H7HP-A - OMRON - Product.Network

CSM_H7HP_DS_E_5_3

Total Counter/Time Counter (DIN 72 x 36)

H7HP

DIN 72 x 36-mm Total Counter/Time Counter with

Easy-to-read Displays and Water and Oil

Resistance Equivalent to IP66

• Large, easy-to-read displays: 15-mm-high characters for 6-digit models;

12-mm-high characters for 8-digit models.

• High-visibility, negative transmissive LCD display with built-in red LED

backlight at low power consumption.

• IP66 with oil resistance and NEMA4 are achieved by unifying the front

with the casing case and using oil-resistant materials and parts.

• Compact (66 mm) body.

• Switch 6-digit models between total counter and time counter operation.

• Just change a switch setting for either an NPN or PNP input.

• Supports both external resetting and manual resetting.

• Finger-protection terminal block cover prevents electrical shock and

conforms to VDE0106, Part 100.

• Safety standards: UL, CSA, EMC (EN 61326), CE Marking.

Model Number Structure

■Model Number Legend

1. Classification

A: Total counter/time counter

C: Total counter

2. Digits

None: 6 digits

8: 8 digits

3. Supply Voltage

None: 100 to 240 VAC

D: 12 to 24 VDC

4. Case Color

None: Light gray (Munsell 5Y7/1)

B: Black

Ordering Information

■List of Models

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

1 2 3 4

H7HP-@@@@

Supply voltage 6-digit total counter/time counter 8-digit total counter

Light gray Black Light gray Black

100 to 240 VAC H7HP-A H7HP-AB H7HP-C8 H7HP-C8B

12 to 24 VDC H7HP-AD H7HP-ADB H7HP-C8D H7HP-C8DB

H7HP

Specifications

■Ratings

Note: 1. Contains 20% ripple (p-p) max.

2. Only a non-voltage input (NPN transistor) is possible for the key protection input. The key protection input will be a non-voltage input even

if the NPN/PNP input mode is set to PNP. Key protection is used to prohibit operating the Reset Key. The reset input terminals will still be

functional.

Item 6-digit total counter/time counter 8-digit total counter

H7HP-A H7HP-AD H7HP-C8 H7HP-C8D

Rated supply voltage 100 to 240 VAC (50/60 Hz) 12 to 24 VDC (see note 1) 100 to 240 VAC (50/60 Hz) 12 to 24 VDC (see note 1)

External power supply 50 mA at 12 VDC --- 50 mA at 12 VDC ---

Operating voltage range 85% to 110% of rated supply voltage

Power consumption 100 to 240 VAC: 6.5 VA max.

12 to 24 VDC: 0.6 W max.

Dimensions 72 x 36 x 66 mm (W x H x D)

Mounting method Flush mounting

External connections Screw terminals

Degree of protection Panel surface: IP66 with oil resistance, NEMA 4 (indoors). Panel surface only: IEC IP66. IEC IP66

Display 7-segment, negative transmissive LCD (with red backlight)

Digits 6 digits (15-mm-high characters) 8 digits (12-mm-high characters)

Function Total counter/time counter (selected via DIP switch) Total counter

Input mode Up/down (individual) (total counter), or accumulative

(time counter)

Up/down (individual)

Max. counting speeds 30 Hz or 5 kHz (selected via DIP switch)

Counting range –99999 to 999999 –9999999 to 99999999

Time specification 0.1 to 99999.9 h/1 s to 99 h 59 min 59 s

(selected via DIP switch)

---

Timing accuracy ±100 ppm (–10°C to 55°C) ---

Memory backup EEP-ROM (overwrites: 200,000 times min.) that can store data for 20 years min.

Input Input signals Count 1/start, count 2/gate, reset, and key protection (see note 2)

Input method No-voltage input (NPN transistor input) or voltage input (PNP transistor input) (selected via DIP switch)

Count, start,

gate, reset

No-voltage input (NPN transistor input)

Short-circuit (ON) impedance: 1 kΩ max.

Short-circuit (ON) residual voltage: 2 VDC max.

Open (OFF) impedance: 100 kΩ min.

Voltage input (PNP transistor input)

Short-circuit (ON) impedance: 1 kΩ max.

ON voltage: 9 to 24 VDC

OFF voltage: 5 VDC max.

Open (OFF) impedance: 100 kΩ min.

