LQ084S3LG01 - SHARP - Product.Network

Strong 2 SVGA LCD Module featuring

400 nits brightness with 600:1 contrast.

Full Speciﬁcations Listing

LQ084S3LG01 TFT-LCD Module

Product Speciﬁcation

August 2007

LCD Speciﬁcation

LCD Group

Technical Document

RECORDS OF REVISION

ＭＯＤＥＬＮｏ：ＬＱ０８４Ｓ３ＬＧ０１

ＳＰＥＣＮｏ：ＬＣＹ－Ｗ０７８０２

NO. PAGE SUMMARY NOTE

2007. 8.14 - - 1st Issue

LCY-W07802

-1

◎These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include

materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in

any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express

written permission of SHARP.

◎The device listed in this technical literature was designed and manufactured for use in OA equipment.

◎In case of using the device for applications such as control and safety equipment for transportation(aircraft,

trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require

higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and

redundant system design should be taken.

◎Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,

telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment

for life support.

◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply

with the instructions and the precautions specified in these specification sheets.

◎Contact and consult with a SHARP sales representative for any questions about this device.

LCY-W07802

-2

1. Application

This specification applies to the color TFT-LCD module, LQ084S3LG01.

2. Overview

This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).

It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.

Graphics and texts can be displayed on a 800×RGB×600 dots panel with about 16 million colors by using

LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for TFT-LCD panel

driving and supply voltage for backlight.

(Note: Backlight-driving DC/AC inverter is not built in this module.)

a)

Fine images with stripe aligned 480,000 pixels on 8.4 inch diagonal screen

b)

Adapting a wide viewing angle technology [best viewing angle: 6 o’clock direction]

（12 o’clock direction is also available by the function to flip the screen horizontally or vertically）

c)

High contrast, thanks to active matrix drive system

d)

AG(Anti Glare) polarizing filter

e)

Light and slim compact module

f)

Natural coloring reproducibility by employing normally-white-mode, which has good nature in coloring

g)

Image inversion both horizontally and vertically

h)

This module is adapted to RoHS compliance.

3. Mechanical Specifications

Parameter Specifications Unit

Display size 21.3 (Diagonal) cm

8.4 (Diagonal) Inch

Active area 170.4 (H)×127.8 (V) mm

Pixel format 800 (H)×600 (V) Pixel

(1 pixel＝R+G+B dots)

Pixel pitch 0.213 (H)×0.213 (V) mm

Pixel configuration R, G, B vertical stripe

Display mode Normally white

Unit outline dimensions *1 199.5(W)×149.5(H)×11.6(D) mm

Mass 405(MAX) g

Surface treatment Anti-glare and hard-coating

*1.Note: excluding back light cables.

The thickness of module (D) doesn’t contain the projection.

Outline dimensions are shown in Fig.1.

LCY-W07802

-3

4. Input Terminals

4-1. TFT-LCD panel driving

CN1 (Interface signals and +3.3V DC power supply)

Using connectors ：20186-020E-11 (I-PEX)

Corresponding connectors ：FI-SE20ME(Japan Aviation Electronics Industry, Ltd.)

FI-SE20S (Japan Aviation Electronics Industry, Ltd.)

Using LVDS Receiver ：Contained in a control IC. [THC63LVDF84A(Thine) compatible]

Corresponding LVDS Transmitter ：THC63LVDM83R(Thine) or compatible

Pin No.

Symbol Function Remark

1 Vcc +3.3V Power supply

2 Vcc +3.3V Power supply

3 GND Ground

4 GND Ground

5 RxIN0- LVDS CH0 data signal (-) LVDS

6 RxIN0+ LVDS CH0 data signal (+) LVDS

7 GND Ground

8 RxIN1- LVDS CH1 data signal (-) LVDS

9 RxIN1+ LVDS CH1 data signal (+) LVDS

10 GND Ground

11 RxIN2- LVDS CH2 data signal (-) LVDS

12 RxIN2+ LVDS CH2 data signal (+) LVDS

13 GND Ground

14 RxCLKIN- LVDS CK- data signal (-) LVDS

15 RxCLKIN+ LVDS CK+ data signal (+) LVDS

16 GND Ground

17 RxIN3- LVDS CH3 data signal (-) LVDS

18 RxIN3+ LVDS CH3 data signal (+) LVDS

19 REV Reversing terminal

20 LVDS_SET

SELLVDS 【Note1】

※ As for the pin No.1 of this connector, please refer to the figure on page 20.

