FX604P3 - CML Microcircuits

CML Semiconductor Products

V23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited

D/604/3 November 1996

Provisional Information

1.0 Features

•• 1200/75 bits/sec Full Duplex V23 compatible Modem with:

•• Optional 75bits/sec Back Channel •• Optional Line Equalisation

•• Optional 1200bits/sec Data

Retiming Facility •• -40°C to +85°C Operating

Temperature

•• 3.58MHz Xtal/Clock Rate •• 16-pin SOIC and DIP Packages

•• 3.0 to 5.5V Supply; 1.0mA typ. at 3V

'Zero-Power' Mode; 1µµA typ. •• Conforms to relevant sections of

V23 and ETSI specifications

1.1 Brief Description

The FX604 is a low power CMOS integrated circuit for the reception or transmission of asynchronous

1200bits/sec data in accordance with CCITT V.23 and ETSI specifications. It is also capable of generating the

75bits/sec 'back channel'.

The device incorporates an optional Tx and Rx data retiming function that removes the need for a UART in the

associated µC when operating at 1200bits/sec. The device can disable the back channel or be operated so

only the mark or space tone is produced. An optional line equaliser is incorporated into the receive path, this is

controlled by an external logic level.

The FX604 may be used in a wide range of telephone telemetry systems. With a low voltage requirement of

3.0V it is suitable for both portable terminal and line powered applications. A very low current 'sleep' mode (1µ

A typ.) and operating current of 1mA typ. mean the device is ideal for line powered applications. A 3.58MHz

standard Xtal/Clock rate is required and the device operates from a 3.0 to 5.5V supply. Both SOIC (D4) and

Plastic DIL (P3) 16-pin package types are available.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 2D/604/3

CONTENTS

Section Page

1.0 Features......................................................................................................1

1.1 Brief Description........................................................................................1

1.2 Block Diagram............................................................................................3

1.3 Signal List ..................................................................................................3

1.4 External Components................................................................................5

1.5 General Description...................................................................................5

1.5.1 Xtal Osc and Clock Dividers .........................................................5

1.5.2 Mode Control Logic.......................................................................6

1.5.3 Rx Input Amplifier.........................................................................6

1.5.4 Receive Filter and Equaliser.........................................................6

1.5.5 Energy Detector ...........................................................................7

1.5.6 FSK Demodulator.........................................................................7

1.5.7 FSK Modulator and Transmit Filter ...............................................7

1.5.8 Rx Data Retiming .........................................................................9

1.5.9 Tx Data Retiming........................................................................10

1.6 Application Notes ....................................................................................12

1.6.1 Line Interface..............................................................................12

1.7 Performance Specification ......................................................................13

1.7.1 Electrical Performance ................................................................13

1.7.2 Packaging ..................................................................................16

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 3D/604/3

1.2 Block Diagram

Figure 1 Block Diagram

1.3 Signal List

FX604

D4/P3 Signal Description

Pin No. Name Type

1XTALN O/P The output of the on-chip Xtal oscillator inverter.

2XTAL/CLOCK I/P The input to the on-chip Xtal oscillator inverter.

3M0 I/P A logic level input for setting the mode of the

device. See section 1.5.2.

4M1 I/P A logic level input for setting the mode of the

device. See section 1.5.2.

5RXIN I/P Input to the Rx input amplifier.

6RXFB O/P Output of the Rx input amplifier, and the input to

the Rx filter.

7TXOP O/P The output of the FSK generator.

8VSS Power The negative supply rail (ground).

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 4D/604/3

FX604

D4/P3 Signal Description

Pin No. Name Type

9VBIAS O/P Internally generated bias voltage, held at VDD/2

when the device is not in 'Zero-Power' mode.

Should be decoupled to VSS by a capacitor

mounted close to the device pins.

10 RXEQ I/P A logic level input for enabling/disabling the

equaliser in the receive filter. See section 1.5.4.

11 TXD I/P A logic level input for either the raw input to the

FSK Modulator or data to be re-timed depending

on the state of the M0, M1 and CLK inputs. See

section 1.5.9.

