M24C01-WMN3TG/W - STMicroelectronics, Inc.

September 2006 Rev 8 1/33

M24C16, M24C08

M24C04, M24C02, M24C01

16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit Serial I²C bus EEPROM

Feature summary

■Two-wire I²C serial interface

Supports 400kHz protocol

■Single supply voltage:

– 2.5 to 5.5V for M24Cxx-W

– 1.8 to 5.5V for M24Cxx-R

■Write Control input

■Byte and Page Write (up to 16 Bytes)

■Random and Sequential Read modes

■Self-timed programming cycle

■Automatic address incrementi ng

■Enhanced ESD/latch-up protection

■More than 1 million Write cycles

■More than 40-year data retention

■Packages

– ECOPACK® (RoHS compliant)

Table 1. Product list

Reference Part Number

M24C16 M24C16-W

M24C16-R

M24C08 M24C08-W

M24C08-R

M24C04 M24C04-W

M24C04-R

M24C02 M24C02-W

M24C02-R

M24C01 M24C01-W

M24C01-R

PDIP8 (BN)

SO8 (MN)

150 mil width

TSSOP8 (DW)

169 mil width

TSSOP8 (DS)

3x3mm² body size

UFDFPN8 (MB)

2x3mm² (MLP)

www.st.com

Contents M24C16, M24C08, M24C04, M24C02, M24C01

2/33

Contents

1 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Serial Clock (SCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Serial Data (SDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Chip Enable (E0, E1, E2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3.1 Write Control (WC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4 Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.1 Operating supply v oltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.4.2 Power-up and device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.3 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Device operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1 Start condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2 Stop condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.3 Acknowledge Bit (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4 Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5 Memory addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.6 Write operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.6.1 Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.6.2 Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.6.3 Minimizing system delays by polling on ACK . . . . . . . . . . . . . . . . . . . . . 15

3.7 Read operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.7.1 Random Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.7.2 Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.7.3 Sequential Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.7.4 Acknowledge in Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4 Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

M24C16, M24C08, M24C04, M24C02, M24C01 Conte nts

3/33

7 Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

List of tables M24C16, M24C08, M24C04, M24C02, M24C01

4/33

List of tables

Table 1. Product list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Table 2. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 3. Device select code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 4. Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table 5. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8

Table 6. Operating conditions (M24Cxx-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 7. Operating conditions (M24Cxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 8. DC characteristics (M24Cxx-W, Device Grade 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 9. DC characteristics (M24Cxx-W, Device Grade 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 10. DC characteristics (M24Cxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 11. AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 12. Input parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 13. AC characteristics (M24Cxx-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 14. AC characteristics (M24Cxx-R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 15. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, package mechanica l da ta . . . . . . . . . . . . 25

Table 16. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width,

package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table 17. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead

2x3mm², data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7

Table 18. TSSOP8 – 8 lead Thin Shrink Small Outline, package mechanical data . . . . . . . . . . . . . . 28

Table 19. TSSOP8 3x3mm² – 8 lead Thin Shrink Small Outline, 3x3mm² body size,

mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 20. Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 21. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

M24C16, M24C08, M24C04, M24C02, M24C0 1 List of figures

5/33

List of figures

Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 2. 8-pin package connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 3. Device select code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 4. Maximum RP value versus bus parasitic capacitance (C) for an I²C bus . . . . . . . . . . . . . . 9

Figure 5. I²C bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 6. Write mode sequen ce s with WC = 1 (data write inhibited) . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 7. Write mode sequen ce s with WC = 0 (data write enabled) . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 8. Write cycle polling flowchart using ACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 9. Read mode sequences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 10. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 11. AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 12. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, package outline. . . . . . . . . . . . . . . . . . . . 25

Figure 13. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, package outline . . . . . . 26

Figure 14. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead

2x3mm², outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 15. TSSOP8 – 8 lead Thin Shrink Small Outline, package outline. . . . . . . . . . . . . . . . . . . . . . 28

Figure 16. TSSOP8 3x3mm² – 8 lead Thin Shrink Small Outline, 3x3mm² body size,

package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 9

Summary description M24C16, M24C08, M24C04, M24C02, M24C01

6/33

1 Summary description

These I²C-compatible electrically erasable programmable memory (EEPROM) devices are

organized as 2048/1024/512/256/128 x 8 (M24C16, M24C08, M24C04, M24C02 and

M24C01).

In order to meet environment al requirements, ST offers these devices in ECOPACK®

packages.

ECOPACK® packages are Lead-free and RoHS compliant.

ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.

Figure 1. Logic diagram

I²C uses a two-wire serial interface, comprising a bi-directional data line and a clock line.

The devices carry a built-in 4-bit Device Type Identifier code (101 0) in accordance with the

I²C bus definition.

The device beha v es as a slave in the I²C protocol, with all memory operations synchronized

by the serial clock. Read and Write operations are initiated by a Star t condition, generated

by the bus master. The Start condition is followed by a Device Select Code and Read/Write

bit (RW) (as described in Table 3), terminated by an acknowledge bit.

When writing data to the memory, the device inserts an acknowle dge bit during the 9th bit

time, f ollowing the bus master’s 8-bit tr ansmission. When data is r ead by t he bu s master, the

bus master acknowledges the receipt of the data byte in the same way. Data transfers are

terminated by a Stop condition after an Ack for Write, and after a NoAck for Read.

