SPBT3.0DP1 Bluetooth(R) Classic module Datasheet - production data Features Bluetooth radio Fully embedded Bluetooth(R) v3.0 with SPP and HID profiles Class 1 module Enhanced Data Rate (EDR) support Complete RF-ready module September 2017 Embedded support for MFi iAP2 profile 128-bit encryption security Integrated antenna ST Cortex-M4 microprocessor Up to 100 MHz 512 KB Flash 128 KB RAM Supports transmission speed with SPP up to 1500 Kbit/s 14 general-purpose I/Os User interface AT command Data Package (DP) Firmware upgrade over UART EU, FCC, IC and Bluetooth qualified Single voltage supply: 3.3 V typical Small form factor: 15.24 x 26.9 x 2.9 mm Operating temperature range: -40 C to 85 C DocID029412 Rev 2 This is information on a product in full production. 1/35 www.st.com Contents SPBT3.0DP1 Contents 1 Description....................................................................................... 6 2 RoHS compliance ............................................................................ 7 3 Applications ..................................................................................... 8 4 Software architecture ...................................................................... 9 4.1 BT stack layers.................................................................................. 9 4.2 Supported profile ............................................................................. 10 4.3 AT command set: Data Package..................................................... 10 5 Module block diagram ................................................................... 11 6 Hardware specifications ............................................................... 12 7 6.1 Recommended operating conditions ............................................... 12 6.2 Radio features ................................................................................. 12 6.3 Absolute maximum ratings .............................................................. 12 6.4 Current consumption ....................................................................... 12 6.5 I/O operating characteristics............................................................ 13 6.6 Pin assignment................................................................................ 14 Package information ..................................................................... 16 7.1 8 9 10 Hardware design ........................................................................... 19 8.1 Reflow soldering.............................................................................. 19 8.2 UART interface................................................................................ 20 8.3 GPIO interface ................................................................................ 21 8.4 Reset circuit .................................................................................... 22 8.4.1 Simple external reset circuit ............................................................. 22 8.4.2 Host controlled reset circuit .............................................................. 22 8.5 MFi co-processor interface .............................................................. 23 8.6 PCB layout guidelines ..................................................................... 24 Firmware upgrade ......................................................................... 26 9.1 Enter bootloader mode .................................................................... 26 9.2 Transfer the new firmware .............................................................. 26 9.3 Exit bootloader mode ...................................................................... 26 Regulatory compliance ................................................................. 27 10.1 2/35 RF module package information ..................................................... 17 FCC certification.............................................................................. 27 DocID029412 Rev 2 SPBT3.0DP1 10.2 Contents 10.1.1 FCC labeling instructions.................................................................. 27 10.1.2 Product manual instructions for FCC compliance ............................ 28 IC certification ................................................................................. 28 10.2.1 IC labeling instructions ..................................................................... 29 10.2.2 Product manual instructions for IC compliance ................................ 29 10.3 Bluetooth certification ...................................................................... 30 10.4 CE certification ................................................................................ 30 11 Traceability .................................................................................... 