12 CLK I/P A logic level input which may be used to clock

data bits in/out of the FSK Data Retiming block.

13 RXD O/P A logic level output carrying either the raw

output of the FSK Demodulator or re-timed

characters depending on the state of the M0, M1

and CLK inputs. See section 1.5.8.

14 DET O/P A logic level output of the on-chip energy detect

circuit.

15 RDYN O/P "Ready for data transfer" output of the on-chip

data retiming circuit. This open-drain active low

output may be used as an Interrupt

Request/Wake-up input to the associated µC.

An external pull-up resistor should be connected

between this output and VDD.

16 VDD Power The positive supply rail. Levels and thresholds

within the device are proportional to this voltage.

Should be decoupled to VSS by a capacitor

mounted close to the device pins.

Notes: I/P =Input

O/P =Output

This device is capable of detecting and decoding small amplitude signals. To achieve this VDD and VBIAS

decoupling and protecting the receive path from extraneous in-band signals are very important. It is

recommended that the decoupling capacitors are placed so that connections between them and the device

pins are as short as practicable. A ground plane protecting the receive path will help attenuate interfering

signals.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 5D/604/3

1.4 External Components

R1 100kΩC1, C2 18pF

X1 3.579545MHz C3 0.1µF

C4 0.1µF

Resistors ±5%, capacitors ±10% unless otherwise stated.

Figure 2 Recommended External Components for Typical Application

1.5 General Description

1.5.1 Xtal Osc and Clock Dividers

Frequency and timing accuracy of the FX604 is determined by a 3.579545MHz clock present at the

XTAL/CLOCK pin. This may be generated by the on-chip oscillator inverter using the external components C1,

C2 and X1 of Figure 2, or may be supplied from an external source to the XTAL/CLOCK input. If supplied from

an external source, C1, C2 and X1 should not be fitted.

The on-chip oscillator is turned off in the 'Zero-Power' mode.

If the clock is provided by an external source which is not always running, then the 'Zero-Power' mode must be

set when the clock is not available. Failure to observe this rule may cause a significant rise in the supply

current drawn by FX604 as well as generating undefined states of the RXD, DET and RDYN outputs.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 6D/604/3

1.5.2 Mode Control Logic

The FX604's operating mode is determined by the logic levels applied to the M0 and M1 input pins:

M1 M0 Rx Mode Tx Mode Data Retime[1]

0 0 1200bits/sec 75bits/sec Rx

0 1 off 1200bits/sec Tx

1 0 1200bits/sec off Rx

1 1 'Zero-Power' -

[1] If enabled.

In the 'Zero-Power' mode, power is removed from all internal circuitry. When leaving 'Zero-Power' mode there

must be a delay of 20ms before any Tx data is passed to, or Rx data read from, the device to allow the bias

level, filters and oscillator to stabilise. On applying power to the device the mode must be set to 'ZP', i.e.

M0=1, M1=1, until VDD has stabilised.

1.5.3 Rx Input Amplifier

This amplifier is used to adjust the signal received to the correct amplitude for the FSK receiver and Energy

Detect circuits (see section 1.6.1).

1.5.4 Receive Filter and Equaliser

Is used to attenuate out of band noise and interfering signals, especially the locally generated 75bits/sec

transmit tones which might otherwise reach the 1200bits/sec FSK Demodulator and Energy Detector circuits.

This block also includes a switchable equaliser section. When the RXEQ pin is low the overall group delay of

the receive filter is flat over the 1200bits/sec frequency range. If the RXEQ pin is high the receive filter's typical

overall group delay will be as shown in Figure 3.

Figure 3 Rx Equaliser Group Delay (RXEQ = '1') with respect to 1700Hz

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 7D/604/3

1.5.5 Energy Detector

This block operates by measuring the level of the signal at the output of the Receive Filter, and comparing it

against a preset threshold.

The DET output will be set high when the level has exceeded the threshold for sufficient time. Amplitude and

time hysteresis are used to reduce chattering of the DET output in marginal conditions.