Table 2. Signal names

E0, E1, E2 Chip Enable

SDA Serial Data

SCL Serial Clock

WC Write Control

VCC Supply Voltage

VSS Ground

AI02033

E0-E2 SDA

VCC

M24Cxx

SCL

VSS

M24C16, M24C08, M24C04, M24C02, M24C01 Summary description

7/33

Figure 2. 8-pin package connections (top view)

1. NC = Not Connected

2. See Section 7: Package mechanical for package dimensions, and how to identify pin-1.

SDAVSS SCL

VCC

/ E2

AI02034E

M24Cxx

/ E2/ E2/ E2NC / E1

/ E1/ E1/ NCNC / E0

/ E0/ NC/ NCNC /1Kb

/2Kb/4Kb/8Kb16Kb

Signal description M24C16, M24C08, M24C04, M24C02, M24C01

8/33

2 Signal description

2.1 Serial Clock (SCL)

This input signal is used to strobe all data in and out of the device . In applications where this

signal is used by slave devices to synchronize the bus to a slower clock, the bus master

must have an open drain output, and a pull-up resistor can be connected from Serial Clock

(SCL) to VCC. (Figure 4 indicates how the value of the pull-up resistor can be calculated). In

most applications, though, this method of synchronization is not employed, and so the pull-

up resistor is not n ecessary, provided that the bus master has a push-pull ( rather than open

drain) output.

2.2 Serial Data (SDA)

This bi-directional signal is used to transfer data in or out of the device. It is an open drain

output that may be wire-OR’ed with other open dr ain or ope n collector signa ls on the b u s . A

pull up resistor must be connected from Serial Data (SDA) to VCC. (Figure 4 indicates how

the value of the pull-up resistor can be calculated).

2.3 Chip Enable (E0, E1, E2)

These input signals are used to set the value that is to be looked for on the three least

significant bits (b3, b2, b1) of the 7-bit Device Select Code. These inputs must be tied to

VCC or VSS, to establish the Device Select Code as shown in Figure 3.

Figure 3. Device select code

2.3.1 Write Control (WC)

This input signal is useful for protecting the entire contents of the memory from inadvertent

write operations. Write operations are disabled to the entire memory array when Write

Control (WC) is driven High. When unconnected, the signal is internally read as VIL, and

Write ope ration s ar e allowed.

When Write Control (WC) is driven High, Device Select and Address b ytes are

acknowledged, Data bytes are not acknowledged.

Ai11650

VCC

M24Cxx

VSS

VCC

M24Cxx

VSS

M24C16, M24C08, M24C04, M24C02, M24C01 Sign al description

9/33

2.4 Supply voltage (VCC)

2.4.1 Operating supply voltage VCC

Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage

within the specified [VCC(min) , VCC(max)] range must be applied (see Table 6 and Table 7).

In order to secure a stable DC supply voltage, it is recommended to decouple the VCC line

with a suitable capacitor (usually of the order of 10nF to 10 0nF) close to the VCC/VSS

package pins.

This v oltage m ust remain st ab le and v a lid until the end of the tr an smission of the instruction

and, for a Write instruction, until the complet ion of the internal write cycle (tW).

The VCC rise time must not vary faster than 1V/µs

2.4.2 Power-up and device Reset

In order to prevent ina dvertent Write operations during Power-u p, a Power On Reset (POR)

circuit is included. At Pow er-up (cont inuous rise of V CC), the device does not respond to an y

instruction until V CC has reached the Power On Reset threshold voltage (this threshold is

lower than the minim um VCC operating voltage defined in Table 6 and Table 7).

When VCC has passed the POR threshold, the device is reset and in Standby Power mode.

2.4.3 Power-down

At Power-down (where VCC decreases continuously), as so on as VCC drops from the

operating voltage range to below the Power On Reset threshold voltage, the device stops

responding to any instruction sent to it.

During Power- do wn, the device must be desele cted an d in the Standby P o w er mode (that is

there should be no internal Write cycle in pr ogres s) .

Figure 4. Maximum RP value versus bus parasitic capacitance (C) for an I²C bus

AI01665b

VCC

SDA

MASTER

SCL C

100

C (pF)

Maximum RP value (kΩ)

10 1000

fc = 400kHz

fc = 100kHz

Signal description M24C16, M24C08, M24C04, M24C02, M24C01

10/33

Figure 5. I²C b us protocol

Table 3. Device select code

Device Type Identifier(1)

1. The most significant bit, b7, is sent first.

Chip Enable(2),(3)

2. E0, E1 and E2 are compared against the respective external pins on the memory device.

3. A10, A9 and A8 represent most significant bits of the address.

b7 b6 b5 b4 b3 b2 b1 b0

M24C01 Select Code1010E2E1E0RW

M24C02 Select Code1010E2E1E0RW

M24C04 Select Code1010E2E1A8RW

M24C08 Select Code1010E2A9A8RW

M24C16 Select Code1010A10A9A8RW

SCL

SDA

SCL

SDA

START

Condition

SDA

Input SDA

Change

AI00792B

STOP

Condition

123 789

MSB ACK

START

Condition

SCL 123 789

MSB ACK

STOP

Condition

M24C16, M24C08, M24C04, M24C02, M24C01 Device operation

11/33

3 Device operation

The device supports the I²C protocol. This is summarized in Figure 5. An y device that sends

data on to the bus is defined to be a transmitter, and any device that reads the data to be a

receiver. The device that controls the data transfer is known as the bus master, and the

other as the slave device. A data transfer can only be initiated by the bus master, which will

also pro vid e th e serial clock for synchro nization . The M2 4Cxx device is always a slave in all

communication.

3.1 Start condition

Start is identified by a falling edge of Serial Data (SDA) while Serial Clock (SCL) is stab le in

the High state. A Start condition must precede any data transfer command. The device

continuously monitors (except during a Write cycle) Serial Data (SDA) and Serial Clock

(SCL) for a Start condition, and will not respond unless one is given.

