LM4731 LM4731 Stereo 25W Audio Power Amplifier with Mute and Standby Modes Literature Number: SNAS197B LM4731 Stereo 25W Audio Power Amplifier with Mute and Standby Modes General Description Key Specifications The LM4731 is a stereo audio amplifier capable of delivering typically 25W per channel of continuous average output power into a 4 or 8 load with less than 10% THD+N from 20Hz - 20kHz. Each amplifier has an independent smooth transition fade-in/ out mute and a power conserving standby mode which can be controlled by external logic. The LM4731 has short circuit protection and a thermal shut down feature that is activated when the die temperature exceeds 150C. The LM4731 also has a under voltage lock out feature for click and pop free power off and on. The LM4731 has a wide operating supply range from +/-10V - +/-28V allowing for lower cost unregulated power supplies to be used. Output Power into 4 or 8, 10% THD+N THD+N at 1kHz with 2 x 1W into 8 25W (typ) 0.02% (typ) Mute Attenuation 85dB (typ) PSRR with fRIPPLE = 120Hz, 50dB (typ) VRIPPLE = 1VRMS Slew Rate 18V/s (typ) Standby Current (+/-22V) 4.8mA (typ) Features Minimal amount of external components necessary Quiet fade-in/out mute mode Low current Standby-mode Applications Audio amplifier for high-end stereo TVs Audio amplifier for component stereo Audio amplifier for compact stereo Audio amplifier for PC satellite speaker systems Audio amplifier for self powered speakers Connection Diagrams Plastic Package TO-220 Top Marking (Note 12) 20060375 20060352 Top View Non-Isolated Package Order Number LM4731TA See NS Package Number TA15A (c) 2011 National Semiconductor Corporation Top View U - Wafer Fab Code Z - Assembly Plant Code XY - Date Code TT - Die Traceability LM4731TA - LM4731TA 200603 200603 Version 3 Revision 12 www.national.com Print Date/Time: 2011/09/24 08:30:19 LM4731 Stereo 25W Audio Power Amplifier with Mute and Standby Modes OBSOLETE September 24, 2011 LM4731 Typical Application 20060353 FIGURE 1. Typical Audio Amplifier Application Circuit www.national.com 2 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage |V+| + |V-| Common Mode Input Voltage Differential Input Voltage Output Current Power Dissipation (Note 3) ESD Susceptability (Note 4) ESD Susceptability (Note 6) 56V V+ or V56V Internally Limited 50W 2.0kV 250V Electrical Characteristics 150C 260C -40C to +150C JA (TA) 43C/W JC (TA) 1.5C/W Operating Ratings (Note 1, Note 2) Temperature Range TMIN TA TMAX Supply Voltage |V+| + |V-| -20C TA +85C 20V VTOTAL 56V (Note 1, Note 2) The following specifications apply for V+ = +22V, V- = -22V and RL = 8 unless otherwise specified. Limits apply for TA = 25C. LM4731 Symbol Parameter Conditions |V+| + |V-| Power Supply Voltage (Note 10) AM Mute Attenuation GND - V- 9V |V+| = |V-| = 22V, RL = 8 Output Power (RMS) THD+N = 1% (max), f = 1kHz |V+| = |V-| =18V, RL = 4 |V+| = |V-| = 22V, RL = 8 THD+N Limit (Note 7) (Note 8) Units (Limits) 20 56 V (min) V (max) 85 THD+N = 10% (max), f = 1kHz |V+| = |V-| = 18V, RL = 4 PO Typical (Note 6) Total Harmonic Distortion + Noise dB 25 25 20 22 W (min) W (min) 20 20 18 18 W (min) W (min) 0.03 0.02 0.5 0.3 % (max) % (max) PO = 1W, f = 1kHz AV = 26dB, |V+| = |V-| = 18V, RL = 4 |V+| = |V-| = 22V, RL = 8 Xtalk Channel Separation PO = 10W f = 1kHz f = 10kHz 65 60 dB dB SR Slew Rate (Note 11) VIN = 2.0Vp-p, trise = 2ns 18 V/s IDD Total Quiescent Power Supply Current VCM = 0V, VO = 0V, IO = 0A Standby off (Play Mode) Standby on (Standby Mode) 95 4.8 110 6 mA (max) mA (max) VOS Input Offset Voltage VCM = 0V, IO = 0 mA 2.0 15 mV (max) IB Input Bias Current VCM = 0V, IO = 0 mA 0.2 A PSRR Power Supply Rejection Ratio VRIPPLE = 1VRMS, fRIPPLE = 120Hz sine wave Inputs terminated to GND 50 dB AVOL Open Loop Voltage Gain RL = 2 k, VO = 20V 110 dB eIN Input Noise IHF -- A-Weighting Filter 2.0 8 V (max) 0.8 V (max) 2.5 V (min) RIN = 600 (Input Referred) Standby VIL Standby Low Input Voltage Not in Standby Mode (Play) VIH Standby High Input Voltage In Standby Mode 2.0 3 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 Junction Temperature (TJMAX) (Note 9) Soldering Information T Package (10 sec.) Storage Temperature Thermal Resistance Absolute Maximum Ratings (Note 1, Note LM4731 LM4731 Symbol Parameter Conditions Mute VIL Mute Low Input Voltage Not in Mute Mode (Play) VIH Mute High Input Voltage In Mute Mode Typical (Note 6) 2.0 Limit (Note 7) (Note 8) Units (Limits) 0.8 V (max) 2.5 V (min) Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given. However, the typical value is a good indication of a device's performance. Note 3: The maximum power dissipation must be de-rated at elevated temperatures and is dictated by TJMAX, JC, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX -TA) / JC or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4731, TJMAX = 150C and the typical JC is 1.5C/W for the TA15A package . Refer to the Thermal Considerations section for more information. Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Note 5: Machine Model: a 220pF - 240pF discharged through all pins. Note 6: Typical specifications are sepcified at 25C and represent the parametric norm. Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: The operating junction temperature maximum is 150C. However, the instantaneous Safe Operating Area temperature is 250C. Note 10: V- must have at least -9V at its pin with reference to GND in order for the under-voltage protection circuitry to be disabled. In addition, the voltage differential between V+ and V- must be greater than 14V. Note 11: The feedback compensation network limits the bandwidth of the closed-loop response causing the skew rate to be reduced by the high frequency rolloff. Without feedback compensation the slew rate is typically larger. Note 12: The LM4731TA package TA15A is a non-isolated package setting the tab of the device and the heat sink to V-potential when the LM4731TA is directly mounted to the heat sink using only thermal compound. If a mica washer is used in addition to thermal compound, CS (case to sink) is increased, but the heat sink will be electrically isolated from V-. Bridged Amplifier Application Circuit 20060305 FIGURE 2. Bridged Amplifier Application Circuit www.national.com 4 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 LM4731 Single Supply Application Circuit 20060306 FIGURE 3. Single Supply Amplifier Application Circuit Note: *Optional components dependent upon specific design requirements. Auxiliary Amplifier Application Circuit 20060307 FIGURE 4. Special Audio Amplifier Application Circuit 5 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 External Components Description ( See Figures 1 - 4 ) Components Functional Description 1 RB Prevents currents from entering the amplifier's non-inverting input which may be passed through to the load upon power down of the system due to the low input impedance of the circuitry when the undervoltage circuitry is off. This phenomenon occurs when the supply voltages are below 1.5V. 2 Ri Inverting input resistance to provide AC gain in conjunction with Rf. 3 Rf Feedback resistance to provide AC gain in conjunction with Ri. 4 Ci (Note 13) Feedback capacitor which ensures unity gain at DC. Also creates a highpass filter with Ri at fC = 1/(2RiCi). 5 CS Provides power supply filtering and bypassing. Refer to the Supply Bypassing application section for proper placement and selection of bypass capacitors. 6 RV (Note 13) Acts as a volume control by setting the input voltage level. 7 RIN (Note 13) Sets the amplifier's input terminals DC bias point when CIN is present in the circuit. Also works with CIN to create 8 CIN (Note 13) Input capacitor which blocks the input signal's DC offsets from being passed onto the amplifier's inputs. 9 RSN (Note 13) Works with CSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. 10 CSN (Note 13) Works with RSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. The 11 12 L (Note 13) R (Note 13) Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and pass audio signals to the load. Refer to Figure 4. 13 RA Provides DC voltage biasing for the transistor Q1 in single supply operation. 14 CA Provides bias filtering for single supply operation. 