604P Microcontroller Data Sheet, Rev. 8 14 Freescale 1.5.23 Serial communication interface module (LINFlex) The LINFlex (local interconnect network flexible) on the MPC5604P features the following: * * * * * * Supports LIN Master mode, LIN Slave mode and UART mode LIN state machine compliant to LIN1.3, 2.0, and 2.1 specifications Handles LIN frame transmission and reception without CPU intervention LIN features -- Autonomous LIN frame handling -- Message buffer to store Identifier and as much as 8 data bytes -- Supports message length as long as 64 bytes -- Detection and flagging of LIN errors (sync field, delimiter, ID parity, bit framing, checksum, and time-out) -- Classic or extended checksum calculation -- Configurable Break duration as long as 36-bit times -- Programmable baud rate prescalers (13-bit mantissa, 4-bit fractional) -- Diagnostic features: Loop back; Self Test; LIN bus stuck dominant detection -- Interrupt-driven operation with 16 interrupt sources LIN slave mode features -- Autonomous LIN header handling -- Autonomous LIN response handling UART mode -- Full-duplex operation -- Standard non return-to-zero (NRZ) mark/space format -- Data buffers with 4-byte receive, 4-byte transmit -- Configurable word length (8-bit or 9-bit words) -- Error detection and flagging -- Parity, Noise and Framing errors -- Interrupt-driven operation with four interrupt sources -- Separate transmitter and receiver CPU interrupt sources -- 16-bit programmable baud-rate modulus counter and 16-bit fractional -- 2 receiver wake-up methods 1.5.24 Deserial serial peripheral interface (DSPI) The deserial serial peripheral interface (DSPI) module provides a synchronous serial interface for communication between the MPC5604P MCU and external devices. The DSPI modules provide these features: * * * * * * * * Full duplex, synchronous transfers Master or slave operation Programmable master bit rates Programmable clock polarity and phase End-of-transmission interrupt flag Programmable transfer baud rate Programmable data frames from 4 to 16 bits Up to 20 chip select lines available -- 8 on DSPI_0 -- 4 each on DSPI_1, DSPI_2 and DSPI_3 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 15 * * * * * 8 clock and transfer attributes registers Chip select strobe available as alternate function on one of the chip select pins for deglitching FIFOs for buffering as many as 5 transfers on the transmit and receive side Queueing operation possible through use of the eDMA General purpose I/O functionality on pins when not used for SPI 1.5.25 Pulse width modulator (FlexPWM) The pulse width modulator module (PWM) contains four PWM submodules, each capable of controlling a single half-bridge power stage. There are also four fault channels. This PWM is capable of controlling most motor types: AC induction motors (ACIM), permanent magnet AC motors (PMAC), both brushless (BLDC) and brush DC motors (BDC), switched (SRM) and variable reluctance motors (VRM), and stepper motors. The FlexPWM block implements the following features: * * * * * * * * * * * * * * * * * * * * * * * 16-bit resolution for center, edge-aligned, and asymmetrical PWMs Maximum operating clock frequency of 120 MHz PWM outputs can operate as complementary pairs or independent channels Can accept signed numbers for PWM generation Independent control of both edges of each PWM output Synchronization to external hardware or other PWM supported Double buffered PWM registers -- Integral reload rates from 1 to 16 -- Half cycle reload capability Multiple ADC trigger events can be generated per PWM cycle via hardware Write protection for critical registers Fault inputs can be assigned to control multiple PWM outputs Programmable filters for fault inputs Independently programmable PWM output polarity Independent top and bottom deadtime insertion Each complementary pair can operate with its own PWM frequency and deadtime values Individual software-control for each PWM output All outputs can be programmed to change simultaneously via a "Force Out" event PWMX pin can optionally output a third PWM signal from each submodule Channels not used for PWM generation can be used for buffered output compare functions Channels not used for PWM generation can be used for input capture functions Enhanced dual-edge capture functionality eDMA support with automatic reload 2 fault inputs Capture capability for PWMA, PWMB, and PWMX channels not supported 1.5.26 eTimer The MPC5604P includes two eTimer modules. Each module provides six 16-bit general purpose up/down timer/counter units with the following features: * * Maximum operating clock frequency of 120 MHz Individual channel capability MPC5604P Microcontroller Data Sheet, Rev. 8 16 Freescale * * * * * * * -- Input capture trigger -- Output compare -- Double buffer (to capture rising edge and falling edge) -- Separate prescaler for each counter -- Selectable clock source -- 0-100% pulse measurement -- Rotation direction flag (Quad decoder mode) Maximum count rate -- External event counting: max. count rate = peripheral clock/2 -- Internal clock counting: max. count rate = peripheral clock Counters are: -- Cascadable -- Preloadable Programmable count modulo Quadrature decode capabilities Counters can share available input pins Count once or repeatedly Pins available as GPIO when timer functionality not in use 1.5.27 Analog-to-digital converter (ADC) module The ADC module provides the following features: Analog part: * 2 on-chip AD converters -- 10-bit AD resolution -- 1 sample and hold unit per ADC -- Conversion time, including sampling time, less than 1 s (at full precision) -- Typical sampling time is 150 ns min. (at full precision) -- Differential non-linearity error (DNL) 1 LSB -- Integral non-linearity error (INL) 1.5 LSB -- TUE <3 LSB -- Single-ended input signal up to 5.0 V -- The ADC and its reference can be supplied with a voltage independent from VDDIO -- The ADC supply can be equal or higher than VDDIO -- The ADC supply and the ADC reference are not independent from each other (they are internally bonded to the same pad) -- Sample times of 2 (default), 8, 64, or 128 ADC clock cycles Digital part: * * * * 2 x 13 input channels including 4 channels shared between the 2 converters 4 analog watchdogs comparing ADC results against predefined levels (low, high, range) before results are stored in the appropriate ADC result location, 2 modes of operation: Normal mode or CTU control mode Normal mode features -- Register-based interface with the CPU: control register, status register, 1 result register per channel MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 17 * -- ADC state machine managing 3 request flows: regular command, hardware injected command, software injected command -- Selectable priority between software and hardware injected commands -- 4 analog watchdogs comparing ADC results against predefined levels (low, high, range) -- DMA compatible interface CTU control mode features -- Triggered mode only -- 4 independent result queues (2 x 16 entries, 2 x 4 entries) -- Result alignment circuitry (left justified; right justified) -- 32-bit read mode allows to have channel ID on one of the 16-bit part -- DMA compatible interfaces 1.5.28 Cross triggering unit (CTU) The cross triggering unit allows automatic generation of ADC conversion requests on user selected conditions without CPU load during the PWM period and with minimized CPU load for dynamic configuration. It implements the following features: * * * * * * * * Double buffered trigger generation unit with as many as eight independent triggers generated from external triggers Trigger generation unit configurable in sequential mode or in triggered mode Each Trigger can be appropriately delayed to compensate the delay of external low pass filter Double buffered global trigger unit allowing eTimer synchronization and/or ADC command generation Double buffered ADC command list pointers to minimize ADC-trigger unit update Double buffered ADC conversion command list with as many as 24 ADC commands Each trigger has the capability to generate consecutive commands ADC conversion command allows to control ADC channel from each ADC, single or synchronous sampling, independent result queue selection 1.5.29 Nexus development interface (NDI) The NDI (Nexus Development Interface) block provides real-time development support capabilities for the MPC5604P Power Architecture based MCU in compliance with the IEEE-ISTO 5001-2003 standard. This development support is supplied for MCUs without requiring external address and data pins for internal visibility. The NDI block is an integration of several individual Nexus blocks that are selected to provide the development support interface for this device. The NDI block interfaces to the host processor and internal busses to provide development support as per the IEEE-ISTO 5001-2003 Class 2+ standard. The development support provided includes access to the MCU's internal memory map and access to the processor's internal registers during run time. The Nexus Interface provides the following features: * * * Configured via the IEEE 1149.1 All Nexus port pins operate at VDDIO (no dedicated power supply) Nexus 2+ features supported -- Static debug -- Watchpoint messaging -- Ownership trace messaging -- Program trace messaging -- Real time read/write of any internally memory mapped resources through JTAG pins -- Overrun control, which selects whether to stall before Nexus overruns or keep executing and allow overwrite of information MPC5604P Microcontroller Data Sheet, Rev. 8 18 Freescale * * -- Watchpoint triggering, watchpoint triggers program tracing Auxiliary Output Port -- 4 MDO (Message Data Out) pins -- MCKO (Message Clock Out) pin -- 2 MSEO (Message Start/End Out) pins -- EVTO (Event Out) pin Auxiliary Input Port -- EVTI (Event In) pin 1.5.30 Cyclic redundancy check (CRC) The CRC computing unit is dedicated to the computation of CRC off-loading the CPU. The CRC module features: * * * Support for CRC-16-CCITT (x25 protocol): -- x16 + x12 + x5 + 1 Support for CRC-32 (Ethernet protocol): -- x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + x8 + x7 + x5 + x4 + x2 + x + 1 Zero wait states for each write/read operations to the CRC_CFG and CRC_INP registers at the maximum frequency 1.5.31 IEEE 1149.1 JTAG controller The JTAG controller (JTAGC) block provides the means to test chip functionality and connectivity while remaining transparent to system logic when not in test mode. All data input to and output from the JTAGC block is communicated in serial format. The JTAGC block is compliant with the IEEE standard. The JTAG controller provides the following features: * * * * * * IEEE Test Access Port (TAP) interface with 4 pins (TDI, TMS, TCK, TDO) Selectable modes of operation include JTAGC/debug or normal system operation. A 5-bit instruction register that supports the following IEEE 1149.1-2001 defined instructions: -- BYPASS, IDCODE, EXTEST, SAMPLE, SAMPLE/PRELOAD A 5-bit instruction register that supports the additional following public instructions: -- ACCESS_AUX_TAP_NPC, ACCESS_AUX_TAP_ONCE 3 test data registers: a bypass register, a boundary scan register, and a device identification register. A TAP controller state machine that controls the operation of the data registers, instruction register and associated circuitry. 1.5.32 On-chip voltage regulator (VREG) The on-chip voltage regulator module provides the following features: * * * Uses external NPN (negative-positive-negative) transistor Regulates external 3.3 V /5.0 V down to 1.2 V for the core logic Low voltage detection on the internal 1.2 V and I/O voltage 3.3 V MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 19 2 Package pinouts and signal descriptions 2.1 Package pinouts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 144 LQFP 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 A[4] VPP_TEST F[12] D[14] G[3] C[14] G[2] C[13] G[4] D[12] G[6] VDD_HV_FL VSS_HV_FL D[13] VSS_LV_COR1 VDD_LV_COR1 A[3] VDD_HV_IO2 VSS_HV_IO2 TDO TCK TMS TDI G[5] A[2] G[7] C[12] G[8] C[11] G[9] D[11] G[10] D[10] G[11] A[1] A[0] D[7] G[0] E[1] E[3] C[1] E[4] B[7] E[5] C[2] E[6] B[8] E[7] E[2] VDD_HV_ADC0 VSS_HV_ADC0 B[9] B[10] B[11] B[12] VDD_HV_ADC1 VSS_HV_ADC1 D[15] E[8] B[13] E[9] B[15] E[10] B[14] E[11] C[0] E[12] E[0] BCTRL VDD_LV_REGCOR VSS_LV_REGCOR VDD_HV_REG 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 NMI A[6] D[1] F[4] F[5] VDD_HV_IO0 VSS_HV_IO0 F[6] MDO[0] A[7] C[4] A[8] C[5] A[5] C[7] C[3] VSS_LV_COR0 VDD_LV_COR0 F[7] F[8] VDD_HV_IO1 VSS_HV_IO1 F[9] F[10] F[11] D[9] VDD_HV_OSC VSS_HV_OSC XTAL EXTAL RESET D[8] D[5] D[6] VSS_LV_COR3 VDD_LV_COR3 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 A[15] A[14] C[6] G[1] D[2] F[3] B[6] F[2] A[13] F[1] A[9] F[0] VSS_LV_COR2 VDD_LV_COR2 C[8] D[4] D[3] VSS_HV_IO3 VDD_HV_IO3 D[0] C[15] C[9] A[12] E[15] A[11] E[14] A[10] E[13] B[3] F[14] B[2] F[15] F[13] C[10] B[1] B[0] The LQFP pinouts are shown in the following figures. Note: Availability of port pin alternate functions depends on product selection. Figure 2. 144-pin LQFP pinout (top view) MPC5604P Microcontroller Data Sheet, Rev. 8 20 Freescale A[15] A[14] C[6] D[2] B[6] A[13] A[9] VSS_LV_COR2 VDD_LV_COR2 C[8] D[4] D[3] VSS_HV_IO3 VDD_HV_IO3 D[0] C[15] C[9] A[12] A[11] A[10] B[3] B[2] C[10] B[1] B[0] 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 100 LQFP 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A[4] VPP_TEST D[14] C[14] C[13] D[12] VDD_HV_FL VSS_HV_FL D[13] VSS_LV_COR1 VDD_LV_COR1 A[3] VDD_HV_IO2 VSS_HV_IO2 TDO TCK TMS TDI A[2] C[12] C[11] D[11] D[10] A[1] A[0] D[7] E[1] C[1] B[7] C[2] B[8] E[2] VDD_HV_ADC0 VSS_HV_ADC0 B[9] B[10] B[11] B[12] VDD_HV_ADC1 VSS_HV_ADC1 D[15] B[13] B[15] B[14] C[0] E[0] BCTRL VDD_LV_REGCOR VSS_LV_REGCOR VDD_HV_REG 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NMI A[6] D[1] A[7] C[4] A[8] C[5] A[5] C[7] C[3] VSS_LV_COR0 VDD_LV_COR0 VDD_HV_IO1 VSS_HV_IO1 D[9] VDD_HV_OSC VSS_HV_OSC XTAL EXTAL RESET D[8] D[5] D[6] VSS_LV_COR3 VDD_LV_COR3 Note: Availability of port pin alternate functions depends on product selection. Figure 3. 100-pin LQFP pinout (top view) 2.2 Pin description The following sections provide signal descriptions and related information about the functionality and configuration of the MPC5604P devices. 2.2.1 Power supply and reference voltage pins Table 3 lists the power supply and reference voltage for the MPC5604P devices. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 21 Table 3. Supply pins Supply Symbol Pin Description 100-pin 144-pin VREG control and power supply pins. Pins available on 100-pin and 144-pin package. BCTRL Voltage regulator external NPN ballast base control pin 47 69 Voltage regulator supply voltage 50 72 VDD_LV_REGCOR 1.2 V decoupling pins for core logic and regulator feedback. Decoupling capacitor must be connected between this pins and VSS_LV_REGCOR. 48 70 VSS_LV_REGCOR 1.2 V decoupling pins for core logic and regulator feedback. Decoupling capacitor must be connected between this pins and VDD_LV_REGCOR. 