256Mb: 3V Embedded Parallel NOR Flash Features Micron Parallel NOR Flash Embedded Memory M29DW256G X16 Multiple Bank, Page, Dual Boot 3V Supply Flash Memory Features * VPP/WP# pin for fast program and write - Protects the four outermost parameter blocks * Software protection - Volatile protection - Nonvolatile protection - Password protection * Extended memory block - Programmed or locked at the factory or by the customer - 128 word factory locked and 128 word customer lockable * Common flash interface - 64-bit security code * Low power consumption: standby and automatic mode * 100,000 minimum PROGRAM/ERASE cycles per block * Data retention: 20 years (TYP) * Fortified BGA, TBGA, and TSOP packages * Green packages available - RoHS-compliant - Halogen-free * Automotive certified parts available - Automotive device grade: temperature -40C to +85C (automotive grade certified) * Root part number - M29DW256G * Device code - 227Eh + 223Ch + 2202h * Supply voltage - VCC = 2.7-3.6V (program, erase, read) - VCCQ = 1.65-3.6V (I/O buffers) - VPPH = 9V for fast program (optional) * Asynchronous random/page read - Page size: 8 words - Page access: 25ns, 30ns - Random access: 70ns, 80ns * Fast program commands: 32-word * Enhanced buffered program commands: 256-word * Program time - 16s per byte/word TYP - Chip program time: 10 s with V PPH and 16s without V PPH * Memory organization - Quadruple bank memory array: 32Mb + 96Mb + 96Mb + 32Mb with parameter blocks at top and bottom - Dual operation: program/erase in one bank while reading in any other bank * Program/erase controller - Embedded word program algorithms * Program/erase suspend and resume capability - Read from any block during a PROGRAM SUSPEND operation - Read or program another block during an ERASE SUSPEND operation * Unlock bypass, block erase, chip erase, write to buffer, and enhanced buffer program commands - Fast buffered/batch programming - Fast block/chip erase CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. 256Mb: 3V Embedded Parallel NOR Flash Features Part Numbering Information Available with extended memory block prelocked by Micron. Devices are shipped from the factory with memory content bits erased to 1. For available options, such as packages or high/low protection, or for further information, contact your Micron sales representative. Part numbers can be verified at www.micron.com. Feature and specification comparison by device type is available at www.micron.com/products. Contact the factory for devices not found. Table 1: Part Number Information Part Number Category Category Details Notes Device Type M29 Architecture D = Dual operation Operating Voltage W = VCC = 2.7 to 3.6V Device function 256G = 256Mb (x16) page, dual boot Speed 70 = 70ns 1, 2 7A = 70ns 1, 2 Package NF = 56-pin TSOP, 14mm x 20mm, lead-free, halogen-free, RoHS-compliant ZA = 64-pin TBGA, 10mm x 13mm, lead-free, halogen-free, RoHS-compliant ZS = 64-pin Fortified BGA, 11mm x 13mm, lead-free, halogen-free, RoHS-compliant Temperature Range 1 = 0 to 70C 6 = -40C to +85C Shipping Options E = RoHS-compliant package, standard packing F = RoHS-compliant package, tape and reel packing Notes: 1. 80ns if VCCQ = 1.65V to VCC. 2. Automotive certified -40C to +85C, available only with option 6. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Features Contents Important Notes and Warnings ......................................................................................................................... 7 Description ...................................................................................................................................................... 7 Signals ......................................................................................................................................................... 9 Signal Assignments ......................................................................................................................................... 10 Signal Descriptions ......................................................................................................................................... 12 Memory Organization .................................................................................................................................... 14 Memory Configuration ............................................................................................................................... 14 Block Addresses and Protection Groups ....................................................................................................... 15 Bus Operations ............................................................................................................................................... 19 Read .......................................................................................................................................................... 19 Write .......................................................................................................................................................... 19 Standby and Automatic Standby ................................................................................................................. 19 Output Disable ........................................................................................................................................... 20 Reset .......................................................................................................................................................... 20 Registers ........................................................................................................................................................ 21 Status Register ............................................................................................................................................ 21 Lock Register .............................................................................................................................................. 26 Standard Command Definitions - Address-Data Cycles .................................................................................... 28 READ and AUTO SELECT Operations .............................................................................................................. 31 READ/RESET Command ............................................................................................................................ 31 READ CFI Command .................................................................................................................................. 31 UNLOCK BYPASS READ CFI Command ....................................................................................................... 31 AUTO SELECT Command ........................................................................................................................... 31 Bypass Operations .......................................................................................................................................... 33 UNLOCK BYPASS Command ...................................................................................................................... 33 UNLOCK BYPASS RESET Command ............................................................................................................ 33 Program Operations ....................................................................................................................................... 34 PROGRAM Command ................................................................................................................................ 34 UNLOCK BYPASS PROGRAM Command ..................................................................................................... 34 WRITE TO BUFFER PROGRAM Command .................................................................................................. 34 UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command ....................................................................... 37 WRITE TO BUFFER PROGRAM CONFIRM Command .................................................................................. 37 BUFFERED PROGRAM ABORT AND RESET Command ................................................................................ 37 PROGRAM SUSPEND Command ................................................................................................................ 37 PROGRAM RESUME Command .................................................................................................................. 38 WRITE TO BUFFER PROGRAM SUSPEND Command .................................................................................. 38 WRITE TO BUFFER PROGRAM RESUME Command .................................................................................... 39 ENTER ENHANCED BUFFERED Command ................................................................................................ 39 ENHANCED BUFFERED PROGRAM Command ........................................................................................... 39 ENHANCED BUFFERED PROGRAM ABORT RESET Command .................................................................... 40 EXIT ENHANCED BUFFERED PROGRAM Command ................................................................................... 42 Erase Operations ............................................................................................................................................ 43 CHIP ERASE Command .............................................................................................................................. 43 UNLOCK BYPASS CHIP ERASE Command ................................................................................................... 43 BLOCK ERASE Command ........................................................................................................................... 43 UNLOCK BYPASS BLOCK ERASE Command ................................................................................................ 44 ERASE SUSPEND Command ....................................................................................................................... 44 ERASE RESUME Command ........................................................................................................................ 45 Block Protection Command Definitions - Address-Data Cycles ........................................................................ 46 Protection Operations .................................................................................................................................... 48 CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Features LOCK REGISTER Commands ...................................................................................................................... PASSWORD PROTECTION Commands ....................................................................................................... NONVOLATILE PROTECTION Commands .................................................................................................. NONVOLATILE PROTECTION BIT LOCK BIT Commands ............................................................................ VOLATILE PROTECTION Commands .......................................................................................................... EXTENDED MEMORY BLOCK Commands .................................................................................................. EXIT PROTECTION Command .................................................................................................................... Device Protection ........................................................................................................................................... Hardware Protection .................................................................................................................................. Software Protection .................................................................................................................................... Volatile Protection Mode ............................................................................................................................. Nonvolatile Protection Mode ...................................................................................................................... Password Protection Mode .......................................................................................................................... Dual Operations and Multiple Bank Architecture ............................................................................................. Common Flash Interface ................................................................................................................................ Power-Up and Reset Characteristics ................................................................................................................ Absolute Ratings and Operating Conditions ..................................................................................................... DC Characteristics .......................................................................................................................................... Read AC Characteristics .................................................................................................................................. Write AC Characteristics ................................................................................................................................. Accelerated Program, Data Polling/Toggle AC Characteristics ........................................................................... Program/Erase Characteristics ........................................................................................................................ Package Dimensions ....................................................................................................................................... Revision History ............................................................................................................................................. Rev. B - 5/18 ............................................................................................................................................... Rev. A - 10/12 ............................................................................................................................................. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 4 48 48 49 50 51 51 52 53 53 53 54 54 55 57 59 62 64 66 67 69 73 75 76 79 79 79 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Features List of Figures Figure 1: Logic diagram ................................................................................................................................... 9 Figure 2: 56-Pin TSOP (Top View) .................................................................................................................. 10 Figure 3: 64-Pin Fortified BGA and 64-Pin TBGA ............................................................................................. 11 Figure 4: Block Addresses .............................................................................................................................. 14 Figure 5: Data Polling Flowchart .................................................................................................................... 23 Figure 6: Toggle Bit Flowchart ........................................................................................................................ 24 Figure 7: Status Register Polling Flowchart ..................................................................................................... 25 Figure 8: Lock Register Program Flowchart ..................................................................................................... 27 Figure 9: WRITE TO BUFFER PROGRAM Flowchart ........................................................................................ 36 Figure 10: ENHANCED BUFFERED PROGRAM Flowchart ............................................................................... 41 Figure 11: Program/Erase Nonvolatile Protection Bit Algorithm ...................................................................... 50 Figure 12: Software Protection Scheme .......................................................................................................... 56 Figure 13: Power-Up Timing .......................................................................................................................... 62 Figure 14: Reset AC Timing - No PROGRAM/ERASE Operation in Progress ...................................................... 63 Figure 15: Reset AC Timing During PROGRAM/ERASE Operation .................................................................... 63 Figure 16: AC Measurement Load Circuit ....................................................................................................... 65 Figure 17: AC Measurement I/O Waveform ..................................................................................................... 65 Figure 18: Random Read AC Timing ............................................................................................................... 67 Figure 19: Page Read AC Timing ..................................................................................................................... 68 Figure 20: WE#-Controlled Program AC Timing .............................................................................................. 70 Figure 21: CE#-Controlled Program AC Timing ............................................................................................... 72 Figure 22: Accelerated Program AC Timing ..................................................................................................... 73 Figure 23: Data Polling AC Timing .................................................................................................................. 