Key protection No-voltage input (NPN transistor input)

Short-circuit (ON) impedance: 1 kΩ max.

Short-circuit (ON) residual voltage: 0.5 VDC max.

Open (OFF) impedance: 100 kΩ min.

Input re-

sponse

speed

Reset Time counter: 20 ms; total counter: 20 ms or 1 ms (automatically switched according to counting speed)

Start Time counter: 20 ms

Key protection Approx. 1 s Approx. 1 s

Reset system External and manual resets

H7HP

■Characteristics

Note: 1. Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

2. UL508 and CAN/CSA-C22.2 No.14 certification conditions

•Power supply 100 to 240VAC types

Ambient temperature 30°C Single mounting

•Power supply 12 to 24VDC types

Ambient temperature 40°C Single mounting

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength 2,000 VAC, 50/60 Hz for 1 min between current-carrying terminal and exposed non-current-carrying metal parts

(AC model)

1,000 VAC, 50/60 Hz for 1 min between current-carrying terminal and exposed non-current-carrying metal parts

(DC model)

2,000 VAC, 50/60 Hz for 1 min between power terminals and control input terminals (AC model)

Impulse withstand voltage 3 kV (between power terminals) (1 kV for 12-to-24-VDC models)

4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) (1.5 kV for 12-to-24-VDC

models)

Noise immunity ±1.5 kV (between AC power terminals), ±480 V (between DC power terminals),

±480 V (between input terminals);

square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)

Static immunity Display: Malfunction: 8 kV

Destruction: 15 kV

DIP switch: Malfunction: 4 kV

Destruction: 8 kV

Vibration resistance Destruction: 10 to 55 Hz with 0.75-mm single amplitude, 2 hours each in three directions

Malfunction: 10 to 55 Hz with 0.5-mm single amplitude, 10 minutes each in three directions

Shock resistance Destruction: 294 m/s2 each in three directions

Malfunction: 196 m/s2 each in three directions

Ambient temperature Operating: –10°C to 55°C (with no icing)

Storage: –25°C to 65°C (with no icing)

Ambient humidity Operating: 35% to 85%

EMC (EMI) EN61326-1 (note 1.)

Emission Enclosure: EN55011 Group 1 class A

Emission AC Mains: EN55011 Group 1 class A

(EMS) EN61326-1 (note 1.)

Immunity ESD: EN61000-4-2: 4 kV contact discharge (level 2)

8 kV air discharge (level 3)

Immunity RF-interference: EN61000-4-3: 10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);

10 V/m (Pulse-modulated, 900 MHz ±5 MHz) (level 3)

Immunity Conducted Disturbance: EN61000-4-6: 10 V (0.15 to 80 MHz) (according to EN61000-6-2)

Immunity Burst: EN61000-4-4: 2 kV power-line (level 3);

2 kV I/O signal-line (level 4)

Immunity Surge: EN61000-4-5: 1 kV line to lines (power and output lines) (level 2);

2 kV line to ground (power and output lines) (level 3)

Immunity Voltage Dip/Interruption: EN61000-4-11: 0.5 cycle, 100% (rated voltage)

Approved standards UL508 (note 2), CSA C22.2 No.14 (note 2), conforms to EN61010-1, VDE0106/P100

Case color Rear section: Gray smoke; Front section: 5Y7/1 (light gray) or N1.5 (black)

Weight Approx. 115 g

H7HP

Connections

■Terminal Arrangement

Note: 1. Incremented for count 1 (CP1) inputs; decremented for count 2 (CP2) inputs.

2. Non-contact input is also available.

Operation

■DIP Switch Settings

Switches 1 to 4 are all set to OFF before shipping.

H7HP-A@

H7HP-C@

Note: When the setting has been changed, turned power off and on

to continue. The display will show “0” when the power is turned

back on.

