19-3158; Rev 0; 1/04 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs The MAX1274/MAX1275 low-power, high-speed, serialoutput, 12-bit, analog-to-digital converters (ADCs) operate at up to 1.8Msps. These devices feature true-differential inputs, offering better noise immunity, distortion improvements, and a wider dynamic range over singleended inputs. A standard SPITM/QSPITM/MICROWIRETM interface provides the clock necessary for conversion. These devices easily interface with standard digital signal processor (DSP) synchronous serial interfaces. The MAX1274/MAX1275 operate from a single +4.75V to +5.25V supply voltage and require an external reference. The MAX1274 has a unipolar analog input, while the MAX1275 has a bipolar analog input. These devices feature a partial power-down mode and a full power-down mode for use between conversions, which lower the supply current to 1mA (typ) and 1A (max), respectively. Also featured is a separate power-supply input (VL), which allows direct interfacing to +1.8V to VDD digital logic. The fast conversion speed, low-power dissipation, excellent AC performance, and DC accuracy (1 LSB INL) make the MAX1274/MAX1275 ideal for industrial process control, motor control, and base-station applications. The MAX1274/MAX1275 come in a 12-pin TQFN package, and are available in the commercial (0C to +70C) and extended (-40C to +85C) temperature ranges. Applications Data Acquisition Communications Bill Validation Portable Instruments Features 1.8Msps Sampling Rate Only 45mW (typ) Power Dissipation Only 1A (max) Shutdown Current High-Speed, SPI-Compatible, 3-Wire Serial Interface 70dB S/(N + D) at 525kHz Input Frequency Internal True-Differential Track/Hold (T/H) External Reference No Pipeline Delays Small 12-Pin TQFN Package Ordering Information PART TEMP RANGE PINPACKAGE INPUT MAX1274ACTC-T 0C to +70C 12 TQFN-12 Unipolar 0C to +70C MAX1274BCTC-T 12 TQFN-12 Unipolar MAX1274AETC-T -40C to +85C 12 TQFN-12 Unipolar MAX1274BETC-T -40C to +85C 12 TQFN-12 Unipolar MAX1275ACTC-T 0C to +70C 12 TQFN-12 MAX1275BCTC-T 0C to +70C 12 TQFN-12 Bipolar Bipolar MAX1275AETC-T -40C to +85C 12 TQFN-12 Bipolar MAX1275BETC-T -40C to +85C 12 TQFN-12 Bipolar Motor Control Pin Configuration TOP VIEW AIN+ N.C. SCLK 12 11 10 Typical Operating Circuit 0.01F 10F AIN- 1 9 CNVST REF 2 8 DOUT RGND 3 7 VL MAX1274 MAX1275 4 VDD 5 6 N.C. GND +1.8V TO VDD 4.75V TO +5.25V TQFN 0.01F VDD DIFFERENTIAL + INPUT VOLTAGE - 10F VL DOUT AIN+ AIN- MAX1274 MAX1275 C/DSP CNVST SCLK REF 4.7F REF 0.01F RGND GND SPI/QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX1274/MAX1275 General Description MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs ABSOLUTE MAXIMUM RATINGS VDD to GND ..............................................................-0.3V to +6V VL to GND ...................-0.3V to the lower of (VDD + 0.3V) or +6V Digital Inputs to GND ....................-0.3V to the lower of (VDD + 0.3V) or +6V Digital Output to GND .......................-0.3V to the lower of (VL + 0.3V) or +6V Analog Inputs and REF to GND.............-0.3V to the lower of (VDD + 0.3V) or +6V RGND to GND .......................................................-0.3V to +0.3V Maximum Current into Any Pin............................................50mA Continuous Power Dissipation (TA = +70C) 12-Pin TQFN (derate 16.9mW/C above +70C) ......1349mW Operating Temperature Ranges MAX127_ CTC ...................................................0C to +70C MAX127_ ETC.................................................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = +5V 5%, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, 50% duty cycle, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY Resolution 12 Relative Accuracy INL (Note 1) Differential Nonlinearity DNL (Note 2) Bits MAX127_A -1.0 +1.0 MAX127_B -1.75 +1.75 MAX127_A -1.0 +1.0 MAX127_B -1.0 +1.75 Offset Error 6.0 Offset-Error Temperature Coefficient Offset nulled 6.0 Gain Temperature Coefficient LSB LSB ppm/C 1 Gain Error LSB 2 LSB ppm/C DYNAMIC SPECIFICATIONS (fIN = 525kHz sine wave, VIN = VREF, unless otherwise noted.) Signal-to-Noise Plus Distortion SINAD Total Harmonic Distortion (Up to the 5th Harmonic) THD Spurious-Free Dynamic Range SFDR MAX127_A 69 70 MAX127_B 67 70 dB -80 -76 -83 -76 dB dB fIN1 = 250kHz, fIN2 = 300kHz -78 dB Full-Power Bandwidth -3dB point, small-signal method 20 MHz Full-Linear Bandwidth S/(N + D) 68dB, single ended 1.2 MHz Intermodulation Distortion IMD CONVERSION RATE Minimum Conversion Time tCONV (Note 3) Maximum Throughput Rate 1.8 Minimum Throughput Rate Track-and-Hold Acquisition Time (Note 4) tACQ Aperture Jitter 2 s Msps 10 ksps (Note 5) 104 5 ns (Note 6) 30 ps Aperture Delay External Clock Frequency 0.556 fSCLK _______________________________________________________________________________________ ns 28.8 MHz 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs (VDD = +5V 