Card Edge Connectors (Solder Type, Board-to-Board) ACTION PIN Press-Fit Contacts The Reliable Plated ThroughHole Interconnect Solderless interconnections have been popular in electrical and electronic application with world-wide success for decades. They provide reliable electrical and mechanical stability and offer applied-cost savings across the board. For PC board applications, ACTION PIN contacts from Tyco Electronics provide these features: n Large gas-tight contact zone n Reliability due to stored energy in compliant pin contacts n No damage to plated through-holes during installation * Solder spots; short circuits between printed circuits Principle of the Tyco Electronics Compliant ACTION PIN Contact n Especially suited for multilayer PC boards * Flux residuals When an ACTION PIN contact is inserted into a plated through-hole, two spring members are compressed, exerting force against the hole for gas-tight connection. The diameter of the hole is smaller than the diagonal size of the pin (see cross-section illustration below). n Less costly board manufacturing due to larger hole tolerances compared to use of solid pins n Application can be made by end-user n Repairability--contact can be replaced in the same pin location (two repairs) n Installation with no heat cycling of board n Permits mass insertion by minimizing forces needed to insert pins as compared to solid pin press-fit application n Significant applied-cost savings in many applications Since ACTION PIN contacts do not have to be soldered, issues associated with solder are eliminated, such as: * Faulty solder joints * Solder fumes; contaminant's are deposited on the contacts * Thermal strain on printed circuit boards and components * Degasing of plated through-holes Solderless press-fit interconnections using the ACTION PIN contact are primarily integrated in, but not limited to, backplanes. Solderless press-fit interconnections are used in racks, especially where connectors must be fixed on the solder side of the PC board and/or component side. In these applications, the holes for ACTION PIN contact connectors are covered during the soldering process and press-fitting is performed after soldering. Other applications for ACTION PIN contact interconnections include PC boards that incorporate components using surface mount technology (SMT). Here, too, press-fit interconnections can be applied after soldering, thus eliminating complications associated with connectors suitable for surface mounting. The beam characteristics of the pin are designed so that a plastic, as well as an elastic, deformation takes place during insertion. The two spring members compress to different degrees Minimum Hole Dia. .037 [0.94] to accommodate hole tolerances. The compliant pin also reduces strain on the board. With a rigid pin, the elastic strain energy is stored entirely in the board, leading to damage of the plated through-holes. With the ACTION PIN contact, the residual force of the elastic deformation maintains stored energy to produce a tight contact zone between the pin and the plated through-hole. This provides long term electrical and mechanical reliability of the interconnection. Maximum Hole Dia. .043 [1.09] Cross-Section Area from Tyco Electronics ACTION PIN Press-Fit Contact in Printed Circuit Board Holes from Tyco Electronics. Note: ACTION PIN contact mounting hole specifications are presented in each product section, where applicable. 97 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors Performance Specifications Electrical Characteristics Contact Resistance: ACTION PIN Contact Interface--5 milliohm Spring Contact to Test Board--11.5 milliohms Total Circuit Resistance: 12 milliohms Continuous Current Rating*: 3 amperes Insulation Resistance: 5,000 milliohms Dielectric Withstanding Voltage: .100 [2.54] Centerline Spacing-- 1,000 VAC at sea level; 350 VAC at 50,000 ft. [15,240 m]; 275 VAC at 70,000 ft. [21,336 m] .125 [3.18] Centerline Spacing-- 1,500 VAC at sea level; 500 VAC at 50,000 ft. [15,240 m]; 235 VAC at 70,000 ft. [21,336 m] Physical Characteristics Card Insertion Force (Max.): 16 oz [4.45 N] per contact pair ACTION PIN Contact Post Card Extraction Force (Min.): 1 oz [.278 N] per contact pair ACTION PIN Contact Post Retention (in PC board): .100 x .100 [2.54 x 2.54]-- 7.5 lb. [33.4 N] min. Operating Temperature: -55C to +85C Durability: Tested to 100 cycles (100 insertions and withdrawals at a rate not exceeding 10 cycles per minute) Salt Spray: MIL-STD-1344, Method 1001 Physical Shock: MIL-STD-1344, Method 2004 Thermal Shock: MIL-STD-1344, Method 1003, Cond. A AMP PACE (Pre-Assembled Card Edge) Connectors are the latest innovation in the evolution of backplane architecture. Designed to shorten manufacturing time and reduce applied costs, these one-step, pre-assembled connectors are ready for mounting and mass insertion. In addition, design features such as removable housings and contacts, that Humidity: MIL-STD-1344, Method 1002, Type II are replaceable through the top of the connector housing, for maximum flexibility in your backplane packaging. At the heart of the AMP PACE Connector is AMP's proven and reliable ACTION PIN Contact. This unique contact has superior electrical and physical characteristics that are top of the line in the industry. AMP PACE Connectors are available with post centerline spacings of: .100 x .100 [2.54 x 2.54] .100 x .200 [2.54 x 5.08] .125 x .125 [3.18 x 3.18] .125 x .250 [3.18 x 6.35] .156 x .200 [3.96 x 5.08] Important: Application tooling is absolutely necessary to insert connectors into PC boards. See page 115 for application tooling. Vibration: MIL-STD-1344, Method 2005 Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR7189 *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 98 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors (Continued) Product Facts Repairability-- (See below for details) Individual contacts can be removed without removing the housing; housings can be removed without removing posts. Important: APC board must be inserted into the connector when removing the contact. Precision Plated Contacts-- Selective plating puts gold where it is needed for superior electrical contact at a reasonable cost. Beam Contact Design-- The contact's unique beam design accommodates and compensates for daughter board warp and stress providing long-term, reliable performance (100 gram minimum normal force). Gas-Tight Connection-- Spring sections of ACTION PIN Contacts compress in opposite directions, maintaining a gas-tight fit with the PC board. Contact Tip Alignment Strip-- Polyester strip provides straight and stable pin alignment for damage-free entry into the PC board. Precision Plated Post-- Gold plating can be applied to the entire post, or just the post tip for improved pluggability. Repairability Details Remove and replace contacts without removing housing. (See page 115 for Contact Replacement Tools.) Remove and replace housing without removing contacts. 99 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline Standard Housing .100 [2.54] .380 [9.65] .040 Min. [1.02] Contact Finish Area B C .006 [0.15] .415 [10.54] Card Slot Depth .005/.007 [0.13/0.18] See E Below Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .475 [12.07] Post Length .025 Sq. [0.64] Post .100 [2.54] A .100 [2.54] Typical Closed End/ Open End Housings .100 [2.54] Connectors can be mounted in pairs using any size combinations. Example: 1-30 pos. + 1-60 pos. = 1-90 pos. .135 [3.43] Detail E Keying Plugs On-Contact (Plastic) Part No. 119802-2 Intercontact (Plastic) Part No. 118982-1 100 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Material and Finish: Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. No. of Dual Positions A Dimensions B C 15 1.400 35.56 1.734 44.04 1.604 40.74 31 1.900 48.26 2.400 60.96 2.700 68.58 3.000 76.20 2.234 56.74 2.734 69.44 3.034 77.06 3.334 84.68 2.104 53.44 2.604 66.14 2.904 73.76 3.204 81.38 35 3.400 83.36 3.734 94.84 3.604 91.54 3.900 99.06 4.700 119.38 4.900 124.46 5.900 149.86 4.234 107.54 5.034 127.86 5.234 132.94 6.234 158.34 4.104 104.24 4.904 124.56 5.104 129.64 6.104 155.04 20 25 28 40 Related Product Data: Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 48 50 60 Post Length .180 4.57 .475 12.07 .180 4.57 .180 4.57 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .180 4.57 .180 4.57 Closed/Closed Standard Scoop Closed/Open Standard 119734-1 119736-1 -- 119237-1 -- -- 119734-6 -- -- 1-119734-1 -- -- 1-119734-4 -- -- 1-119237-7 -- -- 2-119734-1 -- 119831-6 -- -- 119413-6 2-119734-6 2-119736-6 -- 3-119237-4 -- -- 3-119734-6 -- -- 4-119734-6 4-119736-6 -- Note: Other connector sizes and connectors with card scoops can be made available, consult Tyco Electronics. Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2978, 408-2979, 408-6881, 408-9091, 408-9188 101 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline Standard Housing .100 [2.54] .364 [9.24] .360 [9.14] B .006 [0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .200 [5.08] A .100 [2.54] Housing with High Card Scoops .100 [2.54] .390 [9.91] B C .006 [0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards A Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .200 [5.08] .100 [2.54] Keying Plugs Intercontact (Plastic) Part No. 118982-1 .135 [3.43] On-Contact (Plastic) Part No. 119802-2 Detail E 102 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Material and Finish: Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. No. of Dual Positions A Dimensions B C 20 .900 22.86 1.400 35.56 1.700 43.18 1.900 48.26 1.234 31.34 1.734 44.04 2.034 51.66 2.234 56.74 1.104 28.04 1.604 40.74 1.904 48.36 2.104 53.44 22 2.100 53.34 2.434 61.82 2.304 58.52 24 2.300 58.42 2.634 66.90 2.504 63.60 25 2.400 60.96 2.734 69.44 2.604 66.14 2.700 68.58 3.034 77.06 2.904 73.76 30 2.900 73.66 3.234 82.14 3.104 78.84 31 3.000 76.20 3.100 78.74 3.334 84.68 3.434 87.22 3.204 81.38 3.304 83.92 34 3.300 83.82 3.634 92.30 3.504 88.90 35 3.400 86.36 3.734 94.84 3.604 91.54 36 3.500 88.90 3.834 97.38 3.704 94.08 37 3.600 91.44 3.934 99.92 3.804 96.62 40 3.900 99.06 4.234 107.54 4.104 104.24 4.200 106.68 4.300 109.22 4.534 115.16 4.634 117.70 4.404 111.86 4.504 114.40 50 4.900 124.46 5.234 132.94 5.104 129.64 55 5.400 137.16 5.734 145.54 5.604 142.34 60 5.900 149.86 6.234 158.34 6.104 155.04 10 15 18 Related Product Data: Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 Technical Documents: 28 32 (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9058, 408-9067, 408-9091, 408-9186 43 44 Post Length .180 4.57 .180 4.57 .180 4.57 .180 4.57 .180 4.57 1.475 12.07 .180 4.57 .180 4.57 .702 17.83 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .180 4.57 .180 4.57 .475 12.06 .475 12.06 .180 4.57 .475 12.06 .180 4.57 .180 4.57 .475 12.06 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .180 4.57 .702 17.83 Closed End/Closed End Standard High Scoop -- 1-650297-1 1-119738-1 119791-1 1-119738-4 -- 1-119738-6 -- 1-119738-8 -- -119216-8 650123-8 1-119738-0 -- 1-119738-1 -- 1-119163-1 -- 1-119738-4 -- 1-119216-4 -- 1-119738-6 1-119791-6 1-119216-6 -- 1-119163-6 -- 1-119738-7 -- 1-650122-8 -- -- 2-119791-0 2-119216-0 -- 2-119216-1 -- 2-119738-2 -- 2-119216-2 -- 2-650122-3 -- 2-119738-6 -- 2-119216-6 -- 2-650122-9 -- 3-119216-0 -- 3-119738-6 3-119791-6 3-119216-6 -- -- 3-119726-6 4-119738-1 4-650124-1 4-119738-6 -- 119677-1 -- Note: Other connector sizes can be made available, consult Tyco Electronics. 103 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .125 x .125 [3.18 x 3.18] Centerline Material and Finish: Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. palladiumnickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D Housing with High Card Scoops 28 Dual Positions Part Number 1-119853-4 3.625.006 [92.080.15] .005/.007 [0.13/0.18] Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. .515 [13.08] Card Slot Depth .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards 3.375 [85.72] Contact Tip Alignment Strip and .702 [17.83] Post Length .364 [9.24] .040 Min. [1.02] Contact Finish Area See E Below Related Product Data: Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 .420 [10.67] .125 [3.18] 3.755 [95.38] .025 Sq. [0.64] Post .125 [3.18] .125 [3.18] Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6727, 408-9186 .135 [3.43] Detail E Keying Plugs Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 104 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connector Specials, .125 x .125 [3.18 x 3.18] Centerline 27 Dual Positions Tin-Lead Posts .634 [16.10] Long Part No. 645394-1 18 or 36 Dual Positions Tin-Lead Posts .740 [18.80] Long Part No. 119552-2 Tin-Lead Posts .180 [4.57] Long Part No. 119880-1 97 Dual Positions (Two-piece Closed End/Open End with Partial Card Scoops and Card Guides) Contact Tyco Electronics for specific Part Number information. 105 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline Standard Housing .125 [3.18] .364 [9.24] .410 [10.41] B .006 [0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area .702 [17.83] Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .250 [6.35] A .125 [3.18] Housing with High Card Scoops .125 [3.18] .420 [10.67] B C .006 [0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths 3.375 [85.72] .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .250 [6.35] .125 [3.18] Typical Closed End/ Open End Housings Keying Plugs .125 [3.18] Intercontact (Plastic) Part No. 118982-1 Connectors can be mounted in pairs using any size combinations. .135 [3.43] Example: 1-30 pos. + 1-60 pos. = 1-90 pos. Detail E On-Contact (Plastic) Part No. 119802-2 106 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline (Continued) Material and Finish: Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: No. of Dual Positions A Dimensions B C 18 2.125 53.98 2.373 60.27 2.505 63.63 22 2.625 66.68 3.005 76.33 2.875 73.02 25 27 3.000 76.20 3.250 82.55 3.380 85.85 3.630 92.20 3.250 82.55 3.500 88.90 28 3.375 85.72 3.755 95.38 3.625 92.08 3.625 92.08 4.005 101.73 3.875 98.24 36 4.375 111.82 4.755 120.78 4.625 117.48 38 4.625 117.47 4.873 123.77 5.005 127.13 40 4.875 123.83 5.255 133.48 5.125 130.18 50 6.125 155.58 6.250 158.75 7.375 187.33 6.505 165.23 6.630 168.40 7.755 196.98 6.375 161.93 6.500 165.10 7.625 193.68 30 Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 51 Technical Documents: (pages 186, 187): 60 Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9063, 408-9091, 408-9119, 408-9186 Post Length .180 4.57 .180 4.57 .500 12.70 .702 17.83 .180 4.57 .702 17.83 .180 4.57 .500 12.70 .180 4.57 .500 12.70 .180 4.57 .500 12.70 .180 4.57 .180 4.57 .702 17.83 .180 4.57 .500 12.70 .180 4.57 Closed End/Closed End Standard High Scoop Closed End/Open End High Scoop 1-119822-4 -- 3-119840-2 1-119822-8 -- -- 1-119200-8 -- -- 1-119202-8 -- -- 1-119822-1 -- -- 1-119202-3 -- -- 1-119822-4 -- -- 1-119200-4 -- -- 1-119822-6 1-678034-1 -- -- 1-119841-6 -- 2-119822-2 1-678034-2 -- -- 2-119841-2 -- 2-119822-4 -- 3-119840-9 2-119822-6 -- -- 2-119200-6 -- -- 3-119822-6 -- -- 3-119200-7 -- -- 4-119822-6 -- -- Note: Other connector sizes can be made available, consult Tyco Electronics. 107 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make Before Break Contacts Standard Housing .125 [3.18] .364 [9.24] .410 [10.41] B .006 [0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area .702 [17.83] Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .250 [6.35] A .125 [3.18] Housing with High Card Scoops .125 [3.18] .420 [10.67] B C .006 [0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths 3.375 [85.72] .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .250 [6.35] .125 [3.18] Typical Closed End/ Open End Housings Keying Plugs .125 [3.18] Intercontact (Plastic) Part No. 118982-1 Connectors can be mounted in pairs using any size combinations. .135 [3.43] Example: 1-30 pos. + 1-60 pos. = 1-90 pos. Detail E On-Contact (Plastic) Part No. 119802-2 108 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make Before Break Contacts (Continued) Material and Finish: Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D No. of Dual Positions 18 24 A Dimensions B C Post Length Closed End/Closed End Standard Closed End/Open End High Scoop 2.125 53.98 2.875 76.20 2.505 63.63 3.123 79.25 2.373 60.27 3.058 77.67 .180 4.57 .180 4.57 1-1571235-1 -- -- 650059-2 Note: Other connector sizes can be made available, consult Tyco Electronics. Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9063, 408-9091, 408-9119, 408-9186 109 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline Material and Finish: Standard Housing Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D .156 [3.96] B C .006 [0.15] .005/.007 [0.13/0.18] Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 .415 [10.54] Card Slot Depth See E Below .040 Min. [1.02] Contact Finish Area Post Length and Finish Area Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: .364 [9.24] .360 [9.14] Accepts .054 to .071 [1.37 to 1.80] PC Boards A .156 [3.96] Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths .025 Sq. [0.64] Post .545 [13.84] .093 Min. [2.36] .200 [5.08] Keying Plugs Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6726, 408-9186 Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 .135 [3.43] Detail E No. of Dual Positions A Dimensions B C 15 2.184 55.47 2.626 66.70 2.495 63.39 18 2.652 67.36 3.094 78.59 2.964 75.29 22 3.276 83.21 3.718 94.44 3.588 91.13 28 43 4.212 106.98 6.552 166.42 4.654 118.21 6.994 177.65 4.524 114.91 6.864 174.35 Post Length Closed End/Closed End Standard .180 4.57 .475 12.07 .702 17.83 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .475 12.07 .702 17.83 1-119790-1 1-119254-1 1-119256-1 1-119254-4 1-119790-8 1-119254-8 1-119256-8 1-119790-4 1-119254-4 1-119256-4 2-119790-9 2-119254-9 2-119256-9 Note: Other connector sizes can be made available, consult Tyco Electronics. 