S-93L46A/56A/66A LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM www.sii-ic.com Rev.7.0_00 (c) Seiko Instruments Inc., 2004-2011 The S-93L46A/56A/66A is a low voltage operation, high speed, low current consumption, 3-wire serial E2PROM with a wide operating voltage range. The S-93L46A/56A/66A has the capacity of 1 K-bit, 2 K-bit and 4 K-bit, and the organization is 64word x 16-bit, 128-word x 16-bit, and 256-word x 16-bit. It is capable of sequential read, at which time addresses are automatically incremented in 16-bit blocks. The communication method is by the Microwire bus. Features * Operating voltage range Read: Write: 1.6 V to 5.5 V 1.8 V to 5.5 V (WRITE, ERASE) 2.7 V to 5.5 V (WRAL, ERAL) 2.0 MHz (VCC = 4.5 V to 5.5 V) 8.0 ms max. * Operation frequency: * Write time: * Sequential read capable * Write protect function during the low power supply voltage * Function to protect against write due to erroneous instruction recognition * Endurance: 106 cycles / word*1 (Ta = +85C) * Data retention: 100 years (Ta = +25C) 20 years (Ta = +85C) * Memory capacity: S-93L46A: 1 K-bit S-93L56A: 2 K-bit S-93L66A: 4 K-bit * Initial shipment data: FFFFh * Lead-free, Sn 100%, halogen-free*2 *1. For each address (Word: 16-bit) *2. Refer to " Product Name Structure" for details. Packages * 8-Pin SOP (JEDEC) * 8-Pin TSSOP * TMSOP-8 * SNT-8A * WLP-7D Caution This product is intended to use in general electronic devices such as consumer electronics, office equipment, and communications devices. Before using the product in medical equipment or automobile equipment including car audio, keyless entry and engine control unit, contact to SII is indispensable. Seiko Instruments Inc. 1 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Pin Configurations 1. 8-Pin SOP (JEDEC) 8-Pin SOP (JEDEC) Top view Table 1 Pin No. 1 8 2 7 3 6 4 5 Symbol Figure 1 S-93L46AD0I-J8T1x S-93L56AD0I-J8T1x S-93L66AD0I-J8T1x 8-Pin SOP (JEDEC) (Rotated) Top view Table 2 Pin No. 1 8 2 7 3 6 4 5 Figure 2 S-93L46AR0I-J8T1x S-93L56AR0I-J8T1x S-93L66AR0I-J8T1x 2 Description 1 CS Chip select input 2 SK Serial clock input 3 DI Serial data input 4 DO Serial data output 5 GND Ground TEST*1 6 Test 7 NC No connection 8 VCC Power supply *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. Symbol Description 1 NC No connection 2 VCC Power supply 3 CS Chip select input 4 SK Serial clock input 5 DI Serial data input 6 DO Serial data output 7 GND Ground TEST*1 8 Test *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 2. 8-Pin TSSOP 8-Pin TSSOP Top view Table 3 Pin No. 1 2 3 4 8 7 6 5 Figure 3 S-93L46AD0I-T8T1x S-93L56AD0I-T8T1x S-93L66AD0I-T8T1x 3. Symbol Description 1 CS Chip select input 2 SK Serial clock input 3 DI Serial data input 4 DO Serial data output 5 GND Ground TEST*1 6 Test 7 NC No connection 8 VCC Power supply *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. TMSOP-8 TMSOP-8 Top view Table 4 Pin No. 1 2 3 4 8 7 6 5 Figure 4 S-93L46AD0I-K8T3U S-93L56AD0I-K8T3U S-93L66AD0I-K8T3U Symbol Description 1 CS Chip select input 2 SK Serial clock input 3 DI Serial data input 4 DO Serial data output 5 GND Ground TEST*1 6 Test 7 NC No connection 8 VCC Power supply *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. Seiko Instruments Inc. 3 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 4. SNT-8A SNT-8A Top view Table 5 Pin No. 1 2 3 4 8 7 6 5 Figure 5 S-93L46AD0I-I8T1x S-93L56AD0I-I8T1x S-93L66AD0I-I8T1x 5. Rev.7.0_00 Symbol Description 1 CS Chip select input 2 SK Serial clock input 3 DI Serial data input 4 DO Serial data output 5 GND Ground TEST*1 6 Test 7 NC No connection 8 VCC Power supply *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. WLP-7D WLP-7D Bottom view Table 6 Pin No. 4 3 TEST 5 VCC GND 2 DI 6 1 7 CS DO SK Figure 6 Symbol Description 1 CS Chip select input 2 DI Serial data input 3 VCC Power supply TEST*1 4 Test 5 GND Ground 6 DO Serial data output 7 SK Serial clock input *1. Connect to GND or VCC. Even if this pin is not connected, performance is not affected so long as the absolute maximum rating is not exceeded. S-93L66AD0I-H7T4S Remark 1. Refer to the "Package drawings" for the details. 2. x: G or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 4 Seiko Instruments Inc. Rev.7.0_00 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Block Diagram Memory array VCC Address decoder Data register GND Output buffer DO DI Mode decode logic CS Clock pulse monitoring circuit SK Voltage detector Clock generator Figure 7 Seiko Instruments Inc. 5 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Instruction Sets 1. S-93L46A Table 7 Instruction SK input clock Start Bit Address 4 5 6 7 Data 10 to 25 D15 to D0 Output*1 READ (Read data) 1 1 0 A5 A4 A3 A2 A1 A0 WRITE (Write data) 1 0 1 A5 A4 A3 A2 A1 A0 D15 to D0 Input ERASE (Erase data) 1 1 1 A5 A4 A3 A2 A1 A0 WRAL (Write all) 1 0 0 0 1 x x x x D15 to D0 Input ERAL (Erase all) 1 0 0 1 0 x x x x EWEN (Write enable) 1 0 0 1 1 x x x x EWDS (Write disable) 1 0 0 0 0 x x x x *1. When the 16-bit data in the specified address has been output, the data in the next address is output. Remark x: Don't care 2. 