Product Specification
G128240x02 series
Crystal Clear Technology sdn. bhd.
16Jalan TP5—Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia. T: +603 80247099 F: +603 80247098
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
1.0 Table of Contents
Page
1. Table of Contents 1
2. Record of revision 2
3. General specification 3
4. Absolute maximum ratings 4
5. Electrical characteristics 4
6. Environmental requirement 4
7. LCD specification 5 ~ 7
8. Interface 8
9. Timing characteristics / Timing diagrams 9 ~ 10
10. Command Summary 11
11. Block Diagram and Power Supply 12
12. Quality assurance 13 ~ 20
13. Precautions in use LCM 21 ~ 22
14. Outline drawing 23
1
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
2.0 Record of revision
Rev Date Item Page Comment Originator Checked By
1.0
2.0
30/09/08
10.09.09
Initial Release
Update Mechanical Specification
Syam
Khairiah
Azhar
Azhar
2
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
3.0 General specification
Display format: Graphics, 240 (H) x 128 (W)
Pixel size: 0.40 (H) x 0.40 (W) mm
Pixel pitch: 0.45 (H) x 0.45 (W) mm
View area: 64.0 (H) x 114.0 (W) mm
Active area: 57.55 (H) x 107.95 (W) mm
General dimensions: 104.0 (H) x 144.0 (W) x 13.5 max (T) mm
Controller/Driver: T6963 and NT7086 or equivalent
Interface: Parallel
3
Y : Yellow Green (STN)
G : Grey (STN)
B : Black & White (FSTN)
N : Negative (FSTN) Blue ( Single Retardat ion )
U : Negative (FSTN) Black/ White ( Double Retardation )
S : Negative (STN) Purple
L : Negative (STN) Blue
Z : Negative (FSTN) Black/White ( Double Retardation ) TRI-AXIS
SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL)
N : Normal Temperature ( 0°C to +50°C ), where storage temperature is (-20°C to +70°C)
W : Wide Temperature ( -20°C to +70°C ), where storage temperature is (-30°C to +80°C)
00 - STANDARD SPECIFICATION MODEL
REFER TO FACTORY FOR OTHER VERSIONS. TERMS AND CONDITIONS APPLY
SERIES NUMBER FO R THIS ST ANDAR D SPECIFICATIO N
SERIES NUMBER FO R THIS ST ANDAR D SPECIFICATIO N
B : Bottom view ( 6 O'clock )
T : Top view ( 12 O'clock )
OPERATING TEMPERATURE
VIEWING ANGLE
L : Side Led Backlight (Yellow Green)
W : Side Led Backlight (White)
N : No Backlight
BACKLIGHT MODE
STD. GRAPHIC : No. of rows followed by no. of column
MODULE VERSION
MODEL NUMBER
LCD MODE
4
2821
G20 0 0 0
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
4.0 Absolute maximum rating (at Vss = 0V, ambient temperature = 25°C)
NO ITEM SIMBOL MIN MAX UNIT
1. Power Supply voltage (Logic) VDD – VSS 0 7.0 V
2. Power Supply voltage (LCD Driver) VDD – V0- 19.0 V
3. Operating Temperature Top Refer page 3 °C
4. Storage Temperature Tst Refer page 3 °C
5.0 Electrical characteristics
NO ITEM SYMBOL CONDITION MIN TYP MAX UNIT
1. Power Supply
voltage (Logic) VDD – VSS - 4.5 5.0 5.5 V
2. Power Supply
voltage (VLCD) VDD-V025°C 17.5±5% V
3. Input Voltage VIH - VDD –
0.2
- VDD V
VIL - 0 - 0.8
V
mA
4. Current Supply IDD
VDD – VSS =
5.0V - 20 -
5.1 Backlight Options
FORWARD VOLTAGE
(V) FORWARD CURRENT
(mA)
NO COLOR
Min Typ. Max Min Typ. Max
MIN
BRIGHTNESS
(cd/m2) *
1. Yellow Green - 4.5 - - 180 220 30
2. White - 5.0 - - 120 160 110
*Note : 1. Brightness measured at backlight surface.
2. On LCD surface, brightness is only about 10% to 15% of backlight brightness.
3. Lifetime of backlight: For Yellow Green = 50K hrs. For White = 20k hrs.
6.0 Environmental requirements
NO ITEM CONDITION
1. Operating
Temperature
Refer page 3
2. Storage Temperature Refer page 3
3. Operating Humidity 5% to 95%RH
4. Cycle Test 0 C @ 30 min to 50 C @ 30min for 1 cycle
run for 10 cycles
5. Lifetime 50000 HOURS (excluding backlight)
Note: The background on LCD has the possibility to be changed in different temperature range.