【Note1】

REV：High REV:Low

LCY-W07802

-4

4-2 Data Mapping

1) 8 bit input

【Note1】pin assignment with SELLVDS pin (Thine:THC63LVDM83R)

Transmitter 20pin LVDS_SET

Pin No Data =H (3.3V) =L (GND) or Open

51

TA

0

R

0

(

LSB

)

R

2

52

TA

1

R

1

R

3

54

TA

2

R

2

R

4

55

TA

3

R

3

R

5

56

TA

4

R

4

R

6

3

TA

5

R

5

R

7

(MSB)

4

TA

6

G

0

(

LSB

)

G

2

6

TB

0

G

1

G

3

7

TB

1

G

2

G

4

11

TB

2

G

3

G

5

12

TB

3

G

4

G

6

14

TB

4

G

5

G

7

(MSB)

15

TB

5

B

0

(

LSB

)

B

2

19

TB

6

B

1

B

3

20

TC

0

B

2

B

4

22

TC

1

B

3

B

5

23

TC

2

B

4

B

6

24

TC

3

B

5

B

7

(MSB)

27

TC

4

(NA)

28

TC

5

(NA)

30

TC

6

DE

50

TD

0

R

6

R

0

(

LSB

)

2

TD

1

R

7

(

MSB

)

R

1

8

TD

2

G

6

G

0

(

LSB

)

10

TD

3

G

7

(

MSB

)

G

1

16

TD

4

B

6

B

0

(

LSB

)

18

TD

5

B

7

(

MSB

)

B

1

25

TD

6

(NA)

LCY-W07802

-5

< SELLVDS = H >

< SELLVDS = L or Open >

G0 R5 R4 R3 R2 R1 R0 R0 R1 G0

B1 B0 G5 G4 G3 G2 G1 G1 G2 B1

DE B5 B4 B3 B2 B2 B3 DE NA NA

1

cycle

NA G7 G6 R7 R6 R6 R7 NA B7 B6

RxCKIN+

RxCKIN-

RXIN0+

RXIN0-

RXIN1+

RXIN2+

RXIN2-

RXIN1-

RXIN3-

RXIN3+

DE : Display Enable

NA : Not Available

RXIN2+

RXIN0+

RXIN1+

RXCXIN+

RXCXIN-

RXIN0-

RXIN2-

RXIN1-

RXIN3-

DE : Display Enable

NA : Not Available

G2 R7 R6 R5 R4 R3 R2 R2 R3 G2

B3 B2 G7 G6 G5 G4 G3 G3 G4 B3

DE B7 B6 B5 B4 B4 B5 DE NA NA

1

cycle

NA G1 G0 R1 R0 R0 R1 NA B1 B0

RXIN3+

LCY-W07802

-6

2) 6 bit input

【Note1】pin assignment with SELLVDS pin (Thine:THC63LVDM83R)

Transmitter 20pin SELLVDS

Pin No Data =H (3.3V) =L (GND) or Open

51

TA

0

－

R

0

(

LSB

)

52

TA

1

－

R

1

54

TA

2

－

R

2

55

TA

3

－

R

3

56

TA

4

－

R

4

3

TA

5

－

R

5

(MSB)

4

TA

6

－

G

0

(

LSB

)

6

TB

0

－

G

1

7

TB

1

－

G

2

11

TB

2

－

G

3

12

TB

3

－

G

4

14

TB

4

－

G

5

(MSB)

15

TB

5

－

B

0

(

LSB

)

19

TB

6

－

B

1

20

TC

0

－

B

2

22

TC

1

－

B

3

23

TC

2

－

B

4

24

TC

3

－

B

5

(MSB)

27

TC

4

－

(NA)

28

T

C

5

－

(NA)

30

TC

6

－

DE

50

TD

0

－

GND

2

TD

1

－

GND

8

TD

2

－

GND

10

TD

3

－

GND

16

TD

4

－

GND

18

TD

5

－

GND

25

TD

6

－

(NA)