110 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline w/Make Before Break Contacts Material and Finish: Card Scoop Housing Housing--Black glass-filled polyester, 94V-0 rated Contacts--Phosphor bronze, plated gold flash over .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip--Clear polyester, type D .156 [3.96] .364 [9.25] B .045 Contact Area [1.14] C .116 Contact Area [2.95] Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Performance Specifications-- page 98 Accessories--page 112 PC Board Edge Pattern--page 113 ACTION PIN Contact Mounting Hole Specifications--page 114 Application Tooling--page 115 Contact Replacement Tools-- page 115 Special Application--page 96 Technical Documents: .200 [5.08] .005/.007 .093 Min. [0.13/0.18] [2.36] Accepts .054 to .071 [1.37 to 1.80] PC Boards Related Product Data: .228 [5.78] A .156 [3.96] Keying Plugs (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6726, 408-9186 Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 .135 [3.43] Detail E No. of Dual Positions A Dimensions B C Post Length Closed End/Closed End Scoop 18 2.652 67.36 3.094 78.59 2.964 75.29 .180 4.57 678035-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 111 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Accessories for AMP PACE Connectors Connector Card Guide Material: Black glass-filled polyester Hole for #4 Self-Tapping Screw (mandatory) .050 [12.7] Deep Related Product Data: Mates with all standard housings (will not mate with some special housings) .370 [9.4] L Technical Documents: .410 [10.41] (pages 186, 187): .220 [5.59] Instruction Sheet 408-9091 .152 Dia. [3.96] (2 Holes) B Dimension from AMPPACEConnector Tables Plus .310 [7.87] L1 2.500 63.50 6.000 152.40 Part Numbers 1-117169-3 1-117169-3 1Other lengths up to 6.0 [152.4] can be made available. Consult Tyco Electronics for details. Ground Module Accepts .054 to.071 [1.37 to 1.80] PC Board Rating: 20 amperes per contact--Copper or aluminum bus .420 [10.67] Material and Finish: Housing--Black glass-reinforced thermoplastic Contact--CA 195, 3/4 hard, plated .000050 [0.00127] gold in contact area (front face only); .000100 [0.00254] tinlead on post, with entire contact underplated .000050 [0.00127] nickel .455 [11.56] .700 [17.78] Related Product Data: Mates with all standard housings (will not mate with some special housings) .060 [1.52] Contact Area .250 [6.35] .300 [7.62] Technical Documents: (pages 186, 187): Part No. 119341-1 Seating Tool 59881-1 Instruction Sheet 408-2978 112 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) PC Board Layout for AMP PACE Connectors Recommended PC Board Edge Pattern Gold Fingers .040 +.020 -.010 [1.016+.508 -.254 ] .430 [10.92] 30 .275 [6.99] .050 [1.27] Max. Chamfer B C .052.002 [1.320.05] Key Slot .005 [0.13] .054-.071 [1.37-1.80] A1 1A Max. = Minimum connector card slot -.001 [-0.03]. A Min. = Minimum connector card slot -.011 [-0.28]. Note: Finger pattern to be centered on daughter card. Each finger can deviate .003 [0.08] from true position. AMP PACE Connector Centerline Spacing .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 .156 x .200 3.96 x 5.08 Dimensions B .100 2.54 .100 2.54 .125 3.18 .125 3.18 .156 3.96 C .070 1.78 .070 1.78 .080 2.03 .080 2.03 .080 2.03 113 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today's standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. Annular Ring (See Note) Drilled Hole Copper Thickness Tin-Lead Thickness Plated Through-Hole Mounting Hole Specifications Connector No. of Dual Centerline Positions .125 x .125 28, 97 3.18 x 3.18 .156 x .200 15-43 3.96 x 5.08 .125 x .125 3.18 x 3.18 27 .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 15-60 15-60 18, 36 ACTION PIN Contact Material Thickness Drilled Hole Diameter .025 0.64 .0453.001 1.1510.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 Not Specified Not Specified .025 0.64 .0465.001 1.1810.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 Not Specified Not Specified .025 0.64 .0453.001 1.1510.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 .0015 0.038 .002 0.05 Plating Thicknesses Copper* Tin-Lead Plated Through-Hole Diameter Radial Hole Distortion Average Maximum 18-60 *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 114 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Application Tooling for AMP PACE Connectors Modular Seating Tools Available from Tyco Electronics is a complete series of AMP PACE Modular Seating Tools for installing AMP PACE Connectors on printed circuit boards and panels. These tools are modular in design in that housing tool holders may be added or subtracted to accommodate several different connector sizes. In addition, all tool parts are individually replaceable should the tool become damaged. Modular seating tools are supplied in two basic designs: One which covers all connector centerlines except .100 x .100 [2.54 x 2.54] and one for the .100 x .100 [2.54 x 2.54] centerline connectors. All seating tools have a common shut height of 1.5 inches [38]. This allows AMP PACE and other ACTION PIN products to be seated at the same time on AMP seating machines. See page 149 for a description of the AMP seating machines. .100 x .100 [2.54 x 2.54] Centerline Spacing .100 x .200 [2.54 x 5.08], .125 x .125 [3.18 x 3.18], .125 x .250 [3.18 x 6.35], For Connectors without Scoops No. of Dual Positions 15 18 20 22 25 28 30 31 32 34 35 36 37 40 43 44 48 50 51 54 55 56 60 .156 x .200 [3.96 x 5.08] Centerline Spacing Centerline .100 x .100 [2.54 x 2.54] 1-58200-1 -- 1-58200-6 -- 1-58200-1 1-58200-4 1-58200-6 1-58200-7 -- -- 2-58200-1 -- -- 2-58200-6 -- -- 3-58200-4 3-58200-6 3-58200-7 4-58200-0 4-58200-1 -- 4-58200-6 .100 x .200 [2.54 x 5.08] 1-58140-1 1-58140-4 1-58140-6 1-58140-8 1-58140-1 1-58140-4 1-58140-6 -- 1-58140-8 2-58140-0 2-58140-1 2-58140-2 2-58140-3 2-58140-6 2-58140-9 3-58140-0 -- 3-58140-6 -- -- 4-58140-1 -- 4-58140-6 .125 x .250 [3.18 x 6.35] -- 1-58142-4 -- 1-58142-8 1-58142-1 1-58142-4 1-58142-6 -- -- -- -- 2-58142-2 -- 2-58142-6 -- -- -- 3-58142-6 3-58142-7 -- -- 4-58142-2 4-58142-6 .156 x .200 [3.96 x 5.08] 1-58143-1 -- -- 1-58143-8 -- 1-58143-4 -- -- -- -- -- -- -- -- 2-58143-9 -- -- -- -- -- -- -- -- For Connectors with Scoops No. of Dual Positions 15 18 22 28 30 38 50 55 Contact Replacement Tools Centerline Replacement tools listed in the chart at the right are used to install replacement contacts in AMP PACE connector housings. Replacement Tool 1-265871-7 is used to remove all .025 [0.64] square posts from PC boards. .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 .156 x .200 3.96 x 5.08 .100 x .200 [2.54 x 5.08] 1-58150-1 -- 1-58150-8 -- 1-58150-6 -- 3-58150-6 4-58150-1 Standard Centerline .125 x .125 [3.18 x 3.18] -- -- -- 1-58218-4 -- -- -- -- .125 x .250 [3.18 x 6.35] -- 1-58184-4 -- -- -- 2-58184-4 3-58184-6 -- Housing Style Full Card Scoop 266220-3 -- 266220-1 58210-1 -- 58210-4 266220-2 58210-2 266220-2 -- Note: Tooling availability is dependent upon part number activity. Consult Tyco Electronics for further information. 115 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors Product Facts High density - .0625 [1.586] contact centerlines Compliant ACTION PIN contacts press-fit into plated-through holes for solderless application Individually replaceable contacts Accommodates up to three levels of daughter card pads for sequencing .125 [3.18] square grid post arrangement Performance Specifications Current Rating*: 3 amperes max. Mating Force (Contact Pair): 1 lb. [4.4 N] max. Durability (Mating Cycles): 100 min. Termination Resistance: 12 milliohms max. Dielectric Rating: 1200 VAC (rms) Insulation Resistance: 5000 megohms max. The high performance AMP TELEDENSITY connector is a high density, card edge, telecommunications connector. It features compliant ACTION PIN contacts for solderless application to multi-layer printed circuit boards with plated-through or bare copper holes. These connectors accept .054 to .072 [1.37 to 1.83] thick daughter cards. To satisfy the broadest range of application needs, the Operating Temperature: -55C to +85C contacts are plated with 30 microinches of gold in the mating area and tin-lead on the posts. A plastic locating strip keeps posts positioned correctly for board insertion. For high-density needs, TELEDENSITY connectors offer a .0625 [1.586] daughter card contact centerline spacing in 39-, 71-, or 99dual positions. The connector's .330 [8.38] slot depth accommodates up to three levels of daughter card pads for sequencing, while a biasing wedge maintains proper pad alignment during card extraction. Posts are arranged in a .125 [3.18] square grid to ease circuit routing. *Consult Tyco Electronics when paralleling contacts for power applications. 