74 Figure 24: Toggle/Alternative Toggle Bit Polling AC Timing .............................................................................. 74 Figure 25: 56-Pin TSOP - 14mm x 20mm ........................................................................................................ 76 Figure 26: 64-Pin TBGA - 10mm x 13mm ........................................................................................................ 77 Figure 27: 64-Ball Fortified BGA - 11mm x 13mm ........................................................................................... 78 CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Features List of Tables Table 1: Part Number Information ................................................................................................................... 2 Table 2: Signal names ...................................................................................................................................... 9 Table 3: Signal Descriptions ........................................................................................................................... 12 Table 4: Bank architecture ............................................................................................................................. 14 Table 5: Bank A ............................................................................................................................................. 15 Table 6: Bank B ............................................................................................................................................. 15 Table 7: Bank C ............................................................................................................................................. 17 Table 8: Bank D ............................................................................................................................................. 18 Table 9: Bus Operations ................................................................................................................................. 19 Table 10: Status Register Bit Definitions ......................................................................................................... 21 Table 11: Operations and Corresponding Bit Settings ...................................................................................... 22 Table 12: Lock Register Bit Definitions ............................................................................................................ 26 Table 13: Block Protection Status ................................................................................................................... 26 Table 14: Standard Command Definitions - Address-Data Cycles, 16-Bit ......................................................... 28 Table 15: Read Electronic Signature, Auto Select Mode and Programmer Method ............................................. 32 Table 16: Block protection (16-bit mode) ........................................................................................................ 32 Table 17: Block Protection Command Definitions - Address-Data Cycles, 16-Bit .............................................. 46 Table 18: Extended Memory Block Address and Data ...................................................................................... 51 Table 19: V PP/WP# Functions ......................................................................................................................... 53 Table 20: Dual Operations Allowed in Other Banks ......................................................................................... 57 Table 21: Dual Operations Allowed in Same Bank ........................................................................................... 58 Table 22: Query Structure Overview ............................................................................................................... 59 Table 23: CFI Query Identification String ........................................................................................................ 59 Table 24: CFI Query System Interface Information .......................................................................................... 60 Table 25: Device Geometry Definition ............................................................................................................ 60 Table 26: Primary Algorithm-Specific Extended Query Table ........................................................................... 61 Table 27: Security Code Area .......................................................................................................................... 61 Table 28: Power-Up Wait Timing Specifications .............................................................................................. 62 Table 29: Reset AC Specifications ................................................................................................................... 63 Table 30: Absolute Maximum/Minimum Ratings ............................................................................................ 64 Table 31: Operating Conditions ...................................................................................................................... 64 Table 32: Input/Output Capacitance1 ............................................................................................................. 65 Table 33: DC Current Characteristics .............................................................................................................. 66 Table 34: DC Voltage Characteristics .............................................................................................................. 66 Table 35: Read AC Characteristics .................................................................................................................. 67 Table 36: WE#-Controlled Write AC Characteristics ......................................................................................... 69 Table 37: CE#-Controlled Write AC Characteristics ......................................................................................... 71 Table 38: Accelerated Program and Data Polling/Data Toggle AC Characteristics .............................................. 73 Table 39: Program/Erase Characteristics ........................................................................................................ 75 CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Important Notes and Warnings Important Notes and Warnings Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions. This document supersedes and replaces all information supplied prior to the publication hereof. You may not rely on any information set forth in this document if you obtain the product described herein from any unauthorized distributor or other source not authorized by Micron. Automotive Applications. Products are not designed or intended for use in automotive applications unless specifically designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distributor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage resulting directly or indirectly from any use of nonautomotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and conditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron products are not designed or intended for use in automotive applications unless specifically designated by Micron as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to indemnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage resulting from any use of non-automotive-grade products in automotive applications. Critical Applications. Products are not authorized for use in applications in which failure of the Micron component could result, directly or indirectly in death, personal injury, or severe property or environmental damage ("Critical Applications"). Customer must protect against death, personal injury, and severe property and environmental damage by incorporating safety design measures into customer's applications to ensure that failure of the Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron component for any critical application, customer and distributor shall indemnify and hold harmless Micron and its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, or death arising in any way out of such critical application, whether or not Micron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the Micron product. Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems, applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAILURE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included in customer's applications and products to eliminate the risk that personal injury, death, or severe property or environmental damages will result from failure of any semiconductor component. Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort, warranty, breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly authorized representative. Description The M29DW256G is a 256Mb (16Mb x16) non-volatile memory that can be read, erased and reprogrammed. These operations can be performed using a single low voltage (2.7 to 3.6 V) supply. At power-up the memory defaults to its read mode. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Description The M29DW256G features an asymmetrical block architecture, with 8 parameter and 126 main blocks, divided into four banks, A, B, C and D, providing multiple bank operations. While programming or erasing in one bank, read operations are possible in any other bank. Four of the parameter blocks are at the top of the memory address space, and four are at the bottom. Program and erase commands are written to the command interface of the memory. An on-chip program/erase controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a program or erase operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards. Chip Enable, Output Enable and Write Enable signals control the bus operations of the memory. They allow simple connection to most microprocessors, often without additional logic. The device supports asynchronous random read and page read from all blocks of the memory array. The device also features a write to buffer program capability that improves the programming throughput by programming 32 words in one instance. The enhanced buffered program feature is also available to speed up programming throughput, allowing 256 words to be programmed at once. The V PP/WP# signal can be used to enable faster programming of the device. The M29DW256G has one extra 256-word extended block that can be accessed using a dedicated command: 128-Word factory locked and 128-Word customer lockable. The extended block can be protected and so is useful for storing security information. However the protection is irreversible; once protected the protection cannot be undone. The device features different levels of hardware and software block protection to avoid unwanted program or erase (modify): * Hardware protection: V PP/WP# provides hardware protection on four outermost parameter blocks (two at the top and two at the bottom of the address space) * Software protection: Volatile protection, nonvolatile protection, password protection The memory is offered in TSOP56 (14mm x 20mm), TBGA64 (10mm x 13mm, 1mm pitch), and FBGA (11mm x 13mm) packages. The memory is delivered with all the bits erased (set to `1'). CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Description Signals Table 2: Signal names Name Description Direction A[23:0] Address inputs Inputs DQ[15:0] Data inputs/outputs I/O CE# Chip enable Input OE# Output enable Input WE# Write enable Input RST# Reset Input RY/BY# Ready/busy output Output VCCQ Input/output buffer supply voltage Supply VCC Supply voltage Supply VPP/WP# VPP/write protect Supply/Input VSS Ground - NC Not connected - Note: 1. 1 VPP/WP# may be left floating as it is internally connected to a pull-up resistor which enables program/erase operations. Figure 1: Logic diagram VCC VCCQ A[23:0] VPP/WP# DQ[15:0] WE# CE# OE# RY/BY# RST# NC VSS CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Signal Assignments Signal Assignments Figure 2: 56-Pin TSOP (Top View) A23 A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RST# A21 VPP/WP# RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 RFU RFU Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 RFU RFU A16 RFU VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 RFU VCCQ 1. A[23] = A[MAX]. 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Signal Assignments Figure 3: 64-Pin Fortified BGA and 64-Pin TBGA 1 3 2 4 5 7 6 8 8 7 6 5 4 3 2 1 A A RFU A3 A7 RY/BY# WE# A9 A13 RFU RFU A13 A9 WE# RY/BY# A7 A3 RFU B B RFU A4 A17 VPP/WP# RST# A8 A12 A22 A22 A12 A8 RST# VPP/WP# A17 A4 RFU C C RFU A2 A6 A18 A21 A10 A14 A23 A23 A14 A10 A21 A18 A6 A2 RFU D D RFU A1 A5 A20 A19 A11 A15 VCCQ VCCQ A15 A11 A19 A20 A5 A1 RFU E E A0 D0 D2 D5 D7 A16 VSS VSS VCCQ CE# D8 D10 D12 D14 RFU RFU RFU RFU D14 D12 D10 D8 CE# VCCQ RFU OE# D9 D11 VCC D13 D15 RFU RFU D15 D13 VCC D11 D9 OE# RFU RFU VSS D1 D3 D4 D6 VSS RFU RFU VSS D6 D4 D3 D1 VSS RFU RFU A16 D7 D5 D2 D0 A0 RFU F F G G H H Top view - ball side down Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Bottom view - ball side up 1. A[23] = A[MAX]. 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Signal Descriptions Signal Descriptions The signal description table below is a comprehensive list of signals for this device family. All signals listed may not be supported on this device. See Signal Assignments for information specific to this device. Table 3: Signal Descriptions Name Type Description A[MAX:0] Input Address: Selects the cells in the array to access during READ operations. During WRITE operations, they control the commands sent to the command interface of the program/erase controller. DQ[15:0] I/O Data I/O: Outputs the data stored at the selected address during a READ operation. During WRITE operations, they represent the commands sent to the command interface of the internal state machine. During WRITE operations, bits DQ[15:8] are not used. When reading the status register, these bits should be ignored. CE# Input Chip enable: Activates the device, enabling READ and WRITE operations to be performed. When CE# is HIGH, the device goes to standby and data outputs are at HIGH-Z. OE# Input Output enable: Controls the bus READ operation. WE# Input Write enable: Controls the bus WRITE operation of the command interface. VPP/WP# Input VPP/Write Protect: Provides two functions. The VPPH function enables the device to bypass unlock cycles and use an external high voltage power supply to reduce time required for PROGRAM operations. Second, When VPP/WP# is LOW, the four outermost blocks of the address space (two 32KW blocks at the top and two 32KW blocks at the bottom) are protected; PROGRAM and ERASE operations are ignored and the blocks remain protected regardless of the block protection status or the RST# pin state. When VPP/WP# is HIGH, the memory reverts to the previous protection status for those blocks (Refer to Hardware Protection and Bypass Operations for details). RST# Input Reset: Applies a hardware reset to the device, which is achieved by holding RST# LOW for at least tPLPX. After RST# goes HIGH, the device is ready for READ and WRITE operations (after tPHEL or tRHEL, whichever occurs last). See RESET AC Specifications for more details. RY/BY# Output Ready busy: Open-drain output that can be used to identify when the device is performing a PROGRAM or ERASE operation. During PROGRAM or ERASE operations, RY/BY# is LOW, and is High-Z during read mode, auto select mode, and erase suspend mode. After a hardware reset, READ and WRITE operations cannot begin until RY/BY# goes High-Z (see RESET AC Specifications for more details). The use of an open-drain output enables the RY/BY# pins from several devices to be connected to a single pull-up resistor to VCCQ. A low value will then indicate that one or more of the devices is busy. VCC Supply Supply voltage: Provides the power supply for READ, PROGRAM, and ERASE operations. The command interface is disabled when VCC <= VLKO. This prevents WRITE operations from accidentally damaging the data during power-up, power-down, and power surges. If the program/erase controller is programming or erasing during this time, then the operation aborts and the contents being altered will be invalid. A 0.1F capacitor should be connected between VCC and VSS to decouple the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required during PROGRAM and ERASE operations (see DC Characteristics). CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Signal Descriptions Table 3: Signal Descriptions (Continued) Name Type VCCQ Supply I/O supply voltage: Provides the power supply to the I/O pins and enables all outputs to be powered independently from VCC. VSS Supply Ground: All VSS pins must be connected to the system ground. RFU - CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Description Reserved for future use: RFUs should be not connected. 