1

cycle

RXIN1+

RXCKIN+

RXCKIN-

RXIN0+

RXIN0-

RXIN2-

RXIN1-

DE : Display Enable

NA : Not Available

G0 R5 R4 R3 R2 R1 R0 R0 R1 G0

B1 B0 G5 G4 G3 G2 G1 G1 G2 B1

DE B5 B4 B3 B2 B2 B3 DE NA NA

RXIN2+

LCY-W07802

-7

≪About the connection of RXIN3+ and RXIN3-, in case of supplying 6bit signals.≫

・ RXIN3- ： Please keep the input voltage higher than 1.7V, but less than the power supply

voltage (VLDS+0.3V) of the control IC.

・ RXIN3+ ： Please be connected to the GND.

(Terminal processing example)

V

CN

VCC=3.3V±0.3

2.5

V

(

±

2%

)

62Ω

RXIN3-

GND

RXIN3+

100Ω

(Rating:1/10W)

Set side Module side

Regulator

2.03±0.19V

100～300KΩ

LVDS

Control IC

①

②

⑰

⑱

Vcc

RXIN3-

RXIN3+

4-3 Interface block diagram

LCY-W07802-8

①

8Bit

Mode

SELLVDS=H (20 pin=3.3V)

②

8Bit

Mode

SELLVDS=L(GND or OPEN])

③

6Bit

Mode

SELLVDS=L (GND or OPEN])

(Computer　Side) (TFT-LCD side)

　TC 0 - 6

　TA 0 - 6

　TB 0 - 6

R0-R5,G0

B2-B5, NA,NA,DE

G1-G5,B0,B1

RXIN0+(6)

RXIN0-(5)

TD 0 - 6

7

Controller

TTL PARALLEL-TO-LVDS

PLL

THC63LVDM83R

PLL

RXIN1+(9)

RXIN1-(8)

RXIN2+(12)

RXIN2-(11)

RXCKIN+(15)

RXＣKIN-(14)

CK

CＬK IN

Single LVDS interface contained in a control IC

RXIN3+(18)

RXIN3-(17)

7

R6,R7,G6,G7,

B6,B7,NA

Internal circuits

　RC 0 - 6

　RA 0 - 6

RB 0 - 6

RD 0 - 6

CK OUT

LVDS-TO-PARALLEL TTL

　TC 0 - 6

　TA 0 - 6

　TB 0 - 6

R2-R7,G2

B4-B7, NA,NA,DE

G3-G7,B2,B3

RXIN0+(6)

RXIN0-(5)

TD 0 - 6

7

Controller

TTL PARALLEL-TO-LVDS

PLL

THC63LVDM83R

PLL

RXIN1+(9)

RXIN1-(8)

RXIN2+(12)

RXIN2-(11)

RXCKIN+(15)

RXＣKIN-(14)

CK

CＬK IN

Single LVDS interface contained in a control IC

RXIN3+(18)

RXIN3-(17)

7

R0,R1,G0,G1,

B0,B1,NA

Internal circuits

　RC 0 - 6

　RA 0 - 6

　RB 0 - 6

RD 0 - 6

CK OUT

LVDS-TO-PARALLEL TTL

　TC 0 - 6

　TA 0 - 6

　TB 0 - 6

R0-R5,G0

B2-B5, NA,NA,DE

G1-G5,B0,B1

RXIN0+(6)

RXIN0-(5)

TD 0 - 6

7

Controller

TTL PARALLEL-TO-LVDS

PLL

THC63LVDM83R

PLL

RXIN1+(9)

RXIN1-(8)

RXIN2+(12)

RXIN2-(11)

RXCKIN+(15)

RXＣKIN-(14)

CK

CＬK IN

Single LVDS interface contained in a control IC

RXIN3+(18)

RXIN3-(17)

7

ALL NA

Internal circuits

　RC 0 - 6

　RA 0 - 6

　RB 0 - 6

RD 0 - 6

CK OUT

LVDS-TO-PARALLEL TTL

LCY-W07802

-9

4-4. Backlight

The module-side connector ：BHR-04VS-1 (JST)

The user-side connector

：SM0４(４.0)B-BHS (JST)

Pin no.

symbol

Function

1 VHIGH Power supply for lamp 1 (High voltage side)

2 VHIGH Power supply for lamp 2 (High voltage side)

3 NC Open

4 VLOW Power supply for lamp 1,2 (Low voltage side)

【Note】

The input voltage wave forms to terminal (1) and terminal (2) should be in a same phase.