116 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors, .0625 [1.586] Centerline Material and Finish: Housing--Black polyester Contacts--Copper alloy 725, plated .000030 [0.00076] gold in contact area, .000030 [0.00076] solder plate on post, with entire contact underplated .000100 [0.00254] nickel Coil Spring--Stainless steel Contact Tip Alignment Strip--Clear polyester Related Product Data: Performance Specifications-- page 116 ACTION PIN Contact Mounting Hole Specifications--page 118 Technical Document--pages 186, 187 Product Specification-- 108-26003 Instruction Sheet-- 408 6866 Number of Dual Positions 39 71 99 Dimensions A B 3.168 80.47 2.588-2.600 65.74-66.04 5.168 131.27 6.918 175.72 4.588-4.600 116.54-116.84 6.338-6.350 160.99-161.29 C .634 16.10 .350 8.89 .634 16.10 .634 16.10 D Connector Part Numbers 2.375 60.33 4.375 111.13 6.125 155.58 Seating Tool Numbers** 650148-1 58084-1 650281-1* 650149-1 58084-3 650150-1 58084-2 * Contacts in this connector are underplated .000150 [0.00381] nickel. ** See page 149 for a description of AMP seating machines. Recommended PC Board Layout (Shown from post side) For mounting hole specifications, see page 123 Note: ACTION PIN posts require .093 [2.36] min. thick PC board. 117 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide breakthrough and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today's standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. Annular Ring (See Note) Drilled Hole Copper Thickness Tin-Lead Thickness Plated Through-Hole Mounting Hole Specifications ACTION PIN Contact Material Thickness Drilled Hole Diameter Copper* .025 0.64 .0453.001 1.1510.03 .001-.003 0.03-0.08 Plating Thicknesses Tin-Lead Plated-Through Hole Diameter Average Maximum .037-.043 0.94-1.09 .0015 0.038 .002 0.05 .0003 Min. 0.008 Radial Hole Distortion *Maximum hardness of copper layer is 150 Knoop Note: Recommended annular ring diameter is hole diameter plus .020 [0.51] 118 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors Performance Specifications Electrical Characteristics Contact Resistance: 8 milliohms (max.) Insulation Resistance: 2,000 megohms (min.) Continuous Current Rating*: 3 amperes Physical Characteristics Card Insertion Force: 16 oz [4.45 N] (max.) per contact pair Card Extraction Force: 1 oz [0.28 N] (min.) per contact pair Retention (in PC Board): 7 lb [31.1 N] (min.) Operating Temperature: -65C to +125C AMP ECONOMATE Connectors provide a reliable and economical method for interconnecting backplane panels, using either two-sided or multilayer PC boards. Connector housings are furnished unloaded and are available for post centerline spacings of: .100 x .200 [2.54 x 5.08] and .156 x .200 [3.96 x 5.08]. The housings are simply positioned onto the contacts, after the contacts have been inserted into the PC board and the carrier strip removed. Contacts from Tyco Electronics feature the proven and reliable ACTION PIN contact design.These press-fit contacts employ two spring members that compress to exert force against the plated through-holes for a gas-tight connection. Gold plating of contacts promotes the electrical integrity of the connection. Important: Application tooling is absolutely necessary for installing contacts and housings onto PC boards. See page 126 for application tooling. Feed-through posts are also available for accepting wrap-type terminations. These posts also feature the ACTION PIN contact design and are supplied in strip form and stored on reels for insertion into PC boards. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 119 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) .100 x .200 [2.54 x 5.08] Centerline Spacing B (Card Slot Length) A Material and Finish: Housing--Black glass-filled nylon Contacts--Copper alloy 725, plated as follows: Plating A--Selectively plated .000030 [0.00076] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating B--Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Plating C--Selectively plated .000100 [0.00254] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, except .000050 [0.00127] min. gold for .200 [5.08] from tip of post, with entire contact underplated .000050 [0.00127] min. nickel No. of Dual Positions .100 [2.54] 2.734 82.14 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 5.234 132.94 6.234 158.34 25 30 Accepts .054-.071 [1.37-1.80] PC Boards 35 36 40 50 60 2.604 78.84 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 5.104 129.64 6.104 155.04 1-117798-4 1-117798-3 1-117798-6 1-117798-7 1-117798-8 1-117798-1 1-117798-2 Note: Other connector sizes can be made available, consult Tyco Electronics. .415 [10.54] .181 [4.60] Related Product Data: Performance Specifications-- page 119 Card Guides--page 122 ACTION PIN Contact Mounting Hole Specifications--page 125 Application Tooling--page 126 Housing Part Numbers Dimensions A B Contact Area .545 [13.84] L .093-.125 [2.36-3.18] .200 [5.08] .025 Sq. [0.64] Technical Documents: (pages 186, 187): Product Specification 108-26002 .100 [2.54] Dimension L Keying Plugs .475 12.07 .702 17.83 Make-Before-Break Contacts Plating A Contact Part Numbers* Plating B Plating C 2-117795-4 4-117795-0 -- 1-117795-3 2-117795-6 4-117795-8 *Contacts are strip form, 35,000 per reel. Intercontact (Plastic) Part No. 118982-1 Dimension L .040 Ref. [1.02] Gold in Contact Area On-Contact (Plastic) Part No. 119802-2 .475 12.07 .702 17.83 Make Before Break Contact Part Numbers* Plating A Plating B -- 4-118951-8 1-118951-4 -- .025 Sq. [0.64] .100 [2.54] 120 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) 3.588 [91.14] (Card Slot Length) .156 x .200 [3.96 x 5.08] Centerline Spacing 3.718 [94.44] Material and Finish: Housing--Black glass-filled nylon Contacts--Copper alloy 725, plated as follows: Plating A--Selectively plated .000030 [0.00076] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating B--Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel .156 [3.96] Accepts .054-.071 [1.37-1.80] PC Boards .702 [17.83] .150 Ref. [3.01] Gold in Contact Area .025 Sq. [0.64] 22 Dual Position Housing Part No. 117296-4 .150 [3.06] Related Product Data: Make-Before-Break Contacts Performance Specifications-- page 119 Card Guides--page 122 ACTION PIN Contact Mounting Hole Specifications--page 125 Application Tooling--page 126 Technical Documents: (pages 186, 187): Product Specification 108-26002 .181 [4.60] .415 [10.54] .545 [13.84] Keying Plug Contact Area .093-.125 [2.36-3.18] L .200 [5.08] .025 Sq. [0.64] Note: Other connector sizes can be made available, consult Tyco Electronics. Intercontact (Plastic) Part No. 118982-1 .156 [3.96] Make Before Break Contacts Dimension Part Plating L Numbers* .475 B 1-118778-2 12.07 .702 A 118778-6 17.83 Dimension L .475 12.07 .702 17.83 Contact Part Numbers* 117285-7 117285-8 *Contacts are strip form, 15,000 per reel. 121 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Card Guides for ECONOMATE Connectors Material: Black glass-filled nylon Related Product Data: Mates with all .100 x .200 [2.54 x 5.08] and .156 x .200 [3.96 x 5.08] centerline housings Technical Documents: (pages 186, 187): Instruction Sheet 408-9091 Hole for No. 4 Screw 0.45 deep [11.43] L .220 [5.59] .410 [10.41] .152 Dia. [3.86] (2 Plcs.) A1 Recommended Mounting Dimensions Dimension L* 2.500 63.50 6.000 152.40 Card Guide Part Numbers 1-117169-3 1-117169-3 *Other lengths can be made available in .500 [12.70] increments from 1.500 [38.10] to 6.500 [165.10]. Consult Tyco Electronics for details. Housing Centerline No. of Dual Spacing Positions 30 35 .100 x .200 2.54 x 5.08 36 40 50 60 .156 x .200 3.96 x 5.08 22 Dimension A1 3.544 90.02 4.044 102.72 4.144 105.26 4.544 115.42 5.544 140.82 6.544 166.22 4.028 102.31 Note: A1 dimension = A dimension of ECONOMATE housing plus .310 [7.87]. 