3.2 Stop condition

Stop is identified by a rising edge of Serial Data (SDA) while Serial Clock (SCL) is stable

and driven High. A Stop condition terminates communication between the device and the

bus m aster . A Read command that is follow ed b y NoAc k can be f ollo wed b y a Stop cond ition

to f orc e the device into the Stand-b y mode . A St op conditio n at the end of a Write command

triggers the internal Write cycle.

3.3 Acknowledge Bit (ACK)

The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter,

whether it be bus master or slav e device , releases Serial Data (SD A) after sending eight bits

of data. During the 9th clock pulse period, the receiver pulls Serial Data (SDA) Low to

acknowle dge the receipt of the eight da ta bits.

3.4 Data input

During data input, the device samples Serial Data (SDA) on the rising edge of Serial Clock

(SCL). F or correct de vice o peration, Serial Data (SDA) must be stab le during the rising edge

of Serial Clock (SCL), and the Serial Data (SD A) signal must change only when Serial Clock

(SCL) is driven Low.

Device opera ti on M24C16, M2 4C08, M24C04 , M2 4 C 0 2, M 24 C0 1

12/33

3.5 Memory addressing

To start communication between the bus master and the slave device, the bus master must

initiate a Start condition. Following this, the bus master sends the Device Select Code,

shown in Table 3 (on Serial Data (SDA), most significant bit first).

The Device Select Code consists of a 4-bit Device Type Identifier, and a 3-bit Chip Enable

“Address” (E2, E1, E0). To address the memory array, the 4-bit Device Type Identifier is

1010b.

Each device is given a unique 3- bit code on the Chip Enable (E0 , E1, E2) inp uts . Wh en the

Device Select Code is received, the device only responds if the Chip Enable Address is the

same as the value on the Chip Enable (E0, E1, E2) inputs. However, those devices with

larger memory capacities (the M24C1 6, M24C08 and M24C04) nee d more addr ess bits . E0

is not available f or use on devices that need to use address line A8; E1 is not av ailable for

devices that need to use address line A9, and E2 is not available for devices that need to

use address line A10 (see Figure 2 and Table 3 f or details). Using the E0, E1 and E2 in puts,

up to eight M2 4C02 (or M24C01), four M24C04, two M24C08 or one M24C16 devices can

be connected to one I²C bus. In each case, an d in the hybrid cases, this gives a total

memory capacity of 16 Kbits, 2 KBytes (except where M24C01 devices are used).

The 8th bit is the Read/Write bit (RW). This b it is set to 1 for Read and 0 for Write operations .

If a match occurs on the Device Select code, the corresponding device gives an

acknowledgment on Serial Data (SDA) during the 9th bit time. If the device does not match

the Device Select code, it deselects itself from the bus, and goes into Stand-by mode.

Table 4. Operating modes

Mode RW bit WC(1)

1. X = VIH or VIL.

Bytes Initial Sequence

Current Address Read 1 X 1 START, Device Select, RW = 1

Random Address Read 0X1START, Device Select, RW = 0, Address

1 X reSTART, Device Select, R W = 1

Sequential Read 1 X ≥ 1 Similar to Current or Random Address

Read

Byte Write 0 VIL 1 START, Device Select, RW = 0

Page Write 0 VIL ≤ 16 START, Device Select, RW = 0

M24C16, M24C08, M24C04, M24C02, M24C01 Device operation

13/33

Figure 6. Write mode sequences with WC = 1 (data write inhibited)

3.6 Write operations

F ollo wing a Start condition the b us master sends a Device Select Code with the Read/Write

bit (RW) reset to 0. Th e device acknowledges this, as shown in Figure 7, and waits for an

address byte. The device responds to the address byte with an acknowledge bit, and then

waits for th e da ta byte.

When the bus master generates a Stop condition immediately after the Ack bit (in the “10th

bit” time slot) , either at the end of a Byte Write or a Page Write, the internal Write cycle is

triggered. A Stop condition at any other time slot does not trigger the internal Write cycle.

During the internal Write cycle, Serial Data (SDA) and Serial Clock (SCL) are ignored, and

the device does not respond to any requests.

3.6.1 Byte Write

After the Device Select code and the address byte, the bus master sends one data byte. If

the addressed loc at i on is Write-protecte d, by Write Co ntr o l (WC ) being driven High (during

the period from the Start condition until the end of the address b yte), the device replies to

the data byte with NoAck, as shown in Figure 6, and the locati on is n ot modif ied. I f, instead,

the addressed location is not Write-protected, the device replies with Ack. The bus master

terminates the transfer by generating a Stop condition, as shown in Figure 7.

STOP

START

Byte Write DEV SEL BYTE ADDR DATA IN

START

Page Write DEV SEL BYTE ADDR DATA IN 1 DATA IN 2

DATA IN 3

AI02803C

Page Write

(cont'd)

WC (cont'd)

STOP

DATA IN N

ACK ACK NO ACK

R/W

ACK ACK NO ACK NO ACK

R/W

NO ACK NO ACK

Device opera ti on M24C16, M2 4C08, M24C04 , M2 4 C 0 2, M 24 C0 1

14/33

3.6.2 Page Write

The Page Write mode allows up to 16 bytes t o be written in a single Write cycle, provided

that they are all located in the same page in the memory: that is, the most significant

memory address bits are the same. If more bytes are sent than will fit up to the end of the

page, a condition known as ‘roll-over’ occurs. This should be avoided, as d ata starts to

become overwritten in an implementation dependent way.