Note that this circuit may also respond to non-FSK signals such as speech.

See section 1.7.1 for definitions of Teon and Teoff

Figure 4 FSK Level Detector Operation

1.5.6 FSK Demodulator

This block converts the 1200bits/sec FSK input signal to a logic level received data signal which is output via

the RXD pin as long as the Data Retiming function is not enabled (see section 1.5.8). This output does not

depend on the state of the DET output.

When the Rx 1200bits/sec mode is 'off' or in 'ZP' the DET and RXD pins are held low.

Note that in the absence of a valid FSK signal, the demodulator may falsely interpret speech or other

extraneous signals as data. For this reason it is advised that the RXD pin is read only when data is expected.

1.5.7 FSK Modulator and Transmit Filter

These blocks produce a tone according to the TXD, M0 and M1 inputs as shown in the table below, assuming

data retiming is not being used:

M1 M0 TXD = '0' TXD = '1'

1 1 -

1 0 0Hz[1]

0 0 450Hz 390Hz

0 1 2100Hz 1300Hz

Note: [1] TXOP held at approx VDD/2.

When modulated at the appropriate baud rates, the Transmit Filter and associated external components (see

section 1.6.1) limit the FSK out of band energy sent to the line in accordance with Figures 5a and 5b,

assuming that the signal on the line is at -6dBm or less.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 8D/604/3

Figure 5a Tx limits at 75bits/sec rate

Figure 5b Tx limits at 1200bits/sec rate

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 9D/604/3

1.5.8 Rx Data Retiming

This function may be used when the received data consists of 1200bits/sec asynchronous characters, each

character consisting of one start bit followed by a minimum of 9 formatted bits as shown in the table below.

Data bits Parity bits Stop bits

7 0 >=2

7 1 >=1

8 0 >=1

8 1 >=1

9 0 >=1

The Data Retiming block, when enabled in receive mode, extracts the first 9 bits of each character following

the start bit from the received asynchronous data stream, and presents them to the µC under the control of

strobe pulses applied to the CLK input. The timing of these pulses is not critical and they may easily be

generated by a simple software loop. This facility removes the need for a UART in the µC without incurring an

excessive software overhead.

The receive retiming block consists of two 9-bit shift registers, the input of the first is connected to the output

of the FSK demodulator and the output of the second is connected to the RXD pin. The first register is clocked

by an internally generated signal that stores the 9 received bits following the timing reference of a high to low

transition at the output of the FSK demodulator. When the 9th bit is clocked into the first register these 9 bits

are transferred to the second register, a new stop-start search is initiated and the CLK input is sampled. If the

CLK input is low at this time the RDYN pin is pulled low and the first received bit is output on the RXD pin. The

CLK pin should then be pulsed high 9 times, the first 8 high to low transitions will be used by the device to

clock out the bits in the second register. The RDYN output is cleared the first time the CLK input goes high. At

the end of the 9th pulse the RXD pin will be connected to the FSK demodulator output.

So to use the Data Retiming function, the CLK input should be kept low until the RDYN output goes low; if the

Data Retiming function is not required the CLK input should be kept high at all times.

The only restrictions on the timing of the CLK waveform are those shown in Figure 6a and the need to

complete the transfer of all nine bits into the µC within the time of a complete character at 1200bits/sec.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 10 D/604/3

Td = Internal FX604 delay; max 1µs Tchi = CLK high time; min 1µs Tclo = CLK low time; min 1µs

Figure 6a FSK Operation with Rx Data Retiming

Note that, if enabled, the Data Retiming block may interpret speech or other signals as random characters.

If the Data Retiming facility is not required, the CLK input to the FX604 should be kept high at all times. The

asynchronous data from the FSK Demodulator will then be connected directly to the RXD output pin, and the

RDYN output will not be activated by the FSK signal. This case is illustrated by the example in Figure 6b.