32 12 Ordering information..................................................................... 33 13 Revision history ............................................................................ 34 DocID029412 Rev 2 3/35 List of tables SPBT3.0DP1 List of tables Table 1: Recommended operating conditions .......................................................................................... 12 Table 2: Radio features............................................................................................................................. 12 Table 3: Absolute maximum ratings ......................................................................................................... 12 Table 4: Power consumption .................................................................................................................... 13 Table 5: I/O operating characteristics ....................................................................................................... 13 Table 6: Pin assignment ........................................................................................................................... 14 Table 7: Soldering ..................................................................................................................................... 19 Table 8: Traceability information ............................................................................................................... 32 Table 9: Ordering information ................................................................................................................... 33 Table 10: Document revision history ........................................................................................................ 34 4/35 DocID029412 Rev 2 SPBT3.0DP1 List of figures List of figures Figure 1: Software architecture overview ................................................................................................... 9 Figure 2: SPBT3.0DP1 block diagram ...................................................................................................... 11 Figure 3: Pin assignment .......................................................................................................................... 14 Figure 4: RF module package outline (dimensions in mm) ...................................................................... 17 Figure 5: Recommended land (top view) pattern (dimensions in mm) ..................................................... 18 Figure 6: Soldering profile ......................................................................................................................... 20 Figure 7: Connection to host device ......................................................................................................... 20 Figure 8: Typical RS232 circuit ................................................................................................................. 21 Figure 9: Simple external reset circuit ...................................................................................................... 22 Figure 10: Host controlled reset circuit ..................................................................................................... 22 Figure 11: SPBT3.0DP2 to MFi coprocessor interconnections ................................................................ 24 Figure 12: Power supply capacitors .......................................................................................................... 25 Figure 13: CE marking .............................................................................................................................. 31 DocID029412 Rev 2 5/35 Description 1 SPBT3.0DP1 Description The SPBT3.0DP1 is an easy-to-use Bluetooth module that is compliant with Bluetooth v3.0. The module has among the smallest form factors available in a complete Class 1 RF platform. The SPBT3.0DP1 enables electronic devices with wireless connectivity, requiring no RF experience or expertise to integrate into the final product. As a certified solution, the SPBT3.0DP1 module optimizes time-to-market for end-applications. The module is designed for maximum performance in a minimal space including high speed UART and 14 general purpose I/O lines, and up to 1500 kbps transmission speed with SPP service active and 1000 kbps with iAP2 service active. Its optimized design allows the integration of a complete working Bluetooth modem, including antenna, in the smallest possible size. Deep Sleep mode reduces power consumption when a Bluetooth connection is not established. The SPBT3.0DP1 is a surface-mount PCB module that provides fully embedded, ready-touse Bluetooth wireless technology. The reprogrammable Flash memory contains embedded firmware for serial cable replacement using the Bluetooth SPP profile. Embedded Bluetooth