The bus master sends from 1 to 16 bytes of data, each of which is acknowledged by the

device if Write Control (WC) is Low. If the addressed location is Write-protected, by Write

Control (WC) being driven High (during the period from the Start condition until the end of

the address byte), the device replies to the data bytes with NoAck, as shown in Figure 6,

and the locations are not modified. After each byte is transferred, the internal byte address

counter (the 4 least significan t address bits only) is incremented. The transfer is terminated

by the bus master generating a Stop condition.

Figure 7. Write mode sequences with WC = 0 (data write enabled)

STOP

START

BYTE WRITE DEV SEL BYTE ADDR DATA IN

START

PAGE WRITE DEV SEL BYTE ADDR DATA IN 1 DATA IN 2

DATA IN 3

AI02804B

PAGE WRITE

(cont'd)

WC (cont'd)

STOP

DATA IN N

ACK

R/W

ACK ACK

ACK ACK ACK ACK

R/W

ACKACK

M24C16, M24C08, M24C04, M24C02, M24C01 Device operation

15/33

Figure 8. Write cycle polling flowchart using ACK

3.6.3 Minimizing system delays by polling on ACK

During the internal Write cycle, the de vice d isconnect s itself fr om the b us , and writes a copy

of the data from its internal latches to the memory cells. The maximum Write time (tw) is

shown in Table 13 and Table 14, but the typical time is shorter . To make use of this, a polling

sequence can be used by the bus master.

The sequence, as shown in Figure 8, is :

●Initial condition: a Write cycle is in progress.

●Step 1: the bus master issues a Start condition followed by a Device Select Code (the

first byte of the new instruction).

●Step 2: if the device is busy with the internal Write cycle, no Ack will be returned and

the bus master goes bac k to Step 1. If the device has terminated the internal Write

cycle, it re sp onds wit h an Ack, indicating that th e d evice is ready to re ce ive the second

part of the instruction (the first byte of this instruction having been sent during Step 1).

WRITE Cycle

in Progress

AI01847C

Operation is

Addressing the

Memory

START Condition

DEVICE SELECT

with RW = 0

ACK

Returned

YES

YESNO

ReSTART

STOP

DATA for the

WRITE Operation DEVICE SELECT

with RW = 1

Send Address

and Receive ACK

First byte of instruction

with RW = 0 already

decoded by the device

YESNO START

Condition

Continue the

WRITE Operation Continue the

Random READ Operation

Device opera ti on M24C16, M2 4C08, M24C04 , M2 4 C 0 2, M 24 C0 1

16/33

Figure 9. Read mode sequences

1. The seven most significant bits of the Device Select Code of a Random Read (in the 1st and 3rd bytes)

must be identical.

3.7 Read operations

Read opera tions are performed independently of the state of the Write Control (WC) signal.

The device has an internal address counter which is incremented each time a byte is read.

3.7.1 Random Address Read

A dummy Write is firs t performed to load the ad dress into this a ddress co unter ( as sho wn in

Figure 9) but without sending a Stop condition. Then, the bus master sends another Start

condition, and repeats the Device Select Code, with the Read /Write bit (RW) set to 1. The

device acknowledg es this, and out puts the contents of the addressed byte. The bus master

must not acknowledge the byte, and terminates the transfer with a Stop condition.

START

DEV SEL * BYTE ADDR

START

DEV SEL DATA OUT 1

AI01942

DATA OUT N

STOP

START

CURRENT

ADDRESS

READ DEV SEL DATA OUT

RANDOM

ADDRESS

READ

STOP

START

DEV SEL * DATA OUT

SEQUENTIAL

CURRENT

READ

STOP

DATA OUT N

START

DEV SEL * BYTE ADDR

SEQUENTIAL

RANDOM

READ

START

DEV SEL * DATA OUT 1

STOP

ACK

R/W

NO ACK

ACK

R/W

ACK ACK

R/W

ACK ACK ACK NO ACK

R/W

NO ACK

ACK ACK

R/W

ACK ACK

R/W

ACK NO ACK

M24C16, M24C08, M24C04, M24C02, M24C01 Device operation

17/33

3.7.2 Current Address Read

F or the Current Address Read operation, f ollowing a Start condition, the bus master only

sends a Device Select Code with the Read/Write bit (RW) set to 1. The device

acknowledges this, and outputs the byte addressed by the internal address counter. The

counter is then incremented. The bus master terminates the transfer with a Stop condition,

as shown in Figure 9, without acknowledging the byte.

3.7.3 Sequential Read

This operation can be used af ter a Cu rren t Address Read or a Random Addr ess Read. The

bus master does acknowledge the data byte output, and sends additional clock pulses so

that the device continues to output the next byte in sequence. To term inate the stream of

bytes, t he bus mast er must not ackno wledge the last byte, and must generate a Stop

condition, as shown in Figure 9.

The output data comes from consecutive addresses, with the internal address counter

automatically incremented after each byte output. After the last memory address, the

address counter ‘rolls-over’, and the device continues to output data from memory address

00h.

3.7.4 Acknowledge in Read mode

For all Read commands, the device waits, after each byte read, for an acknowledgment

during the 9th bit ti me. If the bus maste r does not drive Serial Data (SDA) Low during this

time, the device terminates the data transfer and switches to its Stand-by mode.

Initial del ivery state M24C16, M24C0 8, M24C04, M24C02, M24C01

18/33

4 Initial delivery state

The device is delivered with all bits in the memory array set to 1 (each byte contains FFh).

