Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series SMDJ Series RoHS Pb e3 Description Uni-directional The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 3000 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only(Note 4) VF 3.5/5.0 V Operating Temperature Range TJ -65 to 150 C Storage Temperature Range TSTG -65 to 175 C Typical Thermal Resistance Junction to Lead RJL 15 C/W Typical Thermal Resistance Junction to Ambient RJA 75 C/W Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig. 2,4) (Note 1,2,5) Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle=4 per minute maximum. * 3000W PPPM capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * For surface mounted applications in order to optimize board space * Low profile package * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * EFT protection of data lines in accordance with IEC 61000-4-4 * Built-in strain relief * Glass passivated chip junction * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 2A when VBR min>12V * High temperature to reflow soldering guaranteed: 260C/40sec * VBR @ TJ= VBR@25C x (1+T x (TJ - 25))(T:Temperature Coefficient, typical value is 0.1%) * UL Recognized compound meeting flammability rating V-0 * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications TVS components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in telecom, computer, Industrial and consumer electronic applications. 4. VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 5. The PPPM of stacked-die parts is 4000W and please contact Littelfuse for stacked-die part details. Additional Infomarion Functional Diagram Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Electrical Characteristics (T =25C unless otherwise noted) A Marking Part Number (Uni) Part Number (Bi) SMDJ5.0A SMDJ5.0CA RDE DDE SMDJ6.0A SMDJ6.0CA RDG DDG SMDJ6.5A SMDJ6.5CA RDK SMDJ7.0A SMDJ7.0CA SMDJ7.5A UNI BI Reverse Stand off Voltage V Breakdown Voltage V Test Current IT (mA) Maximum Clamping Voltage VC @ Ipp(10/1000s) (V) Maximum Maximum Maximum Maximum Peak Clamping Peak Maximum Agency Reverse Pulse Voltage VC Pulse Temperature Approval Leakage IR Current @ Current coefficient @ VR Ipp(10/1000s) Ipp(8/20s) Ipp(8/20s) of VBR (%/C) (A) (A) (V) (A) MIN MAX 5.0 6.40 7.00 10 9.2 326.1 11.89 1630.5 800 0.041 X 6.0 6.67 7.37 10 10.3 291.3 13.31 1456.5 800 0.046 X DDK 6.5 7.22 7.98 10 11.2 267.9 14.47 1339.5 500 0.052 X PDM DDM 7.0 7.78 8.60 10 12.0 250.0 15.50 1250.0 200 0.058 X SMDJ7.5CA PDP DDP 7.5 8.33 9.21 1 12.9 232.6 16.67 1163.0 100 0.061 X SMDJ8.0A SMDJ8.0CA PDR DDR 8.0 8.89 9.83 1 13.6 220.6 17.57 1103.0 50 0.064 X SMDJ8.5A SMDJ8.5CA PDT DDT 8.5 9.44 10.40 1 14.4 208.3 18.60 1041.5 20 0.066 X SMDJ9.0A SMDJ9.0CA PDV DDV 9.0 10.00 11.10 1 15.4 194.8 19.90 974.0 10 0.069 X SMDJ10A SMDJ10CA PDX DDX 10.0 11.10 12.30 1 17.0 176.5 21.96 882.5 5 0.071 X SMDJ11A SMDJ11CA PDZ DDZ 11.0 12.20 13.50 1 18.2 164.8 23.51 824.0 2 0.074 X SMDJ12A SMDJ12CA PEE DEE 12.0 