4
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
7.0 LCD specification
7.1 Electro-optical characteristics (at ambient temperature = 25°C)
LCD TYPE
UNIT
NO ITEM SYMBOL CONDITION STN
YG STN
GREY
STN
-VE
BLUE/
PURP
LE
FSTN
+VE
B/W
FSTN
–VE
BLUE
FSTN -
VE
TRUE
B/W
FSTN
-VE
TRI
AXIS
REF.
1
Operating
Voltage
(Volt)
VLCD
θ = 0
Cr = max 17.5 ± 5% 7.1.1
θ x 1 +20 +15 +35 +20 +35 +30 +40
θ x 2 -20 -15 -35 -20 -35 -35 -40
θ y 1 -25 -20 -30 -25 -30 -30 -50
2
Viewing
Angle
(Deg)
θ y 2
CR ≥ 2
VLCD =
14.7V +25 +20 +30 +25 +30 +30 +30
7.1.2
3 Contrast
Ratio CR
θ = 00
VLCD
=14.7V
2.5 2.0 5.5 2.5 5.5 15 15 7.1.3
Rise
Time
(Tr)
θ = 00400
4
Response
Time
(msec) Decay
Time
(Td)
θ = 00400
7.1.4
Note:
1. Viewing angle data is based on bottom view product by default. Should it be a
top view product, values are then swap.
2. Contrast ratio is based on typical data when using white colour as backlight.
3. Equipment Used Eldim; Ez Contrast 120R , Spot Size = 2mm
5
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
NO CHARACTERISTICS DEFINITIONS
7.1.1
Definition of Operating
Voltage (VLCD)
VLCD
1/F
VLCD : Operating Voltage
F : Frame Frequency
7.1.2
Definition of Viewing
Angle
TOP
θ REAR
LEFT RIGHT
FRONT
BOTTOM
REAR (θy2)
LEFT(θx2) RIGHT(θx1)
FRONT (θy1)
6
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
7.1.3 Definition of Contrast
Ratio
NON-SELECT WAVE
BRIGHTNESS (%)
SELECT WAVE
b
a
OPERATION VOLTAGE
Contrast Ratio = Brightness of non-selected state (b)
Brightness of selected state (a)
Conditions
(a) Operating Voltage: VLCD
(b) Temperature: 25°C
(c) Viewing Angle, θ = 0o
7.1.4
Response Time
Luminance
(%)
90
10
Tr: Measured between 10% and 90% of LCD segment
maximum response with VON.
Td: With voltage switches to zero and the instant LCD
segment reaches 10% of its maximum response.
Time
Td
Tr
7
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
8.0 Interface
8.1 Controller T6963C
8.2 Display Driver NT7086 or equivalent
8.3 Duty Cycle 1/128
8.4 Pin-out Assignments
Pin No Symbol Description
1 FG Frame ground
2 and 27 VSS Ground terminal of module
3 and 28 VDD Supply terminal of module
4 and 26 VOPower supply for Liquid Crystal Drive
5 /WR Write select (active low)
6 /RD Read select (active low)
7 /CE Chip enable (active low)
8 C/D Command/Data
High = Command register
Low = Data register
9 and 29 NC Non connected
10 /RST Reset (active low)
11 to 18 D0 to D7 Bi-directional Data Bus. Data Transfer is performed
once, thru D0 to D7, in the case of interface data
length is 8-bits.
19 FS Font selection
20 and 25 VOUT Negative voltage from the LCD module
21 and 24 SLA Backlight positive voltage
22 and 23 SLK Backlight ground
30 HSCP Shift clock pulse for column driver of upper area of
LCD.
31 LP Latch pulse for column driver. Shift clock for row
driver.
