N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module Kenndaten TT92N TT92N TD92N DT92N TT92N..K..-K TD92N..K..-A NT92N Elektrische Eigenschaften Elektrische Eigenschaften / Electrical properties Hochstzulassige Werte / Maximum rated values Periodische Vorwarts- und Ruckwarts-Spitzensperrspannung Tvj = -40C... Tvj max repetitive peak forward off-state and reverse voltages VDRM,VRRM 1200 1400 V 1600 V Vorwarts-Stospitzensperrspannung non-repetitive peak forward off-state voltage Tvj = -40C... Tvj max VDSM 1200 1400 V 1600 V Ruckwarts-Stospitzensperrspannung non-repetitive peak reverse voltage Tvj = +25C... Tvj max VRSM 1300 1500 V 1700 V Durchlastrom-Grenzeffektivwert maximum RMS on-state current ITRMSM 160 A Dauergrenzstrom average on-state current TC = 85C TC = 76C ITAVM 92 A 104 A Stostrom-Grenzwert surge current Tvj = 25 C, tP = 10 ms Tvj = Tvj max, tP = 10 ms ITSM 2050 A 1800 A Grenzlastintegral It-value Tvj = 25 C, tP = 10 ms Tvj = Tvj max, tP = 10 ms It Kritische Stromsteilheit critical rate of rise of on-state current DIN IEC 747-6 f = 50 Hz, iGM = 0,6 A, diG/dt = 0,6 A/s (diT/dt)cr Kritische Spannungssteilheit critical rate of rise of off-state voltage Tvj = Tvj max, vD = 0,67 VDRM 6.Kennbuchstabe / 6th letter F (dvD/dt)cr Charakteristische Werte / Characteristic values Durchlaspannung on-state voltage Tvj = Tvj max , iT = 300 A vT Schleusenspannung threshold voltage Tvj = Tvj max V(TO) 0,85 V Ersatzwiderstand slope resistance Tvj = Tvj max rT 2,15 m Zundstrom gate trigger current Tvj = 25C, vD = 6 V IGT max. 120 mA Zundspannung gate trigger voltage Tvj = 25C, vD = 6 V VGT max. 1,4 V Nicht zundender Steuerstrom gate non-trigger current Tvj = Tvj max , vD = 6 V Tvj = Tvj max , vD = 0,5 VDRM IGD max. max. 5,0 mA 2,5 mA Nicht zundende Steuerspannung gate non-trigger voltage Tvj = Tvj max , vD = 0,5 VDRM VGD max. 0,2 V Haltestrom holding current Tvj = 25C, vD = 6 V, RA = 5 IH max. 200 mA Einraststrom latching current Tvj = 25C, vD = 6 V, RGK 10 iGM = 0,6 A, diG/dt = 0,6 A/s, tg = 20 s IL max. 620 mA Vorwarts- und Ruckwarts-Sperrstrom forward off-state and reverse current Tvj = Tvj max vD = VDRM, vR = VRRM iD, iR max. 25 mA Zundverzug gate controlled delay time DIN IEC 747-6 Tvj = 25 C, iGM = 0,6 A, diG/dt = 0,6 A/s tgd max. 3 s prepared by: C.Drilling date of publication: revision: approved by: J. Novotny BIP AC/ 27.05.2002, C. Drilling A8/02 21000 As 16200 As 150 A/s 1000 V/s max. 1,62 V 09.07.02 3 Seite/page 1/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N Elektrische Eigenschaften / Electrical properties Charakteristische Werte / Characteristic values Freiwerdezeit circuit commutated turn-off time Isolations-Prufspannung insulation test voltage Tvj = Tvj max, iTM = ITAVM vRM = 100 V, vDM = 0,67 VDRM dvD/dt = 20 V/s, -diT/dt = 10 A/s 5.Kennbuchstabe / 5th letter O tq RMS, f = 50 Hz, t = 1 min RMS, f = 50 Hz, t = 1 sec VISOL typ. Thermische Eigenschaften Thermische Eigenschaften / Thermal properties Innerer Warmewiderstand thermal resistance, junction to case Ubergangs-Warmewiderstand thermal resistance, case to heatsink 2,5 kV 3,0 kV pro Modul / per Module, = 180 sin RthJC pro Zweig / per arm, = 180 sin pro Modul / per Module, DC pro Zweig / per arm, DC max. max. max. max. pro Modul / per Module pro Zweig / per arm max. max. RthCH 150 s 0,185 0,370 0,175 0,350 C/W C/W C/W C/W 0,05 C/W 0,10 C/W 130 C Hochstzulassige Sperrschichttemperatur maximum junction temperature Tvj max Betriebstemperatur operating temperature Tc op -40...