E3JU-XP4T-3 - Omron - Product.Network

General-Purpose Fiber-optic Sensor E3JU-X/XR

Compact Limit Switch Style with

Universal Power Supply

HFET output allows for solid state

switching of AC or DC

HUniversal AC/DC power supply

HChoose cable or connector types

HSensitivity adjustment standard on all

models

HWide selection of timing options

HUL/CE/CSA approved

HNEMA 4X, IP66 rated

Ordering Information

JAMPLIFIERS

Light source Infrared LED Red LED

Fiber-optic cable attachment E32-series large diameter fiber (4.75 mm) E32-series small diameter fiber (2.2 mm)

Output Connection Timer Part number

Relay 300-V cable No E3JU-XM4-3 E3JU--XRM4-3

600-V cable E3JU-XM4-6 E3JU--XRM4-6

300-V cable Yes E3JU-XM4T-3 E3JU-XRM4T-3

600-V cable E3JU-XM4T-6 E3JU-XRM4T-6

FET 300-V cable No E3JU-XP4-3 E3JU-XRP4-3

600-V cable E3JU-XP4-6 E3JU-XRP4-6

300-V cable Yes E3JU-XP4T-3 E3JU-XRP4T-3

600-V cable E3JU-XP4T-6 E3JU-XRP4T-6

Relay MiniChangeRNo E3JU-XM4-MN1 E3JU-XRM4-MN1

Connector Yes E3JU-XM4T-MN1 E3JU-XRM4T-MN1

FET MiniChangeRNo E3JU-XP4-MN1 E3JU-XRP4-MN1

Connector Yes E3JU-XP4T-MN1 E3JU-XRP4T-MN1

JACCESSORIES

Description Part number

Mounting bracket E39-LU1

E3JU-X/XR

Specifications

Part number E3JU-XRj4j-jE3JU-Xj4j-j

Supply voltage 24 to 240 VAC !10%, 50/60 Hz; 12 to 240 VDC, 10% max. peak-to-peak ripple

Power consumption (up to 264 VDC) Contact relay type 4.0 W max., solid state relay type 3.5 W max.

Required fiber-optic cables E32-series (2.2 mm dia. or 1 mm dia.

with E39-F9) (See Note.)

E32-UjB series (4.75 mm dia.)

Light source Red LED (660 mm) Infrared LED (950 mm)

Operation mode Light-ON/Dark-ON, switch selectable

Sensitivity Adjustable

Mutual interference protection Provided

Contact output Contact

Type SPDT relay

relay Max. load 3 A, 250 VAC; 30 VDC rated (p.f.=1)

Min. load 10 mA, 5 VDC minimum

Response time Models without timer and models set to NO Timer: 12 ms ON (6 ms typ.),

12 ms OFF (5 ms typ.);

Models with timer: 0.1 to 10 sec (adjustable).

Solid

Type Power MOSFET relay

state

Max. load 400 mA AC/DC (600 mA up to 40"C), 240 VAC., 100 VDC rated

Response time Models without timer and timer models set to No Timer: 8 ms ON, 12 ms OFF max.

Models with timer: 0.1 to 10 sec (adjustable).

Timer functions

(models with timer)

Type/range ON-delay, OFF-delay, ON/OFF delay, one-shot, delayed one-shot; switch select-

able/0.1 to 10 seconds

Circuit protection Output

short-circuit

Not provided

Indicators Light incident (red LED), output operation (yellow LED), stability (green LED)

Materials Case Plastic ABS/PC

Holder Plastic ABS/PC

Clamp Plastic POM

Cover Plastic PC

Mounting Two M5 front-mounting through holes. M30 externally threaded base and 1/2-14

NPSM internal threads for cable type: conduit torque not to exceed 100 in-lbs.

Connections Prewired (--6) 600 V-rated, AWG 20: 4-wire cable, AWG 21: 5-wire cable or

(--3) 300 V-rated, AWG 22: 4-wire, 5-wire cables

Connector MiniChangeRtype connector: 4 and 5 pins

Weight Cable type (--6): 305 g (10.68 oz); (--3): 225 g (7.88 oz)

Connector type 135 g (4.73 oz)

Enclosure ratings UL Type 1

NEMA 1, 2, 3, 4X, 5, 12

IEC 144 IP66

Approvals UL Listing E41515

CSA Certification LR45951

CE IEC947-5-2

Ambient temperature Operating -25"Cto55"C(-13"F to 131"F)

Storage -40"Cto70"C(-40"F to 158"F)

Note: Must use fiber that can be inserted 15 mm into amplifier to meet sensing distance specification.