49 71 VDD_HV_REG (3.3 V or 5.0 V) ADC_0/ADC_1 reference and supply voltage. Pins available on 100-pin and 144-pin package. VDD_HV_ADC01 ADC_0 supply and high reference voltage 33 50 VSS_HV_ADC0 ADC_0 ground and low reference voltage 34 51 VDD_HV_ADC1 ADC_1 supply and high reference voltage 39 56 VSS_HV_ADC1 ADC_1 ground and low reference voltage 40 57 Power supply pins (3.3 V or 5.0 V). All pins available on 144-pin package. Five pairs (VDD; VSS) available on 100-pin package. VDD_HV_IO02 Input/Output supply voltage -- 6 VSS_HV_IO02 Input/Output ground -- 7 VDD_HV_IO1 Input/Output supply voltage 13 21 VSS_HV_IO1 Input/Output ground 14 22 VDD_HV_IO2 Input/Output supply voltage 63 91 VSS_HV_IO2 Input/Output ground 62 90 VDD_HV_IO3 Input/Output supply voltage 87 126 VSS_HV_IO3 Input/Output ground 88 127 VDD_HV_FL Code and data flash supply voltage 69 97 VSS_HV_FL Code and data flash supply ground 68 96 VDD_HV_OSC Crystal oscillator amplifier supply voltage 16 27 VSS_HV_OSC Crystal oscillator amplifier ground 17 28 Power supply pins (1.2 V). All pins available on 100-pin and 144-pin package. VDD_LV_COR0 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VSS_LV_COR pin. 12 18 MPC5604P Microcontroller Data Sheet, Rev. 8 22 Freescale Table 3. Supply pins (continued) Supply Symbol Pin Description 100-pin 144-pin VSS_LV_COR0 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VDD_LV_COR pin. 11 17 VDD_LV_COR1 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VSS_LV_COR pin. 65 93 VSS_LV_COR1 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VDD_LV_COR pin. 66 94 VDD_LV_COR2 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VSS_LV_COR pin. 92 131 VSS_LV_COR2 1.2 V Decoupling pins for core logic. Decoupling capacitor must be connected between these pins and the nearest VDD_LV_COR pin. 93 132 VDD_LV_COR3 1.2 V Decoupling pins for on-chip PLL modules. Decoupling capacitor must be connected between this pin and VSS_LV_COR3. 25 36 VSS_LV_COR3 1.2 V Decoupling pins for on-chip PLL modules. Decoupling capacitor must be connected between this pin and VDD_LV_COR3. 24 35 1 Analog supply/ground and high/low reference lines are internally physically separate, but are shorted via a double-bonding connection on VDD_HV_ADCx/VSS_HV_ADCx pins. 2 Not available on 100-pin package. 2.2.2 System pins Table 3 and Table 4 contain information on pin functions for the MPC5604P devices. The pins listed in Table 4 are single-function pins. The pins shown in Table 5 are multi-function pins, programmable via their respective Pad Configuration Register (PCR) values. Table 4. System pins Pad speed1 Symbol Description Pin Direction SRC = 0 SRC = 1 100-pin 144-pin -- 9 Dedicated pins. Available on 100-pin and 144-pin package. MDO[0] Nexus Message Data Output--line 0 NMI Non-Maskable Interrupt XTAL Analog output of the oscillator amplifier circuit; needs to be grounded if oscillator is used in bypass mode Output only Fast Input only Slow -- 1 1 -- -- -- 18 29 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 23 Table 4. System pins (continued) Pad speed1 Symbol Description SRC = 0 SRC = 1 EXTAL * Analog input of oscillator amplifier circuit, when oscillator not in bypass mode * Analog input for clock generator when oscillator in bypass mode TMS JTAG state machine control TCK Pin Direction 100-pin 144-pin -- -- -- 19 30 Bidirectional Slow Fast 59 87 JTAG clock Input only Slow -- 60 88 TDI Test Data In Input only Slow Medium 58 86 TDO Test Data Out Output only Slow Fast 61 89 -- 20 31 -- 74 107 Reset pin, available on 100-pin and 144-pin package. RESET Bidirectional reset with Schmitt trigger characteristics and noise filter Bidirectional Medium Test pin, available on 100-pin and 144-pin package. VPP_TEST Pin for testing purpose only. To be tied to ground in normal operating mode. 1 2.2.3 -- -- SCR values refer to the value assigned to the Slew Rate Control bits of the pad configuration register. Pin muxing Table 5 defines the pin list and muxing for the MPC5604P devices. Each row of Table 5 shows all the possible ways of configuring each pin, via alternate functions. The default function assigned to each pin after reset is the ALT0 function. MPC5604P devices provide four main I/O pad types, depending on the associated functions: * * * * Slow pads are the most common, providing a compromise between transition time and low electromagnetic emission. Medium pads provide fast enough transition for serial communication channels with controlled current to reduce electromagnetic emission. Fast pads provide maximum speed. They are used for improved NEXUS debugging capability. Symmetric pads are designed to meet FlexRay requirements. Medium and Fast pads can use slow configuration to reduce electromagnetic emission, at the cost of reducing AC performance. For more information, see the data sheet's "Pad AC Specifications" section. MPC5604P Microcontroller Data Sheet, Rev. 8 24 Freescale Table 5. Pin muxing Pad speed5 Peripheral I/O direction4 Pin No. 144-pin Functions 3 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) A[0] PCR[0] ALT0 ALT1 ALT2 ALT3 -- GPIO[0] ETC[0] SCK F[0] EIRQ[0] SIUL eTimer_0 DSPI_2 FCU_0 SIUL I/O I/O O O I Slow Medium 51 73 A[1] PCR[1] ALT0 ALT1 ALT2 ALT3 -- GPIO[1] ETC[1] SOUT F[1] EIRQ[1] SIUL eTimer_0 DSPI_2 FCU_0 SIUL I/O I/O O O I Slow Medium 52 74 A[2]6 PCR[2] ALT0 ALT1 ALT2 ALT3 -- -- -- GPIO[2] ETC[2] -- A[3] SIN ABS[0] EIRQ[2] SIUL eTimer_0 -- FlexPWM_0 DSPI_2 MC_RGM SIUL I/O I/O -- O I I I Slow Medium 57 84 A[3]6 PCR[3] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[3] ETC[3] CS0 B[3] ABS[2] EIRQ[3] SIUL eTimer_0 DSPI_2 FlexPWM_0 MC_RGM SIUL I/O I/O I/O O I I Slow Medium 64 92 A[4]6 PCR[4] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[4] ETC[0] CS1 ETC[4] FAB EIRQ[4] SIUL eTimer_1 DSPI_2 eTimer_0 MC_RGM SIUL I/O I/O O I/O I I Slow Medium 75 108 A[5] PCR[5] ALT0 ALT1 ALT2 ALT3 -- GPIO[5] CS0 ETC[5] CS7 EIRQ[5] SIUL DSPI_1 eTimer_1 DSPI_0 SIUL I/O I/O I/O O I Slow Medium 8 14 A[6] PCR[6] ALT0 ALT1 ALT2 ALT3 -- GPIO[6] SCK -- -- EIRQ[6] SIUL DSPI_1 -- -- SIUL I/O I/O -- -- I Slow Medium 2 2 A[7] PCR[7] ALT0 ALT1 ALT2 ALT3 -- GPIO[7] SOUT -- -- EIRQ[7] SIUL DSPI_1 -- -- SIUL I/O O -- -- I Slow Medium 4 10 SRC = 0 SRC = 1 Port A (16-bit) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 25 Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) A[8] PCR[8] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[8] -- -- -- SIN EIRQ[8] SIUL -- -- -- DSPI_1 SIUL I/O -- -- -- I I Slow Medium 6 12 A[9] PCR[9] ALT0 ALT1 ALT2 ALT3 -- GPIO[9] CS1 -- B[3] FAULT[0] SIUL DSPI_2 -- FlexPWM_0 FlexPWM_0 I/O O -- O I Slow Medium 94 134 A[10] PCR[10] ALT0 ALT1 ALT2 ALT3 -- GPIO[10] CS0 B[0] X[2] EIRQ[9] SIUL DSPI_2 FlexPWM_0 FlexPWM_0 SIUL I/O I/O O I/O I Slow Medium 81 118 A[11] PCR[11] ALT0 ALT1 ALT2 ALT3 -- GPIO[11] SCK A[0] A[2] EIRQ[10] SIUL DSPI_2 FlexPWM_0 FlexPWM_0 SIUL I/O I/O O O I Slow Medium 82 120 A[12] PCR[12] ALT0 ALT1 ALT2 ALT3 -- GPIO[12] SOUT A[2] B[2] EIRQ[11] SIUL DSPI_2 FlexPWM_0 FlexPWM_0 SIUL I/O O O O I Slow Medium 83 122 A[13] PCR[13] ALT0 ALT1 ALT2 ALT3 -- -- -- GPIO[13] -- B[2] -- SIN FAULT[0] EIRQ[12] SIUL -- FlexPWM_0 -- DSPI_2 FlexPWM_0 SIUL I/O -- O -- I I I Slow Medium 95 136 A[14] PCR[14] ALT0 ALT1 ALT2 ALT3 -- GPIO[14] TXD ETC[4] -- EIRQ[13] SIUL Safety Port_0 eTimer_1 -- SIUL I/O O I/O -- I Slow Medium 99 143 A[15] PCR[15] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[15] -- ETC[5] -- RXD EIRQ[14] SIUL -- eTimer_1 -- Safety Port_0 SIUL I/O -- I/O -- I I Slow Medium 100 144 SRC = 0 SRC = 1 MPC5604P Microcontroller Data Sheet, Rev. 8 26 Freescale Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) B[0] PCR[16] ALT0 ALT1 ALT2 ALT3 -- GPIO[16] TXD ETC[2] DEBUG[0] EIRQ[15] SIUL FlexCAN_0 eTimer_1 SSCM SIUL I/O O I/O -- I Slow Medium 76 109 B[1] PCR[17] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[17] -- ETC[3] DEBUG[1] RXD EIRQ[16] SIUL -- eTimer_1 SSCM FlexCAN_0 SIUL I/O -- I/O -- I I Slow Medium 77 110 B[2] PCR[18] ALT0 ALT1 ALT2 ALT3 -- GPIO[18] TXD -- DEBUG[2] EIRQ[17] SIUL LIN_0 -- SSCM SIUL I/O O -- -- I Slow Medium 79 114 B[3] PCR[19] ALT0 ALT1 ALT2 ALT3 -- GPIO[19] -- -- DEBUG[3] RXD SIUL -- -- SSCM LIN_0 I/O -- -- -- I Slow Medium 80 116 B[6] PCR[22] ALT0 ALT1 ALT2 ALT3 -- GPIO[22] CLKOUT CS2 -- EIRQ[18] SIUL MC_CGL DSPI_2 -- SIUL I/O O O -- I Slow Medium 96 138 B[7] PCR[23] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[23] -- -- -- AN[0] RXD SIUL -- -- -- ADC_0 LIN_0 Input only -- -- 29 43 B[8] PCR[24] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[24] -- -- -- AN[1] ETC[5] SIUL -- -- -- ADC_0 eTimer_0 Input only -- -- 31 47 B[9] PCR[25] ALT0 ALT1 ALT2 ALT3 -- GPIO[25] -- -- -- AN[11] SIUL Input only -- -- -- ADC_0 / ADC_1 -- -- 35 52 SRC = 0 SRC = 1 Port B (16-bit) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 27 Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) B[10] PCR[26] ALT0 ALT1 ALT2 ALT3 -- GPIO[26] -- -- -- AN[12] SIUL Input only -- -- -- ADC_0 / ADC_1 -- -- 36 53 B[11] PCR[27] ALT0 ALT1 ALT2 ALT3 -- GPIO[27] -- -- -- AN[13] SIUL Input only -- -- -- ADC_0 / ADC_1 -- -- 37 54 B[12] PCR[28] ALT0 ALT1 ALT2 ALT3 -- GPIO[28] -- -- -- AN[14] SIUL Input only -- -- -- ADC_0 / ADC_1 -- -- 38 55 B[13] PCR[29] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[29] -- -- -- AN[0] RXD SIUL -- -- -- ADC_1 LIN_1 Input only -- -- 42 60 B[14] PCR[30] ALT0 ALT1 ALT2 ALT3 -- -- -- GPIO[30] -- -- -- AN[1] ETC[4] EIRQ[19] SIUL -- -- -- ADC_1 eTimer_0 SIUL Input only -- -- 44 64 B[15] PCR[31] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[31] -- -- -- AN[2] EIRQ[20] SIUL -- -- -- ADC_1 SIUL Input only -- -- 43 62 SRC = 0 SRC = 1 Port C (16-bit) C[0] PCR[32] ALT0 ALT1 ALT2 ALT3 -- GPIO[32] -- -- -- AN[3] SIUL -- -- -- ADC_1 Input only -- -- 45 66 C[1] PCR[33] ALT0 ALT1 ALT2 ALT3 -- GPIO[33] -- -- -- AN[2] SIUL -- -- -- ADC_0 Input only -- -- 28 41 MPC5604P Microcontroller Data Sheet, Rev. 8 28 Freescale Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) C[2] PCR[34] ALT0 ALT1 ALT2 ALT3 -- GPIO[34] -- -- -- AN[3] SIUL -- -- -- ADC_0 Input only -- -- 30 45 C[3] PCR[35] ALT0 ALT1 ALT2 ALT3 -- GPIO[35] CS1 ETC[4] TXD EIRQ[21] SIUL DSPI_0 eTimer_1 LIN_1 SIUL I/O O I/O O I Slow Medium 10 16 C[4] PCR[36] ALT0 ALT1 ALT2 ALT3 -- GPIO[36] CS0 X[1] DEBUG[4] EIRQ[22] SIUL DSPI_0 FlexPWM_0 SSCM SIUL I/O I/O I/O -- I Slow Medium 5 11 C[5] PCR[37] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[37] SCK -- DEBUG[5] FAULT[3] EIRQ[23] SIUL DSPI_0 -- SSCM FlexPWM_0 SIUL I/O I/O -- -- I I Slow Medium 7 13 C[6] PCR[38] ALT0 ALT1 ALT2 ALT3 -- GPIO[38] SOUT B[1] DEBUG[6] EIRQ[24] SIUL DSPI_0 FlexPWM_0 SSCM SIUL I/O I/O O -- I Slow Medium 98 142 C[7] PCR[39] ALT0 ALT1 ALT2 ALT3 -- GPIO[39] -- A[1] DEBUG[7] SIN SIUL -- FlexPWM_0 SSCM DSPI_0 I/O -- O -- I Slow Medium 9 15 C[8] PCR[40] ALT0 ALT1 ALT2 ALT3 -- GPIO[40] CS1 -- CS6 FAULT[2] SIUL DSPI_1 -- DSPI_0 FlexPWM_0 I/O O -- O I Slow Medium 91 130 C[9] PCR[41] ALT0 ALT1 ALT2 ALT3 -- GPIO[41] CS3 -- X[3] FAULT[2] SIUL DSPI_2 -- FlexPWM_0 FlexPWM_0 I/O O -- I/O I Slow Medium 84 123 C[10] PCR[42] ALT0 ALT1 ALT2 ALT3 -- GPIO[42] CS2 -- A[3] FAULT[1] SIUL DSPI_2 -- FlexPWM_0 FlexPWM_0 I/O O -- O I Slow Medium 78 111 SRC = 0 SRC = 1 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 29 Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) C[11] PCR[43] ALT0 ALT1 ALT2 ALT3 GPIO[43] ETC[4] CS2 CS0 SIUL eTimer_0 DSPI_2 DSPI_3 I/O I/O O I/O Slow Medium 55 80 C[12] PCR[44] ALT0 ALT1 ALT2 ALT3 GPIO[44] ETC[5] CS3 CS1 SIUL eTimer_0 DSPI_2 DSPI_3 I/O I/O O O Slow Medium 56 82 C[13] PCR[45] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[45] ETC[1] -- -- EXT_IN EXT_SYNC SIUL eTimer_1 -- -- CTU_0 FlexPWM_0 I/O I/O -- -- I I Slow Medium 71 101 C[14] PCR[46] ALT0 ALT1 ALT2 ALT3 GPIO[46] ETC[2] EXT_TGR -- SIUL eTimer_1 CTU_0 -- I/O I/O O -- Slow Medium 72 103 C[15] PCR[47] ALT0 ALT1 ALT2 ALT3 -- -- GPIO[47] CA_TR_EN ETC[0] A[1] EXT_IN EXT_SYNC SIUL FlexRay_0 eTimer_1 FlexPWM_0 CTU_0 FlexPWM_0 I/O O I/O O I I Slow Symmetric 85 124 SRC = 0 SRC = 1 Port D (16-bit) D[0] PCR[48] ALT0 ALT1 ALT2 ALT3 GPIO[48] CA_TX ETC[1] B[1] SIUL FlexRay_0 eTimer_1 FlexPWM_0 I/O O I/O O Slow Symmetric 86 125 D[1] PCR[49] ALT0 ALT1 ALT2 ALT3 -- GPIO[49] -- ETC[2] EXT_TRG CA_RX SIUL -- eTimer_1 CTU_0 FlexRay_0 I/O -- I/O O I Slow Medium 3 3 D[2] PCR[50] ALT0 ALT1 ALT2 ALT3 -- GPIO[50] -- ETC[3] X[3] CB_RX SIUL -- eTimer_1 FlexPWM_0 FlexRay_0 I/O -- I/O I/O I Slow Medium 97 140 D[3] PCR[51] ALT0 ALT1 ALT2 ALT3 GPIO[51] CB_TX ETC[4] A[3] SIUL FlexRay_0 eTimer_1 FlexPWM_0 I/O O I/O O Slow Symmetric 89 128 MPC5604P Microcontroller Data Sheet, Rev. 8 30 Freescale Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) D[4] PCR[52] ALT0 ALT1 ALT2 ALT3 GPIO[52] CB_TR_EN ETC[5] B[3] SIUL FlexRay_0 eTimer_1 FlexPWM_0 I/O O I/O O Slow Symmetric 90 129 D[5] PCR[53] ALT0 ALT1 ALT2 ALT3 GPIO[53] CS3 F[0] SOUT SIUL DSPI_0 FCU_0 DSPI_3 I/O O O O Slow Medium 22 33 D[6] PCR[54] ALT0 ALT1 ALT2 ALT3 -- GPIO[54] CS2 SCK -- FAULT[1] SIUL DSPI_0 DSPI_3 -- FlexPWM_0 I/O O I/O -- I Slow Medium 23 34 D[7] PCR[55] ALT0 ALT1 ALT2 ALT3 -- GPIO[55] CS3 F[1] CS4 SIN SIUL DSPI_1 FCU_0 DSPI_0 DSPI_3 I/O O O O I Slow Medium 26 37 D[8] PCR[56] ALT0 ALT1 ALT2 ALT3 -- GPIO[56] CS2 -- CS5 FAULT[3] SIUL DSPI_1 -- DSPI_0 FlexPWM_0 I/O O -- O I Slow Medium 21 32 D[9] PCR[57] ALT0 ALT1 ALT2 ALT3 GPIO[57] X[0] TXD -- SIUL FlexPWM_0 LIN_1 -- I/O I/O O -- Slow Medium 15 26 D[10] PCR[58] ALT0 ALT1 ALT2 ALT3 GPIO[58] A[0] CS0 -- SIUL FlexPWM_0 DSPI_3 -- I/O O I/O -- Slow Medium 53 76 D[11] PCR[59] ALT0 ALT1 ALT2 ALT3 GPIO[59] B[0] CS1 SCK SIUL FlexPWM_0 DSPI_3 DSPI_3 I/O O O I/O Slow Medium 54 78 D[12] PCR[60] ALT0 ALT1 ALT2 ALT3 -- GPIO[60] X[1] -- -- RXD SIUL FlexPWM_0 -- -- LIN_1 I/O I/O -- -- I Slow Medium 70 99 D[13] PCR[61] ALT0 ALT1 ALT2 ALT3 GPIO[61] A[1] CS2 SOUT SIUL FlexPWM_0 DSPI_3 DSPI_3 I/O O O O Slow Medium 67 95 SRC = 0 SRC = 1 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 31 Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) D[14] PCR[62] ALT0 ALT1 ALT2 ALT3 -- GPIO[62] B[1] CS3 -- SIN SIUL FlexPWM_0 DSPI_3 -- DSPI_3 I/O O O -- I Slow Medium 73 105 D[15] PCR[63] ALT0 ALT1 ALT2 ALT3 -- GPIO[63] -- -- -- AN[4] SIUL -- -- -- ADC_1 Input only -- -- 41 58 SRC = 0 SRC = 1 Port E(16-bit) E[0] PCR[64] ALT0 ALT1 ALT2 ALT3 -- GPIO[64] -- -- -- AN[5] SIUL -- -- -- ADC_1 Input only -- -- 46 68 E[1] PCR[65] ALT0 ALT1 ALT2 ALT3 -- GPIO[65] -- -- -- AN[4] SIUL -- -- -- ADC_0 Input only -- -- 27 39 E[2] PCR[66] ALT0 ALT1 ALT2 ALT3 -- GPIO[66] -- -- -- AN[5] SIUL -- -- -- ADC_0 Input only -- -- 32 49 E[3] PCR[67] ALT0 ALT1 ALT2 ALT3 -- GPIO[67] -- -- -- AN[6] SIUL -- -- -- ADC_0 Input only -- -- -- 40 E[4] PCR[68] ALT0 ALT1 ALT2 ALT3 -- GPIO[68] -- -- -- AN[7] SIUL -- -- -- ADC_0 Input only -- -- -- 42 E[5] PCR[69] ALT0 ALT1 ALT2 ALT3 -- GPIO[69] -- -- -- AN[8] SIUL -- -- -- ADC_0 Input only -- -- -- 44 MPC5604P Microcontroller Data Sheet, Rev. 8 32 Freescale Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) E[6] PCR[70] ALT0 