15 RINP (Note 13) Limits the voltage difference between the amplifier's inputs for single supply operation. Refer to the Clicks and Pops application section for a more detailed explanation of the function of RINP. 16 RBI Provides input bias current for single supply operation. Refer to the Clicks and Pops application section for a more detailed explanation of the function of RBI. 17 RE Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the halfsupply point along with CA. a highpass filter at fC = 1/(2RINCIN). Refer to Figure 4. pole is set at fC = 1/(2RSNCSN). Refer to Figure 4. Note 13: Optional components dependent upon specific design requirements. www.national.com 6 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 LM4731 Typical Performance Characteristics Supply Current vs Supply Voltage PSRR vs Frequency 22V, VRIPPLE = 1VRMS, RL = 8, 80kHz BW 20060368 20060365 THD+N vs Frequency 18V, PO = 1W/Channel, RL = 4, 80kHz BW THD+N vs Frequency 22V, PO = 1W/Channel, RL = 8, 80kHz BW 20060369 20060370 7 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 THD+N vs Output Power 18V, RL = 4, 80kHz BW THD+N vs Output Power 22V, RL = 8, 80kHz BW 20060371 20060372 Output Power vs Supply Voltage f = 1kHz, RL = 4, 80kHz BW Output Power vs Supply Voltage f = 1kHz, RL = 8, 80kHz BW 20060363 20060364 Power Dissipation vs Output Power 1% THD (max), RL = 8, 80kHz BW Power Dissipation vs Output Power 1% THD (max), RL = 4, 80kHz BW 20060361 www.national.com 20060362 8 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 LM4731 Crosstalk vs Frequency 18V, PO = 10W, RL = 4, 80kHz BW Crosstalk vs Frequency 22V, PO = 10W, RL = 8, 80kHz BW 20060373 20060374 Mute Attenuation vs Mute Pin Voltage 22V, PO = 1W, RL = 8, 80kHz BW Standby Attenuation vs Standby Pin Voltage 22V, PO = 1W, RL = 8, 80kHz BW 20060360 20060366 Supply Current vs Standby Pin Voltage 22V 20060367 9 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 DETERMlNlNG MAXIMUM POWER DISSIPATION Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect maximum power dissipation calculation may result in inadequate heat sinking causing thermal shutdown and thus limiting the output power. Equation (1) exemplifies the theoretical maximum power dissipation point of each amplifier where VCC is the total supply voltage. Application Information MUTE MODE By placing a logic-high voltage on the mute pins, the signal going into the amplifiers will be muted. If the mute pins are left floating or connected to a logic-low voltage, the amplifiers will be in a non-muted state. There are two mute pins, one for each amplifier, so that one channel can be muted without muting the other if the application requires such a configuration. Refer to the Typical Performance Characteristics section for curves concerning Mute Attenuation vs Mute Pin Voltage. PDMAX = VCC2/22RL STANDBY MODE The standby mode of the LM4731 allows the user to drastically reduce power consumption when the amplifiers are idle. By placing a logic-high voltage on the standby pins, the amplifiers will go into Standby Mode. In this mode, the current drawn from the VCC supply is typically less than 10 A total for both amplifiers. The current drawn from the VEE supply is typically 4.8mA. Clearly, there is a significant reduction in idle power consumption when using the standby mode. There are two Standby pins, so that one channel can be put in standby mode without putting the other amplifier in standby if the application requires such flexibility. Refer to the Typical Performance Characteristics section for curves showing Supply Current vs. Standby Pin Voltage for both supplies. DETERMINING THE CORRECT HEAT SINK The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry does not operate under normal circumstances. The thermal resistance from the die (junction) to the outside air (ambient) is a combination of three thermal resistances, JC, CS, and SA. In addition, the thermal resistance, JC (junction to case), of the LM4731TA is 1.5C/W. Using Thermalloy Thermacote thermal compound, the thermal resistance, CS (case to sink), is about 0.2C/W. Since convection heat flow (power dissipation) is analogous to current flow, thermal resistance is analogous to electrical resistance, and temperature drops are analogous to voltage drops, the power dissipation out of the LM4731 is equal to the following: UNDER-VOLTAGE PROTECTION Upon system power-up, the under-voltage protection circuitry allows the power supplies and their corresponding capacitors to come up close to their full values before turning on the LM4731 such that no DC output spikes occur. Upon turn-off, the output of the LM4731 is brought to ground before the power supplies such that no transients occur at power-down. OVER-VOLTAGE PROTECTION The LM4731 contains over-voltage protection circuitry that limits the output current while