1 Operation Code 2 3 8 9 S-93L56A Table 8 Instruction SK input clock Start Bit Operation Code Address Data 1 2 3 4 5 6 7 8 9 10 11 12 to 27 D15 to D0 Output*1 READ (Read data) 1 1 0 x A6 A5 A4 A3 A2 A1 A0 WRITE (Write data) 1 0 1 x A6 A5 A4 A3 A2 A1 A0 D15 to D0 Input ERASE (Erase data) 1 1 1 x A6 A5 A4 A3 A2 A1 A0 WRAL (Write all) 1 0 0 0 1 x x x x x x D15 to D0 Input ERAL (Erase all) 1 0 0 1 0 x x x x x x EWEN (Write enable) 1 0 0 1 1 x x x x x x EWDS (Write disable) 1 0 0 0 0 x x x x x x *1. When the 16-bit data in the specified address has been output, the data in the next address is output. Remark x: Don't care 3. S-93L66A Table 9 Operation Address Data Start Bit Code 1 2 3 4 5 6 7 8 9 10 11 12 to 27 D15 to D0 Output*1 READ (Read data) 1 1 0 A7 A6 A5 A4 A3 A2 A1 A0 WRITE (Write data) 1 0 1 A7 A6 A5 A4 A3 A2 A1 A0 D15 to D0 Input ERASE (Erase data) 1 1 1 A7 A6 A5 A4 A3 A2 A1 A0 WRAL (Write all) 1 0 0 0 1 x x x x x x D15 to D0 Input ERAL (Erase all) 1 0 0 1 0 x x x x x x EWEN (Write enable) 1 0 0 1 1 x x x x x x EWDS (Write disable) 1 0 0 0 0 x x x x x x *1. When the 16-bit data in the specified address has been output, the data in the next address is output. Remark x: Don't care Instruction SK input clock 6 Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Absolute Maximum Ratings Table 10 Item Symbol Ratings Unit Power supply voltage VCC -0.3 to +7.0 V Input voltage VIN -0.3 to VCC + 0.3 V Output voltage VOUT -0.3 to VCC V Operating ambient temperature Topr -40 to +85 C Storage temperature Tstg -65 to +150 C Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Recommended Operating Conditions Table 11 Item Symbol Power supply voltage VCC High level input voltage VIH Low level input voltage VIL Ta = -40C to +85C Min. Max. Conditions READ, EWDS WRITE, ERASE, EWEN WRAL, ERAL VCC = 4.5 V to 5.5 V VCC = 2.7 V to 4.5 V VCC = 1.6 V to 2.7 V VCC = 4.5 V to 5.5 V VCC = 2.7 V to 4.5 V VCC = 1.6 V to 2.7 V 1.6 1.8 2.7 2.0 0.8 x VCC 0.8 x VCC 0.0 0.0 0.0 Unit 5.5 5.5 5.5 VCC VCC VCC 0.8 0.2 x VCC 0.15 x VCC V V V V V V V V V Pin Capacitance Table 12 Item Input Capacitance Output Capacitance Symbol CIN COUT Ta = +25C, f = 1.0 MHz, VCC = 5.0 V) Min. Max. Unit 8 pF 10 pF Conditions VIN = 0 V VOUT = 0 V Endurance Table 13 Item Endurance Symbol Operating Ambient Temperature Ta = -40C to +85C NW Min. 6 10 Max. Unit Cycles / word*1 Max. Unit year year *1. For each address (Word: 16-bit) Data Retention Table 14 Item Data Retention Symbol Operating Ambient Temperature Ta = +25C Ta = -40C to +85C Seiko Instruments Inc. Min. 100 20 7 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 DC Electrical Characteristics Table 15 Item Symbol Current consumption ICC1 (READ) Conditions VCC = 4.5 V to 5.5 V Min. Max. DO no load Ta = -40C to +85C VCC = 2.5 V to 4.5 V Min. Max. VCC = 1.6 V to 2.5 V Max. Min. Unit 0.4 mA Ta = -40C to +85C VCC = 4.5 V to 5.5 V VCC = 1.8 V to 4.5 V Min. Max. Min. Max. Unit 0.8 0.5 Table 16 Item Symbol Current consumption ICC2 (WRITE) Conditions DO no load 2.0 1.5 mA Table 17 Item Standby current consumption Input leakage current Output leakage current Low level output voltage Symbol Conditions Ta = -40C to +85C VCC = 2.5 V to 4.5 V Min. Max. VCC = 1.6 V to 2.5 V Max. Min. Unit ISB CS = GND, DO = Open, Other inputs to VCC or GND 1.5 1.5 1.5 A ILI VIN = GND to VCC 1.0 1.0 1.0 A ILO VOUT = GND to VCC 1.0 1.0 1.0 A 2.4 VCC - 0.3 VCC - 0.2 0.4 0.1 VCC - 0.3 VCC - 0.2 0.1 VCC - 0.2 0.1 V V V V V 1.5 1.5 1.5 V VOL High level output voltage VOH Write enable latch data hold voltage VDH 8 VCC = 4.5 V to 5.5 V Min. Max. IOL = 2.1 mA IOL = 100 A IOH = -400 A IOH = -100 A IOH = -10 A Only when write disable mode Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 AC Electrical Characteristics Table 18 Measurement Conditions 0.1 x VCC to 0.9 x VCC 0.5 x VCC 100 pF Input pulse voltage Output reference voltage Output load Table 19 Ta = -40C to +85C VCC = 4.5 V to 5.5 V VCC = 2.5 V to 4.5 V VCC = 1.6 V to 2.5 V Unit Max. Min. Max. Min. Max. Min. CS setup time tCSS 0.2 -- 0.4 -- 1.0 -- s CS hold time tCSH 0 -- 0 -- 0 -- s CS deselect time tCDS 0.2 -- 0.2 -- 0.4 -- s Data setup time tDS 0.1 -- 0.2 -- 0.4 -- s Data hold time tDH 0.1 -- 0.2 -- 0.4 -- s Output delay time tPD -- 0.4 -- 0.8 -- 2.0 s *1 Clock frequency 0 2.0 0 1.0 0 0.25 MHz fSK SK clock time "L" *1 0.1 -- 0.25 -- 1.0 -- s tSKL *1 SK clock time "H" 0.1 -- 0.25 -- 1.0 -- s tSKH Output disable time tHZ1, tHZ2 0 0.15 0 0.5 0 1.0 s Output enable time tSV 0 0.15 0 0.5 0 1.0 s *1. The clock cycle of the SK clock (frequency: fSK) is 1 / fSK s. This clock cycle is determined by a combination of several AC characteristics, so be aware that even if the SK clock cycle time is minimized, the clock cycle (1 / fSK) cannot be made equal to tSKL (min.) + tSKH (min.). Item Symbol Table 20 Item Write time Symbol tPR Ta = -40C to +85C VCC = 1.8 to 5.5 V Min Typ. Max. -- 4.0 8.0 Seiko Instruments Inc. Unit ms 9 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 *2 tCSS tCDS 1 / fSK CS tSKH tSKL tCSH SK tDS DI tDS tDH tDH Valid data Valid data tPD tPD *1 High-Z High-Z DO tSV (READ) DO High-Z tHZ1 tHZ2 High-Z (VERIFY) *1. *2. Indicates high impedance. 