ALT1 ALT2 ALT3 -- GPIO[70] -- -- -- AN[9] SIUL -- -- -- ADC_0 Input only -- -- -- 46 E[7] PCR[71] ALT0 ALT1 ALT2 ALT3 -- GPIO[71] -- -- -- AN[10] SIUL -- -- -- ADC_0 Input only -- -- -- 48 E[8] PCR[72] ALT0 ALT1 ALT2 ALT3 -- GPIO[72] -- -- -- AN[6] SIUL -- -- -- ADC_1 Input only -- -- -- 59 E[9] PCR[73] ALT0 ALT1 ALT2 ALT3 -- GPIO[73] -- -- -- AN[7] SIUL -- -- -- ADC_1 Input only -- -- -- 61 E[10] PCR[74] ALT0 ALT1 ALT2 ALT3 -- GPIO[74] -- -- -- AN[8] SIUL -- -- -- ADC_1 Input only -- -- -- 63 E[11] PCR[75] ALT0 ALT1 ALT2 ALT3 -- GPIO[75] -- -- -- AN[9] SIUL -- -- -- ADC_1 Input only -- -- -- 65 E[12] PCR[76] ALT0 ALT1 ALT2 ALT3 -- GPIO[76] -- -- -- AN[10] SIUL -- -- -- ADC_1 Input only -- -- -- 67 E[13] PCR[77] ALT0 ALT1 ALT2 ALT3 -- GPIO[77] SCK -- -- EIRQ[25] SIUL DSPI_3 -- -- SIUL I/O I/O -- -- I Slow Medium -- 117 E[14] PCR[78] ALT0 ALT1 ALT2 ALT3 -- GPIO[78] SOUT -- -- EIRQ[26] SIUL DSPI_3 -- -- SIUL I/O O -- -- I Slow Medium -- 119 SRC = 0 SRC = 1 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 33 Table 5. Pin muxing (continued) PCR[79] ALT0 ALT1 ALT2 ALT3 -- -- Functions GPIO[79] -- -- -- SIN EIRQ[27] Peripheral3 SIUL -- -- -- DSPI_3 SIUL I/O direction4 Pin No. SRC = 0 SRC = 1 144-pin E[15] Pad speed5 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) I/O -- -- -- I I Slow Medium -- 121 Port F (16-bit) F[0] PCR[80] ALT0 ALT1 ALT2 ALT3 -- GPIO[80] DBG0 CS3 -- EIRQ[28] SIUL FlexRay_0 DSPI_3 -- SIUL I/O O O -- I Slow Medium -- 133 F[1] PCR[81] ALT0 ALT1 ALT2 ALT3 -- GPIO[81] DBG1 CS2 -- EIRQ[29] SIUL FlexRay_0 DSPI_3 -- SIUL I/O O O -- I Slow Medium -- 135 F[2] PCR[82] ALT0 ALT1 ALT2 ALT3 GPIO[82] DBG2 CS1 -- SIUL FlexRay_0 DSPI_3 -- I/O O O -- Slow Medium -- 137 F[3] PCR[83] ALT0 ALT1 ALT2 ALT3 GPIO[83] DBG3 CS0 -- SIUL FlexRay_0 DSPI_3 -- I/O O I/O -- Slow Medium -- 139 F[4] PCR[84] ALT0 ALT1 ALT2 ALT3 GPIO[84] MDO[3] -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 4 F[5] PCR[85] ALT0 ALT1 ALT2 ALT3 GPIO[85] MDO[2] -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 5 F[6] PCR[86] ALT0 ALT1 ALT2 ALT3 GPIO[86] MDO[1] -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 8 F[7] PCR[87] ALT0 ALT1 ALT2 ALT3 GPIO[87] MCKO -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 19 F[8] PCR[88] ALT0 ALT1 ALT2 ALT3 GPIO[88] MSEO1 -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 20 MPC5604P Microcontroller Data Sheet, Rev. 8 34 Freescale Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) F[9] PCR[89] ALT0 ALT1 ALT2 ALT3 GPIO[89] MSEO0 -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 23 F[10] PCR[90] ALT0 ALT1 ALT2 ALT3 GPIO[90] EVTO -- -- SIUL NEXUS_0 -- -- I/O O -- -- Slow Fast -- 24 F[11] PCR[91] ALT0 ALT1 ALT2 ALT3 -- GPIO[91] -- -- -- EVTI SIUL -- -- -- NEXUS_0 I/O -- -- -- I Slow Medium -- 25 F[12] PCR[92] ALT0 ALT1 ALT2 ALT3 GPIO[92] ETC[3] -- -- SIUL eTimer_1 -- -- I/O I/O -- -- Slow Medium -- 106 F[13] PCR[93] ALT0 ALT1 ALT2 ALT3 GPIO[92] ETC[4] -- -- SIUL eTimer_1 -- -- I/O I/O -- -- Slow Medium -- 112 F[14] PCR[94] ALT0 ALT1 ALT2 ALT3 GPIO[94] TXD -- -- SIUL LIN_1 -- -- I/O O -- -- Slow Medium -- 115 F[15] PCR[95] ALT0 ALT1 ALT2 ALT3 -- GPIO[95] -- -- -- RXD SIUL -- -- -- LIN_1 I/O -- -- -- I Slow Medium -- 113 SRC = 0 SRC = 1 Port G (12-bit) G[0] PCR[96] ALT0 ALT1 ALT2 ALT3 -- GPIO[96] F[0] -- -- EIRQ[30] SIUL FCU_0 -- -- SIUL I/O O -- -- I Slow Medium -- 38 G[1] PCR[97] ALT0 ALT1 ALT2 ALT3 -- GPIO[97] F[1] -- -- EIRQ[31] SIUL FCU_0 -- -- SIUL I/O O -- -- I Slow Medium -- 141 G[2] PCR[98] ALT0 ALT1 ALT2 ALT3 GPIO[98] X[2] -- -- SIUL FlexPWM_0 -- -- I/O I/O -- -- Slow Medium -- 102 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 35 Table 5. Pin muxing (continued) Pad speed5 Peripheral3 Pin No. 144-pin Functions I/O direction4 100-pin Pad Port Alternate configuration pin function1,2 register (PCR) G[3] PCR[99] ALT0 ALT1 ALT2 ALT3 GPIO[99] A[2] -- -- SIUL FlexPWM_0 -- -- I/O O -- -- Slow Medium -- 104 G[4] PCR[100] ALT0 ALT1 ALT2 ALT3 GPIO[100] B[2] -- -- SIUL FlexPWM_0 -- -- I/O O -- -- Slow Medium -- 100 G[5] PCR[101] ALT0 ALT1 ALT2 ALT3 GPIO[101] X[3] -- -- SIUL FlexPWM_0 -- -- I/O I/O -- -- Slow Medium -- 85 G[6] PCR[102] ALT0 ALT1 ALT2 ALT3 GPIO[102] A[3] -- -- SIUL FlexPWM_0 -- -- I/O O -- -- Slow Medium -- 98 G[7] PCR[103] ALT0 ALT1 ALT2 ALT3 GPIO[103] B[3] -- -- SIUL FlexPWM_0 -- -- I/O O -- -- Slow Medium -- 83 G[8] PCR[104] ALT0 ALT1 ALT2 ALT3 -- GPIO[104] -- -- -- FAULT[0] SIUL -- -- -- FlexPWM_0 I/O -- -- -- I Slow Medium -- 81 G[9] PCR[105] ALT0 ALT1 ALT2 ALT3 -- GPIO[105] -- -- -- FAULT[1] SIUL -- -- -- FlexPWM_0 I/O -- -- -- I Slow Medium -- 79 G[10] PCR[106] ALT0 ALT1 ALT2 ALT3 -- GPIO[106] -- -- -- FAULT[2] SIUL -- -- -- FlexPWM_0 I/O -- -- -- I Slow Medium -- 77 G[11] PCR[107] ALT0 ALT1 ALT2 ALT3 -- GPIO[107] -- -- -- FAULT[3] SIUL -- -- -- FlexPWM_0 I/O -- -- -- I Slow Medium -- 75 1 SRC = 0 SRC = 1 ALT0 is the primary (default) function for each port after reset. MPC5604P Microcontroller Data Sheet, Rev. 8 36 Freescale 2 3 4 5 6 Alternate functions are chosen by setting the values of the PCR[PA] bitfields inside the SIU module. PCR[PA] = 00 ALT0; PCR[PA] = 01 ALT1; PCR[PA] = 10 ALT2; PCR[PA] = 11 ALT3. This is intended to select the output functions; to use one of the input-only functions, the PCR[IBE] bit must be written to `1', regardless of the values selected in the PCR[PA] bitfields. For this reason, the value corresponding to an input only function is reported as "--". Module included on the MCU. Multiple inputs are routed to all respective modules internally. The input of some modules must be configured by setting the values of the PSMI[PADSELx] bitfields inside the SIUL module. Programmable via the SRC (Slew Rate Control) bits in the respective Pad Configuration Register. Weak pull down during reset. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 37 3 Electrical characteristics 3.1 Introduction This section contains device electrical characteristics as well as temperature and power considerations. This microcontroller contains input protection against damage due to high static voltages. However, it is advisable to take precautions to avoid application of any voltage higher than the specified maximum rated voltages. To enhance reliability, unused inputs can be driven to an appropriate logic voltage level (VDD or VSS). This can be done by the internal pull-up or pull-down resistors, which are provided by the device for most general purpose pins. The following tables provide the device characteristics and its demands on the system. In the tables where the device logic provides signals with their respective timing characteristics, the symbol "CC" for Controller Characteristics is included in the Symbol column. In the tables where the external system must provide signals with their respective timing characteristics to the device, the symbol "SR" for System Requirement is included in the Symbol column. CAUTION All of the following parameter values can vary depending on the application and must be confirmed during silicon characterization or silicon reliability trial. 3.2 Parameter classification The electrical parameters are guaranteed by various methods. To give the customer a better understanding, the classifications listed in Table 6 are used and the parameters are tagged accordingly in the tables where appropriate. Table 6. Parameter classifications Classification tag Tag description P Those parameters are guaranteed during production testing on each individual device. C Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. T Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. D Those parameters are derived mainly from simulations. NOTE The classification is shown in the column labeled "C" in the parameter tables where appropriate. MPC5604P Microcontroller Data Sheet, Rev. 8 38 Freescale 3.3 Absolute maximum ratings Table 7. Absolute maximum ratings1 Value Symbol VSS Parameter Conditions Min Max2 Unit SR Device ground -- 0 0 V SR 3.3 V / 5.0 V input/output supply voltage with respect to ground (VSS) -- -0.3 6.0 V VSS_HV_IOx SR Input/output ground voltage with respect to ground (VSS) -- -0.1 0.1 V VDD_HV_FL -- SR 3.3 V / 5.0 V code and data flash supply voltage with respect to ground Relative to (VSS) VDD_HV_IOx -0.3 6.0 V VDD_HV_IOx 3 VSS_HV_FL SR Code and data flash ground with respect to ground (VSS) -- VDD_HV_OSC SR 3.3 V / 5.0 V crystal oscillator -- amplifier supply voltage with respect Relative to to ground (VSS) VDD_HV_IOx VDD_HV_IOx + 0.3 -0.1 0.1 V -0.3 6.0 V VDD_HV_IOx + 0.3 VSS_HV_OSC SR 3.3 V / 5.0 V crystal oscillator amplifier reference voltage with respect to ground (VSS) -- -0.1 0.1 V VDD_HV_REG SR 3.3 V / 5.0 V voltage regulator supply voltage with respect to ground (VSS) -- -0.3 6.0 V VDD_HV_ADC04 SR 3.3 V / 5.0 V ADC_0 supply and high VDD_HV_REG < reference voltage with respect to 2.7 V ground (VSS) VDD_HV_REG > 2.7 V VSS_HV_ADC0 SR ADC_0 ground and low reference voltage with respect to ground (VSS) -- VDD_HV_ADC14 SR 3.3 V / 5.0 V ADC_0 supply and high VDD_HV_REG < reference voltage with respect to 2.7 V ground (VSS) VDD_HV_REG > 2.7 V VIN -0.3 VDD_HV_REG + 0.3 V 6.0 -0.1 0.1 V -0.3 VDD_HV_REG + 0.3 V 6.0 -- -0.1 0.1 V SR Slope characteristics on all VDD during power up5 with respect to ground (VSS) -- 3.0 500 x 103 (0.5 [V/s]) V/s SR Voltage on any pin with respect to ground (VSS_HV_IOx) with respect to ground (VSS) -- -0.3 6.0 V VSS_HV_ADC1 SR ADC_1 ground and low reference voltage with respect to ground (VSS) TVDD VDD_HV_IOx + 0.3 Relative to VDD_HV_IOx Relative to VDD_HV_IOx VDD_HV_IOx + 0. 3 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 39 Table 7. Absolute maximum ratings1 (continued) Value Symbol Parameter Conditions Min VINAN0 VINAN1 3 4 5 6 7 SR ADC1 analog input voltage7 VDD_HV_REG > VSS_HV_ADV0 VDD_HV_ADV0 + 2.7 V 0.3 0.3 V VDD_HV_REG < 2.7 V V VSS_HV_ADV0 VDD_HV_ADV0 VDD_HV_REG > VSS_HV_ADV1 VDD_HV_ADV1 + 2.7 V 0.3 0.3 V VDD_HV_REG < 2.7 V VSS_HV_ADV1 VDD_HV_ADV1 V SR Injected input current on any pin during overload condition -- -10 10 mA IINJSUM SR Absolute sum of all injected input currents during overload condition -- -50 50 mA IVDD_LV SR Low voltage static current sink through VDD_LV -- -- 155 mA SR Storage temperature -- -55 150 C SR Junction temperature under bias -- -40 150 C TJ 2 ADC0 and shared ADC0/1 analog input voltage6 Unit IINJPAD TSTG 1 SR Max2 Functional operating conditions are given in the DC electrical characteristics. Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the listed maxima may affect device reliability or cause permanent damage to the device. Absolute maximum voltages are currently maximum burn-in voltages. Absolute maximum specifications for device stress have not yet been determined. The difference between each couple of voltage supplies must be less than 300 mV, |VDD_HV_IOy - VDD_HV_IOx | < 300 mV. The difference between ADC voltage supplies must be less than 100 mV, |VDD_HV_ADC1 - VDD_HV_ADC0| < 100 mV. Guaranteed by device validation Not allowed to refer this voltage to VDD_HV_ADV1, VSS_HV_ADV1 Not allowed to refer this voltage to VDD_HV_ADV0, VSS_HV_ADV0 Figure 4 shows the constraints of the different power supplies. MPC5604P Microcontroller Data Sheet, Rev. 8 40 Freescale VDD_HV_xxx 6.0 V VDD_HV_IOx -0.3 V -0.3 V 6.0 V Figure 4. Power supplies constraints (-0.3 V VDD_HV_IOx 6.0 V) The MPC5604P supply architecture allows of having ADC supply managed independently from standard VDD_HV supply. Figure 5 shows the constraints of the ADC power supply. VDD_HV_ADCx 6.0 V VDD_HV_REG -0.3 V -0.3 V 2.7 V 6.0 V Figure 5. Independent ADC supply (-0.3 V VDD_HV_REG 6.0 V) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 41 3.4 Recommended operating conditions Table 8. Recommended operating conditions (5.0 V) Value Symbol Parameter Conditions Min Max1 Unit SR Device ground -- 0 0 V VDD_HV_IOx2 SR 5.0 V input/output supply voltage -- 4.5 5.5 V VSS_HV_IOx SR Input/output ground voltage -- 0 0 V VDD_HV_FL SR 5.0 V code and data flash supply voltage -- 4.5 5.5 V VSS VSS_HV_FL VDD_HV_OSC Relative to VDD_HV_IOx VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 SR Code and data flash ground -- 0 0 V SR 5.0 V crystal oscillator amplifier supply voltage -- 4.5 5.5 V Relative to VDD_HV_IOx VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 VSS_HV_OSC SR 5.0 V crystal oscillator amplifier reference voltage -- 0 0 V VDD_HV_REG SR 5.0 V voltage regulator supply voltage -- 4.5 5.5 V VDD_HV_ADC03 SR 5.0 V ADC_0 supply and high reference voltage Relative to VDD_HV_IOx -- Relative to VDD_HV_REG VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 4.5 5.5 VDD_HV_REG - 0.1 -- V VSS_HV_ADC0 SR ADC_0 ground and low reference voltage -- 0 0 V VDD_HV_ADC13 SR 5.0 V ADC_1 supply and high reference voltage -- 4.5 5.5 V VDD_HV_REG - 0.1 -- -- 0 0 V -- -- -- V -- 0 0 V CC Internal supply voltage -- -- -- V SR Internal reference voltage -- 0 0 V SR Ambient temperature under bias -- -40 125 C VSS_HV_ADC1 SR ADC_1 ground and low reference voltage VDD_LV_REGCOR4,5 CC Internal supply voltage VSS_LV_REGCOR4 SR Internal reference voltage VDD_LV_CORx 4,5 VSS_LV_CORx4 TA Relative to VDD_HV_REG 1 Parametric figures can be out of specification when voltage drops below 4.5 V, however, guaranteeing the full functionality. In particular, ADC electrical characteristics and I/Os DC electrical specification may not be guaranteed. 2 The difference between each couple of voltage supplies must be less than 100 mV, |V DD_HV_IOy - VDD_HV_IOx | < 100 mV. 3 The difference between ADC voltage supplies must be less than 100 mV, |VDD_HV_ADC1 VDD_HV_ADC0| < 100 mV. MPC5604P Microcontroller Data Sheet, Rev. 8 42 Freescale 4 To be connected to emitter of external NPN. Low voltage supplies are not under user control--they are produced by an on-chip voltage regulator--but for the device to function properly the low voltage grounds (VSS_LV_xxx) must be shorted to high voltage grounds (VSS_HV_xxx) and the low voltage supply pins (VDD_LV_xxx) must be connected to the external ballast emitter. 