It has the possibility to discharge abnormally between the terminals in case of input in a reversed phase.

5 Abs

olute Maximum Ratings

Parameter Symbol

Condition

Ratings Unit

Remark

Input voltage VI Ta=25°C

-0.3 ~ Vcc+0.3 V

[Note 1]

Supply voltage Vcc Ta=25°C

0 ~ +4.0 V

-

Storage temperature Tstg - -30 ~ +80 °C

Operating temperature (Panel surface) Topp

- -30 ~ +80 °C

[Note 2,3,4,5

]

[Note 1] CK, R0 ~ R5, G0 ~ G5, B0 ~ B5 and ENAB

[Note 2] Preserve it within this range.

[Note 3] Humidity: Less than 95%RH at Ta ≤ 40°C and

Maximum wet-bulb temperature must not exceed 39°C at Ta>40°C,

with no condensation.

[Note 4] The operating temperature only guarantees operation of the circuit. For contrast, speed response,

and other factors related to display quality, judgment is done using the ambient temperature Ta =+25°C.

[Note 5] This rating applies to all parts of the module and should not be exceed.

LCY-W07802

-10

RGB

G S 0

R G B

G S

4

RGB

G S

8

RGB

G S

6 0

R G B

G S 6 3

. . . .

R

G

B

. . . .

R

G

B

・・・・

R

G

B

R

G

B

R

G

B

....

R

G

B

・・・・

V S V 0 V S V 0 V S V 0

V 0 V S V 0 V S V 0 V S

6. Electrical Characteristics

6-1. TFT-LCD panel driving Ta＝25℃

Parameter Symbol

Min. Typ. Max. Unit

Remark

Supply voltage Vcc +3.0 +3.3 +3.6 V 【Note1】

Current dissipation Icc － 250 380 mA 【Note2】

Input voltage (“High” state)

ＶRIH Vcc×0.7

V 【Note3】

Input voltage (“Low” state)

ＶRIL Vcc×0.3

V

Permissive input ripple voltage V

RF

－－ 100 mVp-p

Terminal resistor RT － 100 － Ω Differential input

Differential input High VIH －－ 100 mV

threshold voltage Low VIL –100 －－ mV

【Note1】

On-off sequences of Vcc and

data

0 <t1<15ms

0 <t2<50ms

0 <t3<50ms

1s<t4

Dip conditions for supply voltage

Vmin,Vth=3.0V,2.4V

1) Vth ≦ Vcc ＜ Vmin

Td≦ 10ms

2) Vcc<Vth

Vcc-dip conditions should also

follow the on-off conditions.

【Note2】 Typical current situation : 64-gray-bar pattern

Vcc=+3.3V, fck=65MHz, Ta=25℃

The explanation of each gray scale is described below section 14.

When VS(V63) and V0 stripe pattern are displayed alternately at intervals of two lines.

(The explanation of each gray scale is described below section 14.)

【Note3】Terminal：REV

2.8V 2.8V

LVDS

Vcc

t3

t4

t1

t2

0.3V 0.3V

Vcc

td

Vth

Vmin

Vth : 2.4V

Vmin : 3.0V

LCY-W07802

-11

6-2. Backlight

The backlight system is an edge-lighting type with two CCFTs (Cold Cathode Fluorescent Tube).

The characteristics of single lamp are shown in the following table.

※Recommended inverter(TDK : CXA-0463)

Ta=25°C

Parameter Symbol

Min. Typ. Max. Unit Remarks

Lamp voltage VL 380 420 460 V rms IL=6mA rms

Lamp current IL 3.0 6.0 6.5 mA rms

[Note6-7]

Lamp power consumption PL - 2.5 - W

Lamp frequency fL 50 - 80 KHz Recommend 55kHz

- - 890 Ta=25°C [Note6-8]

Kick-off voltage

[Note6-1]

Vs

- - 1070

V rms

Ta=-30°C [Note6-8]

Lamp life time L

L

- 50,000 － hour [Note6-9]

[Note6-7]

Lamp current is measured with current meter for high frequency as shown below.