122 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Center Carrier Feed-Thru Posts* .100 [2.54] Centerline, Wrap Type Dimensions Material: Copper Alloy 725 Finish - Gold plate per MIL-G-45204 over nickel plate per QQ-N-290 (see table for thicknesses) Recommended Hole Size: Non-Plated-thru Hole - .0453.001 [1.150.03], 1.15 mm drill .004 0.1 Plated-thru Hole - .039 .003 [0.99 0.08], 1.15 mm drill Part Numbers 1) .000001 [0.00003] min. gold flash over .000050 [0.0013] min. nickel plate 2) .000050 [0.0013] min. gold plate over .000050 [0.0013] min. nickel plate A B C .318 8.08 .578 14.68 .578 14.68 .380 9.65 .687 17.45 .460 11.68 .550 13.97 .823 20.90 1.005 25.53 1.038 26.37 1.128 28.65 1.203 30.56 -- 118243-8 1-118243-1 -- .100 [2.54] Centerline, TERMI-POINT Clip Part Number 119136-2 Material: Copper Alloy 725 Finish - 1) Gold plate per MIL-G-45204, .000030 [0.00076] min. thk. over nickel plate per QQ-N-290, .000050 [0.0013] min. thk. 2) Gold flash per MIL-G-45204, .000001 [0.00003] min. thk. over nickel plate per QQ-N-290, .000050 [0.0013] min. thk. Recommended Hole Size: Non Plated-thru Hole - .0453.001 [1.150.03], 1.15 mm drill .004 0.1 Plated-thru Hole - .039.003 [0.99 0.08], 1.15 mm drill .125 [3.18] Centerline, Wrap Type Material: Copper Alloy 725 Finish - Gold plate per MIL-G-45204 or solder plate over nickel plate per QQ-N-290 (see table for thicknesses) Recommended Hole Size: - .0453.001 Non Plated-thru Hole [1.150.03], 1.15 mm drill .004 0.1 Plated-Thru Hole - .039 .003 [0.99 0.08], 1.15 mm drill Dimensions A B .703 17.68 .548 13.92 Part Numbers .000100 [0.0025] min. .000030 [0.00076] tin plate over gold plate over .000050 [0.0013] min. .000050 [0.0013] nickel plate nickel plate 117311-7 1-117311-0 *Use AMP Cut and Transfer Machine for center carrier post insertion. Consult Tyco Electronics. 123 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) Feed-Through Posts .100 [2.54] Centerline Spacing Material and Finish: Copper alloy 725, plated as follows: Plating A--Selectively plated .000030 [0.00076] min. gold in Area (1), .000001 [0.00003] min. gold in Area (2), with entire post underplated .000050 [0.00127] min. nickel Plating B--.000030 [0.00076] min. gold over .000100 [0.00254] min. nickel on entire post Plating C--.000050 [0.00127] min. gold over .000100 [0.00254] min. nickel on entire post Plating D--.000100 [0.00254] min. tin-lead over .000050 [0.00127] min. nickel on entire post .318 [8.08] (1) .045 [1.14] .030 [0.76] (2) A Pre-Notch .025 [0.64] .100 [2.54] Dimension A .687 17.45 .500 12.70 Plating A 1-117249-7 13-117249-11 3-117249-2 .025 [0.64] Feed-Through Post Part Numbers* Plating B Plating C Plating D 1-117249-2 1-117249-2 6-117249-5 -- -- 5-117249-6 *Posts in strip form, 50,000 per reel. 1Pre-notched to break with 120 bend. .150 [3.81] Centerline Spacing Material and Finish: Copper alloy 725, selectively plated .000030 [0.00076] min. gold in Area (1), .000001 [0.00003] min. gold in Area (2), with entire post underplated .000050 [0.00127] min. nickel .318 [8.08] (1) .045 [1.14] .030 [0.76] (2) .687 [17.45] .150 [3.81] .025 [0.64] .025 [0.64] 50,000 per reel Part No. 117269-5 124 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today's standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. Annular Ring (See Note) Drilled Hole Copper Thickness Tin-Lead Thickness Plated Through-Hole Mounting Hole Specifications Connector No. of Dual Centerline Positions .100 x .200 30, 35, 36, 2.54 x 5.08 40, 50, 60 .156 x .200 22 3.96 x 5.08 ACTION PIN Contact Material Thickness Drilled Hole Diameter .025 0.64 .0453.001 1.1510.03 Plating Thicknesses Copper* Tin-Lead .001-.003 0.03-0.08 .0003 0.008 Min. Plated Through-Hole Diameter .037-.043 0.94-1.09 Radial Hole Distortion Average Maximum Not Specified Not Specified *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 125 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Application Tooling for ECONOMATE Connectors Available from Tyco Electronics is a complete series of ACTION PIN Assembly Tooling Kits for ECONOMATE connector housings and feed-through posts. Assembly Kit tools provide the means for installing housings and contacts onto printed circuit boards, as well as removing housings and contacts from the printed circuit boards. All tools are available in kits, or may be purchased individually. In many instances, part number series are listed in the charts. Specific dash numbers and detailed information on the contacts and housings are presented on the respective product specification pages. For specific dash numbers and complete information on the tooling, contact Tyco Electronics. For ECONOMATE Connectors ACTION PIN Contacts Pin Length Part Numbers .125 x .125 3.18 x 3.18 .702 17.83 117793- 15-60 117796- .100 x .200 2.54 x 5.08 .702 17.83 117795- 15-60 117798- .156 x .200 3.96 x 5.08 .702 17.83 117285- 15-50 117296- .156 x .200 3.96 x 5.08 .475 12.07 117285- 15-50 117296- .100 x .200 2.54 x 5.08 .475 12.07 117795- 15-60 117798- .100 2.54 .340 8.64 117880- 20-60 117879- Centerline ECONOMATE Housings No. of Dual Part Positions Numbers ACTION PIN Assembly Tool Numbers Applicator 265902- Carrier Removal Tool 265924- Housing Assembly Tool 58292- Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265904- Carrier Removal Tool 265924- Housing Assembly Tool 265879- Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265905- Carrier Removal Tool 265924- Housing Assembly Tool 265881- Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265906- Carrier Removal Tool 265924- Housing Assembly Tool 265881- Housing Removal Tool 265868-1 Pin Replacement Tool 265871-3 Applicator 266129- Carrier Removal Tool 265924- Housing Assembly Tool 265879- Housing Removal Tool 265868-1 Pin Replacement Tool 265871-3 Applicator 265937- Carrier Removal Tool 265924- Housing Assembly Tool 265962- Housing Removal Tool 265868-2 Pin Replacement Tool 1-265871-1 For Feed-Through Posts ACTION PIN Contacts Pin No. of Length Positions Centerline Part Numbers .100 2.54 .500-.687 12.70-17.45 8-60 117249- .125 3.18 .687 17.45 8-60 117272- .150 3.81 .687 17.45 8-50 117269- .150 3.81 .365-.475 9.27-12.07 8-50 117269- Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. ACTION PIN Assembly Tool Numbers Applicator 265910- Carrier Removal Tool 265924- Pin Replacement Tool 265871-7 Applicator 265911- Carrier Removal Tool 265924- Pin Replacement Tool 265871-7 Applicator 265912- Carrier Removal Tool 265924- Pin Replacement Tool 265871-7 Applicator 265931- Carrier Removal Tool 265924- Pin Replacement Tool 265871-7 126 Catalog 1654080 Issued 7-03 www.tycoelectronics.com USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) High Density Press-Fit Card Edge Product Facts High density .050" [1.27] center spacing. Staggered contacts for low insertion force. Designed for multi-layer .093" [2.36] daughter cards. High temperature SMT solder reflow temperatures of 260 for 30 seconds. Unique pin geometry allows for even distribution of forces reducing axial pin rotation and preserving perpendicularity to the PCB board. Edge and side coining provides a uniform pin radius ensuring maximum contact without "skiving" the plated hole. Full complement of application tooling available. Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR 49571 (R) High Density (.050" [1.27] center spacing) Press-Fit connectors from Tyco Electronics are designed for high density backplane or mid-plane applications. Compliant pin connectors from Tyco Electronics meet or exceed requirements of current industry standards, including Bellcore specifications, which address critical performance issues such as hole retention, hole deformation and environmental performance. Electrical Characteristics: Operating Voltage-600VDC (sea level) Current Rating -1.5 Amperes Initial Contact Resistance - 30 milliohms Environmental Characteristics: Operating Temperature - -55C to +125C Temperature Cycling - MIL-STD-202 method 107 Vibration- MIL-STD-202, method 204 127 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) .050 [1.27] Centerline For .093 [2.36] Thick Daughter Cards Material and Finish: Insulation Resistance--1000 megohms minimum Contact Retention into PCB--2 lbs. min. Insertion Force--10 oz. max. Mating Force--2 oz. per contact Housing--High Temp. Glass filled thermoplastic, UL rating 94V-0 Color--Black Spring Contact--BeCu Contact Plating--Palladium Nickel +.005 .066 -.010 +.127 [1.68 -.254 ] X .610 [15.49] .461 .421 [11.71] [10.69] .016 [.41] .148 [3.76] .138 [3.51] X Section X-X "A" Spaces * .050 [1.27] = B D C (Card Slot) .132 [3.35] .400 [10.15] .332 [8.43] E Note: Dimension E is Connector Mounting PC Hole Pattern. 