5 Maximum rating

Stressing the device outside the ratings listed in Table 5 may cause permanent damage to

the device. These are stress ratings only, and operation of the de vice at these, or any other

conditions outside those indicated in the Operating sections of this specification, is not

implied. Exposure to Absolute Maximum Rating conditions for extended periods ma y aff ect

device reliability. Refer also to the STMicroelectronics SURE Program and other relevant

quality documents.

1. TLEAD max must not be applied for more than 10s.

2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114A, C1=100pF, R1=1500Ω, R2=500Ω).

Table 5. Absolute maximum ratings

Symbol Parameter Min. Max. Unit

TAAmbient Operating Temperature –40 130 °C

TSTG Storage Temperature –65 150 °C

TLEAD Lead Temperature during Soldering see note (1)

1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the ST ECOPACK®

7191395 specification, and the European directive on Restrictions on Hazardous Substances (RoHS)

2002/95/EU.

°C

PDIP-Specific Lead Temperature durin g Soldering 260(2)

2. TLEAD max must not be applied for more than 10s.

°C

VIO Input or Output range –0.50 6.5 V

VCC Supply Voltage –0.50 6.5 V

VESD Electrostatic Discharge Voltage (Human Body model)

(2) –4000 4000 V

M24C16, M24C08, M24C04, M24C02, M24C01 DC and AC parameters

19/33

6 DC and AC parameters

This section summarizes the operating and measurement conditions, and the DC and AC

characteristics of the device. The par ameters in the DC and AC Characteristic tables that

follow are derived from tests performed under the Measurement Conditions summarized in

the relevant tables. Designers should check that the operating conditions in their circuit

match the measurem ent conditions when relying on the quoted parameters.

Table 6. Operating conditions (M24Cxx-W)

Symbol Parameter Min. Max. Unit

VCC Supply Voltage 2.5 5.5 V

Ambient Operating Temperature (Device

Grade 6) –40 85 °C

Ambient Operating Temperature (Device

Grade 3) –40 125 °C

Table 7. Operating conditions (M24Cxx-R)

Symbol Parameter Min. Max. Unit

VCC Supply Voltage 1.8 5.5 V

TAAmbient Operating Temperature –40 85 °C

Table 8. DC characteristics (M24Cxx-W, Device Grade 6)

Symbol Parameter Test Condition

(in addition to those in Table 6)Min. Max. Unit

ILI Input Leakage Current

(SCL, SDA, E0, E1,and E2) VIN = VSS or VCC, device in

Standby mode ± 2 µA

ILO Output Leakage Current VOUT = VSS or VCC, SDA in Hi-Z ± 2 µA

ICC Supply Current

VCC=5V, fc=400kHz

(rise/fall time < 30ns) 2mA

VCC =2.5V, fc=400kHz

(rise/fall time < 30ns) 1mA

ICC1 Stand-by Supply Current VIN = VSS or VCC,

f or 2.5V < VCC = < 5.5V 1µA

VIL Input Low Voltage (1)

1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kΩ.

–0.45 0.3VCC V

VIH Input High Voltage (1) 0.7VCC VCC+1 V

VOL Output Low Voltage IOL = 2.1mA when VCC = 2.5V or

IOL = 3mA when VCC = 5.5V 0.4 V

DC and AC parameters M24C16, M24C08, M24C04, M24C02, M24C01

20/33

Table 9. DC characteristics (M24Cxx-W, Device Grade 3)

Symbol Parameter Test Condition

(in addition to those in Table 6)Min. Max. Unit

ILI Input Leakage Current

(SCL, SDA, E0, E1,and E2) VIN = VSS or VCC, device in

Standby mode ± 2 µA

ILO Output Leakage Current VOUT = VSS or VCC, SDA in Hi-Z ± 2 µA

ICC Supply Current

VCC=5V, fC=400kHz

(rise/fall time < 30ns) 3mA

VCC =2.5V, fC=400kHz

(rise/fall time < 30ns) 3mA

ICC1 Stand-by Supply Current VIN = VSS or VCC, VCC = 5 V 5 µA

VIN = VSS or VCC, VCC = 2.5 V 2 µA

VIL Input Low Voltage(1)

1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kΩ.

–0.45 0.3VCC V

VIH Input High Voltage(1) 0.7VCC VCC+1 V

VOL Output Low Voltage IOL = 2.1mA when VCC = 2.5V or

IOL = 3mA when VCC = 5.5V 0.4 V

Table 10. DC characteristics (M24Cxx-R)

Symbol Parameter Test Condition

(in addition to those in Table 7)Min. Max. Unit

ILI Input Leakage Current

(SCL, SD A, E0, E1,and E2) VIN = VSS or VCC, device in

Standby mode ± 2 µA

ILO Output Leakage Current VOUT = VSS or VCC, SDA in Hi-Z ± 2 µA

ICC Supply Current VCC =1.8V, fc=400kHz

(rise/fall time < 30ns) 0.8 mA

ICC1 Stand-by Supply Current VIN = VSS or VCC,

1.8V < VCC < 2.5V 1µA

VIL Input Low Voltage (1)

1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kΩ.

