LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 LM49352 BoomerTM Mono Class D Audio Codec Subsystem with Ground Referenced Headphone Amplifiers, Earpiece Driver, and Audio DSP Check for Samples: LM49352 FEATURES 1 * 23 * * * * * * * * * * * * * * * * * * * * * Ultra Efficient, Spread Spectrum Class D Loudspeaker Amplifier that Operates at 93% Efficiency Low Voltage, True Ground Headphone Amplifier Operation High Performance 103dB SNR Stereo DAC High Performance 97dB SNR Stereo ADC Up to 96kHz Stereo Audio Playback Up to 48kHz Stereo Recording Dual Bidirectional I2S or PCM Compatible Audio Interfaces Read/Write I2C Compatible Control Interface Flexible Digital Mixer with Sample Rate Conversion Sigma-Delta PLL Clock Network that Supports System Clocks up to 50MHz Including 13MHz, 19.2MHz, and 26MHz Dual stereo 5 band parametric equalizers Cascadable DSP Effects that Allow Stereo 10 Band Parametric Equalization ALC/Limiter/Compressor on Both DAC and ADC Paths Dedicated Earpiece Speaker Amplifier Stereo Auxiliary Inputs and Mono Differential Input Differential Microphone Input with SingleEnded Option Automatic Level Control for Digital Audio Inputs, Mono Differential Input, Microphone Input, and Stereo Auxiliary Inputs Flexible Audio Routing from Input to Output 16 Step Volume Control for Microphone with 2dB Steps 32 Step Volume Control for Auxiliary Inputs in 1.5dB Steps 4 Step Volume Control for Class D Loudspeaker Amplifier 8 Step Volume Control for Headphone Amplifier * * Micro-Power Shutdown Mode Available in the 3.3 x 3.3 mm 36 bump DSBGA package APPLICATIONS * * * * * Smart Phones Mobile Phones and VOIP Phones Portable GPS Navigator and Portable Gaming Devices Portable DVD/CD/AAC/MP3/MP4 Players Digital Cameras/Camcorders KEY SPECIFICATIONS * * * * * * * * Class D Amplifier Efficiency 93% (Typ) PEP at A_VDD = 3.3V, 32, 1% THD 58mW (Typ) PHP at HP_VDD = 2.8V, Stereo 32, 1% THD 65mW/ch (Typ) PLS at LS_VDD = 5V, 8, 1% THD 1.4W (Typ) PLS at LS_VDD = 4.2V, 8, 1% THD 970 mW (Typ) PLS at LS_VDD = 3.3V, 8, 1% THD 590 mW (Typ) SNR (Stereo DAC at 48kHz) 103 dB (Typ) PSRR at 217 Hz, A_VDD = 3.3V, (HP from AUX) 100dB (Typ) DESCRIPTION The LM49352 is a high performance mixed signal audio subsystem. The LM49352 includes a high quality stereo DAC, a high quality stereo ADC, a stereo headphone amplifier, which supports True Ground operation, a low EMI Class D loudspeaker amplifier, and an earpiece speaker amplifier. It combines advanced audio processing, conversion, mixing, and amplification in the smallest possible footprint while extending the battery life of feature rich portable devices. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Boomer is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2009-2013, Texas Instruments Incorporated LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com DESCRIPTION (CONTINUED) The LM49352 features dual bi-directional I2S or PCM audio interfaces and an I2C compatible interface for control. The stereo DAC path features an SNR of 103dB with 24-bit 48 kHz input. The headphone amplifier delivers 65mWRMS (typ) to a 32 single-ended stereo load with less than 1% distortion (THD+N) when HP_VDD = 2.8V. The loudspeaker amplifier delivers up to 970mW into an 8 load with less than 1% distortion when LS_VDD = 4.2V. The LM49352 employs advanced techniques to extend battery life, to reduce controller overhead, to speed development time, and to eliminate click and pop artifacts. Boomer audio power amplifiers are designed specifically for mobile devices and require minimal PCB area and external components. LM49352 Overview I/O_VDD D_VDD DGND ADCREF A_VDD AGND LS_VDD LSGND HP_VDD EP+/ AUX_OUT+ SCL SDA 0 dB to 6 dB 2 I C SLAVE REGISTERS PORT1_CLK ADC EFFECTS PORT1_SDI PORT1_SDO PORT2_CLK PORT2_WS PORT2_SDI DIGITAL MIXER & AUDIO PORTS PORT1_WS PORT2_SDO/GPIO EP-/ AUX_OUT- POWER MANAGEMENT and CONTROL VOL CTRL 5-BAND EQ ALC DAC_LEFT CLOCK NETWORK with 6' PLL VOL CTRL 5-BAND EQ ALC LS_OUT- 0 dB to 12 dB 6' LEFT ADC CP+ CP- CHARGE PUMP HPVSS 6' RIGHT ADC HP_VDD -18 dB to 0 dB DAC EFFECTS LS_OUT+ D DAC_RIGHT MONO AUX MIC MCLK AB 6' LEFT DAC AB HPL_OUT HP_VSS HP_VDD 6' RIGHT DAC -18 dB to 0 dB MONO_IN+ AB HPR_OUT HP_VSS MONO_INVCM -46.5 dB to 18 dB VCM DACREF BG AUXL / AUX- VCM AUXR / AUX+ 6 dB to 36 dB MIC+ MIC- Figure 1. LM49352 Block Diagram 2 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Application D_VDD I/O_VDD ADC REF HP_VSS A_VDD LS_VDD HP_VDD MIC+ DACREF MIC- CP+ CP0.5 - 50 MHz MCLK HPL 2 I C HPR Baseband Controller 2 I S / PCM (PORT1) LM49352 LS+ LS- MONO+ 8O MONOEP+ EPMultimedia IC 32O 2 I S / PCM (PORT2) DGND LSGND AGND AUX_L AUX_R Synthesized FM Radio / TV Tuner Figure 2. Example Application in Multimedia Phone with Dedicated Earpiece Speaker and Mono Loudspeaker Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 3 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com D_VDD I/O_VDD ADC REF HP_VSS A_VDD LS_VDD HP_VDD MIC+ DAC REF MIC- CP+ CP0.5 - 50 MHz MCLK HPL Baseband Controller 2 I C MONO+ LM49352 HPR MONO- Multimedia IC LS+ LS- 2 8O I S / PCM (PORT1) EP+ EP- FM / Bluetooth Radio 32O 2 I S / PCM (PORT2) DGND LSGND AGND AUX_L AUX_R Synthesized TV Tuner Figure 3. Example Application in Multimedia Phone Using Multiple Media Sources 4 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 D_VDD I/O_VDD ADC REF HP_VSS A_VDD LS_VDD HP_VDD MIC+ DACREF MIC- CP+ CP0.5 - 50 MHz MCLK HPL 2 I C HPR Baseband Controller 2 I S / PCM (PORT1) LM49352 LS+ LS- MONO+ 8O MONOAUX_OUT+ AUX_OUTMultimedia IC 2 8O I S / PCM (PORT2) DGND LSGND AGND LM48310 AUX_L AUX_R Synthesized FM Radio / TV Tuner Figure 4. Example Application in a Multimedia Phone with Stereo Loudspeaker Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 5 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com D_VDD I/O_VDD ADC REF HP_VSS A_VDD LS_VDD HP_VDD MIC+ DACREF MIC- CP+ CP0.5 - 50 MHz MCLK HPL 2 I C HPR Multimedia Processor 2 I S / PCM (PORT1) LM49352 LS+ LS8O AUX_OUT+ AUX_OUT- Bluetooth Radio 2 8O I S / PCM (PORT2) DGND LSGND AGND LM48310 + AUX - + MONO - FM Radio / TV Tuner w/ Stereo Differential Outputs Figure 5. Example Application in a Portable Media Player with Stereo Loudspeakers Connection Diagrams Figure 6. 36 Bump DSBGA 6 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 1 2 3 4 5 6 A HPR AVDD AGND DAC REF ADC REF SDA B HPL AUXR AUXL PORT2 SYNC PORT2 SDI SCL C HPVSS HPVDD EP- PORT2 SDO PORT2 CLK MCLK D CP- CP+ EP+ PORT1 SYNC PORT1 SDO DGND E LSGND LSVDD MONO- MIC- PORT1 SDI DVDD F LS+ LS- MONO+ MIC+ PORT1 CLK IOVDD Figure 7. LM49352RL Pinout Diagram Top View (Bump Side Down) PIN DESCRIPTIONS Pin Pin Name Type Direction A1 HPR Analog Output Description A2 A_VDD Supply Input DAC (Analog), ADC (Analog), PLL (Analog), input stages, analog mixer (AUX and class D), and Earpiece amplifier power supply input A3 AGND Supply Input DAC (Analog), ADC (Analog), PLL (Analog), input stages, analog mixer (AUX and class D), and Earpiece amplifier ground A4 DAC REF Analog Input/Output A5 ADC REF Analog Input A6 SDA Digital Input/Output I2C interface data line B1 HPL Analog Output Headphone left output B2 AUX_R/AUX+ Analog Input Right analog input or positive differential auxiliary input B3 AUX_L/AUX- Analog Input Left analog input or negative differential auxiliary input B4 PORT2_SYNC Digital Input/Output B5 PORT2_SDI Digital Input Audio Port 2 serial data input B6 SCL Digital Input I2C interface clock line C1 HP_VSS Analog Output C2 HP_VDD Supply Input C3 EP-/AUXOUT- Analog Output C4 PORT2_SDO / GPIO Digital Input / Output C5 PORT2_CLK Digital Input/Output C6 MCLK Digital Input D1 CP- Analog Input/Output Fly capacitor negative input D2 CP+ Analog Input/Output Fly capacitor positive input D3 EP+/AUXOUT+ Analog Output D4 PORT1_SYNC Digital Input/Output D5 PORT1_SDO Digital Output Headphone right output Filter point for the DAC reference Filter point for the ADC reference. Connect this pin to A_VDD. Audio Port 2 sync signal (can be master or slave) Negative power supply pin for the headphone amplifier Headphone amplifier power supply pin Earpiece negative output or Auxiliary negative output Audio port 2 serial data output or General Purpose Input Output Audio port 2 clock signal (can be master or slave) Input clock from 0.5MHz to 50 MHz Earpiece positive output or Auxiliary positive output Audio Port 1 sync signal (can be master or slave) Audio Port 1 serial data output Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 7 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com PIN DESCRIPTIONS (continued) Pin Pin Name Type Direction D6 DGND Supply Input Digital ground Description E1 LSGND Supply Input Loudspeaker ground E2 LS_VDD Supply Input Loudspeaker amplifier and analog mixer (headphone) supply input E3 MONO- Analog Input Mono differential negative input E4 MIC- Analog Input Microphone negative input E5 PORT1_SDI Digital Input Audio Port 1 serial data input E6 D_VDD Supply Input DAC (Digital), ADC (Digital), PLL (Digital), digital mixer, DSP core, and I2C register power supply input F1 LS + Analog Output Loudspeaker positive output F2 LS - Analog Output Loudspeaker negative output F3 MONO+ Analog Input Mono differential positive input F4 MIC + Analog Input Microphone positive input F5 PORT1_CLK Digital Input/Output F6 I/O_VDD Supply Input Audio Port 1 clock signal (can be master or slave) Digital I/O (MCLK, I2S/PCM, I2C) interface power supply input PIN TYPE DEFINITIONS Analog Input -- A pin that is used by the analog and is never driven by the device. Supplies are part of this classification. Analog Output -- A pin that is driven by the device and should not be driven by external sources. Analog Input/Output -- A pin that is typically used for filtering a DC signal within the device. Passive components can be connected to these pins. Digital Input -- A pin that is used by the digital but is never driven by the device. Digital Output -- A pin that is driven by the device and should not be driven by another device to avoid contention. Digital Input/Output -- A pin that is either open drain (SDA) or a bidirectional CMOS in/out. In the latter case the direction is selected by a control register within the LM49352. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 8 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Absolute Maximum Ratings (1) (2) (3) Analog Supply Voltage (A_VDD and LS_VDD) 6.0V Digital Supply Voltage D_VDD 2.2V I/O Supply Voltage I/O_VDD 5.5V Headphone Supply Voltage HP_VDD 3.0V -65C to +150C Storage Temperature Power Dissipation (4) Internally Limited Human Body Model (5) ESD Ratings HPR and HPL pins 8kV All other pins 2.5kV Machine Model (6) 200V Junction Temperature 150C Thermal Resistance JA - RLA36 (soldered down to PCB with 2in2 1oz. copper plane) Soldering Information See Applications Note AN-1112 (Literature Number SNVA009). (1) (2) (3) (4) (5) (6) 60C/W "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in Absolute Maximum Ratings, whichever is lower. Human body model, applicable std. JESD22-A114C. Machine model, applicable std. JESD22-A115-A. Operating Ratings -40C to +85C Temperature Range Supply Voltage A_VDD, LS_VDD, and AVDD_REF 2.7V to 5.5V D_VDD 1.6V to 2.0V I/O_VDD 1.6V to 4.5V HP_VDD 1.7V to 2.8V Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 9 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Electrical Characteristics A_VDD = LS_VDD = 3.3V; HP_VDD = D_VDD = I/O_VDD = 1.8V (1) (2) The following specifications apply for RL(LS) = 8, RL(HP) = 32, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM49352 Symbol Parameter Conditions Typical (3) Limit (4) Units (Limit) DC CHARACTERISTICS (Digital current combines D_VDD and I/O_VDD. Analog current combines A_VDD, HP_VDD, and LS_VDD) DISD DIDD AISD Digital Shutdown Current Shutdown Mode, fMCLK = 13MHz, PLL Off Digital Active Current (MP3 Mode) fMCLK = 11.2896MHz, fS = 44.1kHz, Stereo DAC On, OSRDAC = 64, PLL Off, HP On 1.2 1.4 mA (max) Digital Active Current (FM Mode) fMCLK = 13MHz Analog Audio modes 0.2 0.5 mA (max) Digital Active Current (FM Record Mode) fMCLK = 12.288MHz, fS = 48kHz, Stereo ADC On, OSRADC = 128, PLL Off, Stereo Analog Inputs On 1.3 1.5 mA (max) Digital Active Current (CODEC Mode) fMCLK = 12.288MHz, fS = 8kHz, Mono ADC On, Mono DAC On, OSRDAC = 64 OSRADC = 128, PLL Off, MIC On 0.5 0.8 mA (max) Analog Shutdown Current Shutdown Mode 0.1 5 A (max) Analog Supply Current (MP3 Mode) 2 A fMCLK = 11.2896MHz, fS = 44.1kHz Stereo DAC On, OSRDAC = 64 PLL Off, Stereo HP On From A_VDD 4.3 6 mA (max) From HP_VDD 1.5 2.7 mA (max) From A_VDD 1.7 2.6 mA (max) From HP_VDD 1.5 2.7 mA (max) Analog Supply Current (FM Record Mode) fMCLK = 12.288MHz, fS = 48kHz, Stereo ADC On, OSRADC = 128, PLL Off, Stereo Analog Inputs On 7.2 9.3 mA (max) Analog Supply Current (CODEC Mode) fMCLK = 12.288MHz, fS = 8kHz, Mono ADC On, Mono DAC On, OSRDAC = 64 OSRADC = 128, PLL Off, MIC On, EP On 6.6 8.7 mA (max) From A_VDD 1.9 2.7 mA (max) 2 mA (max) Analog Supply Current (FM Mode) AIDD fMCLK = 13MHz, PLL Off Stereo Auxiliary Inputs On, PLL Off, Stereo HP On fMCLK = 13MHz, fPLLOUT = 12MHz, PLL On only PLLIDD PLL Total Active Current From D_VDD 1.4 HPIDD Headphone Quiescent Current Stereo HP On only 1.5 mA LSIDD Loudspeaker Quiescent Current LS On only 2.2 mA MICIDD Microphone Quiescent Current Mono MIC 0.4 mA (1) (2) (3) (4) 10 "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. Typical values represent most likely parametric norms at TA = +25C, and at the Recommended Operation Conditions at the time of product characterization and are not ensured. Datasheet min/max specification limits are specified by test or statistical analysis. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Electrical Characteristics A_VDD = LS_VDD = 3.3V; HP_VDD = D_VDD = I/O_VDD = 1.8V(1)(2) (continued) The following specifications apply for RL(LS) = 8, RL(HP) = 32, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM49352 Symbol Parameter Conditions Typical (3) Limit (4) Units (Limit) fS = 48kHz, Stereo ADCIDD ADC Total Active Current From A_VDD 5.8 mA From D_VDD 1.3 mA From A_VDD 3.1 mA From D_VDD 1 mA fS = 48kHz, Stereo DACIDD DAC Total Active Current AUXINIDD Mono/Auxiliary Input Amplifier Quiescent Current Mono and AUX Input Amplifiers enabled 0.6 mA AUXOUTIDD Auxiliary Output Amplifier Quiescent Current AUXOUT enabled 0.4 mA Earpiece Mode 1.1 mA 93 % 0.03 % LOUDSPEAKER AMPLIFIER LSEFF Loudspeaker Efficiency PO = 970mW, RL = 8, LS_VDD = 4.2V THD+N Total Harmonic Distortion + Noise PO = 300mW, f = 1kHz, RL = 8, Mono Input Signal RL = 8, f = 1kHz, THD+N = 1%, Mono Input Signal PO PSRR Output Power Power Supply Rejection Ratio LS_VDD = 5V 1.4 LS_VDD = 4.2V 970 LS_VDD = 3.3V 590 W mW 510 mW (min) RL = 4, f = 1kHz, THD+N = 1%, Mono Input Signal LS_VDD = 5V 2.4 LS_VDD = 4.2V 1.65 W W LS_VDD = 3.3V 980 mW VRIPPLE = 200mVP-P fRIPPLE = 217Hz Mono Input Terminated VREF = 1.0F, Input Referred LS Gain = 12dB 75 VRIPPLE = 200mVP-P fRIPPLE = 217Hz From DAC, DAC gain = 0dB 74 dB LS_VDD = 4.2V 95 dB LS_VDD = 3.3V 93 60 dB (min) Reference = VOUT (1% THD+N ) Mono gain = 0dB, A-weighted Mono Input Terminated, LS Gain = 8dB SNR Signal-to-Noise Ratio dB (min) LS_VDD = 4.2V 91 dB LS_VDD = 3.3V 89 dB Output Noise Mono gain = 0dB, A-weighted, Mono Input Terminated, Input Referred 43 V Offset Voltage Mono gain = 0dB, from Mono Input 10 eOS VOS 88 Reference = VOUT (1% THD+N ) DAC Gain = 0dB, A-weighted fS = 48kHz, OSR = 128 LS Gain = 8dB 50 mV (max) Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 11 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Electrical Characteristics A_VDD = LS_VDD = 3.3V; HP_VDD = D_VDD = I/O_VDD = 1.8V(1)(2) (continued) The following specifications apply for RL(LS) = 8, RL(HP) = 32, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM49352 Symbol Parameter Conditions Typical Limit (4) Units (Limit) 0.025 0.1 % (max) (3) HEADPHONE AMPLIFIERS THD+N Total Harmonic Distortion + Noise PO = 15mW, f = 1kHz, RL = 32 Stereo Analog Input Signal RL = 32, f = 1kHz, THD+N = 1%, Stereo Analog Input Signal, In phase PO Headphone Output Power HP_VDD = 2.8V 65 HP_VDD = 1.8V 24 mW 20 mW (min) RL = 16, f = 1kHz, THD+N = 1%, Stereo Analog Input Signal, In phase HP_VDD = 2.8V 73 mW HP_VDD = 1.8V 24 mW VRIPPLE = 200mVP-P, fRIPPLE = 217Hz Mono Input Terminated, Mono gain = 0dB VREF = 1.0F, Mono Differential Input Mode, PSRR Power Supply Rejection Ratio Ripple applied to AVDD only 100 Ripple applied to AVDD and HPVDD 88 85 dB (min) dB Ripple applied to AVDD HPVDD, and DVDD 81 dB Reference = VOUT (1% THD+N ) Gain = 0dB, A-weighted Stereo Inputs Terminated 98 93 dB (min) Reference = VOUT (1% THD+N) Gain = 0dB, A-weighted, I2S Input = Digital Zero 97 93 dB (min) Gain = 0dB, A-weighted, Stereo Inputs Terminated 11 V Gain = 0dB, A-weighted, I2S Input = Digital Zero 12 V PO = 7.5mW, f = 1kHz, RL = 32 Stereo Analog Input Signal 85 dB 0.03 dB VRIPPLE = 200mVP-P, fRIPPLE = 217Hz From DAC, DAC gain = 0dB SNR Signal to Noise Ratio eOS Output Noise XTALK Crosstalk ACH-CH Channel-to-Channel Gain Matching VOS 12 Output Offset Voltage AUX Gain = 0dB From mono Input 1.4 6 mV (max) DAC Gain = 0dB From DAC Input, fMCLK = 12.288MHz 1.6 6 mV (max) Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Electrical Characteristics A_VDD = LS_VDD = 3.3V; HP_VDD = D_VDD = I/O_VDD = 1.8V(1)(2) (continued) The following specifications apply for RL(LS) = 8, RL(HP) = 32, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM49352 Symbol Parameter Conditions Typical (3) Limit (4) Units (Limit) AUXILIARY OUTPUT/EARPIECE AMPLIFIER THD+N POUT PSRR Total Harmonic Distortion Output Power Power Supply Rejection Ratio AUX_LINE_OUT, f = 1kHz From Mono In RL = 5k, VOUT = 1VRMS 0.002 % Earpiece mode, f = 1kHz From Mono In RL = 32 BTL, POUT = 20mW 0.02 % Earpiece mode, f = 1kHz RL = 32 BTL, THD+N = 1% 58 VRIPPLE = 200mVP-P, fRIPPLE = 217Hz Mono Input terminated, CREF = 1.0F AUX_LINE_OUT 100 VRIPPLE = 200mVP-P, fRIPPLE = 217Hz Mono Input terminated, CREF = 1.0F Earpiece mode, -6dB cut enabled 100 50 mW (min) dB 90 dB SNR Signal to Noise Ratio Gain = 0dB, VREF = VOUT (1% THD+N) A-weighted, Mono Input Terminated 105 dB OUT Output Noise Gain = 0dB, VREF = VOUT (1% THD+N) A-weighted, Mono Input Terminated 7 V MONO gain = 0dB, From Mono Input AUX_LINE_OUT 4 mV Gain = 0dB, From Mono Input Earpiece mode 4 Turn-On time PMC Clock = 300kHz 28 ms THD+NADC ADC Total Harmonic Distortion + Noise Mono Differential Input VIN = 1VRMS, f = 1kHz Gain = 0dB, fS = 48kHz 0.007 % PBADC ADC Passband 220 Hz RADC ADC Ripple VOS TWU Output Offset Voltage 12 mV (max) STEREO ADC HPF On, fS = 48kHz Lower -3dB Point HPF On, Upper -3dB Point SNRADC ADCLEVEL ADC Signal to Noise Ratio 0.41*fS kHz OSRDAC = 128 0.1 dB Reference = VOUT (0dBFS ) Gain = 6dB, A-weighted From MIC, fS = 8kHz 98 dB Reference = VOUT (0dBFS ) Gain = 0dB, A-weighted From Stereo Input, fS = 48kHz 97 dB 1.6 VRMS 0.01 % VRMS ADC Full Scale Input Level STEREO DAC I2S Input, AUXOUT, OSRDAC = 64 VIN = 500mFFSRMS, f = 1kHz Gain = 0dB THD+NDAC DAC Total Harmonic Distortion + Noise DACLEVEL DAC Full Scale Output Level 1.08 RDAC DAC Ripple 0.1 dB PBDAC DAC Passband Upper -3dB Point 0.45*fS kHz SNRDAC DAC Signal to Noise Ratio fS = 48kHz, A-weighted, AUXOUT 103 dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 13 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Electrical Characteristics A_VDD = LS_VDD = 3.3V; HP_VDD = D_VDD = I/O_VDD = 1.8V(1)(2) (continued) The following specifications apply for RL(LS) = 8, RL(HP) = 32, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM49352 Symbol Parameter Conditions Typical (3) Limit (4) Units (Limit) VOLUME CONTROL VCRAUX VCRMONO Stereo Input Volume Control Range MONO Input Volume Control Range VCRDAC DAC Volume Control Range VCRADC ADC Volume Control Range Minimum Gain -46.5 dB Maximum Gain 18 dB Minimum Gain -46.5 dB Maximum Gain 18 dB Minimum Gain -76.5 dB Maximum Gain 18 dB Minimum Gain -76.5 dB Maximum Gain 18 dB Minimum Gain 6 dB VCRMIC MIC Volume Control Range Maximum Gain 36 dB VCRLS Loudspeaker Amplifier Volume Control Range Minimum Gain 0 dB Maximum Gain 12 dB VCRHP Headphone Amplifier Volume Control Range Minimum Gain -18 dB Maximum Gain 0 dB SSLS Loudspeaker Amplifier Volume Control Stepsize 4 dB SSHP Headphone Amplifier Volume Control Stepsize Refer to Table 19 dB SSAUX AUX Input Volume Control Stepsize 1.5 dB SSMONO MONO Input Volume Control Stepsize 1.5 dB SSDAC DAC Volume Control Stepsize 1.5 dB SSADC ADC Volume Control Stepsize 1.5 dB SSMIC MIC Volume Control Stepsize 2 dB SVAUX AUX Volume Setting Variation 1 SVMONO MONO Volume Setting Variation 1 dB (min) SVMIC MIC Volume Setting Variation 1 dB (max) dB (max) ANALOG INPUTS AUX_RIN MONO_RIN MIC_RIN 14 Auxiliary Input Impedance Mono Input Impedance Microphone Input Impedance AUX Gain = 18dB 10 k AUX Gain = 0dB 38 k AUX Gain = -46.5dB 64 k MONO Gain = 18dB 10 k MONO Gain = 0dB 38 k MONO Gain = -46.5dB 64 k All MIC gain settings 50 k Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics Class D Loudspeaker Amplifier Efficiency vs Output Power THD+N < 10%, RL = 8 Green >> LSVDD = 3.3V Gray >> LSVDD = 4.2V Blue >> LSVDD = 5V DAC Frequency Response fS = 48kHz Blue >> OSR = 64 Light Blue >> OSR = 128 +1 100 90 +0.5 70 MAGNITUDE (dB) EFFICIENCY (%) 80 60 50 40 30 +0 -0.5 20 10 0 -1 0 400 800 1200 1600 2000 20 FREQUENCY (Hz) Figure 9. DAC Frequency Response fS = 8kHz Blue >> OSR = 64 Light Blue >> OSR = 128 DAC THD+N vs Frequency fS = 8kHz, OSR = 128 I2S Input = 500mFFS +1 10 +0.5 1 +0 0.1 0.01 -0.5 -1 20 5k 10k 20k Figure 8. THD+N (%) MAGNITUDE (dB) OUTPUT POWER (mW) 50 100 200 500 1k 2k 0.001 50 100 200 500 1k 2k 4k 20 FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 10. Figure 11. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 15 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) DAC THD+N vs Input Level fS = 48kHz, OSR = 64 I2S Input = 1kHz 10 10 1 1 THD+N (%) THD+N (%) DAC THD+N vs Frequency fS = 8kHz, OSR = 64 I2S Input = 500mFFS 0.1 0.01 0.1 0.01 0.001 20 50 100 200 500 1k 2k 0.001 10m 5k 10k 20k 20m FREQUENCY (Hz) 1 INPUT VOLTAGE (FFS) Figure 13. Stereo Audio ADC Frequency Response fS = 48kHz, OSR = 64 From MIC, MIC Gain = 6dB, CIN = 1F Stereo Audio ADC Frequency Response fS = 8kHz, OSR = 128 From MIC, MIC Gain = 6dB, CIN = 1F +1 +0 MAGNITUDE (dB) +0 MAGNITUDE (dB) 500m Figure 12. +1 -1 -1 -2 -2 -3 20 50 100 200 500 1k 2k 5k 10k 20k -3 20 50 100 200 500 1k 2k 4k FREQUENCY (Hz) FREQUENCY (Hz) Figure 14. 16 50m 100m 200m Figure 15. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics (continued) +1 Mono Voice ADC Frequency Response fS = 48kHz, OSR = 128 From MIC, MIC Gain = 6dB, CIN = 1F +1 +0 MAGNITUDE (dB) MAGNITUDE (dB) +0 -1 -1 -2 -2 -3 20 -3 20 50 100 200 500 1k 2k 5k 10k 20k 50 100 200 500 1k 2k 5k 10k 20k Figure 16. FREQUENCY (Hz) Figure 17. Stereo Audio HPF ADC Frequency Response fS = 48kHz, OSR = 128 From MONO/AUX, MONO>AUX Gain = 0dB, CIN = 1F Blue >> No HPF Light Blue >> HPF Mode = '101' Green >> HPF Mode = '110' Light Green >> HPF Mode = '111' Mono Voice HPF ADC Frequency Response fS = 48kHz, OSR = 128 From MIC, MIC Gain = 6dB, CIN = 1F Gray >> No HPF Blue >> HPF Mode = '000' Light Blue >> HPF Mode = '001' Green >> HPF Mode = '010' Light Green >> HPF Mode = '011' Yellow >> HPF Mode = '100' FREQUENCY (Hz) +1 +1 +0 +0 MAGNITUDE (dB) MAGNITUDE (dB) Mono Voice ADC Frequency Response fS = 8kHz, OSR = 128 From MIC, MIC Gain = 6dB, CIN = 1F -1 -2 -3 20 -1 -2 50 100 200 500 1k 2k 5k 10k 20k -3 20 FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 18. Figure 19. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 17 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Mono Voice HPF ADC Frequency Response fS = 8kHz, OSR = 128 From MIC, MIC Gain = 6dB, CIN = 1F Gray >> No HPF Blue >> HPF Mode = '000' Light Blue >> HPF Mode = '001' Green >> HPF Mode = '010' Light Green >> HPF Mode = '011' Yellow >> HPF Mode = '100' ADC THD+N vs Frequency fS = 48kHz, OSR = 128 From MONO/AUX, MONO/AUX Gain = 6dB, VIN = 1VRMS +1 10 1 THD+N (%) MAGNITUDE (dB) +0 -1 -2 -3 20 0.1 0.01 0.001 50 100 200 500 1k 2k 5k 10k 20k 20 FREQUENCY (Hz) FREQUENCY (Hz) Figure 21. ADC THD+N vs Frequency fS = 48kHz, OSR = 128 From MIC, MIC Gain = 6dB, VIN = 500mVRMS ADC THD+N vs Input Voltage fS = 48kHz, OSR = 128 From MONO/AUX, MONO/AUX Gain = 0dB, fIN = 1kHz 10 1 1 THD+N (%) THD+N (%) 5k 10k 20k Figure 20. 10 0.1 0.01 0.1 0.01 0.001 20 50 100 200 500 1k 2k 5k 10k 20k 0.001 1m FREQUENCY (Hz) 5m 10m 50m100m 500m 1 2 INPUT VOLTAGE (Vrms) Figure 22. 18 50 100 200 500 1k 2k Figure 23. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics (continued) ADC THD+N vs Input Voltage fS = 48kHz, OSR = 128 From MIC, MIC Gain = 6dB, VIN = 1kHz 10 Loudspeaker THD+N vs Input Voltage From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, LSVDD = 3.3V, POUT = 300VRMS, RL = 8 10 1 THD+N (%) THD+N (%) 1 0.1 .01 .001 20 0.1 .01 100 1k .001 20 10k 20k 100 FREQUENCY (Hz) Figure 24. Loudspeaker THD+N vs Input Voltage From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, LSVDD = 5V, POUT = 300VRMS, RL = 8 10 1 1 THD+N (%) THD+N (%) 10k 20k FREQUENCY (Hz) Figure 25. Loudspeaker THD+N vs Input Voltage From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, LSVDD = 4.2V, POUT = 300VRMS, RL = 8 10 0.1 .01 .001 20 1k 0.1 .01 100 1k 10k 20k .001 FREQUENCY (Hz) Figure 26. 20 100 1k 10k 20k FREQUENCY (Hz) Figure 27. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 19 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Loudspeaker THD+N vs Output Power From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, fIN = 1kHz, RL = 8 Blue >> LSVDD = 3.3V Light Blue >> LSVDD = 4.2V Green >> LSVDD = 5V 10 10 1 1 THD+N (%) THD+N (%) Loudspeaker THD+N vs Input Voltage From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, LSVDD = 3.3V, POUT = 300VRMS, RL = 4 0.1 0.1 0.01 .01 0.001 10m .001 20 100 1k 10k 20k 100m 1 2 3 OUTPUT POWER (W) FREQUENCY (Hz) Figure 28. Figure 29. Loudspeaker THD+N vs Output Power fS = 48kHz, OSR = 128 From MONO/AUX Input, MONO/AUX Gain = 0dB LS Gain = 8dB, fIN = 1kHz, RL = 4 Blue >> LSVDD = 3.3V Light Blue >> LSVDD = 4.2V Green >> LSVDD = 5V Loudspeaker PSRR vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, LS Gain = 12dB LSVDD = 3.3V, VRIPPLE = 200mVPP, Input Referred 10 0 -10 -20 -30 PSRR (dB) THD+N (%) 1 0.1 -40 -50 -60 -70 0.01 -80 -90 0.001 10m 100m 1 2 3 -100 OUTPUT POWER (W) 100 1k 10k 100k FREQUENCY (Hz) Figure 30. 20 20 Figure 31. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Loudspeaker PSRR vs Frequency fS = 48kHz, OSR = 128 MONO/AUX Input, MONO/AUX Gain = 0dB, LS Gain = 12dB LSVDD = 4.2V, VRIPPLE = 200mVPP, Input Referred 0 -10 -10 -20 -20 -30 -30 PSRR (dB) PSRR (dB) 0 Loudspeaker PSRR vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, LS Gain = 12dB LSVDD = 5V, VRIPPLE = 200mVPP, Input Referred -40 -50 -60 -40 -50 -60 -70 -70 -80 -80 -90 -90 -100 -100 20 100 1k 10k 100k 20 FREQUENCY (Hz) 100 1k 10k 100k FREQUENCY (Hz) Figure 32. Figure 33. Headphone PSRR vs Frequency DAC Input, DAC Gain = 0dB, LS Gain = 12dB LSVDD = 3,3V, AVDD = 3.3V, DVDD = 1.8V, VRIPPLE = 200mVPP Ripple on LSVDD, AVDD, DVDD, Input Referred HeadphoneTHD+N vs Frequency MONO/AUX, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 3.3V, POUT = 15mW, RL = 32 Stereo In Phase 0 10 -10 -20 1 THD+N (%) PSRR (dB) -30 -40 -50 -60 0.1 -70 .01 -80 -90 -100 20 100 1k 10k 100k .001 20 100 1k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 34. Figure 35. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 21 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Headphone THD+N vs Frequency MONO/AUX, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 1.8V, POUT = 15mW, RL = 16 Stereo In Phase 10 10 1 1 THD+N (%) THD+N (%) Headphone THD+N vs Frequency MONO/AUX, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 2.8V, POUT = 15mW, RL = 32 Stereo In Phase 0.1 0.1 .01 .01 .001 20 .001 100 1k 20 10k 20k 100 10k 20k FREQUENCY (Hz) Figure 36. Figure 37. Headphone THD+N vs Frequency MONO/AUX, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 2.8V, POUT = 15mW, RL = 16 Stereo in Phase Headphone THD+N vs Output Power MONO/AUX Input, MONO/AUX Gain = 0dB, HP Gain = 0dB Stereo In Phase, fIN = 1kHz, RL = 32 Blue >> HPVDD = 1.8V Light Blue >> HPVDD = 2.8V 10 10 1 1 THD + N (%) THD+N (%) FREQUENCY (Hz) 1k 0.1 0.1 0.01 .01 .001 20 100 1k 10k 20k 0.001 1m 2m 5m 10m 100m OUTPUT POWER (W) FREQUENCY (Hz) Figure 38. 22 Figure 39. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Headphone THD+N vs Output Power MONO/AUX Input, MONO/AUX Gain = 0dB, HP Gain = 0dB Stereo In Phase, fIN = 1kHz, RL = 16 Blue >> HPVDD = 1.8V Light Blue >> HPVDD = 2.8V Headphone PSRR vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 1.8V, AVDD = 3.3V, VRIPPLE = 200mVPP Ripple on HPVDD, AVDD 0 10 -10 -20 -30 PSRR (dB) THD + N (%) 1 0.1 -40 -50 -60 -70 0.01 -80 -90 0.001 1m 2m 5m 10m -100 20 100m 100 1k 10k 100k OUTPUT POWER (W) FREQUENCY (Hz) Figure 41. Headphone PSRR vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 1.8V, AVDD = 3.3V, VRIPPLE = 200mVPP Ripple on AVDD only Headphone PSRR vs Frequency DAC Input, DAC Gain = 0dB, HP Gain = 0dB HPVDD = 1.8V, AVDD = 3.3V, DVDD = 1.8V, VRIPPLE = 200mVPP Ripple on HPVDD, AVDD, DVDD -20 0 -30 -10 -40 -20 -50 -30 PSRR (dB) PSRR (dB) Figure 40. -60 -70 -80 -40 -50 -60 -90 -70 -100 -80 -110 -90 -120 20 100 1k 10k 100k -100 20 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 42. Figure 43. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 23 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Headphone Crosstalk vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, HP Gain = 0dB HPVDD = 1.8V, AVDD = 3.3V, POUT = 15mW, RL = 32 0 Earpiece THD+N vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = 0dB AVDD = 3.3V, POUT = 20mW, RL = 32 Earpiece Mode 10 -10 -20 1 THD+N (%) CROSSTALK (dB) -30 -40 -50 -60 0.1 -70 .01 -80 -90 -100 20 .001 100 1k 20 10k 20k 100 FREQUENCY (Hz) 1k 10k 20k FREQUENCY (Hz) Figure 44. Figure 45. Earpiece THD+N vs Output Power MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = 0dB AVDD = 3.3V, fIN = 1kHz, RL = 32 Earpiece Mode 10 Earpiece PSRR vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = -6dB AVDD = 3.3V, VRIPPLE = 200mVPP, Earpiece Mode -20 -30 -40 -50 PSRR (dB) THD + N (%) 1 0.1 -60 -70 -80 -90 0.01 -100 -110 0.001 1m 2m 5m 10m 100m -120 20 100 1k 10k 100k OUTPUT POWER (W) FREQUENCY (Hz) Figure 47. Figure 46. 