5%, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, 50% duty cycle, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS ANALOG INPUTS (AIN+, AIN-) Differential Input Voltage Range VIN AIN+ - AIN-, MAX1274 0 VREF AIN+ - AIN-, MAX1275 -VREF / 2 +VREF / 2 0 VDD V 1 A Absolute Input Voltage Range DC Leakage Current V Input Capacitance Per input pin 16 pF Input Current (Average) Time averaged at maximum throughput rate 75 A REFERENCE INPUT (REF) REF Input Voltage Range VREF VDD + 50mV 1.0 Input Capacitance 20 DC Leakage Current pF 1 Input Current (Average) Time averaged at maximum throughput rate V 400 A A DIGITAL INPUTS (SCLK, CNVST) Input Voltage Low VIL Input Voltage High VIH Input Leakage Current 0.3 x VL 0.7 x VL IIL V V 0.05 10 A 30 pF DIGITAL OUTPUT (DOUT) Output Load Capacitance COUT For stated timing performance Output Voltage Low VOL ISINK = 5mA, VL 1.8V Output Voltage High VOH ISOURCE = 1mA, VL 1.8V Output Leakage Current IOL Output high impedance 0.4 VL - 0.5V V V 0.2 10 A POWER REQUIREMENTS Analog Supply Voltage VDD 4.75 5.25 V Digital Supply Voltage VL 1.8 VDD V Analog Supply Current, Normal Mode IDD Analog Supply Current, Partial Power-Down Mode IDD Analog Supply Current, Full Power-Down Mode IDD Static, fSCLK = 28.8MHz 7 9 Static, no SCLK 4 5 Operational, 1.8Msps 9 11 fSCLK = 28.8MHz 1 No SCLK 1 fSCLK = 28.8MHz 1 No SCLK Operational, full-scale input at 1.8Msps Digital Supply Current (Note 7) PSR mA 1 1 2.5 Static, fSCLK = 28.8MHz 0.4 1 Partial/full power-down mode, fSCLK = 28.8MHz 0.2 0.5 Static, no SCLK, all modes Positive-Supply Rejection VDD = 5V 5%, full-scale input mA A mA 0.1 1 A 0.2 3.0 mV _______________________________________________________________________________________ 3 MAX1274/MAX1275 ELECTRICAL CHARACTERISTICS (continued) MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs TIMING CHARACTERISTICS (VDD = +5V 5%, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, 50% duty cycle, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN SCLK Pulse-Width High tCH VL = 1.8V to VDD 15.6 SCLK Pulse-Width Low tCL VL = 1.8V to VDD 15.6 SCLK Rise to DOUT Transition tDOUT TYP MAX UNITS ns ns CL = 30pF, VL = 4.75V to VDD 14 CL = 30pF, VL = 2.7V to VDD 17 CL = 30pF, VL = 1.8V to VDD 24 ns DOUT Remains Valid After SCLK tDHOLD VL = 1.8V to VDD 4 ns CNVST Fall to SCLK Fall tSETUP VL = 1.8V to VDD 10 ns tCSW VL = 1.8V to VDD 20 CNVST Pulse Width ns Power-Up Time; Full Power-Down TPWR-UP 2 ms Restart Time; Partial Power-Down tRCV 16 Cycles Note 1: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the gain error and the offset error have been nulled. Note 2: No missing codes over temperature. Note 3: Conversion time is defined as the number of clock cycles (16) multiplied by the clock period. Note 4: At sample rates below 10ksps, the input full-linear bandwidth is reduced to 5kHz. Note 5: The listed value of three SCLK cycles is given for full-speed continuous conversions. Acquisition time begins on the 14th rising edge of SCLK and terminates on the next falling edge of CNST. The IC idles in acquisition mode between conversions. Note 6: Undersampling at the maximum signal bandwidth requires the minimum jitter spec for SINAD performance. Note 7: Digital supply current is measured with the VIH level equal to VL, and the VIL level equal to GND. VL CNVST tCSW tSETUP tCL tCH SCLK DOUT tDHOLD tDOUT 6k DOUT DOUT 6k 4 GND GND a) HIGH-Z TO VOH, VOL TO VOH, AND VOH TO HIGH-Z Figure 1. Detailed Serial-Interface Timing CL CL b) HIGH-Z TO VOL, VOH TO VOL, AND VOL TO HIGH-Z Figure 2. Load Circuits for Enable/Disable Times _______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs 0.6 0.6 0.2 0.2 0.2 0 0 -0.2 -0.2 -0.2 -0.4 -0.4 -0.4 -0.6 -0.6 -0.6 -0.8 1000 2000 3000 4000 -0.8 0 5000 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 DIGITAL OUTPUT CODE DIGITAL OUTPUT CODE DIGITAL OUTPUT CODE DIFFERENTIAL NONLINEARITY vs. DIGITAL OUTPUT CODE (MAX1275) OFFSET ERROR vs. TEMPERATURE (MAX1274) OFFSET ERROR vs. TEMPERATURE (MAX1275) OFFSET ERROR (LSB) 0.4 0.2 0 -0.2 0.2 0.1 0 -0.1 0.75 0.50 0.25 0 -0.25 -0.4 -0.2 -0.50 -0.6 -0.3 -0.75 -0.4 -0.8 1000 2000 3000 4000 -1.00 -40 5000 -15 10 35 60 DIGITAL OUTPUT CODE TEMPERATURE (C) GAIN ERROR vs. TEMPERATURE (MAX1274) GAIN ERROR vs. TEMPERATURE (MAX1275) -1.5 -2.0 -15 10 35 85 60 FFT PLOT (MAX1274) 0 -1.5 -2.0 fSAMPLE = 2Msps fSCLK = 32MHz fIN = 100kHz SINAD = 70.74dB SNR = 70.82dB THD = -88.63dB SFDR = 87.07dB -20 AMPLITUDE (dB) -1.0 GAIN ERROR (LSB) -1.0 -40 TEMPERATURE (C) -0.5 MAX1274 toc07 -0.5 85 MAX1274 toc08 0 MAX1274 toc06 0.3 OFFSET ERROR (LSB) 0.6 1.00 MAX1274 toc05 0.4 MAX1274 toc04 0.8 5000 -40 -60 MAX1274 toc09 0 DNL (LSB) 0.4 INL (LSB) 0.4 0 DNL (LSB) 0.8 0.4 -0.8 GAIN ERROR (LSB) DIFFERENTIAL NONLINEARITY vs. DIGITAL OUTPUT CODE (MAX1274) MAX1274 toc02 0.6 INL (LSB) 0.8 MAX1274 toc01 0.8 INTEGRAL NONLINEARITY vs. DIGITAL OUTPUT CODE (MAX1275) MAX1274 toc03 INTEGRAL