5 The low voltage supplies (VDD_LV_xxx) are not all independent. VDD_LV_COR1 and VDD_LV_COR2 are shorted internally via double bonding connections with lines that provide the low voltage supply to the data flash module. Similarly, VSS_LV_COR1 and VSS_LV_COR2 are internally shorted. VDD_LV_REGCOR and VDD_LV_REGCORx are physically shorted internally, as are VSS_LV_REGCOR and VSS_LV_CORx. Table 9. Recommended operating conditions (3.3 V) Value Symbol VSS Parameter Conditions Min Max1 Unit SR Device ground -- 0 0 V SR 3.3 V input/output supply voltage -- 3.0 3.6 V VSS_HV_IOx SR Input/output ground voltage -- 0 0 V VDD_HV_FL SR 3.3 V code and data flash supply voltage -- 3.0 3.6 V VDD_HV_IOx 2 VSS_HV_FL VDD_HV_OSC Relative to VDD_HV_IOx VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 SR Code and data flash ground -- 0 0 V SR 3.3 V crystal oscillator amplifier supply voltage -- 3.0 3.6 V Relative to VDD_HV_IOx VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 VSS_HV_OSC SR 3.3 V crystal oscillator amplifier reference voltage -- 0 0 V VDD_HV_REG SR 3.3 V voltage regulator supply voltage -- 3.0 3.6 V VDD_HV_ADC03 SR 3.3 V ADC_0 supply and high reference voltage Relative to VDD_HV_IOx -- Relative to VDD_HV_REG VDD_HV_IOx - 0.1 VDD_HV_IOx + 0.1 3.0 5.5 VDD_HV_REG - 0.1 5.5 V VSS_HV_ADC0 SR ADC_0 ground and low reference voltage -- 0 0 V VDD_HV_ADC13 SR 3.3 V ADC_1 supply and high reference voltage -- 3.0 5.5 V VDD_HV_REG - 0.1 5.5 -- 0 0 V -- -- -- V VSS_HV_ADC1 SR ADC_1 ground and low reference voltage VDD_LV_REGCOR4,5 CC Internal supply voltage Relative to VDD_HV_REG MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 43 Table 9. Recommended operating conditions (3.3 V) (continued) Value Symbol Parameter VDD_LV_CORx VSS_LV_CORx4 TA 1 2 3 4 5 Unit Min Max1 -- 0 0 V CC Internal supply voltage -- -- -- V SR Internal reference voltage -- 0 0 V SR Ambient temperature under bias -- -40 125 C VSS_LV_REGCOR4 SR Internal reference voltage 4,5 Conditions Parametric figures can be out of specification when voltage drops below 4.5 V, however, guaranteeing the full functionality. In particular, ADC electrical characteristics and I/Os DC electrical specification may not be guaranteed. The difference between each couple of voltage supplies must be less than 100 mV, |VDD_HV_IOy - VDD_HV_IOx | < 100 mV. The difference between each couple of voltage supplies must be less than 100 mV, |VDD_HV_ADC1 - VDD_HV_ADC0| < 100 mV. As long as that condition is met, ADC_0 and ADC_1 can be operated at 5 V with the rest of the device operating at 3.3 V. To be connected to emitter of external NPN. Low voltage supplies are not under user control--they are produced by an on-chip voltage regulator--but for the device to function properly the low voltage grounds (VSS_LV_xxx) must be shorted to high voltage grounds (VSS_HV_xxx) and the low voltage supply pins (VDD_LV_xxx) must be connected to the external ballast emitter. The low voltage supplies (VDD_LV_xxx) are not all independent. VDD_LV_COR1 and VDD_LV_COR2 are shorted internally via double bonding connections with lines that provide the low voltage supply to the data flash module. Similarly, VSS_LV_COR1 and VSS_LV_COR2 are internally shorted. VDD_LV_REGCOR and VDD_LV_REGCORx are physically shorted internally, as are VSS_LV_REGCOR and VSS_LV_CORx. MPC5604P Microcontroller Data Sheet, Rev. 8 44 Freescale Figure 6 shows the constraints of the different power supplies. VDD_HV_xxx 5.5 V 3.3 V 3.0 V VDD_HV_IOx 3.0 V 5.5 V 3.3 V Note: IO AC and DC characteristics are guaranteed only in the range of 3.0-3.6 V when PAD3V5V is low, and in the range of 4.5-5.5 V when PAD3V5V is high. Figure 6. Power supplies constraints (3.0 V VDD_HV_IOx 5.5 V) The MPC5604P supply architecture allows the ADC supply to be managed independently from the standard VDD_HV supply. Figure 7 shows the constraints of the ADC power supply. VDD_HV_ADCx 5.5 V 3.0 V VDD_HV_REG 3.0 V 5.5 V Figure 7. Independent ADC supply (3.0 V VDD_HV_REG 5.5 V) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 45 3.5 Thermal characteristics 3.5.1 Package thermal characteristics Table 10. Thermal characteristics for 144-pin LQFP Symbol RJA RJB Parameter Conditions Thermal resistance junction-to-ambient, natural convection1 2 Thermal resistance junction-to-board Typical value Unit Single layer board--1s 54.2 C/W Four layer board--2s2p 44.4 C/W Four layer board--2s2p 29.9 C/W 9.3 C/W Operating conditions 30.2 C/W Operating conditions 0.8 C/W RJCtop Thermal resistance junction-to-case (top)3 Single layer board--1s JB JC 1 2 3 4 5 Junction-to-board, natural convection4 Junction-to-case, natural convection5 Junction-to-ambient thermal resistance determined per JEDEC JESD51-7. Thermal test board meets JEDEC specification for this package. Junction-to-board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC specification for the specified package. Junction-to-case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used for the case temperature. Reported value includes the thermal resistance of the interface layer. Thermal characterization parameter indicating the temperature difference between the board and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JB. Thermal characterization parameter indicating the temperature difference between the case and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JC. Table 11. Thermal characteristics for 100-pin LQFP Symbol RJA RJB Parameter JC Typical value Unit Thermal resistance junction-to-ambient, natural convection1 Single layer board--1s 47.3 C/W Four layer board--2s2p 35.3 C/W Thermal resistance junction-to-board2 Four layer board--2s2p 19.1 C/W Single layer board--1s 9.7 C/W Operating conditions 19.1 C/W Operating conditions 0.8 C/W RJCtop Thermal resistance junction-to-case JB Conditions Junction-to-board, natural Junction-to-case, natural (top)3 convection4 convection5 1 Junction-to-ambient thermal resistance determined per JEDEC JESD51-7. Thermal test board meets JEDEC specification for this package. 2 Junction-to-board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC specification for the specified package. 3 Junction-to-case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used for the case temperature. Reported value includes the thermal resistance of the interface layer. 4 Thermal characterization parameter indicating the temperature difference between the board and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JB. MPC5604P Microcontroller Data Sheet, Rev. 8 46 Freescale 5 3.5.2 Thermal characterization parameter indicating the temperature difference between the case and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JC. General notes for specifications at maximum junction temperature An estimation of the chip junction temperature, TJ, can be obtained from Equation 1: TJ = TA + (RJA * PD) Eqn. 1 where: = ambient temperature for the package (C) TA RJA = junction to ambient thermal resistance (C/W) PD = power dissipation in the package (W) The junction to ambient thermal resistance is an industry standard value that provides a quick and easy estimation of thermal performance. Unfortunately, there are two values in common usage: the value determined on a single layer board and the value obtained on a board with two planes. For packages such as the PBGA, these values can be different by a factor of two. Which value is closer to the application depends on the power dissipated by other components on the board. The value obtained on a single layer board is appropriate for the tightly packed printed circuit board. The value obtained on the board with the internal planes is usually appropriate if the board has low power dissipation and the components are well separated. When a heat sink is used, the thermal resistance is expressed in Equation 2 as the sum of a junction to case thermal resistance and a case to ambient thermal resistance: RJA = RJC + RCA Eqn. 2 where: = junction to ambient thermal resistance (C/W) RJA RJC = junction to case thermal resistance (C/W) RCA = case to ambient thermal resistance (C/W) RJC is device related and cannot be influenced by the user. The user controls the thermal environment to change the case to ambient thermal resistance, RCA. For instance, the user can change the size of the heat sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit board, or change the thermal dissipation on the printed circuit board surrounding the device. To determine the junction temperature of the device in the application when heat sinks are not used, the Thermal Characterization Parameter (JT) can be used to determine the junction temperature with a measurement of the temperature at the top center of the package case using Equation 3: TJ = TT + (JT x PD) Eqn. 3 where: = thermocouple temperature on top of the package (C) TT JT = thermal characterization parameter (C/W) PD = power dissipation in the package (W) The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire. References: MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 47 Semiconductor Equipment and Materials International 3081 Zanker Road San Jose, CA 95134 U.S.A. (408) 943-6900 MIL-SPEC and EIA/JESD (JEDEC) specifications are available from Global Engineering Documents at 800-854-7179 or 303-397-7956. JEDEC specifications are available on the WEB at http://www.jedec.org. 1. 2. 3. 3.6 C.E. Triplett and B. Joiner, An Experimental Characterization of a 272 PBGA Within an Automotive Engine Controller Module, Proceedings of SemiTherm, San Diego, 1998, pp. 47-54. G. Kromann, S. Shidore, and S. Addison, Thermal Modeling of a PBGA for Air-Cooled Applications, Electronic Packaging and Production, pp. 53-58, March 1998. B. Joiner and V. Adams, Measurement and Simulation of Junction to Board Thermal Resistance and Its Application in Thermal Modeling, Proceedings of SemiTherm, San Diego, 1999, pp. 212-220. Electromagnetic interference (EMI) characteristics Table 12. EMI testing specifications Symbol VEME 3.7 Parameter Conditions Clocks Level Unit (Max) Frequency 150 kHz-150 MHz Radiated emissions Device configuration, test fOSC 8 MHz conditions and EM testing per fCPU 64 MHz 150-1000 MHz No PLL frequency standard IEC61967-2 modulation IEC Level Supply voltage = 5 V DC 150 kHz-150 MHz Ambient temperature = 25 C fOSC 8 MHz fCPU 64 MHz Worst-case orientation 150-1000 MHz 1% PLL frequency modulation IEC Level 16 dBV 15 M -- 15 dBV 14 M -- Electrostatic discharge (ESD) characteristics Table 13. ESD ratings1,2 Symbol Parameter Conditions Value Unit VESD(HBM) SR Electrostatic discharge (Human Body Model) -- 2000 V VESD(CDM) SR Electrostatic discharge (Charged Device Model) -- 750 (corners) V 500 (other) 1 All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits. 2 A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device specification requirements. Complete DC parametric and functional testing shall be performed per applicable device specification at room temperature followed by hot temperature, unless specified otherwise in the device specification. MPC5604P Microcontroller Data Sheet, Rev. 8 48 Freescale 3.8 3.8.1 Power management electrical characteristics Voltage regulator electrical characteristics The internal voltage regulator requires an external NPN ballast to be connected as shown in Figure 8. Table 14 contains all approved NPN ballast components. Capacitances should be placed on the board as near as possible to the associated pins. Care should also be taken to limit the serial inductance of the VDD_HV_REG, BCTRL and VDD_LV_CORx pins to less than LReg, see Table 15. NOTE The voltage regulator output cannot be used to drive external circuits. Output pins are used only for decoupling capacitances. VDD_LV_COR must be generated using internal regulator and external NPN transistor. It is not possible to provide VDD_LV_COR through external regulator. For the MPC5604P microcontroller, capacitors, with total values not below CDEC1, should be placed between VDD_LV_CORx/VSS_LV_CORx close to external ballast transistor emitter. 4 capacitors, with total values not below CDEC2, should be placed close to microcontroller pins between each VDD_LV_CORx/VSS_LV_CORx supply pairs and the VDD_LV_REGCOR/VSS_LV_REGCOR pair . Additionally, capacitors with total values not below CDEC3, should be placed between the VDD_HV_REG/VSS_HV_REG pins close to ballast collector. Capacitors values have to take into account capacitor accuracy, aging and variation versus temperature. All reported information are valid for voltage and temperature ranges described in recommended operating condition, Table 8 and Table 9. VDD_HV_REG CDEC3 MPC5604P BJT(1) BCTRL RB VDD_LV_COR CDEC2 1 CDEC1 Refer to Table 14. Figure 8. Configuration with resistor on base MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 49 Table 14. Approved NPN ballast components (configuration with resistor on base) Part Manufacturer Approved derivatives1 BCP68 ON Semi BCP68 NXP BCP68-25 Infineon BCP68-25 BCX68 Infineon BCX68-10;BCX68-16;BCX68-25 BC868 NXP BC868 BC817 Infineon BC817-16;BC817-25;BC817SU; NXP BC817-16;BC817-25 ST BCP56-16 Infineon BCP56-10;BCP56-16 ON Semi BCP56-10 NXP BCP56-10;BCP56-16 BCP56 1 For automotive applications please check with the appropriate transistor vendor for automotive grade certification Table 15. Voltage regulator electrical characteristics (configuration with resistor on base) Value Symbol C Parameter Conditions Unit Min VDD_LV_REGCOR CC P Output voltage under maximum Post-trimming load run supply current configuration RB CDEC1 Typ Max 1.15 -- 1.32 V 18 -- 22 k -- F SR -- External resistance on bipolar junction transistor (BJT) base -- SR -- External decoupling/stability ceramic capacitor BJT from Table 14. 3 19.5 capacitances (i.e. X7R or X8R capacitors) with nominal value of 10 F 30 BJT BC817, one capacitance of 22 F 22 14.3 F MPC5604P Microcontroller Data Sheet, Rev. 8 50 Freescale Table 15. Voltage regulator electrical characteristics (configuration with resistor on base) (continued) Value Symbol C Parameter Conditions Unit Min RREG SR -- Resulting ESR of all three capacitors of CDEC1 Resulting ESR of the unique capacitor CDEC1 Typ Max BJT from Table 14. 