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Memory Organization Memory Organization Memory Configuration The M29DW256G features an asymmetrical block architecture, with 8 parameter and 126 main blocks, divided into four banks providing multiple bank operations. Four parameter blocks are at the top of the memory address space, and four are at the bottom. Table 4: Bank architecture Parameter Blocks Bank Bank Size A B Main Blocks Number of Blocks Block Size Number of Blocks Block Size 32Mb 4 32 Kwords 15 128 Kwords 96Mb -- -- 48 128 Kwords C 96Mb -- -- 48 128 Kwords D 32Mb 4 32 Kwords 15 128 Kwords Figure 4: Block Addresses Address lines A23-A0 800000h 000000h 32 Kwords 128 Kwords 81FFFFh 007FFFh Total of 4 parameter blocks Total of 48 Bank C main blocks DE0000h 018000h 32 Kwords Bank A 128 Kwords DFFFFFh 01FFFFh E00000h 020000h 128 Kwords 128 Kwords E1FFFFh 03FFFFh Total of 15 Total of 15 main blocks main blocks FC0000h 1E0000h 128 Kwords 128 Kwords 1FFFFFh Bank D 200000h FDFFFFh FE0000h 128 Kwords 32 Kwords FE7FFFh 21FFFFh Total of 4 parameter blocks Total of 48 main blocks Bank B FF8000h 7E0000h 32 Kwords 128 Kwords FFFFFFh 7FFFFFh CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Memory Organization Block Addresses and Protection Groups Table 5: Bank A Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 0 Protection Group 32 0000000 - 0007FFF 1 Protection Group 32 0008000 - 000FFFF 2 Protection Group 32 0010000 - 0017FFF 3 Protection Group 32 0018000 - 001FFFF 4 Protection Group 128 0020000 - 003FFFF 5 Protection Group 128 0040000 - 005FFFF 6 Protection Group 128 0060000 - 007FFFF 7 Protection Group 128 0080000 - 009FFFF 8 Protection Group 128 00A0000 - 00BFFFF 9 Protection Group 128 00C0000 - 00DFFFF 10 Protection Group 128 00E0000 - 00FFFFF 11 Protection Group 128 0100000 - 011FFFF 12 Protection Group 128 0120000 - 013FFFF 13 Protection Group 128 0140000 - 015FFFF 14 Protection Group 128 0160000 - 017FFFF 15 Protection Group 128 0180000 - 019FFFF 16 Protection Group 128 01A0000 - 01BFFFF 17 Protection Group 128 01C0000 - 01DFFFF 18 Protection Group 128 01E0000 - 01FFFFF Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 19 Protection Group 128 0200000 - 021FFFF 20 Protection Group 128 0220000 - 023FFFF 21 Protection Group 128 0240000 - 025FFFF 22 Protection Group 128 0260000 - 027FFFF 23 Protection Group 128 0280000 - 029FFFF 24 Protection Group 128 02A0000 - 02BFFFF 25 Protection Group 128 02C0000 - 02DFFFF 26 Protection Group 128 02E0000 - 02FFFFF 27 Protection Group 128 0300000 - 031FFFF 28 Protection Group 128 0320000 - 033FFFF 29 Protection Group 128 0340000 - 035FFFF 30 Protection Group 128 0360000 - 037FFFF 31 Protection Group 128 0380000 - 039FFFF 32 Protection Group 128 03A0000 - 03BFFFF Table 6: Bank B CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Memory Organization Table 6: Bank B (Continued) Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 33 Protection Group 128 03C0000 - 03DFFFF 34 Protection Group 128 03E0000 - 03FFFFF 35 Protection Group 128 0400000 - 041FFFF 36 Protection Group 128 0420000 - 043FFFF 37 Protection Group 128 0440000 - 045FFFF 38 Protection Group 128 0460000 - 047FFFF 39 Protection Group 128 0480000 - 049FFFF 40 Protection Group 128 04A0000 - 04BFFFF 41 Protection Group 128 04C0000 - 04DFFFF 42 Protection Group 128 04E0000 - 04FFFFF 43 Protection Group 128 0500000 - 051FFFF 44 Protection Group 128 0520000 - 053FFFF 45 Protection Group 128 0540000 - 055FFFF 46 Protection Group 128 0560000 - 057FFFF 47 Protection Group 128 0580000 - 059FFFF 48 Protection Group 128 05A0000 - 05BFFFF 49 Protection Group 128 05C0000 - 05DFFFF 50 Protection Group 128 05E0000 - 05FFFFF 51 Protection Group 128 0600000 - 061FFFF 52 Protection Group 128 0620000 - 063FFFF 53 Protection Group 128 0640000 - 065FFFF 54 Protection Group 128 0660000 - 067FFFF 55 Protection Group 128 0680000 - 06FFFFF 56 Protection Group 128 06A0000 - 06BFFFF 57 Protection Group 128 06C0000 - 06DFFFF 58 Protection Group 128 06E0000 - 06FFFFF 59 Protection Group 128 0700000 - 071FFFF 60 Protection Group 128 0720000 - 073FFFF 61 Protection Group 128 0740000 - 075FFFF 62 Protection Group 128 0760000 - 077FFFF 63 Protection Group 128 0780000 - 079FFFF 64 Protection Group 128 07A0000 - 07BFFFF 65 Protection Group 128 07C0000 - 07DFFFF 66 Protection Group 128 07E0000 - 07FFFFF CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Memory Organization Table 7: Bank C Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 67 Protection Group 128 0800000 - 081FFFF 68 Protection Group 128 0820000 - 083FFFF 69 Protection Group 128 0840000 - 085FFFF 70 Protection Group 128 0860000 - 087FFFF 71 Protection Group 128 0880000 - 089FFFF 72 Protection Group 128 08A0000 - 08BFFFF 73 Protection Group 128 08C0000 - 08DFFFF 74 Protection Group 128 08E0000 - 08FFFFF 75 Protection Group 128 0900000 - 091FFFF 76 Protection Group 128 0920000 - 093FFFF 77 Protection Group 128 0940000 - 095FFFF 78 Protection Group 128 0960000 - 097FFFF 79 Protection Group 128 0980000 - 099FFFF 80 Protection Group 128 09A0000 - 09BFFFF 81 Protection Group 128 09C0000 - 09DFFFF 82 Protection Group 128 09E0000 - 09FFFFF 83 Protection Group 128 0A00000 - 0A1FFFF 84 Protection Group 128 0A20000 - 0A3FFFF 85 Protection Group 128 0A40000 - 0A5FFFF 86 Protection Group 128 0A60000 - 0A7FFFF 87 Protection Group 128 0A80000 - 0A9FFFF 88 Protection Group 128 0AA0000 - 0ABFFFF 89 Protection Group 128 0AC0000 - 0ADFFFF 90 Protection Group 128 0AE0000 - 0AFFFFF 91 Protection Group 128 0B00000 - 0B1FFFF 92 Protection Group 128 0B20000 - 0B3FFFF 93 Protection Group 128 0B40000 - 0B5FFFF 94 Protection Group 128 0B60000 - 0B7FFFF 95 Protection Group 128 0B80000 - 0B9FFFF 96 Protection Group 128 0BA0000 - 0BBFFFF 97 Protection Group 128 0BC0000 - 0BDFFFF 98 Protection Group 128 0BE0000 - 0BFFFFF 99 Protection Group 128 0C00000 - 0C1FFFF 100 Protection Group 128 0C20000 - 0C3FFFF 101 Protection Group 128 0C40000 - 0C5FFFF 102 Protection Group 128 0C60000 - 0C7FFFF 103 Protection Group 128 0C80000 - 0CFFFFF 104 Protection Group 128 0CA0000 - 0CBFFFF CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Memory Organization Table 7: Bank C (Continued) Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 105 Protection Group 128 0CC0000 - 0CDFFFF 106 Protection Group 128 0CE0000 - 0CFFFFF 107 Protection Group 128 0D00000 - 0D1FFFF 108 Protection Group 128 0D20000 - 0D3FFFF 109 Protection Group 128 0D40000 - 0D5FFFF 110 Protection Group 128 0D60000 - 0D7FFFF 111 Protection Group 128 0D80000 - 0D9FFFF 112 Protection Group 128 0DA0000 - 0DBFFFF 113 Protection Group 128 0DC0000 - 0DDFFFF 114 Protection Group 128 0DE0000 - 0DFFFFF Block Protection Group Block Size (Kwords) 16-bit address range (in hexadecimal) 115 Protection Group 128 E00000h-E1FFFFh 116 Protection Group 128 E20000h-E3FFFFh 117 Protection Group 128 E40000h-E5FFFFh 118 Protection Group 128 E60000h-E7FFFFh 119 Protection Group 128 E80000h-E9FFFFh 120 Protection Group 128 EA0000h-EBFFFFh 121 Protection Group 128 EC0000h-EDFFFFh 122 Protection Group 128 EE0000h-EFFFFFh 123 Protection Group 128 F00000h-F1FFFFh 124 Protection Group 128 F20000h-F3FFFFh 125 Protection Group 128 F40000h-F5FFFFh 126 Protection Group 128 F60000h-F7FFFFh 127 Protection Group 128 F80000h-F9FFFFh 128 Protection Group 128 FA0000h-FBFFFFh 129 Protection Group 128 FC0000h-FDFFFFh 130 Protection Group 32 FE0000h-FE7FFFh 131 Protection Group 32 FE8000h-FEFFFFh 132 Protection Group 32 FF0000h-FF7FFFh 133 Protection Group 32 FF8000h-FFFFFFh Table 8: Bank D CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Bus Operations Bus Operations Table 9: Bus Operations Notes 1 through 3 apply to entire table Address Inputs Operation Data Inputs/ Outputs CE# OE# WE# RST# VPP/WP# A[MAX], A[0] DQ[15:0] READ L L H H X Cell address Data output WRITE L H L H X4 Command address Data input5 STANDBY H X X H X X High-Z OUTPUT DISABLE L H H H X X High-Z RESET X X X L X X High-Z Notes: 1. Typical glitches of less than 5ns on CE#, WE#, and RST# are ignored by the device and do not affect bus operations. 2. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW. 3. Dual operations are possible with the device multiple bank architecture. While programming or erasing in one bank, read operations are possible in any of the other banks. Write operations are only allowed in one bank at a time. 4. To write the four outermost parameter blocks (first two and the last two) VPP/WP# must be equal to VIH. 5. Data input is required when issuing a command sequence or when performing data polling or block protection. Read Bus READ operations read from the memory cells, registers, or CFI space. To accelerate the READ operation, the memory array can be read in page mode where data is internally read and stored in a page buffer. Page size is 8 words and is addressed by address inputs A[2:0]. A valid bus READ operation involves setting the desired address on the address inputs, taking CE# and OE# LOW, and holding WE# HIGH. The data I/Os will output the value. (See AC Characteristics for details about when the output becomes valid.) Write Bus WRITE operations write to the command interface. A valid bus WRITE operation begins by setting the desired address on the address inputs. The address inputs are latched by the command interface on the falling edge of CE# or WE#, whichever occurs last. The data I/Os are latched by the command interface on the rising edge of CE# or WE#, whichever occurs first. OE# must remain HIGH during the entire bus WRITE operation. (See AC Characteristics for timing requirement details.) Standby and Automatic Standby Driving CE# HIGH in read mode causes the device to enter standby, and data I/Os to be High-Z. To reduce the supply current to the standby supply current (I CC2), CE# must be held within V CC 0.3V. (See DC Characteristics.) CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Bus Operations During PROGRAM or ERASE operations the device will continue to use the program/ erase supply current (ICC3) until the operation completes. Automatic standby allows the memory to achieve low power consumption during read mode. After a READ operation, if CMOS levels (VCC 0.3 V) are used to drive the bus and the bus is inactive for tAVQV + 30ns or more, the memory enters automatic standby where the internal supply current is reduced to the standby supply current, ICC2 (see DC characteristics). The data inputs/outputs still output data if a READ operation is in progress. Depending on load circuits connected with data bus, VCCQ, can have a null consumption when the memory enters automatic standby. Output Disable Data I/Os are High-Z when OE# is HIGH. Reset During reset mode the device is deselected and the outputs are High-Z. The device is in reset mode when RST# is LOW. The power consumption is reduced to the standby level, independently from CE#, OE#, or WE# inputs. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Registers Status Register Table 10: Status Register Bit Definitions Note 1 applies to entire table Bit Name Settings Description Notes DQ7 Data polling 0 or 1, depending on bit operations Monitors whether the program/erase controller has successfully completed its operation, or has responded to an ERASE SUSPEND operation. 2, 3, 4 DQ6 Toggle bit Toggles: 0 to 1; 1 to 0; and so on Monitors whether the program/erase controller has successfully completed its operations, or has responded to an ERASE SUSPEND operation. During a PROGRAM/ERASE operation, DQ6 toggles from 0 to 1, 1 to 0, and so on, with each successive READ operation from any address. 3, 4, 5 DQ5 Error bit 0 = Success 1 = Failure Identifies errors detected by the program/erase controller. DQ5 is set to 1 when a PROGRAM, BLOCK ERASE, or CHIP ERASE operation fails to write the correct data to the memory. 4, 6 DQ3 Erase timer bit 0 = Erase not in progress 1 = Erase in progress Identifies the start of program/erase controller operation during a BLOCK ERASE command. Before the program/erase controller starts, this bit set to 0, and additional blocks to be erased can be written to the command interface. 4 DQ2 Alternative toggle bit Toggles: 0 to 1; 1 to 0; and so on Monitors the program/erase controller during ERASE operations. During CHIP ERASE, BLOCK ERASE, and ERASE SUSPEND operations, DQ2 toggles from 0 to 1, 1 to 0, and so on, with each successive READ operation from addresses within the blocks being erased. 3, 4 DQ1 Buffered program abort bit 1 = Abort Indicates a BUFFER PROGRAM operation abort. The BUFFERED PROGRAM ABORT and RESET command must be issued to return the device to read mode (see WRITE TO BUFFER PROGRAM command). Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. The status register can be read during PROGRAM, ERASE, or ERASE SUSPEND operations; the READ operation outputs data on DQ[7:0]. 2. For a PROGRAM operation in progress, DQ7 outputs the complement of the bit being programmed. For a READ operation from the address previously programmed successfully, DQ7 outputs existing DQ7 data. For a READ operation from addresses with blocks to be erased while an ERASE SUSPEND operation is in progress, DQ7 outputs 0; upon successful completion of the ERASE SUSPEND operation, DQ7 outputs 1. For an ERASE operation in progress, DQ7 outputs 0; upon either operation's successful completion, DQ7 outputs 1. 3. After successful completion of a PROGRAM or ERASE operation, the device returns to read mode. 4. During erase suspend mode, READ operations to addresses within blocks not being erased output memory array data as if in read mode. A protected block is treated the same as a block not being erased. See the Toggle Flowchart for more information. 5. During erase suspend mode, DQ6 toggles when addressing a cell within a block being erased. The toggling stops when the program/erase controller has suspended the ERASE operation. See the Toggle Flowchart for more information. 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers 6. When DQ5 is set to 1, a READ/RESET command must be issued before any subsequent command. Table 11: Operations and Corresponding Bit Settings Note 1 applies to entire table Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 DQ1 RY/BY# Notes PROGRAM Any address DQ7# Toggle 0 - No toggle 0 0 2 PROGRAM during ERASE SUSPEND Any address DQ7# Toggle 0 - - - 0 ENHANCED BUFFERED PROGRAM Entry Any address - Toggle 0 - - - 0 BUFFERED PROGRAM ABORT Any address DQ7# Toggle 0 - - 1 0 PROGRAM error Any address DQ7# Toggle 1 - - - High-Z CHIP ERASE Any address 0 Toggle 0 1 Toggle - 0 BLOCK ERASE before time-out BLOCK ERASE ERASE SUSPEND Erasing block 0 Toggle 0 0 Toggle - 0 Non-erasing block 0 Toggle 0 0 No toggle - 0 Erasing block 0 Toggle 0 1 Toggle - 0 Non-erasing block 0 Toggle 0 1 No toggle - 0 1 No toggle 0 - Toggle Erasing block - High-Z Outputs memory array data as if in read mode - High-Z Good block address 0 Toggle 1 1 No toggle - High-Z Faulty block address 0 Toggle 1 1 Toggle - High-Z Non-erasing block BLOCK ERASE error Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 2 1. Unspecified data bits should be ignored. 2. DQ7# for buffer program is related to the last address location loaded. 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Figure 5: Data Polling Flowchart Start Read DQ7, DQ5, and DQ1 at valid address1 Yes DQ7 = Data No No DQ1 = 13 No DQ5 = 12 Yes Yes Read DQ7 at valid address DQ7 = Data Yes No Failure 4 Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Success 1. Valid address is the address being programmed or an address within the block being erased. 2. Failure results: DQ5 = 1 indicates an operation error; DQ1 = 1 indicates a WRITE TO BUFFER PROGRAM ABORT operation. 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Figure 6: Toggle Bit Flowchart Start Read DQ6 at valid address Read DQ6, DQ5, and DQ1 at valid address DQ6 = Toggle Yes No DQ1 = 1 No No DQ5 = 1 Yes Yes Read DQ6 (twice) at valid address DQ6 = Toggle No Yes Failure1 Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Success 1. Failure results: DQ5 = 1 indicates an operation error; DQ1 = 1 indicates a WRITE TO BUFFER PROGRAM ABORT operation. 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Figure 7: Status Register Polling Flowchart Start Read 1 DQ7 = Valid data Yes Read 2 Read 3 PROGRAM operation Yes Read 3 correct data? Yes No No No DQ5 = 1 Yes PROGRAM operation failure Read 2 No DQ6 = Toggling Yes Read2.DQ6 = Read3.DQ6 Read 3 Device error No DQ6 = Toggling Yes Read1.DQ6 = Read2.DQ6 DQ2 = Toggling Timeout failure Read2.DQ2 = Read3.DQ2 No No Yes DQ1 = 1 Erase/suspend mode No ERASE operation complete Device busy: Repolling WRITE TO BUFFER PROGRAM Yes Yes PROGRAM operation complete WRITE TO BUFFER PROGRAM abort No Device busy: Repolling CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Lock Register Table 12: Lock Register Bit Definitions Note 1 applies to entire table Bit Name Settings DQ[15:5] RFU Description Notes - Reserved for future use 2 Sets default values for volatile block protection; when this bit is programmed, blocks are protected at power-up. DQ4 Volatile lock boot bit Programmable DQ3 RFU - Reserved for future use 2 DQ2 Password protection mode lock bit 0 = Password protection mode enabled 1 = Password protection mode disabled (Default) Places the device permanently in password protection mode. 3 DQ1 Nonvolatile protection mode lock bit 0 = Nonvolatile protection mode enabled with password protection mode permanently disabled 1 = Nonvolatile protection mode enabled (Default) Places the device in nonvolatile protection mode with password protection mode permanently disabled. When shipped from the factory, the device will operate in nonvolatile protection mode, and the memory blocks are unprotected. 3 DQ0 Extended memory block protection bit 0 = Protected 1 = Unprotected (Default) If the device is shipped with the extended memory block unlocked, the block can be protected by setting this bit to 0. The extended memory block protection status can be read in auto select mode by issuing an AUTO SELECT command. It can also be read by applying VID to A9. Notes: 1. The lock register is a 16-bit, one-time programmable register. 2. DQ[15:5] and DQ[3] are reserved and are set to a default value of 1. During programming, they must be held to 1. 3. The password protection mode lock bit and nonvolatile protection mode lock bit cannot both be programmed to 0. Any attempt to program one while the other is programmed causes the operation to abort, and the device returns to read mode. The device is shipped from the factory with the default setting. Table 13: Block Protection Status Nonvolatile Nonvolatile Volatile Protection Bit Protection Protection Lock Bit1 Bit2 Bit3 Block Protection Status Block Protection Status 0 0 X 01h Block protected by nonvolatile protection bit; nonvolatile protection bit unchangeable. 0 1 1 00h Block unprotected; nonvolatile protection bit unchangeable. 0 1 0 01h Block protected by volatile protection bit; nonvolatile protection bit unchangeable. 