NONLINEARITY vs. DIGITAL OUTPUT CODE (MAX1274) -80 -100 -2.5 -2.5 -120 -3.0 -40 -15 10 35 TEMPERATURE (C) 60 85 -3.0 -40 -140 -15 10 35 TEMPERATURE (C) 60 85 0 200 400 600 800 1000 ANALOG INPUT FREQUENCY (kHz) _______________________________________________________________________________________ 5 MAX1274/MAX1275 Typical Operating Characteristics (VDD = +5V, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are measured at TA = +25C) Typical Operating Characteristics (continued) (VDD = +5V, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are measured at TA = +25C) FFT PLOT (MAX1275) -40 -60 -80 -40 -60 -80 -100 -100 -120 -120 -140 -140 200 400 600 800 1000 0 ANALOG INPUT FREQUENCY (kHz) -60 800 1000 -80 fSAMPLE = 2Msps fSCLK = 32MHz fIN = 500kHz SINAD = 70.84dB SNR = 71.11dB THD = -83.05dB SFDR = 84.68dB -20 AMPLITUDE (dB) -40 -60 -80 -100 -100 -120 -120 -140 -140 200 400 600 800 1000 0 200 400 600 800 ANALOG INPUT FREQUENCY (kHz) ANALOG INPUT FREQUENCY (kHz) FFT PLOT (MAX1275) TOTAL HARMONIC DISTORTION vs. SOURCE IMPEDANCE fSAMPLE = 2Msps fSCLK = 32MHz fIN = 500kHz SINAD = 70.55dB SNR = 70.73dB THD = -84.43dB SFDR = 85.16dB -20 -40 -60 -60 -80 -65 1000 -70 THD (dB) 0 MAX1274 toc14 0 MAX1274 toc15 AMPLITUDE (dB) -40 600 0 MAX1274 toc12 fSAMPLE = 2Msps fSCLK = 32MHz fIN = 300kHz SINAD = 70.66dB SNR = 71.09dB THD = -80.85dB SFDR = 81.26dB -20 400 FFT PLOT (MAX1274) FFT PLOT (MAX1275) 0 200 ANALOG INPUT FREQUENCY (kHz) MAX1274 toc13 0 fIN = 500kHz -75 -80 -85 -100 fIN = 100kHz -90 -120 -95 -140 -100 0 200 400 600 800 ANALOG INPUT FREQUENCY (kHz) 6 MAX1274 toc11 fSAMPLE = 2Msps fSCLK = 32MHz fIN = 300kHz SINAD = 70.88dB SNR = 71.24dB THD = -81.96dB SFDR = 83.65dB -20 AMPLITUDE (dB) fSAMPLE = 2Msps fSCLK = 32MHz fIN = 100kHz SINAD = 70.41dB SNR = 70.53dB THD = -85.92dB SFDR = 87.56dB -20 AMPLITUDE (dB) FFT PLOT (MAX1274) 0 MAX1274 toc10 0 AMPLITUDE (dB) MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs 1000 10 100 1000 SOURCE IMPEDANCE () _______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs fIN2 -60 -80 -120 -140 200 400 600 800 1000 0 200 400 600 800 1000 ANALOG INPUT FREQUENCY (kHz) ANALOG INPUT FREQUENCY (kHz) VDD/VL FULL POWER-DOWN SUPPLY CURRENT vs. TEMPERATURE VL PARTIAL/FULL POWER-DOWN SUPPLY CURRENT vs. TEMPERATURE 0.6 VDD, fSCLK = 28.8MHz 0.4 VDD, fSCLK = 0 0.2 VL = 5V, fSCLK = 28.8MHz VL SUPPLY CURRENT (A) 0.8 MAX1274 toc19 200 MAX1274 toc18 1.0 150 100 VL = 3V, fSCLK = 28.8MHz 50 VL, fSCLK = 0 0 -15 10 35 60 -40 85 -15 10 35 60 TEMPERATURE (C) TEMPERATURE (C) VDD SUPPLY CURRENT vs. TEMPERATURE VDD SUPPLY CURRENT vs. CONVERSION RATE MAX1274 toc20 12 CONVERTING fSCLK = 28.8MHz 9 6 PARTIAL POWER-DOWN fSCLK = 28.8MHz 12 85 MAX1274 toc21 0 -40 VDD SUPPLY CURRENT (mA) VDD/VL SUPPLY CURRENT (A) -80 -120 0 VDD SUPPLY CURRENT (mA) fIN2 -60 -100 -140 fIN1 -40 -100 3 fSAMPLE = 2Msps fSCLK = 32MHz fIN1 = 250.039kHz fIN2 = 300.059kHz IMD = -81.82dB -20 AMPLITUDE (dB) AMPLITUDE (dB) fIN1 MAX1274 toc16 fSAMPLE = 2Msps SCLK = 32MHz 32MHz fSCLK IN1 = =250.039kHz fIN1 300.059kHz IN2 = 250.039kHz fIN2 = 300.059kHz IMD = -84.23dB -20 -40 TWO-TONE IMD PLOT (MAX1275) 0 MAX1274 toc17 TWO-TONE IMD PLOT (MAX1274) 0 9 6 3 0 0 -40 -15 10 35 TEMPERATURE (C) 60 85 0 500 1000 1500 2000 fSAMPLE (kHz) _______________________________________________________________________________________ 7 MAX1274/MAX1275 Typical Operating Characteristics (continued) (VDD = +5V, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are measured at TA = +25C) Typical Operating Characteristics (continued) (VDD = +5V, VL = VDD, VREF = 4.096V, fSCLK = 28.8MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are measured at TA = +25C) VL SUPPLY CURRENT vs. CONVERSION RATE VL SUPPLY CURRENT vs. TEMPERATURE 0.6 FULL/PARTIAL POWER-DOWN fSCLK = 28.8MHz 0.4 MAX1274 toc23 CONVERTING fSCLK = 28.8MHz 0.8 1.0 VL SUPPLY CURRENT (mA) MAX1274 toc22 1.0 VL SUPPLY CURRENT (mA) MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs 0.8 VL = 5V 0.5 VL = 3V VL = 1.8V 0.3 0.2 0 -40 0 -15 10 35 60 85 0 500 1000 1500 2000 fSAMPLE (kHz) TEMPERATURE (C) Pin Description 8 PIN NAME 1 AIN- Negative Analog Input FUNCTION 2 REF External Reference Voltage Input. VREF sets the analog input range. Bypass REF with a 0.01F capacitor and a 4.7F capacitor to RGND. 3 RGND 4 VDD Positive Analog Supply Voltage (+4.75V to +5.25V). Bypass VDD with a 0.01F capacitor and a 10F capacitor to GND. 5, 11 N.C. No Connection 6 GND Ground. GND is internally connected to EP. 7 VL 8 DOUT Serial Data Output. Data is clocked out on the rising edge of SCLK. 9 CNVST Convert Start. Forcing CNVST high prepares the part for a conversion. Conversion begins on the falling edge of CNVST. The sampling instant is defined by the falling edge of CNVST. 10 SCLK Serial Clock Input. Clocks data out of the serial interface. SCLK also sets the conversion speed. 