Figure 6b FSK Operation without Rx Data Retiming (CLK always high)

1.5.9 Tx Data Retiming

The Data Retiming block, when enabled in 1200bits/sec transmit mode, requires the controlling µC to load 1

bit at a time into the device by a pulse applied to the CLK input. The timing of this pulse is not critical and it

may easily be generated by a simple software loop. This facility removes the need for a UART in the µC

without incurring an excessive software overhead.

The Tx re-timing circuit consists of two 1-bit registers in series, the input of the first is connected to the TXD

pin and the output of the second feeds the FSK modulator. The second register is clocked by an internally

generated 1200Hz signal and when this occurs the CLK input is sampled. If the CLK input is high the TXD pin

directly controls the FSK modulator, if the CLK input is low the FSK modulator is controlled by the output of the

second register and the RDYN pin is pulled low. The RDYN output is reset by a high level on the CLK input

pin. A low to high change on the CLK input pin will latch the data from the TXD input pin into the first register

ready for transfer to the second register when the internal 1200Hz signal next occurs.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 11 D/604/3

So to use the retiming option the CLK input should be held low until the RDYN output is pulled low. When the

RDYN pin goes low the next data bit should be applied at the TXD input and the CLK input pulled high and

then low within the time limits set out in Figure 6c.

Td = Internal FX604 delay; max 1µs

Tr = RDYN low to CLK going low; max 800µsTs = data set up time; min 1µs

Tchi = CLK high time; min 1µsTh = data hold time; min 1µs

Figure 6c FSK Operation with Tx Data Retiming

To ensure synchronisation between the controlling device and the FX604 when entering Tx retiming mode the

TXD pin must be held at a constant logic level from when the CLK pin is first pulled low to the end of loading in

the second retimed bit. Similarly when exiting Tx retiming mode the TXD pin should be held at the same logic

level as the last retimed bit for at least 2 bit times after the CLK line is pulled high.

If the data retiming facility is not required, the CLK input to the FX604 should be kept high at all times. The

asynchronous data to the FSK modulator will then be connected directly to the TXD input pin. This is

illustrated in Figure 6d and will also be the case when transmitting 75bits/sec data which has no retime option.

Figure 6d FSK Operation without Tx Data Retiming (CLK always high)

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 12 D/604/3

1.6 Application Notes

1.6.1 Line Interface

The signals on the telephone line are not suitable for direct connection to the FX604. A Line Interface circuit is

necessary to:

•Provide high voltage and dc isolation

•Attenuate the Tx signal present at the Rx input

•Provide the low impedance drive necessary for the line

•Filter the Tx and Rx signals

R2 See below C5 22µF (±20%)

R3 See below C6 100pF

R4-R7 100kΩC7 330pF

Resistors ±1%, capacitors ±10% unless otherwise stated.

Figure 7 Line Interface Circuit

Notes:

•The components 'Z' between points B and C should match the line impedance.

•Device A2 must be able to drive 'Z' and the line.

•R2: For optimum results R2 should be set so that the gain is VDD/5.0, i.e. R2 = 100kΩ at VDD =

5.0V, rising to 150kΩ at VDD = 3.3V.

•R3: The levels in dB (relative to a 775mV rms signal) at 'A', 'B' and 'C' in the line interface circuit are:

'A' = 20Log(VDD/5)

'B' = 'A' + 20Log(100kΩ/R3)

'C' = 'B' - 6

VDD 'A' R3 'B' 'C'

3.3V -3.6dB 100kΩ-3.6dB -9.6dB

5.0V 0dB 150kΩ-3.5dB -9.5dB

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 13 D/604/3

1.7 Performance Specification

1.7.1 Electrical Performance

Absolute Maximum Ratings

Exceeding these maximum ratings can result in damage to the device.

Min. Max. Units

Supply (VDD - VSS)-0.3 7.0 V

Voltage on any pin to VSS -0.3 VDD + 0.3 V

Current into or out of VDD and VSS pins -30 +30 mA

Current into or out of any other pin -20 +20 mA

D4 Package Min. Max. Units

Total Allowable Power Dissipation at Tamb = 25°C 800 mW

... Derating 13 mW/°C

Storage Temperature -55 +125 °C

Operating Temperature -40 +85 °C

P3 Package Min. Max. Units

Total Allowable Power Dissipation at Tamb = 25°C 800 mW

... Derating 13 mW/°C

Storage Temperature -55 +125 °C

Operating Temperature -40 +85 °C

Operating Limits

Correct operation of the device outside these limits is not implied.