also providing voltage clamping, though not through internal clamping diodes. The clamping effect is quite the same, however, the output transistors are designed to work alternately by sinking large current spikes. PDMAX = (TJMAX-TAMB)/JA SA = [(TJMAX-TAMB)-PDMAX(JC +CS)]/PDMAX (3) Again it must be noted that the value of SA is dependent upon the system designer's amplifier requirements. If the ambient temperature that the audio amplifier is to be working under is higher than 25C, then the thermal resistance for the heat sink, given all other things are equal, will need to be smaller. SUPPLY BYPASSING The LM4731 has excellent power supply rejection and does not require a regulated supply. However, to improve system performance as well as eliminate possible oscillations, the LM4731 should have its supply leads bypassed with low-inductance capacitors having short leads that are located close to the package terminals. Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as "motorboating" or by high frequency instabilities. These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10 F or larger) which is used to absorb low frequency variations and 10 200603 Version 3 Revision 12 (2) where TJMAX = 150C, TAMB is the system ambient temperature and JA = JC + CS + SA. Once the maximum package power dissipation has been calculated using equation (1), the maximum thermal resistance, SA, (heat sink to ambient) in C/W for a heat sink can be calculated. This calculation is made using equation (3) which is derived by solving for SA in equation (2). THERMAL PROTECTION The LM4731 has a sophisticated thermal protection scheme to prevent long-term thermal stress of the device. When the temperature on the die exceeds150C, the LM4731 shuts down. It starts operating again when the die temperature drops to about 145C, but if the temperature again begins to rise, shutdown will occur again above 150C. Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 150C and 145C. This greatly reduces the stress imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. Since the die temperature is directly dependent upon the heat sink used, the heat sink should be chosen such that thermal shutdown will not be reached during normal operation. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device, as discussed in the Determining the Correct Heat Sink Section. www.national.com (1) Thus by knowing the total supply voltage and rated output load, the maximum power dissipation point can be calculated. The package dissipation is twice the number which results from equation (1) since there are two amplifiers in each LM4731. Refer to the graphs of Power Dissipation versus Output Power in the Typical Performance Characteristics section which show the actual full range of power dissipation not just the maximum theoretical point that results from equation (1). Print Date/Time: 2011/09/24 08:30:19 LM4731 a small ceramic capacitor (0.1 F) to prevent any high frequency feedback through the power supply lines. If adequate bypassing is not provided, the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry. This signal causes distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470 F or more. BRIDGED AMPLIFIER APPLICATION The LM4731 has two operational amplifiers internally, allowing for a few different amplifier configurations. One of these configurations is referred to as "bridged mode" and involves driving the load differentially through the LM4731's outputs. This configuration is shown in Figure 2. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a distinct advantage over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Consequently, theoretically four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. For each operational amplifier in a bridge configuration, the internal power dissipation will increase by a factor of two over the single ended dissipation. Thus, for an audio power amplifier such as the LM4731, which has two operational amplifiers in one package, the package dissipation will increase by a factor of four. To calculate the LM4731's maximum power dissipation point for a bridged load, multiply equation (1) by a factor of four. This value of PDMAX can be used to calculate the correct size heat sink for a bridged amplifier application. Since the internal dissipation for a given power supply and load is increased by using bridged-mode, the heatsink's SA will have to decrease accordingly as shown by equation (3). Refer to the section, Determining the Correct Heat Sink, for a more detailed discussion of proper heat sinking for a given application. 