12 AIN+ -- EP Reference Ground. Connect RGND to GND. Positive Logic Supply Voltage (1.8V to VDD). Bypass VL with a 0.01F capacitor and a 10F capacitor to GND. Positive Analog Input Exposed Paddle. EP is internally connected to GND. _______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs VL MAX1274/MAX1275 VDD CAPACITIVE DAC REF CIN+ RIN+ AIN+ AIN + 12-BIT SAR ADC T/H AIN - OUTPUT BUFFER VAZ DOUT COMP CONTROL LOGIC AINCINCONTROL LOGIC AND TIMING RIN- ACQUISITION MODE CAPACITIVE DAC CNVST SCLK CIN+ RIN+ AIN+ MAX1274 MAX1275 VAZ RGND GND Figure 3. Functional Diagram Detailed Description The MAX1274/MAX1275 use an input T/H and successive-approximation register (SAR) circuitry to convert an analog input signal to a digital 12-bit output. The serial interface requires only three digital lines (SCLK, CNVST, and DOUT) and provides easy interfacing to microprocessors (Ps) and DSPs. Figure 3 shows the simplified internal structure for the MAX1274/MAX1275. True-Differential Analog Input T/H The equivalent circuit of Figure 4 shows the input architecture of the MAX1274/MAX1275, which is composed of a T/H, a comparator, and a switched-capacitor digital-to-analog converter (DAC). The T/H enters its tracking mode on the 14th SCLK rising edge of the previous conversion. Upon power-up, the T/H enters its tracking mode immediately. The positive input capacitor is connected to AIN+. The negative input capacitor is connected to AIN-. The T/H enters its hold mode on the falling edge of CNVST and the difference between the sampled positive and negative input voltages is converted. The time required for the T/H to acquire an input signal is determined by how quickly its input capacitance is charged. If the input signal's source impedance is high, the acquisition time lengthens. The acquisition time, tACQ, is the minimum time needed for COMP CONTROL LOGIC AINCIN- RIN- HOLD/CONVERSION MODE Figure 4. Equivalent Input Circuit the signal to be acquired. It is calculated by the following equation: tACQ 9 x (RS + RIN) x 16pF where RIN = 200, and RS is the source impedance of the input signal. Note: tACQ is never less than 104ns and any source impedance below 12 does not significantly affect the ADC's AC performance. Input Bandwidth The ADC's input-tracking circuitry has a 20MHz smallsignal bandwidth, making it is possible to digitize highspeed transient events and measure periodic signals with bandwidths exceeding the ADC's sampling rate by using undersampling techniques. To avoid high-frequency signals being aliased into the frequency band of interest, anti-alias filtering is recommended. Analog Input Protection Internal protection diodes that clamp the analog input to VDD and GND allow the analog input pins to swing from GND - 0.3V to VDD + 0.3V without damage. Both inputs must not exceed VDD or be lower than GND for accurate conversions. _______________________________________________________________________________________ 9 MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs A CNVST falling edge initiates a conversion sequence; the T/H stage holds the input voltage, the ADC begins to convert, and DOUT changes from high impedance to logic low. SCLK is used to drive the conversion process, and it shifts data out as each bit of the conversion is determined. SCLK begins shifting out the data after the 4th rising edge of SCLK. DOUT transitions t DOUT after each SCLK's rising edge and remains valid 4ns (tDHOLD) after the next rising edge. The 4th rising clock edge produces the MSB of the conversion at DOUT, and the MSB remains valid 4ns after the 5th rising edge. Since there are 12 data bits and 3 leading zeros, at least 16 rising clock edges are needed to shift out these bits. For continuous operation, pull CNVST high between the 14th and the 16th SCLK rising edges. If CNVST stays low after the falling edge of the 16th SCLK cycle, the DOUT line goes to a high-impedance state on either CNVST's rising edge or the next SCLK's rising edge. Serial Interface Initialization After Power-Up and Starting a Conversion Upon initial power-up, the MAX1274/MAX1275 require a complete conversion cycle to initialize the internal calibration. Following this initial conversion, the part is ready for normal operation. This initialization is only required after a hardware power-up sequence and is not required after exiting partial or full power-down mode. To start a conversion, pull CNVST low. At CNVST's falling edge, the T/H enters its hold mode and a conversion is initiated. SCLK runs the conversion and the data can then be shifted out serially on DOUT. Timing and Control Conversion-start and data-read operations are controlled by the CNVST and SCLK digital inputs. Figures 1 and 5 show timing diagrams, which outline the serialinterface operation. CNVST tSETUP 1 SCLK tACQUIRE CONTINUOUS-CONVERSION SELECTION WINDOW 16 POWER-MODE SELECTION WINDOW 2 3 HIGH IMPEDANCE 4 8 D11 DOUT D10 D9 D8 14 D7 D6 D5 D4 D3 D2 D1 D0 Figure 5. Interface-Timing Sequence