3x10 F. Absolute maximum value between 100 kHz and 10 MHz -- -- 50 m BJT BC817, 1x 22 F. Absolute maximum value between 100 kHz and 10 MHz 10 -- 40 m CDEC2 SR -- External decoupling/stability ceramic capacitor 4 capacitances (i.e. X7R or 1200 1760 X8R capacitors) with nominal value of 440 nF -- nF CDEC3 SR -- External decoupling/stability ceramic capacitor on VDD_HV_REG 3 capacitances (i.e. X7R or X8R capacitors) with nominal value of 10 F; CDEC3 has to be equal or greater than CDEC1 LReg SR -- Resulting ESL of VDD_HV_REG, -- BCTRL and VDD_LV_CORx pins 19.5 30 -- F -- -- 15 nH VDD_HV_REG CDEC3 MPC5604P BCP56, BCP68, BCX68, BC817 BCTRL VDD_LV_COR CDEC2 CDEC1 Figure 9. Configuration without resistor on base MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 51 Table 16. Voltage regulator electrical characteristics (configuration without resistor on base) Value Symbol C Parameter Conditions Unit Min VDD_LV_REGCOR CC P Output voltage under maximum Post-trimming load run supply current configuration 3.8.2 1.15 1.32 V -- CDEC1 SR -- External decoupling/stability ceramic capacitor RREG SR -- Resulting ESR of all four CDEC1 Absolute maximum value between 100 kHz and 10 MHz CDEC2 SR -- External decoupling/stability ceramic capacitor CDEC3 SR -- External decoupling/stability ceramic capacitor on VDD_HV_REG LReg Typ Max 4 capacitances 4 capacitances of 100 nF each 40 56 -- -- -- 45 400 -- -- 40 -- -- -- -- 15 F m nF F -- SR -- Resulting ESL of VDD_HV_REG, -- BCTRL and VDD_LV_CORx pins nH Voltage monitor electrical characteristics The device implements a Power-on Reset module to ensure correct power-up initialization, as well as three low voltage detectors to monitor the VDD and the VDD_LV voltage while device is supplied: * * * * POR monitors VDD during the power-up phase to ensure device is maintained in a safe reset state LVDHV3 monitors VDD to ensure device reset below minimum functional supply LVDHV5 monitors VDD when application uses device in the 5.0V 10% range LVDLVCOR monitors low voltage digital power domain Table 17. Low voltage monitor electrical characteristics Symbol C Parameter Value Conditions1 Unit Min Max -- 1.5 2.7 V TA = 25 C 1.0 -- V VPORH T Power-on reset threshold VPORUP P Supply for functional POR module VREGLVDMOK_H P Regulator low voltage detector high threshold -- -- 2.95 V VREGLVDMOK_L P Regulator low voltage detector low threshold -- 2.6 -- V VFLLVDMOK_H P Flash low voltage detector high threshold -- -- 2.95 V VFLLVDMOK_L P Flash low voltage detector low threshold -- 2.6 -- V VIOLVDMOK_H P I/O low voltage detector high threshold -- -- 2.95 V VIOLVDMOK_L P I/O low voltage detector low threshold -- 2.6 -- V MPC5604P Microcontroller Data Sheet, Rev. 8 52 Freescale Table 17. Low voltage monitor electrical characteristics (continued) Symbol 1 C Value Conditions1 Parameter Unit Min Max VIOLVDM5OK_H P I/O 5V low voltage detector high threshold -- -- 4.4 V VIOLVDM5OK_L P I/O 5V low voltage detector low threshold -- 3.8 -- V VMLVDDOK_H P Digital supply low voltage detector high -- -- 1.145 V VMLVDDOK_L P Digital supply low voltage detector low -- 1.08 -- V VDD = 3.3V 10% / 5.0V 10%, TA = -40 C to TA MAX, unless otherwise specified 3.9 Power up/down sequencing To prevent an overstress event or a malfunction within and outside the device, the MPC5604P implements the following sequence to ensure each module is started only when all conditions for switching it ON are available: * * * A POWER_ON module working on voltage regulator supply controls the correct start-up of the regulator. This is a key module ensuring safe configuration for all voltage regulator functionality when supply is below 1.5V. Associated POWER_ON (or POR) signal is active low. Several low voltage detectors, working on voltage regulator supply monitor the voltage of the critical modules (voltage regulator, I/Os, flash memory and low voltage domain). LVDs are gated low when POWER_ON is active. A POWER_OK signal is generated when all critical supplies monitored by the LVD are available. This signal is active high and released to all modules including I/Os, flash memory and RC16 oscillator needed during power-up phase and reset phase. When POWER_OK is low the associated module are set into a safe state. VPORH VDD_HV_REG VLVDHV3H 3.3V VPOR_UP 0V 3.3V POWER_ON 0V 3.3V LVDM (HV) 0V VMLVDOK_H VDD_LV_REGCOR 1.2V 0V 3.3V LVDD (LV) 0V 3.3V POWER_OK 0V RC16MHz Oscillator Internal Reset Generation Module FSM 1.2V 0V ~1us P0 P1 1.2V 0V Figure 10. Power-up typical sequence MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 53 VLVDHV3L VDD_HV_REG 3.3V VPORH 0V 3.3V LVDM (HV) 0V 3.3V POWER_ON 0V 1.2V 0V VDD_LV_REGCOR 3.3V LVDD (LV) 0V 3.3V POWER_OK 0V RC16MHz Oscillator 1.2V 0V Internal Reset Generation Module FSM IDLE 1.2V 0V P0 Figure 11. Power-down typical sequence VLVDHV3L VLVDHV3H 3.3V VDD_HV_REG 0V 3.3V LVDM (HV) 0V 3.3V POWER_ON 0V 1.2V 0V VDD_LV_REGCOR 3.3V LVDD (LV) 0V 3.3V POWER_OK 0V RC16MHz Oscillator 1.2V 0V ~1us Internal Reset Generation Module FSM IDLE P0 P1 1.2V 0V Figure 12. Brown-out typical sequence MPC5604P Microcontroller Data Sheet, Rev. 8 54 Freescale 3.10 DC electrical characteristics 3.10.1 NVUSRO register Portions of the device configuration, such as high voltage supply, and watchdog enable/disable after reset are controlled via bit values in the non-volatile user options (NVUSRO) register. For a detailed description of the NVUSRO register, please refer to the device reference manual. 3.10.1.1 NVUSRO[PAD3V5V] field description The DC electrical characteristics are dependent on the PAD3V5V bit value. Table 18 shows how NVUSRO[PAD3V5V] controls the device configuration. Table 18. PAD3V5V field description Value1 1 3.10.2 Description 0 High voltage supply is 5.0 V 1 High voltage supply is 3.3 V Default manufacturing value before flash initialization is `1' (3.3 V). DC electrical characteristics (5 V) Table 19 gives the DC electrical characteristics at 5 V (4.5 V < VDD_HV_IOx < 5.5 V, NVUSRO[PAD3V5V] = 0); see Figure 13. Table 19. DC electrical characteristics (5.0 V, NVUSRO[PAD3V5V] = 0) Value Symbol C VIL VIH Parameter Conditions Unit Min Max D Low level input voltage -- -0.11 -- V P -- -- 0.35 VDD_HV_IOx V P High level input voltage -- 0.65 VDD_HV_IOx -- V VDD_HV_IOx + 0.11 V D -- -- VHYS T Schmitt trigger hysteresis -- 0.1 VDD_HV_IOx -- V VOL_S P Slow, low level output voltage IOL = 3 mA -- 0.1 VDD_HV_IOx V VOH_S P Slow, high level output voltage IOH = -3 mA 0.8 VDD_HV_IOx -- V VOL_M P Medium, low level output voltage IOL = 3 mA -- 0.1 VDD_HV_IOx V VOH_M P Medium, high level output voltage IOH = -3 mA 0.8 VDD_HV_IOx -- V VOL_F P Fast, low level output voltage IOL = 3 mA -- 0.1 VDD_HV_IOx V VOH_F P Fast, high level output voltage IOH = -3 mA 0.8 VDD_HV_IOx -- V VOL_SYM P Symmetric, low level output voltage IOL = 3 mA -- 0.1 VDD_HV_IOx V VOH_SYM P Symmetric, high level output voltage IOH = -3 mA 0.8 VDD_HV_IOx -- V VIN = VIL -130 -- A VIN = VIH -- -10 IPU P Equivalent pull-up current MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 55 Table 19. DC electrical characteristics (5.0 V, NVUSRO[PAD3V5V] = 0) (continued) Value Symbol C IPD 1 Parameter Conditions P Equivalent pull-down current Unit Min Max VIN = VIL 10 -- VIN = VIH -- 130 A IIL P Input leakage current (all bidirectional ports) TA = -40 to 125 C -1 1 A IIL P Input leakage current (all ADC input-only ports) TA = -40 to 125 C -0.5 0.5 A CIN D Input capacitance -- -- 10 pF IPU D RESET, equivalent pull-up current VIN = VIL -130 -- VIN = VIH -- -10 A "SR" parameter values must not exceed the absolute maximum ratings shown in Table 7. Table 20. Supply current (5.0 V, NVUSRO[PAD3V5V] = 0) Value Symbol IDD_LV_CORx C Parameter Max 40 MHz 62 77 64 MHz 71 88 40 MHz 45 56 64 MHz 52 65 VDD_LV_CORx externally forced at 1.3 V 64 MHz 60 75 HALT mode4 VDD_LV_CORx externally forced at 1.3 V -- 1.5 10 STOP mode5 VDD_LV_CORx externally forced at 1.3 V -- 1 10 Flash during read VDD_HV_FL at 5.0 V -- 10 12 Flash during erase operation on 1 VDD_HV_FL at 5.0 V flash module -- 15 19 ADC_1 3.5 5 ADC_0 3 4 ADC_1 0.8 1 RUN--Maximum mode1 T IDD_ADC T T VDD_LV_CORx externally forced at 1.3 V mode2 RUN--Maximum mode Supply current P Unit Typ RUN--Typical IDD_FLASH Conditions 3 ADC--Maximum mode1 ADC--Typical mode2 VDD_HV_ADC0 at 5.0 V VDD_HV_ADC1 at 5.0 V fADC = 16 MHz ADC_0 IDD_OSC T Oscillator VDD_OSC at 5.0 V 8 MHz mA 0.005 0.006 2.6 3.2 1 Maximum mode: FlexPWM, ADCs, CTU, DSPI, LINFlex, FlexCAN, 15 output pins, 1st and 2nd PLL enabled. I/O supply current excluded. 2 Typical mode configurations: DSPI, LINFlex, FlexCAN, 15 output pins, 1st PLL only. I/O supply current excluded. MPC5604P Microcontroller Data Sheet, Rev. 8 56 Freescale 3 Code fetched from RAM, PLL_0: 64 MHz system clock (x4 multiplier with 16 MHz XTAL), PLL_1 is ON at PHI_div2 = 120 MHz and PHI_div3 = 80 MHz, auxiliary clock sources set that all peripherals receive maximum frequency, all peripherals enabled. 4 Halt mode configurations: code fetched from RAM, code and data flash memories in low power mode, OSC/PLL_0/PLL_1 are OFF, core clock frozen, all peripherals are disabled. 5 STOP "P" mode Device Under Test (DUT) configuration: code fetched from RAM, code and data flash memories OFF, OSC/PLL_0/PLL_1 are OFF, core clock frozen, all peripherals are disabled. 3.10.3 DC electrical characteristics (3.3 V) Table 21 gives the DC electrical characteristics at 3.3 V (3.0 V < VDD_HV_IOx < 3.6 V, NVUSRO[PAD3V5V] = 1); see Figure 13. Table 21. DC electrical characteristics (3.3 V, NVUSRO[PAD3V5V] = 1)1 Value Symbol C VIL VIH Parameter Conditions Unit Min Max D Low level input voltage -- -0.12 -- V P -- -- 0.35 VDD_HV_IOx V P High level input voltage -- 0.65 VDD_HV_IOx -- V VDD_HV_IOx + 0.12 V D -- -- VHYS T Schmitt trigger hysteresis -- 0.1 VDD_HV_IOx -- V VOL_S P Slow, low level output voltage IOL = 1.5 mA -- 0.5 V VOH_S P Slow, high level output voltage IOH = -1.5 mA VDD_HV_IOx - 0.8 -- V VOL_M P Medium, low level output voltage IOL = 2 mA -- 0.5 V VOH_M P Medium, high level output voltage IOH = -2 mA VDD_HV_IOx - 0.8 -- V VOL_F P Fast, low level output voltage IOL = 1.5 mA -- 0.5 V VOH_F P Fast, high level output voltage IOH = -1.5 mA VDD_HV_IOx - 0.8 -- V VOL_SYM P Symmetric, low level output voltage IOL = 1.5 mA -- 0.5 V VOH_SYM P Symmetric, high level output voltage IOH = -1.5 mA VDD_HV_IOx - 0.8 -- V VIN = VIL -130 -- A VIN = VIH -- -10 VIN = VIL 10 -- VIN = VIH -- 130 IPU IPD 1 P Equivalent pull-up current P Equivalent pull-down current A IIL P Input leakage current (all bidirectional ports) TA = -40 to 125 C -- 1 A IIL P Input leakage current (all ADC input-only ports) TA = -40 to 125 C -- 0.5 A CIN D Input capacitance -- -- 10 pF IPU D RESET, equivalent pull-up current VIN = VIL -130 -- VIN = VIH -- -10 A These specifications are design targets and subject to change per device characterization. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 57 2 "SR" parameter values must not exceed the absolute maximum ratings shown in Table 7. Table 22. Supply current (3.3 V, NVUSRO[PAD3V5V] = 1) Value Symbol C Parameter RUN--Maximum mode1 IDD_LV_CORx T RUN--Typical IDD_FLASH IDD_ADC T T Supply current P Conditions VDD_LV_CORx externally forced at 1.3 V mode2 Unit Typ Max 40 MHz 62 77 64 MHz 71 89 40 MHz 45 56 64 MHz 53 66 RUN--Maximum mode3 VDD_LV_CORx externally forced at 1.3 V 64 MHz 60 75 HALT mode4 VDD_LV_CORx externally forced at 1.3 V -- 1.5 10 STOP mode5 VDD_LV_CORx externally forced at 1.3 V -- 1 10 Flash during read on single mode VDD_HV_FL at 3.3 V -- 8 10 Flash during erase operation on single mode VDD_HV_FL at 3.3 V -- 10 12 ADC--Maximum mode1 VDD_HV_ADC0 at 3.3 V VDD_HV_ADC1 at 3.3 V fADC = 16 MHz ADC_1 2.5 4 ADC_0 2 4 ADC_1 0.8 1 ADC--Typical mode 2 mA ADC_0 0.005 0.006 IDD_OSC 1 2 3 4 5 T Oscillator VDD_OSC at 3.3 V 8 MHz 2.4 3 Maximum mode: FlexPWM, ADCs, CTU, DSPI, LINFlex, FlexCAN, 15 output pins, 1st and 2nd PLL enabled. I/O supply current excluded. Typical mode: DSPI, LINFlex, FlexCAN, 15 output pins, 1st PLL only. I/O supply current excluded. Code fetched from RAM, PLL_0: 64 MHz system clock (x4 multiplier with 16 MHz XTAL), PLL_1 is ON at PHI_div2 = 120 MHz and PHI_div3 = 80 MHz, auxiliary clock sources set that all peripherals receive maximum frequency, all peripherals enabled. Halt mode configurations: code fetched from RAM, code and data flash memories in low power mode, OSC/PLL_0/PLL_1 are OFF, core clock frozen, all peripherals are disabled. STOP "P" mode Device Under Test (DUT) configuration: code fetched from RAM, code and data flash memories OFF, OSC/PLL_0/PLL_1 are OFF, core clock frozen, all peripherals are disabled. 3.10.4 Input DC electrical characteristics definition Figure 13 shows the DC electrical characteristics behavior as function of time. MPC5604P Microcontroller Data Sheet, Rev. 8 58 Freescale VIN VDD VIH VHYS VIL PDIx = `1' (GPDI register of SIUL) PDIx = `0' Figure 13. Input DC electrical characteristics definition 3.10.5 I/O pad current specification The I/O pads are distributed across the I/O supply segment. Each I/O supply segment is associated to a VDD/VSS supply pair as described in Table 23. Table 23. I/O supply segment Supply segment Package 1 2 3 4 5 6 7 144 LQFP pin8 - pin20 pin23 - pin38 pin39 - pin55 pin58 - pin68 pin73 - pin89 pin92 - pin125 pin128 - pin5 100 LQFP pin15 - pin26 pin27 - pin38 pin41 - pin46 pin51 - pin61 pin64 - pin86 pin89 - pin10 -- Table 24 provides the weight of concurrent switching I/Os. In order to ensure device functionality, the sum of the weight of concurrent switching I/Os on a single segment should remain below 100%. Table 24. I/O weight 144 LQFP 100 LQFP Pad Weight 5V Weight 3.3V Weight 5V Weight 3.3V NMI 1% 1% 1% 1% PAD[6] 6% 5% 14% 13% PAD[49] 5% 4% 14% 12% PAD[84] 14% 10% -- -- PAD[85] 9% 7% -- -- MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 59 Table 24. I/O weight (continued) 144 LQFP 100 LQFP Pad Weight 5V Weight 3.3V Weight 5V Weight 3.3V PAD[86] 9% 6% -- -- MODO[0] 12% 8% -- -- PAD[7] 4% 4% 11% 10% PAD[36] 5% 4% 11% 9% PAD[8] 5% 4% 10% 9% PAD[37] 5% 4% 10% 9% PAD[5] 5% 4% 9% 8% PAD[39] 5% 4% 9% 8% PAD[35] 5% 4% 8% 7% PAD[87] 12% 9% -- -- PAD[88] 9% 6% -- -- PAD[89] 10% 7% -- -- PAD[90] 15% 11% -- -- PAD[91] 6% 5% -- -- PAD[57] 8% 7% 8% 7% PAD[56] 13% 11% 13% 11% PAD[53] 14% 12% 14% 12% PAD[54] 15% 13% 15% 13% PAD[55] 25% 22% 25% 22% PAD[96] 27% 24% -- -- PAD[65] 1% 1% 1% 1% PAD[67] 1% 1% -- -- PAD[33] 1% 1% 1% 1% PAD[68] 1% 1% -- -- PAD[23] 1% 1% 1% 1% PAD[69] 1% 1% -- -- PAD[34] 1% 1% 1% 1% PAD[70] 1% 1% -- -- PAD[24] 1% 1% 1% 1% PAD[71] 1% 1% -- -- PAD[66] 1% 1% 1% 1% PAD[25] 1% 1% 1% 1% PAD[26] 1% 1% 1% 1% MPC5604P Microcontroller Data Sheet, Rev. 8 60 Freescale Table 24. I/O weight (continued) 144 LQFP 100 LQFP Pad Weight 5V Weight 3.3V Weight 5V Weight 3.3V PAD[27] 1% 1% 1% 1% PAD[28] 1% 1% 1% 1% PAD[63] 1% 1% 1% 1% PAD[72] 1% 1% -- -- PAD[29] 1% 1% 1% 1% PAD[73] 1% 1% -- -- PAD[31] 1% 1% 1% 1% PAD[74] 1% 1% -- -- PAD[30] 1% 1% 1% 1% PAD[75] 1% 1% -- -- PAD[32] 1% 1% 1% 1% PAD[76] 1% 1% -- -- PAD[64] 1% 1% 1% 1% PAD[0] 23% 20% 23% 20% PAD[1] 21% 18% 21% 18% PAD[107] 20% 17% -- -- PAD[58] 19% 16% 19% 16% PAD[106] 18% 16% -- -- PAD[59] 17% 15% 17% 15% PAD[105] 16% 14% -- -- PAD[43] 15% 13% 15% 13% PAD[104] 14% 13% -- -- PAD[44] 13% 12% 13% 12% PAD[103] 12% 11% -- -- PAD[2] 11% 10% 11% 10% PAD[101] 11% 9% -- -- PAD[21] 10% 8% 10% 8% TMS 1% 1% 1% 1% TCK 1% 1% 1% 1% PAD[20] 16% 11% 16% 11% PAD[3] 4% 3% 4% 3% PAD[61] 9% 8% 9% 8% PAD[102] 11% 10% -- -- MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 61 Table 24. I/O weight (continued) 144 LQFP 100 LQFP Pad Weight 5V Weight 3.3V Weight 5V Weight 3.3V PAD[60] 11% 10% 11% 10% PAD[100] 12% 10% -- -- PAD[45] 12% 10% 12% 10% PAD[98] 12% 11% -- -- PAD[46] 12% 11% 12% 11% PAD[99] 13% 11% -- -- PAD[62] 13% 11% 13% 11% PAD[92] 13% 12% -- -- VPP_TEST 1% 1% 1% 1% PAD[4] 14% 12% 14% 12% PAD[16] 13% 12% 13% 12% PAD[17] 13% 11% 13% 11% PAD[42] 13% 11% 13% 11% PAD[93] 12% 11% -- -- PAD[95] 12% 11% -- -- PAD[18] 12% 10% 12% 10% PAD[94] 11% 10% -- -- PAD[19] 11% 10% 11% 10% PAD[77] 10% 9% -- -- PAD[10] 10% 9% 10% 9% PAD[78] 9% 8% -- -- PAD[11] 9% 8% 9% 8% PAD[79] 8% 7% -- -- PAD[12] 7% 7% 7% 7% PAD[41] 7% 6% 7% 6% PAD[47] 5% 4% 5% 4% PAD[48] 4% 4% 4% 4% PAD[51] 4% 4% 4% 4% PAD[52] 5% 4% 5% 4% PAD[40] 5% 5% 6% 5% PAD[80] 9% 8% -- -- PAD[9] 10% 9% 11% 10% PAD[81] 10% 9% -- -- MPC5604P Microcontroller Data Sheet, Rev. 8 62 Freescale Table 24. I/O weight (continued) 144 LQFP 100 LQFP Pad Weight 5V Weight 3.3V Weight 5V Weight 3.3V PAD[13] 10% 9% 12% 11% PAD[82] 10% 9% -- -- PAD[22] 10% 9% 13% 12% PAD[83] 10% 9% -- -- PAD[50] 10% 9% 14% 12% PAD[97] 10% 9% -- -- PAD[38] 10% 9% 14% 13% PAD[14] 9% 8% 14% 13% PAD[15] 9% 8% 15% 13% Table 25. I/O consumption Symbol ISWTSLW,2 ISWTMED(2) ISWTFST(2) IRMSSLW C Value Conditions1 Parameter Unit Min Typ Max CC D Dynamic I/O