Data Package (DP) firmware provides a user-friendly interface, offering simple control for cable replacement and enabling communication with most Bluetooth-enabled devices that support the SPP profile. The SPBT3.0DP1 supports the iAP2 profile, allowing communication with the newest Apple(R) iOS Bluetooth-enabled devices. An Apple authentication IC is required to exchange data with an Apple device or access an Apple device application. The DP FW includes a Bluetooth iAP2 profile capable of recognizing the Apple authentication chip. Customers using the Apple authentication IC must register as developers to become an Apple certified MFi member. License fees may apply. For additional information, please visit the Apple developer website. Certified MFi developers developing electronic accessories that connect to the iPod (R), iPhone(R) and iPad(R), gain access to technical documentation, hardware components, technical support and certification logos. Customized firmware for peripheral device interaction, power optimization, security, and other proprietary features may be supported and can be ordered pre-loaded and configured. 6/35 DocID029412 Rev 2 SPBT3.0DP1 2 RoHS compliance RoHS compliance ST Bluetooth modules comply with the ECOPACK2 level of RoHS compliance. DocID029412 Rev 2 7/35 Applications 3 SPBT3.0DP1 Applications The SPBT3.0DP1 is suitable for a wide range of applications, such as: 8/35 Serial cable replacement M2M industrial control Service diagnostics Data acquisition equipment Machine control Sensor monitoring Security systems Mobile health DocID029412 Rev 2 SPBT3.0DP1 4 Software architecture Software architecture Figure 1: Software architecture overview 4.1 BT stack layers Bluetooth v3.0 Device power modes: active, deep sleep Connection modes: active, sniff Wake on Bluetooth feature optimizes power consumption of host CPU DocID029412 Rev 2 9/35 Software architecture 4.2 Supported profile 4.3 SPBT3.0DP1 Authentication and encryption Encryption key length from 8 bits to 128 bits Secure simple pairing support Persistent Flash memory for BD address and user parameter storage All ACL (asynchronous connection-less) packet types Master/slave switch supported during connection and post connection Dedicated inquiry access code for improved inquiry scan performance Dynamic packet selection channel quality-driven data rate to optimize link performance Dynamic power control Bluetooth radio natively supports 802.11b co-existence AFH RFCOMM, SDP, and L2CAP protocols supported Serial port profile (SPP) Human interface device (HID) iPhone accessory profile 2 (iAP2) Device identification profile (DID) AT command set: Data Package The complete command list is available in user manual UM2077 SPBT3.0DPx data package, which you can download from www.st.com. 10/35 DocID029412 Rev 2 SPBT3.0DP1 5 Module block diagram Module block diagram Figure 2: SPBT3.0DP1 block diagram DocID029412 Rev 2 11/35 Hardware specifications 6 SPBT3.0DP1 Hardware specifications General conditions (VIN = 3.3 V and 25 C). 6.1 Recommended operating conditions Table 1: Recommended operating conditions 6.2 Rating Min. Typical Max. Unit Operating temperature range - 40 - +8 5 C Supply voltage VIN 2.1 3.3 3.6 V Signal pin voltage - 1.8 - V Radio features Table 2: Radio features Feature Min. Typical Max. Bluetooth version - 3.0 - Bluetooth class - 1 - Radiated transmit power - - 10.77 dBm Receiver sensitivity - -88 - dBm 2402 - 2480 MHz RF frequency 6.3 Unit Absolute maximum ratings Table 3: Absolute maximum ratings Rating Min. Typical Max. Unit Storage temperature range -40 - +85 C Supply voltage, VIN -0.3 - +5.5 V I/O pin voltage, VIO -0.3 +1.8 +2.1(1) V Notes: (1) 6.4 for pins not 5 V tolerant Current consumption Test conditions: 12/35 Configuration variable: default Temperature: 25 C DocID029412 Rev 2 SPBT3.0DP1 Hardware specifications Table 4: Power consumption Modes (typical power consumption) Typical Unit 1.5 mA No connection, Page/Inquiry Scan, Active Mode 9 mA Connection, no data traffic, Active Mode 12 mA Connection, no data traffic, Sniff Mode 9.5 mA Connection, 450 Kbps tx rx data , Active mode 26(1) mA No connection, Page/Inquiry Scan, Deep Sleep Mode Notes: (1)Peak 6.5 current during transmission: 80 mA. I/O operating characteristics Table 5: I/O operating characteristics Symbol Parameter Min. Max. Unit Conditions VIL Low-level input voltage - 0.5 V VIN, 3.3 V VIH High-level input voltage 1.3 - V VIN, 3.3 V VOL Low-level output voltage - 0.5 V VIN, 3.3 V VOH High-level output voltage 1.4 - V VIN, 3.3 V IOL Low-level output current - 4(1) mA VOL = 0.4 V IOH High-level output current - 4 (1) mA VOH = 1.8 V RPU Pull-up resistor 30 50 k Resistor turned on(2) RPD Pull-down resistor 30 50 k Resistor turned on (2) Notes: (1)GPIO14 max sunk or sourced current is limited