CONVST MUST GO HIGH AFTER THE 3RD BUT BEFORE THE 14TH SCLK RISING EDGE CNVST ONE 8-BIT TRANSFER SCLK DOUT GOES HIGH IMPEDANCE ONCE CNVST GOES HIGH 1ST SCLK RISING EDGE DOUT MODE 0 0 0 D11 D10 NORMAL D9 D8 D7 PPD Figure 6. SPI Interface--Partial Power-Down Mode 10 ______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs Applications Information External Reference Power consumption can be reduced significantly by placing the MAX1274/MAX1275 in either partial power-down mode or full power-down mode. Partial power-down mode is ideal for infrequent data sampling and fast wakeup time applications. Pull CNVST high after the 3rd SCLK rising edge and before the 14th SCLK rising edge to enter and stay in partial power-down mode (see Figure 6). This reduces the supply current to 1mA. Drive CNVST low and allow at least 14 SCLK cycles to elapse before driving CNVST high to exit partial power-down mode. Full power-down mode is ideal for infrequent data sampling and very low supply current applications. The MAX1274/MAX1275 have to be in partial power-down mode in order to enter full power-down mode. Perform the SCLK/CNVST sequence described above to enter partial power-down mode. Then repeat the same sequence to enter full power-down mode (see Figure 7). Drive CNVST low, and allow at least 14 SCLK cycles to elapse before driving CNVST high to exit full powerdown mode. In partial/full power-down mode, maintain a logic low or a logic high on SCLK to minimize power consumption. An external reference is required for the MAX1274/ MAX1275. Use a 4.7F and 0.01F bypass capacitor on the REF pin for best performance. The reference input structure allows a voltage range of +1V to VDD. How to Start a Conversion An analog-to-digital conversion is initiated by CNVST, clocked by SCLK, and the resulting data is clocked out on DOUT by SCLK. With SCLK idling high or low, a falling edge on CNVST begins a conversion. This causes the analog input stage to transition from track to hold mode, and for DOUT to transition from high impedance to being actively driven low. A total of 16 SCLK cycles are required to complete a normal conversion. If CNVST is low during the 16th falling SCLK edge, DOUT returns to high impedance on the next rising edge of CNVST or SCLK, enabling the serial interface to be shared by multiple devices. If CNVST returns high after the 14th, but before the 16th SCLK rising edge, DOUT remains active so continuous conversions can be sustained. The highest throughput is achieved when performing continuous conversions. Figure 10 illustrates a conversion using a typical serial interface. Transfer Function Figure 8 shows the unipolar transfer function for the MAX1274. Figure 9 shows the bipolar transfer function for the MAX1275. The MAX1274 output is straight binary, while the MAX1275 output is two's complement. EXECUTE PARTIAL POWER-DOWN TWICE CNVST FIRST 8-BIT TRANSFER SECOND 8-BIT TRANSFER SCLK 1ST SCLK RISING EDGE DOUT MODE 0 0 0 DOUT ENTERS TRI-STATE ONCE CNVST GOES HIGH 1ST SCLK RISING EDGE D11 D10 NORMAL D9 D8 0 D7 PPD 0 0 0 0 RECOVERY 0 0 0 FPD Figure 7. SPI Interface--Full Power-Down Mode ______________________________________________________________________________________ 11 MAX1274/MAX1275 Partial Power-Down and Full Power-Down Modes MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs Connection to Standard Interfaces OUTPUT CODE The MAX1274/MAX1275 serial interface is fully compatible with SPI/QSPI and MICROWIRE (see Figure 11). If a serial interface is available, set the CPU's serial interface in master mode so the CPU generates the serial clock. Choose a clock frequency up to 28.8MHz. FULL-SCALE TRANSITION 111...111 111...110 111...101 SPI and MICROWIRE FS = VREF ZS = 0 V 1 LSB = REF 4096 000...011 000...010 000...001 000...000 0 1 2 3 FS DIFFERENTIAL INPUT VOLTAGE (LSB) FS - 3/2 LSB Figure 8. Unipolar Transfer Function (MAX1274 Only) When using SPI or MICROWIRE, the MAX1274/MAX1275 are compatible with all four modes programmed with the CPHA and CPOL bits in the SPI or MICROWIRE control register. Conversion begins with a CNVST falling edge. DOUT goes low, indicating a conversion is in progress. Two consecutive 1-byte reads are required to get the full 12 bits from the ADC. DOUT transitions on SCLK rising edges. DOUT is guaranteed to be valid tDOUT later and remains valid until tDHOLD after the following SCLK rising edge. When using CPOL = 0 and CPHA = 0, or CPOL = 1 and CPHA = 1, the data is clocked into the P on the following rising edge. When using CPOL = 0 and CPHA = 1, or CPOL = 1 and CPHA = 0, the data is clocked into the P on the next falling edge. See Figure 11 for connections and Figures 12 and 13 for timing. See the Timing Characteristics section to determine the best mode to use. QSPI OUTPUT CODE FULL-SCALE TRANSITION V FS = REF 2 ZS = 0 -V - FS = REF 2 V 1 LSB = REF 4096 011...111 011...110 000...010 000...001 Unlike SPI, which requires two 1-byte reads to acquire the 12 bits of data from the ADC, QSPI allows the minimum number of clock cycles necessary to clock in the data. The MAX1274/MAX1275 require 16 clock cycles from the P to clock out the 12 bits of data. Figure 14 shows a transfer using CPOL = 1 and CPHA = 1. The conversion result contains three zeros, followed by the 12 data bits, and a trailing zero with the data in MSBfirst format. 