current CL = 25 pF for SLOW configuration VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 20 VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 16 CC D Dynamic I/O current CL = 25 pF for MEDIUM configuration VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 29 VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 17 CC D Dynamic I/O current CL = 25 pF for FAST configuration VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 110 VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 50 CC D Root medium square CL = 25 pF, 2 MHz I/O current for SLOW CL = 25 pF, 4 MHz configuration CL = 100 pF, 2 MHz VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 2.3 -- -- 3.2 -- -- 6.6 -- -- 1.6 -- -- 2.3 -- -- 4.7 CL = 25 pF, 2 MHz CL = 25 pF, 4 MHz VDD = 3.3 V 10%, PAD3V5V = 1 CL = 100 pF, 2 MHz mA mA mA mA MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 63 Table 25. I/O consumption (continued) Symbol IRMSMED C Typ Max -- -- 6.6 -- -- 13.4 -- -- 18.3 -- -- 5 -- -- 8.5 -- -- 11 -- -- 22 -- -- 33 -- -- 56 -- -- 14 -- -- 20 CL = 100 pF, 40 MHz -- -- 35 VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 70 VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 65 CC D Root medium square CL = 25 pF, 13 MHz VDD = 5.0 V 10%, I/O current for PAD3V5V = 0 CL = 25 pF, 40 MHz MEDIUM configuration CL = 100 pF, 13 MHz CL = 25 pF, 40 MHz VDD = 3.3 V 10%, PAD3V5V = 1 CL = 100 pF, 13 MHz CC D Root medium square CL = 25 pF, 40 MHz VDD = 5.0 V 10%, I/O current for FAST PAD3V5V = 0 CL = 25 pF, 64 MHz configuration CL = 100 pF, 40 MHz CL = 25 pF, 40 MHz CL = 25 pF, 64 MHz IAVGSEG 1 2 3.11 SR D Sum of all the static I/O current within a supply segment Unit Min CL = 25 pF, 13 MHz IRMSFST Value Conditions1 Parameter VDD = 3.3 V 10%, PAD3V5V = 1 mA mA mA VDD = 3.3 V 10% / 5.0 V 10%, TA = -40 to 125 C, unless otherwise specified Stated maximum values represent peak consumption that lasts only a few ns during I/O transition. Main oscillator electrical characteristics The MPC5604P provides an oscillator/resonator driver. Table 26. Main oscillator output electrical characteristics (5.0 V, NVUSRO[PAD3V5V] = 0) Value Symbol fOSC C Parameter SR -- Oscillator frequency Unit Min Max 4 40 MHz 6.5 25 mA/V gm -- P Transconductance VOSC -- T Oscillation amplitude on XTAL pin 1 -- V T Start-up time1,2 8 -- ms tOSCSU -- 1 The start-up time is dependent upon crystal characteristics, board leakage, etc., high ESR and excessive capacitive loads can cause long start-up time. 2 Value captured when amplitude reaches 90% of XTAL MPC5604P Microcontroller Data Sheet, Rev. 8 64 Freescale Table 27. Main oscillator output electrical characteristics (3.3 V, NVUSRO[PAD3V5V] = 1) Value Symbol fOSC gm VOSC C Parameter Unit Min Max S -- Oscillator frequency R 4 40 MHz -- P Transconductance 4 20 mA/V -- 1 -- V 8 -- ms tOSCSU -- T Oscillation amplitude on XTAL pin 1,2 T Start-up time 1 The start-up time is dependent upon crystal characteristics, board leakage, etc., high ESR and excessive capacitive loads can cause long start-up time. 2 Value captured when amplitude reaches 90% of XTAL Table 28. Input clock characteristics Value Symbol Unit Min Typ Max fOSC SR Oscillator frequency 4 -- 40 MHz fCLK SR Frequency in bypass -- -- 64 MHz trCLK SR Rise/fall time in bypass -- -- 1 ns 47.5 50 52.5 % tDC 3.12 Parameter SR Duty cycle FMPLL electrical characteristics Table 29. FMPLL electrical characteristics Symbol C fref_crystal D PLL reference frequency range2 fref_ext fPLLIN fFMPLLOUT D Clock frequency range in normal mode P Free-running frequency tCYC D System clock period fLORL fLORH D Loss of reference frequency window fSCM D Self-clocked mode frequency4,5 3 Unit Min Max 4 40 MHz -- 4 16 MHz -- 16 120 MHz Measured using clock division -- typically /16 20 150 MHz -- -- 1 / fSYS ns Lower limit 1.6 3.7 MHz Upper limit 24 56 20 150 Crystal reference D Phase detector input frequency range (after pre-divider) fFREE Value Conditions1 Parameter -- MHz MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 65 Table 29. FMPLL electrical characteristics (continued) Symbol CJITTER C Parameter Short-term jitter10 T CLKOUT period jitter6,7,8,9 Value Conditions1 fSYS maximum Long-term jitter (avg. fPLLIN = 16 MHz over 2 ms interval) (resonator), fPLLCLK at 64 MHz, 4,000 cycles Unit Min Max 4 4 % fCLKOUT -- 10 ns tlpll D PLL lock time 11, 12 -- -- 200 s tdc D Duty cycle of reference -- 40 60 % fLCK D Frequency LOCK range -- 6 6 % fSYS fUL D Frequency un-LOCK range -- -18 18 % fSYS Center spread 0.25 4.013 % fSYS Down spread 0.5 8.0 -- 70 fCS fDS fMOD D Modulation depth D Modulation frequency14 -- kHz 1 VDD_LV_CORx = 1.2 V 10%; VSS = 0 V; TA = -40 to 125 C, unless otherwise specified Considering operation with PLL not bypassed 3 "Loss of Reference Frequency" window is the reference frequency range outside of which the PLL is in self-clocked mode. 4 Self-clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls outside the fLOR window. 5 f VCO self clock range is 20-150 MHz. fSCM represents fSYS after PLL output divider (ERFD) of 2 through 16 in enhanced mode. 6 This value is determined by the crystal manufacturer and board design. 7 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fSYS. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the PLL circuitry via VDDPLL and VSSPLL and variation in crystal oscillator frequency increase the CJITTER percentage for a given interval. 8 Proper PC board layout procedures must be followed to achieve specifications. 9 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of C JITTER and either fCS or fDS (depending on whether center spread or down spread modulation is enabled). 10 Short term jitter is measured on the clock rising edge at cycle n and cycle n+4. 11 This value is determined by the crystal manufacturer and board design. For 4 MHz to 20 MHz crystals specified for this PLL, load capacitors should not exceed these limits. 12 This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the synthesizer control register (SYNCR). 13 This value is true when operating at frequencies above 60 MHz, otherwise f CS is 2% (above 64 MHz). 14 Modulation depth will be attenuated from depth setting when operating at modulation frequencies above 50 kHz. 2 MPC5604P Microcontroller Data Sheet, Rev. 8 66 Freescale 3.13 16 MHz RC oscillator electrical characteristics Table 30. 16 MHz RC oscillator electrical characteristics Value Symbol fRC C Parameter P RC oscillator frequency Conditions Unit Min Typ Max TA = 25 C -- 16 -- MHz -- -5 -- 5 % RCMVAR P Fast internal RC oscillator variation over temperature and supply with respect to fRC at TA = 25 C in high-frequency configuration RCMTRIM T Post Trim Accuracy: The variation of the PTF1 from the 16 MHz TA = 25 C -1 -- 1 % RCMSTEP T Fast internal RC oscillator trimming step TA = 25 C -- 1.6 -- % 1 PTF = Post Trimming Frequency: The frequency of the output clock after trimming at typical supply voltage and temperature 3.14 Analog-to-digital converter (ADC) electrical characteristics The device provides a 10-bit successive approximation register (SAR) analog-to-digital converter. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 67 Offset Error OSE Gain Error GE 1023 1022 1021 1020 1019 1 LSB ideal = VDD_ADC / 1024 1018 (2) code out 7 (1) 6 5 (1) Example of an actual transfer curve (5) (2) The ideal transfer curve 4 (3) Differential non-linearity error (DNL) (4) (4) Integral non-linearity error (INL) 3 (5) Center of a step of the actual transfer curve (3) 2 1 1 LSB (ideal) 0 1 2 3 4 5 6 7 1017 1018 1019 1020 1021 1022 1023 Vin(A) (LSBideal) Offset Error OSE Figure 14. ADC characteristics and error definitions 3.14.1 Input impedance and ADC accuracy To preserve the accuracy of the A/D converter, it is necessary that analog input pins have low AC impedance. Placing a capacitor with good high frequency characteristics at the input pin of the device can be effective: the capacitor should be as large as possible, ideally infinite. This capacitor contributes to attenuating the noise present on the input pin; further, it sources charge during the sampling phase, when the analog signal source is a high-impedance source. A real filter can typically be obtained by using a series resistance with a capacitor on the input pin (simple RC filter). The RC filtering may be limited according to the source impedance value of the transducer or circuit supplying the analog signal to be measured. The filter at the input pins must be designed taking into account the dynamic characteristics of the input signal (bandwidth) and the equivalent input impedance of the ADC itself. MPC5604P Microcontroller Data Sheet, Rev. 8 68 Freescale In fact a current sink contributor is represented by the charge sharing effects with the sampling capacitance: CS and CP2 being substantially two switched capacitances, with a frequency equal to the ADC conversion rate, it can be seen as a resistive path to ground. For instance, assuming a conversion rate of 1 MHz, with CS+CP2 equal to 3 pF, a resistance of 330 k is obtained (REQ = 1 / (fc x (CS+CP2)), where fc represents the conversion rate at the considered channel). To minimize the error induced by the voltage partitioning between this resistance (sampled voltage on CS+CP2) and the sum of RS + RF, the external circuit must be designed to respect the Equation 4: Eqn. 4 RS + RF 1 V A --------------------- --- LSB R EQ 2 Equation 4 generates a constraint for external network design, in particular on resistive path. EXTERNAL CIRCUIT INTERNAL CIRCUIT SCHEME VDD Source RS VA Filter RF Current Limiter RL CF Channel Selection Sampling RSW1 RAD CP1 CP2 CS RS: Source impedance RF: Filter resistance CF: Filter capacitance RL: Current limiter resistance RSW1: Channel selection switch impedance RAD: Sampling switch impedance CP: Pin capacitance (two contributions, CP1 and CP2) CS: Sampling capacitance Figure 15. Input equivalent circuit A second aspect involving the capacitance network shall be considered. Assuming the three capacitances CF, CP1 and CP2 are initially charged at the source voltage VA (refer to the equivalent circuit reported in Figure 15): A charge sharing phenomenon is installed when the sampling phase is started (A/D switch closed). MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 69 Voltage Transient on CS VCS VA VA2 V <0.5 LSB 1 2 1 < (RSW + RAD) CS << TS 2 = RL (CS + CP1 + CP2) VA1 TS t Figure 16. Transient behavior during sampling phase In particular two different transient periods can be distinguished: * A first and quick charge transfer from the internal capacitance CP1 and CP2 to the sampling capacitance CS occurs (CS is supposed initially completely discharged): considering a worst case (since the time constant in reality would be faster) in which CP2 is reported in parallel to CP1 (call CP = CP1 + CP2), the two capacitances CP and CS are in series, and the time constant is CP CS 1 = R SW + R AD --------------------CP + CS Eqn. 5 Equation 5 can again be simplified considering only CS as an additional worst condition. In reality, the transient is faster, but the A/D converter circuitry has been designed to be robust also in the very worst case: the sampling time TS is always much longer than the internal time constant: Eqn. 6 1 R SW + R AD C S T S The charge of CP1 and CP2 is redistributed also on CS, determining a new value of the voltage VA1 on the capacitance according to Equation 7: Eqn. 7 V A1 C S + C P1 + C P2 = V A C P1 + C P2 * A second charge transfer involves also CF (that is typically bigger than the on-chip capacitance) through the resistance RL: again considering the worst case in which CP2 and CS were in parallel to CP1 (since the time constant in reality would be faster), the time constant is: Eqn. 8 2 R L C S + C P1 + C P2 MPC5604P Microcontroller Data Sheet, Rev. 8 70 Freescale In this case, the time constant depends on the external circuit: in particular imposing that the transient is completed well before the end of sampling time TS, a constraints on RL sizing is obtained: Eqn. 9 8.5 = 8.5 R C + C 2 L S P1 + C P2 TS Of course, RL shall be sized also according to the current limitation constraints, in combination with RS (source impedance) and RF (filter resistance). Being CF definitively bigger than CP1, CP2 and CS, then the final voltage VA2 (at the end of the charge transfer transient) will be much higher than VA1. Equation 10 must be respected (charge balance assuming now CS already charged at VA1): Eqn. 10 VA2 C S + C P1 + C P2 + C F = V A C F + V A1 C P1 + C P2 + C S The two transients above are not influenced by the voltage source that, due to the presence of the RFCF filter, is not able to provide the extra charge to compensate the voltage drop on CS with respect to the ideal source VA; the time constant RFCF of the filter is very high with respect to the sampling time (TS). The filter is typically designed to act as anti-aliasing. Analog Source Bandwidth (VA) Noise TC 2 RFCF (Conversion Rate vs. Filter Pole) fF f0 (Anti-aliasing Filtering Condition) 2 f0 fC (Nyquist) f0 f Anti-Aliasing Filter (fF = RC Filter pole) fF f Sampled Signal Spectrum (fC = conversion Rate) f0 fC f Figure 17. Spectral representation of input signal Calling f0 the bandwidth of the source signal (and as a consequence the cut-off frequency of the anti-aliasing filter, fF), according to the Nyquist theorem the conversion rate fC must be at least 2f0; it means that the constant time of the filter is greater than or at least equal to twice the conversion period (TC). Again the conversion period TC is longer than the sampling time TS, which is just a portion of it, even when fixed channel continuous conversion mode is selected (fastest conversion rate at a specific channel): in conclusion it is evident that the time constant of the filter RFCF is definitively much higher than the sampling time TS, so the charge level on CS cannot be modified by the analog signal source during the time in which the sampling switch is closed. The considerations above lead to impose new constraints on the external circuit, to reduce the accuracy error due to the voltage drop on CS; from the two charge balance equations above, it is simple to derive Equation 11 between the ideal and real sampled voltage on CS: MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 71 Eqn. 11 VA C P1 + C P2 + C F ------------ = -------------------------------------------------------V A2 C P1 + C P2 + C F + C S From this formula, in the worst case (when VA is maximum, that is for instance 5 V), assuming to accept a maximum error of half a count, a constraint is evident on CF value: Eqn. 12 C F 2048 C S 3.14.2 ADC conversion characteristics Table 31. ADC conversion characteristics Symbol C Parameter VINAN0 SR ADC0 and shared ADC0/1 analog input voltage2, 3 VINAN1 SR ADC1 analog input voltage2, 4 fCK fs tADC_S tADC_C Value Conditions1 -- Unit Min Typ Max VSS_HV_ADV -- VDD_HV_ADV 0 0 0.3 -- VSS_HV_ADV V + 0.3 -- 1 0.3 VDD_HV_ADV 1 V + 0.3 SR -- ADC clock frequency (depends on ADC