2.5 V ≤ VCC –0.45 0.3 VCC V

1.8 V ≤ VCC < 2.5V –0.45 0.25V

CC V

VIH Input High Voltage (1) 0.7VCC VCC+1 V

VOL Output Low Voltage IOL = 0.7 mA, VCC = 1.8 V 0.2 V

M24C16, M24C08, M24C04, M24C02, M24C01 DC and AC parameters

21/33

Figure 10. AC measurement I/O waveform

Table 11. AC measurement conditions

Symbol Parameter Min. Max. Unit

CLLoad Capacitance 100 pF

Input Rise and Fall Times 50 ns

Input Levels 0.2VCC to 0.8VCC V

Input and Output Timing Reference Levels 0.3VCC to 0.7VCC V

Table 12. Input parameters

Symbol Parameter(1),(2)

1. TA = 25°C, f = 400kHz

2. Sampled only, not 100% tested.

Test Condition Min. Max. Unit

CIN Input Capacitance (SD A) 8 pF

CIN Input Capacitance (other pins) 6 pF

ZWCL WC Input Impedance VIN < 0.3 V 15 70 kΩ

ZWCH WC Input Impedance VIN > 0.7VCC 500 kΩ

tNS Pulse width ignored

(Input Filter on SCL and SDA) Single glitch 100 ns

AI00825B

0.8VCC

0.2VCC

0.7VCC

0.3VCC

Input and Output

Timing Reference Levels

Input Levels

DC and AC parameters M24C16, M24C08, M24C04, M24C02, M24C01

22/33

Table 13. AC characteristics (M24Cxx-W)

Test conditions specified in Table 6 and Table 11

Symbol Alt. Parameter Min. Max. Unit

fCfSCL Clock Frequency 400 kHz

tCHCL tHIGH Clock Pulse Width High 600 ns

tCLCH tLOW Clock Pulse Width Low 1300 ns

tDL1DL2(1)

1. Sampled only, not 100% tested.

tFSDA F all Time 20 300 ns

tDXCX tSU:DAT Data In Set Up Time 100 ns

tCLDX tHD:DAT Data In Hold Time 0 ns

tCLQX tDH Data Out Hold Time 200 ns

tCLQV(2)

2. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the

falling or rising edge of SDA.

tAA Clock Low to Next Data Valid (Access Time) 200 900 ns

tCHDX(3)

3. For a reSTART condition, or following a Write cycle.

tSU:STA Start Condition Set Up Time 600 ns

tDLCL tHD:STA Start Condition Hold Time 600 ns

tCHDH tSU:STO Stop Condition Set Up Time 600 ns

tDHDL tBUF Time between Stop Condition and Next Start

Condition 1300 ns

tW(4)

4. Previous devices bearing the process letter “L” in the package marking guarantee a maximum write time of

10ms. For more information about these devices and their device identification, please ask your ST Sales

Office for Process Change Notices PCN MPG/EE/0061 and 0062 (PCEE0061 and PCEE0062).

tWR Write Time 5 ms

M24C16, M24C08, M24C04, M24C02, M24C01 DC and AC parameters

23/33

Table 14. AC characteristics (M24Cxx-R)

Test conditions specifie d in Table 7 and Table 10

Symbol Alt. Parameter Min. Max. Unit

fCfSCL Clock Frequency 400 kHz

tCHCL tHIGH Clock Pulse Width High 600 n s

tCLCH tLOW Clock Pulse Width Low 1300 ns

tDL1DL2(1)

1. Sampled only, not 100% tested.

tFSDA Fall Time 20 300 ns

tDXCX tSU:DAT Data In Set Up Time 100 ns

tCLDX tHD:DAT Data In Hold Time 0 ns

tCLQX tDH Data Out Hold Time 200 ns

tCLQV(2)

2. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the

falling or rising edge of SDA.

tAA Clock Low to Next Data Valid (Access Time) 200 900 ns

tCHDX(3)

3. For a reSTART condition, or following a Write cycle.

tSU:STA Start Condition Set Up Time 600 ns

tDLCL tHD:STA Start Condition Hold Time 600 ns

tCHDH tSU:STO Stop Condition Set Up Time 600 ns

tDHDL tBUF Time between Stop Condition and Next Start

Condition 1300 ns

tWtWR Write Time 10 ms

DC and AC parameters M24C16, M24C08, M24C04, M24C02, M24C01

24/33

Figure 11. AC waveforms

SCL

SDA In

SCL

SDA Out

SCL

SDA In

tCHCL

tDLCL

tCHDX

START

Condition

tCLCH

tDXCXtCLDX

SDA

Input

SDA

Change tCHDH tDHDL

STOP

Condition

Data Valid

tCLQV tCLQX

tCHDH

STOP

Condition

tCHDX

START

Condition

Write Cycle

AI00795C

START

Condition

M24C16, M24C08, M24C04, M24C02, M24C01 Package mechanical

25/33

7 Package mechanical

Figure 12. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, package outline

1. Drawing is not to scale.

Table 15. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, package mechanical data

Symbol millimeters inches

Typ. Min. Max. Typ. Min. Max.

A 5.33 0.210

A1 0.38 0.015

A2 3.30 2.92 4.95 0.130 0.115 0.195

b 0.46 0.36 0.56 0.018 0.014 0.022

b2 1.52 1.14 1.78 0.060 0.045 0.070

c 0.25 0.20 0.36 0.010 0.008 0.014

D 9.27 9.02 10.16 0.365 0.355 0.400

E 7.87 7.62 8.26 0.310 0.300 0.325

E1 6.35 6.10 7.11 0.250 0.240 0.280

e 2.54 – – 0.100 – –

eA 7.62 – – 0.300 – –

eB 10.92 0.430

L 3.30 2.92 3.81 0.130 0.115 0.150

PDIP-B

Package mecha n ic al M24C16, M2 4C08, M24C04 , M2 4 C 0 2, M 24C 0 1

26/33

Figure 13. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, package

outline

1. Drawing is not to scale.

2. The ‘1’ that appears in the top view of the package shows the position of pin 1 and the ‘N’ indicates the total

number of pins.