[Note6-8] The open output voltage of the inverter shall be maintained for more than 1sec;

otherwise the lamp may not be turned on.

The input voltage wave forms to terminal ① and terminal ② should be in a same phase. It has

the possibility to discharge abnormally between the terminals in case of input of a reversed phase.

For the sake of the safety, please so design the inveter as to prevent abnormal discharge when one

of the two lamps is broken or reaches the end of life.

[Note6-9] The data for lamp is for your reference, because lamp is consumable component.

a) Lamp life time is defined by either 1or 2 below.

(Continuous turning on at Ta=25℃, IL=6mA rms)

① When a brightness of lamp surface became 50% of the initial value under the standarｄ

condition.

②When a kick-off voltage in Ta= -30℃ exceeded maximum value ((1070) Vrms)

at the output of inverter circuitry

ｂ) In case of operating under lower temp. environment, the lamp exhaustion is accelerated and the

brightness becomes lower.

(Continuous operating for around 1 month under lower temp. condition may reduce the

brightness to half of the original brightness.)

In case of such usage under lower temp. environment, periodical lampexchange is recommended

[Note] The performance of the backlight, for example life time or brightness, is much influenced by the

characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please

make sure that an inadequate lighting caused by the mismatch of the backlight and the inverter

(miss-lighting, flicker, etc.) never occur. When you confirm it, the module should be operated in the

same condition as it is installed in your instrument.

Module DC/AC

INVERTER

①

②

④

A

～

4PIN is V

LOW

LCY-W07802

-12

7. Timing characteristics of input signals

7-1-1. Timing characteristics

Parameter Symbol Min. Typ. Max. Unit Remark

Frequency 1/Tc 35 40 42 MHz

832 1056 1395 clock

Horizontal period TH

20.8 26.4 39.9 µs

Horizontal period (High)

THd 800 800 800 clock

628 666 798 line Vertical period TV

- 17.6 - ms

【Note】

Vertical period (High) TVd 600 600 600 line

【Note1】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.

TVd

TV

Tc

1

2

600 599

1 2 800

THd

TH

800

DE

DATA

(R,G,B)

DE

LCY-W07802

-13

7-2 Input Data Signals and Display Position on the screen

Graphics and texts can be displayed on a panel with 16M colors by supplying 24 bit data signal (8bit/color

[253 gray scales] × 3 ).

D(1,1)

D(2,1)

D(3,1)

D(1,2)

D(2,2)

D(1,3)

D(800,600)

R

G

B

R

G

B

(1,1) (2,1)

R

G

B

D(1,600)

D(800,1)

Display Position of input data ( H , V )

UP

LCY-W07802

-14

8. Input Signals, Basic Display Colors and Gray Scale of Each Color

Data signal

Colors &

Gray

Gray scale

Scale

R0

R1

R2

R3

R4

R5

R6

R7

G0

G1

G2

G3

G4

G5

G6

G7

B0

B1

B2

B3

B4

B5

B6

B7

Black － 0

0

Blue － 0

0

X

1

Green － 0

0

X

1

0

Cyan － 0

0

X

1

X

1

Red － X

X

1

0

Magenta

－ X

X

1

0

X

1

Yellow

－ X

X

1

X

1

0

White

－ X

X

1

X

1

X

1

Black GS0

0

 GS1

1

0

Darker

GS2

0

1

0

    

    

Brighter

GS250

1

0

1

0

 GS251

1

0

1

0

Red GS252

X

1

0

Black GS0

0

 GS1

0

1

0

Darker

GS2

0

1

0

    

    

Brighter

GS250

0

1

0

1

0

 GS251

0

1

0

1

0

Green GS252

0

X

1

0

Black GS0

0

 GS1

0

1

0

Darker

GS2

0

1

0

    

    

Brighter

GS250

0

1

0

1

 GS251

0

1

0

1

Blue GS252

0

X

1

0 : Low level voltage, 1 : High level voltage. X :Don’t care.

Each basic color can be displayed in 253 gray scales from 8 bit data signals. According to the combination of

total 24 bit data signals, the 16M color display can be achieved on the screen.

Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue

LCY-W07802

-15

9. Optical Characteristics Ta=25℃, Vcc =+3.3V

Parameter Symbol Condition

Min. Typ. Max. Unit Remark

θ21

50 65

- Deg.