configuration) (The duty cycle depends on AD_clk5 frequency) -- 36 -- 60 MHz SR -- Sampling frequency -- -- -- 1.53 MHz fADC = 20 MHz, INPSAMP = 3 125 -- -- ns fADC = 9 MHz, INPSAMP = 255 -- -- 28.2 s fADC = 20 MHz9, INPCMP = 1 0.650 -- -- s -- -- -- 1.5 s -- D Sample time7 -- P Conversion time8 tADC_PU SR -- ADC power-up delay (time needed for ADC to settle exiting from software power down; PWDN bit = 0) CS10 -- D ADC input sampling capacitance -- -- -- 2.5 pF CP110 -- D ADC input pin capacitance 1 -- -- -- 3 pF CP210 -- D ADC input pin capacitance 2 -- -- -- 1 pF MPC5604P Microcontroller Data Sheet, Rev. 8 72 Freescale Table 31. ADC conversion characteristics (continued) Symbol C Parameter RSW110 -- D Internal resistance of analog source RAD10 1 2 3 -- D Internal resistance of analog source Value Conditions1 Unit Min Typ Max VDD_HV_ADC = 5 V 10% -- -- 0.6 k VDD_HV_ADC = 3.3 V 10% -- -- 3 k -- -- 2 k -5 -- 5 mA -- IINJ -- T Input current injection Current injection on one ADC input, different from the converted one. Remains within TUE spec. INL CC P Integral non-linearity No overload -1.5 -- 1.5 LSB DNL CC P Differential non-linearity No overload -1.0 -- 1.0 LSB OSE CC T Offset error -- -- 1 -- LSB GE CC T Gain error -- -- 1 -- LSB TUE CC P Total unadjusted error without current injection -- -2.5 -- 2.5 LSB TUE CC T Total unadjusted error with current injection -- -3 -- 3 LSB VDD = 3.3 V to 3.6 V / 4.5 V to 5.5 V, TA = -40 C to TA MAX, unless otherwise specified and analog input voltage from VSS_HV_ADCx to VDD_HV_ADCx. VAINx may exceed VSS_HV_AD and VDD_HV_AD limits, remaining on absolute maximum ratings, but the results of the conversion will be clamped respectively to 0x000 or 0x3FF. Not allowed to refer this voltage to VDD_HV_ADV1, VSS_HV_ADV1 Not allowed to refer this voltage to VDD_HV_ADV0, VSS_HV_ADV0 5 AD_clk clock is always half of the ADC module input clock defined via the auxiliary clock divider for the ADC. 6 When configured to allow 60 MHz ADC, the minimum ADC clock speed is 9 MHz, below which precision is lost. 7 During the sample time the input capacitance CS can be charged/discharged by the external source. The internal resistance of the analog source must allow the capacitance to reach its final voltage level within tADC_S. After the end of the sample time tADC_S, changes of the analog input voltage have no effect on the conversion result. Values for the sample clock tADC_S depend on programming. 8 This parameter includes the sample time t ADC_S. 9 20 MHz ADC clock. Specific prescaler is programmed on MC_PLL_CLK to provide 20 MHz clock to the ADC. 10 See Figure 15. 4 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 73 3.15 Flash memory electrical characteristics Table 32. Program and erase specifications Value Symbol C Tdwprogram Parameter P Double Word (64 bits) Program Time4 4, 5 TBKPRG P Bank Program (512 KB) P Bank Program (64 1 2 3 4 5 KB)4, 5 Unit Min Typical1 Initial max2 Max3 -- 22 50 500 s -- 1.45 1.65 33 s -- 0.18 0.21 4.10 s T16kpperase P 16 KB Block Pre-program and Erase Time -- 300 500 5000 ms T32kpperase P 32 KB Block Pre-program and Erase Time -- 400 600 5000 ms T128kpperase P 128 KB Block Pre-program and Erase Time -- 800 1300 7500 ms Typical program and erase times assume nominal supply values and operation at 25 C. All times are subject to change pending device characterization. Initial factory condition: < 100 program/erase cycles, 25 C, typical supply voltage. The maximum program and erase times occur after the specified number of program/erase cycles. These maximum values are characterized but not guaranteed. Actual hardware programming times. This does not include software overhead. Typical Bank programming time assumes that all cells are programmed in a single pulse. In reality some cells will require more than one pulse, adding a small overhead to total bank programming time (see Initial Max column). Table 33. Flash memory module life Value Symbol Parameter Conditions Unit Min Typ -- P/E C Number of program/erase cycles per block for 16 KB blocks over the operating temperature range (TJ) -- 100,000 P/E C Number of program/erase cycles per block for 32 KB blocks over the operating temperature range (TJ) -- 10,000 100,000 cycles P/E C Number of program/erase cycles per block for 128 KB blocks over the operating temperature range (TJ) -- 1,000 100,000 cycles Blocks with 0-1,000 P/E cycles 20 -- years Blocks with 10,000 P/E cycles 10 -- years Blocks with 100,000 P/E cycles 5 -- years Retention 1 C C Minimum data retention at 85 C average ambient temperature1 cycles Ambient temperature averaged over duration of application, not to exceed recommended product operating temperature range. MPC5604P Microcontroller Data Sheet, Rev. 8 74 Freescale Table 34. Flash memory read access timing 1 Symbol C fmax C Parameter Maximum working frequency at given number of wait states in worst conditions Conditions1 Max value Unit 2 wait states 66 MHz 0 wait states 18 VDD = 3.3 V 10% / 5.0 V 10%, TA = -40 to 125 C, unless otherwise specified 3.16 AC specifications 3.16.1 Pad AC specifications Table 35. Output pin transition times Symbol C Value Conditions1 Parameter Unit Min Typ Max CC D Output transition time output pin2 SLOW configuration T ttr CL = 100 pF D CL = 25 pF T CL = 50 pF VDD = 5.0 V 10%, PAD3V5V = 0 VDD = 3.3 V 10%, PAD3V5V = 1 CL = 100 pF CC D Output transition time output MEDIUM configuration T pin2 CL = 25 pF CL = 50 pF D CL = 100 pF D CL = 25 pF T CL = 50 pF VDD = 5.0 V 10%, PAD3V5V = 0 SIUL.PCRx.SRC = 1 VDD = 3.3 V 10%, PAD3V5V = 1 SIUL.PCRx.SRC = 1 CL = 100 pF D 2 CC D Output transition time output pin FAST configuration ttr CL = 50 pF D D ttr CL = 25 pF CL = 25 pF CL = 50 pF VDD = 5.0 V 10%, PAD3V5V = 0 SIUL.PCRx.SRC = 1 CL = 100 pF CL = 25 pF CL = 50 pF VDD = 3.3 V 10%, PAD3V5V = 1 SIUL.PCRx.SRC = 1 CL = 100 pF tSYM 3 CC T Symmetric transition time, same drive VDD = 5.0 V 10%, PAD3V5V = 0 strength between N and P transistor VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 50 -- -- 100 -- -- 125 -- -- 40 -- -- 50 -- -- 75 -- -- 10 -- -- 20 -- -- 40 -- -- 12 -- -- 25 -- -- 40 -- -- 4 -- -- 6 -- -- 12 -- -- 4 -- -- 7 -- -- 12 -- -- 4 -- -- 5 ns ns ns ns 1 VDD = 3.3 V 10% / 5.0 V 10%, TA = -40 C to TA MAX, unless otherwise specified CL includes device and package capacitances (CPKG < 5 pF). 3 Transition timing of both positive and negative slopes will differ maximum 50% 2 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 75 VDD_HV_IOx/2 Pad Data Input Rising Edge Output Delay Falling Edge Output Delay VOH VOL Pad Output Figure 18. Pad output delay 3.17 3.17.1 AC timing characteristics RESET pin characteristics The MPC5604P implements a dedicated bidirectional RESET pin. VDD VDDMIN VRESET VIH VIL device reset forced by VRESET device start-up phase TPOR Figure 19. Start-up reset requirements MPC5604P Microcontroller Data Sheet, Rev. 8 76 Freescale VRESET hw_rst VDD `1' VIH VIL `0' filtered by hysteresis filtered by lowpass filter WFRST filtered by lowpass filter unknown reset state device under hardware reset WFRST WNFRST Figure 20. Noise filtering on reset signal Table 36. RESET electrical characteristics Symbol C Parameter Value Conditions1 Unit Min Typ Max VIH SR P Input High Level CMOS (Schmitt Trigger) -- 0.65VDD -- VDD+0.4 V VIL SR P Input low Level CMOS (Schmitt Trigger) -- -0.4 -- 0.35VDD V VHYS CC C Input hysteresis CMOS (Schmitt Trigger) -- 0.1VDD -- -- V VOL CC P Output low level Push Pull, IOL = 2mA, VDD = 5.0 V 10%, PAD3V5V = 0 (recommended) -- -- 0.1VDD V Push Pull, IOL = 1mA, VDD = 5.0 V 10%, PAD3V5V = 12 -- -- 0.1VDD Push Pull, IOL = 1mA, VDD = 3.3 V 10%, PAD3V5V = 1 (recommended) -- -- 0.5 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 77 Table 36. RESET electrical characteristics (continued) Symbol C Value Conditions1 Parameter Unit Min Typ Max CL = 25pF, VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 10 CL = 50pF, VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 20 CL = 100pF, VDD = 5.0 V 10%, PAD3V5V = 0 -- -- 40 CL = 25pF, VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 12 CL = 50pF, VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 25 CL = 100pF, VDD = 3.3 V 10%, PAD3V5V = 1 -- -- 40 WFRST SR P RESET input filtered pulse -- -- -- 40 ns WNFRST SR P RESET input not filtered pulse -- 500 -- -- ns -- -- 1 ms VDD = 3.3 V 10%, PAD3V5V = 1 10 -- 150 A VDD = 5.0 V 10%, PAD3V5V = 0 10 -- 150 10 -- 250 ttr CC D Output transition time output pin3 MEDIUM configuration tPOR CC D Maximum delay before Monotonic VDD_HV supply ramp internal reset is released after all VDD_HV reach nominal supply |IWPU| CC P Weak pull-up current absolute value VDD = 5.0 V 10%, PAD3V5V = 14 ns 1 VDD = 3.3 V 10% / 5.0 V 10%, TA = -40 C to TA MAX, unless otherwise specified This is a transient configuration during power-up, up to the end of reset PHASE2 (refer to RGM module section of device reference manual). 3 C includes device and package capacitance (C L PKG < 5 pF). 4 The configuration PAD3V5 = 1 when V = 5 V is only transient configuration during power-up. All pads but RESET DD and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state. 2 3.17.2 IEEE 1149.1 interface timing Table 37. JTAG pin AC electrical characteristics Value No. Symbol C Parameter Conditions Unit Min Max 1 tJCYC CC D TCK cycle time -- 100 -- ns 2 tJDC CC D TCK clock pulse width (measured at VDD_HV_IOx/2) -- 40 60 ns 3 tTCKRISE CC D TCK rise and fall times (40% - 70%) -- -- 3 ns 4 tTMSS, tTDIS CC D TMS, TDI data setup time -- 5 -- ns MPC5604P Microcontroller Data Sheet, Rev. 8 78 Freescale Table 37. JTAG pin AC electrical characteristics (continued) Value No. Symbol C Parameter Conditions Unit Min Max 5 tTMSH, tTDIH CC D TMS, TDI data hold time -- 25 -- ns 6 tTDOV CC D TCK low to TDO data valid -- -- 40 ns 7 tTDOI CC D TCK low to TDO data invalid -- 0 -- ns 8 tTDOHZ CC D TCK low to TDO high impedance -- 40 -- ns 11 tBSDV CC D TCK falling edge to output valid -- -- 50 ns 12 tBSDVZ CC D TCK falling edge to output valid out of high impedance -- -- 50 ns 13 tBSDHZ CC D TCK falling edge to output high impedance -- -- 50 ns 14 tBSDST CC D Boundary scan input valid to TCK rising edge -- 50 -- ns 15 tBSDHT CC D TCK rising edge to boundary scan input invalid -- 50 -- ns TCK 2 3 2 1 3 Figure 21. JTAG test clock input timing MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 79 TCK 4 5 TMS, TDI 6 7 8 TDO Figure 22. JTAG test access port timing MPC5604P Microcontroller Data Sheet, Rev. 8 80 Freescale TCK 11 13 Output Signals 12 Output Signals 14 15 Input Signals Figure 23. JTAG boundary scan timing 3.17.3 Nexus timing Table 38. Nexus debug port timing1 Value No. 1 Symbol tMCYC CC C Parameter D MCKO cycle time valid2 Unit Min Typ Max 32 -- -- ns -- -- 6 ns 2 tMDOV CC D MCKO low to MDO data 3 tMSEOV CC D MCKO low to MSEO data valid2 -- -- 6 ns 4 tEVTOV CC D MCKO low to EVTO data valid2 -- -- 6 ns D TCK cycle time 643 -- -- ns 5 tTCYC CC MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 81 Table 38. Nexus debug port timing1 (continued) Value No. 6 Symbol C Parameter Unit Min Typ Max tNTDIS CC D TDI data setup time 6 -- -- ns tNTMSS CC D TMS data setup time 6 -- -- ns tNTDIH CC D TDI data hold time 10 -- -- ns tNTMSH CC D TMS data hold time 10 -- -- ns 8 tTDOV CC D TCK low to TDO data valid -- -- 35 ns 9 tTDOI CC D TCK low to TDO data invalid 6 -- -- ns 7 1 All Nexus timing relative to MCKO is measured from 50% of MCKO and 50% of the respective signal. MDO, MSEO, and EVTO data is held valid until next MCKO low cycle. 3 Lower frequency is required to be fully compliant to standard. 2 1 MCKO 2 3 4 MDO MSEO EVTO Output Data Valid Figure 24. Nexus output timing TCK EVTI EVTO 5 Figure 25. Nexus event trigger and test clock timings MPC5604P Microcontroller Data Sheet, Rev. 8 82 Freescale TCK 6 7 TMS, TDI 9 8 TDO Figure 26. Nexus TDI, TMS, TDO timing 3.17.4 External interrupt timing (IRQ pin) Table 39. External interrupt timing1 Value No. Symbol C Parameter 1 tIPWL CC D IRQ pulse width low 2 tIPWH CC D IRQ pulse width high 3 tICYC CC D IRQ edge to edge time 2 Conditions Unit Min Max -- 4 -- tCYC -- 4 -- tCYC -- tCYC -- 4+N 3 1 IRQ timing specified at fSYS = 64 MHz and VDD_HV_IOx = 3.0 V to 5.5 V, TA = TL to TH, and CL = 200 pF with SRC = 0b00. 2 Applies when IRQ pins are configured for rising edge or falling edge events, but not both. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 83 3 N = ISR time to clear the flag IRQ 1 2 3 Figure 27. External interrupt timing 3.17.5 DSPI timing Table 40. DSPI timing1 Value No. 1 Symbol tSCK C Parameter CC D DSPI cycle time Conditions Unit Min Max Master (MTFE = 0) 60 -- Slave (MTFE = 0) 60 -- ns 2 tCSC CC D CS to SCK delay -- 16 -- ns 3 tASC CC D After SCK delay -- 26 -- ns 4 tSDC CC D SCK duty cycle -- 5 tA 6 tDIS 0.4 * tSCK 0.6 * tSCK ns CC D Slave access time SS active to SOUT valid -- 30 ns CC D Slave SOUT disable time SS inactive to SOUT high impedance or invalid -- 16 ns 7 tPCSC CC D PCSx to PCSS time -- 13 -- ns 8 tPASC CC D PCSS to PCSx time -- 13 -- ns Master (MTFE = 0) 35 -- ns Slave 4 -- Master (MTFE = 1, CPHA = 0) 35 -- Master (MTFE = 1, CPHA = 1) 35 -- Master (MTFE = 0) -5 -- Slave 4 -- Master (MTFE = 1, CPHA = 0) 11 -- Master (MTFE = 1, CPHA = 1) -5 -- 9 10 tSUI tHI CC D Data setup time for inputs CC D Data hold time for inputs ns MPC5604P Microcontroller Data Sheet, Rev. 8 84 Freescale Table 40. DSPI timing1 (continued) Value No. 11 12 1 Symbol tSUO tHO C Parameter Conditions CC D Data valid (after SCK edge) CC D Data hold time for outputs Unit Min Max Master (MTFE = 0) -- 12 Slave -- 36 Master (MTFE = 1, CPHA = 0) -- 12 Master (MTFE = 1, CPHA = 1) -- 12 Master (MTFE = 0) -2 -- Slave 6 -- Master (MTFE = 1, CPHA = 0) 6 -- Master (MTFE = 1, CPHA = 1) -2 -- ns ns All timing is provided with 50 pF capacitance on output, 1 ns transition time on input signal. 2 3 PCSx 1 4 SCK Output (CPOL=0) 4 SCK Output (CPOL=1) 9 SIN 10 First Data Data 12 SOUT First Data Last Data 11 Data Last Data Note: Numbers shown reference Table 40. Figure 28. DSPI classic SPI timing - Master, CPHA = 0 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 85 PCSx SCK Output (CPOL=0) 10 SCK Output (CPOL=1) 9 Data First Data SIN Last Data 12 SOUT First Data 11 Data Last Data Note: Numbers shown reference Table 40. Figure 29. DSPI classic SPI timing - Master, CPHA = 1 3 2 SS 1 4 SCK Input (CPOL=0) 4 SCK Input (CPOL=1) 5 SOUT First Data 9 SIN 12 11 Data Last Data Data Last Data 6 10 First Data Note: Numbers shown reference Table 40. Figure 30. DSPI classic SPI timing - Slave, CPHA = 0 MPC5604P Microcontroller Data Sheet, Rev. 8 86 Freescale SS SCK Input (CPOL=0) SCK Input (CPOL=1) 11 5 6 12 SOUT First Data 9 SIN Data Last Data Data Last Data 10 First Data Note: Numbers shown reference Table 40. Figure 31. DSPI classic SPI timing - Slave, CPHA = 1 3 PCSx 4 1 2 SCK Output (CPOL=0) 4 SCK Output (CPOL=1) 9 SIN First Data 10 12 SOUT First Data Last Data Data 11 Data Last Data Note: Numbers shown reference Table 40. Figure 32. DSPI modified transfer format timing - Master, CPHA = 0 MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 87 PCSx SCK Output (CPOL=0) SCK Output (CPOL=1) 10 9 SIN First Data Last Data Data 12 First Data SOUT 11 Last Data Data Note: Numbers shown reference Table 40. Figure 33. DSPI modified transfer format timing - Master, CPHA = 1 3 2 SS 1 SCK Input (CPOL=0) 4 4 SCK Input (CPOL=1) SOUT First Data Data First Data 6 Last Data 10 9 SIN 12 11 5 Data Last Data Note: Numbers shown reference Table 40. Figure 34. DSPI modified transfer format timing - Slave, CPHA = 0 MPC5604P Microcontroller Data Sheet, Rev. 8 88 Freescale SS SCK Input (CPOL=0) SCK Input (CPOL=1) 11 5 6 12 First Data SOUT 9 Last Data Data Last Data 10 First Data SIN Data Note: Numbers shown reference Table 40. Figure 35. DSPI modified transfer format timing - Slave, CPHA = 1 7 8 PCSS PCSx Note: Numbers shown reference Table 40. Figure 36. DSPI PCS strobe (PCSS) timing MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 89 4 Package characteristics 4.1 Package mechanical data 4.1.1 144 LQFP mechanical outline drawing L Figure 37. 