to 3mA. The speed should not exceed 2 MHz with a maximum load of 30 pF. This I/O must not be used as a current source (e.g. to drive an LED). (2)Normally not used. Firmware dependent. DocID029412 Rev 2 13/35 Hardware specifications 6.6 SPBT3.0DP1 Pin assignment Figure 3: Pin assignment Table 6: Pin assignment Pin Name Description I/O Notes 1 GPIO_3 General purpose I/O I/O 5 V tolerant 2 BOOT_0 Boot pin I Internal 10K pull-down 3 RESET Reset input (active low for 5 ms) I 4 GPIO_8 General purpose I/O I/O 5 V tolerant 5 GPIO_10 General purpose I/O I/O 5 V tolerant 6 TXD Transmit Data O 5 V tolerant 7 GPIO_9 General purpose I/O I/O 5 V tolerant 8 RXD Receive Data I 5 V tolerant 9 CTS Clear to send (active low) I 5 V tolerant 10 RTS Request to send (active low) O 5 V tolerant 11 GPIO_11 I2C_SCL line for MFi chip or General purpose I/O I/O 5 V tolerant 12 GPIO_12 I2C_SDA line for MFi chip or General purpose I/O I/O 5 V tolerant 13 GPIO_7 General purpose I/O I/O 5 V tolerant 14 GPIO_14 General purpose I/O I/O 5 V tolerant 15 GPIO_13 General purpose I/O I/O 5 V tolerant 16 LPO_OUT Low power 32KHz oscillator output O GPIO indicating BT Connection Status 17 14/35 GPIO_1 1: BT connection is active 0: BT connection is not active DocID029412 Rev 2 O 5 V tolerant SPBT3.0DP1 Pin Hardware specifications Name Description I/O Notes O 5 V tolerant GPIO indicating Module Power Status 18 GPIO_4 19 GPIO_2 General purpose I/O I/O 20 GPIO_5 General purpose I/O I/O 21 1.8V_OUT +1.8V out (max 10mA) 22 GPIO_6 General purpose I/O 23 GND Reference ground 24 VIN Main power supply input 1: active mode 0: Deep Sleep Mode I/O 5 V tolerant Some GPIOs can be configured with alternate functions. For details refer to the AT Command Data Package user manual. DocID029412 Rev 2 15/35 Package information 7 SPBT3.0DP1 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK (R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 16/35 DocID029412 Rev 2 SPBT3.0DP1 7.1 Package information RF module package information Figure 4: RF module package outline (dimensions in mm) DocID029412 Rev 2 17/35 Package information SPBT3.0DP1 Figure 5: Recommended land (top view) pattern (dimensions in mm) 18/35 DocID029412 Rev 2 SPBT3.0DP1 8 Hardware design Hardware design The SPBT3.0DP1 module with Data Package embedded firmware supports UART, IC and GPIO hardware interfaces. Note: 8.1 All unused pins (including the additional 6 pads on bottom side) should be left floating; do not ground. All GND pins must be well grounded. The area around the module should be free of any ground planes, power planes, trace routings, or metal for 6 mm from the module antenna position, in all directions. Traces should not be routed under the module. Reflow soldering The SPBT3.0DP1 is a high temperature-strength surface-mount Bluetooth module supplied on a PCB with the following characteristics: 24-pin, 6-layer . The recommended final assembly reflow profiles are indicated below. The soldering phase must be executed with care. To prevent undesired melting, particular attention must be paid to the setup of the peak temperature. The following soldering indications are based on temperature profile recommendations. Table 7: Soldering Profile feature PB-free assembly Average ramp-up rate (TSMAX to TP) 3 C/sec max Preheat: - Temperature min. (TS min.) - Temperature max. (TS max.) - Time (ts min. to ts max.)(ts) 150 C 200 C 60-100 sec Time maintained above: - Temperature TL - Temperature TL 217 C 60-70 sec Peak temperature (TP) 240 + 0 C Time within 5 C of actual peak temperature (TP) 10-20 sec Ramp-down rate 6 C/sec Time from 25 C to peak temperature 8 minutes max. DocID029412 Rev 2 19/35 Hardware design SPBT3.0DP1 Figure 6: Soldering profile 8.2 UART interface The UART is compatible with the 16550 industry standard. Four signals are provided with the UART interface. The TXD and RXD pins are used for data, while the CTS and RTS pins are used for flow control. Figure 7: Connection to host device 20/35 DocID029412 Rev 2 SPBT3.0DP1 Hardware design Figure 8: Typical RS232 circuit 8.3 GPIO interface Module GPIO configuration depends on the Data Package embedded firmware. By default the GPIO1, GPIO4, GPIO11 and GPIO12 have specific functions. The remaining GPIOs are available to the HOST processor that can configure them as GPIO or as alternate function ( GPIO_HostModeSel, GPIO_HostModeInd, GPIO_HostWakeUp, GPIO_FactoryReset .) GPIO1: Bluetooth Connection Status 0: BT connection not present 1: BT connection is present GPIO4: Module Power Status: 1: module is in Active Mode Blinking: module is in Deep Sleep Mode GPIO11: I2C SCL pin to be connected to MFi co-processor. External pull-up resistor is needed. It can be used as GPIO if MFi chip is not used. GPIO12: I2C SDA pin to be connected to MFi co-processor. External pull-up