1 / fSK is the SK clock cycle. This clock cycle is determined by a combination of several AC characteristics, so be aware that even if the SK clock cycle time is minimized, the clock cycle (1 / fSK) cannot be made equal to tSKL (min.) + tSKH (min.). Figure 8 10 Timing Chart Seiko Instruments Inc. Rev.7.0_00 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Initial Shipment Data Initial shipment data of all adresses is "FFFFh". Operation All instructions are executed by inputting DI in synchronization with the rising edge of SK after CS goes high. An instruction set is input in the order of start bit, instruction, address, and data. Instruction input finishes when CS goes low. A low level must be input to CS between commands during tCDS. While a low level is being input to CS, the S-93L46A/56A/66A is in standby mode, so the SK and DI inputs are invalid and no instructions are allowed. Start Bit A start bit is recognized when the DI pin goes high at the rise of SK after CS goes high. After CS goes high, a start bit is not recognized even if the SK pulse is input as long as the DI pin is low. 1. Dummy clock SK clocks input while the DI pin is low before a start bit is input are called dummy clocks. Dummy clocks are effective when aligning the number of instruction sets (clocks) sent by the CPU with those required for serial memory operation. For example, when a CPU instruction set is 16 bits, the number of instruction set clocks can be adjusted by inserting a 7-bit dummy clock for the S-93L46A and a 5-bit dummy clock for the S-93L56A/66A. 2. Start bit input failure * When the output status of the DO pin is high during the verify period after a write operation, if a high level is input to the DI pin at the rising edge of SK, the S-93L46A/56A/66A recognizes that a start bit has been input. To prevent this failure, input a low level to the DI pin during the verify operation period (refer to "4. 1 Verify operation"). * When a 3-wire interface is configured by connecting the DI input pin and DO output pin, a period in which the data output from the CPU and the serial memory collide may be generated, preventing successful input of the start bit. Take the measures described in " 3-Wire Interface (Direct Connection between DI and DO)". Seiko Instruments Inc. 11 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 3. Rev.7.0_00 Reading (READ) The READ instruction reads data from a specified address. After CS has gone high, input an instruction in the order of the start bit, read instruction, and address. Since the last input address (A0) has been latched, the output status of the DO pin changes from high impedance (High-Z) to low, which is held until the next rise of SK. 16-bit data starts to be output in synchronization with the next rise of SK. 3. 1 Sequential read After the 16-bit data at the specified address has been output, inputting SK while CS is high automatically increments the address, and causes the 16-bit data at the next address to be output sequentially. The above method makes it possible to read the data in the whole memory space. The last address (An yyy A1 A0 = 1 yyy 1 1) rolls over to the top address (An yyy A1 A0 = 0 yyy 0 0). CS SK 1 DI 2 <1> 1 3 0 4 A5 5 A4 6 A3 7 A2 8 A1 10 9 11 12 23 24 25 26 27 28 39 40 41 42 43 44 A0 High-Z DO 0 D15 D14 D13 D2 D1 D0 D15 D14 D13 D2 D1 ADRINC Figure 9 D0 D15 D14 D13 High-Z ADRINC Read Timing (S-93L46A) CS SK DI 1 <1> 2 1 3 4 0 5 A6 6 7 8 9 A5 A4 A3 A2 10 A1 11 12 13 14 24 25 26 27 28 29 40 41 42 43 44 45 A0 x: S-93L56A DO High-Z A7: S-93L66A 0 D15 D14 D13 D2 D1 D0 D15 D14 D13 ADRINC Figure 10 12 Read Timing (S-93L56A, S-93L66A) Seiko Instruments Inc. D2 D1 D0 D15 D14 D13 ADRINC High-Z Rev.7.0_00 4. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Writing (WRITE, ERASE, WRAL, ERAL) A write operation includes four write instructions: data write (WRITE), data erase (ERASE), chip write (WRAL), and chip erase (ERAL). A write instruction (WRITE, ERASE, WRAL, ERAL) starts a write operation to the memory cell when a low level is input to CS after a specified number of clocks have been input. The SK and DI inputs are invalid during the write period, so do not input an instruction. Input an instruction while the output status of the DO pin is high or high impedance (High-Z). A write operation is valid only in program enable mode (refer to "5. Write enable (EWEN) and write disable (EWDS)"). 