Toggles Series DB Electrical Capacity (Resistive Load) C Logic Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: Materials & Finishes Plunger: Bushing: Frame: Case: Movable Contacts: Stationary Contacts: Terminals: Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers General Specifications Tilt Tactiles Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Installation Indicators Touch Mounting Torque: Cap Installation Force: PCB Processing Soldering: Cleaning: Standards & Certifications 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 50 milliohms maximum 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 200,000 operations minimum 100,000 operations minimum Single Pole: 1.96N Double Pole: 2.94N Pretravel .020" (0.5mm); Overtravel .020" (0.5mm); Total Travel .039" (1.0mm) Brass with nickel plating Brass with nickel plating Stainless steel Glass fiber reinforced polyamide Copper with gold plating Phosphor bronze with gold plating Brass with gold plating -10C through +70C (+14F through +158F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 1.47Nm (13.0 lb * in) for double nut; 0.68Nm (6.0 lb * in) for single nut 78.5N (17.65 lbf) maximum downward force on actuator Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile B in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. The DB Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories Light Touch Miniature Pushbuttons C18 www.nkk.com Toggles Series DB Rockers Distinctive Characteristics Both PCB and panel mounting options available. C Programmable Illuminated PB Choice of cap sizes in .315" (8.0mm) and .394" (10.0mm) diameter cap design for simple, snap-on installation. Pushbuttons Light Touch Miniature Pushbuttons High torque bushing prevents rotation and separation from metal frame during installation. Keylocks Stainless steel frame resists corrosion. Rotaries Snap action contacts give smooth actuation, short stroke, light touch, and audible feedback. This mechanism also provides long mechanical life. Slides Molded-in terminals prevent entry of solder flux, dust, and other contaminants. Touch Tilt Tactiles .100" x .100" (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Round terminals for easier through-hole mounting on PC boards. Supplement Accessories Indicators Actual Size www.nkk.com C19 Series DB Toggles Light Touch Miniature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 21 B C PC Terminals Poles & Circuits Programmable Illuminated PB Pushbuttons Rockers DB25 11 SPDT ON (ON) 21 DPDT ON (ON) Threaded Bushing P Straight B Straight with Bracket H Right Angle with Bracket V Vertical with Bracket Smooth Bushing Keylocks ( ) = Momentary Rotaries DESCRIPTION FOR TYPICAL ORDERING EXAMPLE DB2521B with AT443E Cap Slides Yellow .315" (8.0mm) Diameter Cap Tactiles DPDT ON-(ON) Circuit Tilt Smooth Bushing & Straight PC Terminals with Bracket POLES & CIRCUITS Touch Plunger Position ( ) = Momentary Normal Down Note: Terminal numbers are not actually on the switch. Indicators Down Throw & Switch Schematics Pole Model Accessories Normal Connected Terminals SP DB2511 ON (ON) 3-1 3-2 SPDT DP DB2521 ON (ON) 3-1 6-4 3-2 6-5 DPDT Keyway Keyway Supplement 3 (COM) 1 3 (COM) 1 C20 www.nkk.com 2 2 6 4 5 Series DB Toggles Light Touch Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS (14.7) .579 M6 P0.75 (8.0) Dia .315 1 1 (5.08) Typ .200 2 2 (5.08) Typ .200 3 3 Keyway C (1.0) Dia Typ .039 (0.8) Dia Typ .031 (4.6) .181 (7.0) .276 (17.5) .689 (7.2) .283 (8.8) .346 DB2511P with AT443C Double Pole (7.6) .299 (14.7) .579 M6 P0.75 (5.08) .200 1 (5.08) Typ .200 (8.0) Dia .315 4 2 5 3 6 4 1 5 2 6 3 (5.08) Typ .200 Keyway (1.0) Dia Typ .039 (0.8) Dia Typ .031 (0.3) .012 Keylocks (0.3) .012 Straight PC (7.2) .283 (8.8) .346 (17.5) .689 Rotaries (4.6) .181 (12.4) .488 Pushbuttons (7.6) .299 Programmable Illuminated PB (0.3) .012 Straight PC Rockers Single Pole (5.08) .200 DB2521P with AT442A (3.5) .138 1 1 (5.08) Typ .200 (15.24) .600 (8.0) Dia .315 (16.44) .647 (5.08) .200 (0.4) Typ .016 (14.4) .567 2 (7.62) Typ .300 2 (5.08) Typ .200 3 3 Tactiles (6.2) Dia .244 (7.6) .299 Straight PC with Bracket Slides Single Pole