32 FR Frame signal
33 CDATA Synchronous signal for row driver
34 ED Data input for columns driver
*Font interface format selection :
Font size J1 J2 Pin FS
5x8 Used NC High
6x8 NC* Used* High
7x8 Used NC Low
8x8 NC* Used* Low
Note: NC = Not Connected, * = Factory default setting
8
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
9.0 Timing characteristics / Timing diagrams
9.1 Display Control Timing Waveform and Characteristics
Timing Characteristics between MPU and T6963
9
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
9.2 Relationship between character code and pattern
CG ROM TYPE 0101
CG ROM TYPE 0201
10
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
10. Instruction Set
COMMAND CODE D1 D2 FUNCTION
REGISTER
SETTING
00100001
00100010
00100100
X address
Data
Low address
Y address
00H
High address
Set Cursor Pointer
Set Offset Register
Set Address Pointer
SET CONTROL
WORD
01000000
01000001
01000010
01000011
Low address
Columns
Low address
Columns
High address
00H
High address
00H
Set Text Home Address
Set Text Area
Set Graphic Home Address
Set Graphic Area
MODE SET 1000X000
1000X001
1000X011
1000X100
10000XXX
10001XXX
-
-
-
-
-
-
-
-
-
-
-
-
OR mode
EXOR mode
AND mode
Text Attribute mode
Internal CG ROM mode
External CG RAM mode
DISPLAY MODE 10010000
1001XX10
1001XX11
100101XX
100110XX
100111XX
-
-
-
-
-
-
-
-
-
-
-
-
Display off
Cursor on, blink off
Cursor on, blink on
Text on, graphic off
Text off, graphic on
Text on, graphic on
CURSOR PATTERN
SELECT
10100000
10100001
10100010
10100011
10100100
10100101
10100110
10100111
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1-line cursor
2-line cursor
3-line cursor
4-line cursor
5-line cursor
6-line cursor
7-line cursor
8-line cursor
DATA AUTO READ
/ WRITE
10110000
10110001
10110010
-
-
-
-
-
-
Set Data Auto Write
Set Data Auto Read
Auto Reset
DATA READ /
WRITE
11000000
11000001
11000010
11000011
11000100
11000101
Data
-
Data
-
Data
-
-
-
-
-
Data Write and Increment ADP
Data Read and Increment ADP
Data Write and Decrement ADP
Data Read and Decrement ADP
Data Write and Nonvariable ADP
Data Read and Nonvariable ADP
SCREEN PEEK 11100000 - - Screen Peek
SCREEN COPY 11101000 Screen Copy
BIT SET / RESET 11110XXX
11111XXX
1111X000
1111X001
1111X010
1111X011
1111X100
1111X101
1111X110
1111X111
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
--
Bit Reset
Bit set
Bit 0 (LSB)
Bit 1
Bit 2
Bit 3
Bit 4
-
Bit 5
-
Bit 6
-
Bit 7 (MSB)
-
11
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
11. Block Diagram and Power Supply
LCD PANEL
LED BACKLIGHT
DB0 to DB7
R/W
RD
CE
C/D
RESET
FS
FG
VDD
VSS
VOUT
VO
SLA
SLK
LCD POWER /
CONVERTER
UNIT
SEGMENT
DRIVER
80 SEG.
60 COM
SRAM
D0~D7
AD0~AD14
R/
W
C
E
CONTROL
IC
SEGMENT
DRIVER
SEGMENT
DRIVER
80 SEG.
80 SEG.
COMMON
DRIVER
68 COM.
COMMON
DRIVER
Block Diagram
VDD
VSS
Vout
Vo
5V
LED A
LED K
Power Supply
12
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
12.0 Quality Assurance
12.1 ZONE DEFINITION
12.2 REJECTION CRITERIA
12.2.1 DIMENSIONAL DEFECTS
ZONE A
ZONE B
(Outside Viewing Area)
ZONE C
(Sealing Area)
EFFECTIVE VIEWING AREA
Defect
Category
Defect
Description Criterion Drawing Specification
Glass Size Dimensions of
LCD, do not
conform to the
drawing
Reject Refer to LCD Physical
Dimension Drawing
Perimeter
Seal
Extension
Perimeter seal
epoxy enters the
effective
viewing area
Reject
End Seal
Size
Size of end seal
does not meet
drawing
specification
Reject Refer to LCD Physical
Dimension Drawing
12.2.2 VISUAL DEFECTS
Defect
Category
Defect
Description Criterion Drawing Specification
Fracture A type of
glass
breakage
containing
running
cracks.
Inspectors
should
attempt to
remove it
with
fingernail. If
removed,
evaluate as
chip
Reject – if the
size is > 30%
of the contact
ledge width.
13
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
Defect
Category
Defect
Description Criterion Drawing Specification
Chip Chip in cross
over area
1) Reject - if
the chip
causes
crossover dot
to be exposed
2) Chip on
outside edge
of the glass
plate but is
greater than
50% of glass
thickness at
crossover dot
is reject able.