13.30 14.70 1 19.9 150.8 25.71 754.0 2 0.075 X SMDJ13A SMDJ13CA PEG DEG 13.0 14.40 15.90 1 21.5 139.5 27.78 697.5 2 0.076 X SMDJ14A SMDJ14CA PEK DEK 14.0 15.60 17.20 1 23.2 129.3 29.97 646.5 2 0.08 X SMDJ15A SMDJ15CA PEM DEM 15.0 16.70 18.50 1 24.4 123.0 31.52 615.0 2 0.083 X SMDJ16A SMDJ16CA PEP DEP 16.0 17.80 19.70 1 26.0 115.4 33.59 577.0 2 0.084 X SMDJ17A SMDJ17CA PER DER 17.0 18.90 20.90 1 27.6 108.7 35.66 543.5 2 0.085 X SMDJ18A SMDJ18CA PET DET 18.0 20.00 22.10 1 29.2 102.7 37.73 513.5 2 0.088 X SMDJ20A SMDJ20CA PEV DEV 20.0 22.20 24.50 1 32.4 92.6 41.86 463.0 2 0.091 X SMDJ22A SMDJ22CA PEX DEX 22.0 24.40 26.90 1 35.5 84.5 45.87 422.5 2 0.092 X SMDJ24A SMDJ24CA PEZ DEZ 24.0 26.70 29.50 1 38.9 77.1 50.26 385.5 2 0.092 X SMDJ26A SMDJ26CA PFE DFE 26.0 28.90 31.90 1 42.1 71.3 54.39 356.5 2 0.093 X SMDJ28A SMDJ28CA PFG DFG 28.0 31.10 34.40 1 45.4 66.1 58.66 330.5 2 0.094 X SMDJ30A SMDJ30CA PFK DFK 30.0 33.30 36.80 1 48.4 62.0 62.53 310.0 2 0.096 X SMDJ33A SMDJ33CA PFM DFM 33.0 36.70 40.60 1 53.3 56.3 68.86 281.5 2 0.097 X SMDJ36A SMDJ36CA PFP DFP 36.0 40.00 44.20 1 58.1 51.6 75.06 258.0 2 0.098 X SMDJ40A SMDJ40CA PFR DFR 40.0 44.40 49.10 1 64.5 46.5 83.33 232.5 2 0.099 X SMDJ43A SMDJ43CA PFT DFT 43.0 47.80 52.80 1 69.4 43.2 89.66 216.0 2 0.1 X SMDJ45A SMDJ45CA PFV DFV 45.0 50.00 55.30 1 72.7 41.3 93.93 206.5 2 0.101 X SMDJ48A SMDJ48CA PFX DFX 48.0 53.30 58.90 1 77.4 38.8 100.00 194.0 2 0.101 X SMDJ51A SMDJ51CA PFZ DFZ 51.0 56.70 62.70 1 82.4 36.4 106.46 182.0 2 0.101 X SMDJ54A SMDJ54CA RGE DGE 54.0 60.00 66.30 1 87.1 34.4 112.53 172.0 2 0.102 X SMDJ58A SMDJ58CA PGG DGG 58.0 64.40 71.20 1 93.6 32.1 120.93 160.5 2 0.103 X SMDJ60A SMDJ60CA PGK DGK 60.0 66.70 73.70 1 96.8 31.0 125.06 155.0 2 0.103 X SMDJ64A SMDJ64CA PGM DGM 64.0 71.10 78.60 1 103.0 29.1 133.07 145.5 2 0.104 X SMDJ70A SMDJ70CA PGP DGP 70.0 77.80 86.00 1 113.0 26.5 145.99 132.5 2 0.105 X SMDJ75A SMDJ75CA PGR DGR 75.0 83.30 92.10 1 121.0 24.8 156.33 124.0 2 0.106 X SMDJ78A SMDJ78CA PGT DGT 78.0 86.70 95.80 1 126.0 23.8 162.79 119.0 2 0.106 X SMDJ85A SMDJ85CA PGV DGV 85.0 94.40 104.00 1 137.0 21.9 177.00 109.5 2 0.106 X SMDJ90A SMDJ90CA PGX DGX 90.0 100.00 111.00 1 146.0 20.5 188.63 102.5 2 0.107 X SMDJ100A SMDJ100CA PGZ DGZ 100.0 111.00 123.00 1 162.0 18.5 209.30 92.5 2 0.107 X SMDJ110A SMDJ110CA PHE DHE 110.0 122.00 135.00 1 177.0 16.9 228.68 84.5 2 0.107 X SMDJ120A SMDJ120CA PHG DHG 120.0 133.00 147.00 1 193.0 15.5 249.35 77.5 2 0.108 X SMDJ130A SMDJ130CA PHK DHK 130.0 144.00 159.00 1 209.0 14.4 270.03 72.0 2 0.108 X SMDJ150A SMDJ150CA PHM DHM 150.0 167.00 185.00 1 243.0 12.3 313.95 61.5 2 0.108 X SMDJ160A SMDJ160CA PHP DHP 160.0 178.00 197.00 1 259.0 11.6 334.63 58.0 2 0.108 X SMDJ170A PHR DHR 170.0 189.00 209.00 1 275.0 10.9 355.30 54.5 2 0.108 X X SMDJ170CA SMDJ180A SMDJ180CA PHT DHT 180.0 200.00 221.00 1 292.0 10.3 377.26 51.5 2 0.108 SMDJ200A SMDJ200CA PHV DHV 200.0 224.00 247.00 1 324.0 9.3 418.60 46.5 3 0.11 X SMDJ220A SMDJ220CA PKE DKE 220.0 