LPD5010-224MEB - Coilcraft - Product.Network

Taiwan

China

Singapore

+1-847-639-6400 sales@coilcraft.com

+44-1236-730595 sales@coilcraft-europe.com

+886-2-2264 3646 sales@coilcraft.com.tw

+86-21-6218 8074 sales@coilcraft.com.cn

+ 65-6484 8412 sales@coilcraft.com.sg

This product may not be used in medical or high

risk applications without prior Coilcraft approval.

Specification subject to change without notice.

Please check web site for latest information.

Document 820-1

Document 820-1 Revised 07/13/16

Dimensions are in inches

0.060

1,52

0.035 ±0.004

0,9 ±0,1

Dash

number Internal

code

Dot indicates pin 1

0.189 ±0.003

4,80 ±0,076

0.189 ±0.003

4,80 ±0,076

XXX X

Recommended

Land Pattern

0.197

5,00

0.134

3,40

0.060

1,50

0.138

3,50

0.197

5,00

45°

typ

0.090

2,30

0.134

3,40

0.090

2,30

0.030

0,75

Dimensions are of the case not including

the termination. For maximum overall

dimensions including the termination, add

0.005 in/0.13 mm.

For optional tin-lead and tin-silver-copper

terminations, dimensions are for the

mounted part. Dimensions before mounting

can be an additional 0.005 in/0.13 mm.

Shielded Coupled Inductors LPD5010

The LPD5010 coupled miniature shielded inductors are

mere 1 mm high and 5 mm square. They are ideal for use

in a variety of circuits including ﬂyback, multi-output buck,

SEPIC and Zeta.

These inductors provide high inductance, high efﬁciency

and excellent current handling in a rugged, low cost part.

They can also be used as two single inductors connected

in series or parallel or as a common mode choke.

L1 L2

–

Typical Flyback Converter

VOUT

––

–

Typical Buck Converter with auxiliary output

VOUT

VOUTAU

Typical Zeta schematic

VOUT

IN L1

QC1

––

Typical SEPIC schematic

VOUT

––

Taiwan

China

Singapore

+1-847-639-6400 sales@coilcraft.com

+44-1236-730595 sales@coilcraft-europe.com

+886-2-2264 3646 sales@coilcraft.com.tw

+86-21-6218 8074 sales@coilcraft.com.cn

+ 65-6484 8412 sales@coilcraft.com.sg

This product may not be used in medical or high

risk applications without prior Coilcraft approval.

Specification subject to change without notice.

Please check web site for latest information.

Coupled Inductors for SEPIC Applications – LPD5010 Series

Document 820-2

Document 820-2 Revised 07/13/16

Coupling Leakage Isat (A)6 Irms (A)

Inductance2 DCR max3 SRF typ4 coefﬁcient

L typ5 10% 20% 30% both one

Part number1 ±20% (µH) (Ohms) (MHz) typ (µH) drop drop drop windings7

winding8

LPD5010-681MR_ 0.68 0.07 191 0.95 0.07 2.6 2.7 2.8 1.95 2.76

LPD5010-102MR_ 1.0 0.10 150 0.95 0.09 2.1 2.1 2.2 1.50 2.12

LPD5010-152MR_ 1.5 0.15 134 0.97 0.09 1.7 1.8 1.8 1.20 1.70

LPD5010-222MR_ 2.2 0.20 108 0.97 0.11 1.5 1.6 1.6 1.10 1.56

LPD5010-332MR_ 3.3 0.27 83 0.98 0.13 1.2 1.3 1.3 0.95 1.34

LPD5010-472MR_ 4.7 0.40 68 0.98 0.15 0.98 1.0 1.1 0.75 1.06

LPD5010-562MR_ 5.6 0.45 60 0.99 0.16 0.90 0.93 0.94 0.70 0.99

LPD5010-682MR_ 6.8 0.53 55 0.99 0.19 0.83 0.86 0.87 0.60 0.85

LPD5010-822MR_ 8.2 0.70 50 0.99 0.22 0.74 0.77 0.78 0.50 0.71

LPD5010-103MR_ 10 0.78 46 0.99 0.27 0.67 0.69 0.70 0.50 0.71

LPD5010-153MR_ 15 1.19 33 0.99 0.34 0.53 0.55 0.56 0.42 0.59

LPD5010-223MR_ 22 1.58 26 0.99 0.40 0.45 0.47 0.48 0.35 0.49

LPD5010-333MR_ 33 2.50 23 0.99 0.48 0.37 0.38 0.39 0.30 0.42

LPD5010-473MR_ 47 3.48 17.0 0.99 0.63 0.31 0.32 0.33 0.25 0.35

LPD5010-683MR_ 68 5.10 14.9 0.99 0.90 0.25 0.26 0.27 0.19 0.26

LPD5010-104MR_ 100 8.0 11.2 0.99 1.39 0.21 0.22 0.22 0.15 0.21

LPD5010-154MR_ 150 11.7 9.90 0.99 2.10 0.17 0.17 0.18 0.12 0.16

LPD5010-224MR_ 220 15.2 8.05 0.99 3.02 0.14 0.15 0.15 0.11 0.15

1. Please specify termination and packaging codes:

LPD5010-224MRC

Termination: R = RoHS compliant matte tin over nickel over silver.