000...000 DSP Interface to the TMS320C54_ 111...111 The MAX1274/MAX1275 can be directly connected to the TMS320C54_ family of DSPs from Texas Instruments, Inc. Set the DSP to generate its own clocks or use external clock signals. Use either the standard or buffered serial port. Figure 15 shows the simplest interface between the MAX1274/MAX1275 and the TMS320C54_, where the transmit serial clock (CLKX) drives the receive serial clock (CLKR) and SCLK, and the transmit frame sync (FSX) drives the receive frame sync (FSR) and CNVST. For continuous conversion, set the serial port to transmit a clock, and pulse the frame sync signal for a clock period before data transmission. The serial-port configuration (SPC) register should be set up with internal 111...110 111...101 100...001 100...000 -FS 0 DIFFERENTIAL INPUT VOLTAGE (LSB) FS FS - 3/2 LSB Figure 9. Bipolar Transfer Function (MAX1275 Only) 12 ______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs MAX1274/MAX1275 CNVST SCLK 1 14 16 1 DOUT 0 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 Figure 10. Continuous Conversion with Burst/Continuous Clock I/O SCK MISO +3V TO +5V CNVST SCLK DOUT MAX1274 MAX1275 SS A) SPI CS SCK MISO +3V TO +5V CNVST SCLK DOUT MAX1274 MAX1275 SS B) QSPI I/O SK SI CNVST SCLK DOUT MAX1274 MAX1275 C) MICROWIRE Figure 11. Common Serial-Interface Connections to the MAX1274/MAX1275 ______________________________________________________________________________________ 13 MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs CNVST 8 1 9 16 SCLK DOUT HIGH-Z D11 D10 D6 D7 D8 D9 D5 D4 D3 D1 D2 HIGH-Z D0 Figure 12. SPI/MICROWIRE Serial-Interface Timing--Single Conversion (CPOL = CPHA = 0), (CPOL = CPHA = 1) CNVST SCLK 14 1 0 DOUT 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 16 D1 D0 1 0 0 Figure 13. SPI/MICROWIRE Serial-Interface Timing--Continuous Conversion (CPOL = CPHA = 0), (CPOL = CPHA = 1) CNVST DOUT 16 2 SCLK HIGH-Z HIGH-Z D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 14. QSPI Serial-Interface Timing--Single Conversion (CPOL = 1, CPHA = 1) frame sync (TXM = 1), CLKX driven by an on-chip clock source (MCM = 1), burst mode (FSM = 1), and 16-bit word length (FO = 0). This setup allows continuous conversions provided that the data transmit register (DXR) and the data-receive register (DRR) are serviced before the next conversion. Alternatively, autobuffering can be enabled when using the buffered serial port to execute conversions and read the data without CPU intervention. Connect the VL pin to the TMS320C54_ supply voltage when the MAX1274/MAX1275 are operating with an analog supply voltage higher than the DSP supply voltage. The 14 word length can be set to 8 bits with FO = 1 to implement the power-down modes. The CNVST pin must idle high to remain in either power-down state. Another method of connecting the MAX1274/MAX1275 to the TMS320C54_ is to generate the clock signals external to either device. This connection is shown in Figure 16, where serial clock (CLOCK) drives the CLKR, and SCLK and the convert signal (CONVERT) drive the FSR and CNVST. The serial port must be set up to accept an external receive-clock and external receive-frame sync. ______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs FSM = 1, burst mode FO = 0, data transmitted/received as 16-bit words This setup allows continuous conversion, provided that the DRR is serviced before the next conversion. Alternatively, autobuffering can be enabled when using the buffered serial port to read the data without CPU VL DSP Interface to the ADSP21_ _ _ DVDD MAX1274 SCLK MAX1275 The MAX1274/MAX1275 can be directly connected to the ADSP21_ _ _ family of DSPs from Analog Devices, Inc. Figure 19 shows the direct connection of the MAX1274/MAX1275 to the ADSP21_ _ _. There are two modes of operation that can be programmed to interface with the MAX1274/MAX1275. For continuous conversions, idle CNVST low and pulse it high for one clock cycle during the LSB of the previous transmitted word. The ADSP21_ _ _ STCTL and SRCTL registers should be configured for early framing (LAFR = 0) and for an active-high frame (LTFS = 0, LRFS = 0) signal. In this mode, the data-independent frame-sync bit (DITFS = 1) can be selected to eliminate the need for writing to the transmit-data register more than once. For single conversions, idle CNVST high and pulse it low for the entire conversion. The ADSP21_ _ _ STCTL and SRCTL registers should be configured for late framing (LAFR = 1) and for