244.00 270.00 1 356.0 8.4 459.95 42.0 2 0.11 X SMDJ250A SMDJ250CA PKG DKG 250.0 279.00 309.00 1 405.0 7.5 523.26 37.5 2 0.11 X SMDJ300A SMDJ300CA PKI DKI 300.0 335.00 371.00 1 486.0 6.2 627.91 31.0 2 0.112 X SMDJ350A SMDJ350CA PKJ DKJ 350.0 391.00 432.00 1 567.0 5.3 732.56 26.5 2 0.112 X SMDJ400A SMDJ400CA PKL DKL 400.0 447.00 494.00 1 648.0 4.7 837.21 23.5 2 0.112 X SMDJ440A SMDJ440CA PKN DKN 440.0 492.00 543.00 1 713.0 4.3 921.19 21.5 2 0.112 X (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR V IR VF IT IT IR Vc VBR VR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS stacked-die, 4kW at 10/1000s, 25C 10 Current Through TVS Single die, 3kW at 10/1000s, 25C 1 TJ initial = Tamb 0.1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) 2 Uni-direconal V=VR Bi-direconal V=VR 10 100 td 1.0 0 3.0 4.0 10 1 0.1 0.01 0.001 1000 0.01 0.1 VBR - Reverse Breakdown Voltage(V) 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward 500 Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100 450 IF- Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) 2.0 100 1 10 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Transient Thermal Impedance (C/W) Cj(pF) Bi-direconal V=0V 1 ( ) 50 Figure 6 - Typical Transient Thermal Impedance Uni-direconal V=0V 100 Half Value IPPM IPPM 175 100000 10000 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 0 Figure 5 - Typical Junction Capacitance 1000 tr=10sec 400 350 300 250 200 150 100 Single die 10 Stack-die 1 0.1 50 0.01 0 1 10 Number of Cycles at 60 Hz (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18 100 0.00 1.00 2.00 3.00 4.00 5.00 6.00 VF-Peak Forward Voltage(V) 7.00 8.00 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TA) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.007 ounce, 0.21 grams Temperature Cycling JESD22-A104 Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes positive end (cathode) except for bidirectional versions. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-A111 Dimensions DO-214AB (SMC J-Bend) Cathode Band (for uni-directional products only) C A B H D J I E L K F G Dimensions Inches Min Millimeters Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 L 0.094 - 4.200 2.400 - Dimensions in Pads inches and (millimeters) Solder (all dimensions in mm) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Part Numbering System Part Marking System SMDJ XXX C A F Cathode Band 5% VBR VOLTAGE TOLERANCE BI-DIRECTIONAL (for uni-directional products only) Littelfuse Logo XXX VR VOLTAGE YMXXX SERIES Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Part number Component Package SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm tape/13" reel EIA STD RS-481 SMDJxxxXX-T7 DO-214AB 500 Tape & Reel - 16mm tape/7" reel EIA STD RS-481 Packaging Option Quantity Packaging Specification Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). *For Uni-directional Products only Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/27/18