128 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Ordering Information No. of Dual Readout Position A 20 19 30 29 40 39 50 49 60 59 Dimensions B C D E F 0.950 [24.13] 1.450 [36.83] 1.950 [49.53] 2.450 [62.23] 2.950 [74.93] 1.040 [26.42] 1.540 [39.12] 2.040 [51.82] 2.540 [64.52] 3.040 [77.22] 1.230 [31.24] 1.730 [43.94] 2.230 [56.64] 2.730 [69.34] 3.230 [82.04] 1.100 [27.94] 1.600 [40.64] 2.100 [53.34] 2.600 [66.04] 3.100 [78.74] 1.010 [25.65] 1.510 [38.35] 2.010 [51.05] 2.510 [63.75] 3.010 [76.45] TYCO Part Number Acquired Part Number 147668-2 C9D020PF60048 147668-3 C9D030PF60048 147668-4 C9D040PF60048 147668-5 C9D050PF60048 147668-6 C9D060PF60048 E o .024.002 (.61.05) o .096 (2.44) .166 [4.22] .066 [1.68] .096 [2.44] .075 [1.90] "A" Spaces at .050 [1.27] = B Connector Mounting PC Hole Pattern F R .047 Typ. [1.19] .093 Thick PC Board [2.36] "A" Spaces * .050 [1.27] = B .030 [.76] Y .320 Min. [8.13] .585 [14.86] .150 [3.81] Y 45 x .025 [.64] All Around .035 [.89] Typ. .125 [3.17] Section Y-Y Daughter Board Configuration 129 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) .100 x .100 [2.54 x 2.54] Centerline Press Fit, with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum Contact Retention Into PCB-- 5lbs. min. [356 N] Insertion Force--10 oz. [44.5 N] max. measured with a .0700 .0001 [1.80.00254] THK polished blade per MIL-C-21097C Withdrawal Force--1 oz. min. [4.54 N] measured with a .0540 .0001 [3.37.000254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 .0001 [1.80.00254] THK blade Insulator Body--High Temp. Glass filled thermoplastic, UL rating 94V-O Color--Black Spring Contact--Phosphor Bronze alloy Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .100 [2.54] A B C .020 [.51] Contact Gap .365 [9.27] Ref. .100 [2.54] Electrical Properties: .550 [13.97] Operating Voltage--600 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms J Environmental Properties: .100 [2.54] Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration--MIL-STD-202, method 204 .025 Sq. Typ. [.64] C .040.003 [1.02.08] Dia. Dim C Application Tooling: Insertion Tool--page 150 Related Product Data: Daughter Card Edge Pattern-- page 57 .100 [2.54] .100 [2.54] 130 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Ordering Information .100 [2.54] Centerline/.100 [2.54] Row-To-Row with Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 C1D18PF29013 C1D18PF29133 C1D18PF29043 C1D20PF29013 C1D20PF29133 C1D20PF29043 C1D22PF29013 C1D22PF29133 C1D22PF29043 C1D25PF29013 C1D25PF29133 C1D25PF29043 C1D28PF29013 C1D28PF29133 C1D28PF29043 C1D30PF29013 C1D30PF29133 C1D30PF29043 C1D35PF29013 C1D35PF29133 C1D35PF29043 C1D36PF29013 C1D36PF29133 C1D36PF29043 C1D40PF29013 C1D40PF29133 C1D40PF29043 C1D43PF29013 C1D43PF29133 C1D43PF29043 C1D45PF29013 C1D45PF29133 C1D45PF29043 C1D50PF29013 C1D50PF29133 C1D50PF29043 C1D60PF29013 C1D60PF29133 C1D60PF29043 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 C1D18PF29015 C1D18PF29135 C1D18PF29045 C1D20PF29015 C1D20PF29135 C1D20PF29045 C1D22PF29015 C1D22PF29135 C1D22PF29045 C1D25PF29015 C1D25PF29135 C1D25PF29045 C1D28PF29015 C1D28PF29135 C1D28PF29045 C1D30PF29015 C1D30PF29135 C1D30PF29045 C1D35PF29015 C1D35PF29135 C1D35PF29045 C1D36PF29015 C1D36PF29135 C1D36PF29045 C1D40PF29015 C1D40PF29135 C1D40PF29045 C1D43PF29015 C1D43PF29135 C1D43PF29045 C1D45PF29015 C1D45PF29135 C1D45PF29045 C1D50PF29015 C1D50PF29135 C1D50PF29045 C1D60PF29015 C1D60PF29135 C1D60PF29045 Tail Length .180 [4.57] (Dim. "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 Tail Length .475 [12.07] (Dim. "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 131 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100" [2.54] Centerline / .100" [2.54] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth Tail Length .625 [15.88] (Dim. "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 C1D18PF29017 C1D18PF29137 C1D18PF29047 C1D20PF29017 C1D20PF29137 C1D20PF29047 C1D22PF29017 C1D22PF29137 C1D22PF29047 C1D25PF29017 C1D25PF29137 C1D25PF29047 C1D28PF29017 C1D28PF29137 C1D28PF29047 C1D30PF29017 C1D30PF29137 C1D30PF29047 C1D35PF29017 C1D35PF29137 C1D35PF29047 C1D36PF29017 C1D36PF29137 C1D36PF29047 C1D40PF29017 C1D40PF29137 C1D40PF29047 C1D43PF29017 C1D43PF29137 C1D43PF29047 C1D45PF29017 C1D45PF29137 C1D45PF29047 C1D50PF29017 C1D50PF29137 C1D50PF29047 C1D60PF29017 C1D60PF29137 C1D60PF29047 132 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline Press-Fit, Full Scoop Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 .21 Point of Contact [5.33] .395/.510 Card Slot Depth [10.03/12.95] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB-- 5lbs. min. [356 N] Insertion Force--10 oz. [44.5 N] max. measured with a .0700 .0001 [1.80.00254] THK polished blade per MIL-C-21097C Withdrawal Force--1 oz. min. [4.5 N] measured with a .0540 .0001 [3.37.00254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 .0001 [1.80.00254] THK blade Insulator Body--High Temp. Glass filled thermoplastic, UL rating 94V-O Color--Black Spring Contact--Phosphor Bronze alloy Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] B C .020.010 [.51.25] Contact Gap .390 [9.91] .100 [2.54] B .395/.510 Card Slot Depth [10.03/12.95] .645 Ref. [16.38] Electrical Properties Operating Voltage--600 VDC (sea level) Current Rating--3 Amperes Contact Resistance--10 milliohms J A Environmental Properties: C Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 Dim E .040.003 [1.02.08] Dia. Application Tooling: Insertion Tool--page 150 .200 [5.08] Related Product Data: Daughter Card Edge Pattern-- page 57 .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 133 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth Tail Length .670 [17.02] (DIM "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18PF29012 W8D18PF29042 W8D20PF29012 W8D20PF29042 W8D22PF29012 W8D22PF29042 W8D25PF29012 W8D25PF29042 W8D28PF29012 W8D28PF29042 W8D30PF29012 W8D30PF29042 W8D35PF29012 W8D35PF29042 W8D36PF29012 W8D36PF29042 W8D40PF29012 W8D40PF29042 W8D43PF29012 W8D43PF29042 W8D45PF29012 W8D45PF29042 W8D50PF29012 W8D50PF29042 W8D60PF29012 W8D60PF29042 W8D18PF29013 W8D18PF29043 W8D20PF29013 W8D20PF29043 W8D22PF29013 W8D22PF29043 W8D25PF29013 W8D25PF29043 W8D28PF29013 W8D28PF29043 W8D30PF29013 W8D30PF29043 W8D35PF29013 W8D35PF29043 W8D36PF29013 W8D36PF29043 W8D40PF29013 W8D40PF29043 W8D43PF29013 W8D43PF29043 W8D45PF29013 W8D45PF29043 W8D50PF29013 W8D50PF29043 W8D60PF29013 W8D60PF29043 Tail Length .180 [4.57] (DIM "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 134 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit, Full Scoop with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 .21 Point of Contact [5.33] .395/.510 Card Slot Depth [10.03/12.95] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB-- 5lbs. min. [356 N] Insertion Force--10 oz. [44.5 N] max. measured with a .0700 .0001 [1.80.00254] THK polished blade per MIL-C-21097C Withdrawal Force--1 oz. min. [4.5 N] measured with a .0540 .0001 [3.37.00254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 .0001 [1.80.00254] THK blade Insulator Body--High Temp. Glass filled thermoplastic, UL rating 94V-O Color--Black Spring Contact--Phosphor Bronze alloy Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] B C .020.010 [.51.25 ] Contact Gap .390 [9.91] .100 [2.54] B .395/.510 Card Slot Depth [10.03/12.95] .705 Ref. [17.91] Electrical Properties: Operating Voltage--600 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms J C A Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 Dim C .040.003 [1.02.08] Dia. Application Tooling: Insertion Tool--page 150 Related Product Data: .200 [5.08] Daughter Card Edge Pattern-- page 57 .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 135 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop with Standoffs Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth Tail Length .670 [17.02] (DIM "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18PF29062 W8D18PF29092 W8D20PF29062 W8D20PF29092 W8D22PF29062 W8D22PF29092 W8D25PF29062 W8D25PF29092 W8D28PF29062 W8D28PF29092 W8D30PF29062 W8D30PF29092 W8D35PF29062 W8D35PF29092 W8D36PF29062 W8D36PF29092 W8D40PF29062 W8D40PF29092 W8D43PF29062 W8D43PF29092 W8D45PF29062 W8D45PF29092 W8D50PF29062 W8D50PF29092 W8D60PF29062 W8D60PF29092 W8D18PF29063 W8D18PF29093 W8D20PF29063 W8D20PF29093 W8D22PF29063 W8D22PF29093 W8D25PF29063 W8D25PF29093 W8D28PF29063 W8D28PF29093 W8D30PF29063 W8D30PF29093 W8D35PF29063 W8D35PF29093 W8D36PF29063 W8D36PF29093 W8D40PF29063 W8D40PF29093 W8D43PF29063 W8D43PF29093 W8D45PF29063 W8D45PF29093 W8D50PF29063 W8D50PF29093 W8D60PF29063 W8D60PF29093 Tail Length .180 [4.57] (DIM "J") 18 20 22 25 28 30 35 36 40 43 45 50 60 136 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB--5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage--600 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 .100 [2.54] .550 [13.97] J Application Tooling: .100 [2.54] Insertion Tool--page 150 .025 Sq. Typ. [.64] C Related Product Data: Daughter Card Edge Pattern-- page 57 .040.003 [1.02.