E3JU-X/XR E3JU-X/XR

Nomenclature

JSENSOR WITHOUT TIMER

E3JU-jjj4-j

JSENSOR WITH TIMER

E3JU-jjj4T-j

E3JU-X/XR

eration

JOUTPUT CIRCUIT DIAGRAMS

Solid State Relay Output Types

E3JU-jjPjj-j

Relay Output Types

E3JU-jjMjj-j

Main

circuit

Load*

Power

supply

Main

circuit

Load*

Power

supply

Power

supply

COM

Relay output

24 to 240 VAC

12 to 240 VDC

(50/60 Hz AC)

Either polarity

250 VAC, 3 A rated

5VDC,10mAmin.

24 to 240 VAC

12 to 240 VDC

(50/60 Hz AC)

Either polarity

0.1 to 400 mA

* Load can be hooked up on either

side of the power supply.

Line voltage

5 to 240 VAC

5to100VDC

Either polarity

Optically

isolated

JCONNECTIONS

Relay Output Types

E3JU-jjMjj-3

E3JU-jjMjj-6

Solid State Relay Output Types

E3JU-jjPjj-3

E3JU-jjPjj-6

Brown

Blue

Brown

Blue

Power

COM

Power

White Load

Black

Power

Relay Output Types

E3JU-jjMjj-MN1

Solid State Relay Output Types

E3JU-jjPjj-MN1

COM

Power

24 to 240 VAC

12 to 240 VDC

24 to 240 VAC

12 to 240 VDC

24 to 240 VAC

12 to 240 VDC

24 to 240 VAC

12 to 240 VDC

* Load can be hooked up on either side

of the power supply.

Load*

Load

Gray

Black

White

Power

Load*

E3JU-X/XR E3JU-X/XR

JTIMING CHART

E3JU-X/XR

JSENSITIVITY ADJUSTMENT

#Place the target object in the desired position for

detection and set the sensitivity adjustment to maximum.

#Maximum stability is achieved by varying both horizontal

and vertical alignment of the fiber until it is in the center of

a range in which both the LIGHT (Red) and STABILITY

(Green) indicators illuminate (Light-ON mode).

#Remove the object and ensure the LIGHT indicator turns

off and the STABILITY indicator illuminates. If the LIGHT

indicator does not turn off, decrease the sensitivity and

check that there is no other object in line with the fiber.

#Ensure the STABILITY indicator illuminates in both

detecting and non-detecting states. (Refer to table below.)

#Turn the sensitivity adjustment to maximum.

#Position the fiber optic cable ends opposite each other and

adjust the horizontal and vertical alignment until the

STABILITY indicator (Green), LIGHT indicator (Red), and

OUTPUT indicator (Yellow) turn on (Light-ON mode).

#Once the desired position is set, introduce the object to the

beam pattern and ensure that the LIGHT and OUTPUT

indicators turn off and the STABILITY indicator illuminates.

#If the LIGHT and OUTPUT indicators do not turn off,

decrease the sensitivity until the desired result is achieved.

#Ensure that the STABILITY indicator illuminates in both

detecting and non-detecting states. (Refer to table below.)

Through-beamDiffuse

Object

Object Indicators

Light

(Red) ON OFF

Incident

Stability

(Green) ON

ON OFF

Output

(Yellow)

Interrupt

LED Status (Light-ON Mode)

Diffuse Reflective Type Through-beam Type

JFIBER CONNECTION AND DISCONNECTION

#Uses E32 series fiber-optic cable with grooved tip

(4.75 mm diameter).

#Make sure the clamp is raised in the unlocked position.

#Firmly insert the fiber-optic cable tips into the amplifier.

#Move the clamp down to the locked position (the ridges in

the clamp should slide into the grooves of the tips and

hold the fiber cables in place).

#To remove the fiber cables, raise the clamp to the

unlocked position and carefully pull the fiber cables out

of the unit.

E3JU-Xj4j-j

#Uses E32 series fiber-optic cable (2.2 mm diameter or

1 mm diameter with E39-F9 adapter).