4. 1 Verify operation A write operation executed by any instruction is completed within 8 ms (write time tPR: typically 4 ms), so if the completion of the write operation is recognized, the write cycle can be minimized. A sequential operation to confirm the status of a write operation is called a verify operation. 4. 1. 1 Operation After the write operation has started (CS = low), the status of the write operation can be verified by confirming the output status of the DO pin by inputting a high level to CS again. This sequence is called a verify operation, and the period that a high level is input to the CS pin after the write operation has started is called the verify operation period. The relationship between the output status of the DO pin and the write operation during the verify operation period is as follows. * DO pin = low: Writing in progress (busy) * DO pin = high: Writing completed (ready) 4. 1. 2 Operation example There are two methods to perform a verify operation: Waiting for a change in the output status of the DO pin while keeping CS high, or suspending the verify operation (CS = low) once and then performing it again to verify the output status of the DO pin. The latter method allows the CPU to perform other processing during the wait period, allowing an efficient system to be designed. Caution 1. Input a low level to the DI pin during a verify operation. 2. If a high level is input to the DI pin at the rise of SK when the output status of the DO pin is high, the S-93L46A/56A/66A latches the instruction assuming that a start bit has been input. In this case, note that the DO pin immediately enters a high-impedance (High-Z) state. Seiko Instruments Inc. 13 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 4. 2 Rev.7.0_00 Writing data (WRITE) To write 16-bit data to a specified address, change CS to high and then input the WRITE instruction, address, and 16-bit data following the start bit. The write operation starts when CS goes low. There is no need to set the data to 1 before writing. If the clocks more than the specified number have been input, the clock pulse monitoring circuit cancels the WRITE instruction. For details of the clock pulse monitoring circuit, refer to " Function to Protect Against Write due to Erroneous Instruction Recognition". tCDS CS Standby Verify SK 1 DI <1> 2 0 3 1 4 5 6 7 8 9 10 A5 A4 A3 A2 A1 A0 D15 25 D0 tSV tHZ1 High-Z DO Busy Ready High-Z tPR Figure 11 Data Write Timing (S-93L46A) tCDS CS SK DI Standby Verify 1 2 <1> 0 3 1 4 5 6 7 8 9 10 11 12 27 A6 A5 A4 A3 A2 A1 A0 D15 D0 tSV DO x : S-93L56A A7: S-93L66A Figure 12 14 tHZ1 High-Z Data Write Timing (S-93L56A, S-93L66A) Seiko Instruments Inc. Busy tPR Ready High-Z LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 4. 3 Erasing data (ERASE) To erase 16-bit data at a specified address, set all 16 bits of the data to 1, change CS to high, and then input the ERASE instruction and address following the start bit. There is no need to input data. The data erase operation starts when CS goes low. If the clocks have been input more than the specified number, the clock pulse monitoring circuit cancels the ERASE instruction. For details of the clock pulse monitoring circuit, refer to " Function to Protect Against Write due to Erroneous Instruction Recognition". tCDS CS Standby Verify SK 1 2 DI <1> 1 3 1 4 5 6 7 8 A5 A4 A3 A2 A1 9 A0 tSV tHZ1 High-Z DO Busy Ready High-Z tPR Figure 13 Data Erase Timing (S-93L46A) tCDS CS Standby Verify SK 1 2 DI <1> 1 3 4 1 5 6 7 8 9 A6 A5 A4 A3 A2 10 A1 11 A0 tSV tHZ1 High-Z DO x : S-93L56A A7: S-93L66A Figure 14 Busy tPR Ready High-Z Data Erase Timing (S-93L56A, S-93L66A) Seiko Instruments Inc. 15 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 4. 4 Rev.7.0_00 Writing to chip (WRAL) To write the same 16-bit data to the entire memory address space, change CS to high, and then input the WRAL instruction, an address, and 16-bit data following the start bit. Any address can be input. The write operation starts when CS goes low. There is no need to set the data to 1 before writing. If the clocks more than the specified number have been input, the clock pulse monitoring circuit cancels the WRAL instruction. For details of the clock pulse monitoring circuit, refer to " Function to Protect Against Write due to Erroneous Instruction Recognition". tCDS CS Standby Verify SK 1 2 DI <1> 0 3 0 4 0 5 6 7 9 1 10 25 D0 D15 tSV 4Xs High-Z DO 8 tHZ1 Busy Ready High-Z tPR Figure 15 Chip Write Timing (S-93L46A) tCDS CS SK 1 2 DI <1> 0 DO 3 0 4 0 5 6 7 8 9 10 11 1 High-Z 12 27 D15 D0 6Xs tSV tHZ1 Busy tPR Figure 16 16 Standby Verify Chip Write Timing (S-93L56A, S-93L66A) Seiko Instruments Inc. Ready High-Z LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 4. 