1 0 X 01h Block protected by nonvolatile protection bit; nonvolatile protection bit changeable. 1 1 0 01h Block protected by volatile protection bit; nonvolatile protection bit changeable. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Registers Table 13: Block Protection Status (Continued) Nonvolatile Nonvolatile Volatile Protection Bit Protection Protection Lock Bit1 Bit2 Bit3 1 1 Notes: Block Protection Status 1 00h Block Protection Status Block unprotected; nonvolatile protection bit changeable. 1. Nonvolatile protection bit lock bit: when cleared to 1, all nonvolatile protection bits are unlocked; when set to 0, all nonvolatile protection bits are locked. 2. Block nonvolatile protection bit: when cleared to 1, the block is unprotected; when set to 0, the block is protected. 3. Block volatile protection bit: when cleared to 1, the block is unprotected; when set to 0, the block is protected. Figure 8: Lock Register Program Flowchart Start Enter LOCK REGISTER command set Address/data (unlock) cycle 1 Address/data (unlock) cycle 2 Address/data cycle 3 PROGRAM LOCK REGISTER Address/data cycle 1 Address/data cycle 2 Polling algorithm Yes Done? No DQ5 = 1 No Yes Success: EXIT PROTECTION command set (Returns to device read mode) Address/data cycle 1 Address/data cycle 2 Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Failure: READ/RESET (Returns device to read mode) 1. Each lock register bit can be programmed only once. 2. See the Block Protection Command Definitions table for address-data cycle details. 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Standard Command Definitions - Address-Data Cycles Standard Command Definitions - Address-Data Cycles Table 14: Standard Command Definitions - Address-Data Cycles, 16-Bit Note 1 applies to entire table Address and Data Cycles Command and Code/Subcode Bus Size 1st A 2nd D 3rd 4th A D A D 2AA 55 X F0 A 5th D A 6th D A D Notes READ and AUTO SELECT Operations READ/RESET (F0h) x16 X F0 555 AA READ CFI (98h) x16 BKA 555 98 UNLOCK BYPASS READ CFI (98h) x16 BKA 98 AUTO SELECT (90h) x16 555 AA 2AA 55 BKA 555 90 UNLOCK BYPASS (20h) x16 555 AA 2AA 55 555 20 UNLOCK BYPASS RESET (90h/00h) x16 X 90 X 00 PROGRAM (A0h) x16 555 AA 2AA 55 555 A0 UNLOCK BYPASS PROGRAM (A0h) x16 X A0 PA PD WRITE TO BUFFER PROGRAM (25h) x16 555 AA 2AA 55 BAd 25 UNLOCK BYPASS WRITE TO BUFFER PROGRAM (25h) x16 BAd 25 BAd N PA PD WRITE TO BUFFER PROGRAM CONFIRM (29h) x16 BAd 29 BUFFERED PROGRAM ABORT and RESET (F0h) x16 555 AA 2AA 55 555 F0 ENTER ENHANCED BUFFERED PROGRAM COMMAND SET (38h) x16 555 AA 2AA 55 555 38 9 ENHANCED BUFFERED PROGRAM (33h) x16 BAd 33 BAd (00) Data BAd (01) Data 9 Note Note 2 2 2, 3, 4 BYPASS Operations PROGRAM Operations CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN PA PD 5 28 BAd N PA PD 6, 7, 8 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Standard Command Definitions - Address-Data Cycles Table 14: Standard Command Definitions - Address-Data Cycles, 16-Bit (Continued) Note 1 applies to entire table Address and Data Cycles Command and Code/Subcode Bus Size ENHANCED BUFFERED PROGRAM CONFIRM (29h) 1st 2nd A D x16 BAd (00) 29 EXIT ENHANCED BUFFERED PROGRAM COMMAND SET (90h) x16 X 90 PROGRAM SUSPEND (B0h) x16 BKA B0 PROGRAM RESUME (30h) x16 BKA 30 WRITE TO BUFFER PROGRAM SUSPEND (B0h) x16 BAd B0 WRITE TO BUFFER PROGRAM RESUME (30h) x16 BAd 30 CHIP ERASE (80/10h) x16 555 UNLOCK BYPASS CHIP ERASE (80/10h) x16 BLOCK ERASE (80/30h) 3rd A D X 00 AA 2AA 55 X 80 X 10 x16 555 AA 2AA 55 UNLOCK BYPASS BLOCK ERASE (80/30h) x16 X 80 BAd 30 ERASE SUSPEND (B0h) x16 BKA B0 ERASE RESUME (30h) x16 BKA 30 4th 5th 6th A D A D A D A D 555 80 555 AA 2AA 55 555 10 Notes ERASE Operations Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 5 555 80 555 AA 2AA 55 BAd 30 10 5 1. A = Address; D = Data; X = "Don't Care;" BKA = Bank address; BAd = Any address in the block; N = Number of bytes to be programmed; PA = Program address; PD = Program data; Gray shading = Not applicable. All values in the table are hexadecimal. Some commands require both a command code and subcode. 2. These cells represent READ cycles (versus WRITE cycles for the others). 3. AUTO SELECT enables the device to read the manufacturer code, device code, block protection status, and extended memory block protection indicator. 4. AUTO SELECT addresses and data are specified in the Electronic Signature table and the Extended Memory Block Protection table. 5. For any UNLOCK BYPASS ERASE/PROGRAM command, the first two UNLOCK cycles are unnecessary. 6. BAd must be the same as the address loaded during the WRITE TO BUFFER PROGRAM 3rd and 4th cycles. 7. WRITE TO BUFFER PROGRAM operation: maximum cycles 36 (x16). UNLOCK BYPASS WRITE TO BUFFER PROGRAM operation: maximum cycles = 34 (x16). WRITE TO BUFFER 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Standard Command Definitions - Address-Data Cycles PROGRAM operation: N + 1 = bytes to be programmed; maximum buffer size = 32 words (x16). 8. For x16, A[MAX:5] address pins should remain unchanged while A[4:0] pins are used to select a word within the N + 1 word page. 9. The following is content for address-data cycles 256 through 258: BAd (FE) - Data; BAd (FF) - Data; BAd (00) - 29. 10. BLOCK ERASE address cycles can extend beyond six address-data cycles, depending on the number of blocks to erase. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash READ and AUTO SELECT Operations READ and AUTO SELECT Operations READ/RESET Command The device is in read mode after a reset or power-up. The READ/RESET (F0h) command returns the device to read mode and resets the errors in the status register. One or three bus WRITE operations can be used to issue the READ/RESET command. To return the device to read mode, this command can be issued between bus WRITE cycles before the start of a PROGRAM or ERASE operation. If the READ/RESET command is issued during the timeout of a BLOCK ERASE operation, the device requires up to 10s to abort, during which time no valid data can be read. The READ/RESET command will not abort a PROGRAM operation if executed while the device is in program suspend, or an ERASE operation if executed while the device is in erase suspend. READ CFI Command The READ CFI (98h) command puts the device in read CFI mode and is only valid when the device is in read array or auto select mode. One bus WRITE cycle is required to issue the command. Once in read CFI mode, bus READ operations will output data from the CFI memory area (Refer to the Common Flash Interface for details). A READ/RESET command must be issued to return the device to the previous mode (read array or auto select ). A second READ/RESET command is required to put the device in read array mode from auto select mode. UNLOCK BYPASS READ CFI Command The UNLOCK BYPASS READ CFI (98h) command enables the device to read the CFI when the device is in the unlock bypass mode. Once in read CFI mode, bus READ operations will output data from the CFI memory area (Refer to the Common Flash Interface for details). A READ/RESET command must be issued to return the device to the previous mode (read array or auto select ). A second READ/RESET command is required to put the device in read array mode from auto select mode. AUTO SELECT Command At power-up or after a hardware reset, the device is in read mode. It can then be put in auto select mode by issuing an AUTO SELECT (90h) command. Auto select mode enables the following device information to be read: * Electronic signature, which includes manufacturer and device code information as shown in the Electronic Signature tables. * Block protection, which includes the block protection status and extended memory block protection indicator, as shown in the Block Protection tables. For example, auto select mode can be used by the programming equipment to automatically match a device with the application code to be programmed. Electronic signature or block protection information is read by executing a READ operation with control signals and addresses set, as shown in the Read Electronic Signature CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash READ and AUTO SELECT Operations tables or the Block Protection tables, respectively. If the block is protected, then 01h is output on data input/outputs DQ0-DQ7, otherwise 00h is output. Three consecutive bus WRITE operations are required to issue an AUTO SELECT command. The device remains in auto select mode until a READ/RESET or READ CFI command is issued. The device cannot enter auto select mode when a PROGRAM or ERASE operation is in progress (RY/BY# LOW) unless the respective operation is suspended by a PROGRAM SUSPEND or an ERASE SUSPEND command. Auto select mode is exited by performing a reset. The device returns to read mode unless it entered auto select mode after an ERASE SUSPEND or PROGRAM SUSPEND command, in which case it returns to erase or program suspend mode. Table 15: Read Electronic Signature, Auto Select Mode and Programmer Method Address inputs Read cycle1 E# G# W# Manufacturer code VIL VIL VIH A[23:10] A[9:8] A[7:5] Data IO A4 A3 A2 A1 A0 DQ[15:0] X VIL VIL VIL VIL 0020h X VIL VIL VIL VIH 227Eh Device code (cycle 2) VIH VIH VIH VIL 223Ch Device code (cycle 3) VIH VIH VIH VIH 2202h X X VIL Device code (cycle 1) Note: 1. X = VIL or VIH. Table 16: Block protection (16-bit mode) Address inputs VPP/ E# G# W# RST# WP# A[23:12] A[11:10] A9 A8 A7 A6 A[5:4] A[3:2] A1 A0 Data IO Bits Value Operation: Verify extended memory block indicator bit VIL VIL VIH VIH VIH BKA X X X VIL VIL VIL VIL VIH VIH DQ[15:8] 0 DQ7 1 = factory locked DQ6 1 = customer locked, 0 = customer lockable DQ5 1 = reserved, 0 = standard DQ[4:3] 00 = WP# protects 4 outermost blocks, 11 = No WP# protection (hardware write protection) DQ[2:0] 0 Operation: Verify block protection status VIL VIL VIH VIH VIH BAd Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN X X X VIL VIL VIL VIL VIH VIL 0000h (unprotected) 0001h (protected) 1. X = VIL or VIH. BAd any address in the block, BKA bank address. 32 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Bypass Operations Bypass Operations UNLOCK BYPASS Command The UNLOCK BYPASS (20h) command is used to place the device in unlock bypass mode. Three bus WRITE operations are required to issue the UNLOCK BYPASS command. When the device enters unlock bypass mode, the two initial UNLOCK cycles required for a standard PROGRAM or ERASE operation are not needed, thus enabling faster total program or erase time. The UNLOCK BYPASS command is used in conjunction with UNLOCK BYPASS PROGRAM or UNLOCK BYPASS ERASE commands to program or erase the device faster than with standard PROGRAM or ERASE commands. When the cycle time to the device is long, considerable time savings can be gained by using these commands. When in unlock bypass mode, only the following commands are valid: * The UNLOCK BYPASS PROGRAM command can be issued to program addresses within the device. * The UNLOCK BYPASS BLOCK ERASE command can be issued to erase one or more memory blocks. * The UNLOCK BYPASS CHIP ERASE command can be issued to erase the whole memory array. * The UNLOCK BYPASS WRITE TO BUFFER PROGRAM command can be issued to speed up the programming operation. * The UNLOCK BYPASS CFI command can be issued to read the CFI when the memory is in unlock bypass mode * The UNLOCK BYPASS RESET command can be issued to return the device to read mode. In unlock bypass mode, the device can be read as if in read mode. In addition to the UNLOCK BYPASS command, when V PP/WP# is raised to V PPH, the device automatically enters unlock bypass mode. When V PP/WP# returns to V IH or V IL, the device is no longer in unlock bypass mode and normal operation resumes. The transitions from V IH to V PPH and from V PPH to V IH must be slower than tVHVPP (see the Accelerated Program, Data Polling/Toggle AC Characteristics). Note: Micron recommends the user enter and exit unlock bypass mode using ENTER UNLOCK BYPASS and UNLOCK BYPASS RESET commands rather than raising V PP/WP# to V PPH. V PP/WP# should never be raised to V PPH from any mode except read mode; otherwise, the device may be left in an indeterminate state. UNLOCK BYPASS RESET Command The UNLOCK BYPASS RESET (90/00h) command is used to return to read/reset mode from unlock bypass mode. Two bus WRITE operations are required to issue the UNLOCK BYPASS RESET command. The READ/RESET command does not exit from unlock bypass mode. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations Program Operations PROGRAM Command The PROGRAM (A0h) command can be used to program a value to one address in the memory array. The command requires four bus WRITE operations, and the final WRITE operation latches the address and data in the internal state machine and starts the program/erase controller. Programming can be suspended and then resumed by issuing a PROGRAM SUSPEND command and a PROGRAM RESUME command, respectively. If the address falls in a protected block, the PROGRAM command is ignored, and the data remains unchanged. The status register is not read, and no error condition is given. After programming has started, bus READ operations output the status register content. A bus READ operation from a bank different from the one whose blocks are being programmed will output the memory array content. After the PROGRAM operation has completed, the device returns to read mode, unless an error has occurred. When an error occurs, bus READ operations to the device continue to output the status register. A READ/RESET command must be issued to reset the error condition and return the device to read mode. The PROGRAM command cannot change a bit set to 0 back to 1, and an attempt to do so is masked during a PROGRAM operation. Instead, an ERASE command must be used to set all bits in one memory block or in the entire memory from 0 to 1. The PROGRAM operation is aborted by performing a reset or by powering-down the device. In this case, data integrity cannot be ensured, and it is recommended that the aborted data be reprogrammed. UNLOCK BYPASS PROGRAM Command When the device is in unlock bypass mode, the UNLOCK BYPASS PROGRAM (A0h) command can be used to program one address in the memory array. The command requires two bus WRITE operations instead of four required by a standard PROGRAM command; the final WRITE operation latches the address and data and starts the program/erase controller (The standard PROGRAM command requires four bus WRITE operations). This UNLOCK BYPASS PROGRAM operation behaves identically to the PROGRAM operation. The operation cannot be aborted. A bus READ operation from the memory outputs the status register. A bus READ operation from a bank different from the one whose blocks are being programmed will output the memory array content. WRITE TO BUFFER PROGRAM Command The WRITE TO BUFFER PROGRAM (25h) command makes use of the 32-word program buffer to speed up programming. A maximum of 32 words can be loaded into the program buffer; each write buffer has the same A[23:5]. The WRITE TO BUFFER PROGRAM command dramatically reduces system programming time compared to the standard non-buffered PROGRAM command. When issuing a WRITE TO BUFFER PROGRAM command, V PP/WP# can be either held HIGH or raised to V PPH. Also, it can be held LOW if the block is not one of the four outer- CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations most blocks, depending on the part number. The following successive steps are required to issue the WRITE TO BUFFER PROGRAM command: First, two UNLOCK cycles are issued. Next, a third bus WRITE cycle sets up the WRITE TO BUFFER PROGRAM command. The set-up code can be addressed to any location within the targeted block. Then, a fourth bus WRITE cycle sets up the number of words to be programmed. Value n is written to the same block address, where n + 1 is the number of words to be programmed. Value n + 1 must not exceed the size of the program buffer, or the operation will abort. A fifth cycle loads the first address and data to be programmed. Last, n bus WRITE cycles load the address and data for each word into the program buffer. Addresses must lie within the range from the start address +1 to the start address + (n - 1). Optimum programming performance and lower power usage are achieved by aligning the starting address at the beginning of a 32-word boundary; otherwise, programming time doubles. All addresses used in the operation must lie within the same page. To program the content of the program buffer, this command must be followed by a WRITE TO BUFFER PROGRAM CONFIRM command. If an address is written several times during a WRITE TO BUFFER PROGRAM operation, the address/data counter will be decremented at each data load operation, and the data will be programmed to the last word loaded into the buffer. Invalid address combinations or the incorrect sequence of bus WRITE cycles will abort the WRITE TO BUFFER PROGRAM command. The status register bits DQ1, DQ5, DQ6, DQ7 can be used to monitor the device status during a WRITE TO BUFFER PROGRAM operation. The WRITE TO BUFFER PROGRAM command should not be used to change a bit set to 0 back to 1, and an attempt to do so is masked during the operation. Rather than the WRITE BUFFER PROGRAM command, the ERASE command should be used to set memory bits from 0 to 1. The WRITE TO BUFFER PROGRAM command can be suspended and then resumed by issuing a PROGRAM SUSPEND command and then a PROGRAM RESUME command, respectively. After the WRITE TO BUFFER PROGRAM operation has completed, the memory will return to read mode, unless an error has occurred. When an error occurs, a read operation from the bank being programmed will continue to output the status register. A read operation from any bank other than the one being programmed will output the memory array content. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations Figure 9: WRITE TO BUFFER PROGRAM Flowchart Start WRITE TO BUFFER command, block address WRITE TO BUFFER confirm, block address Write n,1 block address Read data polling register (DQ1, DQ5, DQ7) at last loaded address First three cycles of the WRITE TO BUFFER PROGRAM command Write buffer data, start address DQ7 = Data X=n No No DQ1 = 1 Yes X=0 Yes No Abort WRITE TO BUFFER Yes No DQ5 = 1 Yes Check data polling register (DQ5, DQ7) at last loaded address Write to a different block address No data,3 Write next program address pair Yes WRITE TO BUFFER and PROGRAM aborted2 DQ7 = Data4 Yes No Fail or abort5 X=X-1 Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN End 1. n + 1 is the number of addresses to be programmed. 2. The BUFFERED PROGRAM ABORT and RESET command must be issued to return the device to read mode. 3. When the block address is specified, any address in the selected block address space is acceptable. However, when loading program buffer address with data, all addresses must fall within the selected program buffer page. 4. DQ7 must be checked because DQ5 and DQ7 may change simultaneously. 5. If this flowchart location is reached because DQ5 = 1, then the WRITE TO BUFFER PROGRAM command failed. If this flowchart location is reached because DQ1 = 1, then the WRITE TO BUFFER PROGRAM command aborted. In both cases, the appropriate RESET command must be issued to return the device to read mode: A RESET command if the operation failed; a WRITE TO BUFFER PROGRAM ABORT AND RESET command if the operation aborted. 6. See the Standard Command Definitions - Address-Data Cycles, 16-Bit table for details about the WRITE TO BUFFER PROGRAM command sequence. 36 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command When the device is in unlock bypass mode, the UNLOCK BYPASS WRITE TO BUFFER (25h) command can be used to program the device in fast program mode. The command requires two bus WRITE operations fewer than the standard WRITE TO BUFFER PROGRAM command. The UNLOCK BYPASS WRITE TO BUFFER PROGRAM command behaves the same way as the WRITE TO BUFFER PROGRAM command: the operation cannot be aborted, and a bus READ operation from the memory outputs the status register. A bus READ operation from a bank different from the one whose blocks are being programmed will output the memory array content. The WRITE TO BUFFER PROGRAM CONFIRM command is used to confirm an UNLOCK BYPASS WRITE TO BUFFER PROGRAM command and to program the n + 1 words loaded in the program buffer by this command. WRITE TO BUFFER PROGRAM CONFIRM Command The WRITE TO BUFFER PROGRAM CONFIRM (29h) command is used to confirm a WRITE TO BUFFER PROGRAM command and to program the n + 1 words loaded in the program buffer by this command. BUFFERED PROGRAM ABORT AND RESET Command A BUFFERED PROGRAM ABORT AND RESET (F0h) command must be issued to abort the WRITE TO BUFFER PROGRAM and ENHANCED BUFFERED PROGRAM operations and reset the device in read mode. The buffer programming sequence can be aborted in the following ways: * Load a value that is greater than the page buffer size during the number of locations to program in the WRITE TO BUFFER PROGRAM command. * Write to an address in a different block than the one specified during the WRITE BUFFER LOAD command. * Write an address/data pair to a different write buffer page than the one selected by the starting address during the program buffer data loading stage of the operation. * Write data other than the CONFIRM command after the specified number of data load cycles. The abort condition is indicated by DQ1 = 1, DQ6 = toggle, and DQ5 = 0 (all of which are status register bits). A BUFFERED PROGRAM ABORT and RESET command sequence must be written to reset the device for the next operation. Note: The full three-cycle BUFFERED PROGRAM ABORT and RESET command sequence is required when using buffer programming features in unlock bypass mode. PROGRAM SUSPEND Command The PROGRAM SUSPEND (B0h) command can be used to interrupt a program operation so that data can be read from any block. When the PROGRAM SUSPEND command is issued during a program operation, the device suspends the operation within the program suspend latency time and updates the status register bits. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations After the program operation has been suspended, data can be read from any address. However, data is invalid when read from an address where a program operation has been suspended. The PROGRAM SUSPEND command may also be issued during a PROGRAM operation while an erase is suspended. In this case, data may be read from any address not in erase suspend or program suspend mode. To read from the extended memory block area (one-time programmable area), the ENTER/EXIT EXTENDED MEMORY BLOCK command sequences must be issued. The system may also issue the AUTO SELECT command sequence when the device is in program suspend mode. The system can read as many auto select codes as required. When the device exits auto select mode, the device reverts to program suspend mode and is ready for another valid operation. The PROGRAM SUSPEND operation is aborted by performing a device reset or powerdown. In this case, data integrity cannot be ensured, and it is recommended that the aborted data be reprogrammed. PROGRAM RESUME Command The PROGRAM RESUME (30h) command must be issued to exit a program suspend mode and resume a PROGRAM operation. The controller can use DQ7 or DQ6 status bits to determine the status of the PROGRAM operation. After a PROGRAM RESUME command is issued, subsequent PROGRAM RESUME commands are ignored. Another PROGRAM SUSPEND command can be issued after the device has resumed programming. WRITE TO BUFFER PROGRAM SUSPEND Command The WRITE TO BUFFER PROGRAM SUSPEND (B0h) command can be used to interrupt a write to buffer program operation so that data can be read from any block. When this command is issued, the device suspends the operation within the program suspend latency time and updates the status register bits. After the operation has been suspended, data can be read from any address. However, data is invalid when read from an address where a program operation has been suspended. This command can also be issued during a WRITE TO BUFFER PROGRAM operation while an erase is also suspended. In this case, data may be read from any address not in erase suspend or program suspend mode. To read from the extended memory block area (one-time programmable area), the ENTER/EXIT EXTENDED MEMORY BLOCK command sequences must be issued. The system may also issue the AUTO SELECT command sequence when the device is in write to buffer program suspend mode. The system can read as many auto select codes as required. When the device exits auto select mode, the device reverts to write to buffer program suspend mode and is ready for another valid operation. The PROGRAM SUSPEND operation is aborted by performing a device reset or powerdown. In this case, data integrity cannot be ensured, and it is recommended that the aborted data be reprogrammed. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations WRITE TO BUFFER PROGRAM RESUME Command The WRITE TO BUFFER PROGRAM RESUME (30h) command must be issued to exit a write to buffer program suspend mode and resume a WRITE TO BUFFER PROGRAM operation. The controller can use DQ7 or DQ6 status bits to determine the status of the WRITE TO BUFFER PROGRAM operation. After a WRITE TO BUFFER PROGRAM RESUME command is issued, subsequent WRITE TO BUFFER PROGRAM RESUME commands are ignored. Another WRITE TO BUFFER PROGRAM SUSPEND command can be issued after the device has resumed programming. ENTER ENHANCED BUFFERED Command The ENTER ENHANCED BUFFERED command is used to allow execution of the enhanced buffered program commands. The device accepts only these following commands after the ENTER ENHANCED BUFFERED command is issued; any other command is ignored: * ENHANCED BUFFERED PROGRAM (can be issued multiple times once the ENTER ENHANCED BUFFERED command is executed) * ENHANCED BUFFERED PROGRAM ABORT/RESET * EXIT ENHANCED BUFFERED PROGRAM To ensure the ENTER ENHANCED BUFFERED command has completed successfully and the device is ready to receive one of the commands listed above, it is recommended to monitor toggle bit (DQ6). ENHANCED BUFFERED PROGRAM Command The ENHANCED BUFFERED PROGRAM command makes use of a 256-word write buffer to speed up programming. Each write buffer has the same A23-A8 addresses. This command dramatically reduces system programming time compared to both the standard non-buffered PROGRAM command and the WRITE TO BUFFER command. When issuing the ENHANCED BUFFERED PROGRAM command, the V PP/WP pin can be held HIGH or raised to V PPH (see Program/Erase Characteristics). The following successive steps are required to issue the ENHANCED BUFFERED PROGRAM command: First, the ENTER ENHANCED BUFFERED PROGRAM command issued. Next, one bus WRITE cycle sets up the ENHANCED BUFFERED PROGRAM command. The set-up code can be addressed to any location within the targeted block. Then, a second bus WRITE cycle loads the first address and data to be programmed. There are a total of 256 address and data loading cycles. When the 256 words are loaded to the buffer, a third WRITE cycle programs the content of the buffer. Last, when the command completes, the EXIT ENHANCED BUFFERED PROGRAM command is issued. Address/data cycles must be loaded in an increasing address order, from A[7:0] = 00000000 to A[7:0] = 11111111 until all 256 words are loaded. Invalid address combinations or the incorrect sequence of bus WRITE cycles will abort the ENHANCED BUFFERED PROGRAM command. The status register bits DQ1, DQ5, DQ6, DQ7 can be used to monitor the device status during an ENHANCED BUFFERED PROGRAM operation. An external 12V supply can be used to improve programming efficiency. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 39 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations When reprogramming data in a portion of memory already programmed (changing programmed data from '0' to '1') operation failure can be detected by a logical OR between the previous and the current value. ENHANCED BUFFERED PROGRAM ABORT RESET Command After an ENHANCED BUFFERED PROGRAM command is aborted, the device will accept only an ENHANCED BUFFERED PROGRAM ABORT RESET (F0h) command. This command resets the device following the aborted command and before the next command can be executed. When this command completes and the device is reset, the memory waits for either an ENHANCED BUFFERED PROGRAM command or an EXIT ENHANCED BUFFERED PROGRAM command. The enhanced buffered programming sequence can be aborted in the following ways: * Write to an address in a different block than the one specified during the ENHANCED BUFFERED PROGRAM LOAD command. * Write an address/data pair to a different write buffer page than the one selected by the starting address during the program buffer data loading stage of the operation. * Write data other than the CONFIRM command after the specified number of data load cycles. * Load address/data pairs in an incorrect sequence during the enhanced buffered program. * Load a number of data that is less or greater than 256 during the program step. The abort condition is indicated by DQ1 = 1, DQ6 = toggle, and DQ5 = 0 (all of which are status register bits). A BUFFERED PROGRAM ABORT and RESET command sequence must be written to reset the device for the next operation. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 40 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations Figure 10: ENHANCED BUFFERED PROGRAM Flowchart Start ENHANCED BUFFERED PROGRAM command, block address ENHANCED BUFFERED PROGRAM command set First cycle of the ENHANCED BUFFERED PROGRAM command Write buffer data, start address (00), X=255 Read DQ6 at valid address Read DQ5 and DQ6 at valid address Yes X=0 No DQ6 = Abort WRITE TO BUFFER No Yes Write to a different block address toggle No Yes No ENHANCED BUFFERED PROGRAM aborted (1) Write next data, (2) program address pair DQ5 =1 Yes Write next data, (2) program address pair Read DQ6 twice at valid address X = X-1 No DQ6 = toggle ENHANCED BUFFERED PROGRAM confirm, block address Yes Fail 258th WRITE cycle of the ENHANCED BUFFERED PROGRAM command Read status register (DQ1, DQ5, DQ7) at last loaded address DQ7 = Data No DQ1 = 1 Yes No No DQ5 = 1 Yes Yes Check status register (DQ5, DQ7) at last loaded address New Program? Yes No DQ7 = Data (3) No Fail or Abort(4) Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Yes Exit ENHANCED BUFFERED PROGRAM command set End 1. The ENHANCED BUFFERED PROGRAM ABORT RESET command must be issued to return the device to read mode. 41 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program Operations 2. When the block address is specified, all addresses in the selected block address space must be issued starting from 00h. Furthermore, when loading the write buffer address with data, data program addresses must be consecutive. 3. DQ7 must be checked since DQ5 and DQ7 may change simultaneously. 4. If this flowchart location is reached because DQ5 = 1, then the ENHANCED BUFFERED PROGRAM command failed. If this flowchart location is reached because DQ1 = 1, then the ENHANCED BUFFERED PROGRAM command aborted. In both cases, the appropriate reset command must be issued to return the device to read mode: A RESET command if the operation failed; an ENHANCED BUFFERED PROGRAM ABORT RESET command if the operation aborted. EXIT ENHANCED BUFFERED PROGRAM Command The EXIT ENHANCED BUFFERED PROGRAM command requires two bus write cycles and is used to return the device to read mode. Until this command is issued, only the ENHANCED BUFFERED PROGRAM command can be issued, and all other commands are ignored. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 42 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Erase Operations Erase Operations CHIP ERASE Command The CHIP ERASE (80/10h) command erases the entire chip. Six bus WRITE operations are required to issue the command and start the program/erase controller. Protected blocks are not erased. If all blocks are protected, the CHIP ERASE operation appears to start, but will terminate within approximately100s, leaving the data unchanged. No error is reported when protected blocks are not erased. During the CHIP ERASE operation, the device ignores all other commands, including ERASE SUSPEND. It is not possible to abort the operation. All bus READ operations during CHIP ERASE output the status register on the data I/Os. See the Status Register section for more details. After the CHIP ERASE operation completes, the device returns to read mode, unless an error has occurred. If an error occurs, the device will continue to output the status register. A READ/RESET command must be issued to reset the error condition and return to read mode. The CHIP ERASE command sets all of the bits in unprotected blocks of the device to 1. All previous data is lost. The operation is aborted by performing a reset or by powering-down the device. In this case, data integrity cannot be ensured, and it is recommended that the entire chip be erased again. UNLOCK BYPASS CHIP ERASE Command When the device is in unlock bypass mode, the UNLOCK BYPASS CHIP ERASE (80/10h) command can be used to erase all memory blocks at one time. The command requires only two bus WRITE operations instead of six using the standard CHIP ERASE command. The final bus WRITE operation starts the program/erase controller. The UNLOCK BYPASS CHIP ERASE command behaves the same way as the CHIP ERASE command: the operation cannot be aborted, and a bus READ operation to the memory outputs the status register. BLOCK ERASE Command The BLOCK ERASE (80/30h) command erases a list of one or more blocks. It sets all of the bits in the unprotected selected blocks to 1. All previous data in the selected blocks is lost. Six bus WRITE operations are required to select the first block in the list. Each additional block in the list can be selected by repeating the sixth bus WRITE operation using the address of the additional block. After the command sequence is written, a block erase timeout occurs. During the timeout period, additional block addresses and BLOCK ERASE commands can be written. After the program/erase controller has started, it is not possible to select any more blocks. Therefore, each additional block must be selected within the timeout period of the last block. The timeout timer restarts when an additional block is selected. After the sixth bus WRITE operation, a bus READ operation outputs the status register. Bus READ operations from banks different from those that include the blocks being erased output the memory array content. See the WE#-Con- CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 43 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Erase Operations trolled Program waveforms for details on how to identify if the program/erase controller has started the BLOCK ERASE operation. After the BLOCK ERASE operation completes, the device returns to read mode, unless an error has occurred. If an error occurs, bus READ operations will continue to output the status register. A READ/RESET command must be issued to reset the error condition and return to read mode. If any selected blocks are protected, they are ignored, and all the other selected blocks are erased. If all of the selected blocks are protected, the BLOCK ERASE operation appears to start, but will terminate within approximately100s, leaving the data unchanged. No error condition is given when protected blocks are not erased. During the BLOCK ERASE operation, the device ignores all commands except the ERASE SUSPEND command and the READ/RESET command, which is accepted only during the timeout period. The operation is aborted by performing a reset or poweringdown the device. In this case, data integrity cannot be ensured, and it is recommended that the aborted blocks be erased again. UNLOCK BYPASS BLOCK ERASE Command When the device is in unlock bypass mode, the UNLOCK BYPASS BLOCK ERASE (80/30h) command can be used to erase one or more memory blocks at a time. The command requires two bus WRITE operations instead of six using the standard BLOCK ERASE command. The final bus WRITE operation latches the address of the block and starts the program/erase controller. To erase multiple blocks (after the first two bus WRITE operations have selected the first block in the list), each additional block in the list can be selected by repeating the second bus WRITE operation using the address of the additional block. The UNLOCK BYPASS BLOCK ERASE command behaves the same way as the BLOCK ERASE command: the operation cannot be aborted, and a bus READ operation to the memory outputs the status register. Bus READ operations from banks different from those that include the blocks being erased output the memory array content. See the BLOCK ERASE Command section for details. ERASE SUSPEND Command The ERASE SUSPEND (B0h) command temporarily suspends a BLOCK ERASE operation. One bus WRITE operation with the block address is required to issue the command. After the command sequence is written, a minimum block erase timeout occurs. During the timeout period, additional block addresses and block erase commands can be written. The program/erase controller suspends the ERASE operation within the erase suspend latency time of the ERASE SUSPEND command being issued. However, when the ERASE SUSPEND command is written during the block erase timeout, the device immediately terminates the timeout period and suspends the ERASE operation. After the program/erase controller has stopped, the device operates in read mode, and the erase is suspended. During an ERASE SUSPEND operation, it is possible to read and execute PROGRAM operations or WRITE TO BUFFER PROGRAM operations in blocks that are not suspended. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 44 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Erase Operations Both READ and PROGRAM operations behave normally on these blocks. Reading from blocks that are suspended will output the status register. If any attempt is made to program in a protected block or in the suspended block, the PROGRAM command is ignored, and the data remains unchanged. In this case, the status register is not read, and no error condition is given. It is also possible to issue the AUTO SELECT command after entering auto select mode. The READ/RESET command must be issued to return the device to read array mode before the ERASE RESUME command will be accepted. During an ERASE SUSPEND operation and after the ENTER EXTENDED MEMORY BLOCK command is issued, a bus READ operation to the extended memory block will output the extended memory block data. After the device enters extended memory block mode, the EXIT EXTENDED MEMORY BLOCK command must be issued before the ERASE operation can be resumed. An ERASE SUSPEND command is ignored if it is written during a CHIP ERASE operation. If the ERASE SUSPEND operation is aborted by performing a device reset or powerdown, data integrity cannot be ensured, and it is recommended that the suspended blocks be erased again. ERASE RESUME Command The ERASE RESUME (30h) command restarts the program/erase controller after an ERASE SUSPEND operation. The device must be in read array mode before the ERASE RESUME command will be accepted. An erase can be suspended and resumed more than once. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 45 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Block Protection Command Definitions - Address-Data Cycles Block Protection Command Definitions - Address-Data Cycles Table 17: Block Protection Command Definitions - Address-Data Cycles, 16-Bit Notes 1 and 2 apply to entire table Address and Data Cycles Command and Code/Subcode 1st Bus Size 2nd 3rd 4th A D A D A D 555 40 A nth D ... A D Notes LOCK REGISTER Commands ENTER LOCK REGISTER COMMAND SET (40h) x16 555 AA 2AA 55 PROGRAM LOCK REGISTER (A0h) x16 X A0 X Data READ LOCK REGISTER x16 X Data 3 5 4, 5, 6 PASSWORD PROTECTION Commands ENTER PASSWORD PROTECTION COMMAND SET (60h) x16 555 AA 2AA 55 555 60 3 PROGRAM PASSWORD (A0h) x16 X A0 READ PASSWORD x16 00 PWD0 01 PWD1 02 PWD2 03 PWD3 UNLOCK PASSWORD (25h/03) x16 00 25 00 03 00 PWD0 01 PWD1 ... (BKA) BAd C0 PWAn PWDn 7 4, 6, 8 00 29 8 NONVOLATILE PROTECTION Commands ENTER NONVOLATILE PROTECTION COMMAND SET (C0h) x16 555 AA 2AA 55 PROGRAM NONVOLATILE PROTECTION BIT (A0h) x16 X A0 (BKA) BAd 00 READ NONVOLATILE PROTECTION BIT STATUS x16 CLEAR ALL NONVOLATILE PROTECTION BITS (80/30h) x16 (BKA) READ(0) BAd X 80 3 4, 6, 10 00 30 11 NONVOLATILE PROTECTION BIT LOCK BIT Commands ENTER NONVOLATILE PROTECTION BIT LOCK BIT COMMAND SET (50h) x16 555 AA 2AA 55 PROGRAM NONVOLATILE PROTECTION BIT LOCK BIT (A0h) x16 X A0 X 00 READ NONVOLATILE PROTECTION BIT LOCK BIT STATUS x16 (BKA) READ(0) 555 50 3 10 4, 6, 10 VOLATILE PROTECTION Commands CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 46 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Block Protection Command Definitions - Address-Data Cycles Table 17: Block Protection Command Definitions - Address-Data Cycles, 16-Bit (Continued) Notes 1 and 2 apply to entire table Address and Data Cycles Command and Code/Subcode 1st 2nd 3rd 4th Bus Size A D A D A D ENTER VOLATILE PROTECTION COMMAND SET (E0h) x16 555 AA 2AA 55 (BKA) 555 E0 PROGRAM VOLATILE PROTECTION BIT (A0h) x16 X A0 (BKA) BAd 00 READ VOLATILE PROTECTION BIT STATUS x16 CLEAR VOLATILE PROTECTION BIT (A0h) x16 A nth D A D Notes 3 (BKA) READ(0) BAd X ... 4, 6, 10 A0 (BKA) BAd 01 2AA 55 EXTENDED MEMORY BLOCK Commands ENTER EXTENDED MEMORY BLOCK (88h) x16 555 AA READ EXTENDED MEMORY BLOCK x16 BAd RD PROGRAM EXTENDED MEMORY BLOCK x16 X A0 BAd PD EXIT EXTENDED MEMORY BLOCK (90/00h) x16 555 AA 2AA 55 X 90 X 00 555 88 555 90 3 X 00 EXIT PROTECTION Commands EXIT PROTECTION COMMAND SET (90/00h) Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN x16 3 1. Key: A = Address and D = Data; X = "Don't Care;" BAd = any address in the block; BKA = Bank address; PWDn = password bytes 0 to 7; PWAn = password address, n = 0 to 7; RD(0) = DQ0 protection indicator bit; If protected, DQ0 = 00h, while if unprotected, DQ0 = 01h. Gray = not applicable. All values in the table are hexadecimal. 2. DQ[15:8] are "Don't Care" during UNLOCK and COMMAND cycles. A[MAX:16] are "Don't Care" during UNLOCK and COMMAND cycles, unless an address is required. 3. The ENTER command sequence must be issued prior to any operation. It disables READ and WRITE operations from and to block 0. READ and WRITE operations from and to any other block are allowed. Also, when an ENTER COMMAND SET command is issued, an EXIT PROTECTION COMMAND SET command must be issued to return the device to READ mode. 4. READ REGISTER/PASSWORD commands have no command code; CE# and OE# are driven LOW and data is read according to a specified address. 5. Data = Lock register content. 6. All address cycles shown for this command are READ cycles. 7. Only one portion of the password can be programmed by each PROGRAM PASSWORD command. 8. Each portion of the password can be entered or read in any order as long as the entire 64-bit password is entered or read. 9. For the x16 UNLOCK PASSWORD command, the nth (and final) address cycle equals the 7th address cycle. For the 5th and 6th address cycles, the values for the address and data 47 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Protection Operations pair continue the pattern shown in the table as follows: address and data = 02 and PWD2; 03 and PWD3. 10. Both nonvolatile and volatile protection bit settings are as follows: Protected state = 00; Unprotected state= 01. 11. The CLEAR ALL NONVOLATILE PROTECTION BITS command programs all nonvolatile protection bits before erasure. This prevents over-erasure of previously cleared nonvolatile protection bits. Protection Operations Blocks can be protected individually against accidental PROGRAM and ERASE operations. The block protection scheme is shown in the Software Protection Scheme figure. Memory block and extended memory block protection is configured through the lock register. LOCK REGISTER Commands The ENTER LOCK REGISTER COMMAND SET (40h) requires three bus write cycles. After it has been issued, all bus READ or PROGRAM operations can be issued to the lock register. The EXIT PROTECTION COMMAND SET (90/00h) command must be used to exit the lock register ane return to read mode. The PROGRAM LOCK REGISTER (A0h) command allows the lock register to be configured. The programmed data can then be checked with a READ LOCK REGISTER command by driving CE# and OE# LOW with the appropriate address data on the address bus. PASSWORD PROTECTION Commands After the ENTER PASSWORD PROTECTION COMMAND SET (60h) command has been issued, only commands related to password protection mode and the EXIT PROTECTION COMMAND SET command can be issued to the device. This command requires three bus write cycles. The EXIT PROTECTION COMMAND SET command must be issued following all password protection commands to return the device to read mode. The PROGRAM PASSWORD (A0h) command is used to program the 64-bit password used in the password protection mode. To program the 64-bit password, the complete command sequence must be entered four times at four consecutive addresses selected by A[1:0] in 16-bit mode. This command must be used according to all program command timings. Command results can be verified by checking the status register. By default, all password bits are set to 1. The password can be checked by issuing a READ PASSWORD command. The READ PASSWORD command is used to verify the password used in password protection mode. To verify the 64-bit password, the complete command sequence must be entered four times at four consecutive addresses selected by A[1:0] in 16-bit mode. If the password mode lock bit is programmed and the user attempts to read the password, the device will output FFh onto the I/O data bus. The UNLOCK PASSWORD (25/03h) command is used to clear the nonvolatile protection bit lock bit, allowing the nonvolatile protection bits to be modified. The UNLOCK PASSWORD command must be issued, along with the correct password, and requires a CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 48 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Protection Operations 1s delay between successive UNLOCK PASSWORD commands in order to prevent unauthorized intruders from retrieving the password by trying all possible 64-bit combinations. If this delay does not occur, the latest command will be ignored. Approximately 1s is required for unlocking the device after the valid 64-bit password has been provided. NONVOLATILE PROTECTION Commands After the ENTER NONVOLATILE PROTECTION COMMAND SET (C0h) command has been issued, the commands related to nonvolatile protection mode can be issued to the device. This command requires three bus write cycles. A block can be protected from program or erase by issuing a PROGRAM NONVOLATILE PROTECTION BIT (A0h) command, along with the block address. This command sets the nonvolatile protection bit to 0 for a given block. This command must be used according to all program command timings. Command results can be verified by checking the status register. The status of a nonvolatile protection bit for a given block or group of blocks can be read by issuing a READ NONVOLATILE MODIFY PROTECTION BIT command, along with the block address. The nonvolatile protection bits are erased simultaneously by issuing a CLEAR ALL NONVOLATILE PROTECTION BITS (80/30h) command. No specific block address is required. If the nonvolatile protection bit lock bit is set to 0, the command fails. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 49 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Protection Operations Figure 11: Program/Erase Nonvolatile Protection Bit Algorithm Start ENTER NONVOLATILE PROTECTION command set PROGRAM NONVOLATILE PROTECTION BIT Addr = BAd Read byte twice Addr = BAd DQ6 = Toggle No Yes No DQ5 = 1 Wait 500s Yes Read byte twice Addr = BAd DQ6 = Toggle No Read byte twice Addr = BAd Yes No DQ0 = 1 (erase) 0 (program) Yes Fail Reset Pass EXIT PROTECTION command set NONVOLATILE PROTECTION BIT LOCK BIT Commands After the ENTER NONVOLATILE PROTECTION BIT LOCK BIT COMMAND SET (50h) command has been issued, the commands that allow the nonvolatile protection bit lock bit to be set can be issued to the device. This command requires three bus write cycles. The PROGRAM NONVOLATILE PROTECTION BIT LOCK BIT (A0h) command is used to set the nonvolatile protection bit lock bit to 0, thus locking the nonvolatile protection bits and preventing them from being modified. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 50 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Protection Operations The READ NONVOLATILE PROTECTION BIT LOCK BIT STATUS command is used to read the status of the nonvolatile protection bit lock bit. VOLATILE PROTECTION Commands After the ENTER VOLATILE PROTECTION COMMAND SET (E0h) command has been issued, commands related to the volatile protection mode can be issued to the device. This command requires three bus write cycles. The PROGRAM VOLATILE PROTECTION BIT (A0h) command individually sets a volatile protection bit to 0 for a given block. If the nonvolatile protection bit for the same block is set, the block is locked regardless of the value of the volatile protection bit. (See the Block Protection Status table.) The status of a volatile protection bit for a given block can be read by issuing a READ VOLATILE PROTECTION BIT STATUS command along with the block address. The CLEAR VOLATILE PROTECTION BIT (A0h) command individually clears (sets to 1) the volatile protection bit for a given block. If the nonvolatile protection bit for the same block is set, the block is locked regardless of the value of the volatile protection bit. (See the Block Protection Status table.) EXTENDED MEMORY BLOCK Commands The device has one extra 256-word block (extended memory block) that can only be accessed by the ENTER EXTENDED MEMORY BLOCK command when the device is in extended block mode. The device can be shipped with the extended memory block prelocked permanently by Micron, or with the extended memory block unlocked, enabling customers to permanently program and lock it. (See Lock Register, the AUTO SELECT command, and the Block Protection table.) The extended memory block is used as a security block (to provide a permanent security identification number) or to store additional information. The extended memory block is divided in two memory areas of 128 words each: The first area is factory locked and the second one is customer lockable. It is permanently protected from program operations and cannot be unprotected. The random number, electronic serial number (ESN) and security identification number are written in this section in the factory. The second area is customer lockable. It is up to the customer to protect it from program operations. Its status is indicated by bit DQ6 and DQ7. When DQ7 is set to 1 and DQ6 to 0, it indicates that this second memory area is customer lockable. When DQ7 and DQ6 are both set to 1, it indicates that the second part of the extended memory block is customer locked and protected from program operations. Bits DQ6 and DQ7 are the most significant bits in the extended block protection indicator and a specific procedure must be followed to read it. Table 18: Extended Memory Block Address and Data Data Address Micron prelocked 000000h-00007Fh Secure ID number Unavailable 000080h-0000FFh Unavailable Determined by customer CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 51 Customer Lockable Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Protection Operations Three Bus Write cycles are required to issue the Extended Memory Block command. Once the command has been issued the device enters the extended memory block mode where all bus read or program operations are conducted on the extended memory block. Once the device is in the extended block mode, the extended memory block is addressed by using the addresses occupied by block 0 in the other operating modes (see the Memory Map table). The device remains in extended memory block mode until the EXIT EXTENDED MEMORY BLOCK command is issued or power is removed from the device. After power-up or hardware reset, the device reverts to read mode where the commands issued to the block 0 address space will properly address block 0. The extended memory block cannot be erased, and can be treated as one-time programmable (OTP) memory. In extended block mode, Erase, Chip Erase, Erase Suspend and Erase Resume commands are not allowed. To exit from the extended memory block mode the EXIT EXTENDED MEMORY BLOCK command must be issued. This command requires four bus write cycles. The extended memory block can be protected by setting the extended memory block protection bit to 0 (see Lock Register); however once protected the protection cannot be undone. Note: When the device is in the extended memory block mode, the VPP/WP pin cannot be used for fast programming and the unlock bypass mode is not available (see V PP// WP). EXIT PROTECTION Command The EXIT PROTECTION COMMAND SET (90/00h) command is used to exit the lock register, password protection, nonvolatile protection, volatile protection, and nonvolatile protection bit lock bit command set modes and return the device to read mode. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 52 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Device Protection Device Protection Hardware Protection The V PP/WP# function provides a hardware method of protecting the four outermost blocks; that is, the two 32-kword blocks at the top and the two 32-KWord blocks at the bottom of the address space. When V PP/WP# is LOW, PROGRAM and ERASE operations on the four outermost blocks are ignored to provide protection. When V PP/WP# is HIGH, the device reverts to the previous protection status for these four outermost blocks. PROGRAM and ERASE operations can modify the data in these blocks unless the blocks are protected using block protection. When V PP/WP# is raised to VPPH, the device automatically enters the unlock bypass mode, and command execution time is faster. This must never be done from any mode except read mode; otherwise the device might be left in an indeterminate state. A 0.1 F capacitor should be connected between the V PP/WP# pin and the VSS ground pin to decouple the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required during unlock bypass program. When V PP/WP# returns to HIGH or LOW, normal operation resumes. When operations execute in unlock bypass mode, the device draws IPP from the pin to supply the programming circuits. Transitions from HIGH to VPPH and from VPPH to LOW must be slower than tVHVPP. Note: Micron highly recommends driving V PP/WP# HIGH or LOW. If a system needs to float the V PP/WP# pin, without a pull-up/pull-down resistor and no capacitor, then an internal pull-up resistor is enabled. Table 19: VPP/WP# Functions VPP/WP# Settings Function VIL Four outermost parameter blocks (first two and last two) protected from PROGRAM or ERASE operations. VIH Four outermost parameter blocks (first two and last two) unprotected from PROGRAM or ERASE operations, unless a software activated protection is in place. VPPH Unlock bypass mode supplies current necessary to speed up PROGRAM execution time. Software Protection The following software protection modes are available: * Volatile protection * Nonvolatile protection * Password protection The device is shipped with all blocks unprotected. On first use, the device defaults to the nonvolatile protection mode but can be activated in either the nonvolatile protection or password protection mode. The desired protection mode is activated by setting either the nonvolatile protection mode lock bit or the password protection mode lock bit of the lock register (see the Lock Register section). Both bits are one-time-programmable and nonvolatile; therefore, after the protection mode has been activated, it cannot be changed, and the device is set CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 53 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Device Protection permanently to operate in the selected protection mode. It is recommended that the desired software protection mode be activated when first programming the device. For the four outermost blocks (that is the two blocks at the top and the two at the bottom of the address space), an even higher level of block protection can be achieved by locking the blocks using the non-volatile protection and then by holding V PP /WP# LOW. Blocks with volatile protection and nonvolatile protection can coexist within the memory array. If the user attempts to program or erase a protected block, the device ignores the command and returns to read mode. The block protection status can be read by performing a read electronic signature or by issuing an AUTO SELECT command (see the Block Protection table). Refer to the Block Protection Status table and the Software Protection Scheme figure for details on the block protection scheme. Refer to the Protection Operations section for a description of the command sets. Volatile Protection Mode Volatile protection enables the software application to protect blocks against inadvertent change and can be disabled when changes are needed. Volatile protection bits are unique for each block and can be individually modified. Volatile protection bits control the protection scheme only for unprotected blocks whose nonvolatile protection bits are cleared to 1. Issuing a PROGRAM VOLATILE PROTECTION BIT or CLEAR VOLATILE PROTECTION BIT command sets to 0 or clears to 1 the volatile protection bits and places the associated blocks in the protected (0) or unprotected (1) state, respectively. The volatile protection bit can be set or cleared as often as needed. The default values of the volatile protections are set through the volatile lock boot bit of the lock register (See the Lock Register section). When the parts are first shipped, or after a power-up or hardware reset, the volatile protection bits can be set or cleared depending upon the ordering option chosen: if the option to clear the volatile protection bits after power-up is selected, then the blocks can be programmed or erased depending on the nonvolatile protection bits state (See the Block Protection Status table); If the option to set the volatile protection bits after power-up is selected, the blocks default to be protected (Refer also to the Protection commands). Nonvolatile Protection Mode A nonvolatile protection bit is assigned to each block. Each of these bits can be set for protection individually by issuing a PROGRAM NONVOLATILE PROTECTION BIT command. Also, each device has one global volatile bit called the nonvolatile protection bit lock bit; it can be set to protect all nonvolatile protection bits at once. This global bit must be set to 0 only after all nonvolatile protection bits are configured to the desired settings. When set to 0, the nonvolatile protection bit lock bit prevents changes to the state of the nonvolatile protection bits. When cleared to 1, the nonvolatile protection bits can be set and cleared using the PROGRAM NONVOLATILE PROTECTION BIT and CLEAR ALL NONVOLATILE PROTECTION BITS commands, respectively. No software command unlocks the nonvolatile protection bit lock bit unless the device is in password protection mode; in nonvolatile protection mode, the nonvolatile protecCCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 54 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Device Protection tion bit lock bit can be cleared only by taking the device through a hardware reset or power-up. Nonvolatile protection bits cannot be cleared individually; they must be cleared all at once using a CLEAR ALL NONVOLATILE PROTECTION BITS command. They will remain set through a hardware reset or a power-down/power-up sequence. If one of the nonvolatile protection bits needs to be cleared (unprotected), additional steps are required: First, the nonvolatile protection bit lock bit must be cleared to 1, using either a power-cycle or hardware reset. Then, the nonvolatile protection bits can be changed to reflect the desired settings. Finally, the nonvolatile protection bit lock bit must be set to 0 to lock the nonvolatile protection bits. The device now will operate normally. To achieve the best protection, the PROGRAM NONVOLATILE PROTECTION LOCK BIT command should be executed early in the boot code, and the boot code should be protected by holding V PP/WP# LOW. Nonvolatile protection bits and volatile protection bits have the same function when VPP/WP# is HIGH or when V PP/WP# is at the voltage for program acceleration (VPPH ). Password Protection Mode Password protection mode provides a higher level of security than the nonvolatile protection mode by requiring a 64-bit password to unlock the nonvolatile protection bit lock bit. In addition to this password requirement, the nonvolatile protection bit lock bit is set to 0 after power-up and reset to maintain the device in password protection mode. Executing the UNLOCK PASSWORD command by entering the correct password clears the nonvolatile protection bit lock bit, enabling the block nonvolatile protection bits to be modified. If the password provided is incorrect, the nonvolatile protection bit lock bit remains locked, and the state of the nonvolatile protection bits cannot be modified. To place the device in password protection mode, the following two steps are required: First, before activating the password protection mode, a 64-bit password must be set and the setting verified. Password verification is allowed only before the password protection mode is activated. Next, password protection mode is activated by programming the password protection mode lock bit to 0. This operation is irreversible; after the bit is programmed, it cannot be erased. The device remains permanently in password protection mode, and the 64-bit password can be neither retrieved nor reprogrammed. In addition, all commands to the address where the password is stored are disabled. Note: There is no means to verify the password after password protection mode is enabled. If the password is lost after enabling the password protection mode, there is no way to clear the nonvolatile protection bit lock bit. NVPBs default to `1' (block unprotected) after power-up and hardware reset. A block is protected or unprotected when its NVPB is set to `0' and `1', respectively. NVPBs are programmed individually and cleared collectively. VPB default status depends on ordering option. A block is protected or unprotected when its VPB is set to `0' and `1', respectively. VPBs are programmed and cleared individually. For the volatile protection to be effective, the NVPB lock bit must be set to `0' (NVPB bits unlocked) and the block NVPB must be set to `1' (block unprotected). CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 55 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Device Protection 3. The NVPB lock bit is volatile and default to `1' (NVPB bits unlocked) after power-up and hardware reset. NVPB bits are locked by setting the NVPB lock bit to `0'. Once programmed to `0', the NVPB lock bit can be reset to `1' only be taking the device through a power-up or hardware reset. Figure 12: Software Protection Scheme Volatile protection bit 1 = unprotected 0 = protected (Default setting depends on the product order option) Volatile protection Nonvolatile protection bit 1 = unprotected (default) 0 = protected Nonvolatile protection Nonvolatile protection bit lock bit (volatile) Array block 1 = unlocked (default, after power-up or hardware reset) 0 = locked Nonvolatile protection mode Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Password protection mode 1. Nonvolatile protection bits default to 1 (block unprotected) when the parts are first shipped. A block is protected or unprotected when its nonvolatile protection bit is set to 0 and 1, respectively. 2. Volatile protection bits are programmed and cleared individually. Nonvolatile protection bits are programmed individually and cleared collectively. 3. Volatile protection bit default status depends on ordering option. A block is protected or unprotected when its volatile protection bit is set to 0 and 1, respectively. For the volatile protection to be effective, the block nonvolatile protection bit must be set to 1 (block unprotected). 4. Once programmed to 0, the nonvolatile protection bit lock bit can be reset to 1 only by taking the device through a power-up or hardware reset. 56 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Dual Operations and Multiple Bank Architecture Dual Operations and Multiple Bank Architecture The multiple bank architecture gives greater flexibility for software developers to split the code and data spaces within the memory array. The dual operations feature simplifies the software management of the device by allowing code to be executed from one bank while another bank is being programmed or erased. The dual operations feature means that while programming or erasing in one bank, read operations are possible in another bank with zero latency. Only one bank at a time is allowed to be in program or erase mode. However, certain commands can cross bank boundaries, which means that during an operation only the banks that are not concerned with the cross bank operation are available for dual operations. For example, if a Block Erase command is issued to erase blocks in both bank A and bank B, then only banks C or D are available for read operations while the erase is being executed. If a read operation is required in a bank, which is programming or erasing, the program or erase operation can be suspended. Also if the suspended operation was erase then a program command can be issued to another block, so the device can have one block in erase suspend mode, one programming and other banks in read mode. By using a combination of these features, read operations are possible at any moment. The tables below show the dual operations possible in other banks and in the same bank. Note that only the commonly used commands are represented in these tables. Table 20: Dual Operations Allowed in Other Banks Commands Allowed in Another Bank Status of bank Read Read Status Register2 Read CFI Query Auto Select Program Erase Idle Yes Yes3 Yes Yes Yes Yes Yes3 Yes4 Programming Yes No No No - - No No Program/Erase Program/Erase Suspend Resume Erasing Yes No No No - - No No Program suspended Yes No No Yes No No - No Erase suspended Yes No No Yes Yes No - Yes5 Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. If several banks are involved in a program or erase operation, then only the banks that are not concerned with the operation are available for dual operations. 2. Read Status Register is not a command. The status register can be read during a block program or erase operation. 3. Only after a program or erase operation in that bank. 4. Only after a Program or Erase Suspend command in that bank. 5. Only an erase resume is allowed if the bank was previously in erase suspend mode. 57 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Dual Operations and Multiple Bank Architecture Table 21: Dual Operations Allowed in Same Bank Commands Allowed in Same Bank Status of bank Read Read Status Register1 Read CFI Query Auto Select Program Erase Program/Erase Suspend Program/Erase Resume Idle Yes Yes Yes Yes Yes Yes Yes2 Yes3 Programming No Yes No No - - Yes4 - - Erasing No Yes No No - No Yes5 Program suspended Yes No No Yes No - - Yes Erase suspended Yes6 Yes7 No Yes Yes6 No - Yes Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. Read status register is not a command. The status register can be read during a block program or erase operation. 2. Only after a program or erase operation in that bank. 3. Only after a Program or Erase Suspend command in that bank. 4. Only a program suspend. 5. Only an erase suspend. 6. Not allowed in the block or word that is being erased or programmed. 7. The status register can be read by addressing the block being erase suspended. 58 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Common Flash Interface Common Flash Interface The common flash interface is a JEDEC approved, standardized data structure that can be read from the flash memory device. It allows a system software to query the device to determine various electrical and timing parameters, density information and functions supported by the memory. The system can interface easily with the device, enabling the software to upgrade itself when necessary. When the Read CFI Query command is issued, the memory enters read CFI query mode and read operations output the CFI data. The tables here show the addresses (A0-A7) used to retrieve the data. The CFI data structure also contains a security area where a 64-bit unique security number is written (see Table 40: Security Code Area). This area can be accessed only in read mode by the final user. It is impossible to change the security number after it has been written by Micron. Table 22: Query Structure Overview Note applies to the entire table. Address x16 Sub-section name 10h CFI query identification string Command set ID and algorithm data offset 1Bh System interface information Device timing & voltage information 27h Device geometry definition 40h Primary algorithm-specific extended query table 61h Security code area Note: Description Flash device layout Additional information specific to the primary algorithm (optional) 64-bit unique device number 1. Query data are always presented on the lowest order data outputs. Table 23: CFI Query Identification String Note applies to the entire table. Address x16 Data 10h 0051h 11h 0052h 12h 0059h 13h 0002h 14h 0000h 15h 0040h 16h 0000h 17h 0000h 18h Description Value `Q' Query unique ASCII string `QRY' `R' `Y' Primary algorithm command set and control interface ID code 16 bit ID code defining a specific algorithm Spansion compatible Address for primary algorithm extended query table (see the Primary Algorithm-Specific Extended Query Table) P = 40h NA 0000h Alternate vendor command set and control interface ID code second vendor - specified algorithm supported 19h 0000h Address for alternate algorithm extended query table NA 1Ah 0000h Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. Query data are always presented on the lowest order data outputs (DQ7-DQ0) only. DQ8-DQ15 are `0'. 59 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Common Flash Interface Table 24: CFI Query System Interface Information Note applies to the entire table. Address x16 Data Description Value 1Bh 0027h VCC logic supply minimum program/erase voltage bit 7 to 4 BCD value in volts bit 3 to 0 BCD value in 100 mV 2.7 V 1Ch 0036h VCC logic supply maximum program/erase voltage bit 7 to 4 BCD value in volts bit 3 to 0 BCD value in 100 mV 3.6 V 1Dh 0085h VPPH [programming] supply minimum program/erase voltage bit 7 to 4 HEX value in volts bit 3 to 0 BCD value in 100 mV 8.5 V 1Eh 0095h VPPH [programming] supply maximum program/erase voltage bit 7 to 4 HEX value in volts bit 3 to 0 BCD value in 100 mV 9.5 V 1Fh 0004h Typical timeout for single word program = 2n s 16 s 20h 0004h Typical timeout for minimum size write buffer program = 21h 0009h Typical timeout for individual block erase = 2n ms 22h 23h 0011h 0004h Typical timeout for full chip erase = 2n 2n s 0.5 s ms Maximum timeout for word program = 2n 80 s times typical 2n 24h 0004h Maximum timeout for write buffer program = 25h 0003h Maximum timeout per individual block erase = 2n times typical 26h 0004h Note: Maximum timeout for chip erase = 2n 16 s times typical times typical 200 s 200 s 2.3 s 800 s 1. The values given in the above table are valid for both packages. Table 25: Device Geometry Definition Address x16 27h Data 0019h Description Device size = Value 2n in number of bytes 32 Mbytes 28h 29h 0001h 0000h Flash device interface code description 2Ah 2Bh 0006h 0000h Maximum number of bytes in multiple-byte program or page= 2n x16 async. 