V25
2
SPECIFICATIONS
All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted
INPUT SPECIFICATIONS: GENERAL SPECIFICATIONS:
Input Voltage Range ….………….......……....... 5V ….............................4.5-6V
Efficiency ….............................................................................. See Table
12V …..................... 9-18V
Isolation Voltage:
24V …..................... 18-36V
500 VDC min. ……………………….………………… Standard Models
48V …................... 36-72V
3K VDC min. …… (Non-Conductive Black Plastic Only) ….. Suffix “H” Models
Input Surge Voltage (100ms max.) …….…… 5V ….…….…...... 10Vdc max.
1.5K VDC min. ………..…..……………………… Suffix “HM” Models
12V …................. 25Vdc max.
Isolation Resistance ….....................................................… 10
9
ohm min.
24V …................. 50Vdc max.
Switching Frequency …........................................................ 100KHz min.
48V …............... 100Vdc max.
Operating Ambient Temperature Range …...................... -25℃ to +71℃
Input Filter ………………………………………………….…………….. Pi Type
Power de-rating Curve ………………..……………………….. see Figure1
OUTPUT SPECIFICATIONS:
Case Temperature (note4) … Plastic/Copper case … 95℃/100℃ max.
Voltage Accuracy …...................................................................... ±2.0% max.
Cooling ……………………………………………….. Natural Convection
Voltage Balance (Dual) …..............................................................
±1.0% max.
Storage Temperature Range ………….……....……..... -40℃ to +100℃
Temperature Coefficient ……………………..……………………… ±0.05%/℃
Humidity .................................................. 95% RH max. Non condensing
Ripple & Noise, 20MHz BW .……………… 3.3V/5V ……. 100mV pk-pk, max.
MTBF ………. MIL-STD-217F ..……..……………………… 2000Khrs typ.
12V/15V …..…… 1% pk-pk max.
Dimensions …… DIP …..… 1.25×0.80x0.40 inches(31.8x20.3×10.2 mm)
Short Circuit Protection ……………………………………………… Continuous
SMD …… 1.25×0.80x0.45 inches(31.8x20.3×11.4 mm)
Line Regulation ………… Single/Dual (note1) …………………. ±0.5% max.
Case Material:
Load Regulation ……..… Single (note2) …………....…………. ±0.5% max.
Standard Models …………………….… Non-Conductive Black Plastic
Dual (note3) ….….….……………… ±1.0% max.
Suffix “M” Models .. Black Coated Copper with Non-conductive Base
NOTE:
Weight ………………………………………………….……………… 12.5g
1. Measured from high line to low line.
2. Measured from full load to 10% load.
3. Measured from full load to 1/4 load.
4. Maximum case temperature under any operating condition should
not be exceed 95℃(Plastic Case), 100℃(Copper Case).
Case A Dimensions:
BOTTOM
VIEW
SEE NOTE
PIN CONNECTION
500 VDC 1.5K & 3K VDC
Pin Single Output Dual Output
1,24
2,23
3,22
10,15
11,14
12,13
+V Input
NC
NC
-V Output
+V Output
-V Input
+V Input
-V Output
-V Input
Common
Common
+V Output
* NP-NO PIN
* NC-NO CONNECTION WITH PIN
NOTE:Pin Size is 0.02 ±0.002 Inch (0.5±0.05 mm)DIA
All Dimensions In Inches (mm)
Tolerances Inches: X.XX= ±0.02 , X.XXX= ±0.010
Millimeters: X.X= ±0.5 , X.XX=±0.25
9
4
20,21
CASE AS
TOP
VIEW
DIP SMD
NP NC
NP NC
NP NC
DIP SMD
Pin Single Output Dual Output
DIP SMD DIP SMD
NP NC
NP NC
NP NC
NC
NC -V Output
Common
-V Input -V Input
+V Output
+V Output
Common
-V Output
+V Input +V Input
1,24
2,3
10,15
11
12,13
14
9
22,23
16
4,5
20,21
NP NC NP NC
NP NC NP NC
NC NC
NP NC NP NC
NP NC NP NC
16 NP NC NP NC
5NP NC NP NC
Figure1.Typical Derating curve for Natural Convection
95
71
-25
100
0%
20%
40%
60%
80%
100%
120%
-25 0 25 50 75 100
Ambient Temperature(
o
C)
LOAD(%)
Plastic Case
Copper Case