Sensing distance Supply voltage Output 12 to 24 VDC 80 mA 100 mA 3 to 10 cm, 5 to 25 cm Photoelectric Sensor E3S-LS Focusable Sensors with Built-in DC Amplifiers Pinpoint focusable and area focusable models eliminate background objects. Ideal for precise detection of level/height, edges, small holes and openings, objects touching one another, objects inside transparent covers. Ordering Information Sensing method Sensing distance Model NPN output PNP output Area focusable reflective 5 to 25 cm (continuously variable) E3S-LS20XE4 E3S-LS20XB4 Pinpoint focusable reflective 3 to 10 cm (continuously variable) E3S-LS10XE4 E3S-LS10XB4 3 0.5 cm E3S-LS3C1D E3S-LS3RC4 --- Application Examples E3S-LS10X Sensing of objects utilizing their difference in luster. Sensing of objects traveling in contiguous succession. Sensing of small holes, narrow openings, or unevenness. Pencils E3S-LS20X Sensing of objects utilizing their difference in luster. Sensing of objects traveling in contiguous succession. Sensing of small holes, narrow openings, or evenness. EE E 1 E3S-LS E3S-LS Specifications Ratings/Characteristics Item E3S-LS10Xj4 E3S-LS3C1D E3S-LS3RC4 5 VDC -10% to 24 VDC +10%, ripple (p-p): 10% max. 12 VDC -10% to 24 VDC +10%, ripple (p-p): 10% max. E3S-LS20Xj4 Power supply voltage 12 VDC -10% to 24 VDC +10%, ripple (p-p): 10% max. Current consumption 40 mA max. Sensing distance 3 to 10 cm (variable with distance adjuster) 5 to 25 cm (variable with distance adjuster) 30.5 cm Differential travel 0.5 mm max. at 3 cm 3 mm max. at 10 cm 5% max. --- Standard objects 1 x 1 cm white mat paper 5 x 7.5 cm white mat paper 1 x 1 cm white mat paper Load Model with suffix -E4: Model with suffix -B4: 80 mA max. 100 mA max. 30 mA max. 50 mA max. Voltage output 1.1 V max. at 80 mA 2 V max. Control output ou pu DC solid-state so dsae Response time (ON, OFF) 1 ms max. ON: 3 ms OFF: 100 ms 1 ms max. Sensitivity Adjustable --- Adjustable Operation mode Wire-selectable (Refer to "Output Circuit.") --- Wire-selectable (Refer to "Output Circuit.") Indicators Light indicator (red), stability indicator (green) Operation indicator (red) Light indicator (red) Circuit protection Short circuit Provided Mutual interference protection Provided --- Enclosure rating IEC 144 IP67 IP40 NEMA 1, 3, 4X, 6, 12 --- Housing material Metal Light source Red LED Ambient temperature Operating: -25 to 55 C 2 Plastic Infrared LED Red LED Operating: -10 to 55 C E3S-LS E3S-LS Engineering Data Excess Gain Ratio E3S-LS10XE4 E3S-LS20XE4 E3S-LS3RC4 Peak receiver output at 3 cm Standard sensing object (white paper) Peak receiver output at 10 cm Operating level Sensing distance (cm) Excess gain ratio Excess gain ratio Excess gain ratio Peak receiver output at 5 cm Sensing distance (cm) Note: Setting distance Standard sensing object (black carbon paper) Operating voltage Sensing distance (cm) 1. Sensitivity adjustor: Set to MAX. 2. This graph shows the relationship between the optical output and setting distance by adjusting the sensitivity adjustor so that the optical output will be maximum at a sensing distance of 3, 5, or 10 cm. Operating Range E3S-LS10XE4 E3S-LS3RC4 Standard object (5 x 57.5 cm) Distance: Min. Distance X (cm) Distance: Max. Operating distance x Distance: 3 cm Standard object (1 x 1 cm) Distance: 10 cm Operating position Y (mm) Optical axis Operating position Y (mm) Operating position Y (mm) (with minimum sensing distance) E3S-LS20XE4 Sensing object size: 10 x 10 mm Setting distance (mm) Sensitivity Short side White mat paper Long side Distance (cm) E3S-LS20XE4 Object sensed Ratio of short side to long side = 2:3 Size of object (cm) 3 E3S-LS E3S-LS Operation Output Circuits E3S-LS10X -E4 Type (NPN Output) -B4 Type (PNP Output) +V LightON Brown DarkON +V Blue LightON DarkON Brown Blue Black Black Blue Brown 2.2 Output Main circuit 0V Output Black Black Blue Brown Main circuit 0V E3S-LS20X -E4 Type (NPN Output) -B4 Type (PNP Output) +V LightON Brown DarkON +V Blue LightON DarkON Brown Blue Black Black Blue Brown 2.2 Output Main circuit 0V Output Black Black Blue Brown Main circuit 0V E3S-LS3C1D Operation indicator (red) Photoelectric sensor main circuit +V Brown OUT Black Z 0V Blue Z: Zener diode (V2 = 30 V) E3S-LS3RC4 Light-ON Dark-ON +V Incident indicator (red) OUT Photoelectric sensor main circuit 0V Brown Black Blue Pink 4 Incident indicator (red) Photoelectric sensor main circuit +V Brown OUT Black 0V Blue Pink E3S-LS E3S-LS Timing Chart