#Make sure the clamp is placed in the unlocked position

#Carefully insert the fiber cable into the amplifier, approxi-

mately 14.0 mm (0.55 in).

Caution: The amplifier may be damaged if excessive force is

used when inserting the fiber cables.

#Rotate the clamp to the locked position to secure the fiber

cables in place.

#To remove the fiber cables, rotate the clamp to the

unlocked position and carefully pull the fiber cables out

of the unit.

E3JU-XRj4j-j

E3JU-X/XR E3JU-X/XR

Dimensions

Unit: mm (inch)

JAMPLIFIERS

E3JU-XRjjj-j

E3JU-Xjjj-j

E3JU-X/XR

JMOUNTING BRACKET

E39-LU1 (Order Separately)

90"

61.0 (2.4)

35.6 (1.4)

30.7

(1.21) dia.

71.1 (2.8) 50.8 (2.0)

90"!0.5"

3.0 (0.119)

61.0 (2.4)

7.1

(0.28)

7.1 (0.28)

35.6

(1.4)

rad.

30.7

(1.21) dia.

50.8

(2.00) dia.

53.3 (2.1)

35.6 (1.4)

15.2 (0.6)

E3JU-X/XR E3JU-X/XR

MiniChange Connector

JBRAD HARRISON MINICHANGERCONNECTOR CABLES

Connector type Applicable sensors Length Straight Right angle

5-pole female connectors E3JU-jM4j-MN1 6 foot 41307 41307-90

12 foot 41308 41308-90

20 foot 41322 41322-90

4-pole female connectors E3JU-jP4j-MN1 6 foot 41108 41111-90

12 foot 41109 41112-90

20 foot 41177 41177-90

Note: The above part numbers represent Brad Harrison (Daniel Woodhead) part numbers not Omron part numbers. Please contact your

local Omron distributor for future availability by Omron and other equivalent Connector Cables.

Precautions

WARNING

These photoelectric sensors should not be used in personal

safety applications. Using the sensor as a safety device may

cause an unsafe condition that could lead to serious injury or

death.

CAUTION

Cover Screw Torque:

The torque of the cover screw must not exceed 3.5 kgScm

(3 inSlb). Over-torquing twill cause the plastic parts to crack.

JHIGH-VOLTAGE LINES

Do not place sensor power supply or signal lines within the same

conduit as high-voltage power lines.

JVOLTAGE RATINGS

Do not exceed rated supply voltage, ripple percent (for DC

models), or load current limits.

JAMBIENT LIGHTING

Do not install sensor in direct sunlight, or other sources of strong

ambient light.

JENVIRONMENTAL CONDITIONS

Do NOT install sensor in areas with any of these conditions:

#High humidity, or where condensation would result.

#Corrosive gas.

#High vibration or shock.

JPOWER SUPPLY

If a switching power supply is used, or when using with an

inverter or servomotor, ground the FG (frame ground) and

G (ground) terminals on the power supply for proper operation to

avoid damaging the sensor.

JWATER EXPOSURE

Do not use the sensor where it may be immersed, is outdoors, or

exposed to rain.

JPROPER MOUNTING SCREWS

Use M5 screws and washers to mount sensor and bracket.

JMECHANICAL SHOCK

Avoid mechanical shock during installation which may damage

the housing (see mechanical shock specifications).

JCONNECTOR

#When connecting or disconnecting the connector, hold the

connector cover to avoid tension on housing.

#Tighten connector only by hand. Do not use tools, which may

damage the connector.

#Always disconnect power before connecting or disconnecting

the connector.

#Be sure that the connector is tightened securely. If this is not

done, the sensor enclosure rating may be reduced, or the

connector may loosen and affect the enclosure rating.

C:/CEDSAX4

E3JU-X/XR

Cat. No. E01SAD3 04/02 Specifications subject to change without notice. Printed in U.S.A.

OMRON ELECTRONICS LLC

One East Commerce Drive

Schaumburg, IL 60173

NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.

1-800-55-OMRON

OMRON CANADA, INC.

885 Milner Avenue

Scarborough, Ontario M1B 5V8

416-286-6465

OMRON ON--LINE

Global -- http://www.omron.com

USA -- http://www.omron.com/oei

Canada -- http://www.omron.com/oci