an active-low frame (LTFS = 1, LRFS = 1) signal. This is also the best way to enter the power-down modes by setting the word length to 8 bits (SLEN = 1001). Connect the VL pin to the ADSP21_ _ _ supply voltage when the MAX1274/MAX1275 are operating with a supply voltage higher than the DSP supply voltage (see Figures 17 and 18). CLKX TMS320C54_ CLKR CNVST FSX FSR DOUT DR Figure 15. Interfacing to the TMS320C54_ Internal Clocks VL DVDD MAX1274 MAX1275 SCLK CLKR TMS320C54_ CNVST FSR DOUT DR intervention. Connect the VL pin to the TMS320C54_ supply voltage when the MAX1274/ MAX1275 are operating with an analog supply voltage higher than the DSP supply voltage. The MAX1274/MAX1275 can also be connected to the TMS320C54_ by using the data transmit (DX) pin to drive CNVST and the CLKX generated internally to drive SCLK. A pullup resistor is required on the CNVST signal to keep it high when DX goes high impedance and 0001hex should be written to the DXR continuously for continuous conversions. The power-down modes may be entered by writing 00FFhex to the DXR (see Figures 17 and 18). CLOCK CONVERT Figure 16. Interfacing to the TMS320C54_ External Clocks CNVST SCLK DOUT 1 D0 0 1 0 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 Figure 17. DSP Interface--Continuous Conversion ______________________________________________________________________________________ 15 MAX1274/MAX1275 The SPC register should be written as follows: TXM = 0, external frame sync MCM = 0, CLKX is taken from the CLKX pin MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs CNVST SCLK 1 DOUT 1 0 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 Figure 18. DSP Interface--Single-Conversion, Continuous/Burst Clock VL VDDINT MAX1274 SCLK MAX1275 TCLK ADSP21_ _ _ RCLK CNVST TFS RFS DOUT DR Figure 19. Interfacing to the ADSP21_ _ _ Figure 20 shows the recommended system ground connections. Establish a single-point analog ground (star ground point) at GND, separate from the logic ground. Connect all other analog grounds and DGND to this star ground point for further noise reduction. The ground return to the power supply for this ground should be low impedance and as short as possible for noise-free operation. High-frequency noise in the VDD power supply can affect the ADC's high-speed comparator. Bypass this supply to the single-point analog ground with 0.01F and 10F bypass capacitors. Minimize capacitor lead lengths for best supply-noise rejection. Definitions Integral Nonlinearity SUPPLIES GND VL 10F 10F 0.1F 0.1F VDD Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a straight line. This straight line can be either a best-straight-line fit or a line drawn between the end points of the transfer function, once offset and gain errors have been nullified. The static linearity parameters for the MAX1274/MAX1275 are measured using the end-points method. Differential Nonlinearity GND RGND VL MAX1274 MAX1275 DGND VL DIGITAL CIRCUITRY Differential nonlinearity (DNL) is the difference between an actual step width and the ideal value of 1 LSB. A DNL error specification of 1 LSB or less guarantees no missing codes and a monotonic transfer function. Aperture Jitter Aperture jitter (tAJ) is the sample-to-sample variation in the time between the samples. Figure 20. Power-Supply Grounding Condition Aperture Delay Layout, Grounding, and Bypassing For best performance, use PC boards. Wire-wrap boards are not recommended. Board layout should ensure that digital and analog signal lines are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the ADC package. 16 Aperture delay (tAD) is the time defined between the falling edge of CNVST and the instant when an actual sample is taken. ______________________________________________________________________________________ 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs SNR = (6.02 x N + 1.76)dB In reality, there are other noise sources besides quantization noise, including thermal noise, reference noise, clock jitter, etc. Therefore, SNR is computed by taking the ratio of the RMS signal to the RMS noise, which includes all spectral components minus the fundamental, the first five harmonics, and the DC offset. Signal-to-Noise Plus Distortion Signal-to-noise plus distortion (SINAD) is the ratio of the fundamental input frequency's RMS amplitude to the RMS equivalent of all other ADC output signals: SINAD(dB) = 20 x log (SignalRMS / NoiseRMS) Effective Number of Bits Effective number of bits (ENOB) indicates the global accuracy of an ADC at a specific input frequency and sampling rate. An ideal ADC's error consists of quantization noise only. With an input range equal to the full-scale range of the ADC, calculate the ENOB as follows: ENOB = (SINAD - 1.76) 6.02 Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the RMS sum of the first five harmonics of the input signal to the fundamental itself. This is expressed as: V22 + V32 + V42 + V52 THD = 20 x log V1 where V 1 is the fundamental amplitude, and V 2 through V5 are the amplitudes of the 2nd- through 5thorder harmonics. Spurious-Free Dynamic Range Spurious-free dynamic range (SFDR) is the ratio of the RMS amplitude of the fundamental (maximum signal component) to the RMS value of the next largest distortion component. Full-Power Bandwidth Full-power bandwidth is the frequency at which the input signal amplitude attenuates by 3dB for a full-scale input. Full-Linear Bandwidth Full-linear bandwidth is the frequency at which the signal to noise plus distortion (SINAD) is equal to 68dB. Intermodulation Distortion (IMD) Any device with nonlinearities creates distortion products when two sine waves at two different frequencies (f1 and f2) are input into the device. Intermodulation distortion (IMD) is the total power of the IM2 to IM5 intermodulation products to the Nyquist frequency relative to the total input power of the two input tones, f1 and f2. The individual input tone levels are at -7dBFS. The intermodulation products are as follows: * 2nd-order intermodulation products (IM2): f1 + f2, f2 - f1 * 3rd-order intermodulation products (IM3): 2f 1 - f2, 2f2 - f1, 2f1 + f2, 2f2 + f1 * 4th-order intermodulation products (IM4): 3f 1 - f2, 3f2 - f1, 3f1 + f2, 3f2 + f1 * 5th-order intermodulation products (IM5): 3f1 - 2f2, 3f2 - 2f1, 3f1 + 2f2, 3f2 + 2f1 Chip Information TRANSISTOR COUNT: 13,016 PROCESS: BiCMOS ______________________________________________________________________________________ 17 MAX1274/MAX1275 Signal-to-Noise Ratio For a waveform perfectly reconstructed from digital samples, signal-to-noise ratio (SNR) is the ratio of the fullscale analog input (RMS value) to the RMS quantization error (residual error). The theoretical minimum analog-todigital noise is caused by quantization error, and results directly from the ADC's resolution (N bits): Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 24L QFN THIN.EPS MAX1274/MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs PACKAGE OUTLINE 12,16,20,24L QFN THIN, 4x4x0.8 mm 21-0139 B 1 2 PACKAGE OUTLINE 12,16,20,24L QFN THIN, 4x4x0.8 mm 21-0139 B 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. ENGLISH * ???? * ??? * ??? WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS M axim > P roduc ts > A nalog-to-Digital C onverters MAX1274, MAX1275 1.8Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADC s QuickView Technical Documents Ordering Info More Information All Ordering Information Notes: 1. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales. 2. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day. 3. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: SeeFull Data Sheet or Part Naming C onventions. 4. * Some packages have variations, listed on the drawing. "PkgC ode/Variation" tells which variation the product uses. Devices: 1-10 of 10 M AX1274 Fre e Sam ple Buy Pack age : TYPE PINS FOOTPRINT Tem p DRAWING CODE/VAR * RoHS/Le ad-Free ? M aterials Analys is MAX1274C TC 0C to +70C RoHS/Lead-Free: See data sheet MAX1274ETC -40C to +85C RoHS/Lead-Free: See data sheet MAX1274BC TC -T THIN QFN;12 pin;17 mm Dwg: 21-0139G (PDF) Use pkgcode/variation: T1244-3* RoHS/Lead-Free: No Materials Analysis MAX1274BC TC THIN QFN;12 pin;17 mm Dwg: 21-0139G (PDF) Use pkgcode/variation: T1244-3* RoHS/Lead-Free: No Materials Analysis MAX1274BETC THIN QFN;12 pin;17 mm -40C to +85C RoHS/Lead-Free: No Dwg: 21-0139G (PDF) Materials Analysis Use pkgcode/variation: T1244-3* MAX1274BETC -T THIN QFN;12 pin;17 mm -40C to +85C RoHS/Lead-Free: No Dwg: 21-0139G (PDF) Materials Analysis Use pkgcode/variation: T1244-3* M AX1275 Fre e Sam ple Buy Pack age : TYPE PINS FOOTPRINT Tem p DRAWING CODE/VAR * RoHS/Le ad-Free ? M aterials Analys is MAX1275C TC 0C to +70C RoHS/Lead-Free: See data sheet MAX1275ETC -40C to +85C RoHS/Lead-Free: See data sheet MAX1275BC TC THIN QFN;12 pin;17 mm Dwg: 21-0139G (PDF) Use pkgcode/variation: T1244-3* RoHS/Lead-Free: No Materials Analysis MAX1275BC TC -T THIN QFN;12 pin;17 mm Dwg: 21-0139G (PDF) Use pkgcode/variation: T1244-3* RoHS/Lead-Free: No Materials Analysis Didn't Find What You Need? Next Day Product Selection Assistance from Applications Engineers Parametric Search Applications Help QuickView Technical Documents Ordering Info More Information Des c ription Key Features A pplic ations /U s es Key Spec ific ations Diagram Data Sheet A pplic ation N otes Des ign Guides E ngineering Journals Reliability Reports Software/M odels E valuation Kits P ric e and A vailability Samples Buy O nline P ac kage I nformation Lead-Free I nformation Related P roduc ts N otes and C omments E valuation Kits Doc ument Ref.: 1 9 -3 1 5 8 ; Rev 0 ; 2 0 0 4 -0 2 -1 8 T his page las t modified: 2 0 0 7 -0 8 -2 8 C ONTAC T US: SEND US AN EMAIL C opyright 2 0 0 7 by M axim I ntegrated P roduc ts , Dallas Semic onduc tor * Legal N otic es * P rivac y P olic y