12 VDC0 V

5678910 11

1234

0 V

5678910 11

1234

12 VDC0 V

567891011

1234

0 V

567891011

1234

NPN mode

Unused Unused Unused

PNP mode

100 to 240 VAC

AC Models

H7HP-A

Unused Unused Unused

12 to 24 VDC

NPN mode

PNP mode

Unused Unused

Unused Unused Unused

NPN mode

PNP mode

100 to 240 VAC

Unused Unused Unused

12 to 24 VDC

NPN mode PNP mode

Unused Unused

H7HP-C8

H7HP-C8D

DC Models

H7HP-AD

External power supply

12 VDC 50 mA max.

Power

supply

Power

supply

Key

protection

input

Reset

input

Count 1

input or

start input

Count 2

input or

gate input

Power

supply

Key

protection

input

Reset

input

Count 1

input or

start input

Count 2

input or

gate input

External power supply

12 VDC 50 mA max.

Power

supply

Power

supply

Key

protection

input

Reset

input

Count 2

input

Power

supply

Key

protection

input

Reset

input

Count 1

input

Count 2

input

Count 1

input

Pin no. Item OFF ON

1 Function Total counter Time counter

2 Counting speed

(note)

30 Hz 5 kHz

Time range (note) 99999.9 h 99 h 59 min 59 s

3 Input mode (note) NPN PNP

4Unused --- ---

Pin no. Item OFF ON

1Unused --- ---

2 Counting speed

(note)

30 Hz 5 kHz

3 Input mode (note) NPN PNP

4Unused --- ---

H7HP

■Operating Modes

Nomenclature

0.0 h

CP1

CP2

Total Counters

Time Counters

Reset input

Display

display

Reset input

Gate input

Start input

999999

(see note)

−99999

(see note)

99999.9h *

Note: Display values are shown for a 6-digit model.

The count value will return to "0" when "999999" is exceeded.

The display and output are turned OFF when the power

supply turns OFF, but the count value is stored internally.

Note: The count value will return to "0" when "99999.9" is exceeded.

The display and output are turned OFF when the power supply

turns OFF, but the count value is stored internally.

* Display values are shown for full scale set to 99999.9 h.

1. Reset Key

Resets the count value, but will not operate while the keys are protected.

2. Key Protection Indicator

Lit while the keys are protected (Reset Key is disabled.).

3. DIP Switch

Use to change a setting. Refer to DIP Switch Settings for details.

(The figure shows the DIP switch

label stuck to the rear of the case.)

H7HP

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Panel Cutouts

With Flush Mounting Bracket

Terminal cover (provided)

Panel

M3.5 terminal screw

H7HP-A

H7HP-C8

Panel cutouts are as shown below

(according to DIN43700).

Note: 1. The mounting panel thickness should

be 1 to 6 mm.

2. Water resistance will be lost if Counters

are mounted side-by-side.

Y92S-33 rubber

packing (provided)

Y92F-33 flush mounting

adaptor (provided)

H7HP

Connections (Common)

■Input Connections

Note: The following is common for all H7GP/H7HP models.

No-voltage Input (NPN Input Mode)

Voltage Input (PNP Input Mode)

0 V

Reset, Count 1, Count 2, Start, and Gate Inputs

Reset, Count 1, Count 2, Start, and Gate Inputs Specification

Note: Two-wired sensors cannot be used.

Key Protection Input

Key Protection Inputs Specification

Note: Two-wired sensors cannot be used.

Sensor

Reset input

Count 1 input

Count 2 input

Start input

Gate input

Short-circuit (ON) impedance: 1 kΩ max.

Short-circuit (ON) residual voltage: 2 VDC max.

Current flow for 0-Ω short-circuit: Approx. 2 mA

Open (OFF) impedance: 100 kΩ min.

Key

protection

input

Short-circuit (ON) impedance: 1 kΩ max.

Short-circuit (ON) residual voltage: 0.5 VDC max.

Current flow for 0-Ω short-circuit: Approx. 0.5 mA

Open (OFF) impedance: 100 kΩ min.

12 VDC

Reset input

Count 1 input

Count 2 input

Start input

Gate input

Sensor

H7GP/H7HP

Voltage Output

H7GP/H7HP

12 VDC

Key

protection

input

Sensor

Open Collector Output

Voltage Output Open Collector Output

12 VDC

(12 to 24 VDC)

12 VDC

0 V

12 VDC

Reset, Count 1, Count 2, Start, and Gate Inputs

Reset, Count 1, Count 2, Start, and Gate Inputs Specification

Note: Two-wired sensors cannot be used.

Sensor

Reset input

Count 1 input

Count 2 input

Start input

Gate input

Short-circuit (ON) impedance: 1 kΩ max.

ON voltage: 9 to 24 VDC

OFF voltage: 5 VDC max.

Open (OFF) impedance: 100 kΩ min.

Input impedance: Approx. 3.8 kΩ

12 VDC

0 V

H7HP

Safety Precautions (Common)

Refer to Safety Precautions for All Counters.