+130 C Lagertemperatur storage temperature Tstg -40...+130 C Mechanische Eigenschaften Mechanische Eigenschaften / Mechanical properties Gehause, siehe Anlage case, see annex Seite 3 page 3 Si-Element mit Druckkontakt Si-pellet with pressure contact Innere Isolation internal insulation AlN Anzugsdrehmoment fur mechanische Anschlusse mounting torque Toleranz / Tolerance 15% M1 4 Nm Anzugsdrehmoment fur elektrische Anschlusse terminal connection torque Toleranz / Tolerance 10% M2 4 Nm Steueranschlusse control terminals DIN 46 244 Gewicht weight G Kriechstrecke creepage distance Schwingfestigkeit vibration resistance A 2,8 x 0,8 typ. 160 g 12,5 mm f = 50 Hz file-No. 50 m/s E 83336 Mit diesem Datenblatt werden Halbleiterbauelemente spezifiziert, jedoch keine Eigenschaften zugesichert. Es gilt in Verbindung mit den zugehorigen technischen Erlauterungen. This data sheet specifies semiconductor devices, but promises no characteristics. It is valid in combination with the belonging technical notes. BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 2/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N Mabild Mabild Mabild 1 2 5 4 3 1 2 7 6 TT 1 2 3 5 4 1 2 3 7 6 DT TD 3 4 5 7 6 1 2 3 TT-K BIP AC/ 27.05.2002, C. Drilling TD-A A8/02 2 3 7 6 5 4 NT Seite/page 3/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module R,T - Werte Di R,T-Werte TT92N Analytische Elemente des transienten Warmewiderstandes Z thJC fur DC Analytical elements of transient thermal impedance Z thJC for DC Pos. n 1 2 3 4 5 6 Rthn [C/W] 0,005 0,0195 0,0518 0,128 0,146 n [s] 0,00004 0,00223 0,022 0,235 1,24 7 n max Z thJC = Analytische Funktion / Analytical function: S n=1 R thn 1 - e -t tn Luftselbstkuhlung / Natural cooling 3 Module pro Kuhlkorper / 3 modules per heatsink Kuhler / Heatsink type: KM14 (50W) Analytische Elemente des transienten Warmewiderstandes Z thCA Analytical elements of transient thermal impedance Z thCA Pos. n 1 2 3 4 Rthn [C/W] 0,007 0,141 0,119 2,133 n [s] 0,701 4,72 42,5 910 5 6 7 6 7 Verstarkte Kuhlung / Forced cooling 3 Module pro Kuhlkorper / 3 modules per heatsink Kuhler / Heatsink type: KM14 (Papst 4650N) Analytische Elemente des transienten Warmewiderstandes Z thCA Analytical elements of transient thermal impedance Z thCA Pos. n 1 2 3 4 Rthn [C/W] 0,007 0,141 0,119 0,583 n [s] 0,701 4,72 42,5 249 5 nmax Analytische Funktion / Analytical function: BIP AC/ 27.05.2002, C. Drilling A8/02 Z thCA = S n=1 Rthn 1 - e -t tn Seite/page 4/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 0,500 = 30 Diagramme Trans. Warmewiderstand bei Sinus 0,400 Z(th)JC [C/W] 0 60 90 120 180 180 0 0,300 0,200 0,100 0,000 0,01 0,1 1 t [s] 10 100 Transienter innerer Warmewiderstand je Zweig / Transient thermal impedance per arm ZthJC = f(t) Sinusformiger Strom / Sinusoidal current Parameter: Stromfluwinkel / Current conduction angle Trans. Warmewiderstand bei Rechteck 0,600 = 30 0,500 60 0 Z(th)JC [C/W] 0,400 0 90 180 120 180 DC 0,300 0,200 0,100 0,000 0,001 0,01 0,1 t [s] 1 10 100 Transienter innerer Warmewiderstand je Zweig / Transient thermal impedance per arm ZthJC = f(t) Rechteckformiger Strom / Rectangular current Parameter: Stromfluwinkel / Current conduction angle BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 5/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 160 Diagramme 180 Durchgangsverluste bei Sinus 120 140 0 120 90 180 0 PTAV [W] 60 100 Q = 30 80 60 40 20 0 0 20 40 60 ITAV [A] 80 100 120 Durchlassverlustleistung je Zweig / On-state power loss per arm PTAV = f(ITAV) Sinusformiger Strom / Sinusoidal current Strombelastung je Zweig / Current load per arm Parameter: Stromfluwinkel / Current conduction angle Durchgangsverluste bei Rechteck 200 DC 0 150 180 180 0 120 PTAV [W] 90 60 Q = 30 100 50 0 0 20 40 80 ITAV [A] 100 60 120 140 160 180 Durchlassverlustleistung je Zweig / On-state power loss per arm PTAV = f(ITAV) Rechteckformiger Strom / Rectangular current Strombelastung je Zweig / Current load per arm Parameter: Stromfluwinkel / Current conduction angle BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 6/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N Gehausetemperatur bei Sinus 140 120 0 180 TC [C] 0 100 80 60 60 Q = 30 40 90 180 120 20 0 20 40 60 ITAVM [A] 80 100 120 Hochstzulassige Gehausetemperatur / Maximum allowable case temperature TC = f(ITAVM) Sinusformiger Strom / Sinusoidal current Strombelastung je Zweig / Current load per arm Parameter: Stromfluwinkel / Current conduction angle Gehausetemperatur bei Rechteck 140 120 0 180 0 TC [C] 100 80 60 40 60 Q = 30 90 120 DC 180 20 0 20 40 60 80 100 120 ITAVM [A] 140 160 180 Hochstzulassige Gehausetemperatur / Maximum allowable case temperature TC = f(ITAVM) Rechteckformiger Strom / Rectangular current Strombelastung je Zweig / Current load per arm Parameter: Stromfluwinkel / Current conduction angle BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 7/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module 600 0,10 B2 RthCA [C/W] 0,08 + ~ 0,15 400 ID Maximaler Strom bei B2 und B6 0,12 500 TT92N R-Last R-load L-Last L-load - 0,20 0,25 300 0,30 0,40 200 0,50 0,60 0,80 1,00 1,50 2,00 100 0 0 20 40 T A [C] 60 80 100 120 0 50 100 I D [A] 150 200 Hochstzulassiger Ausgangsstrom / Maximum rated output current ID B2- Zweipuls-Bruckenschaltung / Two-pulse bridge circuit Gesamtverlustleistung der Schaltung / Total power dissipation at circuit Ptot Parameter: Warmewiderstand zwischen den Gehausen und Umgebung / Thermal resistance cases to ambient RthCA 700 0,08 0,10 600 0,15 400 0,20 ID + 0,12 500 B6 R thCA [C/W] 3~ - 0,25 300 0,30 0,40 0,50 0,60 200 0,80 1,00 1,50 100 0 0 20 40 T A [C] 60 80 100 120 0 50 100 ID [A] 150 200 Hochstzulassiger Ausgangsstrom / Maximum rated output current ID B6- Sechspuls-Bruckenschaltung / Six-pulse bridge circuit Gesamtverlustleistung der Schaltung / Total power dissipation at circuit Ptot Parameter: Warmewiderstand zwischen den Gehausen und Umgebung / Thermal resistance cases to ambient RthCA BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 8/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 300 0,20 0,15 Maximaler Strom bei W1C und W3C IRMS 0,25 250 W 1C ~ R thCA [C/W] 0,12 0,30 200 0,40 ~ 0,50 150 0,60 0,80 100 1,00 1,20 1,50 2,00 3,00 50 0 0 20 40 T [C] 60 A 80 100 120 0 50 100 I RMS [A] 150 200 Hochstzulassiger Effektivstrom / Maximum rated RMS current IRMS W1C - Einphasen-Wechselwegschaltung / Single-phase inverse parallel circuit Gesamtverlustleistung der Schaltung / Total power dissipation at