Horizontal

θ22

CR≧10

50 65

- Deg.

θ11

40 55

- Deg.

Viewing

angle

range

Vertical

θ12

45 60

- Deg.

【

Note1,4

】

Contrast ratio

CR

the best

viewing angle

400 600 - -

【

Note2,4

】

rise τr θ=0°

- 5 15 ms 【Note3,4】 Response

time fall τd - 21 40 ms

X

0.263 0.313 0.363

- 【Note4,5】 Chromaticity of

White Y

θ=0°

0.279 0.329 0.379

-

Luminance of white

Y

L

θ=0°

320 400 - cd/m

2

Direction of

the best

viewing angle

- 6

o’clock

【Note6】

※

The measurement shall be executed 30 minutes after

li

ghting at

rating. ( IL = 6mArms×2 )

Photodetector

Contrast ratio (BM－5A)

Luminance /Chromaticity(SR－3)

Photodetector (EZ－CONTRAST）

TFT

－

LCD Module

Center of screen

(θ=

0

°）

Fig2-1 Viewing angle measurement method

Center of screen

(θ=0°)

TFT

－

LCD Module

４００mm

Field=

２°

Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity

measurement method

Fig2 Optical characteristics measurement method

LCY-W07802

-16

【Note1】Definitions of viewing angle range:

The best viewing angle of this module is slightly leaned to ６ o’clock from normal line.

In the field where θ

１２

exceeds this angle, gray-scale is reversed partially.

The gray-scale in the field of 12 o’clock direction is brighter than that of

６

o’clock

direction and isn’t reversed.

【Note2】Definition of contrast ratio:

The contrast ratio is defined as the following.

Contrast Ratio (CR) ＝

【Note3】Definition of response time:

The response time is defined as the following figure and shall be measured by switching the input

signal for "black" and "white".

【Note4】This shall be measured at center of the screen.

Luminance (brightness) with all pixels white

Luminance (brightness) with all pixels black

Normal line

θ

21

θ

11

θ

12

θ

22

6

o

’

clock

τ

d

τ

r

0

%

10%

90%

100

%

White White Black

Time

Photodetector Output

(Relative Value)

LCY-W07802

-17

10. Handling Precautions

a)

Be sure to turn off the power supply when inserting or disconnecting the cable.

b)

Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or

twist.

c)

Since the front polarize is easily damaged, pay attention not to scratch it.

d)

Since long contact with water may cause discoloration or spots, wipe off water drop immediately.

e)

When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

f)

Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with

care.

g)

Since CMOS LSI is used in this module, take care of static electricity and take the human earth into

consideration when handling.

h)

Make sure the four mounting holes of the module are grounded sufficiently. Take electro-magnetic

interference (EMI) into consideration.

i)

The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any

stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs

may be damaged.

j)

Observe all other precautionary requirements in handling components.

k)

Since it is necessary to remove the screw on the back of a module before performing lamp exchange,

please take a cabinet design into consideration.

l)

When some pressure is added onto the module from rear side constantly, it causes display non-uniformity

issue, functional defect, etc. So, please avoid such design.

m)

When handling LCD modules and assembling them into cabinets, please be noted that long-term

storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,

solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the

LCD modules.

n)

The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching

protective board over the LCD, be careful about the optical interface fringe etc. which degrades

display quality.

LCY-W07802

-18

11. Packing form

a) Maximum number of Carton being stuck:

Max. 6 cartons

b) Maximum number of product contained: 10 Unit

c) Carton size: 408mm (W) x 203mm (D) x 244mm (H)

d) Total mass (for 20Unit): 6kg

e) Fig.3 shows packaging form.

12．Reliability test items

No.

Test parameter Conditions

1

High temperature storage test Leaves the module at Ta=80°C for 240h

2

Low temperature storage test Leaves the module at Ta=-30°C for 240h

3

High temperature

& high humidity operation test

Operates the module at Ta=40°C; 95%RH for 240h

(No condensation)

4

High temperature operation test Operates the module with +80°C at panel surface for 240h

5

Low temperature operation test Operates the module at Ta=-30°C for 240h

6

Vibration test

(non- operating)

Frequency : 10～57Hz/Vibration width (one side):0.15mm

: 58～500Hz/

acceleration

:19.6m/s

2

(2G)

Sweep time : 11 minutes

Test period :1 hour for each direction of X,Y,Z (total 3 hours)

7

Shock test

(non- operating)

Max. acceleration : 686m/s

2

(70G)

Pulse width : 6ms, sine wave

Direction : ±X,±Y,±Z once for each direction.

