Catalog 1308242 Issued 3-03 (PDF Rev. 9-05) P&B W33 series One- and Two-Pole, Switchable Thermal Circuit Breaker / Power Switch With Optional Indicator Lamp Features Electrical Data @ 25C * Combines on/off switch and circuit protection in a single unit. * 2 to 20 amp ratings (<2A types available as special order). * One or two pole sensing. * Lighted or non-lighted rocker actuator in various colors. * Convenient, snap-in mounting. * Optional auxiliary switch available. * Trip-free operation. Calibration: Breaker will continuously carry 100% of rated load. It may trip between 101% and 135%, but must trip at 135% within one hour at +25C. Dielectric Strength: Over 2,000 volts RMS. Maximum Operating Voltages: 50VDC; 250VAC to 400 Hz. Interrupt Capacity: 1,000 amps at 50VDC; 250VAC, 60 Hz. and 125/250VAC, 400 Hz. 1,500 amps at 125/250VAC, 60 Hz. Resettable Overload Capacity: Ten times rated current. Agency Approvals Mechanical/Environmental Data W33 series is UL 1077 Recognized as Supplementary Protectors, File E69543, and CSA Accepted as Supplementary Protectors (Appliance Component Protectors), File LR15734. Termination: Poles 1&2: .250" (6.35mm) quick connect/solder terminals. Opt. Aux. Sw.: .110"(2.79mm) quick connect terminals. Mounting: Snaps into panel from front. Actuator: Rocker or lighted rocker. Shock: 30g tested to IEC 68-2-27, test Ea. Vibration: 8g tested to IEC 68-2-6, test Fc. Switch Endurance Cycling: 50,000 operations at rated load. 1,000 operations at 200% rated load. Users should thoroughly review the technical data before selecting a product part number. It is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. Ambient Compensation Chart Time vs. Current Trip Curve @ +25C 1000 800 700 600 1.30 Correction Factor 900 Load Current As A Percent Of Breaker Rating 1.40 All Models Overload Trip Times No Trip 100% Trip in 1 hour 135% 3.0 - 33 Sec. 200% 0.6 - 10 Sec. 400% 0.34 - 5 Sec. 600% 0.25 - 2.2 Sec. 800% 0.20 - 0.6 Sec. 1000% 500 0.90 0.80 -20 -10 0 10 20 30 40 50 60 Ambient Temperature In Degrees Centigrade (C) 200 100 1 10 100 1000 Time In Seconds Dimensions are shown for 1.00 0.60 300 114 reference purposes only. 1.10 0.70 400 0 .1 1.20 Dimensions are in inches over (millimeters) unless otherwise specified. Specifications and availability subject to change. To use this chart: Read up from the ambient temperature to the curve, and across to find a correction factor. Multiply the breaker rating by the correction factor to determine the compensated rating. Calculate the overloads in terms of the compensated rating to use the published trip curve. www.tycoelectronics.com Technical support: Refer to inside back cover. Catalog 1308242 Issued 3-03 (PDF Rev. 9-05) P&B Ordering Information Typical Part No. B W 33 -S 1 N 1 Q -20 1. Designator: W = Circuit breaker 2. Series Number: 33 = Two pole, rocker actuated 3. Circuit Function: S = Pole 1 - Switch only; Pole 2 - Series trip overload sensing. T = Poles 1 & 2 - Series trip overload sensing. SS = Same as S with auxiliary switch on pole 1. TS = Same as T with auxiliary switch on pole 1. D = 2 Pole switching. 4. Rocker Color: 1 = Black. 2 = White. 3 = Red. 4 = Amber. 5 = Smoke. 5. Light (available only with White, Red, Amber and Smoke rocker colors): A = 24VDC (Incandescent). B = 120VAC (Neon with resistor). C = 240VAC (Neon with resistor). 6. Marking: 1 = International I/O. N = No light. 2 = Contrasting I/O stamp (white toggle with black stamp). 7. Termination: Q = .250" x .032" (6.35 x .813mm) quick connect / solder terminals. 8. Amp Rating: 2 5 7 10 12 15 16 20 Consult factory for availability of ratings <2A Stock Items - Authorized distributors are more likely to stock the following items. W33-T4B1Q-5 W33-T4B1Q-10 W33-T4B1Q-15 W33-S4B1Q-10 W33-S4B1Q-15 W33-T2N1Q-20 W33-S1N1Q-5 W33-S1N1Q-15 W33-S1N1Q-20 Schematic Outline Dimensions POLE 2 ROCKER .980 (24.89) 1.724 (43.79) .850 (21.59) I 1.890 (48.01) 0 POLE 1 LINE SIDE 1.690 (42.93) 1.120 (28.45) PANEL CLAMPING ARRANGEMENT .412 (10.46) .250 (6.35) LOAD SIDE NEON - AC INCANDESCENT - DC FITS .875 x 1.750 (22.22 x 44.45) PANEL OPENING FROM .032" - .250"(.813mm - 6.35mm) THICK Dimensions are shown for reference purposes only. Dimensions are in inches over (millimeters) unless otherwise specified. Specifications and availability subject to change. www.tycoelectronics.com Technical support: Refer to inside back cover. 115