5 Erasing chip (ERAL) To erase the data of the entire memory address space, set all the data to 1, change CS to high, and then input the ERAL instruction and an address following the start bit. Any address can be input. There is no need to input data. The chips erase operation starts when CS goes low. When the clocks more than the specified number have been input, the clock pulse monitoring circuit cancels the ERAL instruction. For details of the clock pulse monitoring circuit, refer to " Function to Protect Against Write due to Erroneous Instruction Recognition". CS SK 1 2 3 4 DI <1> 0 0 1 5 6 7 8 9 0 4Xs tHZ1 tSV High-Z DO Standby Verify tCDS Busy Ready High-Z tPR Figure 17 Chip Erase Timing (S-93L46A) CS SK 1 2 3 4 DI <1> 0 0 1 5 6 7 8 9 11 0 6Xs DO 10 Standby Verify tCDS tHZ1 tSV High-Z Busy Ready High-Z tPR Figure 18 Chip Erase Timing (S-93L56A, S-93L66A) Seiko Instruments Inc. 17 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 5. Rev.7.0_00 Write enable (EWEN) and write disable (EWDS) The EWEN instruction is an instruction that enables a write operation. The status in which a write operation is enabled is called the program enable mode. The EWDS instruction is an instruction that disables a write operation. The status in which a write operation is disabled is called the program disable mode. After CS goes high, input an instruction in the order of the start bit, EWEN or EWDS instruction, and address (optional). Each mode becomes valid by inputting a low level to CS after the last address (optional) has been input. Standby CS SK 1 DI <1> 2 3 4 5 6 7 8 9 0 0 11 = EWEN 00 = EWDS Figure 19 4Xs Write Enable / Disable Timing (S-93L46A) CS Standby SK 1 DI <1> 2 0 3 4 5 Figure 20 18 7 8 9 10 11 0 11 = EWEN 00 = EWDS 5. 1 6 6Xs Write Enable / Disable Timing (S-93L56A, S-93L66A) Recommendation for write operation disable instruction It is recommended to implement a design that prevents an incorrect write operation when a write instruction is erroneously recognized by executing the write operation disable instruction when executing instructions other than write instruction, and immediately after power-on and before power off. Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Write Protect Function during the Low Power Supply Voltage The S-93L46A/56A/66A provides a built-in detector to detect a low power supply voltage and disable writing. When the power supply voltage is low or at power application, the write instructions (WRITE, ERASE, WRAL, and ERAL) are cancelled, and the write disable state (EWDS) is automatically set. The detection voltage and the release voltage are 1.4 V typ. (refer to Figure 21). Therefore, when a write operation is performed after the power supply voltage has dropped and then risen again up to the level at which writing is possible, a write enable instruction (EWEN) must be sent before a write instruction (WRITE, ERASE, WRAL, or ERAL) is executed. When the power supply voltage drops during a write operation, the data being written to an address at that time is not guaranteed. Power supply Detection voltage (-VDET) 1.4 V typ. Release voltage (+VDET) 1.4 V typ. Write instruction cancelled Write disable state (EWDS) automatically set Figure 21 Operation during Low Power Supply Voltage Seiko Instruments Inc. 19 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Function to Protect Against Write due to Erroneous Instruction Recognition The S-93L46A/56A/66A provides a built-in clock pulse monitoring circuit which is used to prevent an erroneous write operation by canceling write instructions (WRITE, ERASE, WRAL, and ERAL) recognized erroneously due to an erroneous clock count caused by the application of noise pulses or double counting of clocks. Instructions are cancelled if a clock pulse more or less than specified number decided by each write operation (WRITE, ERASE, WRAL, or ERAL) is detected. <Example> Erroneous recognition of program disable instruction (EWDS) as erase instruction (ERASE) Example of S-93L46A Noise pulse CS 1 2 3 4 5 6 7 8 9 SK DI Input EWDS instruction 1 0 0 0 0 0 0 0 0 Erroneous recognition as ERASE instruction due to noise pulse 1 1 10 0 0 00 0 0 0 0 In products that do not include a clock pulse monitoring circuit, FFFF is mistakenly written on address 00h. However the S-93L46A detects the overcount and cancels the instruction without performing a write operation. Figure 22 20 Example of Clock Pulse Monitoring Circuit Operation Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 3-Wire Interface (Direct