20060354 FIGURE 5. Level Shift Circuit When the voltage at the Logic Input node is 0V, the 2N3904 is "off" and thus resistor Rc pulls up mute or standby input to the supply. This enables the mute or standby function. When the Logic Input is 5V, the 2N3904 is "on" and consequently, the voltage at the collector is essentially 0V. This will disable the mute or standby function, and thus the amplifier will be in its normal mode of operation. Rshift, along with Cshift, creates an RC time constant that reduces transients when the mute or standby functions are enabled or disabled. Additionally, Rshift limits the current supplied by the internal logic gates of the LM4731 which insures device reliability. Refer to the Mute Mode and Standby Mode sections in the Application Information section for a more detailed description of these functions. CLICKS AND POPS In the typical application of the LM4731 as a split-supply audio power amplifier, the IC exhibits excellent "click" and "pop" performance when utilizing the mute and standby modes. In addition, the device employs Under-Voltage Protection, which eliminates unwanted power-up and power-down transients. The basis for these functions are a stable and constant halfsupply potential. In a split-supply application, ground is the stable half-supply potential. But in a single-supply application, the half-supply needs to charge up just like the supply rail, VCC. This makes the task of attaining a clickless and popless turn-on more challenging. Any uneven charging of the amplifier inputs will result in output clicks and pops due to the differential input topology of the LM4731. To achieve a transient free power-up and power-down, the voltage seen at the input terminals should be ideally the same. Such a signal will be common-mode in nature, and will be rejected by the LM4731. In Figure 3, the resistor RINP serves to keep the inputs at the same potential by limiting the voltage difference possible between the two nodes. This should significantly reduce any type of turn-on pop, due to an uneven charging of the amplifier inputs. This charging is based on a specific application loading and thus, the system designer may need to adjust these values for optimal performance. As shown in Figure 3, the resistors labeled RBI help bias up the LM4731 off the half-supply node at the emitter of the 2N3904. But due to the input and output coupling capacitors in the circuit, along with the negative feedback, there are two different values of RBI, namely 10 k and 200 k. These resistors bring up the inputs at the same rate resulting in a popless turn-on. Adjusting these resistors values slightly may reduce pops resulting from power supplies that ramp extremely quick or exhibit overshoot during system turn-on. SINGLE-SUPPLY AMPLIFIER APPLICATION The typical application of the LM4731 is a split supply amplifier. But as shown in Figure 3, the LM4731 can also be used in a single power supply configuration. This involves using some external components to create a half-supply bias which is used as the reference for the inputs and outputs. Thus, the signal will swing around half-supply much like it swings around ground in a split-supply application. Along with proper circuit biasing, a few other considerations must be accounted for to take advantage of all of the LM4731 functions. The LM4731 possesses a mute and standby function with internal logic gates that are half-supply referenced. Thus, to enable either the Mute or Standby function, the voltage at these pins must be a minimum of 2.5V above half-supply. In single-supply systems, devices such as microprocessors and simple logic circuits used to control the mute and standby functions, are usually referenced to ground, not half-supply. Thus, to use these devices to control the logic circuitry of the LM4731, a "level shifter," like the one shown in Figure 5, must be employed. A level shifter is not needed in a split-supply configuration since ground is also half-supply. 