Notes Min. Max. Units

Supply (VDD - VSS)3.0 5.5 V

Operating Temperature -40 +85 °C

Xtal Frequency 13.575965 3.583125 MHz

Notes: 1. A Xtal frequency of 3.579545MHz ±0.1% is required for correct FSK operation.

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 14 D/604/3

Operating Characteristics

For the following conditions unless otherwise specified:

VDD = 3.0V at Tamb = 25°C and VDD = 3.3V to 5.5V at Tamb = -40 to +85°C,

Xtal Frequency = 3.579545MHz ± 0.1%

0dBV corresponds to 1.0Vrms

0dBm corresponds to 775mVrms into 600Ω.

Notes Min. Typ. Max. Units

DC Parameters

IDD (M0='1', M1='1') 1, 2 -1-µA

IDD (M0 or M1='0') at VDD = 3.0V 1-1.0 1.25 mA

IDD (M0 or M1='0') at VDD= 5.0V 1-1.7 2.5 mA

Logic '1' Input Level 70% - - VDD

Logic '0' Input Level - - 30% VDD

Logic Input Leakage Current (Vin = 0 to VDD),

Excluding XTAL/CLOCK Input -1.0 -+1.0 µA

Output Logic '1' Level (lOH = 360µA) VDD-0.4 - - V

Output Logic '0' Level (lOL = 360µA) - - 0.4 V

RDYN O/P 'off' State Current (Vout = VDD) - - 1.0 µA

FSK Demodulator

Bit Rate 0 1200 1212 Baud

Mark (Logical 1) Frequency 1280 1300 1320 Hz

Space (Logical 0) Frequency 2068 2100 2132 Hz

Valid Input Level Range 3-40.0 --8.0 dBV

Acceptable Twist (Mark Level WRT Space Level) -7.0 -+7.0 dB

Acceptable Signal to Noise Ratio 420.0 - - dB

Level Detector 'On' Threshold Level 3- - -40.0 dBV

Level Detector 'Off' to 'On' Time (Figure 4 Teon) - - 25.0 ms

Level Detector 'On' to 'Off' Time (Figure 4 Teoff) 8.0 - - ms

FSK Retiming

Acceptable Rx Data Rate 1188 1200 1212 Baud

Tx Data Rate 1194 -1206 Baud

FSK Modulator

TXOP Level 5-1.0 0+1.0 dB

Twist (Mark Level WRT Space Level) -2.0 0+2.0 dB

Tx 1200bits/sec (M1='0', M0='1').

Bit Rate 0 1200 1212 Baud

Mark (Logical 1) Frequency 1297 -1303 Hz

Space (Logical 0) Frequency 2097 -2103 Hz

Tx 75bits/sec (M1='0', M0='0').

Bit Rate 0 75 76 Baud

Mark (Logical 1) Frequency 388 -392 Hz

Space (Logical 0) Frequency 448 -452 Hz

V.23 Compatible Modem FX604

 1996 Consumer Microcircuits Limited 15 D/604/3

Notes Min. Typ. Max. Units

Data and Mode Timing

Rx Data Delay (RXIN to RXD) 8-2.55 -ms

Tx Data Delay (TXD to TXOP) 8-0.1 -ms

Mode ZP to Tx or Rx 9- - 20 ms

Mode Tx1200 to Rx1200 9- - 4.0 ms

Mode Rx1200 to Tx1200 9- - 0.2 ms

Input Amplifier

Impedance (RXIN Pin) 610.0 - - MΩ

Voltage Gain 6-500 -V/V

XTAL/CLOCK Input

'High' Pulse Width 7 100 - - ns

'Low' Pulse Width 7 100 - - ns

Notes: 1. At 25°C, not including any current drawn from the FX604 pins by external circuitry other than

X1, C1 and C2.