resistor is needed. It can be used as GPIO if MFi chip is not used. Pins used as generic GPIO can be handled by the HOST processor using the following commands: AT+AB GPIOConfig [GPIO pin] [I/O] AT+AB GPIORead [GPIO pin] AT+AB GPIOWrite [GPIO pin] [1/0] For more details about GPIOs alternate functions refer to the AT Command Data Package user manual. All GPIOs are capable of sinking and sourcing 4 mA of I/O current. (except GPIO14) (see note in Table 5: "I/O operating characteristics"). DocID029412 Rev 2 21/35 Hardware design 8.4 SPBT3.0DP1 Reset circuit Two types of system reset circuits are detailed below. The maximum voltage that can be supplied to the RESET pin is 3.6V, but it is suggested to use 1.8V VDD voltage, as there is an internal pull-up resistor to VDD. As shown in Figure 9: "Simple external reset circuit" and Figure 10: "Host controlled reset circuit" the RESET is active low, in the absence of a reset circuit the pin is internally pulled up and therefore inactive. 8.4.1 Simple external reset circuit The figure below shows a simple push-button reset circuit. Figure 9: Simple external reset circuit Note: RPU ranges from 30 k to 50 k internally provided. 8.4.2 Host controlled reset circuit The figure below shows a typical host controlled reset circuit. Figure 10: Host controlled reset circuit 22/35 DocID029412 Rev 2 SPBT3.0DP1 Note: 8.5 Hardware design RPU ranges from 30 k to 50 k internally. The host reset resistor should be from 1 k to 10 k MFi co-processor interface A specific MFi co-processor is needed to enable iAP2 profile for connection with Apple devices. The MFi co-processor component details are available for licensed MFi developers from the MFi program. The MFi co-processor can be connected to the module through the I2C pins. External pullup resistors are needed on both lines. The Data Package firmware handles the communication with the MFi co-processor. DocID029412 Rev 2 23/35 4 3 2 1 NC SCL RST VCC NC SCL RST APP LE MFI COPROCESS OR NC NC SDA GND U2 VCC APP LE MFI COPROCESS OR NC NC SDA GND Circuit with 3.3V coprocessor power supply 4 3 2 1 5 6 7 8 5 6 7 8 TBD TBD 6 SPB T_SCL 7 5 4 3 2 1 SPB T_SDA R4 2.2 kOhm GND GPIO06 GPIO05 GPIO04 GPIO03 GPIO02 GPIO01 ANTENNA SPBT3.0DP2 C4 100n R8 10 kOhm TBD R7 10 kOhm TBD R5 2.2 kOhm 6 SPB T_SCL 7 5 4 3 2 1 SPB T_SDA R6 2.2 kOhm 3.3V GND GPIO06 GPIO05 GPIO04 GPIO03 GPIO02 GPIO01 Note: R7 and R8 are used to select the I2CBus address: with only R7 mounted--> RST signal is at high logic level and are selected the 0x22 Write Address and 0x23 Read Address with only R8 mounted--> RST signal is at low logic level and are selected the 0x20 Write Address and 0x21 Read Address R2 10 kOhm R1 10 kOhm R3 2.2 kOhm 18 SPBT3.0DP2 ANTENNA LDOUT 17 GPIO07 U1 C1 100n LDOUT=1.8V 18 LDOUT 17 GPIO07 16 GPIO08 16 Circuit with 1.8V coprocessor power supply LPO 15 DocID029412 Rev 2 LPO 24/35 GPIO08 8.6 15 Note: R1 and R2 are used to select the I2CBus address: with only R1 mounted--> RST signal is at high logic level and are selected the 0x22 Write Address and 0x23 Read Address with only R2 mounted--> RST signal is at low logic level and are selected the 0x20 Write Address and 0x21 Read Address TXD BT2 VIN BOO T RESE T CTS RTS RXD TXD BT1 VIN BOO T RESE T CTS RTS RXD 8 9 10 11 12 13 14 8 9 10 11 12 13 14 3.3V 3.3V C2 C3 100n 100n Hardware design Figure 11: SPBT3.0DP2 to MFi coprocessor interconnections SPBT3.0DP1 PCB layout guidelines The SPBT3.0DP1 module require proper placement on PCB to ensure optimal performance. The antenna on the PCB has an omnidirectional radiation pattern. To maximize antenna efficiency, an adequate grounding plane must be provided under the module, respecting the distance for the antenna clearance. The position of the module on the host board and overall design of the product enclosure contributes to the antenna performance. Poor design can limit the antenna radiation SPBT3.0DP1 Hardware design patterns and can result in reflection, diffraction, and/or scattering of the transmitted signal thus limiting the useful operating range. Basic guidelines: Never place the ground plane or route copper traces directly underneath the antenna portion of the module Keep a 6 mm clear zone surrounding the antenna (no ground planes, no traces) Never place the antenna close to metallic objects Keep wiring, components and objects away from antenna Do not place the antenna in a metallic or metalized plastic enclosure Enclosure walls should be 20 mm or more away from the antenna in all directions If possible, mount antenna overhanging the edge of the host board Place power supply capacitors very close to VIN pin, with minimum values shown in following figure Figure 12: Power supply capacitors DocID029412 Rev 2 25/35 Firmware upgrade 9 SPBT3.0DP1 Firmware upgrade Bluetooth is a consolidated and well known standard, anyhow interoperability issues may arise whenever a new version of an operating system (Android, Windows, Linux, iOS, etc.) appear on the market. Bug fixes and new features may also become available. The SPBT3.0DP1 Data Package firmware has been designed to be upgradable via UART interface. It is recommended to support the firmware update procedure in order to always get the benefit of latest firmware versions. ST may update the FW provided with the modules at any time. ST recommends that users regularly check for documentation. The SPBT3.0DP1 module leverages the STM32 built-in bootloader to load the new firmware. It is a three-step procedure: 1. 