Embedded Power for Business-Critical Continuity Rev. 11.17.08_103 LPQ142 Series of 3 LPQ142 Series 145 Watts Total Power: Input Voltage: # of Outputs: 110 - 145 Watts 85-264 VAC 120-300 VDC Quad Electrical Specifications Special Features * Active power factor correction * IEC EN61000-3-2 compliance * Adjustable outputs on 1, 3 & 4 Remote sense on main output * Single wire current sharing * Power fail and remote inhibit * Built-in EMI filter * Low output ripple * Overvoltage protection * Overload protection * Thermal overload protection * Adjustable floating 4th output * Optional cover (-C suffix) * Optional fan cover (-CF suffix) VDE UL CB CSA CE NEMKO Input range: 85-264 VAC; 120-300 VDC Frequency: 47-67 Hz Inrush current: 38 A max, cold start @ 25C Efficiency: EMI filter: 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Power Factor: 0.99 typical Safety ground leakage current: 1.0 mA @ 50/60 Hz, 264 VAC input Output Maximum power: 80 W convection (60 W with cover -C) 145 W with 30 CFM forced air (100 W with cover -C) Adjustment range: 3.3 - 5.5V on main; -12 - 15V on 3rd output 3.3 - 25 V on 4th output 20 ms @175 W load at nominal line Hold-up time: Safety * * * * * * Input 60950 60950 Certificate and report 60950 Mark (LVD) EN 60950/EMKO-TUE Overload protection: hort circuit protection on all outputs. Case overload protected @ S 110-145% above peak rating Overvoltage protection: Tracks outputs 1, 3 & 4; 10 to 35% Embedded Power for Business-Critical Continuity Rev. 11.17.08_103 LPQ142 Series of 3 Logic Control AC power failure: TL logic signal goes high 100 - 500 msec after V1 output; It goes low T at least 4 msec before loss of regulation Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Remote inhibit: Remote sense: DC - OK: Environmental Specifications Temperature coefficient: 0.4% per C Electromagnetic Designed to meet IE61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 susceptibility: Humidity: Operating; non-condensing 5% to 95% Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational >550,000 hours at full load and 25C ambient conditions MTBF demonstrated: SK1 SK2 SK4 Operating temperature: 0 to 50 C ambient. Derate each output 2.5% per degree from 50 to 70 C (except for -C version). Storage temperature: -40 C to +85 C Vibration: Pin Assignments SK6 PIN 1 Ground PIN 3 Neutral PIN 5 Line PIN 1 +12 V PIN 2 Common PIN 3 -12 V PIN 4 Common PIN 5 +5 V to +25 V (float) PIN 6 Common (float) TB-1 Common TB-2 +5 V PIN 1 N/C PIN 2 DC OK PIN 3 N/C PIN 4 V1 SWP PIN 5 Common PIN 6 +V1 sense PIN 7 Sense common PIN 8 + inhibit PIN 9 - inhibit PIN 10 Power fail Mating Connectors (SK1) AC Input: Ordering Information Minimum Maximum Load with Load Convection Cooling Maximum Load with 30CFM Peak Load 1 Regulation 2 Forced Air Model Number Output Voltage Ripple P/P (PARD)3 LPQ142 5 V (3.3 - 5.5 V) 0A 12 A 25 A 27 A 2% 50 mV 12 V 0A 5A 6A 9A 3% 120 mV -12V (-12 -15 V) 0A 1A 1.5 A 2A 3% <1% 3.3-25 V 0.5 A 1.5 A 4.5 A 5A 3% <50mV or 1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. 4th output adjustable 3.3-25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch Note: -C suffix added to the model number indicates cover option. -CF suffix added to the model number indicates fan cover option. Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK2) Aux DC Output: Molex 09-50-8061 (USA) Molex 09-91-0600 (UK) PINS: 08-58-0111 (SK6) Control Signals: (SK4) Main output: Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Molex BB-19141-0058 Emerson Network Power connector kit #70-841-017, includes al of the above. Embedded Power for Business-Critical Continuity Mechanical Drawing Americas 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 V1 Adj MAIN OUTPUT V4 Adj - Course Europe (UK) V4 Adj - Fine 6 V4V4+ COMM -12V OUT COMM +12V OUT SK2 L 1 N 5 GND 6 1 SK6 -CF option M3 #6-32 (3X) 19.1 29.1 1.5 (38.1) M3 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 10 SK1 Rev. 11.17.08_103 LPQ142 Series of 3 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.powerconversion.com (2X) 6.4 161.5 #6-32 171.5 techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. 4.00 (101.6) (4X) 63.5 Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing (2X) 119.6 (2X) 139.7 7.0 (177.8) M3 (8 places) #6-32 (8 places) Embedded Power Monitoring Outside Plant Power Switching & Controls Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 2 year 6. Weight: 1.63 lb / 0.74 kg Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. (c)2008 Emerson Electric Co.