Chip Chip in
contact pad
area
Accept if:-
a) X ≤ 2.0mm
b) Y ≤ 0.5mm
c) Z disregard
Chip
Epoxy of
crossover dot
exposed
X
Y
Z
Chip in non-
contact pad
area
Accept if:-
a) X ≤ 6.0mm
b) Y ≤ 1.0mm
c) Z disregard
Chip in
perimeter
seal area
Accept if:-
a) Y ≤ 1/3 of
perimeter seal
width (W)
b) X ≤ 3.0mm
c) Z disregard
d) X and Y not
touch
crossover dot
Corner Chip Corner chip
within seal
area
Accept if:-
a) X ≤ 1/3 of
perimeter seal
width (W)
b) Y ≤ 1/3 of
perimeter seal
width (W)
c) Z disregard
Z
X Y
W
Z
Y
X
Y
X
Y
Z
X
Y
X
Z
W
14
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
Defect
Category
Defect
Description Criterion Drawing Specification
Corner chip
not effecting
contact pad /
ITO
Accept if:-
a) XY ≤ 4mm2
AND
b) Y ≤ D and
X ≤ 2.0mm
c) Z disregard
Corner chip
effecting
contact pad /
ITO
A) Accept if:-
a) XY ≤ 4mm2
AND
b) Y ≤ D and
X ≤ 2.0mm
B) Accept if:-
a) X1 ≤
2.0mm
b) Y1 ≤ 0
.5mm
sregard
Z di
Glass flare A thin layer
cept if:-
≤ ¼
≤
: Contact
of glass flare
at contact
area
Ac
a) Flare
thickness
W when W ≤
3mm
b) Flare
thickness
1mm when W
> 3mm
W
ledge width
Glass burr A rough
ft
ge
f
he
r
e
Refer to LCD Physical Dimension
edge(s) le
along the
scribing ed
(i.e. along
the edges o
display)
Reject – if t
burr cause
undersize o
oversize of th
LCD
Drawing
Rainbow Reject – if 3 or
ples
ble)
Colored ring
in sharp
blotches
observed
more colored
rings in sharp
blotches of
color are
observed.
(Limit sam
should be used
when
applica
Y
X
D
Z
D
X1
X Y Y1
Z
A B
15
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
Defect
C
Defect
DCriterion Drawing Specification
ategory escription
Di Re
wing
ufacturing
scoloration ject - if the
discolorations
enter the
active vie
area of LCD.
Color of the
LCD shall
follow product
specification
as specified in
the
man
specification
Air Void LC does not Reject
fulfill the
display
Fill end
ation
ation Reject if
ion
h
ea
e)
contamin
Discolor
at end seal
area
discolorat
exceeded the
baffle (for
display wit
baffle) or
viewing ar
(for display
without baffl
12.2.3 OLARIZER DEFECTS
Category Criterion Drawing Specification
P
Defect Defect Description
Pol
de
1- Polarizer shou ve
viewing area o
older
nce
4- jagged
Ref
Dim
arizer
fect
Polarizer coverage ld cover effecti
f display.
2- It is acceptable if perimeter seal b
at all sides could be seen.
3- It is acceptable if polarizer attaching
position meeting the tolera
mentioned in the drawing.
It is reject able if polarizer edge
and not even
er to LCD Physical
ension Drawing
Polarizer Peeling /
delamination
1- dge or corner of the
polarizer is lifted up or not adheres to
Reject if any e
the glass
Polarizer Scratches 1- Any scratch should be acceptable if it is
t visible from viewing distance at head
it is visible from the
rface
no
of position
2-Polarizer scratch in viewing area is
reject able if
specified viewing distance
3-Defect, which is visible under su
glare, should be disregard
16
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
Defect
Category Defect Description Drawing Specification
Criterion
1-Stain mark or in front
polarizer surface acceptable if it
at
gard
Polarizer damage depression
should be
is not visible from viewing distance
head on position.
2-Defect, which is visible under surface
glare, should be disre
Zone / Acceptable No.