24 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Auxiliary Output THD+N vs Output Voltage MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = 0dB AVDD = 3.3V, fIN = 1kHz, RL = 5k AUXOUT Mode 10 10 1 1 THD+N (%) THD+N (%) Auxiliary Output THD+N vs Frequency MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = 0dB AVDD = 3.3V, VOUT = 1VRMS, RL = 5k AUXOUT Mode 0.1 0.01 .01 .001 20 0.1 100 0.001 10m 10k 20k 1k 100m 1 2 3 OUTPUT VOLTAGE (VRMS) FREQUENCY (Hz) Figure 48. Figure 49. Auxiliary Output PSRR vs FRequency MONO/AUX Input, MONO/AUX Gain = 0dB, EP Gain = 0dB AVDD = 3.3V, VRIPPLE = 200mVPP, AUXOUT Mode -20 -30 -40 PSRR (dB) -50 -60 -70 -80 -90 -100 -110 -120 20 100 1k 10k 100k FREQUENCY (Hz) Figure 50. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 25 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com SYSTEM CONTROL Method 1. I2C Compatible Interface I2C SIGNALS In I2C mode the LM49352 pin SCL is used for the I2C clock SCL and the pin SDA is used for the I2C data signal SDA. Both these signals need a pull-up resistor according to I2C specification. The I2C slave address for LM49352 is 00110102. I2C DATA VALIDITY The data on SDA line must be stable during the HIGH period of the clock signal (SCL). In other words, state of the data line can only be changed when SCL is LOW. SCL SDA data change allowed data valid data change allowed data valid data change allowed Figure 51. I2C Signals: Data Validity I2C START AND STOP CONDITIONS START and STOP bits classify the beginning and the end of the I2C session. START condition is defined as SDA signal transitioning from HIGH to LOW while SCL line is HIGH. STOP condition is defined as the SDA transitioning from LOW to HIGH while SCL is HIGH. The I2C master always generates START and STOP bits. The I2C bus is considered to be busy after START condition and free after STOP condition. During data transmission, I2C master can generate repeated START conditions. First START and repeated START conditions are equivalent, function-wise. SDA SCL S P START condition STOP condition Figure 52. I2C Start and Stop Conditions TRANSFERRING DATA Every byte put on the SDA line must be eight bits long, with the most significant bit (MSB) being transferred first. Each byte of data has to be followed by an acknowledge bit. The acknowledge related clock pulse is generated by the master. The transmitter releases the SDA line (HIGH) during the acknowledge clock pulse. The receiver must pull down the SDA line during the 9th clock pulse, signifying an acknowledge. A receiver which has been addressed must generate an acknowledge after each byte has been received. After the START condition, the I2C master sends a chip address. This address is seven bits long followed by an eight bit which is a data direction bit (R/W). The LM49352 address is 00110102. For the eighth bit, a "0" indicates a WRITE and a "1" indicates a READ. The second byte selects the register to which the data will be written. The third byte contains data to write to the selected register. 26 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 MSB LSB ADR6 Bit7 ADR5 bit6 ADR4 bit5 ADR3 bit4 ADR2 bit3 ADR1 bit2 ADR0 bit1 R/W bit0 2 I C SLAVE address (chip address) Figure 53. I2C Chip Address Register changes take effect at the SCL rising edge during the last ACK from slave. ack from slave ack from slave start MSB Chip Address LSB w ack MSB Register 0x02h LSB ack start slave address = 00110102 w ack ack from slave MSB Data LSB ack stop ack stop SCL SDA register address = 0x02h ack register 0x02h data w = write (SDA = "0") r = read (SDA = "1") ack = acknowledge (SDA pulled down by slave) rs = repeated start Figure 54. Example I2C Write Cycle When a READ function is to be accomplished, a WRITE function must precede the READ function, as shown in the Read Cycle waveform. ack from slave repeated start ack from slave start MSB Chip Address LSB w ack MSB Register 0x00h LSB ack rs ack from slave data from slave ack from master MSB Chip Address LSB r ack MSB Data LSB ack stop SCL SDA start slave address = 00110102 w ack register address = 0x00h ack rs slave address = 00110102 r ack register 0x00h data ack stop Figure 55. Example I2C Read Cycle SDA 10 8 7 6 1 8 2 7 SCL 5 1 3 4 9 Figure 56. I2C Timing Diagram I2C TIMING PARAMETERS Symbol Parameter Limit Min Typ Max Units Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 27 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 1 Hold Time (repeated) START Condition 0.6 s 2 Clock Low Time 1.3 s 3 Clock High Time 600 ns 4 Setup Time for a Repeated START Condition 600 5 (1) www.ti.com ns Data Hold Time (Output direction, delay generated by LM49352) See (1) 50 ns Data Hold Time (Input direction, delay generated by the Master) 50 ns 6 Data Setup Time 100 7 Rise Time of SDA 300 ns 8 Fall Time of SDA 300 ns 9 Set-up Time for STOP condition 600 ns 10 Bus Free Time between a STOP and a START Condition 1.3 s ns Data ensured by fall time. Device Register Map Table 1. Device Register Map Address Register 7 6 5 4 PMC CHIP PORT2 PORT1 SETUP ACTIVE CLK OVR CLK OVR 3 2 1 0 MCLK OSC CHIP ENB PLL_P2 ENB PLL OVR ENB ENABLE BASIC SETUP 0x00h 0x01h PMC CLOCKS 0x02h PMC CLK_DIV PMC_CLK_SEL PMC_CLK_DIV(R) PLL 0x03h PLL_CLK_SEL 0x04h PLL M 0x05h PLL N 0x06h PLL N_MOD 0x07h PLL P 0x08h PLL P2 PLL M PLL N PLL P2[8] PLL P1[8] PLL N_MOD PLL P1 [7:0] PLL P2[7:0] ANALOG MIXER 0x10h CLASSD AUX_LS MONO_LS DACL_LS DACR_LS 0x11h HEAD PHONESL AUX_HPL MONO _HPL DACL_HPL DACR_HPL 0x12h HEAD PHONESR AUX_HPR MONO _HPR DACL _HPR DACR _HPR 0x13h AUX_OUT AUX_AUX MONO _AUX DACL_AUX DACR _AUX 0x14h OUTPUT OPTIONS 0x15h ADC MONO _ADCL AUX _ADCR 0x16h MIC_LVL MUTE SE/DIFF 0x18h AUXL_LVL 0x19h MONO_LV 0x1Bh HP _SENSE 0x20h ADC BASIC LS_LEVEL MIC_AUX AUX_LINE_ AUX_NEG_ OUT 6dB LR_HP_LEVEL MIC_ADCL MIC_ADCR RSVD DACL _ADCL DACR _ADCR MIC_LEVEL SE/DIFF AUX_LEVEL AUXL_MON SE/DIFF O_IN MONO_LEVEL HP SENSE _AUX_D HP SENSE _AUX HP SENSE_D HP SENSE MUTE_R MUTE_L ADC_OSR MONO ADC 28 DSPONLY ADC_CLK_SEL Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 1. Device Register Map (continued) Address Register 0x21h ADC CLOCK 7 6 5 4 3 2 0x23h ADC _MIXER 0x30h DAC _BASIC 0x31h DAC _CLOCK 0x40h IPLVL1 PORT2_RX_R_LVL 0x41h IPLVL2 INTERP_L_LVL 0x42h OPPORT1 MONO SWAP 0x43h OPPORT2 MONO SWAP R_SEL 0x44h OPDAC ADCR PORT2R 0x45h OPDECI 1 0 ADC_CLK_DIV (T) STEREO _LINK ADC_MIX_LEVEL_R ADC_MIX_LEVEL_L DAC DSPONLY DAC_CLK_SEL MUTE_R MUTE_L DAC_OSR DAC_CLK_DIV (S) DIGITAL MIXER SWAP PORT2_RX_L_LVL PORT1_RX_R_LVL PORT1_RX_L_LVL INTERP_R_LVL ADC_R_LVL ADC_L_LVL R_SEL L_SEL PORT1R MXRCLK_SEL L_SEL ADCL PORT2L R_SEL PORT1L L_SEL AUDIO PORT 1 STEREO _SYNC _MODE STEREO _SYNC _PHASE 0x50h BASIC CLK_PH SYNC_MS CLK_MS 0x51h CLK_GEN1 0x52h CLK_GEN2 0x53h SYNC _GEN 0x54h DATA _WIDTH 0x55h RX_MODE A/ULAW COMPAND MSB_POSITION RX_MODE 0x56h TX_MODE A/ULAW COMPAND MSB_POSITION TX_MODE 0x60h BASIC STEREO _SYNC _MODE STEREO _SYNC _PHASE 0x61h CLK_GEN1 CLK_SEL TX_ENB RX_ENB STEREO HALF_CYCLE_DIVDER SYNTH _DENOM SYNTH_NUM SYNC_WIDTH(MONO MODE) SYNC_RATE TX_WIDTH RX_WIDTH TX_EXTRA_BITS AUDIO PORT 2 CLK_PH SYNC_MS CLK_MS CLK_SEL TX_ENB RX_ENB STEREO HALF_CYCLE_DIVDER SYNTH_DE NOM 0x62h CLK_GEN2 SYNTH_NUM 0x63h SYNC _GEN 0x64h DATA _WIDTH 0x65h RX_MODE A/ULAW COMPAND MSB_POSITION RX_MODE 0x66h TX_MODE A/ULAW COMPAND MSB_POSITION TX_MODE SYNC_WIDTH (MONO MODE) SYNC_RATE TX_WIDTH RX_WIDTH TX_EXTRA_BITS EFFECTS ENGINE 0x70h ADC FX ADC SCLP ENB ADC EQ ENB ADC PK ENB ADC ALC ENB ADC HPF_ENB 0x71h DAC FX DAC SCLP ENB RSVD DAC EQ ENB DAC PK ENB DAC ALC ENB 0x80h HPF 0x81h ADC ALC 1 0x82h ADC ALC 2 ADC EFFECTS HPF MODE SOURCE OVR SOURCE RSEL SOURCE LSEL STEREO LINK NG_ENB LIMITER ADC_SAMPLE NOISE_FLOOR Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 29 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 1. Device Register Map (continued) Address Register 0x83h ADC ALC 3 7 6 5 4 3 ALC_TARGET_LEVEL 0x84h ADC ALC 4 ATTACK_RATE 0x85h ADC ALC 5 0x86h ADC ALC 6 0x87h ADC ALC 7 MAX_LEVEL 0x88h ADC ALC 8 MIN_LEVEL 0x89h ADC L LEVEL 0x8Ah ADC R LEVEL PK_DECAY_RATE 2 1 0 DECAY_RATE/RELEASE_RATE HOLDTIME STEREO LINK ADC_L_LEVEL ADC_R_LEVEL 0x8Bh EQ BAND 1 LEVEL FREQ 0x8Ch EQ BAND 2 Q LEVEL FREQ 0x8Dh EQ BAND 3 Q LEVEL FREQ 0x8Eh EQ BAND 4 Q LEVEL FREQ 0x8Fh EQ BAND 5 LEVEL FREQ 0x90h SOFTCLIP 1 SOFT KNEE 0x91h SOFTCLIP 2 RATIO 0x92h SOFTCLIP 3 LEVEL 0x98h LVLMONL 0x99h LVLMONR THRESHOLD ADC EFFECT MONITORS ADC LEFT LEVEL MONITOR ADC RIGHT LEVEL MONITOR 0x9Ah FXCLIP SCLP _R CLIP SCLP _L CLIP EQ _R CLIP EQ _L CLIP GAIN _R CLIP GAIN _L CLIP ADC _R CLIP 0x9Bh ALCMONL SCLP_R DISTORT SCLP_L DISTORT ADC LEFT ALC MONITOR 0x9Ch ALCMONR SCLP_L DISTORT SCLP_R DISTORT ADC RIGHT ALC MONITOR 0xA0h DAC ALC 1 STEREO LINK 0xA1h DAC ALC 2 NG_ENB 0xA2h DAC ALC 3 AGC_TARGET_LEVEL 0xA3h DAC ALC 4 ATTACK_RATE 0xA4h DAC ALC 5 0xA5h DAC ALC 6 0xA6h DAC ALC 7 MAX_LEVEL 0xA7h DAC ALC 8 MIN_LEVEL 0xA8h DAC L LEVEL ADC _L CLIP DAC EFFECTS 30 PK_DECAY_RATE LIMITER DAC_SAMPLE NOISE_FLOOR DECAY_RATE/RELEASE_RATE HOLDTIME STEREO LINK DAC_L_LEVEL Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 1. Device Register Map (continued) Address Register 0xA9h DAC R LEVEL 7 6 5 4 3 2 1 0 DAC_R_LEVEL 0xABh EQ BAND 1 LEVEL FREQ 0xACh EQ BAND 2 Q LEVEL FREQ 0xADh EQ BAND 3 Q LEVEL FREQ 0xAEh EQ BAND 4 Q LEVEL FREQ 0xAFh EQ BAND 5 LEVEL FREQ 0xB0h SOFTCLIP 1 SOFT KNEE 0xB1h SOFTCLIP 2 RATIO 0xB2h SOFTCLIP 3 LEVEL 0xB8h LVLMONL 0xB9h LVLMONR THRESHOLD DAC EFFECT MONITORS DAC LEFT LEVEL MONITOR DAC RIGHT LEVEL MONITOR 0xBAh FXCLIP SCLP _R CLIP SCLP _L CLIP EQ _R CLIP EQ _L CLIP 0xBBh ALCMONL SCLP_R DISTORT SCLP_L DISTORT DAC LEFT ALC MONITOR 0xBCh ALCMONR SCLP_L DISTORT SCLP_R DISTORT DAC RIGHT ALC MONITOR 0xE0h GPIO1 GPIO_RX GPIO_TX 0xE1h GPIO2 RSVD GAIN _R CLIP GAIN _L CLIP TEMP SHORT RSVD RSVD RSVD SS _DISABLE RSVD RSVD CPFORCE DACREF RSVD GPIO GPIO_MODE SPREAD SPECTRUM 0xF0h RESET 0xF1h SS 0xFEh FORCE SOFT _RESET RSVD RSVD RSVD Unless otherwise specified, the default values of the I2C registers is 0x00h. Table 2. Nonzero I2C Default Registers Address Register Default Data Value 0x02h PMC_CLK_DIV 0x50h 0x30h DAC_BASIC 0x02h 0x31h DAC_CLOCK 0x03h 0x84h ADC_ALC_4 0x0Ah 0x85h ADC_ALC_5 0x0Ah 0x86h ADC_ALC_6 0x0Ah 0x87h ADC_ALC_7 0x1Fh 0x89h ADC_L_LEVEL 0x33h 0x8Ah ADC_R_LEVEL 0x33h 0xA3h DAC_ALC_4 0x0Ah 0xA4h DAC_ALC_5 0x0Ah 0xA5h DAC_ALC_6 0x0Ah 0xA6h DAC_ALC_7 0x33h Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 31 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 2. Nonzero I2C Default Registers (continued) Address Register Default Data Value 0xA8h DAC_L_LEVEL 0x33h 0xA9h DAC_R_LEVEL 0x33h 0xF0h RESET 0x02h Basic PMC Setup Register This register is used to control the LM49352's Basic Power Management Setup: Table 3. PMC_SETUP (0x00h) Bits Field Description When this bit is set the power management will enable the MCLK I/O or internal oscillator (1). It will then use this clock to sequence the enabling of the analog references and bias points. When this bit is cleared the PMC will bring the analog down gently and disable the MCLK or oscillator. 0 CHIP_ENABLE CHIP _ENABLE Chip Status 0 Turn Chip Off 1 Turn Chip On This enables the PLL. 1 PLL_ENB PLL_ENABLE PLL Status 0 PLL Off 1 PLL On This enables the P2 output of the PLL. 2 PLL_P2ENB PLL_P2ENB PLL P2 Status 0 PLL P2 Off 1 PLL P2 On This enables the internal 300kHz Oscillator. For analog only chip modes, the oscillator can be used instead of an external system clock to drive the chip's power management (PMC). 3 4 OSC_ENB MCLK_OVR OSC_ENABLE Oscillator Status 0 Oscillator Off 1 Oscillator On This forces the MCLK input to enable, regardless of requirement. If set, the audio ports and digital mixer can be activated even if the chip is in shutdown mode. This assumes that MCLK is selected as the PMC clock source (reg 0x01h) and that there is an active clock signal driving the MCLK pin. Setting this bit reduces power consumption, by allowing audio ports and digital mixer to operate while the analog sections of the chip are powered down. MCLK_OVR Comment 0 I/O control is automatic 1 MCLK input forced on. This forces the clock input of Audio Port 1 input to enable, regardless of other port settings. 5 PORT1_CLK_OVR PORT1_CLK_OVR Comment 0 I/O control is automatic 1 PORT_CLK input forced on This forces the clock input of Audio Port 2 input to enable, regardless of other port settings. (1) 32 6 PORT2_CLK_OVR 7 CHIP_ACTIVE PORT2_CLK_OVR Comment 0 I/O control is automatic 1 PORT_CLK input forced on This bit is used to readback the enable status of the chip. If the PMC is set to operate from one of the audio ports then it will wait for the port to be enabled or the relevant override bit to be set, forcing the port clock input to enable. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 PMC Clocks Register This register is used to control the LM49352's Basic Power Management Clock: Table 4. PMC_SETUP (0x01h) Bits Field 1:0 PMC_CLK_SEL Description This selects the source of the PMC input clock. PMC_CLK_SEL PMC Input Clock Source 00 MCLK (Default divide is 40.5) 01 Internal 300kHz Oscillator 10 DAC SOURCE CLOCK 11 ADC SOURCE CLOCK PMC Clock Divide Register This register is used to control the LM49352's Power Management Circuit Clock Divider: Table 5. PMC_SETUP (0x02h) Bits Field 7:0 PMC_CLK_DIV Description This programs the half cycle divider that precedes the PMC. The PMC should run from a 300kHz clock. The default of this divider is 0x50h (divide by 40.5) to get a 300kHz PMC clock from a 12MHz or 12.288MHz MCLK. Program this divider with the required division, multiplied by 2, and subtract 1. PMC_CLK_DIV Divide by 00000000 1 00000001 1 00000010 1.5 00000011 2 00000100 2.5 00000101 3 -- -- 11111101 126 11111110 127.5 11111111 128 LM49352 Clock Network (Refer to Figure 57) The audio DAC and ADC operate at a clock frequency of 2*OSR*fS where OSR is the oversampling ratio and fS is the sampling frequency of the DAC or ADC. The DAC can operate at three different OSR settings (128, 125, 64). The ADC can operate at two different OSR settings (128, 125). For example, if the stereo DAC or ADC is set at OSR = 128, a 12.288MHz clock is required for 48kHz data. If a 12.288MHz clock is not available, then the internal PLL can be used to generate the desired clock frequency. Otherwise, if a 12.288MHz is available, the PLL can be bypassed to reduce power consumption. The DAC clock divider or ADC clock divider can also be used to generate the correct clock. If an 18.432 MHz clock is available, the DAC or ADC clock divider could be set to 1.5 in order to generate a 12.288MHz clock from 18.432MHz without using a PLL. The DAC path clock (DAC_SOURCE_CLK) and ADC path clock (ADC_SOURCE_CLK) can be driven directly by the MCLK input, the PORT1_CLK input, the PORT2_CLK input, or PLL output. For instances where a PLL must be used, the PLL input clock can come from three sources. The clock input to the PLL can come from the MCLK input, the PORT1_CLK input, or the PORT2_CLK input. The LM49352's Power Management Circuit (PMC) requires a clock that is independent from the DAC or ADC. It is recommended to provide a 300kHz clock at Point C. The PMC clock divider is available to generate the correct clock to the PMC block. The PMC clock path can be driven directly by the MCLK input, the internal 300kHz oscillator, the DAC_SOURCE_CLK, or the ADC_SOURCE_CLK. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 33 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 6. DAC Clock Requirements DAC Sample Rate (kHz) Clock Required at A (OSR = 128) Clock Required at A (OSR = 125) Clock Required at A (OSR = 64) Clock Required at A (OSR = 32) 8 2.048 MHz 2 MHz 1.024 MHz 0.512 MHz 11.025 2.8224 MHz 2.75625 MHz 1.4112 MHz 0.7056 MHz 12 3.072 MHz 3 MHz 1.536 MHz 0.768 MHz 16 4.096 MHz 4 MHz 2.048 MHz 1.024 MHz 22.05 5.6448 MHz 5.5125 MHz 2.8224 MHz 1.4112 MHz 24 6.144 MHz 6 MHz 3.072 MHz 1.536 MHz 32 8.192 MHz 8 MHz 4.096 MHz 2.048MHz 44.1 11.2896 MHz 11.025 MHz 5.6448 MHz 2.8224 MHz 48 12.288 MHz 12 MHz 6.144 MHz 3.072 MHz 96 24.576 MHz 24 MHz 12.288 MHz 6.144 MHz Table 7. ADC Clock Requirements ADC Sample Rate (kHz) Clock Required at B (OSR = 128) Clock Required at B (OSR = 125) 8 2.048 MHz 2 MHz 11.025 2.8224 MHz 2.75625 MHz 12 3.072 MHz 3 MHz 16 4.096 MHz 4 MHz 22.05 5.6448 MHz 5.5125 MHz 24 6.144 MHz 6 MHz 32 8.192 MHz 8 MHz 44.1 11.2896 MHz 11.025 MHz 48 12.288 MHz 12 MHz INTERNAL OSCILLATOR 300 kHz % PMC C PMC A % DAC Stereo DAC 1 25 MHz 0 _> 50 MHz PLL MCLK 0 _ 50 MHz % ADC AUDIO PORT 1 PORT1_CLK 0 _ 50 MHz AUDIO PORT 2 PORT2_CLK MIXER Stereo ADC B % 1/2 Cycle PMC, DAC, ADC divides by 1, 1.5, 2, 2.5 ==> 128 % 1/2 Cycle Half Cycle divides by 1, 1.5, 2, 2.5 ==> 32 Figure 57. Internal Clock Network 34 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 PLL Setup Registers PLL_P1 1 25 MHz % P1 9 P1 = 1,1.5, 2 _> 256 M = 1, 1.5, 2 _> 64 0.5 - 50 MHz Phase Comparator and Charge Pump 9 I %M VCO PLL_P2 140 to 210 MHz 1 25 MHz % P2 P2 = 1,1.5, 2 _> 256 0.7 < 5 MHz 7 %N N = 10, 11, 12 _> 250 PLL_M 6'M 8 8 5 PLL_N PLL_N_MOD Figure 58. PLL Loop The LM49352 contains a PLL for flexible operation of its dual audio ports. The PLL has a P1 and P2 output divider thereby allowing the PLL to generate two distinct clock outputs. The equations for the PLL's generated output clocks are as follows: fOUT1 = (fIN . N / M . P1) fOUT2 = (fIN . N / M . P2) where: N = PLL_N + PLL_N_MOD M = (PLL_M + 1) / 2 P1 = (PLL_P1 + 1) / 2 P2 = (PLL_P2 + 1) / 2 The VCO frequency and comparison frequencies are as follows: fVCO = fOUT.P fCOMP = fIN/M Keep fVCO between 140MHz to 240MHz and keep fCOMP between 700KHz to 5MHz. Table 8. PLL Settings for Common System Clock Frequencies fIN (MHz) M N N_MOD P fOUT (Hz) 12 2.5 32 0 12.5 12288000 Error (Hz) 0 13 15.5 175 26 12 12287970 -30 14.4 12.5 128 0 12 12288000 0 16.2 13.5 128 0 12.5 12288000 0 16.8 3.5 32 0 12.5 12288000 0 19.2 12.5 96 0 12 12288000 0 19.68 20.5 160 0 12.5 12288000 0 19.8 16.5 128 0 12.5 12288000 0 26 32.5 192 0 12.5 12288000 0 27 22.5 128 0 12.5 12288000 0 12 12.5 147 0 12.5 11289600 0 12.288 10 147 0 16 11289600 0 13 9 144 19 18.5 11289603 +3 14.4 12.5 147 0 15 11289600 0 16.2 22.5 196 0 12.5 11289600 0 16.8 12.5 126 0 15 11289600 0 19.2 20 147 0 12.5 11289600 0 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 35 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 8. PLL Settings for Common System Clock Frequencies (continued) fIN (MHz) M N N_MOD P fOUT (Hz) Error (Hz) 19.68 20.5 147 0 12.5 11289600 0 19.8 27.5 196 0 12.5 11289600 0 26 18.5 144 19 18 11289602.1 2.1 27 37.5 196 0 12.5 12289600 0 11.2896 10.5 195 0 17.5 12000000 0 12.288 8 125 0 16 12000000 0 13 6.5 102 0 17 12000000 0 13.5 4.5 68 0 17 12000000 0 14.4 6 85 0 17 12000000 0 16.2 13.5 170 0 17 12000000 0 16.8 7 85 0 17 12000000 0 19.2 8 85 0 17 12000000 0 19.68 20.5 200 0 16 12000000 0 19.8 16.5 170 0 17 12000000 0 26 6.5 36 0 12 12000000 0 11.2896 8 125 0 16 11025000 0 12 10 147 0 16 11025000 0 12.288 8 114 27 16 11025000 0 13 6.5 96 15 17.5 11025000 0 13.5 10 147 0 18 11025000 0 14.4 4 49 0 16 11025000 0 16.2 4 49 0 18 11025000 0 16.8 16 189 0 18 11025000 0 19.2 16 147 0 16 11025000 0 19.68 16 189 0 18 11025000 0 19.8 16 147 0 16.5 11025000 0 26 5 27 18 13 1102500 0 Table 9. PLL_CLOCK_SOURCE (0x03h) 36 Bits Field 1:0 PLL_CLK_SEL Description This selects the source of the input clock to the PLL. PLL_CLK_SEL PLL Input Clock Source 00 MCLK 01 PORT1_CLK 10 PORT2_CLK 11 RESERVED Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 10. PLL_M (0x04h) Bits Field 6:0 PLL_M Description This programs the PLL's M divider to divide from 1 to 64. PLL_M PLL Input Divider Value 000000 1 000001 1 000010 1.5 000011 2 000100 2.5 000101 3 -- -- 1111101 63 1111110 63.5 1111111 64 Table 11. PLL_N (0x05h) Bits Field 7:0 PLL_N Description This programs the PLL N divider to divide from 1 to 250. PLL_N Feedback Divider Value 00000000 to 00001010 10 00001011 11 00001100 12 00001101 13 00001110 14 00001111 15 -- -- 11111000 248 11111001 249 11111010 to 11111111 250 Table 12. PLL_N_MOD (0x06h) Bits Field 4:0 PLL_N_MOD Description This programs the sigma-delta modulator in the PLL. PLL_N_MOD Fractional Part of N 00000 0 00001 1/32 00010 2/32 00011 3/32 00100 4/32 00101 5/32 -- -- 11101 20/32 11110 30/32 11111 31/32 5 PLL_P1[8] This sets the MSB of the 1st P Divider on the PLL which is part of a standard half-cycle divider control. 6 PLL_P2[8] This sets the MSB of the 2nd P Divider on PLL which is part of a standard half-cycle divider control. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 37 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 13. PLL_P1 (0x07h) Bits Field Description 7:0 PLL_P1[7:0] This programs the 8 LSBs of the PLL's P1 Divider. These LSBs combine with PL1_P1[8] which allows the P1 divider to divide by up to 256. PLL_P1 [8:0] P1 Divider Value 000000000 1 000000001 1 000000010 1.5 000000011 2 000000100 2.5 000000101 3 -- -- 111111101 255 111111110 255.5 111111111 256 Table 14. PLL_P2 (0x08h) Bits Field Description 7:0 PLL_P2[7:0] This programs 8 LSBs of the PLL's P2 Divider. These LSBs combine with PLL_P2[8] which allows the P2 divider to divide by up to 256. PLL_P2 [8:0] P2 Divider Value 000000000 1 000000001 1 000000010 1.5 000000011 2 000000100 2.5 000000101 3 -- -- 111111101 255 111111110 255.5 111111111 256 Analog Mixer Control Registers This register is used to control the LM49352's Analog Mixer: Table 15. CLASS_D_OUTPUT (0x10h) 38 Bits Field Description 0 DACR_LS The right DAC output is added to the loudspeaker output. 1 DACL_LS The left DAC output is added to the loudspeaker output. 2 RSVD Reserved 3 RSVD Reserved 4 MONO_LS 5 AUX_LS The MONO input is added to the loudspeaker output. The AUX input is added to the loudspeaker output. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Class D Loudspeaker Amplifier The LM49352 features a filterless modulation scheme. The differential outputs of the device switch at 300kHz from VDD to GND. When there is no input signal applied, the two outputs (LS+ and LS-) switch with a 50% duty cycle, with both outputs in phase. Because the outputs of the LM49352 are differential, the two signals cancel each other. This results in no net voltage across the speaker, thus there is no load current during an idle state, conserving power. With an input signal applied, the duty cycle (pulse width) of the LM49352 outputs changes. For increasing output voltages, the duty cycle of LS+ increases, while the duty cycle of LS- decreases. For decreasing output voltages, the converse occurs, the duty cycle of LS- increases while the duty cycle of LS+ decreases. The difference between the two pulse widths yields the differential output voltage. Spread Spectrum Modulation The LM49352 features a fitlerless spread spectrum modulation scheme that eliminates the need for output filters, ferrite beads or chokes. The switching frequency varies by 30% about a 300kHz center frequency, reducing the wideband spectral content, improving EMI emissions radiated by the speaker and associated cables and traces. Where a fixed frequency class D exhibits large amounts of spectral energy at multiples of the switching frequency, the spread spectrum architecture of the LM49352 spreads that energy over a larger bandwidth. The cycle-to-cycle variation of the switching period does not affect the audio reproduction or efficiency. Class D Power Dissipation and Efficiency In general terms, efficiency is considered to be the ratio of useful work output divided by the total energy required to produce it with the difference being the power dissipated, typically, in the IC. The key here is "useful" work. For audio systems, the energy delivered in the audible bands is considered useful including the distortion products of the input signal. Sub-sonic (DC) and super-sonic components (>22kHz) are not useful. The difference between the power flowing from the power supply and the audio band power being transduced is dissipated in the LM49352 and in the transducer load. The amount of power dissipation in the LM49352's class D amplifier is very low. This is because the ON resistance of the switches used to form the output waveforms is typically less than 0.25. This leaves only the transducer load as a potential "sink" for the small excess of input power over audio band output power. The LM49352 dissipates only a fraction of the excess power requiring no additional PCB area or copper plane to act as a heat sink. EMI/RFI Filtering If system level PCB layout constraints require the LM49352's Class D output bumps to be placed far away from the speaker or the Class D output traces to be routed near EMI/RFI sensitive components, an external EMI/RFI filter should be used. A series ferrite bead placed close to the Class D output bumps along with a shunt capacitor to ground placed close to the ferrite bead will reduce the EMI/RFI emissions of the Class D amplifier's switching outputs. The ferrite bead must be rated with a current rating high enough to properly drive the loudspeaker. The ferrite bead that is rated for 1A or greater is recommended. The DC resistance of the ferrite bead is another important specification that must be taken into consideration. A low DC resistance will minimize any power losses dissipated by the EMI/RFI filter thereby preserving the power efficiency advantages of the Class D amplifier. Selecting a ferrite bead with high DC resistance will decrease output power delivered to speaker and reduce the Class D amplifier's efficiency. The shunt capacitor needs to have low ESR. A 10pF ceramic capacitor with a X7R dielectric is recommended as a starting point. Care needs to be taken to ensure that the value of the shunt capacitor does not exceed 47pF when using a low resistance ferrite bead in order to prevent permanent damage to the low side FETs of the Class D output stage. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 39 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com LS+ Ferrite Bead LM49352 Class D 10 pF Speaker LSFerrite Bead 10 pF LSGND Figure 59. EMI/RFI Filter for the Class D Amplifier Table 16. LEFT HEADPHONE_OUTPUT (0x11h) Bits Field Description 0 DACR_HPL The right DAC output is added to the left headphone output. 1 DACL_HPL The left DAC output is added to the left headphone output. 2 RSVD Reserved 3 RSVD Reserved 4 MONO_HPL 5 AUX_HPL The MONO input is added to the left headphone output. The AUX input is added to the left headphone output. Table 17. RIGHT HEADPHONE_OUTPUT (0x12h) Bits Field Description 0 DACR_HPR The right DAC output is added to the right headphone output. 1 DACL_HPR The left DAC output is added to the right headphone output. 2 RSVD Reserved 3 RSVD Reserved 4 MONO_HPR 5 AUX _HPR The MONO input is added to the right headphone output. The AUX input is added to the right headphone output. Headphone Amplifier Function The LM49352 headphone amplifier features TI's ground referenced architecture that eliminates the large DCblocking capacitors required at the outputs of traditional headphone amplifiers. A low-noise inverting charge pump creates a negative supply (HP_VSS) from the positive supply voltage (LS_VDD). The headphone amplifiers operate from these bipolar supplies, with the amplifier outputs biased about GND, instead of a nominal DC voltage (typically VDD/2), like traditional amplifiers. Because there is no DC component to the headphone output signals, the large DC-blocking capacitors (typically 220F) are not necessary, conserving board space and system cost, while improving frequency response. Charge Pump Capacitor Selection Use low ESR ceramic capacitors (less than 100m) for optimum performance. Charge Pump Flying Capacitor (C6) The flying capacitor (C6) affects the load regulation and output impedance of the charge pump. A C6 value that is too low results in a loss of current drive, leading to a loss of amplifier headroom. A higher valued C6 improves load regulation and lowers charge pump output impedance to an extent. Above 2.2F, the RDS(ON) of the charge pump switches and the ESR of C6 and C5 dominate the output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. Please refer to the demonstration board schematic shown in Figure 72. 40 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Charge Pump Flying Capacitor (C5) The value and ESR of the hold capacitor (C5) directly affects the ripple on CPVSS. Increasing the value of C5 reduces output ripple. Decreasing the ESR of C5 reduces both output ripple and charge pump output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. Please refer to the demonstration board schematic shown in Figure 72. Table 18. AUX_OUTPUT (0x13h) Bits Field 0 DACR_AUX The right DAC output is added to the AUX output. 1 DACL_AUX The left DAC output is added to the AUX output. 2 MIC_AUX 3 RSVD 4 MONO_AUX 5 AUX_AUX Description The MIC input is added to the AUX output. Reserved The MONO input is added to the AUX output. The AUX input is added to the AUX output. Auxiliary Output Amplifier The LM49352's auxiliary output (AUXOUT) amplifier provides differential drive capability to loads that are connected across its outputs. This results in output signals at the AUX_OUT+ and AUX_OUT- pins that are 180 degrees out of phase with respect to each other. This effectively doubles the maximum possible output swing for a specific supply voltage when compared to single-ended output configurations. The differential output configuration also allows the load to be isolated from ground since both the AUX_OUT+ and AUX_OUT- pins are biased at the same DC potential. This eliminates the need for any large and expensive DC blocking capacitors at the AUXOUT amplifier outputs. The load can then be directly connected to the positive and negative outputs of the AUXOUT amplifier which then isolates it from any ground noise, thereby improving signal to noise ratio (SNR) and power supply rejection ratio (PSRR). The AUXOUT amplifier has two modes of operation. The primary mode of operation is high current drive mode (Earpiece Mode) where the AUXOUT amplifier can be used to differentially drive a mono earpiece speaker. The secondary mode of operation is low current drive mode where the AUXOUT amplifier operates in a power saving mode (AUX_LINE_OUT Mode) to provide a differential output that is used as a mono differential line level input to a standalone mono differential input class D amplifier (LM4675) for stereo loudspeaker applications. Table 19. OUTPUT_OPTIONS (0x14h) Bits Field 0 RSVD Description Reserved This sets the gain of the left and right headphone amplifiers. The gain of the left and right headphone amplifiers are always set to the same level. LR_HP_LEVEL 3:1 LR_HP_LEVEL Gain (dB) 000 0 001 -1.5 010 -3 011 -6 100 -9 101 -12 110 -15 111 -18 This sets the gain of the Auxiliary output amplifier. 4 AUX_NEG_6dB AUX_NEG_6dB Gain (dB) 0 0 1 -6 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 41 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 19. OUTPUT_OPTIONS (0x14h) (continued) Bits Field Description This sets the Auxiliary output amplifier mode of operation. 5 AUX_LINE_OUT AUX_LINE_OUT Auxiliary Output Mode 0 Earpiece Amplifier 1 AUX_LINE_OUT This sets the gain of the Class D loudspeaker amplifier. 7:6 LS_LEVEL LS_LEVEL Gain (dB) 00 0 01 4 10 8 11 12 Table 20. ADC_INPUT (0x15h) Bits Field Description 0 DACR_ADCR The right DAC output is added to the ADC right input. 1 DACL_ADCL The left DAC output is added to the ADC left input. 2 MIC_ADCR The MIC input is added to the ADC right input. 3 MIC_ADCL The MIC input is added to the ADC left input. 4 AUX_ADCR The AUX input is added to the ADC right input. 5 MONO_ADCL The MONO input is added to the ADC left input. Table 21. MIC_INPUT (0x16h) 42 Bits Field 3:0 MIC_LEVEL 4 SE_DIFF 5 MUTE Description This sets the gain of the microphone preamp. MIC_LEVEL Gain 0000 6dB 0001 8dB 0010 10dB 0011 12dB 0100 14dB 0101 16dB 0110 18dB 0111 20dB 1000 22dB 1001 24dB 1010 26dB 1011 28dB 1100 30dB 1101 32dB 1110 34dB 1111 36dB If set, the MIC negative input is ignored. In single-ended mode, the MIC negative input pin should left floating. If set, the microphone preamp is muted. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 22. AUX_LEVEL (0x18h) Bits Field 5:0 AUX_LEVEL 6 SE/DIFF Description This programs the AUX input level. All gain changes are performed at zero crossings. AUX_LEVEL Level AUX_LEVEL Level 000000 -46.5dB 100000 1.5dB 000001 -45dB 100001 3dB 000010 -43.5dB 100010 4.5dB 000011 -42dB 100011 6dB 000100 -40.5dB 100100 7.5dB 000101 -39dB 100101 9dB 000110 -37.5dB 100110 10.5dB 000111 -36dB 100111 12dB 001000 -34.5dB 101000 13.5dB 001001 -33dB 101001 15dB 001010 -31.5dB 101010 16.5dB 001011 -30dB 101011 18dB 001100 -28.5dB 001101 -27dB 001110 -25.5dB 001111 -24dB 010000 -22.5dB 010001 -21dB 010010 -19.5dB 010011 -18dB 010100 -16.5dB 010101 -15dB 010110 -13.5dB 010111 -12dB 011000 -10.5dB 011000 -9dB 011001 -7.5dB 011010 -6dB 011100 -4.5dB 011101 -3dB 011110 -1.5dB 011111 0dB If set, the AUXL input is ignored. In single-ended mode, the AUXL input pin should be left floating. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 43 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 23. MONO_LEVEL (0x19h) Bits Field 5:0 MONO_LEVEL 6 SE/DIFF 7 AUXL_MONO Description This programs the MONO input level. All gain changes are performed at zero crossings. MONO_LEVEL Level MONO_LEVEL Level 000000 -46.5dB 100000 1.5dB 000001 -45dB 100001 3dB 000010 -43.5dB 100010 4.5dB 000011 -42dB 100011 6dB 000100 -40.5dB 100100 7.5dB 000101 -39dB 100101 9dB 000110 -37.5dB 100110 10.5dB 000111 -36dB 100111 12dB 001000 -34.5dB 101000 13.5dB 001001 -33dB 101001 15dB 001010 -31.5dB 101010 16.5dB 001011 -30dB 101011 18dB 001100 -28.5dB 001101 -27dB 001110 -25.5dB 001111 -24dB 010000 -22.5dB 010001 -21dB 010010 -19.5dB 010011 -18dB 010100 -16.5dB 010101 -15dB 010110 -13.5dB 010111 -12dB 011000 -10.5dB 011000 -9dB 011001 -7.5dB 011010 -6dB 011100 -4.5dB 011101 -3dB 011110 -1.5dB 011111 0dB If set, the MONO- input is ignored. In single-ended mode, the MONO- input pin should be left floating. If set, AUXL is routed to the MONO Input Amplifier. Headphone Detection Circuit The LM49352 features a headphone detection circuit (HDC) that automatically enables the headphone amplifier whenever the insertion of a headphone plug is detected and disables the headphone amplifier during the removal of a headphone plug. The HDC optimizes power management by automatically disabling any output amplifier that is not in use. The HDC eliminates the necessity of polling the I2C bus for status changes. However, since the HDC requires the use of the GPIO pin, the PORT2_SDO functionality sensing is required. The HDC requires a headphone jack with a normally closed mechanical switch and a pullup resistor, RPU, tied between the mechanical switch and I/O_VDD (Refer to Figure 60). Choosing a RPU value of at least 500k ensures minimal current draw through the pullup resistor. When the headphone amplifier is disabled, an internal 50k pulldown, RPD, is connected to each headphone amplifier output. Without the presence of a headphone plug, the headphone jack's mechanical switch is closed thereby connecting the right headphone amplifier output 44 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 to RPU. The GPIO pin detects a logic low level due to the voltage division between RPU and RPD. When the GPIO pin is set to HPSENSE mode, a logic low voltage reading causes the HDC to disable the headphone amplifier. When a headphone plug is inserted, the mechanical connection between RPU and RPD is broken, resulting in a logic high level detected by the GPIO pin. A logic high voltage reading causes the HDC to enable the headphone amplifier. The HDC has four modes of operation that automatically enable/disable different combinations of the audio output amplifiers contained within the LM49352. Having the choice of four different HDC settings maximizes power management flexibility to suit a particular application. Please refer to the HP_SENSE (reg 0x1Bh) register table for a detailed discussion on the different HDC modes of operation. I/OVDD RPU 500 k: GPIO HPR RPD 50 k: Headphone Jack with a Normally Closed (NC) Mechanical Switch LM49352 HPL RPD 50 k: Figure 60. Application Circuit for Headphone Detection Table 24. HP_SENSE (0x1Bh) Bits Field Description 0 HP SENSE This bit enables the headphone sense circuit. If enabled, the headphone amplifier will automatically turn on/off based on the logic level of the GPIO pin whenever GPIO is selected as a headphone sense input. If the presence of a headphone insertion is detected, the headphone amplifier will automatically turn on. If a headphone removal is detected the headphone amplifier will automatically turn off. 1 2 HPSENSE_D HPSENSE_AUX HPSENSE Headphone Sense Status 0 Off 1 On This bit enables the headphone sense circuit. If enabled, the headphone amplifier will automatically turn on/off based on the logic level of the GPIO pin whenever GPIO is selected as a headphone sense input. If the presence of a headphone insertion is detected, the headphone amplifier will automatically turn on and the Class D loudspeaker amplifier will turn off. If a headphone removal is detected the headphone amplifier will automatically turn off and the Class D loudspeaker amplifier will turn on. This bit overrides bit 0 of this register. HPSENSE_D Headphone Sense Status 0 Off 1 On This bit enables the headphone sense circuit. If enabled, the headphone amplifier will automatically turn on/off based on the logic level of the GPIO pin whenever GPIO is selected as a headphone sense input. If the presence of a headphone insertion is detected, the headphone amplifier will automatically turn on and the Earpiece / Auxout amplifier will turn off. If a headphone removal is detected the headphone amplifier will automatically turn off and the Earpiece / Auxout amplifier will turn on. This bit overrides bit 0 and bit 1 of this register. HPSENSE_AUX Headphone Sense Status 0 Off 1 On Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 45 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 24. HP_SENSE (0x1Bh) (continued) Bits Field Description 3 HPSENSE_AUX_D This bit enables the headphone sense circuit. If enabled, the headphone amplifier will automatically turn on/off based on the logic level of the GPIO pin whenever GPIO is selected as a headphone sense input. If the presence of a headphone insertion is detected, the headphone amplifier will automatically turn on and the Class D loudspeaker amplifier along with the Earpiece / Auxout amplifier will turn off. If a headphone removal is detected the headphone amplifier will automatically turn off and the Class D loudspeaker amplifier along with the Earpiece / Auxout amplifier will turn on. This bit overrides bit 0, bit 1, and bit 2 of this register. HPSENSE_AUX_D Headphone Sense Status 0 Off 1 On ADC Control Registers This register is used to control the LM49352's ADC: Table 25. ADC Basic (0x20h) Bits Field 0 MONO Description This sets mono or stereo operation of the ADC. MONO 1 Stereo Audio 1 Mono Voice (Right ADC channel disabled, Left ADC channel active) This sets the oversampling ratio of the ADC. OSR Stereo Audio ADC Oversampling Ratio Mono Voice ADC Oversampling Ratio 0 128 125 1 128 128 2 MUTE_L If set, a digital mute is applied to the Left (or mono) ADC output. 3 MUTE_R If set, a digital mute is applied to the Right ADC output. 6:4 ADC_CLK_SEL 7 46 OSR ADC Operation 0 ADC_DSP_ONLY This selects the source of the ADC clock domain, ADC_SOURCE_CLK. ADC_CLK_SEL Source 000 MCLK 001 PORT1_RX_CLK 010 PORT2_RX_CLK 011 PLL_OUTPUT1 100 PLL_OUTPUT2 If set, the ADC's analog circuitry is disabled to reduce power consumption, however, ADC DSP functionality is maintained. This can be used to perform asynchronous resampling between audio rates of a common family. Setting this bit is also useful whenever applying Automatic Level Control (ALC) to an analog only audio path. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 26. ADC_CLK_DIV (0x21h) Bits Field Description 7:0 ADC_CLK_DIV This programs the half cycle divider that preceeds the ADC. The input of this divider should be around 12MHz. The default of this divider is 0x00. Program this divider with the division you want, multiplied by 2, and subtract 1. ADC_CLK_DIV Divides by 00000000 1 00000001 1 00000010 1.5 00000011 2 -- -- 11111101 127 11111110 127.5 11111111 128 Table 27. ADC_MIXER (0x23h) Bits Field 1:0 ADC_MIX_LEVEL_L Description This sets the input level to the left ADC channel. ADC_MIX_LEVEL_L 3.2 4 ADC_MIX_LEVEL_R STEREO_LINK Level 00 0dB 01 1.35dB 10 3.5dB 11 6dB This sets the input level to the right ADC channel. ADC_MIX_LEVEL_R Level 00 0dB 01 1.35dB 10 3.5dB 11 6dB If set, this links ADC_MIX_LEVEL_R with ADC_MIX_LEVEL_L. STEREO_LINK Status 0 Off 1 On DAC Control Registers This register is used to control the LM49352's DAC: Table 28. DAC Basic (0x30h) Bits Field 1:0 MODE Description This programs the over sampling ratio of the stereo DAC. MODE DAC Oversampling Ratio 00 125 01 128 10 64 (Default) 11 RSVD 2 MUTE_L This digitally mutes the Left DAC output. 3 MUTE_R This digitally mutes the Right DAC output. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 47 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 28. DAC Basic (0x30h) (continued) Bits Field 6:4 DAC_CLK_SEL Description This selects the source of the DAC clock domain, DAC_SOURCE_CLK. DAC_CLK_SEL 7 DSP_ONLY Source 000 MCLK 001 PORT1_RX_CLK 010 PORT2_RX_CLK 011 PLL_OUTPUT1 100 PLL_OUTPUT2 If set, the DAC's analog circuitry is disabled to reduce power consumption, however DAC DSP functionality is maintained. This can be used to perform asyncronous resampling between audio rates of a common family. Table 29. DAC_CLK_DIV (0x31h) Bits Field Description 7:0 DAC_CLK_DIV This programs the half cycle divider that precedes the DAC. The input of this divider should be around 12MHz. The default of this divider is 0x03 which gives a division by 2. Program this divider with the division you want, multiplied by 2, and subtract 1. DAC_CLK_DIV Divides by 00000000 1 00000001 1 00000010 1.5 00000011 2 (Default) -- -- 11111101 127 11111110 127.5 11111111 128 Digital Mixer Control Registers Digital Mixer The LM49352's digital mixer allows for flexible routing of digital audio signals between both audio ports, DAC, and ADC. This mixer handles which digital data path (Port1 RX data, Port2 RX data, or ADC output) is routed to the DAC input. The digital mixer also selects the appropriate digital data path (Port1 RX data, Port2 RX data, ADC output, or DAC DSP (Interpolator) output) that is used for data transmission on Audio Port 1 and 2. Audio inputs to the digital mixer can be attenuated down to -18dB to avoid clipping conditions. The digital mixer also allows direct routing from the DAC interpolator output to the ADC decimator input which allows the DAC and ADC DSP blocks to be cascaded witjhout having to enable the analog of the DAC and ADC in order to save power. Another key feature of the digital mixer is sample rate conversion (SRC) between audio ports. This allows simultaneous operation of the dual audio ports even if each port is operating at a different sample rate. The LM49352 can be used as an audio port bridge with SRC capability. The digital mixer allows either straight pass through between audio ports or, if desired, DSP effects can be added to the digital audio signal during audio port bridge operation. The digital mixer automatically handles stereo I2S to mono PCM conversion between audio ports and vice versa. 48 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Figure 61. Digital Mixer The LM49352 includes two separate and independent DSP blocks, one for the DAC and the other for the ADC. The digital mixer also allows both DSP blocks to be cascaded together in either order so that the DSP effects from both blocks can be combined into the same signal path. For example, the 5 band parametric EQ of each DSP block can be combined together to form a 10 band parametric EQ for added flexibility. This register is used to control the LM49352's digital mixer: Table 30. Input Levels 1 (0x40h) Bits Field 1:0 PORT1_RX_L _LVL Description This programs the input level of the data arriving from the left receive channel of Audio Port 1. PORT1_RX_L_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 49 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 30. Input Levels 1 (0x40h) (continued) Bits Field 3:2 PORT1_RX_R _LVL 5:4 7:6 PORT2_RX_L _LVL PORT2_RX_R _LVL Description This programs the input level of the data arriving from the right receive channel of Audio Port 1. PORT1_RX_R_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB This programs the input level of the data arriving from the left receive channel of Audio Port 2. PORT2_RX_L_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB This programs the input level of the data arriving from the right receive channel of Audio Port 2. PORT2_RX_R_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB Table 31. Input Levels 2 (0x41h) Bits Field 1:0 ADC_L_LVL Description This programs the input level of the data arriving from the left ADC channel. ADC_L_LVL 3:2 ADC_R_LVL 00 0dB 01 -6dB 10 -12dB 11 -18dB This programs the input level of the data arriving from the right ADC channel. ADC_R_LVL 5:4 7:6 INTERP_L_LVL INTERP_R_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB This programs the input level of the data arriving from the left DAC's interpolator output. INTERP_L_LVL Level 00 0dB 01 -6dB 10 -12dB 11 -18dB This programs the input level of the data arriving from the right DAC's interpolator output. INTERP_R_LVL 50 Level Level 00 0dB 01 -6dB 10 -12dB 11 -18dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 32. Audio Port 1 Input (0x42h) Bits Field 1:0 L_SEL Description This selects which input is fed to the Left TX Channel of Audio Port 1. L_SEL 3:2 R_SEL Selected Input 00 None 01 ADC_L 10 PORT2_RX_L 11 DAC_INTERP_L This selects which input is fed to the Right TX Channel of Audio Port 1. R_SEL Selected Input 00 None 01 ADC_R 10 PORT2_RX_R 11 DAC_INTERP_R 4 SWAP If set, this swaps the Left and Right outputs to Audio Port 1. 5 MONO If set, the right channel is ignored and the left channel becomes (left+right)/2. Bits Field 1:0 L_SEL Table 33. Audio Port 2 Input (0x43h) 3:2 R_SEL Description This selects which input is fed to Audio Port 2's Left TX Channel. L_SEL Selected Input 00 None 01 ADC_L 10 PORT1_RX_L 11 DAC_INTERP_L This selects which input is fed to Audio Port 2's Right TX Channel. R_SEL Selected Input 00 None 01 ADC_R 10 PORT1_RX_R 11 DAC_INTERP_R 4 SWAP If set, this swaps the Left and Right outputs to Audio Port 2. 5 MONO If set, the right channel is ignored and the left channel becomes (left+right)/2. Table 34. DAC Input Select (0x44h) Bits Field 0 PORT1_L This adds Audio Port 1's left RX channel to the DAC's left input. Description 1 PORT2_L This adds Audio Port 2's left RX channel to the DAC's left input. 2 ADC_L 3 PORT1_R This adds Audio Port 1's right RX channel to the DAC's right input. 4 PORT2_R This adds Audio Port 2's right RX channel to the DAC's right input. 5 ADC_R This adds the ADC's right output to the DAC's right input. 6 SWAP If set, this swaps the Left and Right inputs to the DAC. This adds the ADC's left output to the DAC's left input. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 51 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 35. Decimator Input Select (0x45h) Bits Field 1:0 L_SEL Description This selects which input is fed to the left ADC's decimator input. L_SEL 3:2 R_SEL Selected Input 00 None 01 PORT1_RX_L 10 PORT2_RX_L 11 DAC_INTERP_L This selects which input is fed to the right ADC's decimator input. R_SEL 5:4 MXR_CLK_SEL Selected Input 00 None 01 PORT1_RX_R 10 PORT2_RX_R 11 DAC_INTERP_R This selects sets the source of the Digital Mixer Clock. The 'Auto' setting will automatically select the source with the highest clock frequency. If the DAC interpolator output (DAC_OSR_L or DAC_OSR_R) is selected, then MXR_CLK_SEL should be set to '10'. MXR_CLK_SEL Selected Input 00 Auto 01 MCLK 10 DAC 11 ADC Audio Port Control Registers I2S_CLK I2S_SYNC I2S_SDO/ I2S_SDI 23 22 21 2 1 0 23 22 21 Left Word 2 1 0 1 0 Right Word 2 Figure 62. I S Serial Data Format (24 bit example) I2S_CLK I2S_SYNC I2S_SDO/ I2S_SDI 23 22 21 20 2 1 0 23 22 21 Left Word 20 2 23 Right Word Figure 63. Left Justified Data Format (24 bit example) 52 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 I2S_CLK I2S_SYNC I2S_SDO/ I2S_SDI 0 23 22 21 3 2 1 0 23 22 21 Left Word 3 2 1 0 11 10 Right Word Figure 64. Right Justified Data Format (24 bit example) PCM_CLK PCM_SYNC PCM_SDO/ PCM_SDI 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 9 Short frame sync mode Long frame sync mode Figure 65. PCM Serial Data Format (16 bit example) The following registers are used to control the LM49352's audio ports. Audio Port 1 and Audio Port 2 are identical. Port 1 is programmed through the (0x5Xh) registers. Port 2 is programmed through the (0x6Xh) registers. Table 36. BASIC_SETUP (0x50h/0x60h) Bits Field 0 STEREO 1 RX_ENABLE If set, the input is enabled (enables the SDI port and input shift register and any clock generation required). 2 TX_ENABLE If set, the output is enabled (enables the SDO port and output shift register and any clock generation required). 3 CLOCK_MS If set, the audio port will transmit the clock when either the RX or TX is enabled. 4 SYNC_MS 5 CLOCK_PHASE 6 STEREO_SYNC_PHASE Description If set, the audio port will receive and transmit stereo data. If set, the audio port will transmit the sync signal when either the RX or TX is enabled. This sets how data is clocked by the Audio Port. CLOCK_PHASE Audio Data Mode 0 I2S (TX on falling edge, RX on rising edge) 1 PCM (TX on rising edge, RX on falling edge) If set, this reverses the left and right channel data of the Audio Port. STEREO_SYNC_PHASE Audio Port Data Orientation 0 Left channel data goes to left channel output. Right channel data goes to right channel output. 1 Right channel data goes to left channel output. Left channel data goes to right channel output. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 53 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 36. BASIC_SETUP (0x50h/0x60h) (continued) Bits Field 7 SYNC_INVERT Description If this bit is set the SYNC is inverted before the receiver and transmitter. SYNC_INVERT SYNC ORIENTATION 0 SYNC Low = Left, SYNC High = Right 1 SYNC Low = Right, SYNC High = Left Table 37. CLK_GEN_1 (0x51h/0x61h) Bits 5:0 6 Field Description HALF_CYCLE_CLK_DI This programs the half-cycle divider that generates the master clocks in the audio port. The default of V this divider is 0x00, i.e. bypassed. Program this divider with the required division multiplied by 2, and subtract 1. CLOCK_SEL HALF_CYCLE_CLK_DIV Divides By 000000 BYPASS 000001 1 000010 1.5 000011 2 -- -- 111101 31 111110 31.5 11111 32 This selects the clock source of the master mode Audio Port Clock generator's half-cycle divider. 0 = DAC_SOURCE_CLK 1 = ADC_SOURCE_CLK Table 38. CLK_GEN_1 (0x52h/62h) Bits Field Description 2:0 SYNTH_NUM Along with SYNTH_DENOM, this sets the clock divider that generates the Port 1 or Port 2 clock in master mode. 3 54 SYNTH_DENOM SYNTH_NUM Numerator 000 SYNTH_DENOM (1/1) 001 100/SYNTH_DENOM 010 96/SYNTH_DENOM 011 80/SYNTH_DENOM 100 72/SYNTH_DENOM 101 64/SYNTH_DENOM 110 48/SYNTH_DENOM 111 0/SYNTH_DENOM Along with SYNTH_NUM, this sets the clock divider that generates the Port 1 or Port 2 clock in master mode. SYNTH_DENOM Denominator 0 128 1 125 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 39. CLK_GEN_1 (0x53h/63h) Bits Field Description 2:0 SYNC_RATE This sets the number of clock cycles before the sync pattern repeats. This depends if the audio port data is mono or stereo. In MONO mode: SYNC_RATE Number of Clock Cycles 000 8 001 12 010 16 011 18 100 20 101 24 110 25 111 32 In STEREO mode: 5:3 SYNC_WIDTH SYNC_RATE Number of Clock Cycles 000 16 001 24 010 32 011 36 100 40 101 48 110 50 111 64 In MONO mode, this programs the width (in number of bits) of the SYNC signal. SYNC_WIDTH Width of SYNC (in bits) 000 1 001 2 010 4 011 7 100 8 101 11 110 15 111 16 Table 40. DATA_WIDTHS (0x54h/64h) Bits Field 2:0 RX_WIDTH Description This programs the expected bits per word of the serial data input SDI. RX_WIDTH Bits 000 24 001 20 010 18 011 16 100 14 101 13 110 12 111 8 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 55 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 40. DATA_WIDTHS (0x54h/64h) (continued) Bits Field 5:3 TX_WIDTH 7:6 TX_EXTRA_BITS Description This programs the bits per word of the serial data output SDO. TX_WIDTH Description 000 24 001 20 010 18 011 16 100 14 101 13 110 12 111 8 This programs the TX data output padding. TX_EXTRA_BITS Description 00 0 01 1 10 High-Z 11 High-Z Table 41. RX_MODE (0x55h/x65h) 56 Bits Field 0 RX_MODE Description This sets the RX data input justification with respect to the SYNC signal. RX_MODE Description 0 MSB Justified 1 LSB Justified Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 41. RX_MODE (0x55h/x65h) (continued) Bits Field 5:1 MSB_POSITION Description This specifies the bit location of the MSB from the start of the frame (MSB Justified) or from the end of the frame (LSB Justified). MSB_POSITION Description 00000 0(Left Justified/PCM Long) 00001 1(I2S/PCM Short) 00010 2 00011 3 00100 4 00101 5 00110 6 00111 7 01000 8 01001 9 01010 10 01011 11 01100 12 01101 13 01110 14 01111 15 10000 16 10001 17 10010 18 10011 19 10100 20 10101 21 10110 22 10111 23 11000 24 11001 25 11010 26 11011 27 11100 28 11101 29 11110 30 11111 31 6 COMPAND If set, audio data will be companded. 7 Law/A-Law This sets the audio companding mode. Law/A-Law Compand Mode 0 Law 1 A-Law Table 42. TX_MODE (0x56h/x66h) Bits Field 0 TX_MODE Description This sets the TX data output justification with respect to the SYNC signal. TX_MODE Description 0 MSB Justified 1 LSB Justified Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 57 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 42. TX_MODE (0x56h/x66h) (continued) Bits Field 5:1 MSB_POSITION Description This specifies the bit location of the MSB from the start of the frame (MSB Justified) or from the end of the frame (LSB Justified). MSB_POSITION Description 00000 0(Left Justified/PCM Long) 00001 1(I2S/PCM Short) 00010 2 00011 3 00100 4 00101 5 00110 6 00111 7 01000 8 01001 9 01010 10 01011 11 01100 12 01101 13 01110 14 01111 15 10000 16 10001 17 10010 18 10011 19 10100 20 10101 21 10110 22 10111 23 11000 24 11001 25 11010 26 11011 27 11100 28 11101 29 11110 30 11111 31 6 COMPAND If set, audio data will be companded. 7 Law/A-Law This sets the audio companding mode. Law/A-Law 58 Compand Mode 0 Law 1 A-Law Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Digital Effects Engine Digital Signal Processor (DSP) The LM49352 is designed to handle the entire audio signal conditioning and processing within the audio system, thereby freeing up the workload of any other applications processor contained within the system. The LM49352 features two independent DSPs, one for the DAC and the other for the ADC. Each DSP is fully featured and performs as a professional quality digital audio effects engine. Both DSP engines feature digital volume control, automatic level control (ALC), digital soft clip compression, and a 5-band parametric EQ. The effects chain of each DSP engine is shown by the diagrams below. Figure 66. ADC DSP Effects Chain -78 dB to +18 dB ALC SOFT CLIP DIG Gain & NG Mutes 5 Band EQ DIG MIXER LEFT DAC RIGHT DAC Distort Figure 67. DAC DSP Effects Chain The ADC and DAC DSP engines can be cascaded together in any order via the digital mixer to combine different audio effects to the same signal path. For example, a signal can be processed with high-pass filtering from the ADC effects engine with ALC from the DAC effects engine. The 5-band parametric EQs from each DSP engine can be combined to form a single 10-band parametric EQ or a single 5-band parametric EQ with 30dB (instead of 15dB) gain control for each band. Table 43. ADC EFFECTS (0x70h) Bits Field 0 ADC_HPF_ENB This enables the ADC's High Pass Filter. Description 1 ADC_ALC_ENB This enables the ADC's Automatic Level Control. 2 ADC_PK_ENB This enables the ADC's Peak Detector. 3 ADC_EQ_ENB This enables the ADC's 5-band Parametric EQ. 4 ADC_SCLP_ENB This enables the ADC's Soft Clip Feature. Table 44. DAC EFFECTS (0x71h) Bits Field 0 DAC_ALC_ENB 1 DAC_PK_ENB Description This enables the DAC's Automatic Level Control. This enables the DAC's Peak Detector. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 59 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 44. DAC EFFECTS (0x71h) (continued) Bits Field 2 DAC_EQ_ENB 3 RSVD 4 ADC_SCLP_ENB Description This enables the DAC's 5-band Parametric EQ. Reserved This enables the DAC's Soft Clip Feature. Table 45. HPF MODE (0x80h) Bits Field Description 2:0 HPF_MODE This configures the ADC's High Pass Filter (HPF). To calculate the -3dB cutoff frequency, multiply the coefficient by the sample rate (Hz): fC = Xn.fS(Hz) HPF_MODE Coefficient Filter Characteristics 000 X0 = 0.0275 8kHz Voice 001 X1 = 0.01833 12kHz Voice 010 X2 = 0.01375 16kHz Voice 011 X3 = 0.009166 24kHz Voice 100 X4 = 0.006875 fC = 220Hz for: 32kHz Voice fC = 100Hz for: 101 X5 = 0.003125 110 X6 = 0.0020833 32kHz Audio 48kHz Audio fC = 150Hz for: 111 X7 = 0.0015625 96kHz Audio ALC Overview The Automatic Level Control (ALC) system can be used to regulate the audio output level to a user defined target level. The ALC feature is especially useful whenever the level of the audio input is unknown, unpredictable, or has a large dynamic range. The main purpose of the ALC is to optimize the dynamic range of the audio input to audio output path. There are two separate and independent ALC circuits in the LM49352. One of the ALC circuits is located within the DAC DSP effects block. The other ALC circuit is integrated into the ADC DSP effects block. The DAC ALC controls the DAC digital gain. The ADC ALC controls the mono/auxiliary input amplifier gain or microphone preamplifier gain. The dual ALCs can be used to regulate the level of the analog (AUX, MONO, MIC) and digital (Port1 Data In, Port2 Data In) audio inputs. The ALC regulated output can be routed to any of the LM49352's amplifier outputs for playback. The ALC regulated output can also be routed to Audio Port1 or Audio Port2 for digital data transmission via I2S or PCM. Only audio inputs that are considered signals (rather than noise) are sent to the ALC's peak detector block. The peak detector compares the level of the audio input versus the ALC target level (TARGET_LEVEL). Signals lower than the target level will be amplified and signals higher than the target level will be attenuated. Any audio input that is lower than the level specified by the noise floor level (NOISE_FLOOR) will be considered as noise and will be gated from the ALC's peak detector in order to avoid noise pumping. So it is important to set NOISE_FLOOR to correlate with the signal to noise ratio of the corresponding audio path. In some instances (ie. Conference calls), it may be desirable to mute audio input signals that consist solely of background noise from the audio output. This is accomplished by enabling the ALC's noise gate (NG_ENB). When the noise gate is enabled, signals lower than the noise floor level will be muted from the audio output. If the audio input signal is below the target level, the ALC will increase the gain of the corresponding volume control until the signal reaches the target level. The rate at which the ALC performs gain increases is known as decay rate (DECAY RATE). But before each ALC gain increase the ALC must wait a predetermined amount of time (HOLD TIME). If the audio input signal is above the target level, the ALC will decrease the gain of the corresponding volume control until the signal reaches the target level. The rate at which the ALC performs attenuation is known as attack rate (ATTACK RATE). The ALC's peak detector tracks increases in audio input 60 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 signal amplitude instantaneously, but tracks decreases in audio input signal amplitude at programmable rate (PEAK DECAY TIME). ATTACK RATE, DECAY RATE, HOLD TIME, and PEAK DECAY TIME are fully adjustable which allows flexible operation of the ALC circuit. The ALC's timers are based on the sample rate of the DAC or ADC, so the closest corresponding sample rate must be programmed into the DAC SAMPLE setting (for DAC ALC) or the ADC SAMPLE (for ADC ALC). Audio Input ALC Output TARGET HOLD DECAY ATTACK Figure 68. ALC Example Limiter The LM49352's ALC features a limiter function. The purpose of the limiter is to limit the maximum level of the audio signal to the specified ALC target level. When the limiter is enabled, the ALC will decrease the gain of the volume control whenever the audio signal is higher than the specified target level. The programmed I2C gain setting when the limiter is first enabled is the maximum gain setting that the ALC limiter will apply to the audio signal. Gain increases beyond the original I2C gain setting are disabled. This is in contrast to ALC operation with the limiter disabled, where the ALC may increase gain of audio signals below target level using gain settings beyond the original I2C gain setting. Therefore, it is important to set the gain of the audio path to the desired setting before enabling the ALC limiter function. The limiter's target level can be set just below the clipping level of the output amplifier or ADC in order to prevent harsh distortions delivered to the loudspeaker or headphone on the receiving end. This method of ALC limiter operation is also known as "no clip" mode. Operating the ALC limiter in "no clip" mode maximizes the dynamic range of the audio amplifier or ADC while ensuring that the audio signal will never clip. Utilizing the ALC limiter in "no clip" mode also protects the loudspeaker from damage due to harmful overdriven conditions. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 61 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com The ALC limiter's target level can also be set for a predetermined maximum output power or voltage level. This method of ALC limiter operation is known as "power limit" mode. Operating the ALC limiter in "power limit" mode prevents the speaker or headphone from playing at unsafe hearing levels that can permanently damage the end user's ears. "Power limit" operation is especially useful for applications such as listening to music through a set of headphones. Another benefit of using the ALC limit in "power limit" mode is to extend battery life by reducing power consumption of the output amplifiers during audio playback. Audio Input ALC Output with Limiter Enabled TARGET ALC Output with Limiter Disabled TARGET Figure 69. ALC Limiter 62 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 46. ADC_ALC_1 (0x81h) Bits Field 2:0 ADC_SAMPLE Description This programs the timers on the ALC with the closest sample rate of the ADC. ADC_SAMPLE Expected ADC fS 000 8kHz 001 12kHz 010 16kHz 011 24kHz 100 32kHz 101 48kHz 110 96kHz 111 192kHz 3 LIMITER If set, the circuit will never apply gain to the signal, no matter how small, but it will attenuate the signal as soon as it reaches target and release it at the decay rate, once signal level reduces below target. The I2C gain setting (at the time the LIMITER is enabled) is the maximum gain that the ALC will apply. Care should be taken when choosing the optimum I2C gain setting whenever enabling the Limiter. 4 STEREO LINK If set, the ALC circuit uses the stereo average of the input signals to control the gain of the stereo output. This maintains stereo imaging. If this bit is cleared, then both channels operate as dual mono. 5 SOURCE_RSEL If both SOURCE_OVR and this bit is set, the right ADC ALC channel will be active. 6 SOURCE_LSEL If both SOURCE_OVR and this bit is set, the left ADC ALC channel will be active. 7 SOURCE_OVR If set, the active channel of the ADC ALC is determined by SOURCE_RSEL and SOURCE_LSEL. If cleared, the active channel of the ADC ALC is determined by the selected input to the ADC. MONO enables left ALC, AUX enables right ALC, MIC enables left and / or right ALC depending on which ADC channel MIC is selected to. Bits Field Description 3:0 NOISE_FLOOR This sets the anticipated noise floor. Signals lower than the noise floor specified will be gated from the ALC to avoid noise pumping. Table 47. ADC_ALC_2 (0x82h) 4 NG_ENB NOISE_FLOOR Noise Floor (dB) 0000 -39 0001 -42 0010 -45 0011 -48 0100 -51 0101 -54 0110 -57 0111 -60 1000 -63 1001 -66 1010 -69 1011 -72 1100 -75 1101 -78 1110 -81 1111 -84 This enables the Noise Gate. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 63 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 48. ADC_ALC_3 (0x83h) 64 Bits Field 4:0 TARGET_LEVEL Description This sets the desired target output level. Signals lower than this will be amplified and signals larger than this will be attenuated. TARGET_LEVEL Target Level (dB) 00000 -1.5 00001 -3 00010 -4.5 00011 -6 00100 -7.5 00101 -9 00110 -10.5 00111 -12 01000 -13.5 01001 -15 01010 -16.5 01011 -18 01100 -19.5 01101 -21 01110 -22.5 01111 -24 10000 -25.5 10001 -27 10010 -28.5 10011 -30 10100 -31.5 10101 -33 10110 -34.5 10111 -36 11000 -37.5 11001 -39 11010 -40.5 11011 -42 11100 -43.5 11101 -45 11110 -46.5 11111 -48 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 49. ADC_ALC_4 (0x84h) Bits Field 4:0 ATTACK_RATE Description This sets the rate at which the ALC will reduce gain if it detects the input signal is large. ATTACK_RATE Time between gain steps (s) 00000 21 00001 42 00010 83 00011 167 00100 250 00101 333 00110 417 00111 542 01000 729 01001 958 01010 1250 (Default) 01011 1604 01100 1896 01101 2208 01110 2792 01111 3708 10000 4792 10001 5688 10010 6563 10011 8396 10100 11000 10101 14167 10110 17083 10111 20000 11000 25000 11001 32000 11010 45000 11011 60000 11100 75000 11101 87500 11110 100000 11111 114583 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 65 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 50. ADC_ALC_5 (0x85h) Bits Field Description 4:0 DECAY_RATE This sets the rate at which the ALC will increase gain if it detects the input signal is too small. 7:5 66 PK_DECAY_RATE DECAY_RATE Time between gain steps (s) 00000 104 00001 125 00010 167 00011 250 00100 292 00101 396 00110 500 00111 708 01000 896 01001 1250 01010 1396 (Default) 01011 2000 01100 2708 01101 3500 01110 4750 01111 6250 10000 8000 10001 11000 10010 14000 10011 18500 10100 25000 10101 32000 10110 42000 10111 55000 11000 72500 11001 100000 11010 125000 11011 160000 11100 225000 11101 300000 11110 375000 11111 500000 (0.5s) PK_DECAY_RATE Max Time to track decay 000 1.3ms (Default) 001 2.6ms 010 5.3ms 011 10.6ms 100 21.3ms 101 42.6.3ms 110 85.5ms 111 2.73 secs Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 51. ADC_ALC_6 (0x86h) Bits Field 4:0 HOLD_TIME Description This sets how long the ALC circuit waits before increasing the gain. HOLD_TIME Time (ms) 00000 1 00001 1.25 00010 1.6 00011 2 00100 2.5 00101 3.2 00110 4 00111 5 01000 6.25 01001 8 01010 10 (Default) 01011 12.5 01100 16 01101 20 01110 25 01111 32 10000 40 10001 50 10010 64 10011 80 10100 100 10101 125 10110 160 10111 200 11000 250 11001 320 11010 400 11011 500 11100 640 11101 800 11110 1000 11111 1250 Table 52. ADC_ALC_7 (0x87h) Bits Field Description 5:0 MAX_LEVEL This sets the maximum allowed gain of the volume control to the output amplifier whenever the ALC is use. If the volume control is less than 6 bits the relevant LSBs are used as the limit and the MSBs are ignored. Table 53. ADC_ALC_8 (0x88h) Bits Field 5:0 MIN_LEVEL Description This sets the minimum allowed gain of the volume control to the output amplifier whenever the ALC is use. If the volume control is less than 6 bits the relevant LSBs are used as the limit and the MSBs are ignored. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 67 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 54. ADC_L_LEVEL (0x89h) Bits Field 5:0 ADC_L_LEVEL 6 68 STEREO_LINK Description This sets the post ADC digital gain of the left channel. ADC_L_LEVEL Level ADC_L_LEVEL Level 000000 -76.5dB 100000 -28.5dB 000001 -75dB 100001 -27dB 000010 -73.5dB 100010 -25.5dB 000011 -72dB 100011 -24dB 000100 -70.5dB 100100 -22.5dB 000101 -69dB 100101 -21dB 000110 -67.5dB 100110 -20.5dB 000111 -66dB 100111 -18dB 001000 -64.5dB 101000 -16.5dB 001001 -63dB 101001 -15dB 001010 -61.5dB 101010 -13.5dB 001011 -60dB 101011 -12dB 001100 -58.5dB 101100 -10.5dB 001101 -57dB 101101 -9dB 001110 -55.5dB 101110 -7.5dB 001111 -54dB 101111 -6dB 010000 -52.5dB 110000 -4.5dB 010001 -51dB 110001 -3dB 010010 -49.5dB 110010 -1.5dB 010011 -48dB 110011 0dB 010100 -46.5dB 110100 1.5dB 010101 -45dB 110101 3dB 010110 -43.5dB 110110 4.5dB 010111 -42dB 110111 6dB 011000 -40.5dB 111000 7.5dB 011001 -39dB 111001 9dB 011010 -37.5dB 111010 10.5dB 011011 -36dB 111011 12dB 011100 -34.5dB 111100 13.5dB 011101 -33dB 111101 15dB 011110 -31.5dB 111110 16.5dB 011111 -30dB 111111 18dB If set, this links the ADC_R_LEVEL with ADC_L_LEVEL. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 55. ADC_R_LEVEL (0x8Ah) Bits Field 5:0 ADC_R_LEVEL Description This sets the post ADC digital gain of the right channel. ADC_R_LEVEL Level ADC_R_LEVEL Level 000000 -76.5dB 100000 -28.5dB 000001 -75dB 100001 -27dB 000010 -73.5dB 100010 -25.5dB 000011 -72dB 100011 -24dB 000100 -70.5dB 100100 -22.5dB 000101 -69dB 100101 -21dB 000110 -67.5dB 100110 -20.5dB 000111 -66dB 100111 -18dB 001000 -64.5dB 101000 -16.5dB 001001 -63dB 101001 -15dB 001010 -61.5dB 101010 -13.5dB 001011 -60dB 101011 -12dB 001100 -58.5dB 101100 -10.5dB 001101 -57dB 101101 -9dB 001110 -55.5dB 101110 -7.5dB 001111 -54dB 101111 -6dB 010000 -52.5dB 110000 -4.5dB 010001 -51dB 110001 -3dB 010010 -49.5dB 110010 -1.5dB 010011 -48dB 110011 0dB 010100 -46.5dB 110100 1.5dB 010101 -45dB 110101 3dB 010110 -43.5dB 110110 4.5dB 010111 -42dB 110111 6dB 011000 -40.5dB 111000 7.5dB 011001 -39dB 111001 9dB 011010 -37.5dB 111010 10.5dB 011011 -36dB 111011 12dB 011100 -34.5dB 111100 13.5dB 011101 -33dB 111101 15dB 011110 -31.5dB 111110 16.5dB 011111 -30dB 111111 18dB Table 56. EQ_BAND_1 (0x8Bh) Bits Field Description 1:0 FREQ This sets the Sub-bass shelving filter's cut-off frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. FREQ Frequency (Hz) 00 60 01 80 10 100 11 120 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 69 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 56. EQ_BAND_1 (0x8Bh) (continued) Bits Field 6:2 LEVEL Description This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB Table 57. EQ_BAND_2 (0x8Ch) 70 Bits Field 1:0 FREQ Description This sets the Bass peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. FREQ Frequency (Hz) 00 150 01 200 10 250 11 300 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 57. EQ_BAND_2 (0x8Ch) (continued) Bits Field 6:2 LEVEL 7 Q Description This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB Programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 71 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 58. EQ_BAND_3 (0x8Dh) Bits Field Description 1:0 FREQ This sets the Mid peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 7 72 LEVEL Q FREQ Frequency (Hz) 00 600 01 800 10 1k 11 1.2k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB This programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 59. EQ_BAND_4 (0x8Eh) Bits Field Description 1:0 FREQ This sets the Treble peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 7 LEVEL Q FREQ Frequency (Hz) 00 2k 01 2.7k 10 3.4k 11 4.1k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB This programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 73 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 60. EQ_BAND_5 (0x8Fh) Bits Field Description 1:0 FREQ This sets the presence shelving filter's cut-off frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 74 LEVEL FREQ Frequency (Hz) 00 7k 01 9k 10 11k 11 13k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Digital Audio Compressor The LM49352 features a digital audio compressor on both the DAC and ADC paths. The compressor works by reducing the level of the audio signal that is higher than the level set by the audio compressor threshold level (THRESHOLD) by a fixed ratio (compressor output / compressor input) that is set by a predetermined audio compression ratio (RATIO). Higher compression ratios result in more compression as shown in Figure 70. The audio compressor can be used in conjunction with the ALC to limit audio peaks that the ALC may not be fast enough to react to. 1:1 Compression Ratio Audio Compressor Threshold Level 1:2 Compression Ratio 1:4 Compression Ratio Audio Compressor Output Level (dB) 1:215 Compression Ratio Audio Compressor Input Level (dB) Figure 70. Audio Compressor Effect Soft Knee Function The LM49352's audio compressor also features a soft knee function that smooths the harsh edges found during clipping of an audio signal. For audio signals higher than the compressor threshold level, the soft knee function gradually increases the compression ratio for increasing levels of audio signal beyond the compressor threshold. To achieve the smoothing effect to prevent hard clipping, the soft knee function initially compresses the audio signal at the smallest ratio and then incrementally increases the compression ratio if required. The highest level of compression applied by the soft knee function is set by the compressor ratio. The effect of the soft knee function is shown in Figure 71. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 75 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Soft Knee Enabled Audio Compressor Threshold Level 1:3.4 1:2.8 1:2.4 1:2 1:1.7 1:1.4 Audio Compressor Output Level (dB) 1:3.4 1:1.2 Soft Knee Disabled Audio Compressor Input Level (dB) Figure 71. Soft Knee Example with Compression Ratio Setting of 1:3.4 Table 61. SOFTCLIP1 (0x90h) 76 Bits Field 3:0 THRESHOLD Description This sets the threshold level of the audio compressor. Audio signals above the threshold will be compressed. THRESHOLD Threshold Level (dB) 0000 -36dB 0001 -30dB 0010 -24dB 0011 -20dB 0100 -18dB 0101 -17dB 0110 -16dB 0111 -15dB 1000 -14dB 1001 -12dB 1010 -10dB 1011 -8dB 1100 -6dB 1101 -4dB 1110 -2.5dB 1111 -1dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 61. SOFTCLIP1 (0x90h) (continued) Bits Field 4 SOFT_KNEE Description If set, the audio compressor will automatically apply higher compression ratios to audio signals higher than the threshold level. As the audio signal approaches levels higher than the threshold, SOFT_KNEE will increase the compression RATIO. The highest compression that the SOFT_KNEE algorithm will apply is the compression that is set by RATIO. Table 62. SOFTCLIP2 (0x91h) Bits Field 4:0 RATIO Description This sets the ratio at which the audio is compressed to when it passes beyond the threshold. In SOFT_KNEE mode this is the final level of compression. RATIO Ratio 00000 1:1 (Bypass) 00001 1:1.2 00010 1:1.4 00011 1:1.7 00100 1:2.0 00101 1:2.4 00110 1:2.8 00111 1:3.4 01000 1:4.0 01001 1:4.7 01010 1:5.7 01011 1:6.7 01100 1:8.0 01101 1:9.5 01110 1:11.3 01111 1:13.5 10000 1:16.0 10001 1:19.0 10010 1:22.8 10011 1:27.0 10100 1:32.0 10101 1:37.9 10110 1:45.5 10111 1:53.9 11000 1:64.0 11001 1:75.0 11010 1:91.0 11011 1:108 11100 1:128 11101 1:152 11110 1:182 11111 1:215 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 77 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 63. SOFTCLIP3 (0x92h) 78 Bits Field 3:0 LEVEL Description This sets the post compressor gain level. LEVEL Level (dB) 00000 -22.5dB 00001 -21dB 00010 -19.5dB 00011 -18dB 00100 -16.5dB 00101 -15dB 00110 -13.5dB 00111 -12dB 01000 -10.5dB 01001 -9dB 01010 -7.5dB 01011 -6dB 01100 -4.5dB 01101 -3dB 01110 -1.5dB 01111 0dB 10000 1.5dB 10001 3dB 10010 4.5dB 10011 6dB 10100 7.5dB 10101 9dB 10110 10.5dB 10111 12dB 11000 13.5dB 11001 15dB 11010 16.5dB 11011 18dB 11100 19.5dB 11101 21dB 11110 22.5dB 11111 24dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 DAC Effects Registers Table 64. DAC_ALC_1 (0xA0h) Bits Field 2:0 DAC_SAMPLE Description This programs the timers on the ALC with the closest DAC sample rate. DAC_SAMPLE Expected DAC fS 000 8kHz 001 12kHz 010 16kHz 011 24kHz 100 32kHz 101 48kHz 110 96kHz 111 192kHz 3 LIMITER If set, the circuit will never apply gain to the signal, no matter how small, but it will attenuate the signal as soon as it reaches target and release it at the decay rate, once signal level reduces below target. The I2C gain setting (at the time the LIMITER is enabled) is the maximum gain that the ALC will apply. Care should be taken when choosing the optimum I2C gain setting whenever enabling the Limiter. 