Connection between DI and DO) There are two types of serial interface configurations: a 4-wire interface configured using the CS, SK, DI, and DO pins, and a 3-wire interface that connects the DI input pin and DO output pin. When the 3-wire interface is employed, a period in which the data output from the CPU and the data output from the serial memory collide may occur, causing a malfunction. To prevent such a malfunction, connect the DI and DO pins of the S-93L46A/56A/66A via a resistor (10 k to 100 k) so that the data output from the CPU takes precedence in being input to the DI pin (refer to Figure 23). CPU S-93L46A/56A/66A SIO DI DO R: 10 k to 100 k Figure 23 Connection of 3-Wire Interface Input Pin and Output Pin 1. Connection of input pins All the input pins of the S-93L46A/56A/66A employ a CMOS structure, so design the equipment so that high impedance will not be input while the S-93L46A/56A/66A is operating. Especially, deselect the CS input (a low level) when turning on / off power and during standby. When the CS pin is deselected (a low level), incorrect data writing will not occur. Connect the CS pin to GND via a resistor (10 k to 100 k pull-down resistor). To prevent malfunction, it is recommended to use equivalent pull-down resistors for pins other than the CS pin. 2. Equivalent circuit of input pin and output pin The following shows the equivalent circuits of input pins of the S-93L46A/56A/66A. None of the input pins incorporate pull-up and pull-down elements, so special care must be taken when designing to prevent a floating status. Output pins are high-level / low-level / high-impedance tri-state outputs. The TEST pin is disconnected from the internal circuit by a switching transistor during normal operation. As long as the absolute maximum rating is satisfied, the TEST pin and internal circuit will never be connected. Seiko Instruments Inc. 21 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 2. 1 Input pin CS Figure 24 CS Pin SK, DI Figure 25 SK, DI Pin Figure 26 TEST Pin TEST 22 Seiko Instruments Inc. Rev.7.0_00 Rev.7.0_00 2. 2 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Output pin VCC DO Figure 27 3. DO Pin Input pin noise elimination time The S-93L46A/56A/66A include a built-in low-pass filter to eliminate noise at the SK, DI, and CS pins. This means that if the supply voltage is 5.0 V (at room temperature), noise with a pulse width of 20 ns or less can be eliminated. Note, therefore, the noise with a pulse width of more than 20 ns will be recognized as a pulse if the voltage exceeds VIH / VIL. Precautions * Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. * SII claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. Precautions for WLP package * The side of device silicon substrate is exposed to the marking side of device package. Since this portion has lower * strength against the mechanical stress than the standard plastic package, chip, crack, etc should be careful of the handing of a package enough. Moreover, the exposed side of silicon has electrical potential of device substrate, and needs to be kept out of contact with the external potential. In this package, the overcoat of the resin of translucence is carried out on the side of device area. Keep it mind that it may affect the characteristic of a device when exposed a device in the bottom of a high light source. Seiko Instruments Inc. 23 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Characteristics (Typical Data) 1. DC Characteristics 1. 1 Current consumption (READ) ICC1 vs. ambient temperature Ta 1. 2 Current consumption (READ) ICC1 vs. ambient temperature Ta VCC = 3.3 V fSK = 500 kHz DATA = 0101 VCC = 5.5 V fSK = 2 MHz DATA = 0101 0.4 0.4 ICC1 (mA) ICC1 (mA) 0.2 0.2 0 -40 0 85 0 -40 Ta (C) 1. 3 Current consumption (READ) ICC1 vs. ambient temperature Ta 1. 4 85 Current consumption (READ) ICC1 vs. power supply voltage VCC VCC = 1.8 V fSK = 10 kHz DATA = 0101 Ta = 25C fSK = 1 MHz, 500 kHz DATA = 0101 0.4 0.4 ICC1 (mA) ICC1 (mA) 0.2 0 0 Ta (C) 1 MHz 0.2 500 kHz -40 0 85 0 2 Ta (C) 3 4 5 6 7 VCC (V) 1. 5 Current consumption (READ) ICC1 vs. power supply voltage VCC Current consumption (READ) ICC1 vs. Clock frequency fSK VCC = 5.0 V Ta = 25C Ta = 25C fSK = 100 kHz, 10 kHz DATA = 0101 0.4 0.4 ICC1 (mA) 1. 6 ICC1 (mA) 100 kHz 0.2 0.2 0 10 kHz 0 2 3 4 5 6 10 k 7 1 M 2M 10M fSK (Hz) VCC (V) 24 100 k Seiko Instruments Inc. LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 1. 7 Current consumption (WRITE) ICC2 vs. ambient temperature Ta 1. 8 Current consumption (WRITE) ICC2 vs. ambient temperature Ta VCC = 3.3 V VCC = 5.5 V 1.0 1.0 0.5 ICC2 (mA) 0.5 ICC2 (mA) 0 -40 0 0 85 -40 0 85 Ta (C) Ta (C) 1. 9 Current consumption (WRITE) ICC2 vs. ambient temperature Ta 1. 