64 2Ch 0003h Number of Erase block regions. It specifies the number of regions containing contiguous Erase blocks of the same size. 3 2Dh 2Eh 2Fh 30h 0003h 0000h 0000h 0001h 31h 32h 33h 34h Erase block region 1 information 2Dh-2Eh: number of erase blocks of identical size 2Fh-30h: block size (n*256 bytes) 4 blocks, 32-Kwords 007Dh 0000h 0000h 0004h Erase block region 2 information 126 blocks, 128-Kwords 35h 36h 37h 38h 0003h 0000h 0000h 0001h Erase block region 3 information 4 blocks, 32-Kwords 39h 3Ah 3Bh 3Ch 0000h 0000h 0000h 0000h Erase block region 4 information NA CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 60 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Common Flash Interface Table 26: Primary Algorithm-Specific Extended Query Table Address x16 Data Description Value 40h 0050h Primary algorithm extended query table unique ASCII string "PRI" 41h 0052h 42h 0049h 43h 0031h Major version number, ASCII `1' 44h 0033h Minor version number, ASCII `3' 45h 0010h Address sensitive unlock (bits 1 to 0) 00 = required, 01= not required Silicon revision number (bits 7 to 2) 46h 0002h Erase suspend 00 = not supported, 01 = read only, 02 = read and write 2 47h 0001h Block protection 00 = not supported, x = number of blocks per group 1 48h 0000h Temporary block unprotect 00 = not supported, 01 = supported 49h 0008h Block protect /unprotect 08 = M29DW256G 4Ah 0073h Simultaneous operations: x= block number (excluding bank A) 4Bh 0000h Burst mode, 00 = not supported, 01 = supported 4Ch 0002h Page mode, 00 = not supported, 02 = 8-word page 4Dh 0085h VPPH supply minimum program/erase voltage bit 7 to 4 HEX value in volts bit 3 to 0 BCD value in 100 mV 8.5 V 4Eh 0095h VPPH supply maximum program/erase voltage bit 7 to 4 HEX value in volts bit 3 to 0 BCD value in 100 mV 9.5 V 4Fh 0001h 01 = Dual Boot Dual Boot 50h 0001h Program suspend, 00 = not supported, 01 = supported Supported 51h 0001h Unlock bypass: 00 = not supported, 01 = supported Supported `P' `R' `I' Yes 65 nm Not supported 8 115 Not supported 2n 02 52h 0008h Extended memory block size (customer lockable), 57h 0004h Bank organization, 00 = data at 4Ah is 0, x= bank number 4 58h 0013h Bank A information, x = number of blocks in bank A 19 59h 0030h Bank B information, x = number of blocks in bank B 48 5Ah 0030h Bank C information, x = number of blocks in bank C 48 5Bh 0013h Bank D information, x = number of blocks in bank D 19 Note: bytes 256 1. The values given in the above table are valid for both packages. Table 27: Security Code Area Address CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN x16 Data Description 61h XXXX 64-bit: unique device number 62h XXXX 63h XXXX 64h XXXX 61 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Power-Up and Reset Characteristics Power-Up and Reset Characteristics Table 28: Power-Up Wait Timing Specifications Note 1 applies to the entire table Symbol Parameter VCC HIGH to CE# LOW VCCQ HIGH to CE# LOW VCC HIGH to WE# LOW VCCQ HIGH to WE# LOW Notes: Legacy JEDEC Min Max Unit Notes tVCH tVCHEL 55 - s 2 - tVCQHEL 55 - s 2 - tVCHWL 500 - s - tVCQHWL 500 - s 1. Specifications apply to 70 and 80ns devices unless otherwise noted. 2. VCC and VCCQ ramps must be synchronized during power-up. Figure 13: Power-Up Timing tVCHEL VCC VCCQ tVCQHEL CE# WE# tVCHWL tVCQHWL RST# tRH CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 62 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Power-Up and Reset Characteristics Table 29: Reset AC Specifications Note 1 applies to the entire table Symbol Condition/Parameter Legacy JEDEC Min Max Unit Notes RST# LOW to read mode during program or erase tREADY tPLRH - 55 s 2 RST# pulse width tRP tPLPH 20 - s RST# HIGH to CE# LOW, OE# LOW tRH tPHEL, 55 - ns 20 - s 55 - s 0 - ns 2 tPHGL, tPHWL tRPD RST# LOW to standby mode during read mode - RST# LOW to standby mode during program or erase tRB RY/BY# HIGH to CE# LOW, OE# LOW tRHEL, 2 tRHGL, tRHWL Notes: 1. Specifications apply to 70 and 80ns devices unless otherwise noted. 2. Sampled only; not 100% tested. Figure 14: Reset AC Timing - No PROGRAM/ERASE Operation in Progress RY/BY# CE#, OE#, WE# tRH RST# tRP Figure 15: Reset AC Timing During PROGRAM/ERASE Operation tREADY RY/BY# tRB CE#, OE#, WE# tRH RST# tRP CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 63 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Absolute Ratings and Operating Conditions Absolute Ratings and Operating Conditions Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may adversely affect reliability. Table 30: Absolute Maximum/Minimum Ratings Parameter Symbol Min Max Unit Temperature under bias TBIAS -50 125 C Storage temperature TSTG -65 150 C Input/output voltage VIO -0.6 VCC + 0.6 V Supply voltage VCC -0.6 4 V Input/output supply voltage VCCQ -0.6 4 V Program voltage VPPH -0.6 10.5 V Notes: Notes 1, 2 3 1. During signal transitions, minimum voltage may undershoot to -2V for periods less than 20ns. 2. During signal transitions, maximum voltage may overshoot to VCC + 2V for periods less than 20ns. 3. VPPH must not remain at 9V for more than 80 hours cumulative. Table 31: Operating Conditions 70ns Parameter 80ns Symbol Min Max Min Max Unit Supply voltage VCC 2.7 3.6 2.7 3.6 V Input/output supply voltage (VCCQ VCC) VCCQ 2.7 3.6 1.65 3.6 V Ambient operating temperature (range 1) TA 0 70 0 70 C Ambient operating temperature (range 6) TA -40 85 -40 85 C Load capacitance CL Input rise and fall times - Input pulse voltages - 0 to VCCQ 0 to VCCQ V Input and output timing reference voltages - VCCQ/2 VCCQ/2 V CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 30 - 64 30 10 - pF 10 ns Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Absolute Ratings and Operating Conditions Figure 16: AC Measurement Load Circuit VCCQ VPP VCC 25k Device under test CL 0.1F 25k 0.1F Note: 1. CL includes jig capacitance. Figure 17: AC Measurement I/O Waveform VCCQ VCCQ/2 0V Table 32: Input/Output Capacitance1 Parameter Input capacitance Output capacitance Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Symbol Test Condition Min Max Unit CIN VIN = 0V - 6 pF COUT VOUT = 0V - 12 pF 1. Sampled only, not 100% tested. 65 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash DC Characteristics DC Characteristics Table 33: DC Current Characteristics Parameter Input leakage current Symbol Conditions Min Typ Max Unit Notes ILI 0V VIN VCC - - 1 A 1 Output leakage current ILO 0V VOUT VCC - - 1 A VCC read current ICC1 CE# = VIL, OE# = VIH, f = 6 MHz - - 10 mA CE# = VIL, OE# = VIH, f = 10 MHz - - 1 mA CE# = VCCQ 0.2V, RST# = VCCQ 0.2V - - 100 A VPP/WP# = VIL or VIH - - 20 mA VPP/WP# = VPPH - - 15 mA - 1 5 A - 1 5 A Random read Page read VCC standby current ICC2 VCC program/erase current ICC3 VPP current Read Program/ erase controller active VPP/WP# VCC IPP1 Standby Reset IPP2 RST# = VSS 0.2V - 1 5 A PROGRAM operation ongoing IPP3 VPP/WP# = 12V 5% - 1 10 mA VPP/WP# = VCC - 1 5 mA ERASE operation ongoing IPP4 VPP/WP# = 12V 5% - 3 10 mA VPP/WP# = VCC - 1 5 mA Notes: 2 1. The maximum input leakage current is 5A on the VPP/WP# pin. 2. Sampled only; not 100% tested. Table 34: DC Voltage Characteristics Symbol Conditions Min Typ Max Unit Input LOW voltage Parameter VIL VCC 2.7V -0.5 - 0.3VCCQ V Input HIGH voltage VIH VCC 2.7V 0.7VCCQ - VCCQ + 0.4 V Output LOW voltage VOL IOL = 100A, VCC = VCC,min, VCCQ = VCCQ,min - - 0.15VCCQ V Output HIGH voltage VOH IOH = 100A, VCC = VCC,min, VCCQ = VCCQ,min 0.85VCCQ - - V Voltage for VPP/WP# program acceleration VPPH - - 8.5 9.5 V Program/erase lockout supply voltage VLKO - 1.8 - 2.5 V Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Notes 1 1. Sampled only; not 100% tested. 66 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Read AC Characteristics Read AC Characteristics Table 35: Read AC Characteristics Symbol 70ns VCCQ = VCC Parameter 80ns VCCQ = 1.65V to VCC Legacy JEDEC Condition Min Max Min Max Unit Address valid to next address valid tRC tAVAV CE# = VIL, OE# = VIL 70 - 80 - ns Address valid to output valid tACC tAVQV CE# = VIL, OE# = VIL - 70 - 80 ns Address valid to output valid (page) tPAGE tAVQV1 CE# = VIL, OE# = VIL - 25 - 30 ns CE# LOW to output transition tLZ tELQX OE# = VIL 0 - 0 - ns tE tELQV OE# = VIL - 70 - 80 ns tOLZ tGLQX CE# = VIL 0 - 0 - ns OE# LOW to output valid tOE tGLQV CE# = VIL - 25 - 30 ns CE# HIGH to output High-Z tHZ tEHQZ OE# = VIL - 25 - 30 ns 1 OE# HIGH to output High-Z tDF tGHQZ CE# = VIL - 25 - 30 ns 1 CE#, OE#, or address transition to output transition tOH tEHQX, - 0 - 0 - ns CE# LOW to output valid OE# LOW to output transition Notes 1 1 tGHQX, tAXQX Note: 1. Sampled only; not 100% tested. Figure 18: Random Read AC Timing tRC A[MAX:0] Valid tACC tOH CE# tE tOH tLZ tHZ OE# tOLZ tOH tOE tDF DQ[15:0] CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Valid 67 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Read AC Characteristics Figure 19: Page Read AC Timing A[23:3] VALID A[2:0] VALID VALID VALID VALID VALID VALID VALID VALID tAVQV CE# tEHQX tELQV tEHQZ OE# tGHQX tGLQV tGHQZ tAVQV1 DQ[15:0] CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN VALID VALID VALID VALID 68 VALID VALID VALID VALID Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Write AC Characteristics Write AC Characteristics Table 36: WE#-Controlled Write AC Characteristics Parameter 70ns VCCQ = VCC Symbol 80ns VCCQ = 1.65V to VCC Unit Legacy JEDEC Min Max Min Max tWC tAVAV 70 - 80 - ns CE# LOW to WE# LOW tCS tELWL 0 - 0 - ns WE# LOW to WE# HIGH tWP tWLWH 35 - 35 - ns Input valid to WE# HIGH tDS tDVWH 45 - 45 - ns WE# HIGH to input transition tDH tWHDX 0 - 0 - ns WE# HIGH to CE# HIGH tCH tWHEH 0 - 0 - ns WE# HIGH to WE# LOW tWPH tWHWL 30 - 30 - ns Address valid to WE# LOW tAS tAVWL 0 - 0 - ns WE# LOW to address transition tAH tWLAX 45 - 45 - ns OE# HIGH to WE# LOW - tGHWL 0 - 0 - ns WE# HIGH to OE# LOW tOEH tWHGL 0 - 0 - ns Program/erase valid to RY/BY# LOW tBUSY tWHRL - 30 - 30 ns tVCS tVCHEL 50 - 50 - s Address valid to next address valid VCC HIGH to CE# LOW Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN Notes 1 1. Sampled only; not 100% tested. 69 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Write AC Characteristics Figure 20: WE#-Controlled Program AC Timing 3rd Cycle 4th Cycle Data Polling tWC READ Cycle tWC A[MAX:0] 555h PA PA tAH tAS tCH tCS tE CE# tGHWL tOE OE# tWPH tWP WE# tWHWH1 tDS DQ[15:0] AOh PD DQ7# tDF DOUT tOH DOUT tDH Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. Only the third and fourth cycles of the PROGRAM command are represented. The PROGRAM command is followed by checking of the status register data polling bit and by a READ operation that outputs the data (DOUT) programmed by the previous PROGRAM command. 2. PA is the address of the memory location to be programmed. PD is the data to be programmed. 3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit [DQ7]). 4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled Write AC Characteristics, and CE#-Controlled Write AC Characteristics. 70 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Write AC Characteristics Table 37: CE#-Controlled Write AC Characteristics Parameter 70ns VCCQ = VCC Symbol Legacy JEDEC Min Address valid to next address valid tWC tAVAV WE# LOW to CE# LOW tWS tWLEL CE# LOW to CE# HIGH tCP 80ns VCCQ = 1.65V to VCC Unit Max Min 75 - 85 - ns 0 - 0 - ns tELEH 35 - 35 - ns Input valid to CE# HIGH tDS tDVEH 45 - 45 - ns CE# HIGH to input transition tDH tEHDX 0 - 0 - ns CE# HIGH to WE# HIGH tWH tEHWH 0 - 0 - ns CE# HIGH to CE# LOW tCPH tEHEL 30 - 30 - ns Address valid to CE# LOW tAS tAVEL 0 - 0 - ns CE# LOW to address transition tAH tELAX 45 - 45 - ns - tGHEL 0 - 0 - ns OE# HIGH to CE# LOW CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 71 Max Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Write AC Characteristics Figure 21: CE#-Controlled Program AC Timing 3rd Cycle 4th Cycle Data Polling Read Cycle tWC tWC A[MAX:0] 555h PA PA tAH tAS tWH tWS WE# tOE tGHEL OE# tCP tCPH tE CE# tWHWH1 tDS DQ[15:0] AOh PD DQ7# tDF DOUT tOH DOUT tDH Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. Only the third and fourth cycles of the PROGRAM command are represented. The PROGRAM command is followed by checking of the status register data polling bit. 2. PA is the address of the memory location to be programmed. PD is the data to be programmed. 3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit [DQ7]). 4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled Write AC Characteristics, and CE#-Controlled Write AC Characteristics. 72 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Accelerated Program, Data Polling/Toggle AC Characteristics Accelerated Program, Data Polling/Toggle AC Characteristics Table 38: Accelerated Program and Data Polling/Data Toggle AC Characteristics Note 1 applies to the entire table. Symbol Parameter Legacy JEDEC Min Max Unit - tVHVPP 250 - ns Address setup time to OE# LOW during toggle bit polling tASO tAXGL 10 - ns Address hold time from OE# during toggle bit polling tAHT tGHAX, tEHAX 10 - ns CE# HIGH during toggle bit polling tEPH tEHEL2 10 - ns Output hold time during data and toggle bit polling tOEH tWHGL2, 20 - ns Program/erase valid to RY/BY# LOW tBUSY - 30 ns VPP/WP# rising or falling time tGHGL2 Note: tWHRL 1. Specifications apply to 70, and 80ns devices unless otherwise noted. Figure 22: Accelerated Program AC Timing VPP/WP# VPPH VIL or VIH tVHVPP CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 73 tVHVPP Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Accelerated Program, Data Polling/Toggle AC Characteristics Figure 23: Data Polling AC Timing tCH tE tHZ/tDF CE# tOE OE# tOEH WE# DQ7 Data DQ7# DQ7# Valid DQ7 Data DQ[6:0] Data Output flag Output flag Valid DQ[6:0] Data tBUSY RY/BY# Notes: 1. DQ7 returns a valid data bit when the PROGRAM or ERASE command has completed. 2. See the following tables for timing details: Read AC Characteristics, Accelerated Program and Data Polling/Data Toggle AC Characteristics. Figure 24: Toggle/Alternative Toggle Bit Polling AC Timing A[MAX:0]/ A-1 tAHT tASO CE# tOEH tAHT tASO WE# tOPH tEPH tOPH OE# tDH DQ6/DQ2 tCE tOE Data Toggle Toggle Toggle Stop toggling Output Valid tBUSY RY/BY# Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. DQ6 stops toggling when the PROGRAM or ERASE command has completed. DQ2 stops toggling when the CHIP ERASE or BLOCK ERASE command has completed. 2. See the following tables for timing details: Read AC Characteristics, Accelerated Program and Data Polling/Data Toggle AC Characteristics. 74 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Program/Erase Characteristics Program/Erase Characteristics Table 39: Program/Erase Characteristics Notes 1 and 2 apply to the entire table Parameter Min Typ Max - 145 - 125 Block erase (128 Kword) - Block erase (32 Kword) Chip erase Chip erase VPP/WP# = VPPH Erase suspend latency time 400 s 3 400 s 3 1 4 s 3, 4 - 0.37 1.5 s - 25 45 s - - s - 16 200 s 3 VPP/WP# = VPPH - 50 200 s 3 VPP/WP# = VIH Single-word program Write to buffer program (32 words at-a-time) Notes 50 Block erase timeout Word program Unit - 70 200 s 3 Chip program (word by word) - 270 400 s 3 Chip program (write to buffer program) - 25 200 s 3, 6 Chip program (write to buffer program with VPP/WP# = VPPH) - 13 50 s 3, 5 Chip program (enhanced buffered program) - 15 60 s 5 Chip program (enhanced buffered program with VPP/WP# = VPP) - 10 40 s 5 Program suspend latency time - 5 15 s 100,000 - - cycles 20 - - years PROGRAM/ERASE cycles (per block) Data retention Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. Typical values measured at room temperature and nominal voltages and for not cycled devices. 2. Typical and maximum values are sampled, but not 100% tested. 3. Maximum value measured at worst case conditions for both temperature and VCC after 100,000 PROGRAM/ERASE cycles. 4. Block erase polling cycle time (see Data polling AC waveforms figure). 5. Intrinsic program timing, that means without the time required to execute the bus cycles to load the PROGRAM commands. 75 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Package Dimensions Package Dimensions Figure 25: 56-Pin TSOP - 14mm x 20mm 20.00 0.20 18.40 0.10 Pin #1 0.50 TYP 14.00 0.10 0.22 0.05 0.10 MIN/ 0.21 MAX 0.10 See Detail A 1.20 MAX 1.00 0.05 0.10 0.05 o 3/5 o 0.50 0.10 Detail A Notes: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. All dimensions are in millimeters. 2. For the lead width value of 0.22 0.05, there is also a legacy value of 0.15 0.05. 76 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Package Dimensions Figure 26: 64-Pin TBGA - 10mm x 13mm 10.00 0.10 1.50 TYP 7.00 TYP 3.00 TYP 0.50 TYP 7.00 TYP 0.50 TYP 13.00 0.10 0.10 MAX BALL "A1" 1.00 TYP 0.35 MIN/ 0.50 MAX 0.30 -0.10 +0.05 1.20 MAX Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 0.80 TYP 1. All dimensions are in millimeters. 77 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Package Dimensions Figure 27: 64-Ball Fortified BGA - 11mm x 13mm 0.80 TYP Seating plane 0.15 MAX 64X Ball A1 ID 8 7 6 5 4 3 2 1 3.00 TYP A B C 13.00 0.10 D 7.00 TYP E 0.50 TYP F G H 1.00 TYP 1.00 TYP 0.60 0.05 2.00 TYP 1.40 MAX 0.48 0.05 7.00 TYP 11.00 0.10 Note: CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 1. All dimensions are in millimeters. 78 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved. 256Mb: 3V Embedded Parallel NOR Flash Revision History Revision History Rev. B - 5/18 * Added Important Notes and Warnings section for further clarification aligning to industry standards Rev. A - 10/12 * Initial Micron brand release 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000 www.micron.com/products/support Sales inquiries: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. CCMTD-1725822587-2414 m29dw_256g.pdf - Rev. B 5/18 EN 79 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2012 Micron Technology, Inc. All rights reserved.