11 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 a input coupling capacitor RIN is needed to set the DC bias point on the amplifier's input terminal. The resulting -3dB frequency response due to the combination of CIN and RIN can be found from Equation (6) shown below: PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components is required to meet the design targets of an application. The choice of external component values that will affect gain and low frequency response are discussed below. The gain of each amplifier is set by resistors Rf and Ri for the non-inverting configuration shown in Figure 1. The gain is found by Equation (4) below: AV = 1 + Rf / Ri (V/V) fIN = 1 / (2RINCIN) (Hz) PHYSICAL IC MOUNTING CONSIDERATIONS Mounting of the TO-220 package to a heat sink must be done such that there is sufficient pressure from the mounting screw to insure good contact with the heat sink for efficient heat flow. Over tightening the mounting screw will cause the TO-220 package to warp reducing contact area with the heat sink. Less contact with the heat sink will increase the thermal resistance from the TO-220 package case to the heat sink (CS) resulting in higher operating die temperatures and possible unwanted thermal shut down activation. Extreme over tightening of the mounting screw will cause severe physical stress resulting in cracked die and catastrophic IC failure. The recommended maximum mounting screw torque is 40 inchlbs or 3.3 foot-lbs (4.5 newton-meter). Additionally, if the mounting screw is used to force the TO-220 package into correct alignment with the heat sink, package stress will be increased. This increase in package stress will result in reduced contact area with the heat sink increasing die operating temperature and possible catastrophic IC failure. (4) For best noise performance, lower values of resistors are used. A value of 1k is commonly used for Ri and then setting the value of Rf for the desired gain. For the LM4731 the gain should be set no lower than 10V/V and no higher than 50V/ V. Gain settings below 10V/V may experience instability and using the LM4731 for gains higher than 50V/V will see an increase in noise and THD. The combination of Ri with Ci (see Figure 1) creates a high pass filter. The low frequency response is determined by these two components. The -3dB point can be found from Equation (5) shown below: fi = 1 / (2RiCi) (Hz) (5) If an input coupling capacitor is used to block DC from the inputs as shown in Figure 4, there will be another high pass filter created with the combination of CIN and RIN. When using www.national.com 12 200603 Version 3 Revision 12 (6) Print Date/Time: 2011/09/24 08:30:19 LM4731 20060355 FIGURE 6. Reference PCB Schematic 13 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 LM4731 REFERENCE BOARD ARTWORK Composite View Silk Screen 20060356 20060357 Top Layer Bottom Layer 20060358 www.national.com 20060359 14 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 LM4731 BILL OF MATERIALS FOR REFERENCE PCB Symbol Value Toleranc e Type/Description RIN1, RIN2 47k 5% 1/4 Watt RB1, RB2 1k 1% 1/4 Watt RF1, RF2 20k 1% 1/4 Watt Ri1, Ri2 1k 1% 1/4 Watt RSN1, RSN2 4.7 5% 1/4 Watt RG 2.7 5% 1/4 Watt CIN1, CIN2 1F 10% Metallized Polyester Film Ci1, Ci2 47F 20% Electrolytic Radial / 35V CSN1, CSN2 0.1F 20% Monolithic Ceramic CV 0.1F 20% Monolithic Ceramic CM 10F 20% Electrolytic Radial / 16V CS1, CS2 0.1F 20% Monolithic Ceramic CS3, CS4 10F 20% Electrolytic Radial / 35V CS5, CS6 1,000F 20% Electrolytic Radial / 35V S1, S2 SPDT (on-on) Switch J1, J2 Non-switched PC Mount RCA Jack J4, J7, J8 PCB Banana Jack- BLACK J3, J5, J6, J9 PCB Banana Jack- RED U1 15 lead TO-220 Power Socket U2 LM340, 5V Fixed Regulator, TO-263 package (TS3B) 15 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 Comments www.national.com LM4731 Physical Dimensions inches (millimeters) unless otherwise noted Non-Isolated TO-220 15-Lead Package Order Number LM4731TA NS Package Number TA15A www.national.com 16 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 LM4731 Notes 17 200603 Version 3 Revision 12 Print Date/Time: 2011/09/24 08:30:19 www.national.com LM4731 Stereo 25W Audio Power Amplifier with Mute and Standby Modes Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com 200603 Version 3 Revision 12 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com Print Date/Time: 2011/09/24 08:30:19 National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated