DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS Class 2, Y5V Product Specification - Apr 05, 2004 V.8 6.3/10 V Phycomp Product specification Surface-mount ceramic multilayer capacitors FEATURES Class 2, Y5V 6.3/10 V QUICK REFERENCE DATA * Six standard sizes DESCRIPTION VALUE * High capacitance per unit volume Rated voltage Ur (DC) 6.3 V, 10 V * Supplied in tape on reel or in bulk case Capacitance range (E3 series) 100 nF to 47 F; note 1 Tolerance on capacitance -20% to +80% Test voltage (DC) for 1 minute: 2.5 x Ur Sectional specifications IEC 60384-10, second edition 1989-04; also based on CECC 32 100 * NiSn terminations. APPLICATIONS Detailed specification based on CECC 32 101-801 * Consumer electronics, for example: End terminations NiSn Climatic category (IEC 60 68) 25/85/21 - Tuners - Television receivers - Video recorders Note 1. Measured at 25 C, 1 V, 1 kHz for C < 22 F and 0.5 V, 120 Hz for C 22 F, using a four-gauge method. - All types of cameras. DESCRIPTION terminations The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. electrodes The inner electrodes are connected to the two terminations and finally covered with a layer of plated tin (NiSn). A cross section of the structure is shown in Fig.1. MLB457 ceramic material Fig.1 2004 Apr 05 Rev.8 Construction of a ceramic multilayer capacitor. 2 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V MECHANICAL DATA W T L2 L4 L3 MBB211 L1 For dimensions see Table 1. Fig.2. Component outline. Physical dimensions Table 1 Capacitor dimensions; see Fig.2 L1 CASE SIZE L2 and L3 . T MIN. MAX. MIN. MAX. L4 MIN. W Dimensions in millimetres 0402 1.0 0.05 0.50 0.05 0.45 0.55 0.15 0.30 0.40 0603 1.6 0.10 0.8 0.07 0.73 0.87 0.25 0.65 0.40 0805 2.0 0.10 1.25 0.10 1.15 1.35 0.25 0.75 0.55 1206 3.2 0.20 1.6 0.15 1.45 1.75 0.25 0.75 1.40 1210 3.2 0.20 2.5 0.20 1.70 2.20 0.25 0.75 1.40 1812 4.5 0.20 3.2 0.20 2.30 2.70 0.25 0.75 2.20 Dimensions in inches 0402 0.040 0.002 0.020 0.002 0.018 0.022 0.008 0.012 0.016 0603 0.063 0.004 0.032 0.003 0.029 0.035 0.010 0.026 0.016 0805 0.079 0.004 0.049 0.004 0.020 0.053 0.010 0.030 0.022 1206 0.126 0.008 0.063 0.006 0.020 0.069 0.010 0.030 0.056 1210 0.126 0.008 0.098 0.006 0.067 0.087 0.010 0.030 0.056 1812 0.177 0.006 0.126 0.006 0.091 0.106 0.010 0.030 0.087 2004 Apr 05 Rev.8 3 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V SELECTION CHART FOR 6.3 V 6.3 V C (nF) LAST TWO DIGITS OF 12NC 0402 470 58 0.5 0.05 680 - 1,000 63 1,500 65 2,200 67 3,300 69 4,700 72 6,800 74 10,000 76 15,000 78 22,000 81 47,000 85 0603 0805 1206 1210 0.5 0.05 0.8 0.07 1.15 0.10 1.25 0.10 1.6 0.15 2.0 0.2 Note 1. Values in shaded cells indicate thickness class. SELECTION CHART FOR 10 V C (nF) LAST TWO DIGITS OF 12NC 100 49 150 52 220 54 330 - 470 58 680 - 1,000 63 1,500 65 2,200 67 3,300 69 4,700 72 6,800 74 10,000 76 15,000 78 22,000 81 47,000 85 10 V 0402 0603 0805 1206 1210 1812 0.5 0.05 0.8 0.07 0.85 0.10 0.8 0.07 1.25 0.10 1.15 0.10 1.25 0.10 1.9 0.2 1.6 0.15 1.5 0.10 2.5 0.2 Note 1. Values in shaded cells indicate thickness class. 2004 Apr 05 Rev.8 4 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V Thickness classification and packing quantities THICKNESS CLASSIFICATION (mm) 0.5 0.05 0.8 0.07 0.85 0.10 1.15 0.10 1.25 0.10 1.5 0.10 1.6 0.15 1.9 0.2 2.0 0.2 2.5 0.2 2004 Apr 05 Rev.8 8 mm TAPE WIDTH QUANTITY PER REEL 180 mm; 7" 330 mm; 13" 12 MM TAPE WIDTH QUANTITY PER REEL QUANTITY PER BULK CASE 180 mm; 7" BLISTER PAPER BLISTER PAPER BLISTER 1812 0402 0603 0805 10,000 4,000 4,000 - - - - - - - - - - 3,000 3,000 2,000 2,500 2,000 1,000 - 50,000 15,000 15,000 - - - - - - - - - - 10,000 10,000 - 7,000 - - - - - - - - - - - - 500 50,000 - - - - - - - - - 50,000 15,000 - - - - - - - - - - - - 5,000 - - - - - 5 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V ORDERING INFORMATION Components may be ordered by using either a Phycomp's unique 12NC or simple 15-digit clear text code. Ordering code 12NC (preferred) 2 2 X X X X X X 9 X X X Capacitance value(1) Carrier type 22 blister 38 paper 50 blister (6.3 V) 55 paper (6.3 V) 54 bulk Tolerance 8 -20/+80% Rated voltage - Termination 20 6.3 V; NiSn 24 10 V; NiSn Size 7 0402 6 0603 0 0805 1 1206 2 1210 4 1812 CCB239_a Packaging(2) 1 reel: 180 mm; 7" 5 reel: 330 mm; 13" 4 bulk case (1) Refer to chapter "Selection chart for 6.3 V" and "Selection chart for 10 V" (2) Quantity on reel depends on thickness classification, see section "Thickness classification and packing quantities". Clear text code EXAMPLE: 06032F105Z24BB0D Size Code 0402 0603 0805 1206 1210 Temp. Char. Capacitance Tol. 2F = Y5V 105 = 1000000 Z = -20 /+80% pF; the third digit signifies the multiplying factor: Vol. Termination 5 = 6.3 V B = NiSn 6 = 10 V 5 = x 100,000 6 = x 1,000,000 Packing Marking Series 2 = 180 mm; 7" paper 3 = 330 mm; 13" paper B = 180 mm; 7" blister F = 330 mm; 13" blister P = bulk case 0 = no marking D = BME 1812 2004 Apr 05 Rev.8 6 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V ELECTRICAL CHARACTERISTICS Class 1 capacitors; Y5V dielectric; NiSn terminations Unless otherwise stated all electrical values apply at an ambient temperature of 25 1 C, an atmospheric pressure of 86 to 105 kPa, and a relative humidity of 63 to 67%. DESCRIPTION VALUE Capacitance range (E6 series); note 1 100 nF to 47 F Tolerance on capacitance after 1,000 hours -20% to +80% (Z) Tan ; note 1 All 10 V (except 0402 and 220nF, 1210 and 22 F; 1812 and 47 F) 12.5% 6.3 V: 1210 and 22 F, 1812 and 47 F 15% 10 V: 0402 and 220 nF 15% Insulation resistance after 1 minute at Ur (DC) Rins x C 500 seconds Ageing typical 7% per time decade Resistance to soldering heat 260 C; 10 seconds Note 1. Measured at 25 C, 1 V, 1 kHz for C < 22 F and 0.5 V, 120 Hz for C 22 F, using a four-gauge method. 2004 Apr 05 Rev.8 7 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V TESTS AND REQUIREMENTS Table 2 Test procedures and requirements IEC 60384-10/ CECC 32 100 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS 4.4 mounting the capacitors may be mounted on printed-circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive no visible damage 4.5 visual inspection and dimension check any applicable method using x10 magnification in accordance with specification 4.6.1 capacitance at 25 C C < 22 F, f = 1 kHz, 1 Vrms C 22 F, f = 120 Hz, 0.5 Vrms within specified tolerance 4.6.2 tan at 25 C C < 22 F, f = 1 kHz, 1 Vrms C 22 F, f = 120 Hz, 0.5 Vrms in accordance with specification 4.6.3 insulation resistance at Ur (DC) for 1 minute in accordance with specification 4.6.4 voltage proof 2.5 x Ur for 1 minute no breakdown or flashover 4.7.1 temperature coefficient between minimum and maximum temperature in accordance with specification 4.8 adhesion a force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate no visible damage 4.9 bond strength of plating on end face mounted in accordance with CECC 32 100, paragraph 4.4 no visible damage conditions: bending 1 mm at a rate of 1 mm/s, radius jig 340 mm lC/Cl: 30% preconditioning: the terminations shall be well tinned after recovery 4.10 Tb resistance to soldering heat resistance to leaching 2004 Apr 05 Rev.8 120 to 150 C during 1 minute; 260 5 C for 10 0.5 s in a static solder bath 260 5 C for 30 1 s in a static solder bath 8 lC/Cl: 20% tan : original specification Rins: original specification using visual enlargement of x10, dissolution of the terminations shall not exceed 10% www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V IEC 60384-10/ CECC 32 100 CLAUSE IEC 60068-2 TEST METHOD 4.11 Ta solderability zero hour test, and test after storage (20 to 24 months) in original packing in normal atmosphere; unmounted chips completely immersed for 2 0.5 s in a solder bath at 235 5 C the terminations shall be well tinned 4.12 Na rapid change of temperature preconditioning: -25 to +85 C; 5 cycles no visible damage after 48 hours recovery: TEST PROCEDURE REQUIREMENTS lC/Cl: 20% 4.14 Ca 4.15 2004 Apr 05 Rev.8 damp heat preconditioning: (thermal treatment): 500 12 hours at 40 C; 90 to 95% RH; no visible damage after 48 hours recovery: lC/Cl: +30%/-40% tan : 15% Rins: 500 M or RiCR 25 s, whichever is less damp heat; with Ur load initialization: 48 hours after Ur at 40 C; for 1 hour (for initial value measurement); 500 12 hours at 40 C; 90 to 95% RH; Ur applied pretreatment: endurance initialization: 2 x Ur at 85 C for 1 hour, (initial value measurement after 48 hours, recovery at room temperature) ; 1,000 hours at 85 C and 2 x Ur applied 9 Ur at 40 C for 1 hour, after 48 hours recovery: lC/Cl: +30%/-40% tan : 15% Rins: 500 M or RiCR 25 s, whichever is less pretreatment: Ur at 40 C for 1 hour, after 48 hours recovery: lC/Cl: +30%/-40% tan : 15% Rins: 1000 M or RiCR 50 s, whichever is less www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 6.3/10 V REVISION HISTORY Revision Date Change Notification Description Rev.5 2001 May 30 - - Converted to Phycomp brand. Rev.6 2003 Jun 26 - - Updated company logo. - Combined 6.3 V and 10 V data sheets. - Capacitance range changed, refer to selection chart. Rev.7 2003 Sep 26 - - Size 1206, 1210 L1 dimensions revised. - Tan 6.3 V, 10 V amended. Rev. 8 2004 Apr 05 - - Thickness for Y5V 1210 22uF 10V revised 2004 Apr 05 Rev.8 10 www.yageo.com