144 LQFP package mechanical drawing (part 1) MPC5604P Microcontroller Data Sheet, Rev. 8 90 Freescale Figure 38. 144 LQFP package mechanical drawing (part 2) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 91 4.1.2 100 LQFP mechanical outline drawing Figure 39. 100 LQFP package mechanical drawing (part 1) MPC5604P Microcontroller Data Sheet, Rev. 8 92 Freescale Figure 40. 100 LQFP package mechanical drawing (part 2) MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 93 Figure 41. 100 LQFP package mechanical drawing (part 3) MPC5604P Microcontroller Data Sheet, Rev. 8 94 Freescale Table 41. Dimensions Symbol Min Typ Max Min Typ Max A -- -- 1.600 -- -- 0.0630 A1 0.050 -- 0.150 0.0020 -- 0.0059 A2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.170 0.220 0.270 0.0067 0.0087 0.0106 c 0.090 -- 0.200 0.0035 -- 0.0079 D 15.800 16.000 16.200 0.6220 0.6299 0.6378 D1 13.800 14.000 14.200 0.5433 0.5512 0.5591 D3 -- 12.000 -- -- 0.4724 -- E 15.800 16.000 16.200 0.6220 0.6299 0.6378 E1 13.800 14.000 14.200 0.5433 0.5512 0.5591 E3 -- 12.000 -- -- 0.4724 -- e -- 0.500 -- -- 0.0197 -- L 0.450 0.600 0.750 0.0177 0.0236 0.0295 L1 -- 1.000 -- -- 0.0394 -- k 0.0 3.5 7.0 0.0 3.5 7.0 ccc2 1 2 inches1 mm 0.08 0.0031 Values in inches are converted from millimeters (mm) and rounded to four decimal digits. Tolerance MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 95 5 Ordering information Figure 42. Commercial product code structure Example code: M PC 56 0 4 P G F0 M LQ 6 R Qualification Status Power Architecture Core Automotive Platform Core Version Flash Size (core dependent) Product Optional Fields Fab & Mask Revision Temperature spec. Package Code Frequency R = Tape & Reel (blank if Tray) Qualification Status M = MC status S = Automotive qualified P = PC status Automotive Platform 56 = Power Architecture in 90 nm Core Version 0 = e200z0 Flash Size (z0 core) 3 = 384 KB 4 = 512 KB Temperature spec. V = -40 to 105 C M = -40 to 125 C Product P = MPC560xP family Package Code LL = 100 LQFP LQ = 144 LQFP Optional fields E = Data Flash (blank if none) F = FlexRay (blank if none) G = Data Flash + FlexRay Frequency 4 = 40 MHz 6 = 64 MHz MPC5604P Microcontroller Data Sheet, Rev. 8 96 Freescale Appendix A Abbreviations Table A-1 lists abbreviations used in this document. Table A-1. Abbreviations Abbreviation Meaning CMOS Complementary metal-oxide-semiconductor CPHA Clock phase CPOL Clock polarity CS Peripheral chip select DUT Device under test ECC Error code correction EVTO Event out GPIO General purpose input/output MC Modulus counter MCKO Message clock out MCU Microcontroller unit MDO Message data out MSEO Message start/end out MTFE Modified timing format enable NPN NVUSRO Negative-positive-negative Non-volatile user options register PTF Post trimming frequency PWM Pulse width modulation RBW Resolution bandwidth SCK Serial communications clock SOUT Serial data out TCK Test clock input TDI Test data input TDO Test data output TMS Test mode select MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 97 6 Document revision history Table 42 summarizes revisions to this document. Table 42. Revision history Revision Date Substantive changes Rev. 1 Aug 2008 Initial release Rev. 2 Nov 2008 Table 5: TDO and TDI pins (Port pins B[4:5] are single function pins. Table 10, Table 11: Thermal characteristics added. Table 11, Table 12: EMI testing specifications split into separate tables for Normal mode and Airbag mode; data to be added in a later revision. Table 16, Table 17, Table 19, Table 20: Supply current specifications split into separate tables for Normal mode and Airbag mode; data to be added in a later revision. Table 21: * Values for IOL and IOH (in Conditions column) changed. * Max values for VOH_S, VOH_M, VOH_F and VOH_SYM deleted. * VILR max value changed. * IPUR min and max values changed. Table 27: Sensitivity value changed. Table 30: Most values in table changed. Rev. 3 Feb 2009 * * * * * * Description of system requirements, controller characteristics and how controller characteristics are guaranteed updated. Electrical parameters updated. EMI characteristics are now in one table; values have been updated. ESD characteristics are now in one table. Electrical parameters are identified as either system requirements or controller characteristics. Method used to guarantee each controller characteristic is noted in table. AC Timings: 1149.1 (JTAG) Timing, Nexus Timing, External Interrupt Timing, and DSPI Timing sections deleted MPC5604P Microcontroller Data Sheet, Rev. 8 98 Freescale Table 42. Revision history (continued) Revision Rev. 4 Date Substantive changes 24-Jun-2009 Through all document: - Replaced all "RESET_B" occurrences with "RESET" through all document. - AC Timings: 1149.1 (JTAG) Timing, Nexus Timing, External Interrupt Timing, and DSPI Timing sections inserted again. - Electrical parameters updated. - Table 2 - Added row for Data Flash. Table 3 - Added a footnote regarding the decoupling capacitors. Table 5 - Removed the "other function" column. - Rearranged the contents. Table 15 - Updated definition of Condition column. Table 20 - merged in an unique Table the power consumption data related to "Maximum mode" and "Airbag mode". Table 22 - merged in an unique Table the power consumption data related to "Maximum mode" and "Airbag mode". Table 30 - Updated the parameter definition of RCMVAR. - Removed the condition definition of RCMVAR. Table 30 - Added tADC_C and TUE rows. Table 31 - Added tADC_C and TUE rows. - Removed Rsw2. Table 34 - Added. Table 29 - Updated and added footnotes. Section 3.17.1, "RESET pin characteristics - Replaces whole section. Table 38 - Renamed the "Flash (KB)" heading column in "Code Flash / Data Flash (EE) (KB)" - Replaced the value of RAM from 32 to 36KB in the last four rows. MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 99 Table 42. Revision history (continued) Revision Date Substantive changes Rev. 5 06-Oct-2009 - Removed B[4] and B[5] rows from "Pin muxing" table and inserted them on "System pins" table. - Updated package pinout. - Rewrote entirely section "Power Up/dpwn Sequencing" section. - Renamend "VDD_LV_PLL" and "VSS_LV_PLL" supply pins with respectively "VDD_LV_COR3" and "VSS_LV_COR3". - Added explicative figures on "Electrical characteristics" section. - Updated "Thermal characteristics" for 100-pin. - Proposed two different configuration of "voltage regulator. - Inserted Power Up/Down sequence. - Added explicative figures on "DC Electrical characteristics". - Added "I/O pad current specification" section. - Renamed the "Airbag mode" with "Typical mode"and updated the values on "supply current" tables. Rev. 6 12-Feb-2010 Inserted label of Y-axis in the "Independent ADC supply" figure. "Recommended Operating Conditions" tables: Updated the TA value Moved the TJ row to "Absolute Maximum Ratings" table. Rewrite note 1 and 3 Inverted Min a Typ value of CDEC2 on "Voltage Regulator Electrical Characteristics" table. Removed an useless duplicate of "Voltage Regulator Electrical Characteristics" table. Inserted the name of CS into "Input Equivalent Circuit" figure. Removed leakage Ivpp from datasheet. Updated "Supply Current" tables. Added note on "Output pin transition times" table. Updated "Temperature Sensor Electrical Characteristics" table. Updated "16 MHz RC Oscillator Electrical Characteristics" table. Removed the note about the condition from "Flash read access timing" table. Removed the notes that assert the values need to be confirmed before validation. MPC5604P Microcontroller Data Sheet, Rev. 8 100 Freescale Table 42. Revision history (continued) Revision Rev. 7 Date Substantive changes 07-Apr-2011 Formatting and editorial changes throughout Removed all content referencing Junction Temperature Sensor Section 1, "Introduction: changed title (was: Overview); reorganized contents MPC5604P device comparison: * ADC feature: changed "16 channels" to "15-channel"; added footnote to to indicate that four channels are shared between the two ADCs * removed MPC5602P column * indicated that data flash memory is an optional feature * indicated that FlexRay is an optional feature * changed "dual channel" to "selectable single or dual channel support" in FlexRay footnote * updated "eTimer" feature * updated footnote relative to "Digital power supply" feature Updated MPC5604P block diagram Added MPC5604P series block summary Added Section 1.5, "Feature details Section 2.1, "Package pinouts: removed alternate functions from pinout diagrams Supply pins: updated descriptions of power supply pins (1.2 V) System pins: updated table Pin muxing: added rows "B[4]" and "B[5] Section 3.3, "Absolute maximum ratings: added voltage specifications to titles of Figure 4 and Figure 5; in Table 7, changed row "VSS_HV / Digital Ground" to "VSS / Device Ground"; updated symbols Section 3.4, "Recommended operating conditions: added voltage specifications to titles of Figure 6 and Figure 7 Recommended operating conditions (5.0 V), and Recommended operating conditions (3.3 V): changed row "VSS_HV / Digital Ground" to "VSS / Device Ground"; updated symbols Updated Section 3.5.1, "Package thermal characteristics Updated Section 3.6, "Electromagnetic interference (EMI) characteristics Section 3.8.1, "Voltage regulator electrical characteristics: amended titles of Table 15 and Table 17 Voltage regulator electrical characteristics (configuration without resistor on base) and Voltage regulator electrical characteristics (configuration with resistor on base): updated symbol and values for VDD_LV_REGCOR Low voltage monitor electrical characteristics: Updated VMLVDDOK_H max value--was 1.15 V; is 1.145 V Section 3.10, "DC electrical characteristics: reorganized contents Updated Section 3.10.1, "NVUSRO register (includes adding "NVUSRO[OSCILLATOR_MARGIN] field description" table Supply current (5.0 V, NVUSRO[PAD3V5V] = 0): updated symbols MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 101 Table 42. Revision history (continued) Revision Rev. 7 (cont'd) Date Substantive changes 07-Apr-2011 Corrected parameter descriptions in DC electrical characteristics (3.3 V, NVUSRO[PAD3V5V] = 1): * VOL_F--was "Fast, high level output voltage"; is "Fast, low level output voltage" * VOL_SYM--was "Symmetric, high level output voltage"; is "Symmetric, low level output voltage" Supply current (3.3 V, NVUSRO[PAD3V5V] = 1): updated symbols Main oscillator output electrical characteristics (5.0 V, NVUSRO[PAD3V5V] = 0): replaced instances of EXTAL with XTAL Main oscillator output electrical characteristics (3.3 V, NVUSRO[PAD3V5V] = 1): replaced instances of EXTAL with XTAL FMPLL electrical characteristics: replaced "PLLMRFM" with "FMPLL" in table title; updated conditions; removed fsys row; updated fFMPLLOUT min value ADC conversion characteristics: updated symbols; added row tADC_PU Flash memory read access timing: added footnote to "Conditions" column Section 3.16.1, "Pad AC specifications: added Pad output delay diagram In the range of figures "DSPI Classic SPI Timing -- Master, CPHA = 0" to "DSPI PCS Strobe (PCSS) Timing": added note Removed Orderable Part Number Summary table Updated "Commercial product code structure" figure Table A-1: Added abbreviations "DUT", "NPN", and "RBW" MPC5604P Microcontroller Data Sheet, Rev. 8 102 Freescale Table 42. Revision history (continued) Revision Rev. 8 Date Substantive changes 23-May-2012 Section 1.5.4, "Flash memory: Changed "Data flash memory: 32-bit ECC" to "Data flash memory: 64-bit ECC" Figure 42 (Commercial product code structure), replaced "C = 60 MHz, 5 V" and "D = 60 MHz, 3.3 V" with respectively "C = 40 MHz, 5 V" and "D = 40 MHz, 3.3 V" Table 7 (Absolute maximum ratings), updated TVDD parameter, the minimum value to 3.0 V/s and the maximum value to 0.5 V/s Table 5 (Pin muxing), changed the description in the column "I/O direction" from "I/O" to "O" for the following port pins: A[10] with function B[0] A[11] with function A[0] A[11] with function A[2] A[12] with function A[2] A[12] with function B[2] A[13] with function B[2] C[7] with function A[1] C[10] with function A[3] C[15] with function A[1] D[0] with function B[1] D[10] with function A[0] D[11] with function B[0] D[13] with function A[1] D[14] with function B[1] Updated Section 3.8.1, "Voltage regulator electrical characteristics Added Table 25 (I/O consumption) Section 3.10, DC electrical characteristics: deleted references to "oscillator margin" deleted subsection "NVUSRO[OSCILLATOR_MARGIN] field description" Table 19 (DC electrical characteristics (5.0 V, NVUSRO[PAD3V5V] = 0)), added IPU row for RESET pin Table 21 (DC electrical characteristics (3.3 V, NVUSRO[PAD3V5V] = 1)), added IPU row for RESET pin Table 31 (ADC conversion characteristics), added VINAN entry Removed "Order codes" table MPC5604P Microcontroller Data Sheet, Rev. 8 Freescale 103 How to Reach Us: Information in this document is provided solely to enable system and software Home Page: freescale.com implementers to use Freescale products. There are no express or implied copyright Web Support: freescale.com/support information in this document. licenses granted hereunder to design or fabricate any integrated circuits based on the Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: http://www.reg.net/v2/webservices/Freescale/Docs/TermsandConditions.htm Freescale, the Freescale logo, AltiVec, C-5, CodeTest, CodeWarrior, ColdFire, C-Ware, Energy Efficient Solutions logo, Kinetis, mobileGT, PowerQUICC, Processor Expert, QorIQ, Qorivva, StarCore, Symphony, and VortiQa are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Airfast, BeeKit, BeeStack, ColdFire+, CoreNet, Flexis, MagniV, MXC, Platform in a Package, QorIQ Qonverge, QUICC Engine, Ready Play, SafeAssure, SMARTMOS, TurboLink, Vybrid, and Xtrinsic are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. (c) 2008-2012 Freescale, Inc. Document Number: MPC5604P Rev. 8 07/2012