Table 16. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width,

package mechanical data

Symbol millimeters inches

Typ Min Max Typ Min Max

A1.750.069

A1 0.10 0.25 0.004 0.010

A2 1.25 0.049

b 0.28 0.48 0.011 0.019

c 0.17 0.23 0.007 0.009

ccc 0.10 0.004

D 4.90 4.80 5.00 0.193 0.189 0.197

E 6.00 5.80 6.20 0.236 0.228 0.244

E1 3.90 3.80 4.00 0.154 0.150 0.157

e1.27– –0.050– –

h 0.25 0.50 0.010 0.020

k0°8°0°8°

L 0.40 1.27 0.016 0.050

L1 1.04 0.041

SO-A

ccc

h x 45˚

0.25 mm

GAUGE PLANE

M24C16, M24C08, M24C04, M24C02, M24C01 Package mechanical

27/33

Figure 14. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead

2x3mm², outline

1. Drawing is not to scale.

2. The central pad (the area E2 by D2 in the above illustration) is pulled, internally, to VSS. It must not be

allowed to be connected to any other voltage or signal line on the PCB, for example during the soldering

process.

3. The circle in the top view of the package indicates the position of pin 1.

Table 17. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead

2x3mm², data

Symbol millimeters inches

Typ Min Max Typ Min Max

A 0.55 0.50 0.60 0.022 0.020 0.024

A1 0.02 0.00 0.05 0.001 0.000 0.002

b 0.25 0.20 0.30 0.010 0.008 0.012

D 2.00 1.90 2.10 0.079 0.075 0.083

D2 1.60 1.50 1.70 0.063 0.059 0.067

ddd 0.08 0.003

E 3.00 2.90 3.10 0.118 0.114 0.122

E2 0.20 0.10 0.30 0.008 0.004 0.012

e0.50– –0.020– –

L 0.45 0.40 0.50 0.018 0.016 0.020

L1 0.15 0.006

L3 0.30 0.012

UFDFPN-01

A1 ddd

Package mecha n ic al M24C16, M2 4C08, M24C04 , M2 4 C 0 2, M 24C 0 1

28/33

Figure 15. TSSOP8 – 8 lead Thin Shrink Small Out line, package outline

1. Drawing is not to scale.

2. The circle in the top view of the package indicates the position of pin 1.

Table 18. TSSOP8 – 8 lead Thin Shrink Small Outline, package mechanical data

Symbol millimeters inches

Typ. Min. Max. Typ. Min. Max.

A 1.200 0.0472

A1 0.050 0.150 0.0020 0.0059

A2 1.000 0.800 1.050 0.0394 0.0315 0.0413

b 0.190 0.300 0.0075 0.0118

c 0.090 0.200 0.0035 0.0079

CP 0.100 0.0039

D 3.000 2.900 3.100 0.1181 0.1142 0.1220

e 0.650 – – 0.0256 – –

E 6.400 6.200 6.600 0.2520 0.2441 0.2598

E1 4.400 4.300 4.500 0.1732 0.1693 0.1772

L 0.600 0.450 0.750 0.0236 0.0177 0.0295

L1 1.000 0.0394

α0° 8° 0° 8°

TSSOP8AM

EE1

A2A

M24C16, M24C08, M24C04, M24C02, M24C01 Package mechanical

29/33

Figure 16. TSSOP8 3x3mm² – 8 lead Thin Shrink Small Outlin e, 3x3mm² body size,

package outline

1. Drawing is not to scale.

2. The circle in the top view of the package indicates the position of pin 1.

Table 19. TSSOP8 3x3 mm² – 8 lead Thin Shrink Small Outline, 3x3mm² body size,

mechanical data

Symbol millimeters inches

Typ. Min. Max. Typ. Min. Max.

A 1.100 0.0433

A1 0.050 0.150 0.0020 0.0059

A2 0.850 0.750 0.950 0.0335 0.0295 0.0374

b 0.250 0.400 0.0098 0.0157

c 0.130 0.230 0.0051 0.0091

D 3.000 2.900 3.100 0.1181 0.1142 0.1220

E 4.900 4.650 5.150 0.1929 0.1831 0.2028

E1 3.000 2.900 3.100 0.1181 0.1142 0.1220

e 0.650 – – 0.0256 – –

CP 0.100 0.0039

L 0.550 0.400 0.700 0.0217 0.0157 0.0276

L1 0.950 0.0374

α0° 6° 0° 6°

TSSOP8BM

EE1

A2A

Part numbering M24C16, M24C08, M24C04, M24C02, M24C01

30/33

8 Part numbering

F o r a list of available options (speed, pac kag e, etc.) or fo r fu rther information on an y aspect

of this device, please contact your nearest ST Sales Office.

The category of second Level Interconnect is marked on the package and on the inner bo x

label, in compliance with JEDEC Standar d JESD97. The maximum ratings related to

soldering conditions are also marked on the inner box label.

Table 20. Ordering information scheme

Example: M24C16 – W DW 3 T P /W

Device Type

M24 = I2C serial access EEPROM

Device Function

16 = 16 Kbit (2048 x 8)

08 = 8 Kbit (1024 x 8)

04 = 4 Kbit (512 x 8)

02 = 2 Kbit (256 x 8)

01 = 1 Kbit (128 x 8)

Operating Voltage

W = VCC = 2.5 to 5.5V (400 kHz)

R = VCC = 1.8 to 5.5V (400 kHz)

Package

BN = PDIP8

MN = SO8 (150 mil width)

MB = UDFDFPN8 (MLP8)

DW = TSSOP8 (169 mil width)

DS = TSSOP8 (3x3mm² body size, MSOP8)(1)

1. Products sold in this package are Not Recommended for New Design.

Device Grade

6 = Industrial temperature range, –40 to 85 °C.