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .100 [2.54] 137 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row without Standoffs No. of Dual Readout Positions Dimensions A B C .300 [7.62] Card Slot Depth Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 C8D06PF29032 C8D06PF29142 C8D06PF29022 C8D10PF29032 C8D10PF29142 C8D10PF29022 C8D12PF29032 C8D12PF29142 C8D12PF29022 C8D15PF29032 C8D15PF29142 C8D15PF29022 C8D20PF29032 C8D20PF29142 C8D20PF29022 C8D22PF29032 C8D22PF29142 C8D22PF29022 C8D25PF29032 C8D25PF29142 C8D25PF29022 C8D28PF29032 C8D28PF29142 C8D28PF29022 C8D30PF29032 C8D30PF29142 C8D30PF29022 C8D31PF29032 C8D31PF29142 C8D31PF29022 C8D35PF29032 C8D35PF29142 C8D35PF29022 C8D36PF29032 C8D36PF29142 C8D36PF29022 C8D40PF29032 C8D40PF29142 C8D40PF29022 C8D43PF29032 C8D43PF29142 C8D43PF29022 C8D50PF29032 C8D50PF29142 C8D50PF29022 C8D60PF29032 C8D60PF29142 C8D60PF29022 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 C8D06PF29033 C8D06PF29143 C8D06PF29023 C8D10PF29033 C8D10PF29143 C8D10PF29023 C8D12PF29033 C8D12PF29143 C8D12PF29023 C8D15PF29033 C8D15PF29143 C8D15PF29023 C8D20PF29033 C8D20PF29143 C8D20PF29023 C8D22PF29033 C8D22PF29143 C8D22PF29023 C8D25PF29033 C8D25PF29143 C8D25PF29023 C8D28PF29033 C8D28PF29143 C8D28PF29023 C8D30PF29033 C8D30PF29143 C8D30PF29023 C8D31PF29033 C8D31PF29143 C8D31PF29023 C8D35PF29033 C8D35PF29143 C8D35PF29023 C8D36PF29033 C8D36PF29143 C8D36PF29023 C8D40PF29033 C8D40PF29143 C8D40PF29023 C8D43PF29033 C8D43PF29143 C8D43PF29023 C8D50PF29033 C8D50PF29143 C8D50PF29023 C8D60PF29033 C8D60PF29143 C8D60PF29023 Tail Length .670 [17.02] ("J") 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 Tail Length .180 [4.57] ("J") 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 138 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB--5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. .100 [2.54] Electrical Properties: Operating Voltage--600 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms .610 [15.49] Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 J .100 [2.54] .025 Sq. [.64] C Application Tooling: Insertion Tool--page 150 .040.003 [1.02.08] Dia. Related Product Data: Dim C Daughter Card Edge Pattern-- page 57 .200 [5.08] .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 139 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Center-to-Center/.200 [5.08] Row-To-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth Tail Length .670 [17.02] (dim "J") 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 C8D06PF29012 C8D06PF29132 C8D06PF29042 C8D10PF29012 C8D10PF29132 C8D10PF29042 C8D12PF29012 C8D12PF29132 C8D12PF29042 C8D15PF29012 C8D15PF29132 C8D15PF29042 C8D20PF29012 C8D20PF29132 C8D20PF29042 C8D22PF29012 C8D22PF29132 C8D22PF29042 C8D25PF29012 C8D25PF29132 C8D25PF29042 C8D28PF29012 C8D28PF29132 C8D28PF29042 C8D30PF29012 C8D30PF29132 C8D30PF29042 C8D31PF29012 C8D31PF29132 C8D31PF29042 C8D35PF29012 C8D35PF29132 C8D35PF29042 C8D36PF29012 C8D36PF29132 C8D36PF29042 C8D40PF29012 C8D40PF29132 C8D40PF29042 C8D43PF29012 C8D43PF29132 C8D43PF29042 C8D50PF29012 C8D50PF29132 C8D50PF29042 C8D60PF29012 C8D60PF29132 C8D60PF29042 C8D06PF29013 C8D06PF29133 C8D06PF29043 C8D10PF29013 C8D10PF29133 C8D10PF29043 C8D12PF29013 C8D12PF29133 C8D12PF29043 C8D15PF29013 C8D15PF29133 C8D15PF29043 C8D20PF29013 C8D20PF29133 C8D20PF29043 C8D22PF29013 C8D22PF29133 C8D22PF29043 C8D25PF29013 C8D25PF29133 C8D25PF29043 C8D28PF29013 C8D28PF29133 C8D28PF29043 C8D30PF29013 C8D30PF29133 C8D30PF29043 C8D31PF29013 C8D31PF29133 C8D31PF29043 C8D35PF29013 C8D35PF29133 C8D35PF29043 C8D36PF29013 C8D36PF29133 C8D36PF29043 C8D40PF29013 C8D40PF29133 C8D40PF29043 C8D43PF29013 C8D43PF29133 C8D43PF29043 C8D50PF29013 C8D50PF29133 C8D50PF29043 C8D60PF29013 C8D60PF29133 C8D60PF29043 Tail Length .180 [4.57] (dim "J") 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 140 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .125 x .250 [3.18 x 6.35] Centerline without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB--5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .250 [6.35] A B C Electrical Properties: Operating Voltage--1000 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms .020 [.51] Contact Gap .365 [9.27] .125 [3.18] .550 [13.97] Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 J .125 [3.18] Application Tooling: .025 Sq. Typ. [.64] C Insertion Tool--page 150 Related Product Data: Daughter Card Edge Pattern-- page 57 .040.003 [1.02.08] Dia. Dim C .250 [6.35] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .125 [3.18] 141 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .125 [3.18] Centerline /.250 [6.35] Row-to-Row without Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29032 C7D06PF29142 C7D06PF29022 C7D10PF29032 C7D10PF29142 C7D10PF29022 C7D12PF29032 C7D12PF29142 C7D12PF29022 C7D15PF29032 C7D15PF29142 C7D15PF29022 C7D18PF29032 C7D18PF29142 C7D18PF29022 C7D20PF29032 C7D20PF29142 C7D20PF29022 C7D22PF29032 C7D22PF29142 C7D22PF29022 C7D25PF29032 C7D25PF29142 C7D25PF29022 C7D28PF29032 C7D28PF29142 C7D28PF29022 C7D30PF29032 C7D30PF29142 C7D30PF29022 C7D31PF29032 C7D31PF29142 C7D31PF29022 C7D35PF29032 C7D35PF29142 C7D35PF29022 C7D36PF29032 C7D36PF29142 C7D36PF29022 C7D40PF29032 C7D40PF29142 C7D40PF29022 C7D43PF29032 C7D43PF29142 C7D43PF29022 C7D50PF29032 C7D50PF29142 C7D50PF29022 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29033 C7D06PF29143 C7D06PF29023 C7D10PF29033 C7D10PF29143 C7D10PF29023 C7D12PF29033 C7D12PF29143 C7D12PF29023 C7D15PF29033 C7D15PF29143 C7D15PF29023 C7D18PF29033 C7D18PF29143 C7D18PF29023 C7D20PF29033 C7D20PF29143 C7D20PF29023 C7D22PF29033 C7D22PF29143 C7D22PF29023 C7D25PF29033 C7D25PF29143 C7D25PF29023 C7D28PF29033 C7D28PF29143 C7D28PF29023 C7D30PF29033 C7D30PF29143 C7D30PF29023 C7D31PF29033 C7D31PF29143 C7D31PF29023 C7D35PF29033 C7D35PF29143 C7D35PF29023 C7D36PF29033 C7D36PF29143 C7D36PF29023 C7D40PF29033 C7D40PF29143 C7D40PF29023 C7D43PF29033 C7D43PF29143 C7D43PF29023 C7D50PF29033 C7D50PF29143 C7D50PF29023 Tail Length .670 [17.02] (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 Tail Length .180 [4.57] (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 142 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .125 x .250 [3.18 x 6.35] Centerline with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB--5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] .125 [3.18] Electrical Properties: Operating Voltage--1000 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms .550 [13.97] Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 J .125 [3.18] Application Tooling: .025 Sq. Typ. [.64] C Insertion Tool--page 150 Related Product Data: .040.003 [1.02.08] Dia. Daughter Card Edge Pattern-- page 57 Dim C .250 [6.35] .125 [3.18] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 143 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .125 [3.18] Centerline /.250 [6.35] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29012 C7D06PF29132 C7D06PF29042 C7D10PF29012 C7D10PF29132 C7D10PF29042 C7D12PF29012 C7D12PF29132 C7D12PF29042 C7D15PF29012 C7D15PF29132 C7D15PF29042 C7D18PF29012 C7D18PF29132 C7D18PF29042 C7D20PF29012 C7D20PF29132 C7D20PF29042 C7D22PF29012 C7D22PF29132 C7D22PF29042 C7D25PF29012 C7D25PF29132 C7D25PF29042 C7D28PF29012 C7D28PF29132 C7D28PF29042 C7D30PF29012 C7D30PF29132 C7D30PF29042 C7D31PF29012 C7D31PF29132 C7D31PF29042 C7D35PF29012 C7D35PF29132 C7D35PF29042 C7D36PF29012 C7D36PF29132 C7D36PF29042 C7D40PF29012 C7D40PF29132 C7D40PF29042 C7D43PF29012 C7D43PF29132 C7D43PF29042 C7D50PF29012 C7D50PF29132 C7D50PF29042 C7D06PF29013 C7D06PF29133 C7D06PF29043 C7D10PF29013 C7D10PF29133 C7D10PF29043 C7D12PF29013 C7D12PF29133 C7D12PF29043 C7D15PF29013 C7D15PF29133 C7D15PF29043 C7D18PF29013 C7D18PF29133 C7D18PF29043 C7D20PF29013 C7D20PF29133 C7D20PF29043 C7D22PF29013 C7D22PF29133 C7D22PF29043 C7D25PF29013 C7D25PF29133 C7D25PF29043 C7D28PF29013 C7D28PF29133 C7D28PF29043 C7D30PF29013 C7D30PF29133 C7D30PF29043 C7D31PF29013 C7D31PF29133 C7D31PF29043 C7D35PF29013 C7D35PF29133 C7D35PF29043 C7D36PF29013 C7D36PF29133 C7D36PF29043 C7D40PF29013 C7D40PF29133 C7D40PF29043 C7D43PF29013 C7D43PF29133 C7D43PF29043 C7D50PF29013 C7D50PF29133 C7D50PF29043 Tail Length .670 [17.02] (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 Tail Length .180 [4.57] (DIM "J") 1.035 0.875 26.29 22.23 1.535 1.375 10 38.99 34.93 1.785 1.625 12 45.34 41.28 2.160 2.000 15 54.86 50.80 2.535 2.375 18 64.39 60.33 2.785 2.625 20 70.74 66.68 3.035 2.875 22 77.09 73.03 3.410 3.250 25 86.61 82.55 3.785 3.625 28 96.14 92.08 4.035 3.875 30 102.49 98.43 4.160 4.000 31 105.66 101.60 4.660 4.500 35 118.36 114.30 4.785 4.625 36 121.54 117.48 5.285 5.125 40 134.24 130.18 5.660 5.500 43 143.76 139.70 6.535 6.375 50 165.99 161.93 NOTE: Optional stacking designs are available (consult Tyco Electronics). 