10 Current consumption (WRITE) ICC2 vs. power supply voltage VCC VCC = 2.7 V Ta = 25C 1.0 1.0 ICC2 (mA) ICC2 (mA) 0.5 0 0.5 -40 0 0 85 Ta (C) 1. 11 1. 12 ISB (A) 5 6 7 Current consumption in standby mode ISB vs. power supply voltage VCC 1.0 0.5 0.5 0 4 Ta = 25C CS = GND VCC = 5.5 V CS = GND ISB (A) 3 VCC (V) Current consumption in standby mode ISB vs. ambient temperature Ta 1.0 2 -40 0 0 85 Ta (C) Seiko Instruments Inc. 2 3 4 5 6 VCC (V) 7 25 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 1. 13 Input leakage current ILI vs. ambient temperature Ta 1. 14 Rev.7.0_00 Input leakage current ILI vs. ambient temperature Ta VCC = 5.5 V CS, SK, DI, TEST = 0 V VCC = 5.5 V CS, SK, DI, TEST = 5.5 V 1.0 1.0 ILI (A) ILI (A) 0.5 0.5 0 0 -40 0 -40 0 85 85 Ta (C) Ta (C) 1. 15 Output leakage current ILO vs. ambient temperature Ta 1. 16 Output leakage current ILO vs. ambient temperature Ta VCC = 5.5 V DO = 5.5 V VCC = 5.5 V DO = 0 V 1.0 1.0 ILO (A) ILO (A) 0.5 0 0.5 -40 0 0 85 -40 0 Ta (C) 1. 17 4.6 VOH (V) Ta (C) High-level output voltage VOH vs. ambient temperature Ta 1. 18 VCC = 4.5 V IOH = -400 A 2.7 VOH (V) 4.4 High-level output voltage VOH vs. ambient temperature Ta VCC = 2.7 V IOH = -100 A 2.6 2.5 4.2 -40 0 -40 85 0 Ta (C) Ta (C) 26 85 Seiko Instruments Inc. 85 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 1. 19 High-level output voltage VOH vs. ambient temperature Ta High-level output voltage VOH vs. ambient temperature Ta VCC = 2.5 V IOH = -100 A 2.5 VOH (V) 1. 20 1.9 2.4 VOH (V) VCC = 1.8 V IOH = -10 A 1.8 2.3 1.7 -40 0 -40 85 Ta (C) 1. 21 VOL (V) 1. 22 Low-level output voltage VOL vs. ambient temperature Ta VCC = 4.5 V IOL = 2.1 mA 0.03 0.2 VOL 0.02 (V) 0.1 0.01 -40 0 85 VCC = 1.8 V IOL = 100 A -40 Ta (C) 1. 23 85 Ta (C) Low-level output voltage VOL vs. ambient temperature Ta 0.3 0 0 85 Ta (C) High-level output current IOH vs. ambient temperature Ta 1. 24 High-level output current IOH vs. ambient temperature Ta VCC = 2.7 V VOH = 2.4 V VCC = 4.5 V VOH = 2.4 V -2 -20.0 IOH (mA) IOH (mA) -1 -10.0 0 -40 0 85 0 Ta (C) Seiko Instruments Inc. -40 0 85 Ta (C) 27 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 1. 25 High-level output current IOH vs. ambient temperature Ta 1. 26 Rev.7.0_00 High-level output current IOH vs. ambient temperature Ta VCC = 2.5 V VOH = 2.2 V VCC = 1.8 V VOH = 1.6 V -2 -1.0 IOH (mA) IOH (mA) -1 0 -0.5 0 -40 0 -40 85 0 Ta (C) 1. 27 Ta (C) Low-level output current IOL vs. ambient temperature Ta 1. 28 Low-level output current IOL vs. ambient temperature Ta VCC = 1.8 V VOL = 0.1 V VCC = 4.5 V VOL = 0.4 V 1.0 20 IOL (mA) IOL (mA) 0.5 10 0 1. 29 -40 0 0 85 Ta (C) Input inverted voltage VINV vs. power supply voltage VCC 1. 30 Ta = 25C CS, SK, DI 3.0 0 85 Ta (C) Input inverted voltage VINV vs. ambient temperature Ta 3.0 VINV (V) 2.0 1.5 0 -40 VCC = 5.0 V CS, SK, DI VINV (V) 1 2 3 4 5 6 7 0 VCC (V) 28 85 Seiko Instruments Inc. -40 0 Ta (C) 85 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Low supply voltage detection voltage -VDET vs. ambient temperature Ta 1. 31 Low supply voltage release voltage +VDET vs. ambient temperature Ta 1. 32 2.0 2.0 +VDET (V) -VDET (V) 1.0 1.0 0 -40 0 0 85 -40 0 Ta (C) Ta (C) 2. 85 AC Characteristics 2. 1 Maximum operating frequency fMAX. vs. power supply voltage VCC 2. 2 Write time tPR vs. power supply voltage VCC Ta = 25C fMAX. (Hz) Ta = 25C 2M 1M 4 tPR (ms) 100k 2 10k 2 1 3 4 5 1 2 VCC (V) 2. 3 3 4 5 6 7 VCC (V) Write time tPR vs. ambient temperature Ta 2. 4 Write time tPR vs. ambient temperature Ta VCC = 5.0 V VCC = 3.0 V 6 tPR (ms) tPR (ms) 4 6 4 2 2 -40 0 85 -40 Ta (C) 0 85 Ta (C) Seiko Instruments Inc. 29 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 2. 5 Write time tPR vs. ambient temperature Ta 2. 6 Data output delay time tPD vs. ambient temperature Ta VCC = 2.7 V VCC = 4.5 V 6 0.3 tPR (ms) tPD (s) 4 0.2 2 0.1 -40 0 85 -40 Ta (C) 2. 7 Data output delay time tPD vs. ambient temperature Ta 2. 8 0 Ta (C) 85 Data output delay time tPD vs. ambient temperature Ta VCC = 2.7 V VCC = 1.8 V 0.6 1.5 tPD (s) tPD (s) 0.4 1.0 0.2 0.5 -40 0 85 -40 Ta (C) 30 Rev.7.0_00 0 Ta (C) Seiko Instruments Inc. 85 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A Rev.7.0_00 Product Name Structure 1. Product name 1. 1 8-Pin SOP (JEDEC), 8-Pin TSSOP, SNT-8A S-93LxxA x 0I - xxxx x Environmental code U: Lead-free (Sn 100%), halogen-free G: Lead-free (for details, please contact our sales office) Package name (abbreviation) and IC packing specifications J8T1: 8-Pin SOP (JEDEC), Tape T8T1: 8-Pin TSSOP, Tape I8T1: SNT-8A, Tape Fixed Pin configurations D: 8-Pin SOP (JEDEC) 8-Pin TSSOP SNT-8A R: 8-Pin SOP (JEDEC) (Rotated) Product name S-93L46A: 1 K-bit S-93L56A: 2 K-bit S-93L66A: 4 K-bit 1. 2 TMSOP-8 S-93LxxA D0I - K8T3 U Environmental code U: Lead-free (Sn 100%), halogen-free Package name (abbreviation) and IC packing specifications K8T3: TMSOP-8, Tape Fixed Product name S-93L46A: 1 K-bit S-93L56A: 2 K-bit S-93L66A: 4 K-bit 1. 