circuit Ptot Parameter: Warmewiderstand zwischen den Gehause und Umgebung / Thermal resistance case to ambient RthCA 700 0,10 0,08 R thCA [C/W] ~ W 3C ~ ~ IRMS 0,12 600 0,15 500 ~ ~ ~ 0,20 400 0,25 300 0,30 200 0,40 0,50 0,60 100 0,80 1,00 1,50 0 0 20 40 60 80 100 T A [C] 120 0 50 100 I RMS [A] 150 200 Hochstzulassiger Effektivstrom / Maximum rated RMS current IRMS W3C - Dreiphasen-Wechselwegschaltung / Three-phase inverse parallel circuit Gesamtverlustleistung der Schaltung / Total power dissipation at circuit Ptot Parameter: Warmewiderstand zwischen den Gehausen und Umgebung / Thermal resistance cases to ambient RthCA BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 9/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 100 Steuercharakteristik 10 d a b c 1 0,1 1 10 iG [mA] 100 1000 10000 100000 Steuercharakteristik vG = f (iG) mit Zundbereichen fur VD = 6 V Gate characteristic vG = f (iG) with triggering area for VD = 6 V Hochstzulassige Spitzensteuerverlustleistung / Maximum rated peak gate power dissipation PGM = f (tg) : a - 40 W/10ms b - 80 W/1ms 1000 c - 100 W/0,5ms d - 150W/0,1ms Zundverzug tgd [s] 100 10 a b 1 0,1 10 iGM [mA] 100 1000 10000 Zundverzug / Gate controlled delay time tgd = f(iG) Tvj = 25C, diG/dt = iGM/1s a - maximaler Verlauf / Limiting characteristic b - typischer Verlauf / Typical characteristic BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 10/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 1000 iTM = 500A Sperrverzogerungsladung 200A 100A 50A 20A 100 1 10 -di/dt [A/s] 100 Sperrverzogerungsladung / Recovered charge Qr = f(-di/dt) Tvj = Tvjmax, vR 0,5 VRRM, vRM = 0,8 VRRM Parameter: Durchlastrom / On-state current iTM Grenzstrom IT(OV)M [A] 1.600 a 1.400 TA = 35 C 1.200 1.000 b 800 TA = 45 C 600 400 200 0 0,01 0,1 1 t [s] Grenzstrom / Maximum overload on-state current IT(OV)M = f(t), vRM = 0,8 VRRM a: Leerlauf / No-load conditions b: nach Belastung mit ITAVM / after load with ITAVM TA = 35C, Luftselbstkuhlung / Forced air cooling TA = 45C, naturliche Luftkuhlung / Natural air cooling BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 11/12 N Datenblatt / Data sheet Netz-Thyristor-Modul Phase Control Thyristor Module TT92N 1.000 I TAV (vor) = Uberstrom 0A 5A 10 A 15 A 20 A 25 A IT(OV) [A] 800 600 400 200 0 0,01 0,1 1 t [s] 10 100 1000 10000 Uberstrom je Zweig / Overload on-state current IT(OV) B6- Sechspuls-Bruckenschaltung, 120 Rechteck / Six-pulse bridge circuit, 120 rectangular Kuhlkorper / Heatsink type KM14 (50W) Luftselbstkuhlung bei / Natural cooling at TA = 45C Parameter: Vorlaststrom je Zweig / Pre-load current per arm ITAV(vor) 1.000 I TAV (vor) = 0A 20 A 30 A 40 A 50 A 60 A IT(OV) [A] 800 600 400 200 0 0,01 0,1 1 t [s] 10 100 1000 10000 Uberstrom je Zweig / Overload on-state current IT(OV) B6- Sechspuls-Bruckenschaltung, 120 Rechteck / Six-pulse bridge circuit, 120 rectangular Kuhlkorper / Heatsink type KM14 (Papst 4650N) verstarkte Kuhlung bei / Forced cooling at TA = 35C Parameter: Vorlaststrom je Zweig / Pre-load current per arm ITAV(vor) BIP AC/ 27.05.2002, C. Drilling A8/02 Seite/page 12/12 Nutzungsbedingungen Die in diesem Produktdatenblatt enthaltenen Daten sind ausschlielich fur technisch geschultes Fachpersonal bestimmt. Die Beurteilung der Geeignetheit dieses Produktes fur die von Ihnen anvisierte Anwendung sowie die