Special order:

Q = RoHS tin-silver-copper (95.5/4/0.5) or

P = non-RoHS tin-lead (63/37).

Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic

tape (1000 parts per full reel).

B = Less than full reel. In tape, but not machine ready.

To have a leader and trailer added ($25 charge), use

code letter C instead.

D = 13″ machine-ready reel. EIA-481 embossed plastic

tape. Factory order only, not stocked (3500 parts per

full reel).

2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,

0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads

are connected in parallel, inductance is the same value. When leads are

connected in series, inductance is four times the value.

3. DCR is for each winding. When leads are connected in parallel, DCR

is half the value. When leads are connected in series, DCR is twice the

value.

4. SRF measured using an Agilent/HP 4191A or equivalent. When leads

are connected in parallel, SRF is the same value.

5. Leakage Inductance is for L1 and is measured with L2 shorted.

6. DC current at 25°C that causes the speciﬁed inductance drop from its

value without current. It is the sum of the current ﬂowing in both windings.

7. Equal current when applied to each winding simultaneously that causes

a 40°C temperature rise from 25°C ambient. This information is for refer-

ence only and does not represent absolute maximum ratings.

8. Maximum current when applied to one winding that causes a 40°C tem-

perature rise from 25°C ambient. This information is for reference only

and does not represent absolute maximum ratings.

9. Electrical speciﬁcations at 25°C.

Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”

Refer to Doc 362 “Soldering Surface Mount Components” before soldering.

Coupled Inductor Core and Winding Loss Calculator

This web-based utility allows you to enter frequency, peak-to-peak (ripple)

current, and Irms current to predict temperature rise and overall losses,

including core loss. Go to online calculator.

Core material Ferrite

Core and winding loss Go to online calculator

Weight 60 – 70 mg

Environmental RoHS compliant, halogen free

Terminations RoHS compliant matte tin over nickel over silver.

Other terminations available at additional cost.

Ambient temperature –40°C to +85°C with (40°C rise) Irms current.

Maximum part temperature +125°C (ambient + temp rise).

Storage temperature Component: –40°C to +125°C.

Tape and reel packaging: –40°C to +80°C

Winding to winding isolation 100 Vrms, one minute

Resistance to soldering heat Max three 40 second reﬂows at

+260°C, parts cooled to room temperature between cycles

Moisture Sensitivity Level (MSL) 1 (unlimited ﬂoor life at <30°C /

85% relative humidity)

Mean Time Between Failures (MTBF) 26,315,789 hours

Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,

0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth

Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm

PCB washing Tested with pure water or alcohol only. For other

solvents, see Doc787_PCB_Washing.pdf.

Taiwan

China

Singapore

+1-847-639-6400 sales@coilcraft.com

+44-1236-730595 sales@coilcraft-europe.com

+886-2-2264 3646 sales@coilcraft.com.tw

+86-21-6218 8074 sales@coilcraft.com.cn

+ 65-6484 8412 sales@coilcraft.com.sg

This product may not be used in medical or high

risk applications without prior Coilcraft approval.

Specification subject to change without notice.

Please check web site for latest information.

Coupled Inductors for SEPIC Applications – LPD5010 Series

Document 820-3

Document 820-3 Revised 07/13/16

Typical L vs Current Typical L vs Frequency

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Coilcraft:

LPD5010-152MEC LPD5010-332MEB LPD5010-683MEB LPD5010-104MEC LPD5010-682MEB LPD5010-

104MEB LPD5010-222MEC LPD5010-333MEC LPD5010-223MEB LPD5010-562MEC LPD5010-472MEC

LPD5010-224MEB LPD5010-154MEC LPD5010-682MEC LPD5010-472MEB LPD5010-822MEB LPD5010-473MEC

LPD5010-103MEC LPD5010-153MEC LPD5010-152MEB LPD5010-222MEB LPD5010-153MEB LPD5010-

102MEB LPD5010-224MEC LPD5010-103MEB LPD5010-683MEC LPD5010-562MEB LPD5010-333MEB

LPD5010-681MEC LPD5010-223MEC LPD5010-822MEC LPD5010-473MEB LPD5010-681MEB LPD5010-102MEC

LPD5010-332MEC LPD5010-154MEB