2. 3. 9.1 Enter bootloader mode Transfer the new firmware Exit bootloader mode Enter bootloader mode To enter the Bootloader mode: 1. 2. 9.2 Set the BOOT pin to HIGH level Reset the module: a. Set the RESET pin to HIGH b. Pause c. Set the RESET pin to LOW Transfer the new firmware The specification of the protocol used in the STM32 bootloader to download the new firmware is described in the document: http://www.st.com/web/en/resource/technical/document/application_note/CD00264342.pdf A reference implementation of the STM32 bootloader protocol can be found at the following link: http://sourceforge.net/projects/stm32flash/ The STM32 Flash loader demonstrator, a Windows GUI that implement that protocol can be downloaded at the following link: http://www.st.com/web/en/catalog/tools/PF257525 9.3 Exit bootloader mode To exit Bootloader mode: 1. 2. 26/35 Set the BOOT pin to LOW Reset the module: a. Set the RESET pin to HIGH b. Pause c. Set the RESET pin to LOW DocID029412 Rev 2 SPBT3.0DP1 Regulatory compliance 10 Regulatory compliance 10.1 FCC certification This module has been tested and found to comply with FCC part 15 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference may not occur in any particular installation. Operation is subject to the following two conditions: 1. 2. This device may not cause harmful interference this device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by STMicroelectronics may render void the user's authority to operate this equipment. The safe user distance for RF exposure is 5 mm (in compliance with 447498 D01 General RF Exposure Guidance v06). Modular approval FCC ID: S9NSPBT30DP1 In accordance with FCC part 15, the SPBT3.0DP1 is listed as a modular transmitter device. This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with collocation and RF exposure requirements in accordance with FCC multi-transmitter product procedures. Collocated transmitters operating in portable RF exposure conditions (e.g. <20 cm from persons including but not limited to body-worn and handheld devices) may require separate approval. 10.1.1 FCC labeling instructions When integrating the SPBT3.0DP1 into the final product, the OEM must ensure that the FCC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates that the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning): Contains FCC ID: S9NSPBT30DP1 OR This product contains FCC ID: S9NSPBT30DP1 The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. 2. this device may not cause harmful interference this device must accept any interference received, including any interference that may cause undesired operation. DocID029412 Rev 2 27/35 Regulatory compliance 10.1.2 SPBT3.0DP1 Product manual instructions for FCC compliance This section applies to OEM final products containing the SPBT3.0DP1 module, subject to FCC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning): Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (Part. 15.21) In the case where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. In cases where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual: Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. 10.2 IC certification The SPBT3.0DP1 module has been tested and found compliant with the IC RSS-210 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference may not occur in any particular installation. This device complies with RSS-210 of the IC rules. Operation is subject to the following two conditions: 1. 2. this device may not cause harmful interference this device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by STMicroelectronics may render void the user's authority to operate this equipment. 28/35 DocID029412 Rev 2 SPBT3.0DP1 Regulatory compliance The safe user distance for RF exposure is 15 mm (in compliance with RSS-102 Issue 5). Modular approval IC: 8976C-SPBT301 In accordance with IC RSS-210, the SPBT3.0DP1 is listed as a modular transmitter device. This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with collocation and RF exposure requirements in accordance with IC multi-transmitter product procedures. Collocated transmitters operating in portable RF exposure conditions (e.g. <20 cm from persons including but not limited to body-worn and handheld devices) may require separate approval. 