Beurteilung der Vollstandigkeit der bereitgestellten Produktdaten fur diese Anwendung obliegt Ihnen bzw. Ihren technischen Abteilungen. In diesem Produktdatenblatt werden diejenigen Merkmale beschrieben, fur die wir eine liefervertragliche Gewahrleistung ubernehmen. Eine solche Gewahrleistung richtet sich ausschlielich nach Magabe der im jeweiligen Liefervertrag enthaltenen Bestimmungen. Garantien jeglicher Art werden fur das Produkt und dessen Eigenschaften keinesfalls ubernommen. Sollten Sie von uns Produktinformationen benotigen, die uber den Inhalt dieses Produktdatenblatts hinausgehen und insbesondere eine spezifische Verwendung und den Einsatz dieses Produktes betreffen, setzen Sie sich bitte mit dem fur Sie zustandigen Vertriebsburo in Verbindung (siehe www.eupec.com, Vertrieb&Kontakt). Fur Interessenten halten wir Application Notes bereit. Aufgrund der technischen Anforderungen konnte unser Produkt gesundheitsgefahrdende Substanzen enthalten. Bei Ruckfragen zu den in diesem Produkt jeweils enthaltenen Substanzen setzen Sie sich bitte ebenfalls mit dem fur Sie zustandigen Vertriebsburo in Verbindung. Sollten Sie beabsichtigen, das Produkt in Anwendungen der Luftfahrt, in gesundheits- oder lebensgefahrdenden oder lebenserhaltenden Anwendungsbereichen einzusetzen, bitten wir um Mitteilung. Wir weisen darauf hin, dass wir fur diese Falle - die gemeinsame Durchfuhrung eines Risiko- und Qualitatsassessments; - den Abschluss von speziellen Qualitatssicherungsvereinbarungen; - die gemeinsame Einfuhrung von Manahmen zu einer laufenden Produktbeobachtung dringend empfehlen und gegebenenfalls die Belieferung von der Umsetzung solcher Manahmen abhangig machen. Soweit erforderlich, bitten wir Sie, entsprechende Hinweise an Ihre Kunden zu geben. Inhaltliche Anderungen dieses Produktdatenblatts bleiben vorbehalten. Terms & Conditions of usage The data contained in this product data sheet is exclusively intended for technically trained staff. You and your technical departments will have to evaluate the suitability of the product for the intended application and the completeness of the product data with respect to such application. This product data sheet is describing the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its characteristics. Should you require product information in excess of the data given in this product data sheet or which concerns the specific application of our product, please contact the sales office, which is responsible for you (see www.eupec.com, sales&contact). For those that are specifically interested we may provide application notes. Due to technical requirements our product may contain dangerous substances. For information on the types in question please contact the sales office, which is responsible for you. Should you intend to use the Product in aviation applications, in health or live endangering or life support applications, please notify. Please note, that for any such applications we urgently recommend - to perform joint Risk and Quality Assessments; - the conclusion of Quality Agreements; - to establish joint measures of an ongoing product survey, and that we may make delivery depended on the realization of any such measures. If and to the extent necessary, please forward equivalent notices to your customers. Changes of this product data sheet are reserved.