Keyway (8.8) .346 (7.0) .276 (6.8) .268 (17.9) .705 (2.54) Typ .100 (1.0) Dia Typ .039 CL (0.7) Typ .028 Tilt (0.8) Dia Typ .031 (4.6) .181 (5.08) .200 (8.0) Dia .315 (16.44) .647 1 (5.08) .200 4 2 5 3 6 Indicators (5.08) Typ .200 (15.24) .600 (0.3) .012 (5.08) .200 (14.4) .567 4 1 5 2 6 3 (7.62) Typ .300 (5.08) Typ .200 Accessories (0.4) Typ .016 (6.2) Dia (3.5) .138 .244 (7.6) .299 Straight PC with Bracket Keyway (7.0) .276 (12.7) .500 (2.54) Typ .100 (0.8) Dia Typ .031 (0.3) .012 (4.6) .181 (8.8) .346 (6.8) .268 (17.9) .705 (0.7) Typ .028 CL (1.0) Dia Typ .039 (5.08) .200 DB2521B with AT443E www.nkk.com C21 Supplement Double Pole Touch DB2511B with AT442C Series DB Toggles Light Touch Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Rockers Right Angle PC with Bracket Single Pole Pushbuttons 2 (5.08) Typ .200 3 3 2 1 (6.5) .256 C (0.7) Typ .028 (5.08) .200 (14.7) .579 (0.4) .016 (0.9) .035 (15.24) .600 (0.3) .012 (8.8) .346 (6.8) .268 (15.24) .600 (3.5) .138 (0.8) Dia .031 (5.08) Typ .200 (2.54) Typ .100 (1.0) Dia Typ .039 CL DB2511H with AT442B Right Angle PC with Bracket Double Pole (6.2) Dia .244 (7.6) .299 4 (12.7) .500 (0.3) .012 Keylocks Programmable Illuminated PB 1 (8.0) Dia .315 (7.0) .276 Rotaries (6.2) Dia .244 (7.6) .299 Keyway (8.0) Dia .315 5 6 (0.3) .012 2 1 (3.5) .138 (0.7) Typ .028 (5.08) .200 (14.4) .567 (0.4) .016 (0.9) .035 (15.24) .600 (6.8) .268 (8.8) .346 6 5 4 3 2 1 (15.24) .600 3 (0.5) (3.5) .020 .138 (0.8) Dia Typ .031 (2.54) .100 (5.08) Typ .200 (2.54) .100 (2.54) Typ .100 (1.0) Dia Typ .039 CL (5.08) Typ .200 DB2521H with AT442A Single Pole Slides Vertical PC with Bracket (6.2) Dia .244 (7.6) .299 Keyway Tactiles (14.7) .579 (0.3) .012 Tilt (3.5) .138 (0.7) Typ .028 (8.0) Dia .315 (5.08) .200 (7.0) .276 2 1 2 (0.3) .012 (8.8) .346 (0.4) .016 (0.9) .035 (15.24) .600 (6.8) .268 (3.5) .138 (2.54) Typ .100 3 3 1 (15.24) .600 (1.0) (0.5) .039 .020 (2.54) Typ .100 (1.0) Dia Typ .039 CL (0.8) Dia .031 (2.54) Typ .100 Touch DB2511V with AT443C Vertical PC with Bracket Double Pole (6.2) Dia .244 Indicators (7.6) .299 6 (14.4) .579 (8.0) Dia .315 (0.3) .012 Accessories Supplement Keyway (0.3) .012 (3.5) .138 3 5 2 4 1 6 3 5 2 4 1 (2.54) Typ .100 (15.24) .600 (3.5) .138 (0.7) Typ .028 (0.3) .012 (5.08) .200 (12.7) .500 (8.8) .346 (6.8) .268 (0.4) .016 (0.9) .035 (15.24) .600 DB2521V with AT443C C22 www.nkk.com (1.0) (0.5) .039 .020 (2.54) Typ .100 (0.8) Dia Typ (5.08) .200 .031 (5.08) .200 (1.0) Dia Typ .039 Series DB Toggles Light Touch Miniature Pushbuttons OPTIONAL CAPS & COLORS E B White F C Red G A (8.0) Dia .315 Yellow Green Blue Cap Material: Polycarbonate Finish: Glossy E Black B White F C Red G Yellow C (10.0) Dia .394 Green Blue Cap Material: Polycarbonate Finish: Glossy HARDWARE Standard Hardware Optional Hardware AT509 Lockwasher AT507M Metric Locking Ring AT501M Metric Knurled Face Nut Material: Brass with Nickel Plating Material: Steel with Zinc/Chromate Material: Steel with Zinc/Chromate Material: Brass with Chrome Plating (6.0) Dia .236 (6.4) Dia (10.2) Dia .252 .402 M6 P0.75 (12.0) Dia .472 (2.0) .079 Slides (8.0) .315 Rotaries AT513M Metric Hexagon Nut M6 P0.75 (10.0) Dia .394 (0.5) .020 (1.7) .067 2 AT513M Metric Hexagon Nuts 1 AT509 Internal Tooth Lockwasher With Standard Hardware Without Bottom Hex Nut Face Nut Optional Hardware: AT507M Metric Locking Ring Note: Cap must be snapped on after the switch is mounted into the panel. (6.35) Dia .250 (6.5) Dia .256 (2.2) Dia .087 (0.6) .024 Maximum Effective Panel Thickness: .118" (3.0mm) Maximum Effective Panel Thickness: .185" (4.7mm) (6.5) .256 Maximum Effective Panel Thickness: .087" (2.2mm) Supplement Lock Nut Locking Ring (Optional) With Standard Hardware & Optional Locking Ring (6.35) Dia .250 (5.6) .220 Lockwasher Tilt PANEL CUTOUTS & THICKNESSES Indicators INSTALLATION/ASSEMBLY (1.7) .067 (0.8) .031 Accessories (1.5) .059 Tactiles (5.5) .217 (9.0) .354 Pushbuttons Black (8.0) .315 Programmable Illuminated PB A Cap Colors Available: (7.6) .299 Keylocks Cap Colors Available: Rockers AT442 .394" (10.0mm) Diameter Snap-on Cap Touch AT443 .315" (8.0mm) Diameter Snap-on Cap www.nkk.com C23