4 STEREO LINK If set, the ALC circuit uses the stereo average of the input signals to control the gain of the stereo output. This maintains stereo imaging. If this bit is cleared, then both channels operate as dual mono. Table 65. DAC_ALC_2 (0xA1h) Bits Field 3:0 NOISE_FLOOR 4 NG_ENB Description This sets the anticipated noise floor. Signals lower than the specified noise floor will be gated from the ALC to avoid noise pumping. NOISE_FLOOR Noise Floor (dB) 0000 -39 0001 -42 0010 -45 0011 -48 0100 -51 0101 -54 0110 -57 0111 -60 1000 -63 1001 -66 1010 -69 1011 -72 1100 -75 1101 -78 1110 -81 1111 -84 This enables the Noise Gate Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 79 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 66. DAC_ALC_3 (0xA2h) 80 Bits Field 4:0 TARGET_LEVEL Description This sets the desired output level. Signals lower than this will be amplified and signals larger than this will be attenuated. TARGET_LEVEL Target Level (dB) 00000 -1.5 00001 -3 00010 -4.5 00011 -6 00100 -7.5 00101 -9 00110 -10.5 00111 -12 01000 -13.5 01001 -15 01010 -16.5 01011 -18 01100 -19.5 01101 -21 01110 -22.5 01111 -24 10000 -25.5 10001 -27 10010 -28.5 10011 -30 10100 -31.5 10101 -33 10110 -34.5 10111 -36 11000 -37.5 11001 -39 11010 -40.5 11011 -42 11100 -43.5 11101 -45 11110 -46.5 11111 -48 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 67. DAC_ALC_4 (0xA3h) Bits Field Description 4:0 ATTACK_RATE This sets the rate at which the ALC will reduce gain if it detects the input signal is too large. ATTACK_RATE Time between gain steps (s) 00000 21 00001 42 00010 83 00011 167 00100 250 00101 333 00110 417 00111 542 01000 729 01001 958 01010 1250 (Default) 01011 1604 01100 1896 01101 2208 01110 2792 01111 3708 10000 4792 10001 5688 10010 6563 10011 8396 10100 11000 10101 14167 10110 17083 10111 20000 11000 25000 11001 32000 11010 45000 11011 60000 11100 75000 11101 87500 11110 100000 11111 114583 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 81 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 68. DAC_ALC_5 (0xA4h) Bits Field 4:0 DECAY_RATE 7:5 PK_DECAY_RATE Description This sets the rate at which the ALC will increase gain if it detects the input signal is too small. DECAY_RATE Time between gain steps(us) 00000 104 00001 125 00010 167 00011 250 00100 292 00101 396 00110 500 00111 708 01000 896 01001 1250 01010 1396 (Default) 01011 2000 01100 2708 01101 3500 01110 4750 01111 6250 10000 8000 10001 11000 10010 14000 10011 18500 10100 25000 10101 32000 10110 42000 10111 55000 11000 72500 11001 100000 11010 125000 11011 160000 11100 225000 11101 300000 11110 375000 11111 500000 (0.5s) This sets how precise the ALC will track amplitude reductions of the audio input. The shorter the length of time for PK_DECAY_RATE, the more responsive the ALC will be when applying gain increases whenever the audio falls below target level. PK_DECAY_RATE 82 Time 000 1.3ms (Default) 001 2.6ms 010 5.3ms 011 10.6ms 100 21.3ms 101 42.6ms 110 85.5ms 111 2.73secs Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 69. DAC_ALC_6 (0xA5h) Bits Field 4:0 HOLD_TIME Description This sets how long the ALC circuit waits before increasing the gain. HOLDTIME Time (ms) 00000 1 00001 1.25 00010 1.6 00011 2 00100 2.5 00101 3.2 00110 4 00111 5 01000 6.25 01001 8 01010 10 (Default) 01011 12.5 01100 16 01101 20 01110 25 01111 32 10000 40 10001 50 10010 64 10011 80 10100 100 10101 125 10110 160 10111 200 11000 250 11001 320 11010 400 11011 500 11100 640 11101 800 11110 1000 11111 1250 Table 70. DAC_ALC_7 (0xA6h) Bits Field 5:0 MAX_LEVEL Description This sets the maximum allowed gain to the digital level control when the ALC is used. Table 71. DAC_ALC_8 (0xA7h) Bits Field 5:0 MIN_LEVEL Description This sets the minimum allowed gain to the digital level control when the ALC is used. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 83 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 72. DAC_L_LEVEL (0xA8h) Bits Field 5:0 DAC_L_LEVEL 6 84 STEREO_LINK Description This sets the pre DAC digital gain. DAC_L_LEVEL Level DAC_L_LEVEL Level 000000 -76.5dB 100000 -28.5dB 000001 -75dB 100001 -27dB 000010 -73.5dB 100010 -25.5dB 000011 -72dB 100011 -24dB 000100 -70.5dB 100100 -22.5dB 000101 -69dB 100101 -21dB 000110 -67.5dB 100110 -20.5dB 000111 -66dB 100111 -18dB 001000 -64.5dB 101000 -16.5dB 001001 -63dB 101001 -15dB 001010 -61.5dB 101010 -13.5dB 001011 -60dB 101011 -12dB 001100 -58.5dB 101100 -10.5dB 001101 -57dB 101101 -9dB 001110 -55.5dB 101110 -7.5dB 001111 -54dB 101111 -6dB 010000 -52.5dB 110000 -4.5dB 010001 -51dB 110001 -3dB 010010 -49.5dB 110010 -1.5dB 010011 -48dB 110011 0dB 010100 -46.5dB 110100 1.5dB 010101 -45dB 110101 3dB 010110 -43.5dB 110110 4.5dB 010111 -42dB 110111 6dB 011000 -40.5dB 111000 7.5dB 011001 -39dB 111001 9dB 011010 -37.5dB 111010 10.5dB 011011 -36dB 111011 12dB 011100 -34.5dB 111100 13.5dB 011101 -33dB 111101 15dB 011110 -31.5dB 111110 16.5dB 011111 -30dB 111111 18dB If set, this links DAC_R_LEVEL with DAC_L_LEVEL. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 73. DAC_R_LEVEL (0xA9h) Bits Field 5:0 DAC_R_LEVEL Description This sets the pre DAC digital gain. DAC_R_LEVEL Level DAC_R_LEVEL Level 000000 -76.5dB 100000 -28.5dB 000001 -75dB 100001 -27dB 000010 -73.5dB 100010 -25.5dB 000011 -72dB 100011 -24dB 000100 -70.5dB 100100 -22.5dB 000101 -69dB 100101 -21dB 000110 -67.5dB 100110 -20.5dB 000111 -66dB 100111 -18dB 001000 -64.5dB 101000 -16.5dB 001001 -63dB 101001 -15dB 001010 -61.5dB 101010 -13.5dB 001011 -60dB 101011 -12dB 001100 -58.5dB 101100 -10.5dB 001101 -57dB 101101 -9dB 001110 -55.5dB 101110 -7.5dB 001111 -54dB 101111 -6dB 010000 -52.5dB 110000 -4.5dB 010001 -51dB 110001 -3dB 010010 -49.5dB 110010 -1.5dB 010011 -48dB 110011 0dB 010100 -46.5dB 110100 1.5dB 010101 -45dB 110101 3dB 010110 -43.5dB 110110 4.5dB 010111 -42dB 110111 6dB 011000 -40.5dB 111000 7.5dB 011001 -39dB 111001 9dB 011010 -37.5dB 111010 10.5dB 011011 -36dB 111011 12dB 011100 -34.5dB 111100 13.5dB 011101 -33dB 111101 15dB 011110 -31.5dB 111110 16.5dB 011111 -30dB 111111 18dB Table 74. EQ_BAND_1 (0xABh) Bits Field Description 1:0 FREQ This sets the Sub-bass shelving filter's cut-off frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. FREQ Frequency (Hz) 00 60 01 80 10 100 11 120 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 85 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 74. EQ_BAND_1 (0xABh) (continued) Bits Field 6:2 LEVEL Description This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB Table 75. EQ_BAND_2 (0xACh) 86 Bits Field 1:0 FREQ Description This sets the Bass peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. FREQ Frequency (Hz) 00 150 01 200 10 250 11 300 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 75. EQ_BAND_2 (0xACh) (continued) Bits Field 6:2 LEVEL 7 Q Description This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB This programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 87 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 76. EQ_BAND_3 (0xADh) Bits Field Description 1:0 FREQ This sets the Mid peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 7 88 LEVEL Q FREQ Frequency (Hz) 00 600 01 800 10 1k 11 1.2k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB This programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 77. EQ_BAND_4 (0xAEh) Bits Field Description 1:0 FREQ This sets the Treble peak filter's center frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 7 LEVEL Q FREQ Frequency (Hz) 00 2k 01 2.7k 10 3.4k 11 4.1k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB This programs the width of the peak filter. Q Bandwidth 0 2/3 Octave 1 4/3 Octave Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 89 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 78. EQ_BAND_5 (0xAFh) Bits Field Description 1:0 FREQ This sets the presence shelving filter's cut-off frequency. The cut-off frequencies shown are based on a 48kHz sample rate. Using lower sample rates will scale down the cut-off frequencies proportionately. 6:2 90 LEVEL FREQ Frequency (Hz) 00 7k 01 9k 10 11k 11 13k This sets the gain at fC. LEVEL Effect 00000 Off (0dB) 00001 -15dB 00010 -14dB 00011 -13dB 00100 -12dB 00101 -11dB 00110 -10dB 00111 -9dB 01000 -8dB 01001 -7dB 01010 -6dB 01011 -5dB 01100 -4dB 01101 -3dB 01110 -2dB 01111 -1dB 10000 0dB 10001 1dB 10010 2dB 10011 3dB 10100 4dB 10101 5dB 10110 6dB 10111 7dB 11000 8dB 11001 9dB 11010 10dB 11011 11dB 11100 12dB 11101 13dB 11110 14dB 11111 15dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 79. SOFTCLIP1 (0xB0h) Bits Field Description 3:0 TRESHOLD This sets the threshold level of the audio compressor. Audio signals above the threshold will be compressed. 4 SOFT_KNEE THRESHOLD Threshold Level (dB) 0000 -36dB 0001 -30dB 0010 -24dB 0011 -20dB 0100 -18dB 0101 -17dB 0110 -16dB 0111 -15dB 1000 -14dB 1001 -12dB 1010 -10dB 1011 -8dB 1100 -6dB 1101 -4dB 1110 -2.5dB 1111 -1dB If set, the audio compressor will automatically apply higher compression ratios to audio signals higher than the threshold level. As the audio signal approaches levels higher than the threshold, SOFT_KNEE will increase the compression RATIO. The highest compression that the SOFT_KNEE algorithm will apply is the compression that is set by RATIO. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 91 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Table 80. SOFTCLIP2 (0xB1h) 92 Bits Field 4:0 RATIO Description This sets the ratio at which the audio is compressed to when it passes beyond the threshold. In soft clip mode this is the final level of compression. RATIO Ratio 00000 1:1 (Bypass) 00001 1:1.2 00010 1:1.4 00011 1:1.7 00100 1:2.0 00101 1:2.4 00110 1:2.8 00111 1:3.4 01000 1:4.0 01001 1:4.7 01010 1:5.7 01011 1:6.7 01100 1:8.0 01101 1:9.5 01110 1:11.3 01111 1:13.5 10000 1:16.0 10001 1:19.0 10010 1:22.8 10011 1:27.0 10100 1:32.0 10101 1:37.9 10110 1:45.5 10111 1:53.9 11000 1:64 11001 1:75.9 11010 1:91.0 11011 1:108 11100 1:128 11101 1:152 11110 1:182 11111 1:215 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 81. SOFTCLIP3 (0xB2h) Bits Field 4:0 LEVEL Description This sets the post compressor gain level. LEVEL Level (dB) 00000 -22.5dB 00001 -21dB 00010 -19.5dB 00011 -18dB 00100 -16.5dB 00101 -15dB 00110 -13.5dB 00111 -12dB 01000 -10.5dB 01001 -9dB 01010 -7.5dB 01011 -6dB 01100 -4.5dB 01101 -3dB 01110 -1.5dB 01111 0dB 10000 1.5dB 10001 3dB 10010 4.5dB 10011 6dB 10100 7.5dB 10101 9dB 10110 10.5dB 10111 12dB 11000 13.5dB 11001 15dB 11010 16.5dB 11011 18dB 11100 19.5dB 11101 21dB 11110 22.5dB 11111 24dB Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 93 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com GPIO Registers Table 82. GPIO1 (0xE0h) Bits Field 5:0 GPIO_MODE 5:0 GPIO_MODE 6 94 GPIO_TX Description This sets the mode of the GPIO Pin. GPIO_MODE GPIO STATUS 000000 GPIO Mode is disabled .PORT2_SDO is controlled by the Port2 serial interface configuration. In all the other modes PORT2_SDO is configured as the GPIO pin. 000001 GPIO_RX (in) 000010 CHIP ENABLE (in) 000011 CHIP ENABLE (in) 000100 ADC MUTE (in) 000101 ADC MUTE (in) 000110 HP SENSE (in) 000111 HP SENSE (in) 001000 SPARE (in) 001001 SPARE (in) 001010 GPIO TX (out) 001011 CHIP ACTIVE (out) 001100 CHIP ACTIVE (out) 001101 HP ENABLE (out) 001110 HP ENABLE (out) 001111 LS ENABLE (out) 010000 LS ENABLE (out) 010001 EP ENABLE (out) 010010 EP ENABLE (out) 010011 ADC CLIPPED (out) 010100 ADC CLIPPED (out) 010101 DAC CLIPPED (out) 010110 DAC CLIPPED (out) 010111 SOMETHING CLIPPED (out) 011000 SOMETHING CLIPPED (out) 011001 ADC NG ACTIVE (out) 011010 ADC NG ACTIVE (out) 011011 DAC NG ACTIVE (out) 011100 DAC NG ACTIVE (out) 011101 THERMAL (out) 011110 THERMAL (out) 011111 LS SHORT CCT (out) 100000 LS SHORT CCT (out) 100001 ANALOG ERROR Thermal or LS CCT condition (out) 100010 ANALOG ERROR (out) 100011 ERROR (out) Thermal or LS CCT or Clipping 100100 ERROR (out) 100101 - 111111 RESERVED Whenever GPIO_MODE is set to '001010', the GPIO pin will output a logic level based on this bit setting. Setting this bit high will result in a logic high GPIO output. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Table 82. GPIO1 (0xE0h) (continued) Bits Field 7 GPIO_RX Description This bit reports the logic level is present on the GPIO pin. Table 83. GPIO2 (0xE1h) Bits Field Description 0 SHORT This bit will go high whenever a short circuit condition occurs on the Class D loudspeaker amplifier outputs. Once triggered by a short circuit event, an I2C write of 1 to this bit clear this bit. 1 TEMP This bit will go high whenever the temperature of the LM49352 reaches a critical temperature. Once triggered by a thermal event, an I2C write of 1 to this bit clear this bit. Table 84. RESET (0xF0h) Bits Field 4:0 RSVD 5 SOFT_RESET Description Reserved. Setting this bit resets the digital core of LM49352. SOFT_RESET does not affect the current I2C register settings. Table 85. Spread Spectrum (0xF1h) Bits Field 1:0 RSVD 2 SS_DISABLE Description Reserved If this bit is set, Spread Spectrum mode will be disabled from the Class D amplifier. Table 86. FORCE (0xFE) Bits Field 0 RSVD 1 DACREF Description Reserved This bit determines whether the DAC reference voltage is internally generated or externally driven. DACREF 2 CP_FORCE STATUS 0 DACREF uses an internal bandgap reference. 1 DACREF is driven by an external voltage reference. If set, a -LS_VDD rail will be generated on HP_VSS, even if the headphone output stage is not required. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 95 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Schematic Diagram Figure 72. Demo Board Schematic 96 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Demonstration Board Layout Figure 73. Top Silkscreen Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 97 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Figure 74. Top Layer Figure 75. Inner Layer 2 98 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 Figure 76. Inner Layer 3 Figure 77. Bottom Layer Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 99 LM49352 SNAS467E - MARCH 2009 - REVISED MARCH 2013 www.ti.com Figure 78. Bottom Silkscreen Revision History 100 Rev Date Description 1.0 05/03/10 Initial released. 1.01 06/30/10 Fixed a typo in the I2C Timing Parameters table. Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 LM49352 www.ti.com SNAS467E - MARCH 2009 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision D (March 2013) to Revision E * Page Changed layout of National Data Sheet to TI format ........................................................................................................ 100 Submit Documentation Feedback Copyright (c) 2009-2013, Texas Instruments Incorporated Product Folder Links: LM49352 101 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) LM49352RL/NOPB ACTIVE DSBGA YPG 36 250 Green (RoHS & no Sb/Br) SNAG Level-1-260C-UNLIM -40 to 85 GL5 LM49352RLX/NOPB ACTIVE DSBGA YPG 36 1000 Green (RoHS & no Sb/Br) SNAG Level-1-260C-UNLIM -40 to 85 GL5 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM49352RL/NOPB DSBGA YPG 36 250 178.0 12.4 LM49352RLX/NOPB DSBGA YPG 36 1000 178.0 12.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.43 3.59 0.76 8.0 12.0 Q1 3.43 3.59 0.76 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM49352RL/NOPB DSBGA YPG LM49352RLX/NOPB DSBGA YPG 36 250 210.0 185.0 35.0 36 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YPG0036xxx D 0.6500.075 E RLA36XXX (Rev A) D: Max = 3.305 mm, Min =3.245 mm E: Max = 3.305 mm, Min =3.245 mm 4214895/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM49352RL/NOPB LM49352RLEVAL LM49352RLX/NOPB