10.2.1 IC labeling instructions When integrating the SPBT3.0DP1 into the final product, the OEM must ensure that the IC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates that the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning): Contains IC: 8976C-SPBT301 OR This product contains IC: : 8976C-SPBT301 The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches): This device complies with RSS-210 of the IC Rules. Operation is subject to the following two conditions: 1. 2. 10.2.2 this device may not cause harmful interference this device must accept any interference received, including any interference that may cause undesired operation. Product manual instructions for IC compliance This section applies to OEM final products containing the SPBT3.0DP1 module, subject to IC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning): Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (RSS-210) In cases where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. DocID029412 Rev 2 29/35 Regulatory compliance SPBT3.0DP1 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. In cases where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual: Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. 10.3 Bluetooth certification Module with embedded stack and profile has been qualified according to SIG qualification rules: 10.4 Bluetooth SIG Declaration ID: D031101 (subset QDID 84050) Qualified Design ID (QDID): 81857 Product type: End Product Core spec version: 3.0 Product descriptions: Bluetooth module, spec V3.0 CE certification The module has been certified according to the following certification rules: EN 300 328 V 2.1.1 (2016 11) (a) ETSI EN 301 489-17 V3.1.1 (2017-02) (b) ETSI EN 301 489-1 V2.1.1 (2017-02) (c) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 (d) EN 62479:2010 a) EN 300 328 V 2.1.1 (2016 11): "electromagnetic compatibility and radio spectrum Matters (ERM); Wideband transmission systems; data transmission equipment operating in the 2.4 GHZ ISM band and using wideband modulation techniques; harmonized EN covering essential requirements under article 3.2 of the R&TTE directive". b) EN 301 489-17 V 3.1.1 (2017 02): "electromagnetic compatibility and radio spectrum Matters (ERM); electromagnetic compatibility (EMC) standard for radio equipment and services; part 17: specific condition for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment". c) ETSI EN 301 489-1 V2.1.1 (2017 02) : "electromagnetic compatibility and radio spectrum Matters (ERM); electromagnetic compatibility (EMC) standard for radio equipment and services; part 1: Common technical requirements". d) EN60950-1:2006 +A11:2009+A1:2010 +A12:2011+A2:2013: "Information technology equipment - safety". The module is provided by CE marking: 30/35 DocID029412 Rev 2 SPBT3.0DP1 Regulatory compliance Figure 13: CE marking The module has obtained the RED certificate is: No. 0051-RED-0027 REV. 0" The certified module production firmware release is: 1.X For additional information please refer to: STMicroelectronics Via C. Olivetti 2, Agrate Brianza 20864 (ITALY) DocID029412 Rev 2 31/35 Traceability 11 SPBT3.0DP1 Traceability Each module is univocally identified by a serial number stored in a 2D data matrix laser marked on the bottom of the module. The serial number has the following format: WW YY D FF NNN Table 8: Traceability information Letter Meaning WW Week YY Year D Product ID number FF Production panel coordinate identification NN Progressive serial number Each module bulk package is identified by a bulk ID. The Bulk ID and module 2D data matrix are linked by a reciprocal traceability link. The module 2D data matrix traces the lot number of any raw material used. 32/35 DocID029412 Rev 2 SPBT3.0DP1 12 Ordering information Ordering information Table 9: Ordering information Order code SPBT3.0DP1 Description Class 1 OEM Bluetooth antenna module DocID029412 Rev 2 Packing MOQ JEDEC tray 1020 pcs 33/35 Revision history 13 SPBT3.0DP1 Revision history Table 10: Document revision history Date Version 28-Jun-2016 1 Initial release. 2 Updated features in cover page. Updated Table 3: "Absolute maximum ratings". Updated Table 5: "I/O operating characteristics" and Table 6: "Pin assignment". Updated Section 8: "Hardware design". Updated Section 8.3: "GPIO interface". Added figure in Figure 11: "SPBT3.0DP2 to MFi coprocessor interconnections". Updated Section 10.4: "CE certification". Updated Section 8: "Hardware design" Minor text changes. 18-Sep-2017 34/35 Changes DocID029412 Rev 2 SPBT3.0DP1 IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2017 STMicroelectronics - All rights reserved DocID029412 Rev 2 35/35