3 WLP-7D S-93L66A D0I - H7T4 S Environmental code S: Lead-free, halogen-free Package name (abbreviation) and IC packing specifications H7T4: WLP-7D, Tape Fixed Product name S-93L66A: 4 K-bit Seiko Instruments Inc. 31 LOW VOLTAGE OPERATION 3-WIRE SERIAL E2PROM S-93L46A/56A/66A 2. Packages Package name 8-Pin SOP (JEDEC) 8-Pin TSSOP TMSOP-8 SNT-8A WLP-7D 32 Rev.7.0_00 Environmental code = G Environmental code = U Environmental code = G Environmental code = U Drawing code Package FJ008-A-P-SD FJ008-A-P-SD FT008-A-P-SD FT008-A-P-SD FM008-A-P-SD PH008-A-P-SD HD007-C-P-SD Tape Reel FJ008-D-C-SD FJ008-D-C-SD FT008-E-C-SD FT008-E-C-SD FM008-A-C-SD PH008-A-C-SD HD007-C-C-SD FJ008-D-R-SD FJ008-D-R-S1 FT008-E-R-SD FT008-E-R-S1 FM008-A-R-SD PH008-A-R-SD HD007-A-R-SD Seiko Instruments Inc. Land PH008-A-L-SD 5.020.2 8 5 1 4 1.27 0.200.05 0.40.05 No. FJ008-A-P-SD-2.1 TITLE No. SOP8J-D-PKG Dimensions FJ008-A-P-SD-2.1 SCALE UNIT mm Seiko Instruments Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 o1.550.05 0.30.05 o2.00.05 8.00.1 2.10.1 5max. 6.70.1 1 8 4 5 Feed direction No. FJ008-D-C-SD-1.1 TITLE SOP8J-D-Carrier Tape No. FJ008-D-C-SD-1.1 SCALE UNIT mm Seiko Instruments Inc. 60 20.5 13.50.5 Enlarged drawing in the central part o210.8 20.5 o130.2 No. FJ008-D-R-SD-1.1 TITLE SOP8J-D-Reel No. FJ008-D-R-SD-1.1 SCALE UNIT QTY. mm Seiko Instruments Inc. 2,000 60 20.5 13.50.5 Enlarged drawing in the central part o210.8 20.5 o130.2 No. FJ008-D-R-S1-1.0 TITLE SOP8J-D-Reel No. FJ008-D-R-S1-1.0 SCALE UNIT QTY. mm Seiko Instruments Inc. 4,000 +0.3 3.00 -0.2 8 5 1 4 0.170.05 0.20.1 0.65 No. FT008-A-P-SD-1.1 TITLE TSSOP8-E-PKG Dimensions FT008-A-P-SD-1.1 No. SCALE UNIT mm Seiko Instruments Inc. 4.00.1 2.00.05 o1.550.05 0.30.05 +0.1 8.00.1 o1.55 -0.05 (4.4) +0.4 6.6 -0.2 1 8 4 5 Feed direction No. FT008-E-C-SD-1.0 TITLE TSSOP8-E-Carrier Tape FT008-E-C-SD-1.0 No. SCALE UNIT mm Seiko Instruments Inc. 13.41.0 17.51.0 Enlarged drawing in the central part o210.8 20.5 o130.5 No. FT008-E-R-SD-1.0 TITLE TSSOP8-E-Reel No. FT008-E-R-SD-1.0 SCALE QTY. UNIT mm Seiko Instruments Inc. 3,000 13.41.0 17.51.0 Enlarged drawing in the central part o210.8 20.5 o130.5 No. FT008-E-R-S1-1.0 TITLE TSSOP8-E-Reel FT008-E-R-S1-1.0 No. SCALE UNIT QTY. mm Seiko Instruments Inc. 4,000 2.900.2 8 5 1 4 0.130.1 0.20.1 0.650.1 No. FM008-A-P-SD-1.0 TITLE TMSOP8-A-PKG Dimensions No. FM008-A-P-SD-1.0 SCALE UNIT mm Seiko Instruments Inc. 2.000.05 4.000.1 4.000.1 1.000.1 +0.1 1.55 -0 1.050.05 0.300.05 3.250.05 4 1 5 8 Feed direction No. FM008-A-C-SD-1.0 TITLE TMSOP8-A-Carrier Tape FM008-A-C-SD-1.0 No. SCALE UNIT mm Seiko Instruments Inc. 16.5max. 13.00.3 Enlarged drawing in the central part 130.2 (60) (60) No. FM008-A-R-SD-1.0 TMSOP8-A-Reel TITLE FM008-A-R-SD-1.0 No. SCALE UNIT QTY. 4,000 mm Seiko Instruments Inc. 1.970.03 8 7 6 5 3 4 +0.05 1 0.5 2 0.08 -0.02 0.480.02 0.20.05 No. PH008-A-P-SD-2.0 TITLE SNT-8A-A-PKG Dimensions PH008-A-P-SD-2.0 No. SCALE UNIT mm Seiko Instruments Inc. +0.1 o1.5 -0 5 2.250.05 4.00.1 2.00.05 o0.50.1 0.250.05 0.650.05 4.00.1 4 321 5 6 78 Feed direction No. PH008-A-C-SD-1.0 TITLE SNT-8A-A-Carrier Tape PH008-A-C-SD-1.0 No. SCALE UNIT mm Seiko Instruments Inc. 12.5max. 9.00.3 Enlarged drawing in the central part o130.2 (60) (60) No. PH008-A-R-SD-1.0 TITLE SNT-8A-A-Reel No. PH008-A-R-SD-1.0 SCALE UNIT QTY. mm Seiko Instruments Inc. 5,000 0.52 2.01 0.52 0.3 0.2 0.3 0.2 0.3 0.2 0.3 Caution Making the wire pattern under the package is possible. However, note that the package may be upraised due to the thickness made by the silk screen printing and of a solder resist on the pattern because this package does not have the standoff. No. PH008-A-L-SD-3.0 TITLE SNT-8A-A-Land Recommendation PH008-A-L-SD-3.0 No. SCALE UNIT mm Seiko Instruments Inc. 1.500.03 1.280.03 0.33max. S 0.04 S o0.250.02 0.080.02 B 0.5 0.5 7-(o0.25) 4 A 0.43 0.43 3 5 o0.05 M S A B 2 6 1 0.5 7 Pin No. Pin name 1 CS 2 3 4 5 6 7 DI VCC TEST GND DO SK No. HD007-C-P-SD-2.0 TITLE WLP-7D-C-PKG Dimensions (S-93L66AD) No. HD007-C-P-SD-2.0 SCALE UNIT Seiko Instruments Inc. +0.1 2.00.05 o1.5 -0 o0.50.05 2.00.1 1.66 1.360.05 3 4.00.1 0.180.05 0.550.05 4.00.1 0.7 0.5 1 7 4 5 6 Feed direction No. HD007-C-C-SD-1.0 TITLE No. WLP-7D-C-C a r r i e r T a p e (S-93L66AD) HD007-C-C-SD-1.0 SCALE UNIT mm Seiko Instruments Inc. 12.5max. 9.00.3 Enlarged drawing in the central part o130.2 No. HD007-A-R-SD-1.1 TITLE No. WLP-7D-C-Reel (S-93L66AD) HD007-A-R-SD-1.1 SCALE UNIT QTY. 3,000 mm Seiko Instruments Inc. www.sii-ic.com * * * * * * * The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. The products described herein are not designed to be radiation-proof. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.