Dimension A B C
D ≤ 0.30mm NC NC
D ≤ 0.50mm 2 NC
0.50 < D ≤
0.60mm 1 2
D > 0.60mm
f
Polarize
u l
0 0
NC i
the
r not
lifted
p/ pee
off
Polarizer bubble /
Foreign material
NC: No count
D: Mean Diameter of Defect
mbers of
3 are the totally permissible nu
bubble
2.2.4 ELECTRICAL TEST DEFECTS
Category Criterion Drawing Specification
1
Defect Defect Description
Mis
co
Reject sing
mmon
Part of the pattern
does not light up
Missing
segment
One or few
segment does not
light up
Reject
Common-
common short connected
Reject Common and
common
Segment-
segment short
Segment and
segment connected
Reject
Common –
segment short
Common and
segment connected
Reject
Wrong
viewing angle ngle
Reject if display viewing angle not
conform to customer requirement
Wrong viewing
a
Metal residue up
order of the
) Extra spot lights
at the b
segment.
Accept if ≤ 0.20mm (mean diameter
Slow
response one side
Reject if it is visible at 30cm distance
Response of the
display on
slower than the
other side
A
B
D = (A + B)/2
17
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
Defect
Category Defect Description Criterion Drawing Specification
Zone /
imension Acceptable No.
D
- 1 per pixel/dot
Located inside
dot:-
single pixel/
(X + Y)/2 ≤
0.20mm
- 3 per display
(Active Area)
- 1 per pixel/dot Laid over the p
pixel/dots:
lural
(X + Y)/2 ≤
0.20mm
- 3 per display
(Active Area)
Pin
art of do
or display)
Hole Pin hole / void at
light up segment
(¾ or larger p
effective f t area has to be
Y
X
Lacked
deformation
Accept if:
i) X ≤ 0.15 and
ii) Y ≤ 0.15
X
Deformed
display dot
Added deformation
ccept if:
X < 0.02 and
Y
A
i)
ii) Y < 0.02
X
Y
Reverse twist/ Segment are darke
tilt
r
or clearer than
eject
R
other area of the
same segment
Misalignment
Reject if > 10% of designed segment
width and visible at 30cm distance
Segment fatter or
smaller or extra
segment
Segment
Smearing
t Light up segmen
smear
Reject
Dim segment
rast at pre
Display shows
poor cont
set voltage
Reject
18
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
12.2.5 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (SOLID FIGURE)
Category wing Specification
Defect Defect Description Criterion Dra
Zone / ceptable No. Ac
Dimension A B C
D < 0.10mm N
C NC NC
0.10<D < 0.15mm 3 3 NC
0.15 < D < 0.25mm 1 2 NC
0.25 < D < 0.35mm 1 1 NC
D > 0.35 mm 0 0 NC
NC: No count
Black Spot,
W
eter of Defect
hite Spot
and Foreign
Material
Black Spot, White
Spot and Foreign
Material
A
B
D = (A + B)/2
D: Mean Diam
NOTE: The 1/3 or larger parts of indivi
The solid figure is that the defect has clear-cut outline at the optimum driving condition in both positive
s.
2.2.6 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (FADED FIGURE)
Category ing Specification
dual dot has to be lighted on.
and negative, of which size does not change when the contrast change
1
Defect Defect Description Criterion Draw
Zone / ble No. Accepta
Dimension A B C
D < 0.60mm N
C NC NC
0.60<D < 0.70mm 3 NC
0.70 < D < 0.80mm 1 NC
D > 0.80 mm 0 NC
NC: No count
Black Spot,
W
eter of Defect
hite Spot
and Foreign
Material
Black Spot, White
Spot and Foreign
Material
A
B
D = (A + B)/2
D: Mean Diam
NOTE: Faded figure means that the defe timum driving condition in both
positive and negati of which size seems to change when the contrast changes.
cts has unclear outline at the op
ve,
19
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
12.2.7 LINE SHAPE AND SCRATCHES
Category Criterion Drawing Specification
Defect Defect Description
Zone /Dimensio ceptable No. n Ac
X Y A B C
NC ≤
0.0 m
3m NC NC NC
≤ 2
mm
≤
0.05mm
1 1 NC
≤ 1
mm
≤
0.10mm
1 2 NC
NC ≥
0.10mm
Due to ( u
defect
1) ro nd
Lin
an
e shape
d scratches
Line shape and
scratches
NOTE: Length is X and Width is Y.
REMARK:
i) Total amount of spot defects including round and linear – A total of 5 permissible numbers of defects
Zone A & B including above (14.2.5), (14.2.6), (14.2.7). Regardless of number of defects, the
termined by the “Limit
tandard” sample, which were occasionally set up with the mutual consent of both parties. In every
the
in
minimum distance between individual defects have to be 5mm or larger.
ii) All the other items of inspection that are not included herein must be de
S
case of the items set up with the Limit Standard, the Limit Standard always takes precedence over
other means of definition.
20
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
13. recaution for using LCM P
1. Liquid Crystal Display (LCD)
e) Avoid pressing on the metal bezel,
2.2 Static E
b)
e)
f)
2.3 Solder
y to the I/O terminals.
c) °C
in flux fill.
e
LCD is ade up of glass, organic sealant, orgmanic fluid and
b)
c)
d)
Cr
justed with a high
c)
d)
any of the elements.
otherwise the elastomer connector
could be deformed and lose contact,
resulting in missing pixels.
lectricity
polymer based polarizers. The following precautions should
be taken when handling.
a) Keep the temperature within the range of use and
storage. Excessive temperature and humidity
could cause polarization degredation, polarizer
peel off or bubble.
Do not contact the exposed polarizer with
LCM contains CMOS LSI’s and the same
precaution for such devices should apply, namely
a) The operator should be grounded whenever
anything harder than HB pencil lead. To clean
dust off the display surface, wipe gently with
cotton, chamois or other soft material soaked in
petroleum benzin.
Wipe off saliva or water drops immediately.
he/she comes into contact with the module.
Never touch any of the conductive parts
such as the LSI pads, the copper leads on the
PCB and the interface terminals with any
parts of the human body.
The modules should be kept in antistatic
Contact with water over a long period of time
may cause polarizer deformation or colour
fading, while an active LCD with water
condensation on its surface will cause corrosion
of ITO electrodes.
Glass can be easily chipped or cracked from
bags or other containers to static for storage.
c) Only properly grounded soldering irons
should be used.
d) If an electric screwdriver is used, it should
be well grounded and shielded from
commutator spark.
The normal static prevention measures
rough handling, especially at corners and edges.
e) Do not drive LCD with DC voltage.
should be observed for work clothes and
working benches, the latter conductive
(rubber) mat is recommended.
Since dry air is inductive to statics, a relative
2. Liquid ystal Display Modules.
2.1 Mechanical Considerations
LCM are assembled and ad
degree of precision. Avoid excessive shocks and
do not make any alterations or modification. The
following should be noted.
a) Do not tamper in any way with the tabs
humidity of 50-60% is recommended.
ing
a) Solder onl
on the metal frame.
b) Do not modify the PCB by drilling b) Use only soldering irons with proper
grounding and no leakage.
Soldering temperature: 280
extra holes, changing its outline,
moving its component or modifying its
pattern.
Do not touch the elastomer connector,
d) Soldering time: 3 to 4 sec
e) Use eutectic solder with res
f) If flux is used, the LCD surface should b
especially insert a backlight panel (for
example, EL)
When mounting a LCM make sure that
covered to avoid flux spatters. Flux residue
should be removed afterwards.
the PCB is not under any stress such as
bending or twisting. Elastomer contacts
are very delicate and missing pixels
could result from slight dislocation of
21
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G128240x02xxx00 REV 2.0
22
2.4 Operation
b) be kept within
c) e increases with decrease in
d) turn black or dark blue at
e) isturbance during operation (
.5 Storage
amage glass cell,
.6 Limited Warranty
etween Crystal Clear
Technology and customer, Crystal Clear
Technology will replace or repair any of its LCD
and LCM which is found to be defective
electrically and visually when inspected in
accordance with Crystal Clear Technology
acceptance standards, for a period of one year
from date of shipment. Confirmation of such date
shall be based on freight documents. The
warranty liability of Crystal Clear Technology is
limited to repair and/or replacement on the terms
set forth above. Crystal Clear Technology will
not responsible for any subsequent or
consequential events.
Unless otherwise agreed b
2
wash off any human part that comes into contact
with soap and water. Never swallow the fluid.
The toxicity is extremely low but caution should
be exercised at all the time.
If any fluid leaks out of the d
2
a) The contr
such as pressing on the viewing area) may
cause the segments to appear “fractured”.
temperature above its operational range, this
is (however not pressing on the viewing
area) may cause the segments to appear
“fractured”.
Mechanical d
temperature.
Display may
specified range, excess voltage shortens
display life.
Response tim
LCD driving voltage V0
Driving voltage should
as can be adjusted by varying the
Crystal Clear Technology
16 Jalan TP5—Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia