3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle – Shielded 102 Series
• Rugged die-cast body resists tipping during automated
soldering operations
• Wiper-on-wiper contact for reliable repetitive plugging
• Ultra-low signal skew for high data rate transmission
• Interface latch design for connection stability
• Suitable for thumbscrew attach (see TS-0142 for
available hardware)
• MDR digital LCD interface as a 20 or 26 contact
connector
• Camera Link® interface as a 26 contact connector
• Contacts: 14, 20, 26, 40 and 50
• See Regulatory Information Appendix (RIA) for
chemical compliance information
Date Modified: December 20, 2007 TS‑2242‑A
Sheet 1 of 3
Physical
Body Material:
Flammability:
Alignment Plate Material:
Flammability:
Contact Material:
Underplating:
Wiping Area Plating:
Solder Tail Plating:
Shroud Material:
Plating:
Lock Stand Material:
Plating:
Glass Reinforced Polyester (PCT), Natural Color
UL 94V-0
LCP, Natural Color
UL 94V-0
Copper Alloy
80 µ” [2 µm] Nickel
See Ordering Information
Flash Gold over Nickel (RIA E1 & C1 apply)
Steel
Nickel
Zinc Alloy
Nickel
Electrical
Current Rating:
Insulation Resistance:
Withstanding Voltage:
1 A
>5 x 108 Ω at 500 VDC
500 VRMS for 1 minute
Environmental
Temperature Rating:
Process Rating:
-55 °C to +85 °C
240°C- 250°C peak temperature for less than 10 secs., 220°C soldering for 30 – 60 secs. after
150°C - 180°C preheat for 90 –120 secs. (reflow two times)
UL File No.: E68080 Camera Link® is a trademark of Automated Imaging Assocition
3
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of the 3M Company
For technical, sales or ordering information call
800-225-5373
3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle — Shielded 102 Series
Ordering Information 102XX-1S10 PX
Contact Quantity
See Table
Wiping Area Plating:
L = 8 µ” min. Gold with Lubricant Treatment
E = 20 µ” min. Gold
C = 30 µ” min. Gold
T-T
T
DETAIL-N
M2.5 MARK PIN
FLAT FIXTURE
SURFACE
0.635
[.025]
0.25
[.010]
DIM. C
DIM. B
DIM. D
DIM. E
9.1
[.36]
9.35
[.368]
1.20
[.047]
DIM. H
1.27±0.10
[.050±0.004]
DIM. G
DIM. F
DIM. A
7.2
[.28]
0.00 TO 0.10
[.000 TO .004]
3.5
[.14]
4.8
[.19]
11.5
[.45]
2.9
[.11]
16.7
[.66]
2.8
[.11]
6.3
[.25]
4.8
[.19]
9.1
[.36]
0.3
[.01]
4.75
[.187] 10.0
[.39]
1.9
[.07]
15°
T
TAIL COPLANARITY
0.00 TO 0.10
MARK PIN
N
MARK PIN
MARK PIN
M2.5
TS‑2242‑A
Sheet 2 of 3
3
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of the 3M Company
For technical, sales or ordering information call
800-225-5373
mm
(inch)
Tolerance Unless Noted
.0 .00 .000
mm ±.3 ±.15 ±.150
( ) Dimensions used for
Reference Only
Contact
Quantity DIM A DIM B DIM C DIM D DIM E DIM F DIM G DIM H
14 29.5
(1.16)
23.64
(.931)
8.255
(.325)
17.1
(.67)
19.5
(.77)
12.6
(.50)
7.62
(.300)
12.70
(.500)
20 33.3
(1.31)
27.45
(1.081)
12.065
(.475)
21.0
(.83)
23.4
(.92)
16.4
(.65)
11.43
(.450)
16.51
(.650)
26 37.2
(1.46)
31.26
(1.231)
15.875
(.625)
24.8
(.98)
27.2
(1.07)
20.2
(.80)
15.24
(.600)
20.32
(.800)
40 46.1
(1.81)
40.15
(1.581)
24.765
(.975)
33.7
(1.33)
36.1
(1.42)
29.1
(1.15)
24.13
(.950)
29.21
(1.150)
50 52.4
(2.06)
46.50
(1.831)
31.115
(1.225)
40.0
(1.57)
42.4
(1.67)
35.5
(1.40)
30.48
(1.200)
35.56
(1.400)
3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle — Shielded 102 Series
DIM. M
DIM. L
DIM. K
DIM. J
2.2225 REF
[.0875]
0.635±0.02
[.025±.001]
0.400±0.02
[.016±.001]
Ø2.80+0.10
-0.00
[Ø.110+.004
-.000 ]
Ø2.00+0.10
-0.00
[Ø.079+.004
-.000 ]
1.00
[.039]
2.00
[.079]
4.75
[.187]
3.84±0.10
[.151±.004]
6.74
[.265]
7.24
[.285]
3.00
[.118]
EDGE OF PWB
7.20±0.15
[.283±.006]
0.50 TYP
[.020]
4.94 REF
[.195]
2.90 REF
[.114] 7.84±0.15
[.309±.006]
12.00
[.47]
"LOCK STAND"
MOUNTING AREA
ONLY SOLDER PAD
PATTERN
PROHIBITION AREA
4.20
[.165]
MARK PIN
MARK PIN
DIM. N
DIM. P
R1.50
[R.059] 8.10±0.1
[.319±.004]
TS‑2242‑A
Sheet 3 of 3
Recommended Board Layout
Viewed from Connector Side
Recommended Panel Cutout
Panel Thickness: 2.0 mm (.08 inch) Max.
Note: The connector should be mounted to the panel and printed circuit board with screws. See TS-0142 for mounting hardware.
3
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of the 3M Company
For technical, sales or ordering information call
800-225-5373
Contact
Quantity DIM J DIM K DIM L DIM M DIM N DIM P
14 29.5
(1.16)
23.64
(.931)
12.70
(.500)
8.255
(.325)
19.9
(.78)
23.64 ± .13
(.931)
20 33.3
(1.31)
27.45
(1.081)
16.51
(.650)
12.065
(.475)
23.8
(.94)
27.45 ± .13
(1.081)
26 37.2
(1.46)
31.26
(1.231)
20.32
(.800)
15.875
(.625)
27.6
(1.09)
31.26 ± .13
(1.231)
40 46.1
(1.81)
40.15
(1.581)
29.21
(1.150)
24.765
(.975)
36.5
(1.44)
40.15 ± .13
(1.581)
50 52.4
(2.06)
46.50
(1.831)
35.56
(1.400)
31.115
(1.225)
42.8
(1.69)
46.50 ± .13
(1.831)
mm
(inch)
Tolerance Unless Noted
.0 .00 .000
mm ±.3 ±.05 ±.050
( ) Dimensions used for
Reference Only
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-c
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-c
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2007. All rights reserved.
RIA-2217B-c
3
3M Electronics
Interconnect Products
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects 3M is a trademark of 3M Company.
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