Device tested with standard test flow

3 = Device tested with High Reliability Certified Flow(2).

A u tomotive temperature range (–40 to 125 °C)

2. ST strongly recommends the use of the Automotive Grade devices for use in an automotive

environment. The High Reliability Certified Flow (HRCF) is described in the quality note

QNEE9801. Please ask your nearest ST sales office for a copy.

Option

T = Tape and Reel Packing

Plating Technology

blank = Standard SnPb plating

P or G = ECOPACK® (RoHS compliant)

Process(3)

3. Used only for Device Grade 3.

/W or /S = F6SP36%

M24C16, M24C08, M24C04, M24C02, M24C01 Revision history

31/33

9 Revision history

Table 21. Document revision history

Date Version Changes

10-Dec-1999 2.4 TSSOP8 Turned-Die package removed (p 2 and order information)

Lead temperature added for TSSOP8 in table 2

18-Apr-2000 2.5 Labelling change to Fig-2D , correction of values for ‘E’ and main caption for

Tab-13

05-May-2000 2.6 Extra labelling to Fig-2D

23-Nov-2000 3.0 SBGA package information removed to an annex document

-R range changed to being the -S range, and the new -R range added

19-Feb-2001 3.1

SBGA package information put back in this document

Lead Soldering Temperature in the Absolute Maximum Ratings table

amended

Write Cycle Polling Flow Chart usi ng ACK illustration updated

References to PSDIP changed to PDIP and Package Mechanical data

updated

Wording bro ught in to line with standard glossary

20-Apr-2001 3.2 Revision of DC and AC characteristics for the -S series

08-Oct-2001 3.3 Ball numbers added to the SBGA connections and package mechanical

illustrations

09-Nov-2001 3.4 Specification of Test Condition for Leakage Currents in the DC

Characteristics table improved

30-Jul-2002 3.5 Document reformatted using new template. SBGA5 package removed

TSSOP8 (3x3mm² body size) package (MSOP8) added. -L voltage range

added

04-Feb-2003 3.6 Document title spelt out more fully. “W”-marked devices with tw=5ms

added.

05-May-2003 3.7

-R voltage range upgraded to 400kHz working, and no longer preliminary

data.

5V voltage range at temperatur e range 3 (-xx3) no longer preliminary data.

-S voltage range removed. -Wxx3 voltage+temp ranged added as

preliminary data.

07-Oct-2003 4.0

Table of contents, and Pb-free options added. Minor wording changes in

Summary Description, Power-On Reset, Memory Addressing, Read

Operations. VIL(min) improved to

-0.45V. tW(max) value for -R voltage range corrected.

17-Mar-2004 5.0

MLP package added. Absolute Maximum Ratings for VIO(min) and

VCC(min) changed. Soldering temperature information clar ified for RoHS

compliant devices. Device grade information clarified. Process

identification letter “G” information added. 2.2-5.5V range is removed, and

4.5-5.5V range is now Not for New Design

Revision history M24C16, M24C08, M24C04, M24C02, M24C01

32/33

7-Oct-2005 6.0

Product List summary table added. AEC-Q100-002 compliance. Device

Grade inform ation clarified. Updated Device internal rese t section,

Figure 3, Figure 4, Table 14 and Table 20 Added Ecopack® information.

Updated tW=5ms for the M24Cxx-W.

17-Jan-2006 7.0

Pin numbers removed from silhouettes (see on pag e 1). Internal Device

Reset paragraph moved to below Section 2.4: Supply voltage (VCC).

Section 2.4: Sup ply voltage (VCC) added below Section 2: Signal

description. Test conditions for VOL updated in Table 8 and Table 9 SO8N

package specifications updated (see Table 16)

New definition of ICC1 over the whole VCC range (see Tables 8, 9 and 10).

19-Sep-2006 8

Document converted to new ST template.

SO8 and UFDFPN8 package specifications updated (see Section 7:

Package mechanical). Section 2.4: Supply voltage (VCC) clarified.

ILI value given with the device in Standby mode in Tables 8, 9 and 10.

Inf ormation given in Table 14: A C characteristics (M24Cxx-R) are no longer

preliminary data.

Table 21. Document revision history

Date Version Changes

M24C16, M24C08, M24C04, M24C02, M24C0 1

33/33

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

time, without notice.

All ST products are sold pursuant to ST’s terms and co nditions of sale.

Purchasers a re so lel y res ponsibl e fo r th e choic e, se lecti on an d use o f th e ST pr oduc ts and s ervi ces d escr ibed he rein , and ST as sumes no

liability whatsoever relating to the choice, selection or u se of the ST products and services descri bed herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this

document ref er s to an y t hi rd pa rt y p roduc t s or serv ic es it sh al l n ot be dee med a li ce nse gr an t by ST for t he use of su ch t hi rd party products

or services, or any intel lectual pro perty conta ined therei n or considere d as a warranty covering the use in any mann er whatsoev er of such

third party products or services or any intellec tual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED

WARRANTIES OF MERCHANTAB ILIT Y, FITNESS F OR A PARTI CULAR PURPOS E (AND THEIR EQUIVALE NTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT

RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING

APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,

DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE

GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void

any warrant y granted by ST for the S T product or se rvice descr ibed herein a nd shall no t create or e xtend in any manner whatsoe ver, any

liability of ST.

ST and the ST lo go are trademarks or regist ered trademar ks of ST in vari ous countri es.

Information in this document supers edes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroele ctr on ic s gr ou p of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America