6 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 144 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .156 x .200 [3.18 x 5.08] Centerline without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120.003 [3.05.25] Point of Contact Card Slot .300 [7.62] Depth .350 [8.89] .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB-- 5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage--1500 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms Environmental Properties: Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 .156 [3.96] .550 [13.97] J Application Tooling: .156 [3.96] .025 Sq. Typ. [.64] Insertion Tool--page 150 C Related Product Data: Daughter Card Edge Pattern-- page 57 .040.003 [1.02.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .156 [3.96] 145 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .156 [3.18] Centerline/.200 [5.08] Row-to-Row without Standoffs Dimensions No. of Dual Readout Positions A B C .300 [7.62] Card Slot Depth Acquired Part Numbers .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 C6D06PF29032 C6D06PF29142 C6D06PF29022 C6D10PF29032 C6D10PF29142 C6D10PF29022 C6D12PF29032 C6D12PF29142 C6D12PF29022 C6D15PF29032 C6D15PF29142 C6D15PF29022 C6D18PF29032 C6D18PF29142 C6D18PF29022 C6D20PF29032 C6D20PF29142 C6D20PF29022 C6D22PF29032 C6D22PF29142 C6D22PF29022 C6D25PF29032 C6D25PF29142 C6D25PF29022 C6D28PF29032 C6D28PF29142 C6D28PF29022 C6D30PF29032 C6D30PF29142 C6D30PF29022 C6D31PF29032 C6D31PF29142 C6D31PF29022 C6D35PF29032 C6D35PF29142 C6D35PF29022 C6D36PF29032 C6D36PF29142 C6D36PF29022 C6D40PF29032 C6D40PF29142 C6D40PF29022 C6D43PF29032 C6D43PF29142 C6D43PF29022 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 C6D06PF29033 C6D06PF29143 C6D06PF29023 C6D10PF29033 C6D10PF29143 C6D10PF29023 C6D12PF29033 C6D12PF29143 C6D12PF29023 C6D15PF29033 C6D15PF29143 C6D15PF29023 C6D18PF29033 C6D18PF29143 C6D18PF29023 C6D20PF29033 C6D20PF29143 C6D20PF29023 C6D22PF29033 C6D22PF29143 C6D22PF29023 C6D25PF29033 C6D25PF29143 C6D25PF29023 C6D28PF29033 C6D28PF29143 C6D28PF29023 C6D30PF29033 C6D30PF29143 C6D30PF29023 C6D31PF29033 C6D31PF29143 C6D31PF29023 C6D35PF29033 C6D35PF29143 C6D35PF29023 C6D36PF29033 C6D36PF29143 C6D36PF29023 C6D40PF29033 C6D40PF29143 C6D40PF29023 C6D43PF29033 C6D43PF29143 C6D43PF29023 .670 [17.02] Tail Length (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 .180 [4.57] Tail Length (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 146 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .156 x .200 [3.18 x 5.08] Centerline with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards Association, File No. LR49571 Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120.003 [3.05.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance-- 5000 megohms minimum. Contact Retention Into PCB--5 lbs. [356 N] Insertion/Withdrawal Force-- 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body--Glass filled thermoplastic, UL rating 94V-O Color--Black Contacts--High strength copper alloy. Contact Plating--.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage--1500 VDC (sea level) Current Rating--3 Amperes Initial Contact Resistance-- 10 milliohms .156 [3.96] Environmental Properties: .610 [15.49] Operating Temperature-- -55C to +125C Temperature Cycling-- MIL-STD-202 method 107 Vibration-- MIL-STD-202, method 204 J .156 [3.96] Application Tooling: Insertion Tool--page 150 .025 Sq. Typ. [.64] C Related Product Data: Daughter Card Edge Pattern-- page 57 .040.003 [1.02.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .156 [3.96] 147 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .156 [3.18] Centerline/.200 [5.08] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth .670 [17.02] Tail Length (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 C6D06PF29012 C6D06PF29132 C6D06PF29042 C6D10PF29012 C6D10PF29132 C6D10PF29042 C6D12PF29012 C6D12PF29132 C6D12PF29042 C6D15PF29012 C6D15PF29132 C6D15PF29042 C6D18PF29012 C6D18PF29132 C6D18PF29042 C6D20PF29012 C6D20PF29132 C6D20PF29042 C6D22PF29012 C6D22PF29132 C6D22PF29042 C6D25PF29012 C6D25PF29132 C6D25PF29042 C6D28PF29012 C6D28PF29132 C6D28PF29042 C6D30PF29012 C6D30PF29132 C6D30PF29042 C6D31PF29012 C6D31PF29132 C6D31PF29042 C6D35PF29012 C6D35PF29132 C6D35PF29042 C6D36PF29012 C6D36PF29132 C6D36PF29042 C6D40PF29012 C6D40PF29132 C6D40PF29042 C6D43PF29012 C6D43PF29132 C6D43PF29042 C6D06PF29013 C6D06PF29133 C6D06PF29043 C6D10PF29013 C6D10PF29133 C6D10PF29043 C6D12PF29013 C6D12PF29133 C6D12PF29043 C6D15PF29013 C6D15PF29133 C6D15PF29043 C6D18PF29013 C6D18PF29133 C6D18PF29043 C6D20PF29013 C6D20PF29133 C6D20PF29043 C6D22PF29013 C6D22PF29133 C6D22PF29043 C6D25PF29013 C6D25PF29133 C6D25PF29043 C6D28PF29013 C6D28PF29133 C6D28PF29043 C6D30PF29013 C6D30PF29133 C6D30PF29043 C6D31PF29013 C6D31PF29133 C6D31PF29043 C6D35PF29013 C6D35PF29133 C6D35PF29043 C6D36PF29013 C6D36PF29133 C6D36PF29043 C6D40PF29013 C6D40PF29133 C6D40PF29043 C6D43PF29013 C6D43PF29133 C6D43PF29043 .180 [4.57] Tail Length (DIM "J") 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 148 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Application Tooling Tyco Electronics offers a complete line of servo-electric driven presses for the application of press-fit connectors. Each system features a PC controlled servo electric drive for precise application and monitoring of force, speed, and press height. The entire process is data driven to provide flexible programming and automatic set-up. SPC analysis is provided for each connector pressed to assure the quality of every application. BMEP 1K/2K Servo Electric Press * 1000 or 2000 lb force [4.5 or 9 kN] * 12" [305 mm] throat depth * Compact footprint - 16" x 24" [406 x 610 mm] * Force resolution of approximately 1 lb [4.4 N] for delicate press applications. BMEP 3T/5T Benchtop Electric Servo Press * 3 or 5 tons force [27 or 44 kN] * 18" x 24" [460 x 610 mm] PCB capacity * Compact footprint - 24" x 48" [610 x 1220 mm] * Midrange force and board size capacity in a benchtop unit. MEP 6T/12 T Manual Electric Servo Press * 6 or 12 tons force [53 or 107 kN] * 24" x 36" [610 x 914 mm] PCB capacity * Self-contained, portable unit * Compact, manual unit capable of handling large boards and high force applications. Automatic Pick, Place and Press (AP3) * 8 tons force [71 kN] * 18" x 30" [457 x 762 mm] PCB capacity * SMEMA compatible unit for automatic pick, place and press of connectors and odd-from components. * Vision system for pin inspection prior to placement. 149 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Card Edge Insertion Tools Ordering Information Tool Part Number Acquired P/N TYCO Replacement Blade Part Number Acquired P/N Tyco Center-to Center Connector Prefix Max. No. Of Positions .100 x .100 2.54 x 2.54 .100 x .100 2.54 x 2.54 .156 x .200 3.96 x 5.08 .125 x .250 3.18 x 6.35 .100 x .200 2.54 x 5.08 .100 x .200 2.54 x 5.08 (Full Scoop) .100 x .200 2.54 x 5.08 (Full Scoop) C1 70 98336 3-1437266-5 98293 1437274-1 C1 100 98341 -- 98293 1437274-1 C6 43 98231 1-1437266-1 98206 1437266-8 C7 50 98230 1-1437266-0 98206 1437266-8 C8 70 98224 1-1437266-9 98206 1437266-8 W8 70 98236 1-1490560-1 98238 1490563-1 W8 35 98236 1-1490560-2 98238 1490563-1 150 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Card Edge Removal Tool Kits Description Removal tool kits include: impact tools, removal tips for tail lengths ranging from .180 in. [4.57] to .680 in. [17.27] Kits for .100" x .200" [2.54 x 5.08] Series Card Edge connectors include the insertion tip. Ordering Information Center x Row .156 x .200 3.96 x 5.08 .125 x .250 3.18 x 6.35 .100 x .200 2.54 x 5.08 .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 Wide Full Scoop Prefix Acquired Kit Number Tyco Kit Number C6 9818002 1437266-3 C7 9818002 1437266-3 C8 9818002 1437266-3 C1 9818004 1437266-4 W8 9818005 1437266-5 Ordering Information Item No. 1 2 3 4 6 10 11 12 Description Impact Tool Removal Tip - .180 [4.57] Tail Removal Tip - .378/.475 Tail 9.60/12.07 Removal Tip - .670/.680 Tail 17.02/17.27 Insertion Tip - C6, 7 & 8 PF Removal Tip - .550/.625 Tail 13.97/15.88 Insertion Tip - C1 Series PF Insertion Tip - W8 Series PF 9818001 Applies to Kit No. 9818001 9818003 9818004 Replacement Tyco Part Part 9818005 Number Number 9820401 9820301 1437266-7 1437266-6 9820302 1437260-4 9820303 -- 9836701 3-1437266-9 9820305 1437260-5 9836301 9836702 1437260-6 1437260-7 151 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967