[Result Evaluation Criteria]

Under the display quality test conditions with normal operation state, these shall be no change which may

affect practical display function.

LCY-W07802

-19

13．Others

1) Lot No.label:

2) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.

If adjusted value is changed, the specification may not be satisfied.

3) Disassembling the module can cause permanent damage and should be strictly avoided.

4) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.

5) When any question or issue occurs, it shall be solved by mutual discussion.

6)

Don’t use or store the module in corrosive gas environment.

7) The LCD has the nature that its performance is degradation by ultra-violet light. Don’t leave the LCD

module in direct sunlight or strong ultra violet ray. (A fall of the contrast, a shift of the chromaticity)

Model name

Country of origin

Revision marks (A, B, C, … )

Interoffice control code (Q, L, etc.)

Serial No. contents

Production year (ex. 2007 → “07”)

Production month (JAN:A, FEB:B,…, DEC:L)

Serial number( 00001 ~ )

LCY-W07802

NORTH AMERICA

Sharp Microelectronics of the Americas

5700 NW Paciﬁc Rim Blvd.

Camas, WA 98607, U.S.A.

Phone: (1) 360-834-2500

Fax: (1) 360-834-8903

www.sharpsma.com

TAIWAN

Sharp Electronic Components

(Taiwan) Corporation

8F-A, No. 16, Sec. 4, Nanking E. Rd.

Taipei, Taiwan, Republic of China

Phone: (886) 2-2577-7341

Fax: (886) 2-2577-7326/2-2577-7328

CHINA

Sharp Microelectronics of China

(Shanghai) Co., Ltd.

28 Xin Jin Qiao Road King Tower 16F

Pudong Shanghai, 201206 P.R. China

Phone: (86) 21-5854-7710/21-5834-6056

Fax: (86) 21-5854-4340/21-5834-6057

Head Ofﬁce:

No. 360, Bashen Road,

Xin Development Bldg. 22

Waigaoqiao Free Trade Zone Shanghai

200131 P.R. China

Email: smc@china.global.sharp.co.jp

EUROPE

Sharp Microelectronics Europe

Division of Sharp Electronics (Europe) GmbH

Sonninstrasse 3

20097 Hamburg, Germany

Phone: (49) 40-2376-2286

Fax: (49) 40-2376-2232

www.sharpsme.com

SINGAPORE

Sharp Electronics (Singapore) PTE., Ltd.

438A, Alexandra Road, #05-01/02

Alexandra Technopark,

Singapore 119967

Phone: (65) 271-3566

Fax: (65) 271-3855

KOREA

Sharp Electronic Components

(Korea) Corporation

RM 501 Geosung B/D, 541

Dohwa-dong, Mapo-ku

Seoul 121-701, Korea

Phone: (82) 2-711-5813 ~ 8

Fax: (82) 2-711-5819

JAPAN

Sharp Corporation

Electronic Components & Devices

22-22 Nagaike-cho, Abeno-Ku

Osaka 545-8522, Japan

Phone: (81) 6-6621-1221

Fax: (81) 6117-725300/6117-725301

www.sharp-world.com

HONG KONG

Sharp-Roxy (Hong Kong) Ltd.

3rd Business Division,

17/F, Admiralty Centre, Tower 1

18 Harcourt Road, Hong Kong

Phone: (852) 28229311

Fax: (852) 28660779

www.sharp.com.hk

Shenzhen Representative Ofﬁce:

Room 13B1, Tower C,

Electronics Science & Technology Building

Shen Nan Zhong Road

Shenzhen, P.R. China

Phone: (86) 755-3273731

Fax: (86) 755-3273735

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for

limitations on special applications. See Limited Warranty for SHARP’s product warranty.

The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,

ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in

any way, for any incidental or consequential economic or property damage.

LCD Group

LCD Speciﬁcation

Technical Document