Note: The following is common for all H7GP/H7HP models.

■Precautions for Safe Use

Observe the following items to ensure the safe use of this product.

Environmental Precautions

•Store the H7GP/H7HP within the specified ratings. If the H7GP/

H7HP has been stored at temperatures −10°C or lower, let it stand

for 3 hours or longer at room temperature before turning ON the

power supply.

•Use the H7GP/H7HP within the specified ratings for operating

temperature and humidity.

•Do not operate the H7GP/H7HP in locations subject to sudden or

extreme changes in temperature, or locations where high humidity

may result in condensation.

•Do not use the H7GP/H7HP in locations subject to vibrations or

shock. Extended use in such locations may result in damage due to

stress.

•Do not use the H7GP/H7HP in locations subject to excessive dust,

corrosive gas, or direct sunlight.

•Install the H7GP/H7HP well away from any sources of static

electricity, such as pipes transporting molding materials, powders,

or liquids.

•The H7GP/H7HP is not waterproof or oil resistant.

Do not use it in locations subject to water or oil.

•The life expectancy of internal components may be reduced if the

H7GP/H7HP is mounted side-by-side.

•Do not use organic solvents (such as paint thinner or benzine),

strong alkaline, or strong acids because they will damage the

external finish.

Usage Precautions

•Install a switch or circuit breaker that allows the operator to

immediately turn OFF the power, and label it to clearly indicate its

function.

•Be sure to wire the terminals correctly.

•Do not install input lines in the same duct or conduit as power

supply or other high-voltage lines. Doing so may result in

malfunction due to noise. Separate the input lines from high-

voltage lines.

•Internal elements may be destroyed if a voltage outside the rated

voltage is applied.

•Maintain voltage fluctuations in the power supply within the

specified range.

•Use a switch, relay, or other contact so that the rated power supply

voltage will be reached within 0.1 s. If the power supply voltage is

not reached quickly enough, the H7GP/H7HP may malfunction or

outputs may be unstable.

•Although the H7GP/H7HP power supply (primary side) is isolated

from control circuits (secondary side) by a transformer, the primary

and secondary sides of the transformer are linked by a capacitor,

making it possible for high-frequency components to leak to the

secondary side. Take adequate precautions against electrical

shock. Do not connect input circuits to exposed parts (such as the

machine body) and be sure that the power supply is turned off

before wiring.

Flush Mounting

The panel surface is water-resistive (conforming to NEMA 4 and

IP66). In order to prevent the internal circuit from water penetration

through the space between the counter and operating panel, attach a

rubber packing between the counter and operating panel and secure

the rubber packing with the Y92F-3@ flush-mounting adaptor.

Be sure the rubber packing is installed in the correct direction. The

wider portion must be facing the panel when installed, as shown in

the following illustration. Using a flat-head screwdriver, press in the

Mounting Adapter until it cannot be pressed in any further in order to

ensure water-resistive performance.

Other

Oil resistance is not applicable to all types of oil. Be sure to test any

specific oils before actual application.

This may occasionally cause electric shock, fire, or malfunction.

Never disassemble, repair, or modify the H7GP/H7HP.

This may occasionally cause electric shock, fire, or malfunction.

Do not allow metal fragments or lead wire scraps to fall inside the

H7GP/H7HP.

!CAUTION

Control

circuit

Display

circuit

Input

circuit

Adapter

Panel

Wider portion

facing panel

H7HP

■Precaution for Correct Use

Power Supplies

When turning the power ON and OFF, input signal reception is

possible, unstable, or impossible as shown in the diagram below.

Apply the power supply voltage through a relay or switch in such a

way that the voltage reaches a fixed value immediately.

Self-diagnostic Function

The following displays will appear if an error occurs.

Labels

Unit labels are included with the H7GP/H7HP and DIP switch labels

are included with the H7HP. Attach these labels as shown in the

following illustrations.

Display Error Correction

---- Less than –99999

(H7HP, 6-digit model)

Less than –99999999

(H7HP, 8-digit model)

Press RST Key or reset

input

e1 CPU Press RST Key or turn

power OFF and then ON

e2 Memory

200 ms 5 ms

Input Impossible

Unstable

Possible ImpossibleUnstable

0 to 90 ms 0 to 2 s

OFF

Power

supply

Unit Labels

H7GP

H7HP

DIP Switch Labels

H7HP

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2016.8

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/