E3S-LS10X -E4 Type (NPN Output) -B4 Type (PNP Output) Light-ON Dark-ON Incident Interrupted Light Light-ON Light LIGHT indicator ON OFF LIGHT indicator Output transistor ON OFF Output transistor Operates Releases Load (relay, etc.) Load (relay, etc.) Dark-ON Incident Interrupted ON OFF Operates Releases ON OFF H L Output voltage (logic, etc.) E3S-LS20X -E4 Type (NPN Output) -B4 Type (PNP Output) Light-ON Dark-ON Incident Interrupted Light Light-ON Light LIGHT indicator ON OFF LIGHT indicator Output transistor ON OFF Output transistor Operates Releases Load (relay, etc.) Load (relay, etc.) E3S-LS3C1D Output transistor (load) Operates Releases ON OFF E3S-LS3RC4 < T (See note) Indicator ON OFF H L Output voltage (logic, etc.) Sensing object Dark-ON Incident Interrupted Light-ON Light Yes No T (See note) ON OFF ON OFF 3 ms max. Note: Timer setting Timer setting T = 0.1 to 1 s LIGHT indicator ON OFF Output transistor ON OFF Load (relay, etc.) Dark-ON Incident Interrupted Operates Releases (Between brown and black lines) 5 E3S-LS E3S-LS Dimensions Note: All units are in millimeters unless otherwise indicated. E3S-LS10Xj4 E3S-LS20Xj4 Indicator Cord: 4-mm dia., 18/0.12, 3-conductor Standard length: 2 m Weight: approx. 225 g Two, M4 slotted hexagonal bolts Distance adjustor Sensitivity adjustor Lens (14 x 47) (A) (See note) Mounting Holes Emitter Two, M 4 holes Optical axis 8 dia. Receiver 20 Two 4.4 dia. holes Note: A mounting bracket can be attached to side A. E3S-LS3C1D E3S-LS3RC4 Indicator Cord: 4-mm dia., 18/0.12, 3-conductor Standard length: 2 m Weight: approx. 60 g E3S-LS3C1D Timer Volume E3S-LS3RC4 Sensitivity Adjustor 8 dia. Optical axis Two, M3 holes Optical axis 6 E3S-LS E3S-LS Precautions Sensing Distance Adjustment E3S-LS10XE4 E3S-LS20XE4 Adjustment Method 1. Set the pointer of the sensitivity adjuster to the center of its revolution range. 2. Turn the distance adjuster fully counterclockwise to the "S" position. 3. Set the sensing object in position. 4. Turn the distance adjuster gradually clockwise to a point where both the LIGHT and STABILITY indicators light. Fix the distance adjuster at that point. 5. Adjust sensitivity. Adjustment Method 1 When the quantity of light reflected from the object is greater than that from the background object, adjust the sensing distance in the following sequence: 1. Set the pointer of the sensitivity adjuster to the center of its revolution range. 2. Turn the distance adjuster fully counterclockwise to the "S" position. 3. Set the sensing object in position. 4. Turn the distance adjuster gradually clockwise to a point where both the LIGHT and STABILITY indicators light. Fix the distance adjuster at that point. 5. Adjust sensitivity. EE EE E E E Background object Object sensed Distance adjuster EE EE EE EE EE EE Background object Object sensed Distance adjuster Adjustment Method 2 When the quantity of light reflected from the object is greater than that from the background object, adjust the sensing distance in the following sequence: 1. Set the pointer of the sensitivity adjuster to the center of its revolution range. 2. Turn the distance adjuster fully counterclockwise to the "L" position. 3. Remove the sending object. 4. Turn the distance adjuster gradually clockwise to a point where both the LIGHT and STABILITY indicators light. Fix the distance adjuster at that point. 5. Adjust sensitivity. 7 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the product. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: * Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. * Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. * Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ERRORS AND OMISSIONS The information in this catalog has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. COPYRIGHT AND COPY PERMISSION This catalog shall not be copied for sales or promotions without permission. This catalog is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or reproducing this catalog in any manner, for any other purpose. If copying or transmitting this catalog to another, please copy or transmit it in its entirety. Cat. No. E39-E1-3 OMRON Corporation 2007. 3 In the interest of product improvement, specifications are subject to change without notice. Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2007 All Rights Reserved. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: E3S-LS3C1D E3S-LS10XB4 E3S-LS20XB4 E3S-LS20XB4 5M E3S-LS3RC4 E3S-LS3PW-M5J 0.3M