2. TXD, RXEQ and CLK inputs at VSS, M0 and M1 inputs at VDD.

3. Measured at the Rx Input Amplifier output (pin RXFB) for 1300Hz and VDD= 5.0V.

The internal threshold levels are proportional to VDD. To cater for other supply voltages or

different signal level ranges the voltage gain of the Rx Input Amplifier should be adjusted by

selecting the appropriate external components as described in section 1.6.1

4. Flat noise in 300-3400Hz band.

5. Relative to 775mVrms at VDD= 5.0V for load resistances greater than 40kΩ.

6. Open loop, small signal low frequency measurements.

7. Timing for an external input to the XTAL/CLOCK pin.

8. Assuming data retiming is not enabled.

9. Delay from mode change to reliable data at TXOP or RXD pins.

V.23 Compatible Modem FX604

Handling precautions: This product includes input protection, however, precautions should be taken to prevent

device damage from electro-static discharge. CML does not assume any responsibility for the use of any circuitry

described. No IPR or circuit patent licences are implied. CML reserves the right at any time without notice to

change the said circuitry and this product specification. CML has a policy of testing every product shipped using

calibrated test equipment to ensure compliance with this product specification. Specific testing of all circuit

parameters is not necessarily performed.

CONSUMER MICROCIRCUITS LIMITED

1 WHEATON ROAD Telephone: +44 1376 513833

WITHAM - ESSEX Telefax: +44 1376 518247

CM8 3TD - ENGLAND e-mail: sales@cmlmicro.co.uk

http://www.cmlmicro.co.uk

1.7.2 Packaging

Figure 8 16-pin SOIC (D4) Mechanical Outline: Order as part no. FX604D4

Figure 9 16-pin DIL (P3) Mechanical Outline: Order as part no. FX604P3

CML Product Data

In the process of creating a more global image, the three standard product semiconductor

companies of CML Microsystems Plc (Consumer Microcircuits Limited (UK), MX-COM, Inc

(USA) and CML Microcircuits (Singapore) Pte Ltd) have undergone name changes and, whilst

maintaining their separate new names (CML Microcircuits (UK) Ltd, CML Microcircuits (USA)

Inc and CML Microcircuits (Singapore) Pte Ltd), now operate under the single title CML Micro-

circuits.

These companies are all 100% owned operating companies of the CML Microsystems Plc

Group and these changes are purely changes of name and do not change any underlying legal

entities and hence will have no effect on any agreements or contacts currently in force.

CML Microcircuits Product Prefix Codes

Until the latter part of 1996, the differentiator between products manufactured and sold from

MXCOM, Inc. and Consumer Microcircuits Limited were denoted by the prefixes MX and FX

respectively. These products use the same silicon etc. and today still carry the same prefixes.

In the latter part of 1996, both companies adopted the common prefix: CMX.

This notification is relevant product information to which it is attached.

Company contact information is as below:

CML Microcircuits

(UK)Ltd

COMMUNICATION SEMICONDUCTORS

CML Microcircuits

COMMUNICATION SEMICONDUCTORS

CML Microcircuits

(Singapore)PteLtd

COMMUNICATION SEMICONDUCTORS

CML Microcircuits

(USA) Inc.

COMMUNICATION SEMICONDUCTORS

Oval Park, Langford, Maldon,

Essex, CM9 6WG, England

Tel: +44 (0)1621 875500

Fax: +44 (0)1621 875600

uk.sales@cmlmicro.com

www.cmlmicro.com

4800 Bethania Station Road,

Winston-Salem, NC 27105, USA

Tel: +1 336 744 5050,

0800 638 5577

Fax: +1 336 744 5054

us.sales@cmlmicro.com

www.cmlmicro.com

No 2 Kallang Pudding Road, 09-05/

06 Mactech Industrial Building,

Singapore 349307

Tel: +65 7450426

Fax: +65 7452917

sg.sales@cmlmicro.com

www.cmlmicro.com

D/CML (D)/1 February 2002